2013 Dodge Durango Owners Manual

Download PDF Manual
facturer also allows contact. In positions with cinching latch plates (CINCH), the buckle stalk may be twisted up to 3 full turns. Do not twist the buckle stalk in a seating position with an ALR retractor. 104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint with a Switchable Automatic Locking Retractor (ALR) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path. 3. Slide the latch plate into the buckle until you hear a “click.” 4. Pull on the webbing to make the lap portion tight against the child seat. 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode. 6. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any web- bing. If the retractor is not locked, repeat step 5. 7. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat. 8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “Lower Anchors and Tethers for Chil- dren (LATCH) Restraint System” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. Installing A Child Restraint With A Cinching Latch Plate (CINCH) — If Equipped 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and / or raise the head restraint to get a better fit. 2. Next, pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 3. Slide the latch plate into the buckle until you hear a “click.” 4. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat. 5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “Lower Anchors and Tethers for Chil- dren (LATCH) Restraint System” for directions to attach a tether anchor. 6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. 106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have trouble tightening the seat belt. If this happens, discon- nect the latch plate from the buckle and twist the short buckle-end belt up to three full turns to shorten it. Insert the latch plate into the buckle with the release button facing out, away from the child restraint. Repeat steps 4 to 6, above, to complete the installation of the child restraint. If the belt still cannot be tightened after you shorten the buckle, disconnect the latch plate from the buckle, turn the buckle around one half turn, and insert the latch plate into the buckle again. If you still cannot make the child restraint installation tight, try a different seating position. Installing Child Restraints Using The Top Tether Anchorage 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position (see the charts above), move the child restraint to another position in the vehicle if one is available. 2. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchor- ages. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 Pulling Down The Carpet Floor Panel To Access Top Tether Strap Top Tether Strap Anchorage (Located on Seatback) 108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 4. For the center seating position, route the tether strap over the seatback and headrest then attach the hook to the tether anchor located on the back of the seat. 5. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. Top Tether Strap Mounting (60/40 Seat) THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 WARNING! The top tether anchorages are not visible until the gap panel is folded down. Do not use the visible cargo tie down hooks, located on the floor behind the seats, to attach a child restraint tether anchor. Installing Child Restraints Using The Top Tether Anchorage — Center Seating Position For center seating position route the tether strap over the seatback and headrest then attach the hook to the tether anchor located on the back of the seat. Transporting Pets Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. Top Tether Strap Mounting (Captain’s Chair) 6. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. 110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recom- mended viscosity and quality grades, refer to “Mainte- nance Procedures” in “Maintaining Your Vehicle”. CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. • If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. • If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. 112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Air Bag Warning Light The light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. WARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor cover- ings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. (Continued) THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 WARNING! (Continued) • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals. • Check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal and accel- erator pedal causing a loss of vehicle control. • If required, mounting posts must be properly in- stalled, if not equipped from the factory. Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle. 114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure. Lights Have someone observe the operation of brake lights and exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately. UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . ..122 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .122 ▫ Automatic Dimming Mirror — If Equipped . . .123 ▫ Outside Mirrors Folding Feature . . . . . . . . ..124 ▫ Outside Automatic Dimming Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .124 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . .124 ▫ Heated Mirrors — If Equipped . . . . . . . . . ..125 ▫ Tilt Mirrors In Reverse (Available With Memory Seat Only) — If Equipped . . . . . . . . . . . . . ..125 ▫ Illuminated Vanity Mirrors . . . . . . . . . . . . ..126 ▫ Sun Visor Extension — If Equipped . . . . . . ..126 䡵 BLIND SPOT MONITORING — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .127 ▫ Rear Cross Path . . . . . . . . . . . . . . . . . . . . . .132 ▫ Modes Of Operation . . . . . . . . . . . . . . . . . ..134 䡵 Uconnect® Phone — IF EQUIPPED . . . . . . . . ..135 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .137 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Phone Call Features . . . . . . . . . . . . . . . . . . ..144 ▫ Uconnect® Phone Features . . . . . . . . . . . . . ..147 ▫ Advanced Phone Connectivity . . . . . . . . . . ..152 ▫ Things You Should Know About Your Uconnect® Phone . . . . . . . . . . . . . . . . . . . ..154 ▫ General Information . . . . . . . . . . . . . . . . . ..165 䡵 VOICE COMMAND — IF EQUIPPED . . . . . ..165 ▫ Voice Command System Operation . . . . . . . ..165 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . . .167 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . . .171 䡵 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 ▫ Power Seats — If Equipped . . . . . . . . . . . . ..172 ▫ Passenger’s Power Seat — If Equipped . . . . ..174 ▫ Power Lumbar — If Equipped . . . . . . . . . . ..174 ▫ Manual Front Passenger Seat Forward/ Rearward Adjustment . . . . . . . . . . . . . . . . ..175 ▫ Manual Front Passenger Seatback Adjustment — Recline . . . . . . . . . . . . . . . ..176 ▫ Front Passenger Seat Fold-Flat Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .177 ▫ Heated Seats — If Equipped . . . . . . . . . . . . ..177 ▫ Ventilated Seats — If Equipped . . . . . . . . . . ..180 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . . .181 ▫ 60/40 Split Rear Seat . . . . . . . . . . . . . . . . ..186 ▫ Rear Captain Chairs — If Equipped. . . . . . . ..189 ▫ Folding Third Row . . . . . . . . . . . . . . . . . . ..192 䡵 DRIVER MEMORY SEAT — IF EQUIPPED . . . .194 ▫ Programming The Memory Feature . . . . . . . ..195 ▫ Linking And Unlinking The Remote Keyless Entry Transmitter To Memory . . . . . . . . . . . ..196 ▫ Memory Position Recall . . . . . . . . . . . . . . . ..197 ▫ Easy Entry/Exit Seat . . . . . . . . . . . . . . . . . ..198 䡵 TO OPEN AND CLOSE THE HOOD . . . . . . . ..200 䡵 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 ▫ Headlight Switch . . . . . . . . . . . . . . . . . . . ..201 ▫ Automatic Headlights — If Equipped . . . . . ..202 ▫ Headlights On Automatically With Wipers . . .202 ▫ SmartBeam™ — If Equipped . . . . . . . . . . . ..203 ▫ Daytime Running Lights — If Equipped . . . ..204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 ▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . .204 ▫ Parking Lights And Panel Lights. . . . . . . . . ..205 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . ..205 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . . .206 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . ..207 ▫ Battery Saver. . . . . . . . . . . . . . . . . . . . . . . . .207 ▫ Front Map/Reading Lights . . . . . . . . . . . . ..207 ▫ Courtesy Lights . . . . . . . . . . . . . . . . . . . . . . .262 ▫ Ambient Light. . . . . . . . . . . . . . . . . . . . . . . .209 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . ..209 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . .210 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . ..210 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . .210 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ High/Low Beam Switch. . . . . . . . . . . . . . . ..210 䡵 WINDSHIELD WIPERS AND WASHERS . . . . ..210 ▫ Windshield Wiper Operation. . . . . . . . . . . . . .211 ▫ Intermittent Wiper System . . . . . . . . . . . . . ..212 ▫ Windshield Washer Operation. . . . . . . . . . . ..212 ▫ Mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213 ▫ Rain Sensing Wipers — If Equipped . . . . . . ..214 䡵 TILT/TELESCOPING STEERING COLUMN . . .216 䡵 POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED . . . . . . . . . . . . . ..217 䡵 HEATED STEERING WHEEL — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .218 䡵 ELECTRONIC SPEED CONTROL . . . . . . . . . ..219 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . .220 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . ..220 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .220 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . ..221 ▫ To Vary The Speed Setting . . . . . . . . . . . . . ..221 ▫ To Accelerate For Passing . . . . . . . . . . . . . . ..221 䡵 ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .222 ▫ Adaptive Cruise Control (ACC) Operation . . . .224 ▫ Activating Adaptive Cruise Control (ACC). . . .225 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . .226 ▫ To Set A Desired ACC Speed . . . . . . . . . . . ..227 ▫ To Cancel . . . . . . . . . . . . . . . . . . . . . . . . . . .228 ▫ To Turn Off . . . . . . . . . . . . . . . . . . . . . . . . . .229 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . ..229 ▫ To Vary The Speed Setting . . . . . . . . . . . . . ..230 ▫ Setting The Following Distance In ACC . . . . ..231 ▫ Adaptive Cruise Control (ACC) Menu . . . . . ..234 ▫ Display Warnings And Maintenance . . . . . . ..236 ▫ Precautions While Driving With ACC . . . . . ..239 ▫ General Information . . . . . . . . . . . . . . . . . ..243 ▫ Normal (Fixed Speed) Cruise Control Mode . . .243 ▫ Forward Collision Warning — If Equipped. . . .245 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 ▫ ParkSense® Display . . . . . . . . . . . . . . . . . . ..251 ▫ Enabling And Disabling ParkSense® . . . . . . ..254 ▫ Service The ParkSense® Rear Park Assist System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 ▫ Cleaning The ParkSense® System . . . . . . . . ..255 ▫ ParkSense® System Usage Precautions. . . . . ..256 䡵 PARKVIEW® REAR BACK UP CAMERA — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .258 ▫ Turning ParkView® On Or Off — With Navigation/Multimedia Radio . . . . . . . . . . ..260 䡵 PARKSENSE® REAR PARK ASSIST — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .249 ▫ ParkSense® Sensors . . . . . . . . . . . . . . . . . . ..250 ▫ ParkSense® Warning Display . . . . . . . . . . . ..250 ▫ Turning ParkView® On Or Off — Without Navigation/Multimedia Radio . . . . . . . . . . ..260 䡵 OVERHEAD CONSOLE . . . . . . . . . . . . . . . . ..261 ▫ Front Map/Reading Lights . . . . . . . . . . . . ..261 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Courtesy Lights . . . . . . . . . . . . . . . . . . . . . . .262 ▫ Sunglasses Bin Door . . . . . . . . . . . . . . . . . ..262 䡵 GARAGE DOOR OPENER — IF EQUIPPED . . .263 ▫ Before You Begin Programming HomeLink® . .264 ▫ Programming A Rolling Code . . . . . . . . . . . ..265 ▫ Programming A Non-Rolling Code . . . . . . . ..267 ▫ Canadian/Gate Operator Programming . . . . ..268 ▫ Using HomeLink®. . . . . . . . . . . . . . . . . . . ..270 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . .270 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . ..270 ▫ General Information. . . . . . . . . . . . . . . . . . ..271 䡵 POWER SUNROOF — IF EQUIPPED . . . . . . ..272 ▫ Opening Sunroof — Express . . . . . . . . . . . . ..273 ▫ Opening Sunroof — Manual Mode . . . . . . . ..273 ▫ Closing Sunroof — Express. . . . . . . . . . . . . ..273 ▫ Closing Sunroof — Manual Mode . . . . . . . . ..273 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . ..273 ▫ Venting Sunroof — Express . . . . . . . . . . . . ..274 ▫ Sunshade Operation. . . . . . . . . . . . . . . . . . ..274 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .274 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . ..274 ▫ Ignition OFF Operation . . . . . . . . . . . . . . . ..275 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . ..275 䡵 ELECTRICAL POWER OUTLETS . . . . . . . . . ..275 䡵 POWER INVERTER — IF EQUIPPED . . . . . . ..280 䡵 CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . . .282 ▫ Front Seat Cupholders . . . . . . . . . . . . . . . . ..282 ▫ Rear Cupholders . . . . . . . . . . . . . . . . . . . ..283 䡵 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .285 ▫ Glove Compartment . . . . . . . . . . . . . . . . . ..285 ▫ Door Storage. . . . . . . . . . . . . . . . . . . . . . . . .285 ▫ Front Center Console . . . . . . . . . . . . . . . . . ..286 ▫ Rear Full Center Console (If Equipped) . . . . ..287 ▫ Rear Mini Center Console (If Equipped) . . . ..291 䡵 CARGO AREA FEATURES . . . . . . . . . . . . . . ..292 ▫ Rechargeable Flashlight . . . . . . . . . . . . . . . ..292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 ▫ Cargo Storage . . . . . . . . . . . . . . . . . . . . . . .293 ▫ Retractable Cargo Area Cover — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .293 ▫ Cargo Tie-Down Hooks . . . . . . . . . . . . . . . ..294 䡵 REAR WINDOW FEATURES . . . . . . . . . . . . ..295 ▫ Rear Window Wiper/Washer . . . . . . . . . . . ..295 ▫ Rear Window Defroster . . . . . . . . . . . . . . . ..296 䡵 ROOF LUGGAGE RACK — IF EQUIPPED . . . .297 ▫ Deploying the Crossbars. . . . . . . . . . . . . . . ..298 ▫ Stowing the Crossbars . . . . . . . . . . . . . . . . ..301 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while the small control under the mirror is set in the day position (toward the windshield). Adjusting Rearview Mirror Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mir- ror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex passenger side mirror. Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will illuminate to indicate when the dim- ming feature is activated. The mirror is twisted on the windshield button counterclockwise and requires no tools for mounting. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 NOTE: This feature is disabled when the vehicle is moving in reverse. Automatic Dimming Mirror 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions: • full forward • full rearward and • normal. Outside Automatic Dimming Mirrors — If Equipped The drivers outside mirror will automatically adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror and can be turned on or off by pressing the button at the base of the inside mirror. The mirrors will automatically adjust for headlight glare when the inside mirror adjusts. Power Mirrors The power mirror switch is located on the driver’s side door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in “Understanding The Features Of Your Vehicle” for further information. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster if equipped. Some vehicles may not be equipped with rear window defroster, in this case the heated mirrors will still function as intended. Refer to “Rear Window Features” in “Understanding The Fea- tures Of Your Vehicle” for further information. Tilt Mirrors In Reverse (Available With Memory Seat Only) — If Equipped Tilt Mirrors in Reverse provides automatic outside mirror positioning which will aid the drivers view of the ground rearward of the front doors. Outside mirrors will move Power Mirror Switch 1 — Mirror Direction Control 2 — Mirror Selection 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE slightly downward from the present position when the vehicle is shifted into REVERSE. Outside mirrors will then return to the original position when the vehicle is shifted out of REVERSE position. Each stored memory setting will have an associated Tilt Mirrors in Reverse position. NOTE: The Tilt Mirrors in Reverse feature is not enabled when delivered from the factory. The Tilt Mirrors in Reverse feature can be enabled or disabled in the Elec- tronic Vehicle Information Center (EVIC). Refer to “Elec- tronic Vehicle Information Center (EVIC)/Customer- Programmable Features” in “Understanding Your Instru- ment Panel” for further information. Illuminated Vanity Mirrors To access an illuminated vanity mirror, flip down one of the visors. Lift the cover to reveal the mirror. The light will turn on automatically. Illuminated Vanity Mirror Sun Visor Extension — If Equipped This feature has a pull out extension on the sun visor for increased coverage. BLIND SPOT MONITORING — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle. Rear Detection Zones UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 When the vehicle is started, the BSM warning light will be momentarily illuminated in both outside rear view mirrors to let the driver know that the system is opera- tional. The BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand by mode when the vehicle is in PARK. The BSM detection zone covers approximately one lane on both sides of the vehicle (11 ft or 3.35 m). The zone starts at the outside rear view mirror and extends ap- proximately 20 ft (6 m) to the rear of the vehicle. The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed has reached approxi- mately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the de- tection zones. 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM warning light remaining illuminated the entire time the vehicle is in a forward gear. The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the BSM system can function properly. Do not block the area of the rear fascia where the radar sensors are located with foreign objects (bum- per stickers, bicycle racks, etc.). Sensor Location (Driver Side Shown) The BSM system notifies the driver of objects in the detection zones by illuminating the BSM warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “Modes Of Operation” for further information. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle. BSM Warning Light The BSM system monitors the detection zone from three different entry points (Side, Rear, Front) while driving to see if an alert is necessary. The BSM system will issue an alert during these types of zone entries. Side Monitoring 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Rear Vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h), the warning light will not illuminate. Rear Monitoring Overtaking/Approaching UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. Overtaking/Passing Stationary Objects 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicles mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death. Rear Cross Path The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed. The RCP system will then have a clear view of the cross traffic and if an oncoming vehicle is detected, alert the driver. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume. WARNING! RCP is not a Back Up Aid system. It is intended to be used to help a driver detect an oncoming vehicle in a parking lot situation. Drivers must be careful when backing up, even when using RCP. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before back- ing up. Failure to do so can result in serious injury or death. RCP Detection Zones RCP monitors the rear detection zones on both sides of the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately 1 to 2 mph (1 km/h to 3 km/h), to objects moving a maxi- mum of approximately 10 mph (16 km/h), such as in parking lot situations. 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Modes Of Operation Three selectable modes of operation are available in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Under- standing Your Instrument Panel” for further information. Blind Spot Alert When operating in Blind Spot Alert mode, the BSM system will provide a visual alert in the appropriate side view mirror based on a detected object. However, when the system is operating in RCP, the system will respond with both visual and audible alerts when a detected object is present. Whenever an audible alert is requested, the radio is muted. Blind Spot Alert Lights/Chime When operating in Blind Spot Alert Lights/Chime mode, the BSM system will provide a visual alert in the appro- priate side view mirror based on a detected object. If the turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and de- tected object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the audible alert the radio (if on) will also be muted. NOTE: • Whenever an audible alert is requested by the BSM • If the hazard flashers are on, the system will request system, the radio is also muted. the appropriate visual alert only. When the system is in RCP, the system shall respond with both visual and audible alerts when a detected object is present. Whenever an audible alert is requested, the radio is also muted. Turn/hazard signal status is ignored; the RCP state always requests the chime. Blind Spot Alert Off When the BSM system is turned off there will be no visual or audible alerts from either the BSM or RCP systems. NOTE: The BSM system will store the current operating mode when the vehicle is shut off. Each time the vehicle is started the previously stored mode will be recalled and used Astronomy Zone — System Temporarily Unavailable When the vehicle enters this zone the blind spot system will become temporarily unavailable and the EVIC will display the message “ Blind spot system unavailable- Astronomy zone”. The side mirrors LED’s will be lit up and stay lit until the vehicle exits the zone. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Uconnect® Phone — IF EQUIPPED Uconnect® Phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect® Phone al- lows you to dial a phone number with your mobile phone using simple voice commands (e.g., “Call” ѧ “Mike” ѧ “Work” or “Dial” ѧ “248-555-1212”). Your mobile phone’s audio is transmitted through your vehi- cle’s audio system; the system will automatically mute your radio when using the Uconnect® Phone. NOTE: The Uconnect® Phone requires a mobile phone equipped with the Bluetooth® “Hands-Free Profile”, Version 0.96 or higher. See the Uconnect® website for supported phones. For Uconnect® Customer Support: U.S. residents - visit www.UconnectPhone.com or call 1–877–855–8400. Cana- dian Residents - visit www.DriveUconnect.ca or call, 1-800-465–2001 (English) or 1-800-387-9983 (French). 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect® Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The Uconnect® Phone is driven through your Bluetooth® “Hands-Free Profile” mobile phone. Uconnect® features Bluetooth® technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so Uconnect® Phone works no matter where you stow your mobile phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s Uconnect® Phone. The Uconnect® Phone allows up to seven mobile phones to be linked to the system. Only one linked (or paired) mobile phone can be used with the system at a time. The system is available in English, Spanish, or French languages. WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. Uconnect® Phone Button radio or controls steering wheel The (if equipped) will contain the two control buttons button and Voice Com- (Uconnect® Phone mand button) that will enable you to access the system. When you press the button you will hear the word Uconnect® followed by a BEEP. The beep is your signal to give a command. Voice Command Button Actual button location may vary with the ra- dio. The individual buttons are described in the “Operation” section. The Uconnect® Phone can be used with any Hands-Free Profile certified Bluetooth® mobile phone. See the Uconnect® website for supported phones. Refer to your mobile service provider or the phone manufacturer for details. The Uconnect® Phone is fully integrated with the vehi- cle’s audio system. The volume of the Uconnect® Phone can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the Uconnect® Phone such as “CELL” or caller ID on certain radios. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Operation Voice commands can be used to operate the Uconnect® Phone and to navigate through the Uconnect® Phone menu structure. Voice commands are required after most Uconnect® Phone prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the beep, which follows the “Ready” prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying “Setup” and then “Pair a Device”, the following compound command can be said: “Pair a Bluetooth® Device”. 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For each feature explanation in this section, only the compound form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the compound form voice com- mand “Phonebook New Entry”, or you can break the compound form command into two voice commands: “Phonebook” and “New Entry”. Please remember, the Uconnect® Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you. Voice Command Tree Refer to “Voice Tree” in this section. Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say “Help” following the beep. The Uconnect® Phone will play some of the options at any prompt if you ask for help. To activate the Uconnect® Phone, simply press the button and follow the audible prompts for directions. Uconnect® Phone sessions begin with a press of the button on the radio control head. Cancel Command At any prompt, after the beep, you can say “Cancel” and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) Uconnect® Phone To A Mobile Phone To begin using your Uconnect® Phone, you must pair your compatible Bluetooth® enabled mobile phone. To complete the pairing process, you will need to refer- ence your mobile phone Owner’s Manual. The Uconnect® website may also provide detailed instruc- tions for pairing. button to begin. “Device Pairing”. and follow the audible prompts. The following are general phone to Uconnect® Phone pairing instructions: • Press the • After the “Ready” prompt and the following beep, say • When prompted, after the beep, say “Pair a Device” • You will be asked to say a four-digit Personal Identi- fication Number (PIN), which you will later need to enter into your mobile phone. You can enter any four-digit PIN. You will not need to remember this PIN after the initial pairing process. • For identification purposes, you will be prompted to give the Uconnect® Phone a name for your mobile phone. Each mobile phone that is paired should be given a unique phone name. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 • You will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones to your Uconnect® Phone. However, at any given time, only one mobile phone can be in use, connected to your Uconnect® System. The priority allows the Uconnect® Phone to know which mobile phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the Uconnect® Phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at any time (refer to “Advanced Phone Connectivity” in this section). Dial By Saying A Number • Press the • After the “Ready” prompt and the following beep, say button to begin. “Dial”. want to call. 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the number you • For example, you can say “234-567-8901”. • The Uconnect® Phone will confirm the phone number and then dial. The number will appear in the display of certain radios. “Call”. button to begin. Call By Saying A Name • Press the • After the “Ready” prompt and the following beep, say • The system will prompt you to say the name of the • After the “Ready” prompt and the following beep, say the name of the person you want to call. For example, you can say “John Doe”, where John Doe is a previ- ously stored name entry in the Uconnect® phonebook person you want to call. or downloaded phonebook. To learn how to store a name in the phonebook, refer to “Add Names to Your Uconnect® Phonebook”, in the phonebook. • The Uconnect® system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Phonebook Download – Automatic Phonebook Transfer From Mobile Phone If equipped and specifically supported by your phone, Uconnect® Phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific Bluetooth® Phones with Phone Book Access Profile may support this feature. See Uconnect® website for supported phones. • To call a name from the Uconnect® Phonebook or downloaded Phonebook, follow the procedure in “Call by Saying a Name” section. • Automatic download and update, if supported, begins as soon as the Bluetooth® wireless phone connection is made to the Uconnect® Phone, for example, after you start the vehicle. • A maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the Uconnect® Phone. • Depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previously downloaded phonebook is avail- able for use. • Only the phonebook of the currently connected mobile • Either the mobile phone’s phonebook or the mobile phone is accessible. phone’s SIM card phonebook is downloaded. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 • This downloaded phonebook cannot be edited or deleted on the Uconnect® Phone. These can only be edited on the mobile phone. The changes are trans- ferred and updated to Uconnect® Phone on the next phone connection. button to begin. Add Names To Your Uconnect® Phonebook NOTE: Adding names to the Uconnect® Phonebook is recommended when the vehicle is not in motion. • Press the • After the “Ready” prompt and the following beep, say • When prompted, say the name of the new entry. Use of long names helps the Voice Command and it is recom- mended. For example, say “Robert Smith” or “Robert” instead of “Bob”. “Phonebook New Entry”. 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., “Home”, “Work”, “Mobile”, or “Other”). This will allow you to store multiple numbers for each phone- book entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The Uconnect® Phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, Uconnect® Phone automati- cally downloads your mobile phone’s phonebook. Edit Uconnect® Phonebook Entries button to begin. deleted or edited. when the vehicle is not in motion. NOTE: • Editing names in the phonebook is recommended • Automatic downloaded phonebook entries cannot be • Press the • After the “Ready” prompt and the following beep, say • You will then be asked for the name of the phonebook • Next, choose the number designation (home, work, • When prompted, recite the new phone number for the mobile, or other) that you wish to edit. entry that you wish to edit. “Phonebook Edit Entry”. phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “Phonebook Edit Entry” can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add “John Doe’s” work number later using the “Phonebook Edit Entry” feature. Delete Uconnect® Phonebook Entry NOTE: Editing phonebook entries is recommended when the vehicle is not in motion. • Press the • After the “Ready” prompt and the following beep, say button to begin. “Phonebook Delete”. the UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “List Names” to hear a list of the entries in the phonebook from which you choose. To select one of the entries from the list, press button while the Uconnect® Phone is playing the desired entry and say “Delete”. • After you enter the name, the Uconnect® Phone will ask you which designation you wish to delete: home, work, mobile, other, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current • Automatic downloaded phonebook entries cannot be language is deleted. deleted or edited. button to begin. “Phonebook Erase All”. 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete/Erase “All” Uconnect® Phonebook Entries • Press the • After the “Ready” prompt and the following beep, say • The Uconnect® Phone will ask you to verify that you • After confirmation, the phonebook entries will be • Note that only the phonebook in the current language • Automatic downloaded phonebook entries cannot be wish to delete all the entries from the phonebook. is deleted. deleted. deleted or edited. List All Names In The Uconnect® Phonebook • Press the • After the “Ready” prompt and the following beep, say button to begin. “Phonebook List Names”. • The Uconnect® Phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available. • To call one of the names in the list, press the button during the playing of the desired name, and say “Call”. NOTE: The user can also exercise “Edit” or “Delete” operations at this point. • The Uconnect® Phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the Uconnect® Phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the Uconnect® Phone. Check with your mobile service provider for the features that you have. Answer Or Reject An Incoming Call — No Call Currently In Progress When you receive a call on your mobile phone, the Uconnect® Phone will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the button to accept the call. To reject the call. Press the button until you hear a single call, press and hold the beep, indicating that the incoming call was rejected. Answer Or Reject An Incoming Call — Call Currently In Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your button to place the current mobile phone. Press the call on hold and answer the incoming call. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: The Uconnect® Phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making A Second Call While Current Call Is In Progress To make a second call while you are currently on a call, button and say “Dial” or “Call” followed press the by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to “Toggling Between Calls” in this section. To combine two calls, refer to “Conference Call” in this section. 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place/Retrieve A Call From Hold To put a call on hold, press the button until you hear a single beep. This indicates that the call is on hold. To but- bring the call back from hold, press and hold the ton until you hear a single beep. Toggling Between Calls If two calls are in progress (one active and one on hold), press the button until you hear a single beep, indicat- ing that the active and hold status of the two calls have switched. Only one call can be placed on hold at a time. Conference Call When two calls are in progress (one active and one on button until you hear a hold), press and hold the double beep indicating that the two calls have been joined into one conference call. Three-Way Calling To initiate three-way calling, press the button while a call is in progress, and make a second phone call, as described under “Making a Second Call While Current Call is in Progress”. After the second call has established, button until you hear a double press and hold the beep, indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, momentarily press the but- ton. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the button until you hear a single beep. button to begin. Redial • Press the • After the “Ready” prompt and the following beep, say • The Uconnect® Phone will call the last number that “Redial”. was dialed from your mobile phone. NOTE: This may not be the last number dialed from the Uconnect® Phone. Call Continuation Call continuation is the progression of a phone call on the Uconnect® Phone after the vehicle ignition key has been switched to OFF. Call continuation functionality avail- able on the vehicle can be any one of three types: • After the ignition key is switched to OFF, a call can continue on the Uconnect® Phone either until the call UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 ends, or until the vehicle battery condition dictates cessation of the call on the Uconnect® Phone and transfer of the call to the mobile phone. • After the ignition key is cycled to OFF, a call can continue on the Uconnect® Phone for a certain dura- tion, after which the call is automatically transferred from the Uconnect® Phone to the mobile phone. • An active call is automatically transferred to the mo- bile phone after the ignition key is cycled to OFF. Uconnect® Phone Features Language Selection To change the language that the Uconnect® Phone is using: • Press the • After the “Ready” prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. button to begin. 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every Uconnect® Phone language change operation, only the language-specific 32-name phone- book is usable. The paired phone name is not language- specific and is usable across all languages. Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the Uconnect® Phone is operational, you may reach the emergency number as follows: • Press the • After the “Ready” prompt and the following beep, say “Emergency” and the Uconnect® Phone will instruct the paired mobile phone to call the emergency number. This feature is supported in the U.S., Canada, and Mexico. button to begin. NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available mobile service and area. • If supported, this number may be programmable on some button and say systems. To do this, press the “Setup”, followed by “Emergency”. • The Uconnect® Phone does slightly lower your chances of successfully making a phone call as to that for the mobile phone directly. WARNING! To use you Uconnect® Phone System in an emergency, your mobile phone must be: • turned on, • paired to the Uconnect® System, • and have network coverage. Roadside Assistance If you need roadside assistance: • Press the button to begin. • After the “Ready” prompt and the following beep, say “Roadside Assistance”. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 NOTE: • The roadside assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- 3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). Please refer to the “Roadside Assistance” coverage details on the DVD in the War- ranty Information Booklet and the Roadside Assis- tance references. • If supported, this number may be programmable on button and say some systems. To do this, press the “Setup”, followed by “Roadside Assistance”. Paging To learn how to page, refer to “Working with Automated Systems”. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the Uconnect® Phone. 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Mail Calling To learn how to access your voice mail, refer to “Working with Automated Systems”. Working With Automated Systems This method is used in instances where one generally has to press numbers on the mobile phone keypad while navigating through an automated telephone system. You can use your Uconnect® Phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some services re- quire immediate response selection. In some instances, that may be too quick for use of the Uconnect® Phone. When calling a number with your Uconnect® Phone that normally requires you to enter in a touch-tone sequence on your mobile phone keypad, you can press the button and say the sequence you wish to enter, followed by the word “Send”. For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you button and say, “3 7 4 6 #Send”. can press the Saying a number, or sequence of numbers, followed by “Send”, is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored Uconnect® phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to button and say, “Send.” The call and then press the system will prompt you to enter the name or number and say the name of the phonebook entry you wish to send. The Uconnect® Phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. network configurations. This is normal. NOTE: • You may not hear all of the tones due to mobile phone • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge In — Overriding Prompts The “Voice Command” button can be used when you wish to skip part of a prompt and issue your voice command immediately. For example, if a prompt is asking “Would you like to pair a phone, clear a...,” you button and say, “Pair a Phone” to could press the select that option without having to listen to the rest of the voice prompt. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Turning Confirmation Prompts ON/OFF Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect® Phone will not repeat a phone number before you dial it). • Press the • After the “Ready” prompt and the following beep, say button to begin. one of the following: – “Setup Confirmation Prompts On” – “Setup Confirmation Prompts Off” Phone And Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your mobile phone, the Uconnect® Phone will provide notifica- tion to inform you of your phone and network status when you are attempting to make a phone call using Uconnect® Phone. The status is given for network signal strength, phone battery strength, etc. 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using The Mobile Phone Keypad You can dial a phone number with your mobile phone keypad and still use the Uconnect® Phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth® mobile phone, the audio will be played through your vehicle’s audio system. The Uconnect® Phone will work the same as if you dial the number using Voice Command. NOTE: Certain brands of mobile phones do not send the dial ring to the Uconnect® Phone to play it on the vehicle audio system, so you will not hear it. Under this situa- tion, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio. Mute/Un-Mute (Mute ON/OFF) When you mute the Uconnect® Phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the Uconnect® Phone: • Press the • Following the beep, say “Mute”. In order to un-mute the Uconnect® Phone: • Press the • Following the beep, say “Mute off”. Advanced Phone Connectivity button. button. Transfer Call To And From Mobile Phone The Uconnect® Phone allows ongoing calls to be trans- ferred from your mobile phone to the Uconnect® Phone without terminating the call. To transfer an ongoing call from your Uconnect® Phone paired mobile phone to the button Uconnect® Phone or vice versa, press the and say “Transfer Call”. Connect Or Disconnect Link Between The Uconnect® Phone And Mobile Phone Your mobile phone can be paired with many different electronic devices, but can only be actively “connected” with one electronic device at a time. If you would like to connect or disconnect the Bluetooth® connection between your mobile phone and the Uconnect® Phone System, follow the instructions described in your mobile phone User’s Manual. List Paired Mobile Phone Names • Press the • After the “Ready” prompt and the following beep, say button to begin. “Setup Phone Pairing”. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 • When prompted, say “List Phones”. • The Uconnect® Phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “Select” or “Delete” a paired phone being announced, press the button and say “Se- lect” or “Delete”. Also, see the next two sections for an alternate way to “Select” or “Delete” a paired phone. button to begin. Select Another Mobile Phone This feature allows you to select and start using another phone paired with the Uconnect® Phone. • Press the • After the “Ready” prompt and the following beep, say • You can also press the button at any time while the list is being played, and then choose the phone that you wish to select. “Setup Select Phone” and follow the prompts. 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. the Uconnect® Phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. the selected phone is not available, If button to begin. “Setup Phone Pairing”. Delete Uconnect® Phone Paired Mobile Phones • Press the • After the “Ready” prompt and the following beep, say • At the next prompt, say “Delete” and follow the • You can also press the button at any time while the list is being played, and then choose the phone you wish to delete. prompts. Things You Should Know About Your Uconnect® Phone Uconnect® Phone Tutorial To hear a brief tutorial of the system features, press the button and say “Uconnect® Tutorial.” Voice Training For users experiencing difficulty with the system recogniz- ing their voice commands or numbers, the Uconnect® Phone Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the Uconnect® Phone mode (e.g., from radio mode): • Press and hold the • Press the button and say the “Voice Training”, “System Training”, or “Start Voice Training” com- mand. button for five seconds until the session begins, or, You can either press the Uconnect® Phone button to restore the factory setting or repeat the words and phrases when prompted by the Uconnect® Phone. For best results, the Voice Training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. Reset • Press the • After the “Ready” prompt, and the following beep, say button. “Setup”, then “Reset”. This will delete all phone pairing, phone book entries, and other settings in all language modes. The System will prompt you before resetting to factory settings. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Voice Command • For best performance, adjust the rearview mirror to provide at least ½ in (1 cm) gap between the overhead console (if equipped) and the mirror. • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a Voice Command period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say “Send”. • Storing names in the phonebook when the vehicle is • It is not recommended to store similar sounding names not in motion is recommended. in the Uconnect® Phonebook. be spoken “eight-zero-zero” not “eight hundred”. • Phonebook (Downloaded and Uconnect® Phone Lo- cal) name recognition rate is optimized when the entries are not similar. • Numbers must be spoken in single digits. “800” must • You can say “O” (letter “O”) for “0” (zero). • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • In a convertible vehicle, system performance may be compromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the Uconnect® Phone. • Echo at the phone far end can sometimes be reduced • In a convertible vehicle, system performance may be by lowering the in-vehicle audio volume. compromised with the convertible top down. Recent Calls If your phone supports “Automatic Phonebook Down- load”, Uconnect® Phone can list your Outgoing, Incom- ing and Missed Calls. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 SMS Uconnect® Phone can read or send new messages on your phone. Read Messages: If you receive a new text message while your phone is connected to Uconnect® Phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • Press the • After the “Ready” prompt and the following beep, say • Uconnect® Phone will play the new text message for “SMS Read” or “Read Messages.” button. you. After reading a message, you can “Reply” or “Forward” the message using Uconnect® Phone. 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Send Messages: You can send messages using Uconnect® Phone. To send a new message: • Press the • After the “Ready” prompt and the following beep, say • You can either say the message you wish to send or say “SMS Send” or “Send Message.” button. “List Messages.” There are 20 preset messages. button while the To send a message, press the system is listing the message and say “Send.” Uconnect® Phone will prompt you to say the name or number of the person you wish to send the message to. List of Preset Messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L O L 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See You in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18. When can we meet? 19. Send number to call 20. Start without me Turn SMS Incoming Announcement ON/OFF Turning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming mes- sages. • Press the • After the “Ready” prompt and the following beep, say “Setup, SMS Incoming Message Announcement,” you will then be given a choice to change it. button. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Bluetooth® Communication Link Mobile phones have been found to lose connection to the Uconnect® Phone. When this happens, the connection can generally be reestablished by switching the phone off/on. Your mobile phone is recommended to remain in Bluetooth® ON mode. Power-Up After switching the ignition key from OFF to either the ON or ACC position, or after a language change, you must wait at least fifteen seconds prior to using the system. 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Voice Commands Alternate (s) Primary all call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Alternate (s) Voice Commands Alternate (s) Primary previous record again redial return to main menu return or main menu Primary help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing phonebook pairing phone book select phone settings or phone set up select phone send set up towing assistance transfer call Uconnect® Tutorial voice training work yes General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 VOICE COMMAND — IF EQUIPPED Voice Command System Operation The Uconnect® Voice Command system allows you to control your AM, FM radio, disc player, USB Mass Storage Class device, iPod family of devices, Bluetooth Streaming Audio device, and a memo recorder. NOTE: Take care to speak into the Voice Interface Sys- tem as calmly and normally as possible. The ability of the Voice Interface System to recognize user voice commands may be negatively affected by rapid speaking or a raised voice level. 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. button, you When you press the Voice Command will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists button, listen for options, press the Voice Command the beep, and say your command. Pressing the Voice Command button while the system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands. This will become helpful once you start to learn the options. NOTE: At any time, you can say the words “Cancel”, “Help” or “Main Menu”. These commands are universal and can be used from any menu. All other commands can be used depending upon the active application. When using this system, you should speak clearly and at a normal speaking volume. The system will best recognize your speech if the win- dows are closed, and the heater/air conditioning fan is set to low. At any point, if the system does not recognize one of your commands, you will be prompted to repeat it. button and say “Help” or “Main Menu”. To hear the first available Menu, press the Voice Com- mand Commands The Voice Command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing The Volume 1. Start a dialogue by pressing the Voice Command button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Com- mand system is speaking. Please note the volume setting for Voice Command is different than the audio system. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Main Menu Start a dialogue by pressing the Voice Command button. You may say “Main Menu” to switch to the main menu. In this mode, you can say the following commands: • “Radio AM” (to switch to the radio AM mode) • “Radio FM” (to switch to radio FM mode) • “Disc” (to switch to the disc mode) • “USB” (to switch to USB mode) • “Bluetooth Streaming” (to switch to Bluetooth® Stream- • “Memo” (to switch to the memo recorder) • “System Setup” (to switch to system setup) ing mode) 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio AM To switch to the AM band, say “AM” or “Radio AM”. In this mode, you may say the following commands: • “Frequency #” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Radio FM To switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency #” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Menu Radio” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Satellite Radio To switch to satellite radio mode, say “Sat” or “Satellite Radio”. In this mode, you may say the following com- mands: • “Channel Number” (to change the channel by its • “Next Channel” (to select the next channel) • “Previous Channel” (to select the previous channel) • “List Channel” (to hear a list of available channels) • “Select Name” (to say the name of a channel) • “Menu Radio” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) spoken number) Disc Mode To switch to the disc mode, say “Disc”. In this mode, you may say the following commands: • “Track” (#) (to change the track) • “Next Track” (to play the next track) • “Previous Track” (to play the previous track) • “Main Menu” (to switch to the main menu) USB Mode To switch to USB mode, say “USB”. In this mode, you may say the following commands: • “Next Track” (to play the next track) • “Previous Track” (to play the previous track) • “Play” (to play a Artist Name, Playlist Name, Album Name, Track Name, etc.) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Bluetooth® Streaming (BT) Mode To switch to Bluetooth® Streaming (BT) mode, say “Bluetooth Streaming”. In this mode, you may say the following commands: • “Next Track” (to play the next track) • “Previous Track” (to play the previous track) • “List” (to list an Artist, Playlist, Album, Track, etc.) Memo Mode To switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the the Voice Command button to stop recording. You proceed by saying recording, you may press one of the following commands: – “Save” (to save the memo) – “Continue” (to continue recording) 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE – “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) — During the playback you may press the Voice Com- button to stop playing memos. You pro- mand ceed by saying one of the following commands: – “Repeat” (to repeat a memo) – “Next” (to play the next memo) – “Previous” (to play the previous memo) – “Delete” (to delete a memo) • “Delete All” (to delete all memos) Setup To switch to system setup, you may say on of the following: • “Change to system setup” • “Main menu system setup” • “Switch to system setup” • “Change to setup” • “Main menu setup” or • “Switch to setup” In this mode, you may say the following commands: • “Language English” • “Language French” • “Language Spanish” • “Tutorial” • “Voice Training” NOTE: Keep in mind that you have to press the Voice button first and wait for the beep before Command speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers the Uconnect® Voice “Voice Training” feature may be used. 1. Press the Voice Command button, say “System Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2. Repeat the words and phrases when prompted by Uconnect® Voice. For best results, the Voice Training session should be completed when the vehicle is parked, engine running, all windows closed, and the blower fan switched off. This procedure may be re- peated with a new user. The system will adapt to the last trained voice only. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 SEATS Seats are part of the Occupant Restraint System of the vehicle. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats — If Equipped Some models may be equipped with eight-way power driver and front passenger seats. The power seat switches are located on the outboard side of the seat. There are two switches that control the movement of the seat cushion and the seatback. Power Seat Switches 1 — Seatback Switch 2 — Seat Switch Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted up or down. Pull upward or push downward on the front of the seat switch, the front of the seat cushion will move in the direction of the switch. Release the switch when the desired position has been reached. Reclining The Seatback The angle of the seatback can be adjusted forward or rearward. Push the seatback switch forward or rearward, UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 the seat will move in the direction of the switch. Release the switch when the desired position is reached. WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Passenger’s Power Seat — If Equipped Some models are equipped with a six-way power pas- senger seat. The power seat switch is located on the outboard side of the seat. The switch is used to control the movement of the seat and seat cushion. Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2013 Dodge Durango Owners Manual