2007 Dodge Caravan Owners Manual

None None None None

at 12 in. (30 cm) In-

termittent

at 8 in. (20 cm) Con-

tinuous

162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

• Drivers must be careful when backing up even when using the Rear Park Sense System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death. • Before using the Rear Park Sense System, it is strongly recommended that the ball mount and hitch ball assembly be disconnected from the ve- hicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns the red LEDs ON. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.

CAUTION!

• To avoid vehicle damage the Rear Park Sense System should only be used as a parking aid and is unable to recognize every obstacle, including small objects. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity to the rear of the vehicle. • To avoid vehicle damage the vehicle must be driven slowly when using the Rear Park Sense System to be able to stop in time when an obstacle is detected. It is recommended that the driver look over his/her shoulder when using the Rear Park Sense System.

NOTE: • Ensure that the rear bumper is free of dirt and debris • Jackhammers, large trucks, and other vibrations could

to keep the system operating properly.

affect the performance of the system.

If “Service Park Sense System” appears in the Electronic Vehicle Information Center (EVIC) after making sure the rear bumper is clean please see your authorized dealer.

ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The switch is located on the right side of the steering column.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163

Adjustable Pedal Switch

Press the button forward to move the pedals forward (toward the front of the vehicle). Press the button rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF.

164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control System is ON. The following messages will be displayed on vehicles equipped with the Electronic Vehicle Information Sys- tem (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”).

CAUTION!

Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 30 mph (50 km/h).

Speed Control Switches

To Activate: Push the “ON/OFF” button once and the CRUISE indi- cator located below the instrument cluster odometer will illuminate showing the electronic speed control system is on. To turn the system OFF, push the “ON/OFF” button again and the system and indicator will turn off.

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165

To Set At A Desired Speed:

When the vehicle has reached the desired speed, press and release the “SET” button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate: A soft tap on the brake pedal, pushing the “CANCEL” button or normal braking while slowing the vehicle will deactivate the speed control without erasing the set speed memory. Pushing the “ON/OFF” button to the OFF position or turning off the ignition erases the set speed memory. To Resume Speed: To resume a previously set speed, push and release the “RESUME/ACCEL” button. Resume can be used at any speed above 25 mph (40 km/h).

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To Vary the Speed Setting: When the speed control is set, speed can be increased by pressing and holding the “RESUME/ACCEL” button. When the button is released, a new set speed will be established. Tapping the “RESUME/ACCEL” button once will result in a 2 mph (3 km/h) speed increase. Each time the button is tapped, speed increases so that tapping the button three times will increase speed by 6 mph (10 km/h), etc. To decrease speed while speed control is set, press and hold the “COAST” button. Release the button when the desired speed is reached, and the new speed will be set. Tapping the “COAST” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases.

To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Your vehicle will experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.

WARNING!

Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167

OVERHEAD CONSOLE — IF EQUIPPED The overhead console can contain courtesy/reading lights, an optional universal garage door opener (HomeLink威), compass/ temperature display, a mini-trip computer, optional elec- tronic vehicle information center (EVIC), power sliding door switches and an optional power liftgate switch.

sunglasses,

storage

for

Overhead Console

NOTE: To avoid unintentional operation of the power sliding doors from the rear seats, press the ON /OFF button located in the overhead console to disable the switches for the rear seat passengers.

168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Courtesy/Reading Lights

At the forward end of the console are two courtesy/ reading lights. Press the lens to turn these lights on. Press a second time to turn the lights off. The lights also turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry, the lights will also turn on when the unlock button on the transmitter is pressed. The area around the instrument panel cupholders is also illuminated from a light in the overhead console. This light is turned on when the headlight switch is on and will adjust in brightness when the dimmer control is rotated up or down.

Sunglass Storage At the rear of the overhead console, a compartment is provided for the storage of two pair of sunglasses. Press the door latch to open the compartment. The door will slowly rotate to an open position. Compass/Temperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing.

WARNING!

Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169

buttons for 10 seconds. Release the RESET button and complete three 360° turns in an area free from large metal objects. The “CAL” symbol will turn off and the compass will function normally.

CAUTION!

Do not place any external magnets, such as magnetic roof mount antennas, in the vicinity of the compass. Do not use magnetic tools when servicing the over- head console.

Automatic Compass Calibration This compass is self calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the “CAL” symbol will be displayed. After completing three 360° turns in an area free from large metal or metallic objects, the “CAL” symbol will turn off and the compass will function normally. Manual Compass Calibration If the compass appears erratic and the “CAL” symbol does not appear, you must put the compass into the Calibration Mode manually. To put into a Calibration Mode: Turn on the ignition switch and set the display to Comp/Temp. Press the RESET button on vehicles equipped with a Compass/ Mini Trip Computer for at least 10 seconds until the “CAL” symbol appears. On vehicles equipped with Compass/Temp press and hold the C/T and US/M

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set. NOTE: Magnetic materials should be kept away from the overhead console.

To set the variance: Turn the ignition switch ON and set the display to Comp/Temp. On vehicles equipped with a Compass/Mini Trip Computer press the RESET button for approximately 5 seconds. On vehicles equipped with Compass/Temp press and hold the C/T and US/M buttons for 5 seconds. The “VAR” symbol will light and the last variance zone number will be displayed. Press the STEP button on vehicles equipped with a Compass/ Mini Trip Computer or the US/M button on vehicles equipped with Compass/Temp to select the proper vari- ance zone as shown in the map. Press the RESET button on vehicles equipped with a Compass/Mini Trip Com- puter or the C/T button on vehicles equipped with Compass/Temp to set the new variance zone and resume normal operation.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171

Mini-Trip Computer This displays information on the following: • Average Fuel Economy (ECO AVG) Shows the average fuel economy since the last reset. • Distance To Empty (DTE) Shows the estimated distance that can be travelled with the fuel remaining in the tank. This estimated distance is determined using the MPG for the last few minutes. • Trip Odometer (ODO) Shows the distance travelled since the last reset. • Elapsed Time (ET) Shows the accumulated ignition ON time since the last reset. • Off Mode Shows a blank display.

172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• Step Button Push this button to cycle through all the Compass/Mini- trip Computer displays. • US/M Button Press this button to convert the display from U.S. to metric. To Reset The Display Pressing the Reset button once will clear the resettable function currently being displayed. Resettable functions are average fuel economy, trip odometer and elapsed time. Pressing the reset button twice within four seconds will clear all resettable functions. Reset will only occur if a resettable function is currently being displayed.

Electronic Vehicle Information Center (EVIC) — If Equipped The Electronic Vehicle Information Center, when the appropriate conditions exist, displays the following WARNING messages and symbols. Each message is accompanied by a single chime: • TURN SIGNALS ON (with graphic) • PERFORM SERVICE • DOOR AJAR (one or more, with graphic) • LIFTGATE AJAR (with graphic) • WASHER FLUID LOW (with graphic) • 1,2,3 OR 4 LOW TIRE(S) PRESSURE (Refer to ”Tire Pressure Monitor System” in the “Starting And Oper- ating, Tire Section”)

Equipped

• CHECK TPM SYSTEM (Refer to ”Tire Pressure Moni- tor System” in the “Starting And Operating, Tire Section”)

• MEMORY SEAT DISABLED (Not in Park) — If • ADJUSTABLE PEDAL DISABLED/CRUISE EN- • ADJUSTABLE PEDAL DISABLED/VEHICLE IN RE- • REAR PARK SENSE (Shown in Reverse only with a

GAGED

VERSE

single chime) — If Equipped

NOTE: Tire pressure menu items are available only on vehicles equipped with the Tire Pressure Monitor Sys- tem.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173

Customer Programmable Features — If Equipped Press the “MENU” button until one of the display choices following appears: Language When in this display you may select one of five lan- guages for all display nomenclature, including the trip computer functions. Press the “STEP” button while in this display selects English, Francaise, Deutsch, Italiano, or Espanol. As you continue the displayed information will be shown in the selected language. Rear Park Sense — If Equipped When this feature is selected the system scans for objects behind the vehicle using four sensors located in the rear bumper. Objects can be detected from up to 59 inches (150 cm). Pressing the “STEP” button while in this display will disable/enable the Rear Park Sense System.

174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

US or Metric Pressing the “STEP” button when in this display selects US or Metric. The overhead console and climate control displays will be in the selected units. Service Interval When this feature is selected a service interval between 2,000 miles (3 200 km) and 6,000 miles (9 600 km) in 500
mile (800 km) increments may be selected. Pressing the “STEP” button when in this display will select distances between 2,000 miles (3 200 km) and 6,000 miles (9 600
km) in 500 mile (800 km) increments. Reset Service Distance (Displays Only if Service Interval was Changed) When this feature is selected the current accumulated service distance can be reset to the newly selected service interval. Pressing the “STEP” button when in this display will select “Yes” or “No.”

Use Factory Settings If “Yes” is selected, all of the customer programmable features will be set to the factory default and not dis- played. If “No” is selected you can program the Vehicle Information Center to your own personal preferences. Auto Door Locks When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 18 mph (29 km/h). Pressing the “STEP” button when in this display will select “Yes” or “No.” Auto Unlock On Exit (Available Only When the AUTO DOOR LOCKS Feature is Turned On) When this feature is selected all the vehicle’s doors will unlock whenever any door is opened if the vehicle is stopped and the transmission is in “P” (Park) or “N” (Neutral) position. Pressing the “STEP” button when in this display will select “Yes” or “No.”

Remote Unlock Driver’s Door 1st When this feature is selected only the driver’s door will unlock on the first press of the remote keyless entry unlock button and require a second press to unlock the remaining locked doors and liftgate. When “REMOTE UNLOCK ALL DOORS” is selected all of the doors and the liftgate will unlock at the first press of the remote keyless entry unlock button. Pressing the “STEP” button when in this display will select “DRIVER’S DOOR 1ST” or “ALL DOORS”. Remote Linked To Memory (Available with Memory Seat and Pedals Only) When this feature is selected, pressing the Unlock button on any Remote Keyless Entry transmitter already linked to memory will return the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station presets to their memory set positions.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175

If this feature is not selected, the driver’s seat, driver’s mirror, adjustable pedals, and radio settings can only return to their memory set positions using the memory recall buttons (1 or 2) on the driver’s door panel. Any transmitter linked to memory will remain linked, but will not recall the memory positions. The transmitter memory recall function will operate again when this feature is selected. Refer to Driver Memory System for more information. Pressing the ⬙STEP⬙ button when in this mode will select between ⬙Yes⬙ or ⬙No⬙. Sound Horn On Lock When this feature is selected a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on LOCK/UNLOCK feature. Pressing the “STEP” button when in this display will select “Yes” or “No.”

176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Flash Lights On Lock/Unlock? When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter. This feature may be selected with or without the sound horn on lock feature selected. Pressing the “STEP” button when in this display will select “Yes” or “No.” Sliding Door Open Flash? When this feature is selected, and the sliding door(s) are opened, the left and right exterior hazard lights will flash for 12 seconds to alert other drivers in the area that passenger(s) could be entering or exiting the vehicle. Pressing the ⬙STEP⬙ button when in this display will select “Yes” or “No.” Headlamp Delay When this feature is selected the driver can choose, when exiting the vehicle, to have the headlamps remain on for

30, 60, or 90 seconds, or not remain on. Pressing the “STEP” button when in this display will select 30, 60, 90, or “OFF.” Headlamp On With Wipers (Available with Auto Headlights Only) When this feature is selected and the headlight switch has been moved to the “AUTO” position, the engine is running and, the front wipers are turned on for 10
seconds, the headlights will turn ON. The display will remain on Parade Mode (Daytime Brightness) for ease of viewing. Pressing the “STEP” button when in this display will select “Yes” or “No.” Power Accessory Delay When this feature is selected, accessory power will be supplied for up to 45 seconds for the power windows,

radio, power vent windows, power outlets, and remov- able center console, when the ignition switch is turned off or until the key is removed and either front door is opened.

GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed. NOTE: The HomeLink威 Universal Transceiver is dis- abled when the Vehicle Theft Alarm is active. For additional information on HomeLink威, call 1–800– 355–3515, or on the internet at www.homelink.com.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

WARNING!

A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards. This includes most garage door opener mod- els manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death. Call toll-free 1–800–355–3515
or, on the Internet at www.homelink.com for safety information or assistance.

178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Programming HomeLink

Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death.

WARNING!

Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.

NOTE: When programming a garage door opener, it is advised to park outside the garage. Some vehicles may require the ignition switch to be turned to the second (Accessory) position for programming and/or operation of HomeLink. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for more efficient train- ing and accurate transmission of the radio-frequency signal. 1. Press and hold the two outer HomeLink buttons, and release only when the indicator light begins to flash or the EVIC display shows “Channels Cleared” (after 20
seconds). Do not hold the buttons for longer than 30
seconds and do not repeat Step One to program a second and/or third hand-held transmitter to the remaining two HomeLink buttons.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179

3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until Step Four has been completed.

NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Pro- gramming⬙ section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from the slow to the rapid flash. 5. Press and hold the just trained HomeLink button and observe the indicator light or the EVIC display. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink button is pressed and released.

HomeLink Buttons

2. Position the end of your hand-held transmitter 1-3
inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view.

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: To program the remaining two HomeLink but- tons, begin with ⬙Programming⬙ Step Two. Do not repeat Step One.

If your hand-held transmitter appears to pro- NOTE: gram the universal transceiver, but your garage door does not operate using the transmitter and your garage door opener was manufactured after 1995, your garage door opener may have a multiple security code system (rolling code system). If your garage door is the “rolling code” type, please proceed to the heading “Program- ming A Rolling Code System.”

Programming A Rolling Code System

1. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙learn⬙ or ⬙smart⬙ button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.

2. Firmly press and release the ⬙learn⬙ or ⬙smart⬙ button. (The name and color of the button may vary by manu- facturer.) NOTE: There are 30 seconds in which to initiate Step Three. 3. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the ⴖpress/hold/releaseⴖ sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your equipped device. NOTE: To program the remaining two HomeLink but- tons, begin with ⬙Programming⬙ Step Two. Do not repeat Step One. For questions or comments, please contact HomeLink at www.homelink.com or 1-800-355-3515.

rolling code

Canadian Programming/Gate Programming Canadian radio-frequency laws require transmitter sig- nals to ⬙time-out⬙ (or quit) after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to ⬙time-out⬙ in the same manner. If you live in Canada or you are having difficulties programming a gate operator by using the ⬙Program- ming⬙ procedures (regardless of where you live), replace ⴖProgramming HomeLinkⴖ Step Three with the follow- ing: If programming a garage door opener or gate NOTE: operator, it is advised to unplug the device during the ⬙cycling⬙ process to prevent possible overheating. 3. Continue to press and hold the HomeLink button while you press and release every two seconds ⬙cycle⬙ your hand-held transmitter until the frequency signal has

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181

successfully been accepted by HomeLink. (The indicator light will flash slowly and then rapidly.) Proceed with ⬙Programming⬙ Step Four to complete. Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties or questions, contact HomeLink at: www.homelink.com or 1-800-355- 3515. Erasing HomeLink Buttons To erase programming from the three buttons (individual buttons cannot be erased but can be ⬙reprogrammed⬙ - note below), follow the step noted:

182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• Press and hold the two outer HomeLink buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30
seconds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙Programming⬙ - Step Two.

Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with ⬙Programming⬙ Step Two. For questions or comments, contact HomeLink at: www.homelink.com or 1-800-355-3515.

Security If you sell your vehicle, be sure to erase the frequencies by following the “Erasing HomeLink Buttons” instruc- tions in this section. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interference that may cause undes- ired operation.

NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink威 is a trademark owned by Johnson Controls, Inc.

In the event that you are still having programming difficulties, questions, or comments, contact HomeLink at: www.homelink.com or 1-800-355-3515.

POWER SUNROOF — IF EQUIPPED The power sunroof control is located between the sun visors on the overhead console.

Power Sunroof Controls

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

Press and hold the switch rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. Press and hold the button located to the right of the sunroof switch, to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward. Releasing the switch will stop the movement of the sunroof and the sunroof will remain in the partial vent position until the switch is pushed forward again. Express Open Feature During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. Again, momentarily pressing the switch rearward will activate the Express Open Feature.

184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To close the sunroof, hold the switch in the forward position. Again, any release of the switch will stop the movement and the sunroof will remain in a partial open condition until the switch is pushed forward again. The sunshade can be opened manually. It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open.

WARNING!

NEVER leave children alone in a vehicle. Occupants, particularly unattended children, can become en- trapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle

WARNING!

In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result.

Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with

the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.

ELECTRICAL POWER OUTLETS — IF EQUIPPED To the left of the instrument panel cup holder are two 12
volt power outlets. The upper outlet is controlled by the ignition switch and the lower outlet is connected directly to the battery. The upper outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package). A third outlet is located on the driver’s side, just to the rear of the sliding door and is also controlled by the ignition switch. The lower and rear outlets will not accommodate a conventional cigar lighter unit.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185

Rear Power Outlet

The outlets include tethered caps labeled with a key or battery symbol indicating the power source. The lower instrument panel outlet is powered directly from the battery, items plugged into this outlet may discharge the battery and/or prevent engine starting.

186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The lower outlet is protected by an automatic reset circuit breaker. The automatic circuit breaker restores power when the overload is removed. The circuit breaker also supplies power to the outlet in the removable floor console, when in the front position. Refer to section 3
“Removable Floor Console” in this manual. If desired, all of the power outlets can be NOTE: converted by your authorized dealer to provide power with the ignition switch in the OFF position.

Electrical Outlet Use With Engine Off

CAUTION!

• Accessories that draw higher power

• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these intermittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accesso- ries still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery. • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage.

CONVENIENCE TRAY DRAWER AND CUP HOLDERS

Instrument Panel Cup Holders The instrument panel cupholders are located in a pull out drawer just below the climate controls.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

When the drawer is pulled out firmly, the arms of the cupholders will spring out. Place the container to be held into one of the cupholders and then push the arm toward the container until the container is held stable. There are adjustable positions for the arm so the cupholder can accommodate a wide variety of container types and sizes, including those with handles. The arms of the cupholder can be adjusted in or out without damaging the detent mechanism. NOTE: Be sure the drawer is pulled out completely, otherwise the adjustable arm detents will not engage and the container will not be held stable.

Front Cupholders

188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Convenience Tray And Optional Smoker’s Package Kit Located between the instrument panel cupholders is a convenience tray that has been designed to hold miscel- laneous small items. NOTE: The convenience tray should never be used for ashes without the optional ash receiver in place. Perma- nent burn marks may result. With the optional dealer installed Smoker’s package, a removable ash receiver is inserted into the convenience tray location. To install the ash receiver, slide the forward edge into the convenience tray opening and push down to lock it into position. For cleaning of the ash receiver, its removal is accomplished by inserting the end of a key in the pry slot that is molded into the rear edge of the ash receiver and then twisting the key slightly.

Rear Cupholders There are dual stationary cupholders located in the passenger side rear trim panel and a single stationary cup holder on the driver side rear trim panel. There are also dual underseat cupholders for the 2nd seat passengers. With a bench seat in the 2nd seat position these cupholders slide out from under the center of the seat. If your vehicle is equipped with quad seats in the 2nd seat position, these cupholders are located on the out- board side of the seat pedestal.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189

• The quad seat cupholders are designed to break away if stepped on. To return the cupholder to its normal position, simply push the cupholder up to snap it into place. • The floor mat must be in position for optimum cup-

holder operation.

There are also two cupholders and a flat tray on the seat back of the quad seats. These can be used when the seat back is folded forward.

Quad Seat Cupholder

NOTE: • The quad seat cupholders will remain upright if the

seat is tilted forward.

190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

STORAGE

Front Seat Storage Bin — If Equipped The storage bin is located under the front passenger’s seat. If equipped with a lock, it can be locked with the ignition key.

Second Row Seat Storage bins — If Equipped The Seat Storage Bins are located on the floor in front of the second row seats, the area below the covers can be used for storage when the second row seat is in the upright position.

Front Seat Storage Bin

Storage Bin Cover Lock Release

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191

Overhead Rail System — If Equipped The overhead rail system contains provisions for three movable and removable overhead storage bins. The storage bins may be placed anywhere on the overhead rail system.

CAUTION!

Do not load objects over 1.5 lbs (0.68 kg) in the storage bins. Failure to follow this could cause damage to the Overhead Rail System.

Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the ⬙Unlocked⬙ position to allow greater access to the storage bin.

CAUTION!

NOTE: The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

WARNING!

In an accident, serious injury could result if the seat storage bin covers are not properly latched. Do not drive the vehicle with the storage bin cover open. Keep the storage bin cover closed and latched while the vehicle is in motion. Do not operate the storage bin cover while the vehicle is in motion.

192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To Remove Storage Bins

1. Support the bin with one hand and pull the latch handles out.

2. Twist the latch handles a 1⁄4 turn and pull outward to disengage the bin from the rail.

3. Remove the storage bin. NOTE: Make sure the latch handle pops out before removing the storage bin. To reinstall the storage bins, place the bin in the desired location on the overhead rail, push firmly upward on the bin with one hand, while pushing in on the latch handle,

twist a 1⁄4 turn to attach the bin to the rail. Push the latch handle down to lock the storage bin in place.

WARNING!

In a collision, you or others in your vehicle could be injured if the storage bins are not properly latched to the Overhead Rail System. Always be sure the storage bins are fully latched.

Removable Floor Console With Stow ’n Go Seating — If Equipped The removable floor console has a two power outlets, storage tray, light, removable cell phone holder, tissue holder, pen holder and a map holder. It can be removed from the vehicle by pulling the release handle inside the floor console. To remove the console use the following procedure:

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193

1. Open the console lid and remove the storage tray. 2. Pull up on the release handle located inside the floor console, and slide the console rearward to disengage from the floor.

Stow ’n Go Center Console Release Handle

3. Remove the floor console.

194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To reinstall the console, open the console lid and remove the storage tray. Pull up on the release handle and slide the console forward to engage the front of the console into the floor tray. Pivot the floor console down until it is seated on the floor tray and release the handle. Pull up on the console to be sure it is firmly attached.

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

Cell Phone Holder Removal

1. Open the floor console lid and lift the cell phone holder upward.

2. Squeeze the legs together to disengage the holder from the floor console and remove the cell phone holder. To reinstall the cell phone holder, align the pivot legs into the guides and push forward to snap the legs into place. Removable Floor Console Without Stow ’n Go Seating — If Equipped The removable floor console has a power outlet, storage tray, light, cell phone holder, tissue holder, and a map holder. It can be placed between either the front seats or middle seats. NOTE: When the console is located between the front seats the outlet is protected by an automatic circuit breaker and is powered directly from the battery, items plugged into this outlet may discharge the battery and/or prevent engine starting.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195

Removable Floor Console

To remove the console use the following procedure: 1. Open the rear lid and remove the storage tray. 2. Pull up on the release handle located inside the floor console to disengage the floor console, reinstall the storage tray and close the rear lid.

Removable Floor Console Release Handle

3. Using the front and rear grab handles, slide the console rearward to disengage the front of the console and lift up to remove the console from the floor. 4. Place the rubber mat on the floor tray.

196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To reinstall the console, remove the rubber mat and relocate to the alternate floor tray, slide the console forward to engage the front of the console into the floor tray. Rapidly push down on the rear of the console with enough force to engage the latch, you should hear the latch “snap” into place. Pull up on the console to be sure it is firmly attached.

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

NOTE: When the removable floor console is located between the middle seats, the power outlet only has power supplied to it when the ignition switch is ON.

Cell Phone Holder

1. Open the front lid and remove the cell phone holder by pulling rearward and up on the lower edge of the holder.

Cell Phone Holder

2. Plug in the power cord for the cellular phone into the outlet located in the bottom of the forward console bin and reinstall the cell phone holder. 3. Place the cell phone into the holder.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197

CAUTION!

• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.

198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Rear Compartment Storage Bins Your vehicle may be equipped with open storage bins located in each rear trim panel. Cargo/Tub Net A cargo/tub net is available on vehicles equipped with Stow ’n Go Seating. The cargo net fits in the second row storage bin or the third row tub. The net is supported by hooks located in these areas. Refer to instructions pro- vided in the net kit. Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.

Cargo Area Storage The seats in your vehicle are in-line which enables you to stow long objects, such as lumber or skis, on the floor without moving the seats. NOTE: With all rear seat backs folded, a 4 x 8 foot sheet of building material may be stored in the long-wheelbase body style on top of the folded seats with the liftgate closed. The front seats must be moved slightly forward of the rearmost position. If the rear seats are removed no front seat adjustment is needed and more than one 4 x 8
sheet of building material may be stored. The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199

Rear Cargo Area Loading Limit

Roof Rack

ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 68 kg (150 lbs), and should be uniformly distributed over the luggage rack crossbars.

Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity.

200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To move the cross bars, loosen the thumb screws located at the upper edge of each cross bar approximately six turns, then move the cross bar to the desired position, keeping the crossbars parallel to the rack frame. Once the cross bar is in place, retighten the thumb screws to lock the cross bar into position. Attempt to move the crossbar again to ensure that it has properly locked into position. NOTE: To help control wind noise when installing the cross bars make sure that the arrows marked on the front side of the cross bars are facing the front of the vehicle. Also, when the cross bars are not in use the notch on the cross bars should be aligned with the arrows on the side rails. This will help reduce the amount of wind noise when the crossbars are not in use. The tie down holes on the cross bar ends should always be used to tie down the load. Check the straps frequently to be sure that the load remains securely attached.

CAUTION!

• Crossbars should remain equally spaced or parallel at any luggage rack position for proper function. Noncompliance could result in damage to the lug- gage rack, cargo and/or vehicle. • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately. • Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to loads. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.

WARNING!

Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.

LOAD LEVELING SYSTEM The automatic load leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201

If the leveled vehicle is not moved for approximately 15
hours, the leveling system will bleed itself down. The vehicle must be driven to reset the system.

WARNING!

Do not install the load leveling system on vehicles that are not equipped with Anti-Lock Brakes. Ve- hicles without Anti-Lock Brakes (ABS) have a height-sensing proportioning valve. Installing a lev- eling system will render this system ineffective, inappropriately reducing rear brake pressure, result- ing in increased stopping distances. You could have an accident.

UNDERSTANDING YOUR INSTRUMENT PANEL

CONTENTS

䡵 Instrument Panels And Controls . . . . . . . . . . . . 208
䡵 Base Instrument Cluster . . . . . . . . . . . . . . . . . . 209
䡵 Instrument Cluster With Tach . . . . . . . . . . . . . . 210
䡵 Instrument Cluster Descriptions . . . . . . . . . . . . 211
䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . . 220
▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 220
䡵 Radio General Information . . . . . . . . . . . . . . . . 220
▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . 220
▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 221
▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 221

▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 221
▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 221

䡵 Sales Code RAZ — AM/ FM Stereo Radio With

Cassette Tape Player, CD Player And CD Changer Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
▫ Operating Instructions — Radio . . . . . . . . . . . 222
▫ Power Switch, Volume Control . . . . . . . . . . . . 222
▫ Seek Button (Radio Mode) . . . . . . . . . . . . . . . 222
▫ Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
▫ Radio Data System (RDS) . . . . . . . . . . . . . . . 223

204 UNDERSTANDING YOUR INSTRUMENT PANEL

▫ PTY (Program Type) Button . . . . . . . . . . . . . . 223
▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
▫ Fade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
▫ Tone Control . . . . . . . . . . . . . . . . . . . . . . . . 225
▫ AM/FM Selection . . . . . . . . . . . . . . . . . . . . . 225
▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 225
▫ To Set The Radio Push-Button Memory . . . . . . 226
▫ To Change From Clock To Radio Mode . . . . . . 226
▫ Operating Instructions — Tape Player . . . . . . . 226
▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 226
▫ Fast Forward (FF) . . . . . . . . . . . . . . . . . . . . . 227
▫ Rewind (RW) . . . . . . . . . . . . . . . . . . . . . . . . 227
▫ Tape Eject . . . . . . . . . . . . . . . . . . . . . . . . . . . 227

▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 227
▫ Changing Tape Direction . . . . . . . . . . . . . . . . 227
▫ Metal Tape Selection . . . . . . . . . . . . . . . . . . . 227
▫ Pinch Roller Release . . . . . . . . . . . . . . . . . . . 228
▫ Noise Reduction . . . . . . . . . . . . . . . . . . . . . . 228
▫ Operating Instructions — CD Player . . . . . . . . 228
▫ Inserting The Compact Disc . . . . . . . . . . . . . . 228
▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 229
▫ EJT CD (Eject) Button . . . . . . . . . . . . . . . . . . 229
▫ FF/Tune/RW . . . . . . . . . . . . . . . . . . . . . . . . 230
▫ Program Button 4 (Random Play) . . . . . . . . . . 230
▫ Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
▫ Tape CD Button . . . . . . . . . . . . . . . . . . . . . . 230

▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 231
▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 231
▫ CD Changer Control Capability —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 231

䡵 Sales Code REV — AM & FM Stereo Radio With

CD Player And CD/DVD Changer Controls . . . . 232
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 233
▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 237
▫ CD/DVD Changer Operation . . . . . . . . . . . . . 238
▫ Notes On Playing MP3 Files . . . . . . . . . . . . . 239
▫ Operation Instructions - (CD Mode For MP3

Audio Play)

. . . . . . . . . . . . . . . . . . . . . . . . . 241

▫ Operating Instructions — MP3 Player, Portable

Walkman . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

UNDERSTANDING YOUR INSTRUMENT PANEL 205

▫ Operating Instructions — Video

Games/Camcorders

. . . . . . . . . . . . . . . . . . . 242

䡵 Sales Code RBQ — AM/FM Stereo Radio With

6 - Disc CD Changer . . . . . . . . . . . . . . . . . . . . 243
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 244
▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 246

䡵 Sales Code RBK — AM/ FM Stereo Radio With

CD Player And CD Changer Controls . . . . . . . . 251
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 251
▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 253
▫ CD Changer Control Capability — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 255

䡵 Sales Code RB1 — AM/FM Stereo Radio With

DVD/GPS Navigation System . . . . . . . . . . . . . . 257

206 UNDERSTANDING YOUR INSTRUMENT PANEL

▫ Operating Instructions — Radio . . . . . . . . . . . 258
▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 258
䡵 6 Disc CD/DVD Changer (RDV) — If Equipped . 259
▫ Operating Instructions — CD/DVD Changer . . 260
▫ Eject (EJT) Button . . . . . . . . . . . . . . . . . . . . . 262
▫ Remote Control Operating Instructions . . . . . . 262
▫ Operating Instructions — Video Screen . . . . . . 266
▫ Operating Instructions — Headphones . . . . . . 268
▫ Operating Instructions — MP3 Player, Portable

Walkman . . . . . . . . . . . . . . . . . . . . . . . . . . . 270

▫ Operating Instructions — Video

Games/Camcorders

. . . . . . . . . . . . . . . . . . . 270
䡵 Satellite Radio — If Equipped . . . . . . . . . . . . . . 271
▫ System Activation . . . . . . . . . . . . . . . . . . . . . 271

▫ Electronic Serial Number/Sirius Identification

Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 271

▫ Selecting Satellite Mode In RAH And

RBK Radios . . . . . . . . . . . . . . . . . . . . . . . . . 272

▫ Selecting Satellite Mode In RBU, RAZ, RB1 And

RBQ Radios . . . . . . . . . . . . . . . . . . . . . . . . . 272
▫ Selecting a Channel . . . . . . . . . . . . . . . . . . . . 272
▫ Storing And Selecting Pre-Set Channels . . . . . . 273
▫ Using The PTY (Program Type) Button — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
▫ PTY Button ⬙Scan⬙ . . . . . . . . . . . . . . . . . . . . . 273
▫ PTY Button ⬙Seek⬙ . . . . . . . . . . . . . . . . . . . . . 274
▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 274
▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 274

䡵 Radio Operation And Cellular Phones . . . . . . . . 274
䡵 Remote Sound System Controls — If Equipped . . 275
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 276
▫ Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . 276
▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 276
䡵 Cassette Tape And Player Maintenance . . . . . . . 276
䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . . 277
䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 278

▫ Manual Air Conditioning And Heating

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
▫ Front Mode Control . . . . . . . . . . . . . . . . . . . 280
▫ Manual Air Conditioning Operation . . . . . . . . 284
▫ Manual Rear Zone Climate Control —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 286

UNDERSTANDING YOUR INSTRUMENT PANEL 207

▫ Automatic Temperature Control —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 289
䡵 Rear Window Features . . . . . . . . . . . . . . . . . . . 301

▫ Intermittent Rear Wiper Operation — Manual

Temperature Control Only . . . . . . . . . . . . . . . 301

▫ Rear Washer Operation — Manual Temperature

Control Only . . . . . . . . . . . . . . . . . . . . . . . . 302

▫ Rear Wiper Operation — Automatic Temperature

Control Only . . . . . . . . . . . . . . . . . . . . . . . . 303

▫ Intermittent Rear Wiper Operation — Automatic

Temperature Control Only . . . . . . . . . . . . . . . 303
▫ Rear Washer Operation — Automatic Temperature Control Only . . . . . . . . . . . . . . . . . . . . . . . . 303

▫ Electric Rear Window Defroster —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 304

208 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT PANELS AND CONTROLS

BASE INSTRUMENT CLUSTER

UNDERSTANDING YOUR INSTRUMENT PANEL 209

210 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER WITH TACH

INSTRUMENT CLUSTER DESCRIPTIONS

1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Tire Pressure Monitoring Telltale Lamp — If Equipped

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when

UNDERSTANDING YOUR INSTRUMENT PANEL 211

one or more of your tires is significantly underinflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. NOTE: The Tire Pressure Monitoring System (TPMS) is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. The Tire Pressure Monitoring Telltale Lamp will illumi- nate in the instrument cluster, and an audible chime will be activated when one or more tire pressures is low. The TPMS Telltale Lamp will flash on and off for 60 seconds

212 UNDERSTANDING YOUR INSTRUMENT PANEL

when a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset.

CAUTION!

The Tire Pressure Monitoring System (TPMS) has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your ve- hicle. Undesirable system operation or sensor dam- age may result when using replacement equipment that is not of the same size, type, and / or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

3. Low Fuel Light

When the fuel level reaches approximately 3.0
gallons (11.0 liters) this light will turn on and remain on until fuel is added.

4. Turn Signal Indicators

The arrow will flash with the exterior turn signal when the turn signal lever is operated.

If the vehicle electronics sense that the vehicle has traveled about one mile with the turn signals on, a chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 5. Liftgate Ajar

This light turns on if the liftgate is not com- pletely closed.

6. Door Ajar Light

This light turns on if a door is not completely closed.

7. Speedometer Indicates vehicle speed. 8. Brake System Warning Light

This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, there is a low brake fluid level or there is a problem with the anit-lock brake system. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.

UNDERSTANDING YOUR INSTRUMENT PANEL 213

The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level condi- tions. The vehicle should have service performed. If brake failure is indicated, immediate repair is neces- sary.

WARNING!

Driving a vehicle with the brake light on is danger- ous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.

214 UNDERSTANDING YOUR INSTRUMENT PANEL

Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately four seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application.

9. Airbag Light

This light turns on and remains on for 6 to 8
seconds as a bulb check when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. 10. Anti-Lock Light

This light monitors the Anti-Lock Brake Sys- tem. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.

If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on.

If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer. 11. Tachometer — If Equipped The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 12. Voltage Light

This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained.

UNDERSTANDING YOUR INSTRUMENT PANEL 215

13. Seat Belt Reminder Light

When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s and/or the occupied front passenger’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s and/or the occupied front passenger’s seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously. Refer to ⬙Enhanced Driver Seat Belt Reminder System (BeltAlert™)⬙ in the Occupant Restraints section for more information. 14. Engine Temperature Warning Light

This light warns of an overheated engine condi- tion. If the engine is critically hot, a continuous chime will sound for 4 minutes. After the chime turns off, the engine will still be critically hot until the light turns off.

216 UNDERSTANDING YOUR INSTRUMENT PANEL

15. Vehicle Theft Alarm Light — If Equipped

This light will flash for approximately 15 sec- onds when the vehicle theft alarm is arming.

16. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.

CAUTION!

Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H“, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, and you hear continuous chimes, turn the engine off immediately, and call for service.

WARNING!

A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph.

17. Washer Fluid Light

This light turns on when the washer fluid level falls below approximately 1/4 filled. The light will remain on until fluid is added.

18. Transmission Range Indicator This display indicator shows the automatic transaxle gear selection.

UNDERSTANDING YOUR INSTRUMENT PANEL 217

NOTE: You must apply the brakes before shifting from Park. 19. Oil Pressure Warning Light

This light shows low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for 4 minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. 20. High Beam Light

This light shows that the headlights are on high beam. Pull lever towards the steering wheel to switch the headlights from high or low beam.

the turn signal

218 UNDERSTANDING YOUR INSTRUMENT PANEL

21. Malfunction Indicator Light

This light is part of an onboard diagnostic system called OBD that monitors engine and automatic transmission control systems. The light will illu- minate when the key is in the ON position before engine start. If the bulb does not come when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing. The Malfunction Indicator Light flashes to alert to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs.

22. Trac Off Indicator — If Equipped This display indicator should illuminate for approxi- mately four seconds as a bulb check when the ignition switch is first turned ON. The “TRAC OFF” Indicator will flash if the traction control is in use. The “TRAC OFF” Indicator will illuminate if: • The Traction Control switch has been used to turn • There is a Traction Control System malfunction • The system has been deactivated to prevent damage to the brake system due to overheated brake tem- peratures.

the system OFF.

NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the TRAC and the OFF indicators located in the instrument cluster.

This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the TRAC and the OFF indicators. If your vehicle becomes stuck in mud, ice, or snow, turn the Traction Control System OFF before attempting to “rock” the vehicle free. 23. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined.

UNDERSTANDING YOUR INSTRUMENT PANEL 219

The trip odometer shows individual trip mileage. To switch from odometer to trip odometer, press the Trip Odometer button. Loose Fuel Filler Cap If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, GASCAP will be displayed in the instrument cluster odometer. Tighten the fuel filler cap properly and press the odometer reset button to turn the GASCAP message off. If the problem continues, the message will appear the next time the vehicle is started. See Section 7 of this manual for more information. 24. Cruise Indicator This display indicator shows that the Speed Control System is ON.

220 UNDERSTANDING YOUR INSTRUMENT PANEL

25. Trip Odometer Button Press this button to change the display from odometer to trip odometer. The word TRIP will appear when in the trip odometer mode. Push in and hold the button for two seconds to reset the trip odometer to 0 miles or kilometers. The odometer must be in trip mode to reset.

ELECTRONIC DIGITAL CLOCK

Clock Setting Procedure

1. Turn the ignition switch to the ON or ACC position and press the time button. Using the tip of a ballpoint pen or similar object, press either the hour (H) or minute (M) buttons on the radio. 2. Press the H button to set hours or the M button to set minutes. The time setting will increase each time you press a button.

The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position and the time button is pressed. When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping is accurately maintained.

RADIO GENERAL INFORMATION

Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help

you understand and save you concern about these “ap- parent” malfunctions, you must understand a point or two about the transmission and reception of radio sig- nals. Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal.

UNDERSTANDING YOUR INSTRUMENT PANEL 221

AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. NOTE: The radio, steering wheel radio controls (if equipped), and 6 disc CD/DVD changer (if equipped) will remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature.

222 UNDERSTANDING YOUR INSTRUMENT PANEL

SALES CODE RAZ — AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS

NOTE: The radio sales code is located on the lower left side of your radio faceplate.

RAZ Radio

Operating Instructions — Radio

NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. Holding the button will by pass stations until you release the button.

Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Radio Data System (RDS)

The Radio Data System allows radio broadcasting sta- tions to send data signals on a subcarrier frequency which is added to the stereo signal. RDS was developed to give FM receivers user-friendly features, such as Program Service name (PS) and Program Type (PTY). Program Service name is typically used by the broad- caster to display the station’s name or call letters, for example ⬙WNIC⬙. Typically these are 8 characters in length and are displayed by the radio for those stations

UNDERSTANDING YOUR INSTRUMENT PANEL 223

which are broadcasting this information. PTY (Program Type) is used to characterize the station’s program ma- terial, for example ⬙Rock Music⬙. PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broad- cast PTY information. Toggle the PTY button to select the following format types:

Program Type

Radio Display

Adult Hits Classical Classic Rock College

Adult Hits Classical Classic Rock College

224 UNDERSTANDING YOUR INSTRUMENT PANEL

Program Type

Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues

Radio Display

Program Type

Radio Display

Country Inform Jazz Language News Nostalgia Oldies Personality Public R & B Religious Music Religious Talk Rock Soft Soft Rock Soft R&B

Sports Talk Top 40
Weather

Sports Talk Top 40
Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.

Pressing PTY, then SCAN will scan the FM Band and stop at all RDS stations. Each RDS station will be played for a 5 second scan once around the FM Band and stop at the last station. The PTY icon will then turn off. Balance The Balance control adjusts the left-to-right speaker bal- ance. Push in the button and it will pop out. Adjust the balance and push the button back in. The balance will be displayed and continuously updated while the button is turned. Fade The Fade control provides for balance between the front and rear speakers. Push in the button and it will pop out. Adjust the balance and push the button back in. The fade will be displayed and continuously updated while the button is turned.

UNDERSTANDING YOUR INSTRUMENT PANEL 225

Tone Control Slide the Bass and/or Treble controls up or down to adjust the sound for the desired tone. The treble, and bass will be displayed and continuously updated while the slide is moved. AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5
seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band.

226 UNDERSTANDING YOUR INSTRUMENT PANEL

To stop the search, press SCAN a second time. To Set The Radio Push-button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button. If a station is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into memory. You can recall the stations stored in SET 2 memory by pressing the push- button twice.

To Change From Clock To Radio Mode Press the Time button to change the display between radio frequency and time. Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation. Sometimes poor playback may be experienced due to a defective cassette tape. Clean and demagnetize the tape heads at least twice a year. Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection.

Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed again or the end of the tape is reached. At the end of the tape, the tape will play in the opposite direction. Rewind (RW) Press the RW button momentarily to reverse the tape direction. The tape will reverse until the button is pressed again or until the end of the tape is reached. At the end of the tape, the tape will play in the opposite direction.

UNDERSTANDING YOUR INSTRUMENT PANEL 227

Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button. The lighted arrow in the display window will show the new direction. Metal Tape Selection If a standard metal tape is inserted into the player, the player will automatically select the correct equalization and the 70 symbol will appear in the display window.

228 UNDERSTANDING YOUR INSTRUMENT PANEL

Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play. Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. To turn off the Dolby Noise reduction System: Press the Dolby button (button 2) after you insert the tape. The NR light in the display will go off when the Dolby System is off. The Dolby System is automatically reactivated each time a tape is inserted. * ”Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Labo- ratories Licensing Corporation.

Operating Instructions — CD Player

NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.

CAUTION!

This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.

Inserting The Compact Disc The CD player contained within the radio is not a multi-disc changer, and will only accept one CD. Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player.

If the volume control is ON, the unit will switch from radio to CD mode and begin to play. The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. NOTE: • You may eject a disc with the radio OFF. The ignition switch must be in the ON or ACC position to insert a disc with the radio OFF. • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player and the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out.

UNDERSTANDING YOUR INSTRUMENT PANEL 229

Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT CD (Eject) Button Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear. The disc can be ejected with the radio OFF.

230 UNDERSTANDING YOUR INSTRUMENT PANEL

FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW (Reverse) button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play. This feature plays the tracks on the se- lected disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press TUNE FF to fast forward through the tracks. Press the FF button a second time to stop the fast forward feature. If TUNE RW is pressed, the current track will reverse to the beginning of the track and begin playing. Press button 4 a second time to stop Random Play.

MODE Press the MODE button to select between the tape player, CD player, or satellite radio (if equipped). To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds. The current program type and channel number will then be displayed for five seconds. The current channel name and number will then be displayed until an action occurs. A CD or tape may remain in the player while in the Satellite Radio mode. Tape CD Button Press this button to select between CD player and Tape player.

Time Button Press this button to change the display from elapsed CD playing time to time of day. Scan Button Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The fol- lowing instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Disc Up/Program Button 1
Press the DISC up (button 1) button to play the next available disc.

UNDERSTANDING YOUR INSTRUMENT PANEL 231

Disc Down/Program Button 5
Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated. Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer.

• Water condensation on optics SALES CODE REV — AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS

NOTE: The radio sales code is located on the lower left side of your radio faceplate.

232 UNDERSTANDING YOUR INSTRUMENT PANEL

CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display. A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc

UNDERSTANDING YOUR INSTRUMENT PANEL 233

NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. PTY (Program Type) Pressing the INFO button once while in FM mode will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out, the PTY icon will turn off. Pressing the TUNE button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information. Toggle the TUNE button to select the following format types:

Program Type

Radio Display

Adult Hits Classical Classic Rock College

Adult Hit Classical Classic Rock College

Radio Operation

REV Radio

Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume.

234 UNDERSTANDING YOUR INSTRUMENT PANEL

Program Type

Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues

Radio Display

Program Type

Radio Display

Country Inform Jazz Language News Nostalgia Oldies Personality Public R & B Religious Music Religious Talk Rock Soft Soft Rock Soft R & B

Sports Talk Top 40
Weather

Sports