2012 Dodge Grand Caravan Owners Manual

(RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press a second time to turn each light off. You may adjust the direction of these lights by pressing the outside ring, which is identified with four directional arrows (LED lamps only). The area around the instrument panel cupholders is also illuminated from a light in the overhead console (pre- mium console only). This light is turned on when the headlight switch is on, and will adjust in brightness when the dimmer control is rotated up or down.

Sunglass Storage (Non-Sunroof Only) At the front of the overhead console, a compartment is provided for the storage of two pairs of sunglasses. From the closed position, press the door latch to open the compartment.

The door will slowly rotate to the full open position.

Over Door Latch

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229

Full Open Position

Conversation Mirror Position

From this position, the door can be fully closed or, by rotating upward about 3/4 of the way and releasing, positioned for conversation mirror use.

NOTE: From the “conversation mirror” position, the door can only be closed. To return to the full open position, the door must first be closed and then opened by pressing the latch again to release.

230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press the lens a second time to turn each light off. You may adjust the direction of these lights by pressing the outside ring, which is identified with four directional arrows.

Reading Lights

Rear Overhead Consoles — If Equipped The rear overhead storage system is available in two versions: with or without sunroof. An additional LED at the front of the rear console shines down on the front foot-well area while in courtesy mode, for added convenience.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231

Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “Lights/ Halo Lights — If Equipped” in “Understanding the Features Of Your Vehicle” for further information.

GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three hand-held transmitters that operate devices such as garage door openers, motor- ized gates, lighting or home security systems. The HomeLink威 unit is powered by your vehicles 12 Volt battery.

Overhead Compartment Features

1 — DVD 1
2 — Rear HVAC 3 — Interior Lights 4 — Storage 1 If equipped, otherwise storage.

5 — Storage 6 — DVD 1
7 — Interior Lights 8 — Halo Lighting

232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons, located on either the overhead console, headliner or sunvisor, designate the three differ- ent HomeLink威 channels. The HomeLink威 indicator is located above the center button.

HomeLink威 Buttons/Sunvisor/Headliner

NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active.

HomeLink威 Buttons/Overhead Consoles

Before You Begin Programming HomeLink姞 Be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink威 system. Erase all channels before you begin programming. To erase the channels place the ignition in the ON/RUN

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233
position and press and hold the two outside HomeLink威 buttons (I and III) for up 20 seconds or until the red indicator flashes. NOTE: • Erasing all channels should only be performed when programming HomeLink威 for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.

234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer.

Training The Garage Door Opener

1 — Door Opener 2 — Training Button 1. Turn the ignition switch to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the HomeLink威 indicator light in view.

3. Simultaneously press and hold both the Homelink威 button you want to program and the hand-held transmit- ter button. 4. Continue to hold both buttons and observe the indi- cator light. The Homelink威 indicator will flash slowly and then rapidly after Homelink威 has received the fre- quency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid. 5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is attached to the garage door opener/device motor. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235
NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 6. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the garage door opener/device activates, programming is complete. If the garage door opener/device does not NOTE: activate, press the button a third time (for two seconds) to complete the training. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels. Reprogramming A Single HomeLink威 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position.

236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “Program- ming A Rolling Code” Step 2 and follow all remaining steps. Programming A Non-Rolling Code For programming Garage Door Openers manufactured before 1995. 1. Turn the ignition switch to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the HomeLink威 indicator light in view. 3. Simultaneously press and hold both the Homelink威 button you want to program and the hand-held transmit- ter button.

4. Continue to hold both buttons and observe the indi- cator light. The Homelink威 indicator will flash slowly and then rapidly after Homelink威 has received the fre- quency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid. 5. Press and hold the programmed HomeLink威 button and observe the indicator light. • If the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the HomeLink威 button is pressed. • To program the two remaining HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels.

Reprogramming A Single HomeLink威 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “Program- ming A Non-Rolling Code” Step 2 and follow all remain- ing steps. Canadian/Gate Operator Programming For programming transmitters in Canada/United States that require the transmitter signals to “time-out” after several seconds of transmission. Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for HomeLink威

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237
to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Turn the ignition switch to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the HomeLink威 indicator light in view. 3. Continue to press and hold the HomeLink威 button, while you press and release (“cycle”), your hand-held transmitter every two seconds until HomeLink威 has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained.

238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Watch for the HomeLink威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming. 5. Press and hold the programmed HomeLink威 button and observe the indicator light. • If the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the HomeLink威 button is pressed. • To program the two remaining HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels.

If you unplugged the garage door opener/device for programming, plug it back in at this time.

Reprogramming A Single HomeLink威 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without the button proceed with “Canadian/Gate Operator Programming” Step 2 and follow all remaining steps. Using HomeLink姞 To operate, press the programmed HomeLink威 button. Activation will now occur for the programmed device (i.e., garage door opener, gate opera- tor, security system, entry door lock, home/office light- ing, etc.,). The hand-held transmitter of the device may also be used at any time.

and release

releasing

Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239

Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original hand-held transmit- • Press the LEARN button on the Garage Door Opener • Did you unplug the device for programming and

to complete the training for a Rolling Code.

ter.

remember to plug it back in?

If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.

240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

• Your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515
or, on the Internet at www.HomeLink.com for safety information or assistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death.

General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for com- pliance could void the user’s authority to operate the device. • The term IC before the certification/registration num- Industry Canada technical

ber only signifies that specifications were met.

POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console.

Power Sunroof Switch

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241

WARNING!

• Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passen- gers are properly secured. • Do not allow small children to operate the sun- roof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result.

242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express Press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Opening The Sunroof — Manual Mode To open the sunroof, press and hold the switch rearward to full open. Any release of the switch will stop the movement and the sunroof will remain in a partially opened condition until the switch is pushed and held rearward again. Closing Sunroof — Express Press the switch forward and release it within one-half second, and the sunroof will close automatically from any position. The sunroof will close fully and then stop

automatically. This is called “Express Close”. During Express Close operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof — Manual Mode To close the sunroof, press and hold the switch in the forward position. Any release of the switch will stop the movement and the sunroof will remain in a partially closed condition until the switch is pushed and held forward again. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction is detected, the sunroof will automatically re- tract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close.

If three consecutive sunroof close attempts re- NOTE: sult in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing the sunroof, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move toward the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — Express Press and release the “Vent” button, and the sunroof will open to the vent position. This is called “Express Vent”, and will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243

Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) is in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.

244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. NOTE: For vehicles equipped with the EVIC, the power sunroof switch will remain active for up to approxi- mately ten minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.

Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed.

ELECTRICAL POWER OUTLETS — IF EQUIPPED Two 12 Volt (13 Amp) power outlets are located on the lower instrument panel, below the open storage bin. The driver-side power outlet is controlled by the ignition switch and the passenger-side power outlet is connected directly to the battery. The driver-side power outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245

CAUTION!

• Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.

Instrument Panel Outlets

NOTE: To ensure proper operation a MOPAR威 cigar knob and element must be used.

246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE One outlet in the removable floor console (if equipped) shares a fuse with the lower outlet in the instrument panel and is also connected to the battery. Do not exceed a maximum power of 160 Watts (13 Amps) shared between the lower panel outlet and the removable floor console outlet.

On vehicles equipped with the Super Console the power outlets are located under the retractable cover. To access the power outlets push down on the cover and slide it toward the instrument panel.

Removable Console Outlet

Super Console Outlets

The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both con- trolled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets. The power outlets include tethered caps, labeled with a key or battery symbol indicating the power source. The power outlet, located on the lower instrument panel, is powered directly from the battery. Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247

Power Outlet Fuses

1 — M7 Fuse 20 A Yellow Power Outlet Center Seat (Opt) or with Console Rear 2 — M6 Fuse 20 A Yellow Cigar Lighter Instrument Panel or with Console Front 3 — M36 Fuse 20 A Yellow Power Outlet Instrument Panel or with Console Center

248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an

the vehicle.

electric shock and failure.

CAUTION!

• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.

(Continued)

CAUTION! (Continued)

• Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery. • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage.

POWER INVERTER — IF EQUIPPED A 110 Volt, 150 Watt inverter outlet (if equipped) converts DC current to AC current, and is located on the left rear trim panel immediately behind the second row left passenger seat.

Power Inverter Outlet

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249
The power inverter switch is located on the instrument panel below the climate controls. To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150
Watts. Certain high-end video games, such as Playsta- tion3 and XBox360 will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON.

250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter.

CUPHOLDERS There are cupholders located throughout the interior. All liners are removable for cleaning. Pull the flexible liner from the cupholder drawer or tray starting at one edge for easy removal. Refer to “Cleaning The Instrument Panel Cupholders” in “Maintaining Your Vehicle” for further information. Instrument Panel Cupholders The instrument panel cupholders are located in a pull-out drawer just above the lower storage bin.

Front Cupholders

Pull the drawer out firmly until it stops, and place the container to be held in either one of the cupholder wells. The cupholders are designed to accommodate a wide variety of container types and sizes. Press down on the container to engage the cupholder retention features.

Super Console — If Equipped On models equipped with the Super Console, there are two cupholders located in the center of the console.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251
For rear passengers two cupholders are located in the pull-out drawer, located in the back of the Super Console. Pull the drawer out to the first position to use the cupholders.

Super Console Cupholders

Rear Cupholders

252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Premium Console Cupholders — If Equipped On models equipped with premium center consoles, there are four cupholders located on the top of the console.

Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommo- dates up to a 20 oz (.6 L) plastic bottle.

WARNING!

If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants. Be careful when closing the doors to avoid injury.

Premium Console Cupholders

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253

Smoker’s Package Kit — If Equipped With the optional authorized dealer-installed Smoker’s Package Kit, a removable ash receiver is inserted into one of the two cupholders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward. Press the ash receiver into either of the cup wells to secure. Pull upward on the ash receiver to remove for cleaning and/or storage. The left rear trim panel cupholder is designed to accom- modate a second ash receiver, if desired.

Interior Bottle Holder

Two outboard mesh pockets are on intermediate seating. The mesh pockets are flexible enough to hold juice boxes, toys, games or MP3 players, etc.

254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE

Glove Compartments Upper and lower glove compartments are located on the passenger side of the instrument panel.

Upper Glove Compartment To open the upper compartment, press in on the button, located on the left side of the upper door. The door will automatically open.

Upper and Lower Glove Compartments

Upper Compartment

To close the compartment door, push downward on the door’s surface to latch the door closed.

Lower Glove Compartment To open the lower compartment pull out on the release handle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255
NOTE: The lower compartment is equipped with a lock that is part of the compartment handle. Door Trim Panel Storage

Front Door Storage Both interior front door panels have multiple pockets for storage.

Lower Compartment

256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Seatback Storage — If Equipped The driver’s seatback has a primary storage pocket on all models and an optional secondary mesh pocket.

Umbrella Holder An umbrella holder has been conveniently molded into the left front door entry scuff molding.

Driver’s Seatback Storage

Umbrella Holder

1 — Bag Holder 2 — Standard Pocket 3 — Mesh Pocket

Second Row Seat Storage Bins — If Equipped The seat storage bins are located on the floor in front of the second row seats. The area below the covers can be used for storage when the second row seat is in the upright position. Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the ⬙Lock⬙ position to allow greater access to the storage bin.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257

Storage Bin

CAUTION!

NOTE: The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

In a collision, serious injury could result if the seat storage bin covers are not properly latched. • DO NOT drive the vehicle with the storage bin • Keep the storage bin covers closed and latched • DO NOT use a storage bin latch as a tie down.

while the vehicle is in motion.

covers open.

Storage Bin Safety Warning Carefully follow these warnings to help prevent personal injury or damage to your vehicle:

WARNING!

• Always close the storage bin covers when your

vehicle is unattended.

(Continued)

WARNING! (Continued)

• Do not allow children to have access to the second row seat storage bins. Once in the storage bin, young children may not be able to escape. If trapped in the storage bin, children can die from suffocation or heat stroke. • In a collision, serious injury could result if the seat • Do not drive the vehicle with the storage bin covers open. Keep the storage bin covers closed and latched while the vehicle is in motion. • Do not operate the storage bin covers while the • Do not use a storage bin latch as a tie down.

storage bin covers are not properly latched.

vehicle is in motion.

CAUTION!

The storage bin cover must be flat and locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

Seat Storage Bin Cover Emergency Release Lever As a security measure, your vehicle may be built with a Storage Bin Cover Emergency Release is built into the storage bin cover latching mechanism.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259

Storage Bin Cover Emergency Release Lever

In the event of an individual being locked inside NOTE: the storage bin, the storage bin cover can be opened from inside of the bin by pushing on the glow-in-the-dark lever attached to the storage bin cover latching mechanism.

260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo Area Storage The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.

Rear Cargo Area Loading Limit

NOTE: With all rear seats stowed or removed, 4 x 8foot sheets of building material will fit on the vehicle floor with the liftgate closed. The front seats must be moved slightly forward of the rearmost position.

CONSOLE FEATURES There are three consoles available: Basic, Premium and Super.

WARNING!

Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injury.

Basic Console Basic Console features consist of the following: • The basic console profile allows vehicle occupants to

easily pass through the first row to the second.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261

• Four cupholders accept up to extra large size beverage cups or 20 oz (.6 L) plastic bottles. Cupholders are dishwasher safe for cleaning. • The cupholders are removable to access a large storage • The basic console is removable from the vehicle for additional floor space by removing the cap and clip at the console base.

bin.

To Remove The Basic Floor Console 1. Remove the front anchor cup plug and clip. 2. Slide the console base forward while lifting slightly to clear the rear load floor hook. 3. Remove the console.

262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Reinstall The Basic Floor Console 1. Position the console at a slight angle (front slightly higher than the rear). 2. Slide the console rearward into the floor bracket/ hook. 3. Align the console until the front anchor cup plug hole is centered on the winch hole. 4. Reinstall the clip first and then while pushing down- ward on the console with slight pressure, reinstall the cover plug. 5. Pull up on the console to be sure it is firmly latched.

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

Premium Console — If Equipped The three-compartment console with sliding storage bin, sliding upper tray with storage and large console storage bin offers multiple configurations. • Four cupholders with dishwasher safe liners for clean- ing. The cupholders can accept plastic bottles, large cups or mugs with handles.

• Top tray storage • Upper storage bin can hold nine regular or 18 thin CDs

or other items

• Large console center storage will store headphones for the available rear DVD entertainment system or other items • 12 Volt DC power outlet provides continuous power inside the console for cell phones or other electronics. • Rear occupant accessible • Multiple adjustments • Removable from vehicle for additional floor space. The top and center console sections slide forward and rearward to provide added user comfort. A one-piece cup holder insert for both cavities can easily be removed for cleaning. The cupholders will also accommodate large size cups and 20 oz (.6 L) bottles.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263
Position 1 shows the console closed with four cupholders and a convenient storage tray.

Console Position 1

264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 shows the raised storage tray revealing a large storage area below.

easy access to the storage area below and provides two of the four cupholders for the second row passengers.

Console Position 2

Console Position 3

Dual Storage Bins Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console. This provides

Position 4 shows the complete console in its rearmost position. Again, lifting second latch handle at the front of the console, allows complete access to a lower storage bin and provides additional cupholders for rear passengers.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265
3. Pull rearward to disengage from floor and remove console. To reinstall the console: 1. Position the console at a slight angle (rear slightly higher than the front). 2. Slide the console forward into the floor bracket. 3. Rotate the rear of the console down until it is resting on the floor bracket. 4. Push down on the rear of the console until it is seated in the rear floor bracket. 5. Pull up on the console to be sure it is firmly latched.

Console Position 4

To Remove The Premium Floor Console 1. Pull up on the bottom release handle in the front of the console. 2. Lift centimeters.

the console up several

the rear of

inches/

266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

Super Console — If Equipped The Super Console contains multiple storage areas, front lower pass through, top forward bin, top rearward bin and rear pull out drawer. The super console contains a pass through storage area accessible for both the driver and front passenger.

Front Lower Pass Through

The super console tambour doors are opened by pushing down on the finger tabs and sliding the door. The front tambour door slides forward, the rear tambour door slides rearward.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267
NOTE: The front cupholder light ring and pass through lighting is controlled by a dimming switch located on the instrument panel, refer to “Lights” in “Understanding The Features Of Your Vehicle” for further information. Located in the back of the super console is a storage drawer and cupholders for the rear passengers.

Super Console

1 — Front Sliding Tambour Door 2 — Cupholder Light Ring 3 — Rear Sliding Tambour Door

Rear Drawer Storage

268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES

Rechargeable Flashlight The rechargeable flashlight is mounted on the right side of the cargo area. The flashlight snaps out of the bezel when needed. The flashlight features two bright LED light bulbs and is powered by a lithium battery that recharges when snapped back into place and the vehicle is either running or the key is in the accessory position. Press in on the flashlight to release it.

Press And Release

To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269

REAR WINDOW FEATURES

Rear Window Defroster

The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ap- proximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: • You can turn off the heated mirror feature at anytime by pressing the rear window defroster switch a second time. • To prevent excessive battery drain, use the rear win-

dow defroster only when the engine is operating.

Three-Press Switch

270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window.

REAR LOAD-LEVELING SYSTEM — IF EQUIPPED The automatic load-leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions. If the leveled vehicle is not moved for approximately 15 hours, the leveling system will bleed itself down. The vehicle must be driven to reset the system.

ROOF LUGGAGE RACK — IF EQUIPPED The crossbars on your vehicle are delivered stowed within the roof rack side rails. If adding cargo, deploy the crossbars. Distribute cargo weight evenly on the roof rack crossbars, to maximum of 150 lbs (68 kg). The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271

Crossbar Stowed In Side Rail

The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars.

272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Crossbars are error-proofed and cannot be deployed or • To help control wind noise, stow the crossbars in the

stowed in the incorrect positions.

side rails when they are not in use.

Deploying the Crossbars To deploy the crossbars, completely loosen the thumb screws at both ends of the crossbar and lift the crossbar from its stowed position in the side rail. Repeat with crossbar on the opposite side.

Loosening Crossbars

CAUTION!

Use care when removing and handling the crossbars to prevent damage to the vehicle.

Bend the crossbar supports at each end, taking care to keep hand clear of pivoting joint. Slide the thumb screw down.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273

Then, position the crossbars across the roof.

Deployed Position

Stowed Position

274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The crossbars are identical and can be placed in any two of the three deploy positions.

Deploy Positions – Choose Two Of Three

Make sure the directional arrows on the crossbars align with the directional arrows on the side rails. Set the crossbars into the deployed positions.

Crossbar To Side Rail Installation

Once the crossbars are set into position, tighten the thumb screws completely.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275
NOTE: Load should always be secured to crossbars first, with rail tie down loops used as additional securing points if needed. Tie loops are intended as supplemen- tary tie down points only. Do not use ratcheting mecha- nisms with the tie loops.

Tightening Crossbar

Stowing the Crossbars Reverse the procedure to stow the crossbars, again, taking care to keep hand clear of pivoting joint. Crossbars are identical and can be stowed in either rail nest. Once the crossbars are stowed, tighten the thumb screws completely.

Rail Tie Loops

276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

tighten thumb screws as necessary.

• Check deployed crossbars frequently and re- • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately. • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without the crossbars deployed. • The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or other protective layer between the load and the roof surface.

(Continued)

CAUTION! (Continued)

• Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • Travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.

WARNING!

Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.

SUN SCREENS — IF EQUIPPED Sun screens are available for second and third row seating windows. The screens store in the sill trim panels, and the tops of the windows are equipped with hooks that the sun screens attach to when pulled out.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277

Sun Screen Retracted

Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window.

278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window.

To lower the sun screen, gently lift the tab upward to disengage the hooks, and feed the screen back into the base sill.

Sun Screen Extended

UNDERSTANDING YOUR INSTRUMENT PANEL

CONTENTS

䡵 Instrument Panel Features . . . . . . . . . . . . . . . 283
䡵 Instrument Cluster — Base . . . . . . . . . . . . . . . 284
䡵 Instrument Cluster — Premium . . . . . . . . . . . 285
䡵 Instrument Cluster Descriptions . . . . . . . . . . . 286
䡵 Electronic Vehicle Information Center

(EVIC) — If Equipped . . . . . . . . . . . . . . . . . . . 300
▫ Electronic Vehicle Information Center

(EVIC) Displays . . . . . . . . . . . . . . . . . . . . . 302
▫ EVIC White Telltale Lights . . . . . . . . . . . . . . 305
▫ EVIC Amber Telltale Lights . . . . . . . . . . . . . 306

▫ EVIC Red Telltale Lights . . . . . . . . . . . . . . . 306
▫ Oil Change Required . . . . . . . . . . . . . . . . . . 309
▫ Fuel Economy . . . . . . . . . . . . . . . . . . . . . . 310
▫ Vehicle Speed . . . . . . . . . . . . . . . . . . . . . . . 311
▫ Trip Info . . . . . . . . . . . . . . . . . . . . . . . . . . 311
▫ Tire PSI . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
▫ Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
▫ Vehicle Info

(Customer Information Features)

. . . . . . . . . 312

280 UNDERSTANDING YOUR INSTRUMENT PANEL

▫ Messages # . . . . . . . . . . . . . . . . . . . . . . . . . 313
▫ Compass / Temperature Display . . . . . . . . . 313
▫ Customer-Programmable Features

(System Setup)

. . . . . . . . . . . . . . . . . . . . . . 315

䡵 Media Center 730N/430/430N (RHR/RER/

RBZ/RHB) CD/DVD/HDD/NAV — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 322
▫ Operating Instructions (Voice Command

System) — If Equipped . . . . . . . . . . . . . . . . 322

▫ Operating Instructions

(Uconnect™ Phone) — If Equipped . . . . . . . 322
䡵 Media Center 130 (Sales Code RES) . . . . . . . . . 322
▫ Operating Instructions — Radio Mode . . . . . 323
▫ Operation Instructions — CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . 326

▫ Notes On Playing MP3 Files . . . . . . . . . . . . 328
▫ Operation Instructions - Auxiliary Mode . . . . 330

䡵 Media Center 130 With Satellite Radio

(Sales Code RES+RSC). . . . . . . . . . . . . . . . . . . 331
▫ Operating Instructions — Radio Mode . . . . . 331
▫ Operation Instructions — CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . 337
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 339
▫ List Button (CD Mode For MP3 Play) . . . . . . 341
▫ Info Button (CD Mode For MP3 Play) . . . . . . 341
▫ Uconnect™ Multimedia (Satellite Radio) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 342

▫ Operating Instructions

(Uconnect™ Phone) — If Equipped . . . . . . . 346

䡵 iPod威/USB/MP3 Control — If Equipped . . . . . 346

▫ Connecting The iPod威 Or External USB

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
▫ Using This Feature . . . . . . . . . . . . . . . . . . . 348
▫ Controlling The iPod威 Or External USB

Device Using Radio Buttons . . . . . . . . . . . . . 348
▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 349
▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 350
▫ Bluetooth Streaming Audio (BTSA) . . . . . . . . 352

䡵 Uconnect™ Multimedia Video Entertainment

System (VES)™ — If Equipped . . . . . . . . . . . . 353
▫ Getting Started . . . . . . . . . . . . . . . . . . . . . . 353
▫ Play Video Games . . . . . . . . . . . . . . . . . . . . 354

UNDERSTANDING YOUR INSTRUMENT PANEL 281

▫ Listen To An Audio Source On Channel 2

While A Video Is Playing On Channel 1 . . . . 357
▫ Dual Video Screen . . . . . . . . . . . . . . . . . . . 359
▫ Play A DVD Using The Touch-Screen

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359

▫ Play A DVD Using The VES™ Player

(If Equipped)

. . . . . . . . . . . . . . . . . . . . . . . 362

▫ Listen To An Audio Source While A Video Is

Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
▫ Third Row Swivel Screen (If Equipped) . . . . . 367
▫ Important Notes For Dual Video Screen

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
▫ Remote Control . . . . . . . . . . . . . . . . . . . . . 368
▫ Remote Control Storage . . . . . . . . . . . . . . . . 371
▫ Locking The Remote Control . . . . . . . . . . . . 371

282 UNDERSTANDING YOUR INSTRUMENT PANEL

▫ Replacing The Remote Control Batteries . . . . 372
▫ Headphones Operation . . . . . . . . . . . . . . . . 372
▫ Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
▫ Replacing The Headphone Batteries . . . . . . . 374
▫ Unwired威 Stereo Headphone Lifetime

Limited Warranty . . . . . . . . . . . . . . . . . . . . 374
▫ System Information . . . . . . . . . . . . . . . . . . . 376

䡵 Steering Wheel Audio Controls —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 390
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . 391
▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 391
䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 392
䡵 Radio Operation And Mobile Phones . . . . . . . 392

䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 393

▫ Manual Heating And Air Conditioning

System — If Equipped . . . . . . . . . . . . . . . . . 393

▫ Rear Manual Climate Control —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 398

▫ Automatic Temperature Control (ATC) — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 400
▫ Summer Operation . . . . . . . . . . . . . . . . . . . 411
▫ Winter Operation . . . . . . . . . . . . . . . . . . . . 411
▫ Vacation/Storage . . . . . . . . . . . . . . . . . . . . 412
▫ Window Fogging . . . . . . . . . . . . . . . . . . . . 412
▫ Outside Air Intake . . . . . . . . . . . . . . . . . . . 412
▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 413
▫ A/C Air Filter . . . . . . . . . . . . . . . . . . . . . . 413

INSTRUMENT PANEL FEATURES

UNDERSTANDING YOUR INSTRUMENT PANEL 283

1 — Air Vents 2 — Instrument Cluster 3 — Shift Lever 4 — Radio

5 — Upper Glove Compartment 6 — Lower Glove Compartment 7 — Climate Controls 8 — DVD – If Equipped

9 — Storage Bin 10 — Cup Holders 11 — Switch Bank 12 — Ignition Switch

13 — Hood Release 14 — Dimmer Switch 15 — Headlight Switch

284 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE

INSTRUMENT CLUSTER — PREMIUM

UNDERSTANDING YOUR INSTRUMENT PANEL 285

286 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS

1. Tachometer The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 2. Front Fog Light Indicator — If Equipped

This indicator will illuminate when the front fog lights are on.

3. Park/Headlight ON Indicator — If Equipped

This indicator will illuminate when the park lights or headlights are turned on.

4. Turn Signal Indicators

The arrow will flash with the exterior turn signal when the turn signal lever is operated.

If the vehicle is driven more than 1 mile (1.6 km) with either turn signal on, a continuous chime will sound to alert you to turn the signal off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 5. High Beam Indicator

This indicator shows that the high beam head- lights are on. Push the multifunction lever forward to switch the headlights to high beam, and pull toward yourself (normal position) to return to low beam. 6. Odometer Display / Electronic Vehicle Information Center (EVIC) Display — If Equipped

Odometer Display / Trip Odometer Display The odometer display shows the total distance the ve- hicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your

odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero. This also displays Trip A and Trip B, DTE, MPG or L/100km, OAT (Outside Air Temperature) information to Base Cluster, use STEP and RESET button (on steering wheel) to access or reset the display. For further informa- tion refer to “Compass Mini-Trip Computer”.

UNDERSTANDING YOUR INSTRUMENT PANEL 287

Message Display Area When the appropriate conditions exist, the following odometer messages will display:

door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar gATE . . . . . . . . . . . . . . . . . . . . . . . . . . . Liftgate Ajar LoW tirE. . . . . . . . . . . . . . . . . . . . . Low Tire Pressure gASCAP . . . . . . . . . . . . . . . . . . . . . . . Fuel Cap Fault noFUSE . . . . . . . . . . . . . . . . . . . . . . . . . . Fuse Fault CHAngE OIL . . . . . . . . . . . . . . . Oil Change Required LoCOOL . . . . . . . . . . . . . . . . . . . . . . . . Low Coolant NOTE: Some of the above warnings will be displayed in the Electronic Vehicle Information Center Display Area located in the instrument cluster. Refer to ”Electronic Vehicle Information Center (EVIC) Display — If Equipped” for further information.

288 UNDERSTANDING YOUR INSTRUMENT PANEL LoW tirE When the appropriate condition exists, the odometer display will toggle between LoW and tirE for three cycles. gASCAP If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gASCAP” message will display in the odometer display area. Tighten the fuel filler cap properly and press the STEP button on the steering wheel to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. noFUSE If the vehicle diagnostic system determines that the Ignition Off Draw (IOD) fuse is improperly installed, or damaged, a “noFUSE” message will display in the odom- eter display area. For further information on fuses and fuse locations refer to “Fuses” in “Maintaining Your Vehicle”.

CHAngE OIL Your vehicle is equipped with an engine oil change indicator system. The CHAngE OIL message will flash in the instrument cluster odometer for approximately 12 seconds, after a single chime has sounded, to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle-based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the STEP button on the steering wheel. To reset the oil change indicator system (after performing the scheduled maintenance), perform the following steps. 1. Turn the ignition switch to the ON/RUN position (do not start the engine).

2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to the OFF/LOCK position. If the indicator message illuminates when you NOTE: start the engine, the oil change indicator system did not reset. If necessary, repeat these steps. Electronic Vehicle Information Center (EVIC) Display — If Equipped The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the instrument cluster. For further information, refer to “Electronic Vehicle Information Center (EVIC)”. 7. Anti-Lock Brake (ABS) Light

This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON/RUN position and may stay on for as long as four seconds.

UNDERSTANDING YOUR INSTRUMENT PANEL 289
If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the ignition switch is turned to the ON/RUN position, have the light inspected by an authorized dealer. 8. Tire Pressure Monitoring Telltale Light — If Equipped

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the

290 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to

maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more

tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

CAUTION!

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

UNDERSTANDING YOUR INSTRUMENT PANEL 291

9. Malfunction Indicator Light (MIL)

The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD, that monitors engine and automatic transmission con- trol systems. The light will illuminate when the key is in the ON/RUN position, before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing.

292 UNDERSTANDING YOUR INSTRUMENT PANEL

CAUTION!

Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.

WARNING!

A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others.

10. Electronic Stability Control (ESC) Activation/ Malfunction Indicator Light — If Equipped

The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running. If the “ESC Activation/Malfunction In- dicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. NOTE: • The “ESC Off

Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on mo- mentarily each time the ignition switch is turned to ON/RUN.

• Each time the ignition is turned to ON/RUN, the ESC system will be ON, even if it was turned off previously. • The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.

11. Electronic Stability Control (ESC) OFF Indicator Light — If Equipped

This light indicates the Electronic Stability Con- trol (ESC) is off.

12. Speedometer Indicates vehicle speed.

UNDERSTANDING YOUR INSTRUMENT PANEL 293

13. Fuel Door Reminder

The arrow in this symbol is a reminder that the Fuel Filler Door is located on the left side of the vehicle.

14. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position. 15. Air Bag Warning Light

This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information.

294 UNDERSTANDING YOUR INSTRUMENT PANEL 16. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. NOTE: • You must apply the brakes before shifting from PARK. • The highest available transmission gear is displayed in the lower right corner of the Electronic Vehicle Infor- mation Center (EVIC) whenever the Electronic Range Select (ERS) feature is active. Use the +/- selector on the shift lever to activate ERS. Refer to “Automatic Transmission” in “Starting And Operating” for further information.

17. Vehicle Security Light — If Equipped

This light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.

18. Brake Warning Light

This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop.

The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary.

UNDERSTANDING YOUR INSTRUMENT PANEL 295

WARNING!

Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.

296 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN posi- tion. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 19. Seat Belt Reminder Light

When the ignition switch is first turned to ON/ RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver or front passenger’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat belt remains unbuckled, the Seat Belt Reminder Light will illuminate and the chime will sound. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information.

20. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.

CAUTION!

Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an autho- rized dealership for service.

WARNING!

A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see “Main- taining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph.

21. Low Fuel Light

When the fuel level reaches approximately 2.0 gal (7.8 L) this light will turn on, and remain on until fuel is added.

22. Charging System Light

This light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first turned to ON/RUN and remain on briefly as a bulb check. If the light stays on or comes on

UNDERSTANDING YOUR INSTRUMENT PANEL 297
while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an autho- rized dealer. If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. 23. Oil Pressure Warning Light

This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood.

298 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Engine Temperature Warning Light

This light warns of an overheated engine condi- tion. As engine coolant temperatures rise and the gauge approaches H , this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the tempera- ture gauge to pass H , the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for further information.

25. Electronic Throttle Control (ETC) Light

This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned to ON/RUN and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position, the light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing.

26. Transmission Temperature Warning Light

During sustained high speed driving or trailer towing up long grades on hot days, the auto- matic transmission oil may become too hot. When the transmission overheat warning light turns on, you will experience reduced vehicle perfor- mance until the automatic transmission cools down. Once the transmission has cooled down and the light turns off, you may continue to drive normally. If the high speed is maintained, the overheating will continue to occur. If the overheating continues, it may become necessary to stop the vehicle and run the engine at idle with the transmission in NEUTRAL until the light turns off.

UNDERSTANDING YOUR INSTRUMENT PANEL 299

CAUTION!

Continuous driving with the Transmission Tempera- ture Warning Light illuminated will eventually cause severe transmission damage or transmission failure.

WARNING!

If the Transmission Temperature Warning Light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.

300 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the instrument cluster.

Electronic Vehicle Information Center (EVIC)

This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: • Radio Information • Fuel Economy • Vehicle Speed • Trip Info • Tire PSI • Vehicle Info • Messages • Units • System Setup (Personal Settings) • Turn Menu Off

The system allows the driver to select information by pressing the following buttons mounted on the steering wheel:

EVIC Steering Wheel Buttons

UNDERSTANDING YOUR INSTRUMENT PANEL 301

UP Button

Press and release the UP button to scroll up- ward through the main menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages, Units, System Setup) and sub-menus.

DOWN Button

Press and release the DOWN button to scroll downward through the main menus and sub- menus.

SELECT Button

The SELECT button allows access to informa- tion in EVIC submenus, selects some feature settings, and resets some EVIC features. The EVIC prompts the driver when the SELECT button can be used by displaying the right arrow graphic.

302 UNDERSTANDING YOUR INSTRUMENT PANEL BACK Button

Press the BACK button to scroll back to a previous menu or sub-menu.

Electronic Vehicle Information Center (EVIC) Displays The EVIC display consists of three sections: 1. The top line where compass direction, odometer line and outside temperature are displayed. 2. The main display area where the menus and pop up messages are displayed. 3. The reconfigurable telltales section below the odom- eter line.

The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays ⬙pop up⬙ messages that consist of approximately 60 possible warn- ing or information messages. These pop up messages fall into several categories: • Five Second Stored Messages When the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen. Most of the messages of this type are then stored (as long as the condition that activated it remains active) and can be reviewed from the ⬙Messages⬙ main menu item. As long as there is a stored message, an ⬙i⬙ will be displayed in the EVIC’s compass/outside temp line. Examples of this message type are ⬙Right Front Turn Signal Lamp Out⬙ and ⬙Low Tire Pressure⬙.

• Unstored Messages This message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are ⬙Turn Signal On⬙ (if a turn signal is left on) and ⬙Lights On⬙ (if driver leaves the vehicle). • Unstored Messages Until RUN These messages deal primarily with the Remote Start feature. This message type is displayed until the ignition is in the RUN state. Examples of this message type are ⬙Remote Start Aborted - Door Ajar⬙ and ⬙Press Brake Pedal and Push Button to Start⬙. • Five Second Unstored Messages When the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen. Ex- amples of this message type are ⬙Memory System Un- available - Not in Park⬙ and ⬙Automatic High Beams On⬙.

UNDERSTANDING YOUR INSTRUMENT PANEL 303
The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left. When the appropriate conditions exist, the EVIC displays the following messages: • Key in ignition • Ignition or Accessory On • Remote start aborted — Door ajar • Remote start aborted — Hood ajar • Remote start aborted — L/Gate ajar • Remote start aborted — Fuel low • Remote start disabled — Start Vehicle to Reset • Remote start active — Key to Run • Wrong Key

motion)

304 UNDERSTANDING YOUR INSTRUMENT PANEL

• Damaged Key • Key not programmed • Vehicle Not in Park • Press Brake Pedal and Push Button to Start • Door(s) Ajar (with a single chime, if vehicle is in • Liftgate Ajar (chime will sound when vehicle starts • Low Tire Pressure • Service TPM System (refer to “Tire Pressure Monitor- • Premium TPM Service Graphic Display • Turn Signal On • RKE Battery Low

ing System” in “Starting And Operating”)

moving)

• LOW WASHER FLUID • Oil Change Required • Left Front Turn Signal Light Out • Left Rear Turn Signal Light Out • Right Front Turn Signal Light Out • Right Rear Turn Signal Light Out • Park Assist Disabled • Service Park Assist System • Personal Settings Not Available — Vehicle Not In Park • Blind Spot System Off — This message is displayed when the ignition is turned to ON to indicate the Blind Spot System has been turned off.

• Blind Spot System Not Available — This message is displayed to indicate the Blind Spot Monitor (BSM) system is temporarily unavailable due to sensor block- age, electronic interference, or other ⬙temporary⬙ con- ditions. When this message is displayed both outside rear view icons will be illuminated. If electronic inter- ference is present, the BSM system will illuminate the icon only on the side of interference as long as interference is present. • Service Blind Spot System — This message is dis- played to indicate the Blind Spot Monitor (BSM) system is permanently unavailable. The driver will receive an EVIC message and the BSM display warn- ing in both mirrors will be permanently illuminated. If this message is present see an authorized dealer.

UNDERSTANDING YOUR INSTRUMENT PANEL 305

EVIC White Telltale Lights This area will show reconfigurable white caution tell- tales. These telltales include: • Electronic Range Select (ERS) Status The shift lever status “5,4,3,2,1” are displayed indicating the shift lever position. Telltales “5,4,3,2,1” indicate the Electronic Range Select (ERS) feature has been engaged and the gear selected is displayed. For further informa- tion on ERS, refer to “Starting And Operating” • Electronic Speed Control Ready

This light will turn on when the electronic speed control is ready. For further information, refer to “Electronic Speed Control” in “Under- standing The Features Of Your Vehicle.”

306 UNDERSTANDING YOUR INSTRUMENT PANEL

• Electronic Speed Control SET

This light will turn on when the electronic speed control is SET. For further information, refer to “Electronic Speed Control” in “Under- standing The Features Of Your Vehicle.”

EVIC Amber Telltale Lights This area will show reconfigurable amber caution tell- tales. These telltales include: • Low Fuel Light

When the fuel level reaches approximately 3.0 gal (11.0 L) this light will turn on, and remain on until fuel is added.

• Loose Gascap Indicator

If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the telltale display area. Tighten the fuel filler cap properly and press the SELECT button

to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL). • Windshield Washer Fluid Low Indicator

This light will turn on to indicate the wind- shield washer fluid is low.

EVIC Red Telltale Lights This area will show reconfigurable red telltales. These telltales include: • Door Ajar

This light will turn on to indicate that one or more doors may be ajar.

• Oil Pressure Warning Light

This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. • Charging System Light

This light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the

UNDERSTANDING YOUR INSTRUMENT PANEL 307
vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an autho- rized dealer. If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. • Electronic Throttle Control (ETC) Light

This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position. The light should turn off.

308 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • Engine Temperature Warning Light

This light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H, the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also,

shift the transmission into NEUTRAL and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for more information. • Transmission Temperature Warning Light

This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmission into NEUTRAL and run the engine at idle or faster until the light turns off.

CAUTION!

Continuous driving with the Transmission Tempera- ture Warning Light illuminated will eventually cause severe transmission damage or transmission failure.

WARNING!

If the Transmission Temperature Warning Light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.

Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The Oil Change Required message will flash in the EVIC display for approximately 10 seconds, after a single chime has sounded, to indicate the next scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style.

UNDERSTANDING YOUR INSTRUMENT PANEL 309
Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the Menu button. To reset the oil change indicator system (after performing the scheduled maintenance), perform the following steps. 1. Turn the ignition switch to the ON position (do not start the engine.) 2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to the OFF/LOCK position. If the indicator message illuminates when you NOTE: start the engine, the oil change indicator system did not reset. If necessary, repeat these steps.

310 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Economy Press and release the UP or DOWN button until “Fuel Economy” displays highlighted in the EVIC and press the SELECT button. The following Fuel Economy func- tions display in the EVIC: • Average Fuel Economy (AVG) • Distance To Empty (DTE) • Miles Per Gallon (MPG) Average Fuel Economy This display shows the average fuel economy since the last reset. The Average Fuel Economy can be reset by following the prompt in the EVIC to use the SELECT button. When the fuel economy is reset, the display will read “zero” for two seconds. Then, the history informa- tion will be erased, and the averaging will continue from the last fuel average reading before the reset.

Average Fuel Economy Display

Distance To Empty (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank. This esti- mated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the SELECT button.

NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a “LOW FUEL” message. This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the “LOW FUEL” message and a new DTE value will display. Miles Per Gallon (MPG) This display shows the instantaneous MPG in bar graph form while driving. This will monitor the gas mileage in real-time as you drive and can be used to modify driving habits in order to increase fuel economy. Vehicle Speed Press and release the UP or DOWN button until “Vehicle Speed” displays highlighted in the EVIC and press the SELECT button. Press the SELECT button to display the

UNDERSTANDING YOUR INSTRUMENT PANEL 311
current speed in mph or km/h. Pressing the SELECT button a second time will toggle the unit of measure between mph or km/h. NOTE: Changing the unit of measure in the Vehicle Speed menu will not change the unit of measure in the EVIC.