2015 Chevrolet Traverse Owners Manual

Vehicle Care

Warning (Continued)

parts. The area damaged by the tire chains could cause loss of control and a crash. Use another type of traction device only if its manufacturer recommends it for the vehicle's tire size combination and road conditions. Follow that manufacturer's instructions. To avoid vehicle damage, drive slow and readjust or remove the traction device if it contacts the vehicle. Do not spin the wheels. If traction devices are used, install them on the front tires.

{ Warning

Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.

If a Tire Goes Flat It is unusual for a tire to blow out while driving, especially if the tires are maintained properly. See Tires on page 10-35. If air goes out of a tire, it is much more likely to leak out slowly. But if there ever is a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (57,1)

{ Warning

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-3.

{ Warning Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall causing injury or death. Find a level place to change the tire. To help prevent the vehicle from moving:

1. Set the parking brake firmly. 2. Put an automatic

transmission in P (Park) or a manual transmission in 1 (First) or R (Reverse).

3. Turn off the engine and do not restart while the vehicle is raised.

4. Do not allow passengers to

remain in the vehicle.

5. Place wheel blocks,

if equipped, on both sides of the tire at the opposite corner of the tire being changed.

Vehicle Care

10-57

When the vehicle has a flat tire (2), use the following example as a guide to assist in the placement of the wheel blocks (1), if equipped.

1. Wheel Block (If Equipped) 2. Flat Tire

The following information explains how to repair or change a tire.

Tire Changing

Removing Tools The tools needed to remove the spare tire are located in the storage compartment on the driver side, at the rear of the vehicle.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (58,1)

10-58

Vehicle Care

4. Turn the jack on its side, with the

bottom facing toward you.

5. Pull the jack straight out, bottom

first.

Removing the Spare Tire The compact spare tire is located under the vehicle, in front of the rear bumper. See Compact Spare Tire on page 10-66 for more information.

1. Tool Bag 2. Wing Bolt 3. Jack

1. Open the jack storage

compartment by pulling on the latch tab, located toward the rear of the vehicle, and pulling the cover off.

1. Jack 2. Wrench (Three-Piece Shown,

One-Piece Similar)

2. Remove the wing bolt (2) by turning it counterclockwise.

The tools you will be using include the jack (1) and wrench (2).

3. Push the jack (3) up out of the

holding bracket and remove the tool bag (1).

1. Rear Convenience Center 2. Wrench (Three-Piece Shown,

One-Piece Similar)

3. Carpet Cutout 4. Hoist Shaft 5. Compact Spare Tire 6. Retainer

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (59,1)

1. Open the storage compartment

5. Tilt the retainer and slip it

2.

door of the convenience center (1) that is nearest the liftgate.

2. Open the carpet cutout (3) that

is located through the hole of the storage compartment.

3. Attach the wrench (2) into the

hoist shaft (4).

4. Turn the wrench (2)

counterclockwise to lower the spare tire (5) to the ground. Continue turning the wrench until the spare tire can be pulled out from under the vehicle.

through the wheel opening to remove the spare tire from the cable.

6. Turn the wrench clockwise to raise the cable back up after removing the spare tire. Do not store a full-size or a flat road tire under the vehicle. See “Storing the Spare Tire” and “Storing the Flat Tire” later in this section.

Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before

proceeding. See If a Tire Goes Flat on page 10-56 for more information.

Vehicle Care

10-59

If the vehicle has a wheel cover, loosen the plastic nut caps with the wheel wrench. They will not come off. Then, using the flat end of the wheel wrench, pry along the edge of the cover until it comes off. Be careful; the edges may be sharp. Do not try to remove the cover with your bare hands. Store the wheel cover securely in the rear of the vehicle until you have the flat tire repaired or replaced. If the vehicle has aluminum wheels, remove the wheel nut caps using the wheel wrench.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (60,1)

10-60

Vehicle Care

Caution (Continued)

damaged. Do not use an impact wrench to remove the wheel nuts if this vehicle has wheel locks.

4. To identify the appropriate

jacking location, find the triangle or rectangular notch about 30.5 cm (12 in) from the front tire or about 27 cm (10.5 in) from the rear tire.

Triangle Shown, Without Similar

The triangle may be located near each wheel on the vehicle's exterior.

{ Caution

If a jack is used to raise the vehicle without positioning it correctly, the vehicle could be damaged. When raising the vehicle on a jack, avoid contact with the rear axle control arms.

3. Loosen the wheel nuts — but do

not remove them — using the wrench. For wheels with a wheel lock key, use the wheel lock key between the lock nut and wrench. The key is supplied in the front passenger door pocket.

{ Caution

If this vehicle has wheel locks and an impact wrench is used to remove the wheel nuts, the lock nut or wheel lock key could be

(Continued)

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (61,1)

Vehicle Care

10-61

5. Attach the wrench to the jack,

and turn the wrench clockwise to raise the jack head 7.6 cm (3 in). 6. Do not raise the vehicle yet. Put the compact spare tire near you.

{ Warning

Getting under a vehicle when it is lifted on a jack is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

Warning (Continued)

damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

7. Raise the vehicle by turning the

wrench clockwise in the jack. Raise the vehicle far enough off the ground so that there is enough room for the spare tire to fit under the wheel well.

8. Remove all the wheel nuts and

the flat tire.

{ Warning

Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle

(Continued)

9. Remove the plastic spare tire

heat shield by pulling the rubber latch. Store the plastic spare tire heat shield. See “Storing the Spare Tire” later in this section for more information. { Warning

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When

(Continued)

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (62,1)

{ Caution

Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 12-2 for the wheel nut torque specification.

10-62

Vehicle Care

Warning (Continued)

changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

{ Warning

Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.

10. Remove any rust or dirt from

the wheel bolts, mounting surfaces, and spare wheel. 11. Place the spare tire on the

wheel mounting surface.

12. Put the nuts on by hand by

turning them clockwise until the wheel is held against the

mounting surface. Make sure the rounded end is toward the wheel.

13. Lower the vehicle by attaching

the wrench to the jack and turning the wrench counterclockwise. Lower the jack completely.

{ Warning

Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12-2 for original equipment wheel nut torque specifications.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (63,1)

14. Tighten the wheel nuts firmly in

a crisscross sequence, as shown.

{ Caution

Wheel covers will not fit on the vehicle's compact spare. If you try to put a wheel cover on the compact spare, the cover or the spare could be damaged.

Storing the Spare Tire { Warning

The underbody-mounted spare tire needs to be stored with the valve stem pointing down. If the spare tire is stored with the valve stem pointing upwards, the secondary latch will not work properly and the spare tire could loosen and suddenly fall from the vehicle. If this happened when

(Continued)

Warning (Continued)

the vehicle was being driven, the tire might contact a person or another vehicle, causing injury and damage to itself. Be sure the underbody-mounted spare tire is stored with the valve stem pointing down.

{ Warning

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

To store the spare tire: 1. Lay the compact spare tire near

the rear of the vehicle with the valve stem down.

Vehicle Care

10-63

2. Reinstall the plastic spare tire

heat shield on the compact spare tire.

3. Slide the cable retainer through the center of the wheel and start to raise the compact spare tire. Make sure the retainer is fully seated across the underside of the wheel.

4. When the compact spare tire is

almost in the stored position, turn the tire so the valve is toward the rear of the vehicle. This position helps when checking the air pressure in the compact spare tire.

5. Raise the tire fully against the

underside of the vehicle. Continue turning the wrench until you feel more than two clicks. This indicates that the compact spare tire is secure and the cable is tight. The spare tire hoist cannot be overtightened.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (64,1)

10-64

Vehicle Care

Storing the Flat Tire

3. Put the flat tire in the rear

storage area with the valve stem pointing toward the rear of the vehicle.

4. Pull the cable (1) through the

door striker (5), the center of the wheel (4), and the plastic spare tire heat shield (3), as shown.

6. Make sure the tire is stored

securely. Push, pull, and then try to turn the tire. If the tire moves, use the wrench to tighten the cable.

1. Cable 2. Liftgate Hinges 3. Spare Tire Heat Shield 4. Center of the Wheel 5. Door Striker

1. Remove the cable package from

the jack storage area.

2. Remove the small center cap by tapping the back of the cap with the extension of the shaft, if the vehicle has aluminum wheels.

5. Hook the cable onto the outside portion of the liftgate hinges (2). 6. Hook the other end of the cable

onto the outside portion of the liftgate hinge on the other side of the vehicle.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (65,1)

7. Pull on the cable to make sure it

is secure.

Storing the Tools

8. Make sure the metal tube is

centered at the striker. Push the tube toward the front of the vehicle.

9. Close the liftgate and make sure

it is latched properly.

1. Tool Bag 2. Wing Bolt 3. Jack

Put back all tools as they were stored in the jack storage compartment and put the compartment cover back on. 1. Ensure that the bottom of the

jack is facing toward you. 2. Replace the tool bag (1).

Vehicle Care

10-65

3. Turn the jack (3) on its side and

place down on the holding bracket.

4. Reinstall the wing bolt (2) by

turning clockwise.

5. To replace the cover, line up the tab at the front of the cover with the notch in the cover opening. Push the cover in place and make sure that the rear clips are in the slots and push the cover closed.

Store the center cap or the plastic bolt-on wheel covers until a full size tire is put back on the vehicle. When you replace the compact spare with a full-size tire, reinstall the bolt-on wheel covers or the center cap. Hand-tighten them over the wheel nuts, using the wrench.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (66,1)

10-66

Vehicle Care

Compact Spare Tire

{ Warning

Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.

If this vehicle has a compact spare tire, it was fully inflated when new; however, it can lose air over time. Check the inflation pressure regularly. It should be 420 kPa (60 psi). Stop as soon as possible and check that the spare tire is correctly inflated after being installed on the vehicle. The compact spare tire is designed for temporary use only. The vehicle will perform differently with the spare tire installed and it is recommended that the vehicle speed be limited to 80 km/h

(50 mph). To conserve the tread of the spare tire, have the standard tire repaired or replaced as soon as convenient and return the spare tire to the storage area. When using a compact spare tire, the ABS and Traction Control systems may engage until the spare tire is recognized by the vehicle, especially on slippery roads. Adjust driving to reduce possible wheel slip. Performance of the All-Wheel Drive (AWD) system will be automatically reduced to protect the system when using the compact spare. To restore the AWD and prevent excessive wear on the clutch in the AWD, replace the compact spare tire with a full-size tire as soon as possible.

{ Caution

When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails which can damage the tire, wheel, and other parts of the vehicle.

Do not use the compact spare on other vehicles. Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together.

{ Caution

Tire chains will not fit the compact spare. Using them can damage the vehicle and the chains. Do not use tire chains on the compact spare.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (67,1)

Jump Starting For more information about the vehicle battery, see Battery on page 10-22. If the vehicle battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.

{ Warning

Batteries can hurt you. They can be dangerous because:

. They contain acid that can

burn you.

. They contain gas that can

explode or ignite.

. They contain enough electricity to burn you.

If you do not follow these steps exactly, some or all of these things can hurt you.

{ Caution

Ignoring these steps could result in costly damage to the vehicle that would not be covered by the vehicle warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle.

1. Check the other vehicle. It must

have a 12-volt battery with a negative ground system.

{ Caution

If the other vehicle does not have a 12-volt system with a negative ground, both vehicles can be damaged. Only use a vehicle that has a 12-volt system with a negative ground for jump starting.

Vehicle Care

10-67

2. Get the vehicles close enough

so the jumper cables can reach, but be sure the vehicles are not touching each other. If they are, it could cause a ground connection you do not want. You would not be able to start your vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake firmly on both vehicles involved in the jump start procedure. Put an automatic transmission in P (Park) or a manual transmission in Neutral before setting the parking brake. If one of the vehicles is a four-wheel-drive vehicle, be sure the transfer case is not in Neutral.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (68,1)

10-68

Vehicle Care

{ Caution

If any accessories are left on or plugged in during the jump starting procedure, they could be damaged. The repairs would not be covered by the vehicle warranty. Whenever possible, turn off or unplug all accessories on either vehicle when jump starting.

3. Turn off the ignition on both

vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlets. Turn off the radio and all lamps that are not needed. This will avoid sparks and help save both batteries. And it could save the radio!

4. Open the hoods and locate the

positive (+) and negative (−) terminal locations on the other vehicle. Your vehicle has a remote positive (+) and a remote negative (−) jump starting terminal. See Engine Compartment Overview on page 10-5 for the terminal locations.

{ Warning

Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.

{ Warning

Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.

5. Check that the jumper cables do

not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative (−) will go to a heavy, unpainted metal engine part or to a remote negative (−) terminal if the vehicle has one.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (69,1)

Vehicle Care

10-69

Do not connect positive (+) to negative (−) or you will get a short that would damage the battery and maybe other parts too. And do not connect the negative (−) cable to the negative (−) terminal on the dead battery because this can cause sparks.

7. Do not let the other end touch

metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.

8. Now connect the black

negative (−) cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative (−) cable does not go to the dead battery. It goes to a heavy, unpainted metal engine part, or to a remote negative (−) terminal on the vehicle with the dead battery.

6. Connect the red positive (+)

cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one.

9. Connect the other end of the

negative (−) cable to the remote negative (−) terminal of the dead battery. Your vehicle has a remote negative (−) terminal for this purpose.

10. Now start the vehicle with the

good battery and run the engine for a while.

11. Try to start the vehicle that had

the dead battery. If it will not start after a few tries, it probably needs service.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (70,1)

10-70

Vehicle Care

{ Caution If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.

Jumper Cable Removal Reverse the sequence exactly when removing the jumper cables.

Towing the Vehicle

{ Caution

Incorrectly towing a disabled vehicle may cause damage. The damage would not be covered by the vehicle warranty.

Have the vehicle towed on a flatbed car carrier or a wheel lift tow truck. If a wheel lift tow truck is used, the drive wheels cannot contact the road while the vehicle is being towed. A wheel dolly must be used to lift all drive wheels off the ground. Consult your dealer or a professional towing service if the disabled vehicle must be towed.

Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motor home. The two most common types

of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground. Dolly towing is towing the vehicle with two wheels on the ground and two wheels up on a device known as a dolly. Here are some important things to consider before recreational vehicle towing:

The towing capacity of the towing vehicle. Be sure to read the tow vehicle manufacturer's recommendations.

. How far the vehicle will be

towed. Some vehicles have restrictions on how far and how long they can be towed. The proper towing equipment. See your dealer or trailering professional for additional advice and equipment recommendations.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (71,1)

If the vehicle is ready to be towed. Just as preparing the vehicle for a long trip, make sure the vehicle is prepared to be towed.

Dinghy Towing

If the vehicle is front-wheel-drive, it can be dinghy towed from the front. These vehicles may also be towed by putting the front wheels on a dolly. See “Dolly Towing” later in this section.

If the vehicle is all-wheel-drive, it can be dinghy towed from the front. These vehicles can also be towed by placing them on a platform trailer with all four wheels off of the ground. These vehicles cannot be towed using a dolly. For vehicles being dinghy towed, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes. This will ensure proper lubrication of transmission components. Reinstall the fuse to start the vehicle. To tow the vehicle from the front with all four wheels on the ground: 1. Position the vehicle to be towed,

shift the transmission to P (Park), and turn the ignition to LOCK/OFF.

2. Secure the vehicle to the towing

vehicle.

3. Set the parking brake. 4. Turn the ignition to ACC/

ACCESSORY.

Vehicle Care

10-71

5. Shift the transmission to

N (Neutral).

6. To prevent the battery from draining while the vehicle is being towed, remove the 15 amp ECM fuse and the 15 amp Onstar fuse. These are in the battery compartment behind the passenger seat on the floor. Also, remove the 50 amp BATT1
fuse from the underhood fuse block and store all fuses in a safe location. See Engine Compartment Fuse Block on page 10-29.

7. Release the parking brake.

{ Caution

If the vehicle is towed without performing each of the steps listed under “Dinghy Towing,” the automatic transmission could be damaged. Be sure to follow all steps of the dinghy towing procedure prior to and after towing the vehicle.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (72,1)

Caution (Continued)

different tire sizes on the front of the vehicle can cause severe damage to the transmission.

a platform trailer with all four wheels off of the ground or dinghy towed from the front. Dolly Towing (Front-Wheel- Drive Vehicles Only)

Dolly Towing (All-Wheel-Drive Vehicles)

10-72

Vehicle Care

{ Caution

If 105 km/h (65 mph) is exceeded while towing the vehicle, it could be damaged. Never exceed 105 km/h (65 mph) while towing the vehicle.

Once the destination is reached: 1. Set the parking brake. 2. Reinstall the fuses. 3. Shift the transmission to

P (Park), turn the ignition to LOCK/OFF and remove the key from the ignition.

4. Disconnect the vehicle from the

towing vehicle.

{ Caution

Do not tow a vehicle with the front drive wheels on the ground if one of the front tires is a compact spare tire. Towing with two

All-wheel-drive vehicles must not be towed with two wheels on the ground. To properly tow these vehicles, they should be placed on

(Continued)

To tow a front-wheel-drive vehicle from the front with two wheels on the ground: 1. Put the front wheels on a dolly. 2. Move the shift lever to P (Park). 3. Set the parking brake.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (73,1)

4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing.

5. Remove the key from the

ignition.

6. Secure the vehicle to the dolly. 7. Release the parking brake. Towing the Vehicle From the Rear

Vehicle Care

10-73

Appearance Care

Exterior Care

Locks Locks are lubricated at the factory. Use a de-icing agent only when absolutely necessary, and have the locks greased after using. See Recommended Fluids and Lubricants on page 11-12. Washing the Vehicle To preserve the vehicle's finish, wash it often and out of direct sunlight.

{ Caution

Do not use petroleum-based, acidic, or abrasive cleaning agents as they can damage the vehicle's paint, metal, or plastic parts. If damage occurs, it would not be covered by the vehicle warranty. Approved cleaning

(Continued)

{ Caution

Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty. Never have the vehicle towed from the rear.

Do not tow the vehicle from the rear.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (74,1)

10-74

Vehicle Care

Caution (Continued)

products can be obtained from your dealer. Follow all manufacturer directions regarding correct product usage, necessary safety precautions, and appropriate disposal of any vehicle care product.

{ Caution Avoid using high-pressure washes closer than 30 cm (12 in) to the surface of the vehicle. Use of power washers exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals.

The e symbol is on any underhood compartment electrical center that should not be power

washed. This could cause damage that would not be covered by the vehicle warranty. If using an automatic car wash, follow the car wash instructions. The windshield wiper and rear window wiper, if equipped, must be off. Remove any accessories that may be damaged or interfere with the car wash equipment. Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. Finish Care Application of aftermarket clearcoat sealant/wax materials is not recommended. If painted surfaces are damaged, see your dealer to have the damage assessed and repaired. Foreign materials such as

calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Occasional hand waxing or mild polishing should be done to remove residue from the paint finish. See your dealer for approved cleaning products. Do not apply waxes or polishes to uncoated plastic, vinyl, rubber, decals, simulated wood, or flat paint as damage can occur.

{ Caution Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish

(Continued)

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (75,1)

Caution (Continued)

may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle.

To keep the paint finish looking new, keep the vehicle garaged or covered whenever possible.

Protecting Exterior Bright Metal Moldings

{ Caution

Failure to clean and protect the bright metal moldings can result in a hazy white finish or pitting. This damage would not be covered by the vehicle warranty.

The bright metal moldings on the vehicle are aluminum or stainless steel. To prevent damage always follow these cleaning instructions: . Be sure the molding is cool to the touch before applying any cleaning solution.

. Use a cleaning solution

approved for aluminum or stainless steel. Some cleaners are highly acidic or contain alkaline substances and can damage the moldings.

. Always dilute a concentrated

cleaner according to the manufacturer’s instructions. . Do not use chrome cleaners. . Do not use cleaners that are not

intended for automotive use.

. Use a nonabrasive wax on the vehicle after washing to protect and extend the molding finish.

Vehicle Care

10-75

Cleaning Exterior Lamps/ Lenses, Emblems, Decals and Stripes Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps, lenses, emblems, decals and stripes. Follow instructions under "Washing the Vehicle" previously in this section. Lamp covers are made of plastic, and some have a UV protective coating. Do not clean or wipe them when dry. Do not use any of the following on lamp covers: . Abrasive or caustic agents. . Washer fluids and other cleaning

agents in higher concentrations than suggested by the manufacturer.

. Solvents, alcohols, fuels, or other harsh cleaners. Ice scrapers or other hard items.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (76,1)

10-76

Vehicle Care

. Aftermarket appearance caps or

covers while the lamps are illuminated, due to excessive heat generated.

{ Caution

Failure to clean lamps properly can cause damage to the lamp cover that would not be covered by the vehicle warranty.

{ Caution

Using wax on low gloss black finish stripes can increase the gloss level and create a non-uniform finish. Clean low gloss stripes with soap and water only.

Air Intakes Clear debris from the air intakes, between the hood and windshield when washing the vehicle.

Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean rubber blades using a lint-free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking. Replace the wiper blades if they are worn or damaged. Damage can be caused by extreme dusty conditions, sand, salt, heat, sun, snow, and ice. Weatherstrips Apply Dielectric silicone grease on weatherstrips to make them last longer, seal better, and not stick or squeak. Lubricate weatherstrips at least once a year. Hot, dry climates may require more frequent application. Black marks from rubber material on painted surfaces

can be removed by rubbing with a clean cloth. See Recommended Fluids and Lubricants on page 11-12. Tires Use a stiff brush with tire cleaner to clean the tires.

{ Caution

Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/ or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.

Wheels and Trim — Aluminum or Chrome Use a soft, clean cloth with mild soap and water to clean the wheels. After rinsing thoroughly with clean water, dry with a soft, clean towel. A wax may then be applied.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (77,1)

{ Caution

Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium, or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash the chrome with soap and water after exposure.

{ Caution

To avoid surface damage, do not use strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels. Use only approved cleaners. Also, never drive a vehicle with aluminum or chrome-plated wheels through an (Continued)

Caution (Continued)

automatic car wash that uses silicone carbide tire cleaning brushes. Damage could occur and the repairs would not be covered by the vehicle warranty.

Steering, Suspension, and Chassis Components Visually inspect steering, suspension, and chassis components for damaged, loose, or missing parts or signs of wear at least once a year. Inspect power steering for proper hook-up, binding, leaks, cracks, chafing, etc. Visually check constant velocity joint boots and axle seals for leaks. Body Component Lubrication Lubricate all key lock cylinders, hood hinges, liftgate hinges, steel fuel door hinge, unless the components are plastic. Applying

Vehicle Care

10-77

silicone grease on weatherstrips with a clean cloth will make them last longer, seal better, and not stick or squeak. Underbody Maintenance At least twice a year, spring and fall use plain water to flush any corrosive materials from the underbody. Take care to thoroughly clean any areas where mud and other debris can collect. Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (78,1)

10-78

Vehicle Care

Finish Damage Quickly repair minor chips and scratches with touch-up materials available from your dealer to avoid corrosion. Larger areas of finish damage can be corrected in your dealer's body and paint shop. Chemical Paint Spotting Airborne pollutants can fall upon and attack painted vehicle surfaces causing blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. See “Finish Care” previously in this section.

Interior Care To prevent dirt particle abrasions, regularly clean the vehicle's interior. Immediately remove any soils. Note that newspapers or dark garments that can transfer color to home furnishings can also permanently transfer color to the vehicle's interior.

Use a soft bristle brush to remove dust from knobs and crevices on the instrument cluster. Using a mild soap solution, immediately remove hand lotions, sunscreen, and insect repellent from all interior surfaces or permanent damage may result. Your dealer may have products for cleaning the interior. Use cleaners specifically designed for the surfaces being cleaned to prevent permanent damage. Apply all cleaners directly to the cleaning cloth. Do not spray cleaners directly on any switches or controls. Cleaners should be removed quickly. Never allow cleaners to remain on the surface being cleaned for extended periods of time. Cleaners may contain solvents that can become concentrated in the interior. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning the interior, maintain adequate ventilation by opening the doors and windows.

To prevent damage, do not clean the interior using the following cleaners or techniques: . Never use a razor or any other

sharp object to remove a soil from any interior surface.

. Never use a brush with stiff

bristles.

. Never rub any surface

aggressively or with excessive pressure.

. Do not use laundry detergents or

dishwashing soaps with degreasers. For liquid cleaners, use approximately 20 drops per 3.8 L (1 gal) of water. A concentrated soap solution will leave a residue that creates streaks and attracts dirt. Do not use solutions that contain strong or caustic soap.

. Do not heavily saturate the upholstery when cleaning.

. Do not use solvents or cleaners

containing solvents.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (79,1)

Interior Glass To clean, use a terry cloth fabric dampened with water. Wipe droplets left behind with a clean dry cloth. Commercial glass cleaners may be used, if necessary, after cleaning the interior glass with plain water.

{ Caution

To prevent scratching, never use abrasive cleaners on automotive glass. Abrasive cleaners or aggressive cleaning may damage the rear window defogger.

Cleaning the windshield with water during the first three to six months of ownership will reduce tendency to fog. Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap.

Coated Moldings Coated moldings should be cleaned. . When lightly soiled, wipe with a

sponge or soft lint-free cloth dampened with water.

. When heavily soiled, use warm

soapy water.

Fabric/Carpet/Suede Start by vacuuming the surface using a soft brush attachment. If a rotating brush attachment is being used during vacuuming, only use it on the floor carpet. Before cleaning, gently remove as much of the soil as possible using one of the following techniques: . Gently blot liquids with a paper towel. Continue blotting until no more soil can be removed. For solid soils, remove as much as possible prior to vacuuming.

Vehicle Care

10-79

To clean: 1. Saturate a clean lint-free colorfast cloth with water. Microfiber cloth is recommended to prevent lint transfer to the fabric or carpet.

2. Remove excess moisture by

gently wringing until water does not drip from the cleaning cloth. 3. Start on the outside edge of the

soil and gently rub toward the center. Fold the cleaning cloth to a clean area frequently to prevent forcing the soil in to the fabric.

4. Continue gently rubbing the soiled area until there is no longer any color transfer from the soil to the cleaning cloth. If the soil is not completely removed, use a mild soap solution followed only by plain water.

5.

If the soil is not completely removed, it may be necessary to use a commercial upholstery

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (80,1)

10-80

Vehicle Care

cleaner or spot lifter. Test a small hidden area for colorfastness before using a commercial upholstery cleaner or spot lifter. If ring formation occurs, clean the entire fabric or carpet. Following the cleaning process, a paper towel can be used to blot excess moisture. Cleaning High Gloss Surfaces and Vehicle Information and Radio Displays For vehicles with high gloss surfaces or vehicle displays, use a microfiber cloth to wipe surfaces. Before wiping the surface with the microfiber cloth, use a soft bristle brush to remove dirt that could scratch the surface. Then use the microfiber cloth by gently rubbing to clean. Never use window cleaners or solvents. Periodically hand wash the microfiber cloth separately, using mild soap. Do not use bleach or fabric softener. Rinse thoroughly and air dry before next use.

{ Caution

{ Caution

Do not attach a device with a suction cup to the display. This may cause damage and would not be covered by the vehicle warranty.

Instrument Panel, Leather, Vinyl, Other Plastic Surfaces, Low Gloss Paint Surfaces and Natural Open Pore Wood Surfaces Use a soft microfiber cloth dampened with water to remove dust and loose dirt. For a more thorough cleaning, use a soft microfiber cloth dampened with a mild soap solution.

Soaking or saturating leather, especially perforated leather, as well as other interior surfaces, may cause permanent damage. Wipe excess moisture from these surfaces after cleaning and allow them to dry naturally. Never use heat, steam, or spot removers. Do not use cleaners that contain silicone or wax-based products. Cleaners containing these solvents can permanently change the appearance and feel of leather or soft trim, and are not recommended.

Do not use cleaners that increase gloss, especially on the instrument panel. Reflected glare can decrease visibility through the windshield under certain conditions.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (81,1)

{ Caution

{ Warning

Use the following guidelines for proper floor mat usage.

Vehicle Care

10-81

Use of air fresheners may cause permanent damage to plastics and painted surfaces. If an air freshener comes in contact with any plastic or painted surface in the vehicle, blot immediately and clean with a soft cloth dampened with a mild soap solution. Damage caused by air fresheners would not be covered by the vehicle warranty.

Cargo Cover and Convenience Net Wash with warm water and mild detergent. Do not use chlorine bleach. Rinse with cold water, and then dry completely. Care of Safety Belts Keep belts clean and dry.

Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.

Floor Mats

{ Warning

If a floor mat is the wrong size or is not properly installed, it can interfere with the pedals. Interference with the pedals can cause unintended acceleration and/or increased stopping distance which can cause a crash and injury. Make sure the floor mat does not interfere with the pedals.

The original equipment floor mats were designed for your vehicle. If the floor mats need replacing, it is recommended that GM certified floor mats be purchased. Non-GM floor mats may not fit properly and may interfere with the accelerator or brake pedal. Always check that the floor mats do not interfere with the pedals.

. Do not use a floor mat if the

vehicle is not equipped with a floor mat retainer on the driver side floor.

. Use the floor mat with the

correct side up. Do not turn it over.

. Do not place anything on top of

the driver side floor mat.

. Use only a single floor mat on

the driver side.

. Do not place one floor mat on

top of another.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (82,1)

10-82

Vehicle Care

Button Retainer Some vehicles have floor mats with a button-type retainer.

3. Make sure the floor mat is

properly secured and verify that it does not interfere with the pedals.

Knob Retainer Some vehicles have floor mats with a knob retainer.

3. Center the slot in the floor mat grommet with the knob on the floor and set into position.

4. Turn the knob until it is

perpendicular to the slot in the grommet to lock the mat in place.

5. Make sure the floor mat is

properly secured and verify that it does not interfere with the pedals.

Removing and Replacing the Floor Mat 1. Pull up on the rear of the mat to

unlock and remove.

2. Reinstall the floor mat by lining up the floor mat openings over the carpet retainers and snapping into position.

Removing and Replacing the Floor Mat 1. Turn the knob until it is aligned

with the slot in the floor mat grommet.

2. Pull up on the floor mat.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (1,1)

Service and Maintenance

General Information

General Information . . . . . . . . . . 11-1

Maintenance Schedule

Maintenance Schedule . . . . . . . 11-2

Special Application Services

Special Application

Services . . . . . . . . . . . . . . . . . . . . 11-8

Additional Maintenance and Care

Additional Maintenance

and Care . . . . . . . . . . . . . . . . . . . 11-8

Recommended Fluids, Lubricants, and Parts

Recommended Fluids and

Lubricants . . . . . . . . . . . . . . . . . 11-12

Maintenance Replacement

Parts . . . . . . . . . . . . . . . . . . . . . . 11-13

Maintenance Records

Maintenance Records . . . . . . 11-14

Service and Maintenance

11-1

General Information Your vehicle is an important investment. This section describes the required maintenance for the vehicle. Follow this schedule to help protect against major repair expenses resulting from neglect or inadequate maintenance. It may also help to maintain the value of the vehicle if it is sold. It is the responsibility of the owner to have all required maintenance performed. Your dealer has trained technicians who can perform required maintenance using genuine replacement parts. They have up-to-date tools and equipment for fast and accurate diagnostics. Many dealers have extended evening and Saturday hours, courtesy transportation, and online scheduling to assist with service needs. Your dealer recognizes the importance of providing competitively priced maintenance and repair services. With trained

technicians, the dealer is the place for routine maintenance such as oil changes and tire rotations and additional maintenance items like tires, brakes, batteries, and wiper blades.

{ Caution

Damage caused by improper maintenance can lead to costly repairs and may not be covered by the vehicle warranty. Maintenance intervals, checks, inspections, recommended fluids, and lubricants are important to keep the vehicle in good working condition.

The Tire Rotation and Required Services are the responsibility of the vehicle owner. It is recommended to have your dealer perform these services every 12 000 km/7,500 mi. Proper vehicle maintenance helps to keep the vehicle in good working condition, improves fuel economy, and reduces vehicle emissions.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (2,1)

11-2

Service and Maintenance

Frequently towing a trailer.

. Used for high speed or

competitive driving.

. Used for taxi, police, or delivery

service.

Refer to the information in the Maintenance Schedule Additional Required Services - Severe chart.

{ Warning

Performing maintenance work can be dangerous and can cause serious injury. Perform maintenance work only if the required information, proper tools, and equipment are available. If they are not, see your dealer to have a trained technician do the work. See Doing Your Own Service Work on page 10-3.

Maintenance Schedule

Owner Checks and Services

At Each Fuel Stop . Check the engine oil level. See

Engine Oil on page 10-7.

Once a Month . Check the tire inflation

pressures. See Tire Pressure on page 10-43. Inspect the tires for wear. See Tire Inspection on page 10-48.

. Check the windshield washer

fluid level. See Washer Fluid on page 10-19.

Because of the way people use vehicles, maintenance needs vary. There may need to be more frequent checks and services. The Additional Required Services - Normal are for vehicles that: . Carry passengers and cargo within recommended limits on the Tire and Loading Information label. See Vehicle Load Limits on page 9-9.

. Are driven on reasonable road

surfaces within legal driving limits.

. Use the recommended fuel. See

Fuel on page 9-43.

Refer to the information in the Maintenance Schedule Additional Required Services - Normal chart. The Additional Required Services - Severe are for vehicles that are: . Mainly driven in heavy city traffic

in hot weather.

. Mainly driven in hilly or

mountainous terrain.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (3,1)

Service and Maintenance

11-3

Engine Oil Change When the CHANGE ENGINE OIL SOON message displays, have the engine oil and filter changed within the next 1 000 km/600 mi. If driven under the best conditions, the engine oil life system may not indicate the need for vehicle service for up to a year. The engine oil and filter must be changed at least once a year and the oil life system must be reset. Your trained dealer technician can perform this work. If the engine oil life system is reset accidentally, service the vehicle within 5 000 km/ 3,000 mi since the last service. Reset the oil life system when the oil is changed. See Engine Oil Life System on page 10-9.

Tire Rotation and Required Services Every 12 000 km/ 7,500 mi Rotate the tires, if recommended for the vehicle, and perform the following services. See Tire Rotation on page 10-49. . Check engine oil level and oil

life percentage. If needed, change engine oil and filter, and reset oil life system. See Engine Oil on page 10-7 and Engine Oil Life System on page 10-9.

. Check engine coolant level. See Engine Coolant on page 10-12. . Check windshield washer fluid

level. See Washer Fluid on page 10-19.

. Visually inspect windshield wiper

blades for wear, cracking, or contamination. See Exterior Care on page 10-73. Replace worn or damaged wiper blades. See Wiper Blade Replacement on page 10-24.

. Check tire inflation pressures.

See Tire Pressure on page 10-43. Inspect tire wear. See Tire Inspection on page 10-48.

. Visually check for fluid leaks.

Inspect engine air cleaner filter. See Engine Air Cleaner/Filter on page 10-11. Inspect brake system.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (4,1)

11-4

Service and Maintenance

. Visually inspect steering, suspension, and chassis components for damaged, loose, or missing parts or signs of wear. See Exterior Care on page 10-73.

. Check restraint system

components. See Safety System Check on page 3-21.

. Visually inspect fuel system for

damage or leaks.

. Visually inspect exhaust system

and nearby heat shields for loose or damaged parts. Lubricate body components. See Exterior Care on page 10-73.

. Check starter switch. See Starter

. Check accelerator pedal for

Switch Check on page 10-23. . Check automatic transmission shift lock control function. See Automatic Transmission Shift Lock Control Function Check on page 10-23.

. Check ignition transmission lock.

See Ignition Transmission Lock Check on page 10-24.

. Check parking brake and

automatic transmission park mechanism. See Park Brake and P (Park) Mechanism Check on page 10-24.

damage, high effort, or binding. Replace if needed.

. Visually inspect gas strut for

signs of wear, cracks, or other damage. Check the hold open ability of the strut. See your dealer if service is required. Inspect sunroof track and seal, if equipped. See Sunroof on page 2-19.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (5,1)

Service and Maintenance

11-5

Maintenance Schedule Additional Required Services - Normal

Rotate tires and perform Required Services. Check engine oil level and oil life percentage. Change engine oil and filter, if needed.