2013 Dodge Durango Owners Manual

Download PDF Manual
OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and storage for sunglasses. Universal Garage Door Opener (HomeLink®), power liftgate and power sunroof switches may also be included, if equipped. Front Map/Reading Lights Lights are mounted in the overhead console. Each light can be turned on by pressing the switch on either side of the console. These buttons are backlit for night time visibility. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Overhead Console Front Map/Reading Lights 262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the lights off, press the switch a second time. The lights also turn on when a door is opened. The lights will also turn on when the UNLOCK button on the RKE is pressed. Courtesy Lights The courtesy lights can be turned on by pressing the top corner of the lens. To turn the lights off, press the lens a second time. Courtesy Lights Sunglasses Bin Door At the front of the console a compartment is provided for the storage of a pair of sunglasses. The storage compart- ment access is a “push/push” design. Push the chrome pad on the door to open. Push the chrome pad on the door to close. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 The HomeLink® buttons, located on either the overhead console, headliner or sunvisor, designate the three differ- ent HomeLink® channels. The HomeLink® indicator is located above the center button. Sunglasses Bin Door GARAGE DOOR OPENER — IF EQUIPPED HomeLink® replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink® unit operates off your vehicle’s battery. HomeLink® Buttons/Overhead Consoles 264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HomeLink® Buttons/Sunvisor/Headliner NOTE: HomeLink® is disabled when the Vehicle Secu- rity Alarm is active. Before You Begin Programming HomeLink® Be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system. Erase all channels before you begin programming. To erase the channels place the ignition in the ON/RUN position and press and hold the two outside HomeLink® buttons (I and III) for up 20 seconds or until the red indicator flashes. NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. Programming A Rolling Code For programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 Training The Garage Door Opener 1 — Door Opener 2 — Training Button 266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to pro- gram while keeping the HomeLink® indicator light in view. 3. Simultaneously press and hold both the HomeLink® button you want to program and the hand-held trans- mitter button. 4. Continue to hold both buttons and observe the indi- cator light. The HomeLink® indicator will flash slowly and then rapidly after HomeLink® has received the frequency signal from the hand-held transmitter. Re- lease both buttons after the indicator light changes from slow to rapid. 5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is attached to the garage door opener/device motor. Firmly press and release the “LEARN” or “TRAIN- ING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 6. Return to the vehicle and press the programmed HomeLink® button twice (holding the button for two seconds each time). If the garage door opener/ device activates, programming is complete. NOTE: If the garage door opener/device does not acti- vate, press the button a third time (for two seconds) to complete the training. To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. Reprogramming A Single HomeLink® Button To reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the ON/RUN position. 2. Press and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “Program- ming A Rolling Code” Step 2 and follow all remaining steps. Programming A Non-Rolling Code For programming Garage Door Openers manufactured before 1995. 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 3. Simultaneously press and hold both the HomeLink® button you want to program and the hand-held trans- mitter button. 4. Continue to hold both buttons and observe the indi- cator light. HomeLink® indicator will flash slowly and then rapidly after HomeLink® has received the frequency signal from the hand-held transmitter. Re- lease both buttons after the indicator light changes from slow to rapid. 5. Press and hold the programmed HomeLink® button and observe the indicator light. • If the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the HomeLink® button is pressed. • To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. 268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink® Button To reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the ON/RUN position. 2. Press and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “Program- ming A Non-Rolling Code” Step 2 and follow all remaining steps. Canadian/Gate Operator Programming For programming transmitters in Canada/United States that require the transmitter signals to “time-out” after several seconds of transmission. Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for HomeLink® to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. 3. Continue to press and hold the HomeLink® button, while you press and release (“cycle”), your hand-held transmitter every two seconds until HomeLink® has successfully accepted the frequency signal. The indi- cator light will flash slowly and then rapidly when fully trained. 4. Watch for the HomeLink® indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming. 5. Press and hold the programmed HomeLink® button and observe the indicator light. • If the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the HomeLink® button is pressed. • To program the two remaining HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 If you unplugged the garage door opener/device for programming, plug it back in at this time. Reprogramming A Single HomeLink® Button To reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the ON/RUN position. 2. Press and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “Canadian/ Gate Operator Programming” Step 2 and follow all remaining steps. and release 270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink® To operate, press the programmed HomeLink® button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink® Universal Transceiver is disabled when the Vehicle Security Alarm is active. Troubleshooting Tips If you are having trouble programming HomeLink®, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the LEARN button on the Garage Door Opener • Did you unplug the device for training, and remember to complete the training for a Rolling Code. to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or as- sistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause unde- sired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not ex- pressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. • The term IC before the certification/registration num- ber only signifies that Industry Canada technical speci- fications were met. 272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch WARNING! • Never leave children in a vehicle with the key in the ignition switch (or with the ignition in the Accessory or On/Run position, for vehicles equipped with Keyless Enter-N-Go™). Occupants, particularly un- attended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passen- gers are also properly secured. • Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. Opening Sunroof — Express Press the switch rearward and release it within one-half second. The sunroof and sunshade will open automati- cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Opening Sunroof — Manual Mode To open the sunroof, press and hold the switch rearward to full open. Any release of the switch will stop the movement. The sunroof and sunshade will remain in a partially opened condition until the switch is pushed and held rearward again. Closing Sunroof — Express Press the switch forward and release it within one- half second and the sunroof will close automatically from any position. The sunroof will close fully and stop UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. Closing Sunroof — Manual Mode To close the sunroof, press and hold the switch in the forward position. Any release of the switch will stop the movement and the sunroof will remain in a partially closed condition until the switch is pushed and held forward again. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. 274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If three consecutive sunroof close attempts re- NOTE: sult in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled. Venting Sunroof — Express Press and release the Vent button within one half second and the sunroof will open to the vent position. This is called “Express Vent”, and it will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof. Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition OFF Operation For Vehicles Not Equipped With The Electronic Vehicle Information Center (EVIC) The power sunroof switch will remain active for 45 sec- onds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. For Vehicles Equipped With The EVIC The power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 ELECTRICAL POWER OUTLETS Your vehicle is equipped with 12 Volt (13 Amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is powered. Power outlets labeled with a “key” are powered when the ignition switch is in the ON or ACC position, while the outlets labeled with a “battery” are connected directly to the battery and powered at all times. NOTE: • All accessories connected to the “battery” powered outlets should be removed or turned off when the vehicle is not in use to protect the battery against discharge. • To ensure proper operation a MOPAR® knob and element must be used. 276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Im- proper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty. The front power outlet is located inside the storage area on the center stack of the instrument panel. Front Power Outlet In addition to the front power outlet, there is also a power outlet located in the storage area of the center console. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 If your vehicle is equipped with a rear full center console, there is also a power outlet located in the lower storage area of the rear full center console. Front Center Console Outlet Rear Full Center Console Outlet 278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear cargo power outlet is located in the right rear cargo area. NOTE: The rear cargo power outlet can be switched to “battery” powered all the time by switching the power outlet right rear quarter panel fuse in the fuse panel. Rear Cargo Power Outlet Power Outlet Right Rear Quarter Panel Fuse UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. Power Outlet Fuse Locations 1 — M7 Fuse 20 A Yellow Power Outlet Right Rear Quarter Panel 2 — M6 Fuse 20 A Yellow Cigar Lighter Front Console 3 — M36 Fuse 20 A Yellow Power Outlet Console Bin POWER INVERTER — IF EQUIPPED There is a 115 Volt, 150 Watt inverter outlet located on the back of the center console to convert DC current to AC current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Play- station3 and XBox360 will exceed this power limit, as will most power tools. 280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly. Only use these intermit- tently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. The power inverter switch is located on the switch bank below the Climate Con- trols. To turn on the power outlet, press the switch once. Press the switch a sec- ond time to turn the power outlet off. Power Inverter The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating NOTE: When the power inverter switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns ON. The status indicator of the AC power inverter indicates whether the inverter is producing AC power. 282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric shock and failure. CUPHOLDERS Front Seat Cupholders There are two cupholders for the front seat passengers located in the center console. Front Cupholder Location Rear Cupholders Rear Center Arm Rest Cupholders — If Equipped There are two cupholders for the rear seat passengers located in the fold-down center armrest. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 Rear Full Console Cupholders — If Equipped There are two cupholders for the rear seat passengers located in the front of the rear full console. Rear Center Arm Rest Cupholders Rear Full Console Cupholders 284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear full console cupholders are equipped with a light ring that illuminates the cupholders for the rear passengers. The light ring is controlled by the Dimmer Control. Refer to “Lights” in “Understanding The Fea- tures Of Your Vehicle” for further information. Rear Mini Console Cupholders — If Equipped There are two cupholders for the rear seat passengers located in the front of the rear mini console. Light Ring In Rear Full Console Cupholders Rear Mini Console Cupholders STORAGE Glove Compartment The glove compartment is located on the right side of the instrument panel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 To open the glove compartment, pull outward on the latch and lower the glove box door. Door Storage Large storage areas are built into the door panels for easy access. Glove Compartment Door Panel Storage 286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Center Console The front center console contains both an upper and a lower storage area. To open the upper storage compartment, pull upward on the small latch located on the lid. Storage Compartment Storage Compartment Latches Lift upward on the larger of the latches to access the lower storage compartment. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 Rear Full Center Console (If Equipped) The rear full center console contains both an upper and a lower storage area. Lower Storage Compartment Storage Compartment 288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper storage compartment, pull upward on the small latch located on the front of the lid. Lift upward on the larger of the latches to access the lower storage compartment. NOTE: Lower storage compartment light is always on with ignition in the ON/RUN position. Upper Storage Compartment Lower Storage Compartment The upper storage compartment may also be lifted for- ward. Push in the release button located on the back of the lid. CAUTION! Remove any items stored in the console cupholders or devices with cords routing through upper storage area. Damage may occur to upper console lid and device cables when upper storage compartment is lifted forward. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 Storage Compartment Rear Push Button 290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When lifted forward there is access to the lower storage compartment. NOTE: When the lower storage compartment is accessed it allows the armrest to flip forward for “fold flat mode”. Fold flat mode allows the console armrest to be lowered below fold flat seat plane and protect the armrest vinyl from damage when using the vehicle to haul cargo. Lower Storage Compartment Fold Flat Mode Open storage areas, or cubby bins with removable liners, are located rearward of the cupholders and in the lower front of the console. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 Rear Mini Center Console (If Equipped) An open storage area, or cubby bin with removable liner, is located in the front of the console. Console Cubby Bins Console Cubby Bin 292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Rechargeable Flashlight The rechargeable flashlight is mounted on the left side of the cargo area. The flashlight snaps out of the bezel when needed. The flashlight features two bright LED light bulbs and is powered by rechargeable lithium batteries that recharge when snapped back into place. Press in on the flashlight to release it. Press And Release To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the pins on the ends of the cover into the slots in the pillar trim cover. 3. The liftgate may be opened with the cargo cover in place. Three-Press Switch Cargo Storage There is a removable storage bin located on the left side of the rear cargo area. Additional storage can be found in the load floor. To access the lower storage, lift the handle and raise the storage lid. 294 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. Do not store it in the vehicle. Cargo Tie-Down Hooks The cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. WARNING! • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes (Continued) only, not for passengers, who should sit in seats and use seat belts. • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or accident, a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in per- sonal injury, follow these guidelines for loading your vehicle: • Do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar. (Continued) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295 REAR WINDOW FEATURES Rear Window Wiper/Washer The rear wiper/washer controls are located on the mul- tifunction lever on the left side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever. WARNING! (Continued) • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as pos- sible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be- come a dangerous projectile in a sudden stop or accident. Rear Wiper/Washer Control 296 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the center portion of the lever upward to the first detent for intermittent operation and to the second detent for continuous rear wiper operation. Rotating the center portion upward once more will activate the washer pump which will con- tinue to operate as long as the switch is held. Upon release of the switch, the wipers will resume the continu- ous rear wiper operation. When this rotary control is in the OFF position, rotating it downward will activate the rear washer pump which will continue to operate as long as the switch is held. Once the switch is released it will return to the OFF position and the wipers will cycle several times before returning to the parked position. NOTE: As a protective measure, the pump will stop if the switch is held for more than 20 seconds. Once the switch is released the pump will resume normal opera- tion. If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “park” position. Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ap- proximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating. CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 297 ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. The crossbars on your vehicle are delivered stowed within the roof rack side rails. Crossbars should always be used whenever cargo is placed on the roof rack. Check the straps frequently to be sure that the load remains securely attached. 298 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deploying the Crossbars Starting with one crossbar, completely loosen the thumb screws at both ends of the crossbar. 1 — Side Rail 2 — Crossbar The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. NOTE: The thumb screws cannot be fully removed. Thumb Screw Remove the crossbar from the stowed position by sliding the crossbar towards the center of the roof. Repeat with crossbar on the opposite side. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 299 CAUTION! Be careful when handling the crossbars to prevent damage to the vehicle. Starting with one crossbar, bend down the pivot supports at each end. Removing Crossbars Bending Pivot 300 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position the crossbars across the roof making sure the letters on the crossbars align with the matching letters on the side rail. crossbar is fully deployed with the crossbar pushed as far into the slot as possible. Once the crossbar is in place, tighten both thumb screws completely. Positioning Crossbars Installing Crossbars Slide the cross bar into to the deploy position by moving it towards the matching letter in the side rail. Be sure the Deploy and tighten the second crossbar to complete the deployment of the crossbars. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 301 CAUTION! Be careful when handling the crossbars to prevent damage to the vehicle. Starting with the one crossbar, bend up the pivot sup- ports at each end. Deployed Crossbars Stowing the Crossbars Starting with one crossbar, completely loosen the thumb screws at both ends. Slide the crossbar away from the matching letter to remove it from the deployed position. Repeat with the other crossbar. Crossbar Pivot 302 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then, position the crossbar along the correct side rail. Make sure the letters on the crossbar align with the matching letters on the side rail. Slide the crossbar outward, away from the center of the roof. The crossbar will nest fully within the side rail. Stowing Crossbars Crossbar To Side Rail Once the driver’s side crossbar is in place, tighten the thumb screws completely. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 303 Repeat the procedure to stow the second crossbar on the opposite side. Tightening Crossbar Stowed Crossbars 304 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • To help control wind noise, stow the crossbars in the • If any metallic object is placed over the satellite radio antenna (if equipped), you may experience interrup- tion of satellite radio reception. side rails when they are not in use. CAUTION! • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without the crossbars deployed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or other protective layer between the load and the roof surface. (Continued) CAUTION! (Continued) • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lb (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately. • Load should always be secured to cross bars first, with tie down loops used as additional securing points if needed. Tie loops are intended as supple- mentary tie down points only. Do not use ratchet- ing mechanisms with the tie loops. Check the straps and thumbwheels frequently to be sure that the load remains securely attached. • Long loads that extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. (Continued) CAUTION! (Continued) • Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 305 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack. UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .311 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . ..312 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . ..313 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) ▫ Electronic Vehicle Information Center (EVIC) . . . . . . . . . . . . . . . . . . . . . . .324 Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . .326 ▫ EVIC White Telltale Lights . . . . . . . . . . . . . ..332 ▫ EVIC Amber Telltale Lights . . . . . . . . . . . . ..333 ▫ EVIC Red Telltale Lights . . . . . . . . . . . . . . ..333 ▫ Engine Oil Change Indicator System . . . . . . ..336 ▫ Fuel Economy . . . . . . . . . . . . . . . . . . . . . . . .337 ▫ Vehicle Speed . . . . . . . . . . . . . . . . . . . . . . . .339 ▫ Trip Info . . . . . . . . . . . . . . . . . . . . . . . . . . .339 ▫ Vehicle Info (Customer Information Features) . .340 ▫ Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 ▫ Keyless Enter-N-Go™ Display — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .341 ▫ Messages # . . . . . . . . . . . . . . . . . . . . . . . . . .341 ▫ Turn Menu OFF. . . . . . . . . . . . . . . . . . . . . . .341 308 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Compass / Temperature Display . . . . . . . . ..341 ▫ Customer-Programmable Features (System Setup) . . . . . . . . . . . . . . . . . . . . . . .344 ▫ System Status . . . . . . . . . . . . . . . . . . . . . . . .353 䡵 Uconnect® 730N/430/430N CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . ..354 ▫ Operating Instructions (Voice Command System) — If Equipped . . . . . . . . . . . . . . . ..354 ▫ Operating Instructions (Uconnect® Phone) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .354 䡵 Uconnect® 130 . . . . . . . . . . . . . . . . . . . . . . . . .355 ▫ Operating Instructions — Radio Mode. . . . . ..355 ▫ Operation Instructions — CD MODE For CD And MP3 Audio Play . . . . . . . . . . . . . . ..358 ▫ Notes on Playing MP3 Files . . . . . . . . . . . . ..360 ▫ Operation Instructions - Auxiliary Mode . . . ..364 䡵 Uconnect® 130 WITH SATELLITE RADIO . . . ..364 ▫ Operating Instructions — Radio Mode. . . . . ..364 ▫ Operation Instructions — CD MODE for CD and MP3 Audio Play . . . . . . . . . . . . . . ..370 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . ..372 ▫ LIST Button (CD Mode for MP3 Play) . . . . . ..375 ▫ INFO Button (CD Mode for MP3 Play) . . . . ..375 ▫ Operating Instructions (Uconnect® Phone) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .376 ▫ Uconnect® Multimedia (Satellite Radio) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .376 䡵 iPod®/USB/MP3 CONTROL — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .381 ▫ Connecting The iPod® Or External USB Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .381 ▫ Using This Feature. . . . . . . . . . . . . . . . . . . ..382 ▫ Controlling The iPod® Or External USB Device Using Radio Buttons . . . . . . . . . . . . . . . . . ..383 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . .383 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . ..384 ▫ Bluetooth Streaming Audio (BTSA) . . . . . . . ..386 䡵 UCONNECT® MULTIMEDIA — VIDEO ENTERTAINMENT SYSTEM (VES)™ — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . . . . .388 ▫ Getting Started . . . . . . . . . . . . . . . . . . . . . . .388 ▫ Single Video Screen . . . . . . . . . . . . . . . . . . ..388 UNDERSTANDING YOUR INSTRUMENT PANEL 309 ▫ Play Video Games . . . . . . . . . . . . . . . . . . . ..392 ▫ Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1. . . . ..394 ▫ Important Notes For Single Video Screen System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .396 ▫ Play A DVD Using The Touch-Screen Radio . . .396 ▫ VES Remote Control – If Equipped . . . . . . . ..399 ▫ Remote Control Storage . . . . . . . . . . . . . . . ..402 ▫ Locking The Remote Control . . . . . . . . . . . ..403 ▫ Replacing The Remote Control Batteries. . . . ..403 ▫ Headphones Operation . . . . . . . . . . . . . . . ..404 ▫ Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .405 ▫ Replacing The Headphone Batteries. . . . . . . ..406 310 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Unwired® Stereo Headphone Lifetime Limited Warranty . . . . . . . . . . . . . . . . . . . ..406 ▫ System Information . . . . . . . . . . . . . . . . . . ..407 䡵 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .423 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .424 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . .424 䡵 CD/DVD DISC MAINTENANCE . . . . . . . . . ..425 䡵 RADIO OPERATION AND MOBILE PHONES . .425 䡵 CLIMATE CONTROLS . . . . . . . . . . . . . . . . . ..426 ▫ Dual-Zone Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . ..426 ▫ Rear Climate Control — If Equipped . . . . . ..432 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . .435 ▫ Window Fogging . . . . . . . . . . . . . . . . . . . ..435 ▫ Summer Operation . . . . . . . . . . . . . . . . . . ..435 ▫ Winter Operation. . . . . . . . . . . . . . . . . . . . . .436 ▫ Vacation Storage . . . . . . . . . . . . . . . . . . . . . .436 ▫ Operating Tips Chart . . . . . . . . . . . . . . . . . ..437 INSTRUMENT PANEL FEATURES UNDERSTANDING YOUR INSTRUMENT PANEL 311 1 — Air Outlet 2 — Instrument Cluster 3 — Radio 4 — Glove Compartment 5 — Climate Controls 6 — Lower Switch Bank 7 — Hazard Switch 8 — Storage Bin 9 — ESC Off Switch 10 — Ignition Switch 11 — Headlight Switch 12 — Hood Release 13 — Fuel Door Release 14 — Dimmer Control 312 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER INSTRUMENT CLUSTER DESCRIPTIONS 1. Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000). 2. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) UNDERSTANDING YOUR INSTRUMENT PANEL 313 As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. 314 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result. 3. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called OBD II that monitors engine and automatic transmission con- trol systems. The light will illuminate when the key is in the ON/RUN position before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing. UNDERSTANDING YOUR INSTRUMENT PANEL 315 CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 316 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Electronic Stability Control Malfunction Indicator Light — If Equipped (ESC) Activation/ The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running. If the “ESC Activation/Malfunction In- dicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. NOTE: The “ESC Off Indicator Light” and the “ESC Activation/ Malfunction Indicator Light” come on momentarily each time the ignition switch is turned to ON/RUN. Each time the ignition is turned to ON/RUN, the ESC system will be ON, even if it was turned off previously. The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation. 5. Electronic Stability Control Light — If Equipped (ESC) OFF Indicator This light indicates the Electronic Stability Con- trol (ESC) is off. 6. Anti-Lock Brake (ABS) Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the ignition switch is turned to the ON/RUN position, have the light inspected by an authorized dealer. 7. Front Fog Light Indicator — If Equipped This indicator will illuminate when the front fog lights are on. 8. Park/Headlight ON Indicator — If Equipped This indicator will illuminate when the park lights or headlights are turned on. UNDERSTANDING YOUR INSTRUMENT PANEL 317 9. Turn Signal Indicator The arrows will flash with the exterior turn sig- nals when the turn signal lever is operated. A tone will chime, and an EVIC message will appear if either turn signal is left on for more than 1 mile (1.6 km). NOTE: If either indicator flashes at a rapid rate, check for a defective outside light bulb. 10. High Beam Indicator This light indicates that the headlights are on high beam. Pull the turn signal lever toward the steer- ing wheel to switch the headlights to low beam. 11. Electronic Vehicle Information Center (EVIC) Red Telltale Area This area will display the EVIC reconfigurable red tell- tales. For further information, refer to “Electronic vehicle Information Center (EVIC)”. (EVIC) 318 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Electronic Vehicle Information Center Display/Odometer Display The odometer display shows the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero. When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages. Refer to “Electronic Vehicle Information Center”. 13. Electronic Vehicle Information Center (EVIC) White Telltale Area This area will display the EVIC reconfigurable white telltales. For further information, refer to “Electronic vehicle Information Center (EVIC)”. 14. 4 LOW — If Equipped This light alerts the driver that the vehicle is in the four-wheel drive LOW mode. The front and rear driveshafts are mechanically locked to- gether forcing the front and rear wheels to rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels. For further information on four-wheel drive operation and proper use, refer to “Four-Wheel Drive Operation — If Equipped” in “Starting And Operating”. 15. Hill Descent Indicator — If Equipped 19. Air Bag Warning Light UNDERSTANDING YOUR INSTRUMENT PANEL 319 The symbol illuminates (is armed) when the 4WD Lock switch is activated and the trans- mission range indicator is in LOW or REVERSE position (Off-Road Mode). 16. Speedometer Indicates vehicle speed. 17. Fuel Door Reminder The fuel pump symbol points to the side of the vehicle where the fuel door is located. 18. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position. This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to the ON/RUN position. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an autho- rized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. 20. Adaptive Cruise Control (ACC) Malfunction This light will turn on when a ACC is not operating and needs service. For further infor- mation, refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle.” 320 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Adaptive Cruise Control (ACC) SET This light will turn on when a ACC has been SET. For further information, refer to “Adap- tive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle.” 22. Adaptive Cruise Control (ACC) ON This light will turn on when a ACC is ON. For further information, refer to “Adaptive Cruise Control (ACC)” in “Understanding The Fea- tures Of Your Vehicle.” 23. Electronic Speed Control Light SET This light will turn on when the electronic speed control is SET. For further information, refer to “Electronic Speed Control” in “Under- standing The Features Of Your Vehicle.” 24. Electronic Speed Control ON This light will turn on when the electronic speed control is ON. For further information, refer to “Electronic Speed Control” in “Under- standing The Features Of Your Vehicle.” 25. Electronic Vehicle Information Center (EVIC) Amber Telltale Area This area will display the EVIC reconfigurable amber caution telltales. For further information, refer to “Elec- tronic vehicle Information Center (EVIC)”. 26. Vehicle Security Light This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set. The security light will also come on for about three seconds when the ignition is first turned on. 27. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. UNDERSTANDING YOUR INSTRUMENT PANEL 321 The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary. 322 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 28. TOW/HAUL The TOW HAUL button is located on the center stack upper switch bank. This light will illumi- nate when TOW HAUL mode is selected 29. Seat Belt Reminder Light When the ignition switch is first turned to the ON/RUN position, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Indicator Light will flash or remain on continuously. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. 30. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. UNDERSTANDING YOUR INSTRUMENT PANEL 323 The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an autho- rized dealer for service. 324 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the instrument cluster. The EVIC consists of the following: • System Status • Vehicle Information Warning Message Displays • Customer-Programmable Features (System Setup) • Compass Display • Outside Temperature Display • Trip Computer Functions The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: EVIC Steering Wheel Buttons UNDERSTANDING YOUR INSTRUMENT PANEL 325 • UP Button Press and release the UP button to scroll up- ward through the main menus (Fuel Economy, ACC (if equipped), Vehicle Speed, Trip Info, Vehicle Info, Tire PSI, Messages, Units, System Setup, Turn Menu Off) and sub-menus. • DOWN Button Press and release the DOWN button to scroll downward through the main menus and sub-menus. • SELECT Button Press and release the SELECT button for access to main menus, sub-menus or to select a per- sonal setting in the setup menu. Hold the select button to use the RESET function. For example, while in the Fuel Economy page, hold and release the select button to reset the AVG. 326 UNDERSTANDING YOUR INSTRUMENT PANEL • BACK Button Press the BACK button to scroll back to a previous menu or sub-menu. Electronic Vehicle Information Center (EVIC) Displays The EVIC display consists of three sections: 1. The top line where compass direction, odometer line and outside temperature are displayed. 2. The main display area where the menus and pop up messages are displayed. 3. The reconfigurable telltales section below the odom- eter line. The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warning or infor- mation messages. These pop up messages fall into several categories: • Five Second Stored Messages When the appropriate conditions occur, this type of mes- sage takes control of the main display area for five seconds and then returns to the previous screen. Most of the messages of this type are then stored (as long as the condition that activated it remains active) and can be reviewed from the “Messages”main menu item. As long as there is a stored message, an “i” will be displayed in the EVIC’s compass/outside temp line. Examples of this mes- sage type are “Right Front Turn Signal Lamp Out” and “Low Tire Pressure”. • Unstored Messages This message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are “Turn Signal On” (if a turn signal is left on) and “Lights On” (if driver leaves the vehicle). • Unstored Messages Until RUN These messages deal primarily with the Remote Start feature. This message type is displayed until the ignition is in the RUN state. Examples of this message type are “Remote Start Aborted - Door Ajar” and “Press Brake Pedal and Push Button to Start”. • Five Second Unstored Messages When the appropriate conditions occur, this type of mes- sage takes control of the main display area for five seconds and then returns to the previous screen. Examples of this message type are “Memory System Unavailable - Not in Park” and “Automatic High Beams On”. The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left. UNDERSTANDING YOUR INSTRUMENT PANEL 327 When the appropriate conditions exist, the EVIC displays the following messages: • Vehicle Not in Park • Key Left Vehicle • Key Not Detected • Press Brake Pedal and Push Button to Start • Premium TPM System Graphic Display • Service TPM System (refer to “Tire Pressure Monitor- • Service Keyless System (refer to Keyless Enter-N-Go™, Passive Entry - if equipped) • Service Park Assist System ing System” in “Starting And Operating”) 328 UNDERSTANDING YOUR INSTRUMENT PANEL • Park Assist System Blinded • Keyfob Battery Low • Left front turn signal lamp out • Right front turn signal lamp out • Left rear turn signal lamp out • Right rear turn signal lamp out • Service air filter • Low Tire Pressure • Perform service • ESC System Off • Service blind spot system • Blind spot detection unavailable • Blind spot system off • Blind spot detection unavailable sensor blocked • Normal Cruise Ready — When Adaptive Cruise Con- trol (ACC) system is turned off and Normal (Fixed Speed) Cruise Control mode is available. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if equipped). • Adaptive Cruise Off — When the Adaptive Cruise Control (ACC) system is turned off. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Fea- tures Of Your Vehicle” (if equipped). • ACC Ready — When the ACC system is activated. Refer to “Adaptive Cruise Control (ACC)” in “Under- standing The Features Of Your Vehicle” (if equipped). • ACC Set — After setting the desired speed in the ACC system. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if equipped). • ACC Cancelled — To disable the ACC system. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if equipped). • Sensed Vehicle Indicator — The system detects a slower moving vehicle in the same lane. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if equipped). • Driver Override — If you apply the accelerator after setting the desired speed in the ACC system. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if equipped). • Distance Set — After changing the desired following distance in the ACC system, this message will display momentarily. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Ve- hicle” (if equipped). UNDERSTANDING YOUR INSTRUMENT PANEL 329 • Brake — If the ACC system predicts that its maximum braking level is not sufficient to maintain the set dis- tance, this message will flash and a chime will sound while ACC continues to apply its maximum braking capacity. When this occurs, you should immediately apply the brakes as needed to maintain a safe distance from the vehicle ahead. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if equipped). • Clean Radar Sensor in the Front of Vehicle — If the ACC system deactivates due to performance limiting conditions. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if equipped). • ACC/FCW Unavailable Vehicle System Error — If the ACC system turns off due to a temporary malfunction that limits functionality. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if equipped). 330 UNDERSTANDING YOUR INSTRUMENT PANEL • ACC/FCW Unavailable Service Radar Sensor — If the ACC system turns off due to an internal system fault that requires service from an authorized dealer. Refer to “Adaptive Cruise Control (ACC)” in “Understand- ing The Features Of Your Vehicle” (if equipped). • Cruise Off When Park Brake is On • ACC Cancelled Below Min. Speed • Coolant low • Oil change due > Dealer Info • Key in ignition • Lights on • Key in Ignition Lights On • Ignition or Accessory On • Ignition or Accessory On Lights On • Oil temp high Speed may be limited • Oil temp high Speed limited • Turn signal on • Park assist on • Warning object detected • Remote start aborted — Door ajar • Remote start aborted — Hood ajar • Remote start aborted — L/Gate ajar • Remote start aborted — Fuel low • Remote start disabled — Start Vehicle to Reset • Remote start active — Push Start Button • Remote start active — Insert Key and Turn to Run • Memory 1 profile set • Memory 2 profile set • Memory system unavailable — Not in Park • Memory system unavailable — Seatbelt buckled • Memory 1 profile recall • Memory 2 profile recall • Wrong Key • Damaged Key • Key not programmed • Park Assist Disabled • Automatic high beams on UNDERSTANDING YOUR INSTRUMENT PANEL 331 Owners Manual • Automatic high beams off • Service All Wheel Drive System • All Wheel Drive System in neutral • ECO — Fuel Saver Indicator • To Tow Vehicle Safely, Read Neutral Shift Procedure in • AWD AUTO • LOW RANGE • SERV AWD • For AWD Low Slow Below 5 MPH or 8 KPH Put Trans • For AWD High Slow Below 5 MPH or 8 KPH Put Trans in N Press 4 Low in N Press 4 Low 332 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC White Telltale Lights This area will show reconfigurable white caution tell- tales. These telltales include: • Shift Lever Status The shift lever status “P, R, N, D, L, 5, 4, 3, 2, 1” are displayed indicating the shift lever position. Telltales “5, 4, 3, 2, 1” indicate the Electronic Range Select (ERS) feature has been engaged and the gear selected is dis- played. For further information on ERS, refer to “Starting And Operating”. • Power Steering System Over Temperature — If Equipped If the “POWER STEERING SYSTEM OVER TEMP” message and a icon are displayed on the EVIC screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system. You will lose power steering assistance momentarily until the over temperature condition no longer exists. Once driving conditions are safe, then pull over and let vehicle idle. After five minutes, the system will cool and return to normal operation. Refer to “Power Steering” in “Starting and Operating” for further information. NOTE: • Even if power steering assistance is no longer opera- tional, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. • If the condition persists, see your authorized dealer for service. EVIC Amber Telltale Lights This area will show reconfigurable amber caution tell- tales. These telltales include: • Low Fuel Light When the fuel level reaches approximately 3.0 gal (11.0 L) this light will turn on, and remain on until fuel is added. • Loose Gascap Indicator If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the telltale display area. Tighten the fuel filler cap properly and press the SELECT button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL). UNDERSTANDING YOUR INSTRUMENT PANEL 333 • Windshield Washer Fluid Low Indicator This light will turn on to indicate the wind- shield washer fluid is low. • SERV AWD The SERV AWD light monitors the electric shift AWD system. If the SERV AWD light stays on or comes on during driving, it means that the AWD system is not functioning properly and that service is required. EVIC Red Telltale Lights This area will show reconfigurable red telltales. These telltales include: • Door Ajar This light will turn on to indicate that one or more doors may be ajar. 334 UNDERSTANDING YOUR INSTRUMENT PANEL • Liftgate Ajar • Charging System Light This light will turn on to indicate that liftgate may be ajar. • Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. This light shows the status of the electrical charg- ing system. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an autho- rized dealer. If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. • Electronic Throttle Control (ETC) Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an authorized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • Engine Temperature Warning Light This light warns of an overheated engine condition. As temperatures rise and the gauge approaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H, the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool. UNDERSTANDING YOUR INSTRUMENT PANEL 335 If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for more information. • Transmission Temperature Warning Light This light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.g., snow plowing, off- road operation). If this light comes on, stop the vehicle and run the engine at idle or faster, with the transmission in NEUTRAL until the light goes off. 336 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Continuous driving with the Transmission Tempera- ture Warning Light illuminated will eventually cause severe transmission damage or transmission failure. WARNING! If you continue operating the vehicle when the Transmission Temperature Warning Light is illumi- nated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. Engine Oil Change Indicator System Oil Change Due Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Due” message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded, to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position or cycle the ignition to the ON/RUN position if equipped with Keyless Enter-N-Go™. To turn off the message temporarily, press and release the MENU but- ton. To reset the oil change indicator system (after performing the scheduled maintenance) refer to the fol- lowing procedure. Vehicles Equipped With Keyless Enter-N-Go™ 1. Without pressing the brake pedal, cycle the ignition to the ON/RUN position (Do not start the engine.) 2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Cycle the ignition to the OFF/LOCK position. Vehicles Not Equipped With Keyless Enter-N-Go™ 1. Turn the ignition switch to the ON/RUN position (Do not start the engine.) 2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to the OFF/LOCK position. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. UNDERSTANDING YOUR INSTRUMENT PANEL 337 Fuel Economy Press and release the UP/DOWN buttons until one of the following Fuel Economy Functions displays in the EVIC: • Average Fuel Economy/Fuel Saver Mode • Distance To Empty Average Fuel Economy/Fuel Saver Mode — If Equipped This feature shows the average fuel economy since the last reset. To reset the average fuel economy display, press and release the SELECT button once while average fuel economy is highlighted. Once reset, the history information will be erased, and the averaging will con- tinue from the last fuel average reading before the reset. The FUEL SAVER MODE message will display above the average fuel economy in the EVIC display. This message will appear whenever the Multi-Displacement System 338 UNDERSTANDING YOUR INSTRUMENT PANEL (MDS) (if equipped) allows the engine to operate on four cylinders, or if you are driving in a fuel efficient manner. Fuel Saver Mode — On This feature allows you to monitor when you are driving in a fuel efficient manner, and it can be used to modify driving habits in order to increase fuel economy. Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the SELECT button. NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a “LOW FUEL” message. This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the “LOW FUEL” message and a new DTE value will display. Vehicle Speed This feature allows you to monitor your vehicle speed on the EVIC display, press and release the SELECT button to change the units of measure between in MPH or km/h. Trip Info This feature allows you to track the total distance trav- eled since the last reset and the elapsed time of travel. Press and release the UP/DOWN buttons until one of the following Trip Functions displays in the EVIC: • Trip A • Trip B • Elapsed Time UNDERSTANDING YOUR INSTRUMENT PANEL 339 Press the UP/DOWN buttons to cycle through all the Trip Computer functions. The Trip Functions mode dis- plays the following information: Trip A Shows the total distance traveled for Trip A since the last reset. Trip B Shows the total distance traveled for Trip B since the last reset. Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position. 340 UNDERSTANDING YOUR INSTRUMENT PANEL To Reset The Display Press and release the UP or DOWN button until “Vehicle Info” displays in the EVIC and press the SELECT button. Press the UP and DOWN button to scroll through the available information displays, then press SELECT to display any one of the following choices. Vehicle Info (Customer Information Features) Press and release the UP or DOWN button until “Vehicle Info” displays in the EVIC and press the SELECT button. Press the UP and DOWN button to scroll through the available information displays, then press SELECT to display any one of the following choices. • Coolant Temp Displays the actual coolant temperature. • Oil Temperature Displays the actual oil temperature. • Oil Pressure Displays the actual oil pressure. • Trans Temperature Displays the actual transmission temperature. • Engine Hours Displays the number of hours of engine operation. Units Press and release the UP or DOWN button until “Units” displays in the EVIC and press the SELECT button. The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of mea- sure. To make your selection, press and release the SELECT button the selected setting will be displayed. Keyless Enter-N-Go™ Display — If Equipped When the ENGINE START/STOP button is pressed to change ignition switch positions, the Keyless Enter-N- Go™ icon momentarily appears in the lower right corner of the EVIC display showing the new ignition switch position. Refer to “Keyless Enter-N-Go™” in “Starting And Oper- ating” for more information. NOTE: Under certain conditions, the display may be superseded by another display of higher priority. But when the ignition switch position is changed, the display always re-appears. Messages # Select from Main Menu using the UP or DOWN buttons. This feature shows the number of stored warning messages UNDERSTANDING YOUR INSTRUMENT PANEL 341 (in the # place holder). Pressing the SELECT button will allow you to see what the stored messages are. Press and release the UP and DOWN buttons if there is more than one message to step through the remaining stored mes- sages. Pressing the BACK button takes you back to the Main Menu. Turn Menu OFF Select from Main Menu using the DOWN button. Press- ing the SELECT button blanks the menu display. Pressing any one of the four steering wheel buttons brings the menu back. Compass / Temperature Display The compass readings indicate the direction the vehicle is facing. The EVIC will display one of eight compass readings and the outside temperature. 342 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated tempera- ture is displayed. Engine temperature can also affect the displayed temperature; therefore, temperature readings are not updated when the vehicle is not moving. Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to manually reset the compass. When the vehicle is new, the compass may appear erratic and the EVIC will display CAL until the compass is calibrated. You may also calibrate the compass by completing one or more 360–degree turns (in an area free from large metal or metallic objects) until the CAL indicator displayed in the EVIC turns off. The compass will now function normally. NOTE: A good calibration requires a level surface and an environment free from large metallic objects such as build- ings, bridges, underground cables, railroad tracks, etc. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences, and provide the most accurate compass heading. For the most accurate compass performance, the compass must be set using the following steps. NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Laptops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. UNDERSTANDING YOUR INSTRUMENT PANEL 343 3. Press the DOWN button until the “Compass Variance” message is displayed in the EVIC, then press the SELECT button. The last variance zone number dis- plays in the EVIC. 4. Press and release the SELECT button until the proper variance zone is selected, according to the map. 5. Press and release the BACK button to exit. Manual Compass Calibration If the compass appears erratic and the CAL indicator does not appear in the EVIC display, you must put the compass into the Calibration Mode manually, as follows: NOTE: For the most accurate compass performance, the compass variance must be set before performing the manual compass calibration. The variance should be set for the zone where the vehicle is driven, per the zone map. For further information, refer to “Compass Variance.” Compass Variance Map 1. Turn the ignition switch ON. 2. Press the UP or DOWN button until the Setup (Customer-Programmable Features) menu is reached, then press the SELECT button. 344 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Turn ON the ignition switch. 2. Press the UP or DOWN button until the Setup (Customer-Programmable Features) menu is reached, then press the SELECT button. 3. Press the DOWN button until “Calibrate Compass” is displayed in the EVIC. 4. Press and release the SELECT button to start the calibration. The “CAL” indicator will be displayed in the EVIC. 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Customer-Programmable Features (System Setup) Personal Settings allows you to set and recall features when the transmission is in PARK. If the transmission is out of PARK or the vehicle begins moving, a warning message SETUP NOT AVAILABLE, is followed in 3 sec- onds by, VEHICLE NOT IN PARK. Press and release the UP or DOWN button until Setup displays in the EVIC. Use the UP or DOWN button to display one of the following choices. Select Language When in this display you may select one of five lan- guages for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the UP or DOWN button while in this display and scroll through the language choices. Press the SELECT button to select English, Spanish (Español), French (Français), Italian (Italiano), German (Deutsch), and Dutch (Neder- lands). Then, as you continue, the information will dis- play in the selected language. Nav–Turn By Turn When this feature is selected the navigation system utilizes voice commands, guiding you through the drive route mile by mile, turn-by-turn until the final destina- tion is reached. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated. Auto Unlock Doors When this feature is selected, all doors will unlock when the vehicle is stopped and the transmission is in the PARK or NEUTRAL position and the driver’s door is UNDERSTANDING YOUR INSTRUMENT PANEL 345 opened. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated. Remote Unlock Sequence When Unlock Driver Door Only On 1st Press is selected, only the driver’s door will unlock on the first press of the RKE transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When Unlock All Doors On 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button. To make your selection, scroll up or down until the preferred setting is high- lighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected. 346 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the vehicle is equipped with passive entry and the EVIC is programmed to Unlock All Doors 1st Press, all doors will unlock no matter which passive entry equipped door handle is grasped. If Driver Door 1st Press

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2013 Dodge Durango Owners Manual