2006 Dodge Durango Owners Manual

bottom of the fill hole. Selection of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owner in the proper selection of grease for chassis components. This symbol, an example shown below, is located on the grease container and identifies the appli- cation and quality of the grease.

366 MAINTAINING YOUR VEHICLE

are

There two groups identified, those for wheel bearings (Letter “G”) and those for chassis (Letter “L”) lubrication. Perfor- mance categories within these groups result in dual letter for each group. The letter des- ignations shown in the ex- ample the highest quality level available and when combined as shown can be used for chassis lubrication. Use only those greases that have the NLGI symbol on the container along with the proper quality level for your application.

designations

are

Appearance Care and Protection from Corrosion

Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.

The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- • Use Mopar威 auto polish to remove road film and stains and to polish your vehicle. Take care never to scratch the paint.

lated on your vehicle, wash it as soon as possible.

MAINTAINING YOUR VEHICLE 367

• Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.

CAUTION!

Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.

Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and liftgate be kept clear and open.

368 MAINTAINING YOUR VEHICLE

• If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibil- ity of the owner. • All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with mild soap and water to prevent corrosion. To remove heavy soil, select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only Mopar威 cleaners are recommended. Do not use oven cleaner. Avoid auto- matic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective fin- ish.

• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider • Use Mopar威 touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle.

mud or stone shields behind each wheel.

Interior Care Use Mopar威 Fabric Cleaner to clean fabric upholstery and carpeting. Use Mopar威 Vinyl Cleaner to clean vinyl upholstery and trim. Mopar威 Total Clean is specifically recommended for leather upholstery.

Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar威 Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition.

WARNING!

Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.

MAINTAINING YOUR VEHICLE 369

Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer. Do not use scrapers or other sharp instru- ments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic.

370 MAINTAINING YOUR VEHICLE

1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly.

POWER DISTRIBUTION CENTER (FUSE/RELAY) Your vehicle is equipped with two electrical power distribution centers located next to each other in the left side of the engine compartment. The power distribution centers house new plug-in “Maxi” fuses which replace all the in-line fusible links previously used. The power distribution centers also contain “Mini”fuses and plug-in “ISO” relays. A label inside the latching cover of the Power Distribution Cen- ters identifies each component for ease of replacement, if necessary. These fuses and relays can be obtained from your dealer.

FUSE BLOCK

CAUTION!

When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it suggests a problem in the circuit that must be corrected.

If you are leaving your vehicle dormant for NOTE: longer than 21 days you may want to take steps to protect your battery. You may do this by disconnecting the battery or by disconnecting the two ignition-off draw (I.O.D.) fuses located in the Auxiliary Power Distribution Center (PDC) located in the engine compartment. The I.O.D. cavities include a snap-in retainer that allows the

MAINTAINING YOUR VEHICLE 371

fuse to be disconnected, without removing it from the fuse block. Pressing the I.O.D. fuse back into the cavity reconnects it. Interior Fuses The fuse block contains blade-type mini-fuses, relays, and circuit breakers for high-current circuits. It is located in the left kick panel. It is accessible through a snap-in cover.

372 MAINTAINING YOUR VEHICLE

Cavity Mini Fuse/Color

Description

F1

F 2

F3

F4

F5

F6
F7

F8

F9
F10

Fuse Block

15 Amp Blue

10 Amp Red

10 Amp Red

Instrument Cluster Battery

Feed

Occupant Classification

Module (OCM) Battery Feed Ignition Run/Start for Con-

troller (NGC), Integrated Power Module (IPM), AC Relay and Fuel Pump Relay

10 Amp Red

(2) 10 Amp Red

Door Node and Non- Memory Power Mirror

Switch Battery Feed

Airbags (2 Fuses in Yellow

Holder)

10 Amp Red

Ignition Run/Start Unlock

25 Amp Natural

Radio Battery Feed

10 Amp Red

10 Amp Red 10 Amp Red

Ignition Run/Start for

Cluster/Transfer Case/Seat

Sw. Back lighting

SDAR/DVD Battery Feed

Spare

Cavity Mini Fuse/Color

10 Amp Red

20 Amp Yellow

10 Amp Red

10 Amp Red

15 Amp Blue

20 Amp Yellow

20 Amp Yellow

10 Amp Red

15 Amp Blue

Description

Heated Mirrors

Cluster Battery Feed Ignition Run HVAC

Module/Heated Rear Glass

(EBL) Relay

ABS Module Ignition Run Battery Feed Blue Tooth, Compass/Trip Computer (CMTC), Sentry Key Diag-

nostics

Reconfigurable Power Out-

lets

Cigar Lighter Ignition

Spare Fuse

Heating & Air Conditioning w/ATC Only Battery Feed

25 Amp Natural

Amplifier Battery Feed

F11
F12

F13

F14

F15

F16

F17
F18

F19

F20

MAINTAINING YOUR VEHICLE 373

Underhood Fuses (Power Distribution Center)

Cavity

10
11

Cartridge

Fuse / Relay 30 Amp Pink 30 Amp Pink 40 Amp Green 30 Amp Pink

40 Amp Green 20 Amp Blue

40 Amp Green

40 Amp Green

Spare 30 Amp Pink 40 Amp Green

Mini Fuse

Description

Starter Front Wiper Brake Batt JB Feed Acc # Power Seats JB Feed Ign # JB Feed Ign # JB Feed Acc Delay

ASD Power Liftgate ( If Equipped)

374 MAINTAINING YOUR VEHICLE

Cavity

12

13
14
15
16
17
18
19
20
21
22
23
24
25
26

Cartridge

Fuse / Relay 40 Amp Green

30 Amp Pink 40 Amp Green 50 Amp Red

Mini Fuse

Description

Cavity

Cartridge

Fuse / Relay

JB Feed / EBL / T Case Brake JB Feed RR ABS Pump JB Feed Crank

10 Amp Red Spare 20 Amp Yellow Fuel Pump 20 Amp Yellow NGC Spare 20 Amp Yellow ABS Batt 20 Amp Yellow NGC Batt 20 Amp Yellow Trailer Tow A/C Clutch 15 Amp Blue 15 Amp Blue JB Feed Stop Spare

27

28
29
30
31
32
33
34
35

36
37

38
39
40

Relay Relay Spare Relay Relay Relay Relay

Spare Spare

Spare Relay Relay

Mini Fuse

Description

10 Amp Red

JB Feed Acc #

Spare

Run Start Run Remote

Starter ETAX AC Clutch Fuel Pump Rly

Brake Supres- sion

Blower Motor ASD Rly

Underhood Fuses (Integrated Power Module)

Cartridge

Fuse / Relay Relay

Relay

Relay Relay

Relay

Relay

Relay

Cavity

10

Mini Fuse

Description

Wiper On/Off Rly Wiper Hi/Lo Rly Horn Rly Rear Wiper Rly Lt T-Tow Stop/Turn Rly Rt T-Tow Stop/Turn Rly Park Lamps Rly Lt Park Lamps T-Tow Park Lamps Rt Park Lamps

10 Amp Red 10 Amp Red

10 Amp Red

Cavity

11

12
13
14

15
16
17
18
19

20
21

22
23

Cartridge

Fuse / Relay Relay

30 Amp Pink 40 Amp Green

MAINTAINING YOUR VEHICLE 375

Mini Fuse

Description

Rad Fan Hi Rly

20 Amp Yellow FCM Batt #4
20 Amp Yellow FCM Batt #2
20 Amp Yellow Adjustable

Pedal

20 Amp Yellow Ft Fog Lamps 20 Amp Yellow Horn 20 Amp Yellow Rear Wiper 20 Amp Yellow FCM Batt #1
20 Amp Yellow Lt T-Tow

Stop/Turn

20 Amp Yellow FCM Batt #3
20 Amp Yellow Rt T-Tow Stop/Turn FCM BATT # 5
Rad Fan

376 MAINTAINING YOUR VEHICLE

Cartridge

Fuse / Relay Relay

Relay

Relay

Cavity

24

25

26

27
28
29
30

Mini Fuse

Description

REPLACEMENT LIGHT BULBS

Rad Fan Lo Rly Ft Fog Lamps Rly Adjustable Pedal Rly

30 Amp Green IOD #1
30 Amp Green IOD #2

Spare Spare

LIGHT BULBS — Interior Bulb No. Dome Light . . . . . . . . . . . . . . . . . . . . . . . . WL212–2
Liftgate Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 567
Overhead Console Lights . . . . . . . . . . . . . PLW214–2A Reading Light . . . . . . . . . . . . . . . . . . . . . . . WL212–2
Visor Vanity Lights . . . . . . . . . . . . . . . Not Serviceable

LIGHT BULBS — Outside Bulb No. Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H13
Front Park/Turn/Sidemarker . . . . . . . . . . . . . 3457AK Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3057
Center High Mounted Stoplight . . . . . . . . . . . . . . 921
Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 9006LL Rear Sidemarker . . . . . . . . . . . . . . . . . . . . . . . . . 168
License Plate Light . . . . . . . . . . . . . . . . . . . . . . . 168
Rear Tail, Stop, Turn Signal. . . . . . . . . . . . . . . . . 3057

BULB REPLACEMENT

Headlights/Parking/Turn Signal

1. Remove the two bolts attaching the headlight to the inner fender panel.

MAINTAINING YOUR VEHICLE 377

2. Remove one nut that attaches the headlight to the inner fender panel. Access to the nut is possible by removing the fender panel access door which is located in the wheel liner. 3. Grasp the headlight and pull firmly to disengage the headlight from the fender panel. 4. While firmly holding the headlight in your hands disconnect all connectors by following the procedure described in step number 5 below. 5. Remove the bulb connector from the headlight making sure to pull and release the red tab on all connectors. Loosen the connector by pressing down on the black and/or green release which is located below or above the red tab. The green release is located above the red tab on the H13, the black release is located above the 3457AK red tab.

378 MAINTAINING YOUR VEHICLE

6. Twist and remove socket from lamp. 7. Remove bulb from socket and replace. NOTE: These are Halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat build-up which reduces bulb life. Rear Side Marker, Tail Lights, Turn Signals And Backup Lights — Replacement

1. Remove the two push-pins from the tail light housing.

MAINTAINING YOUR VEHICLE 379

2. Rotate the light to the outboard side of the vehicle and remove.

380 MAINTAINING YOUR VEHICLE

3. Unlock and remove electrical connector.

4. Remove the three screws holding the bulb strip to the back of the tail lamp.

5. Remove the bulb strip from the tail light lens.

MAINTAINING YOUR VEHICLE 381

6. Remove bulbs from bulb strip by pulling the bulb straight out.

382 MAINTAINING YOUR VEHICLE

License Lights

1. Remove the two screws securing the lens to the liftgate.

2. Rotate the socket 1/4 turn counterclockwise.

Center High-Mounted Stoplight

MAINTAINING YOUR VEHICLE 383

1. Remove two screws securing stoplight housing assem- bly to the liftgate.

3. Pull bulb from socket.

384 MAINTAINING YOUR VEHICLE

2. Turn socket 1/4 counterclockwise and free from hous- ing.

Fog Lights

1. Rotate bulb and connector 1/4 turn counterclockwise. 2. Pull bulb off of connector. NOTE: For foglights ensure that the takeout push- fasteners are relocated back in their positions; one in the foglight molding and the other in the hydroform.

3. Pull bulb straight from socket to remove.

FLUIDS AND CAPACITIES

Fuel

Engine Oil (with filter)

3.7L/4.7L, 87 Octane

5.7L, 89 Octane

3.7L, SAE 5W-30, API Certified 4.7L, SAE 5W-30, API Certified 5.7L, SAE 5W-20, API Certified

Cooling System (includes 2.1 Qts./2L for coolant bottle 3.7L without Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula)

3.7L with Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula)

4.7L without Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula)

4.7L with Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula)

5.7L without Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula)

5.7L with Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula)

NOTE: All fluid capacities are approximate.

MAINTAINING YOUR VEHICLE 385

U.S.

Metric

27 Gal. 27 Gal

5 Qt. 6 Qt. 7 Qt.

13.5 Qt. 14.5 Qt. 13.1 Qt. 14.2 Qt.

NA

16.6 Qt.

102L 102L

4.7L 5.7L 6.6L

12.9L 13.8L 12.5L 13.5L NA 15.8L

386 MAINTAINING YOUR VEHICLE

FLUIDS, LUBRICANTS AND GENUINE PARTS

Engine Component Engine Coolant

3.7/4.7L Engine Oil

5.7L Engine Oil

Engine Oil Filter Spark Plugs

Fuel Selection 3.7L/4.7L Fuel Selection 5.7L

Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent. Use SAE 5W-30, API Certified, meeting material standard MS-6395 or equiva- lent. Use SAE 5W-20, API Certified, meeting material standard MS-6395 or equiva- lent. Mopar威 Engine Oil Filter, P/N 5281090 or equivalent. Refer to the Vehicle Emission Control Information label in the engine com- partment. 87 Octane, (R+M)/2 Method 89 Octane, (R+M)/2 Method

MAINTAINING YOUR VEHICLE 387

Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder

Power Steering Reservoir

Fluids, Lubricants and Genuine Parts. Mopar威 ATF+4, Automatic Transmission Fluid. Mopar威 ATF+4, Automatic Transmission Fluid. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant or equivalent. SAE 75W-140 Synthetic Gear Lubricant or equivalent. Mopar威 DOT 3 and SAE J1703 should be used or equivalent. If DOT 3
brake fluid is not available, then DOT 4 is acceptable. Use only recom- mended brake fluids. Mopar威 ATF+4, Automatic Transmission Fluid.

MAINTENANCE SCHEDULES

CONTENTS

䡵 Emission Control System Maintenance . . . . . . . . 390
䡵 Emissions Testing . . . . . . . . . . . . . . . . . . . . . . . 390
䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 391

▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 394
▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 405
䡵 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . 410

M

390 MAINTENANCE SCHEDULES

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper func- tioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability. More frequent maintenance may be needed for vehicles in severe operating conditions such as dusty areas and very short trip driving. Inspection and service also should be done any time a malfunction is suspected. NOTE: Maintenance, replacement, or repair of the emis- sion control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part which has been certified pursuant to U.S. EPA or, in the State of Califor- nia, California Air Resources Board regulations.

EMISSIONS TESTING In some localities, it may be or will become a legal requirement to ensure that all emissions components and systems are functioning properly as a part of the test procedure. The test center accomplishes this by checking the On Board Diagnostic System (OBD) system with an electronic scan tool. If your vehicle has recently been serviced, the OBD system may have been reset to a ⬙not ready⬙ condition because the OBD system has not had sufficient time since the servicing to reconfirm that emissions components are operating properly. In most cases, a reasonable mix and amount of normal city and highway driving and at least one overnight-off period will be required to prepare your vehicle for this check; however your dealer has the equipment and procedures required to make certain that the OBD system of your vehicle is ready for the required testing.

MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high • Trailer towing. • Taxi, police, or delivery service (commercial service).

speeds during hot weather, above 90° F (32° C).

MAINTENANCE SCHEDULES 391

• Off-road or desert operation. • If equipped for and operating with E-85 (ethanol)

fuel.

If ANY of these apply to you then change your NOTE: engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. If ANY of these apply to you then change your NOTE: coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙B⬙. Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Sched- ule ⬙B⬙.

392 MAINTENANCE SCHEDULES

Use the schedule that best describes your driving condi- tions. Where time and mileage are listed, follow the interval that occurs first. NOTE: Under no circumstances should oil change in- tervals exceed 6000 miles (10 000 km) or 6 months whichever comes first.

CAUTION!

Failure to perform the required maintenance items may result in damage to the vehicle.

At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent and add if

required.

damage.

Once a Month • Check tire pressure and look for unusual wear or • Inspect the battery and clean and tighten the terminals • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed. • Check all lights and all other electrical items for correct

as required.

operation.

MAINTENANCE SCHEDULES 393

At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. • Inspect the brake hoses. • Inspect the CV joints (if equipped) and front suspen- • Check the automatic transmission fluid level. • Check the coolant level, hoses, and clamps.

sion components.

394 SCHEDULE “B”

Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high • Trailer towing.

speeds during hot weather, above 90° F (32° C).

• Taxi, police, or delivery service (commercial service). • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol)

fuel.

If ANY of these apply to you then change your NOTE: engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. If ANY of these apply to you then change your NOTE: coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual.

3,000
(5 000)

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect engine air cleaner filter, replace if neces- sary.

SCHEDULE “B” 395

6,000
(10 000)

9,000
(15 000)

12,000
(20 000)

15,000
(25 000)

M

396 SCHEDULE “B”

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary.**

18,000
(30 000)

21,000
(35 000)

27,000
(45 000)

24,000
(40 000)

30,000
(50 000)

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.

33,000
(55 000)

36,000
(60 000)

39, 000
(65 000)

SCHEDULE “B” 397

42,000
(70 000)

45,000
(75 000)

M

398 SCHEDULE “B”

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect and replace ignition cables if necessary (5.7L only).

51,000
(85 000)

48,000
(80 000)

57,000
(95 000)

54,000
(90 000)

60,000
(100 000)

Miles (Kilometers) Inspect auto tension drive belt and replace if re- quired. Drain and refill automatic transmission fluid, change filter (3.7L). This applies only if your ve- hicle is used for police, taxi, fleet, or frequent trailer towing. Drain and refill automatic transmission fluid and change main sump filter (4.7L/5.7L only). This ap- plies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing. Inspect transfer case fluid (4X4). Flush and replace engine coolant at 60 months, or 102, 000 miles (170 000 km) whichever comes first.

SCHEDULE “B” 399

48,000
(80 000)

51,000
(85 000)

54,000
(90 000)

57,000
(95 000)

60,000
(100 000)

M

400 SCHEDULE “B”

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Inspect auto tension drive belt and replace if re- quired.

63,000
(105 000)

66,000
(110 000)

69,000
(115 000)

72,000
(120 000)

75,000
(125 000)

Miles (Kilometers ) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if re- quired.

78,000
(130 000)

81,000
(135 000)

84,000
(140 000)

87,000
(145 000)

90,000
(150 000)

SCHEDULE “B” 401

402 SCHEDULE “B”

Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Flush and replace engine coolant, if not replaced at 60
months. Change rear axle fluid. Change front axle fluid (4X4).

93,000
(155 000)

99,000
(165 000)

102,000
(170 000)

96,000
(160 000)

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect and replace ignition cables if neces- sary (5.7L only). Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.

105,000
(175 000)

108,000
(180 000)

111,000
(185 000)

114,000
(190 000)

117,000
(195 000)

120,000
(200 000)

SCHEDULE “B” 403

M

404 SCHEDULE “B”

105,000
(175 000)

Miles (Kilometers) Drain and refill transfer case fluid (4X4). Drain and refill automatic transmission fluid, change filter (3.7L). This applies only if your vehicle is used for police, taxi, fleet, or fre- quent trailer towing. Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter if equipped. (4.7L/5.7L only). This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer tow- ing. Flush and replace engine coolant at 120
months, if not replaced at 102,000 miles (170
000 km). Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts.

108,000
(180 000)

111,000
(185 000)

114,000
(190 000)

117,000
(195 000)

120,000
(200 000)

Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace as neces- sary. Replace spark plugs.

SCHEDULE “A” 405

6,000
(10 000)

12,000
(20 000)

18,000
(30 000)

24,000
(40 000)

30,000
(50 000)

[6]

[12]

[24]

[18]

[30]

406 SCHEDULE “A”

Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Check transfer case fluid level (4X4). Flush and replace engine coolant at 60
months, if not replaced at 102,000 miles (170
000 km). Inspect brake linings.

36,000
(60 000)

42,000
(70 000)

48,000
(80 000)

54,000
(90 000)

60,000
(100 000)

66,000
(110 000)

[36]

[42]

[48]

[66]

[60]

[54]

Miles (Kilometers) [Months] Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary. * Inspect and replace ignition cables if neces- sary (5.7L only). Inspect auto tension drive belt and replace if required.

SCHEDULE “A” 407

36,000
(60 000)

[36]

42,000
(70 000)

[42]

48,000
(80 000)

[48]

54,000
(90 000)

[54]

60,000
(100 000)

66,000
(110 000)

[60]

[66]

M

408 SCHEDULE “A”

Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if re- quired.

72,000
(120 000)

78,000
(130 000)

84,000
(140 000)

90,000
(150 000)

96,000
(160 000)

[78]

[84]

[72]

[96]

[90]

Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Drain and refill tranfer case fluid (4X4). Flush and replace engine coolant, if not replaced at 60
months. Flush and replace engine coolant at 120 months, if not replaced at 102,000 miles (170 000 km). Inspect brake linings. Inspect engine air cleaner filter, replace as necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.**

SCHEDULE “A” 409

102,000
(170 000)

[102]

108,000
(180 000)

[108]

114,000
(190 000)

[114]

120,000
(200 000)

[120]