2015 Chevrolet Traverse Owners Manual

{ Caution

Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords.

Power Outlet 120 Volt Alternating Current If equipped with this power outlet it can be used to plug in electrical equipment that uses a maximum limit of 150 watts.

The power outlet is on the rear of the center console. An indicator light on the outlet turns on to show it is in use. The light comes on when the ignition is in

ON/RUN, equipment requiring less than 150 watts is plugged into the outlet, and no system fault is detected. The indicator light does not come on when the ignition is in LOCK/OFF or if the equipment is not fully seated into the outlet. If equipment is connected using more than 150 watts or a system fault is detected, a protection circuit shuts off the power supply and the indicator light turns off. To reset the circuit, unplug the item and plug it back in or turn the Retained Accessory Power (RAP) off and then back on. See Retained Accessory Power (RAP) on page 9-19. The power restarts when equipment using 150 watts or less is plugged into the outlet and a system fault is not detected.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (11,1)

Instruments and Controls

5-11

The power outlet is not designed for and may not work properly, if the following are plugged in: . Equipment with high initial peak

wattage such as: compressor-driven refrigerators and electric power tools.

. Other equipment requiring an extremely stable power supply such as: microcomputer-controlled electric blankets, touch sensor lamps, etc.

. Medical equipment. See High Voltage Devices and Wiring on page 10-28.

Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Warning lights come on when there could be a problem with a vehicle function. Some warning lights come on briefly when the engine is started to indicate they are working.

Gauges can indicate when there could be a problem with a vehicle function. Often gauges and warning lights work together to indicate a problem with the vehicle. When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Waiting to do repairs can be costly and even dangerous.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (12,1)

5-12

Instruments and Controls

Instrument Cluster

English Uplevel Shown, Metric Similar

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (13,1)

Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph).

Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles.

Tachometer The tachometer displays the engine speed in revolutions per minute (rpm).

{ Caution

If the engine is operated with the rpm’s in the warning area at the high end of the tachometer, the vehicle could be damaged, and the damage would not be covered by the vehicle warranty. Do not operate the engine with the rpm’s in the warning area.

Fuel Gauge

Metric

English

Instruments and Controls

5-13

When the ignition is on, the fuel gauge shows how much fuel is left in the tank. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. The gauge will first indicate empty before the vehicle is out of fuel, but the vehicle's fuel tank should be filled soon. When the fuel tank is low on fuel, the FUEL LEVEL LOW message will appear on the Driver Information Center (DIC). For more information see Fuel System Messages on page 5-38. Here are some situations that may occur with the fuel gauge. None of these indicate a problem with the fuel gauge. . At the gas station, the gas pump

shuts off before the gauge reads full.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (14,1)

5-14

Instruments and Controls

It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge might have indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. The gauge moves a little while turning a corner or speeding up. The gauge does not go back to empty when the ignition is turned off.

Engine Coolant Temperature Gauge

Metric

English

This gauge shows the engine coolant temperature. If the gauge pointer moves into the red area, it means that the engine coolant has overheated. If the vehicle has been operated under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible. See Engine Overheating on page 10-16 for more information.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (15,1)

Voltmeter Gauge

When the engine is not running, but the ignition is on, this gauge displays the battery voltage in DC volts. When the engine is running, this gauge shows the condition of the charging system. The vehicle's charging system regulates voltage based on the state of charge of the battery. The voltmeter may fluctuate. This is normal. Readings between the low and high warning zones indicate the normal operating range.

Instruments and Controls

5-15

Readings in the low warning zone can occur when a large number of electrical accessories are operating in the vehicle and the engine is left idling for an extended period. If there is a problem with the battery charging system, a SERVICE BATTERY CHARGING SYSTEM message will appear in the Driver Information Center (DIC) and/or the charging system light comes on. See Battery Voltage and Charging Messages on page 5-34 for more information. However, readings in either warning zone may indicate a possible problem in the electrical system. Have the vehicle serviced as soon as possible.

Safety Belt Reminders

Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.

When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on. Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System on page 3-29.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (16,1)

5-16

Instruments and Controls

Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 3-22.

The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.

{ Warning

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

If there is a problem with the airbag system, a Driver Information Center (DIC) message may also come on. See Airbag System Messages on page 5-41.

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3-29 for

When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on. The front passenger safety belt reminder light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop, or other electronic device. To turn off the reminder light and/or chime, remove the object from the seat or buckle the safety belt.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (17,1)

Instruments and Controls

5-17

important safety information. The instrument panel has a passenger airbag status indicator.

United States

Canada and Mexico

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the front outboard passenger frontal airbag.

If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the front outboard passenger frontal airbag is allowed to inflate. If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ Warning

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right

(Continued)

Warning (Continued)

away. See Airbag Readiness Light on page 5-16 for more information, including important safety information.

Charging System Light

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started. If the light stays on, or comes on while driving, there may be a problem with the electrical charging

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (18,1)

5-18

Instruments and Controls

system. Have it checked by your dealer. Driving while this light is on could drain the battery. When this light comes on, the Driver Information Center (DIC) also displays the SERVICE BATTERY CHARGING SYSTEM message. See Vehicle Messages on page 5-34 for more information. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions are at acceptable levels, helping to maintain a clean environment. The malfunction indicator lamp comes on when the vehicle is placed in ON/RUN, as a check to show it is

working. If it does not, have the vehicle serviced by your dealer. See Ignition Positions on page 9-14.

If the malfunction indicator lamp comes on while the engine is running, this indicates that the OBD II system has detected a problem and diagnosis and service might be required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system also assists the service technician in correctly diagnosing any malfunction.

{ Caution

If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.

{ Caution

Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems

(Continued)

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (19,1)

Caution (Continued)

could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 10-2.

This light may come on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades.

Instruments and Controls

5-19

If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.

If the light continues to flash, find a safe place to stop and park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emission control system malfunction: . Check that the fuel cap is fully

installed. See Filling the Tank on page 9-44. The diagnostic system may be able to determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap could allow fuel to evaporate

into the atmosphere. A few driving trips with the cap properly installed may turn the light off.

. Check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If this occurs, change the fuel brand used. It may require at least one full tank of the proper fuel to turn the light off.

See Fuel on page 9-43. If the light remains on, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (20,1)

5-20

Instruments and Controls

Emissions Inspection and Maintenance Programs Depending on where you live, your vehicle may be required to participate in an emission control system inspection and maintenance program. For the inspection, the emission system test equipment will likely connect to the vehicle's Data Link Connector (DLC).

the ignition is turned to ON/RUN while the engine is off. See your dealer for assistance in verifying proper operation of the malfunction indicator lamp. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed. The vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

The DLC is under the instrument panel to the left of the steering wheel. See your dealer if assistance is needed. The vehicle may not pass inspection if:

The malfunction indicator lamp is on with the engine running, or if the light does not come on when

The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.

Metric

English

This light should come on briefly when the ignition key is turned to ON/RUN. If it does not come on then, have it fixed so it will be ready to warn if there is a problem.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (21,1)

This light may also come on due to low brake fluid. See Brake Fluid on page 10-21. When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light will stay on if the parking brake does not release fully. If it stays on after the parking brake is fully released, it means there is a brake problem. If the light comes on while driving, pull off the road and stop carefully. Make sure the parking brake is fully released. The pedal may be harder to push or, the pedal may go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle on page 10-70.

Instruments and Controls

5-21

{ Warning

Antilock Brake System (ABS) Warning Light

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

The brake message remains on until any DIC button is pressed. The brake light remains on until the problem is fixed. See Brake System Messages on page 5-35.

The ABS warning light comes on briefly when the ignition key is turned to ON/RUN. This is normal. If the light does not come on then, have it fixed so it will be ready to warn you if there is a problem. If the light stays on, turn the ignition to LOCK/OFF. If the light comes on while driving, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the light still stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (22,1)

5-22

Instruments and Controls

on, there are still brakes, but no antilock brakes. If the regular brake system warning light is also on, there are no antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5-20.

Tow/Haul Mode Light

This light comes on when the Tow/ Haul mode has been activated. For more information, see Tow/Haul Mode on page 9-25.

Lane Departure Warning (LDW) Light

Vehicle Ahead Indicator

If equipped, this indicator will display green when a vehicle is detected ahead and amber when you are following a vehicle ahead much too closely. See Forward Collision Alert (FCA) System on page 9-33.

If equipped, this light comes on briefly while starting the vehicle. If it does not come on, have the vehicle serviced. This light is green if LDW is on and ready to operate. This light changes to amber and flashes to indicate that the lane marking has been crossed without using a turn signal in that direction. See Lane Departure Warning (LDW) on page 9-41.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (23,1)

StabiliTrak® Indicator Light

Engine Coolant Temperature Warning Light

Instruments and Controls

5-23

Tire Pressure Light

The StabiliTrak light comes on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. This light flashes while the StabiliTrak system or the Traction Control System (TCS) is working. The light comes on when there is a problem with the StabiliTrak system. See Traction Control/Electronic Stability Control on page 9-28.

The engine coolant temperature warning light comes on briefly when the vehicle is started. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then goes off. If the light comes on and stays on while driving, the vehicle may have a problem with the cooling system. Stop and turn off the vehicle to avoid damage to the engine. A warning chime sounds when this light is on. See Engine Overheating on page 10-16 for more information.

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages on page 5-42. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10-43.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (24,1)

5-24

Instruments and Controls

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10-45.

Engine Oil Pressure Light

low can also damage the

{ Caution Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

This light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Security Light

The security light should come on briefly as the engine is started. If the system is working normally, the indicator light turns off. If it does not come on, have the vehicle serviced by your dealer. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. This light is also used to indicate the status of the anti-theft alarm system when the ignition is turned off. The light will flash rapidly if the alarm system is arming and one or more of the monitored entry points is not closed. The light will stay on if the alarm is arming and all entry points are closed.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (25,1)

For information regarding this light and the vehicle's security system, see Vehicle Alarm System on page 2-12.

High-Beam On Light

This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6-2 for more information.

Instruments and Controls

5-25

Cruise Control Light

Information Displays

This light comes on when the cruise control is set. This light goes out when the cruise control is canceled. See Cruise Control on page 9-30.

Driver Information Center (DIC) (With DIC Buttons) If your vehicle has DIC buttons, the information below explains the operation of this system. The DIC displays information about your vehicle. It also displays warning messages if a system problem is detected. All messages will appear in the DIC display at the top of the instrument cluster. The DIC comes on when the ignition is on. After a short delay, the DIC will display the information that was last displayed before the engine was turned off. The DIC also displays a shift lever position indicator on the bottom line of the display. See Automatic Transmission on page 9-22.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (26,1)

5-26

Instruments and Controls

The outside air temperature and compass, if equipped, also display on the DIC when viewing the trip and fuel information. The outside air temperature automatically appears in the top right corner of the DIC display. If there is a problem with the system that controls the temperature display, the numbers will be replaced with dashes. If this occurs, have the vehicle serviced. The compass will be shown in the bottom right corner of the DIC display. See Compass on page 5-6. The DIC also allows some features to be customized. See Vehicle Personalization (With DIC Buttons) on page 5-45. If your vehicle has DIC buttons, you can also use the trip odometer reset stem to view the odometer and trip odometers.

DIC Buttons The DIC has different displays, which can be accessed by pressing the DIC buttons on the center stack.

The buttons are the set/reset, customization, vehicle information, and trip/fuel buttons. The button functions are detailed in the following pages. V (Set/Reset): Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC. U (Customization): Press this button to customize the feature settings on your vehicle. See Vehicle Personalization (With DIC Buttons) on page 5-45. T (Vehicle Information): Press this button to display the oil life, park assist on vehicles with this feature, units, tire pressure readings on vehicles with this feature, and compass calibration and zone setting on vehicles with this feature.

3 (Trip/Fuel): Press this button to display the odometer, trip odometers, fuel range, average economy, timer, fuel used, and average speed. Vehicle Information Menu Items T (Vehicle Information): Press this button to scroll through the following menu items:

OIL LIFE Press the vehicle information button until OIL LIFE REMAINING displays. This display shows an estimate of the oil's remaining useful life. If you see 99% OIL LIFE REMAINING on the display, that means 99% of the current oil life remains. The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (27,1)

Instruments and Controls

5-27

When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5-37. You should change the oil as soon as you can. See Engine Oil on page 10-7. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule. See Maintenance Schedule on page 11-2. Remember, you must reset the OIL LIFE display yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, see Engine Oil Life System on page 10-9.

SIDE BLIND ZONE ALERT If the vehicle has the Side Blind Zone Alert (SBZA) system, this display allows the system to be turned on or off. Once in this display, press the set/reset button to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off. When the SBZA system is turned off, the DIC will display the SIDE BLIND ZONE ALERT SYSTEM OFF message as a reminder that the system has been turned off. See Object Detection System Messages on page 5-39 and Side Blind Zone Alert (SBZA) on page 9-36.

PARK ASSIST If your vehicle has the Rear Parking Assist (RPA) system, press the vehicle information button until PARK ASSIST displays. This display allows the system to be turned on or off. Once in this display, press the set/reset button to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off. The RPA system automatically turns back on after each vehicle start. When the RPA system is turned off and the vehicle is shifted out of P (Park), the DIC will display the PARK ASSIST OFF message as a reminder that the system has been turned off. See Object Detection System Messages on page 5-39 and Parking Assist on page 9-35.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (28,1)

5-28

Instruments and Controls

REAR CROSS TRAFFIC ALERT If the vehicle has the Rear Cross Traffic Alert (RCTA) system, this display allows the system to be turned on or off. Once in this display, press the set/reset button to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off. When the RCTA system is turned off, the DIC will display the REAR CROSS TRAFFIC ALERT SYSTEM OFF message as a reminder that the system has been turned off. See Object Detection System Messages on page 5-39 and Rear Vision Camera (RVC) on page 9-38.

UNITS Press the vehicle information button until UNITS displays. This display allows you to select between metric or English units of measurement. Once in this display, press the set/ reset button to select between METRIC or ENGLISH units. All of

the vehicle information will then be displayed in the unit of measurement selected.

FRONT TIRES or REAR TIRES On vehicles with the Tire Pressure Monitor System (TPMS), the pressure for each tire can be viewed in the DIC. The tire pressure will be shown in either kilopascals (kPa) or pounds per square inch (psi). Press the vehicle information button until the DIC displays FRONT TIRES kPa (PSI) LEFT ## RIGHT ##. Press the vehicle information button again until the DIC displays REAR TIRES kPa (PSI) LEFT ## RIGHT ##. If a low tire pressure condition is detected by the system while driving, a message advising you to add air to a specific tire will appear in the display. See Tire Pressure on page 10-43 and Tire Messages on page 5-42.

If the tire pressure display shows dashes instead of a value, there may be a problem with your vehicle. If this consistently occurs, see your dealer for service.

COMPASS ZONE SETTING This display will be available if the vehicle has a compass. See Compass on page 5-6.

COMPASS RECALIBRATION This display will be available if the vehicle has a compass. See Compass on page 5-6.

Blank Display This display shows no information. Trip/Fuel Menu Items 3 (Trip/Fuel): Press this button to scroll through the following menu items:

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (29,1)

ODOMETER Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either kilometers (km) or miles (mi). Pressing the trip odometer reset stem will also display the odometer. To switch between English and metric measurements, see “UNITS” earlier in this section.

TRIP A and TRIP B Press the trip/fuel button until TRIP A or TRIP B displays. This display shows the current distance traveled in either kilometers (km) or miles (mi) since the last reset for each trip odometer. Both trip odometers can be used at the same time. Pressing the trip odometer reset stem will also display the trip odometers.

Instruments and Controls

5-29

Each trip odometer can be reset to zero separately by pressing the set/ reset button or the trip odometer reset stem while the desired trip odometer is displayed. The trip odometer has a feature called retroactive reset. This can be used to set the trip odometer to the number of kilometers (miles) driven since the ignition was last turned on. This can be used if the trip odometer is not reset at the beginning of the trip. To use the retroactive reset feature, press and hold the set/reset button for at least four seconds. The trip odometer will display the number of kilometers (km) or miles (mi) driven since the ignition was last turned on and the vehicle was moving. Once the vehicle begins moving, the trip odometer will accumulate mileage. For example, if the vehicle was driven 8 km (5 mi) before it is started again, and then the retroactive reset feature is activated, the display will show 8 km (5 mi). As the vehicle

begins moving, the display will then increase to 8.2 km (5.1 mi), 8.4 km (5.2 mi), etc. If the retroactive reset feature is activated after the vehicle is started, but before it begins moving, the display will show the number of kilometers (km) or miles (mi) driven during the last ignition cycle.

RANGE Press the trip/fuel button until RANGE displays. This display shows the approximate number of remaining kilometers (km) or miles (mi) the vehicle can be driven without refueling. The display will show LOW if the fuel level is low. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This estimate will change if driving conditions change. For example, if driving in traffic and making frequent stops, this display may read one number, but if the vehicle is driven on a freeway, the

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (30,1)

5-30

Instruments and Controls

number may change even though the same amount of fuel is in the fuel tank. This is because different driving conditions produce different fuel economies. Generally, freeway driving produces better fuel economy than city driving. Fuel range cannot be reset.

AVG (Average) ECONOMY Press the trip/fuel button until AVG ECONOMY displays. This display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the approximate average fuel economy that the vehicle has right now, and will change as driving conditions change. This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. To reset AVG ECONOMY, press and hold the set/reset button.

FUEL ECONOMY Press the trip/fuel button until FUEL ECONOMY displays. The FUEL ECONOMY display shows an approximate estimate of the vehicle fuel economy under a given driving condition at a specific moment. For example, if the vehicle is accelerating and achieving low fuel efficiency this display will show fewer bars, but if the vehicle is cruising on a flat freeway and getting high fuel efficiency, the display will show more bars. Fuel economy cannot be reset.

TIMER Press the trip/fuel button until TIMER displays. This display can be used as a timer. To start the timer, press the set/ reset button while TIMER is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if

another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press the set/reset button briefly while TIMER is displayed. To reset the timer to zero, press and hold the set/reset button while TIMER is displayed.

FUEL USED Press the trip/fuel button until FUEL USED displays. This display shows the number of liters (L) or gallons (gal) of fuel used since the last reset of this menu item. To reset the fuel used information, press and hold the set/reset button while FUEL USED is displayed.

AVG (Average) SPEED Press the trip/fuel button until AVG SPEED displays. This display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph).

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (31,1)

Instruments and Controls

5-31

This average is calculated based on the various vehicle speeds recorded since the last reset of this value. To reset the value to zero, press and hold the set/reset button.

Blank Display This display shows no information.

Driver Information Center (DIC) (Without DIC Buttons) If your vehicle does not have DIC buttons, the information below explains the operation of this system. The DIC has different displays, which can be accessed by pressing the trip odometer reset stem on the instrument cluster. Pressing the trip odometer reset stem will also turn off, or acknowledge, DIC messages. The DIC displays trip and vehicle system information, and warning messages if a system problem is detected.

If your vehicle does not have DIC buttons, you can use the trip odometer reset stem to view the following displays: odometer, trip odometers, oil life, park assist menu for vehicles with the Rear Parking Assist (RPA) system, units, and display language. If your vehicle has DIC buttons, you can use the trip odometer reset stem to view the following displays: odometer and trip odometers. Trip Odometer Reset Stem Menu Items

ODOMETER Press the trip odometer reset stem until ODOMETER displays. This display shows the distance the vehicle has been driven in either kilometers (km) or miles (mi). To switch between English and metric measurements, see “UNITS” later in this section.

TRIP A or TRIP B Press the trip odometer reset stem until TRIP A or TRIP B displays. This display shows the current distance traveled in either kilometers (km) or miles (mi) since the last reset for each trip odometer. Both trip odometers can be used at the same time. Each trip odometer can be reset to zero separately by pressing and holding the trip odometer reset stem while the desired trip odometer is displayed. The trip odometer has a feature called the retroactive reset. This can be used to set the trip odometer to the number of kilometers (miles) driven since the ignition was last turned on. This can be used if the trip odometer is not reset at the beginning of the trip. To use the retroactive reset feature, press and hold the trip odometer reset stem for at least four seconds. The trip odometer will display the number of kilometers (km) or

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (32,1)

5-32

Instruments and Controls

miles (mi) driven since the ignition was last turned on and the vehicle was moving. Once the vehicle begins moving, the trip odometer will accumulate mileage. For example, if the vehicle was driven 8 km (5 mi) before it is started again, and then the retroactive reset feature is activated, the display will show 8 km (5 mi). As the vehicle begins moving, the display will then increase to 8.2 km (5.1 mi), 8.4 km (5.2 mi), etc. If the retroactive reset feature is activated after the vehicle is started, but before it begins moving, the display will show the number of kilometers (km) or miles (mi) driven during the last ignition cycle.

OIL LIFE To access this display, the vehicle must be in P (Park). Press the trip odometer reset stem until OIL LIFE REMAINING displays. This display shows an estimate of the oil's remaining useful life. If you see 99% OIL LIFE REMAINING on the

display, that means 99% of the current oil life remains. The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5-37. You should change the oil as soon as you can. See Engine Oil on page 10-7. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule. See Maintenance Schedule on page 11-2. Remember, you must reset the OIL LIFE display yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change.

To reset the engine oil life system, see Engine Oil Life System on page 10-9.

PARK ASSIST To access this display, the vehicle must be in P (Park). If your vehicle has the Rear Parking Assist (RPA) system, press the trip odometer reset stem until PARK ASSIST displays. This display allows the system to be turned on or off. Once in this display, press and hold the trip odometer reset stem to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off. The RPA system automatically turns back on after each vehicle start. When the RPA system is turned off and the vehicle is shifted out of P (Park), the DIC will display the PARK ASSIST OFF message as a reminder that the system has been turned off. See Object Detection System Messages on page 5-39 and Parking Assist on page 9-35.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (33,1)

UNITS To access this display, the vehicle must be in P (Park). Press the trip odometer reset stem until UNITS displays. This display allows you to select between metric or English units of measurement. Once in this display, press and hold the trip odometer reset stem to select between METRIC or ENGLISH units. All of the vehicle information will then be displayed in the unit of measurement selected.

Instruments and Controls

5-33

DISPLAY LANGUAGE To access this display, the vehicle must be in P (Park). This display allows you to select the language in which the DIC messages will appear. To select a language: 1. Press the trip odometer reset

stem until DISPLAY LANGUAGE displays.

2. Continue to press and hold the

trip odometer reset stem to scroll through all of the available languages. The available languages are ENGLISH (default), FRANCAIS (French), ESPANOL (Spanish), and NO CHANGE.

3. Once the desired language is

displayed, release the trip odometer reset stem to set your choice.

SIDE BLIND ZONE ALERT If the vehicle has the Side Blind Zone Alert (SBZA) system, this display allows the system to be turned on or off. Once in this display, press the set/reset button to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off. When the SBZA system is turned off, the DIC will display the SIDE BLIND ZONE ALERT SYSTEM OFF message as a reminder that the system has been turned off. See Object Detection System Messages on page 5-39 and Side Blind Zone Alert (SBZA) on page 9-36.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (34,1)

5-34

Instruments and Controls

REAR CROSS TRAFFIC ALERT If the vehicle has the Rear Cross Traffic Alert (RCTA) system, this display allows the system to be turned on or off. Once in this display, press the set/reset button to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off. When the RCTA system is turned off, the DIC will display the REAR CROSS TRAFFIC ALERT SYSTEM OFF message as a reminder that the system has been turned off. See Object Detection System Messages on page 5-39 and Rear Vision Camera (RVC) on page 9-38.

Vehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action, but you can press any of the DIC buttons on the instrument panel or the trip odometer reset stem on the instrument panel cluster to acknowledge that you received the messages and to clear them from the display. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear, not correct the problem.

The following are the possible messages that can be displayed and some information about them.

Battery Voltage and Charging Messages

BATTERY LOW START VEHICLE This message displays when the system detects that the battery voltage has dropped to a critical level and the engine must be started to avoid a dead battery situation. BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping below expected levels. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that the features are disabled, this message is displayed. It means that the vehicle is trying to save the charge in the battery.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (35,1)

Turn off all unnecessary accessories to allow the battery to recharge. The normal battery voltage range is 11.5 to 15.5 volts. SERVICE BATTERY CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument cluster. See Charging System Light on page 5-17. Driving with this problem could drain the battery. Turn off all unnecessary accessories. Have the electrical system checked as soon as possible. See your dealer.

Instruments and Controls

5-35

Brake System Messages

Door Ajar Messages

SERVICE BRAKE SYSTEM This message displays along with the brake system warning light if there is a problem with the brake system. See Brake System Warning Light on page 5-20. If this message appears, stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display. If the message is still displayed or appears again when you begin driving, the brake system needs service as soon as possible. See your dealer.

Cruise Control Messages

CRUISE SET TO XXX This message displays whenever the cruise control is set. See Cruise Control on page 9-30 for more information.

DRIVER DOOR OPEN This message displays and a chime sounds if the driver door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. HOOD OPEN On some models, this message displays and a chime sounds if the hood is not fully closed. Stop and turn off the vehicle, check the hood for obstructions, and close the hood again. Check to see if the message still appears on the DIC.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (36,1)

5-36

Instruments and Controls

LEFT REAR DOOR OPEN This message displays and a chime sounds if the driver side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. LIFTGATE OPEN This message displays and a chime sounds if the liftgate is open while the ignition is in ON/RUN. Turn off the vehicle and check the liftgate. Restart the vehicle and check for the message on the DIC display. PASSENGER DOOR OPEN This message displays and a chime sounds if the passenger door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC.

POWER LIFTGATE OFF This message displays when the power liftgate has been turned off by pressing the power liftgate button on the center stack. RIGHT REAR DOOR OPEN This message displays and a chime sounds if the passenger side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC.

Engine Cooling System Messages

ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gauge on page 5-14. To avoid added strain on a hot engine, the air

conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive your vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. ENGINE OVERHEATED IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. See Engine Coolant Temperature Gauge on page 5-14. See Overheated Engine Protection Operating Mode on page 10-18 for information on driving to a safe place in an emergency.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (37,1)

Instruments and Controls

5-37

ENGINE OVERHEATED STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when service is required for the vehicle. See your dealer. See Engine Oil on page 10-7 and Maintenance Schedule on page 11-2.

Acknowledging the CHANGE ENGINE OIL SOON message will not reset the OIL LIFE REMAINING. See “Oil Life” under Driver Information Center (DIC) (With DIC Buttons) on page 5-25 or Driver Information Center (DIC) (Without DIC Buttons) on page 5-31 and Engine Oil Life System on page 10-9. ENGINE OIL LOW — ADD OIL On some vehicles, this message displays when the engine oil level may be too low. Check the oil level before filling to the recommended level. If the oil is not low and this message remains on, take the vehicle to your dealer for service. See Engine Oil on page 10-7.

OIL PRESSURE LOW STOP ENGINE This message displays when the vehicle's engine oil pressure is low. The oil pressure light also appears on the instrument cluster. See Engine Oil Pressure Light on page 5-24. Stop the vehicle immediately, as engine damage can result from driving a vehicle with low oil pressure. Have the vehicle serviced by your dealer as soon as possible when this message is displayed.

Engine Power Messages

ENGINE POWER IS REDUCED This message displays and a chime sounds when the cooling system temperature gets too hot and the engine further enters the engine coolant protection mode. See Engine Overheating on page 10-16
for further information.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (38,1)

5-38

Instruments and Controls

This message also displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW This message displays and a chime sounds if the fuel level is low. Refuel as soon as possible. See Fuel Gauge on page 5-13 and Fuel on page 9-43 for more information.

TIGHTEN GAS CAP This message may display along with the check engine light on the instrument cluster if the vehicle's fuel cap is not tightened properly. See Malfunction Indicator Lamp on page 5-18. Reinstall the fuel cap fully. See Filling the Tank on page 9-44. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn this light and message off.

Key and Lock Messages

REPLACE BATTERY IN REMOTE KEY This message displays if a Remote Keyless Entry (RKE) transmitter battery is low. The battery needs to be replaced in the transmitter. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-2.

Lamp Messages

AUTOMATIC LIGHT CONTROL OFF This message displays when the automatic headlamps are turned off. This message clears itself after 10 seconds. AUTOMATIC LIGHT CONTROL ON This message displays when the automatic headlamps are turned on. This message clears itself after 10 seconds. TURN SIGNAL ON This message displays and a chime sounds if a turn signal is left on for 1.2 km (0.75 mi). Move the turn signal lever to the off position.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (39,1)

Object Detection System Messages

FORWARD COLLISION ALERT UNAVAILABLE This message displays when attempting to activate the Forward Collision Alert (FCA) system when it is temporarily unavailable. The FCA system does not need service. This message could be due to the camera being blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. FRT CAMERA BLOCKED CLEAN WINDSHIELD This message displays when the camera is blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. The Lane Departure Warning system will not operate. Forward Collision Alert (FCA) may not work or may not work as well.

Instruments and Controls

5-39

LANE DEPARTURE SYS UNAVAILABLE This message displays when attempting to activate the Lane Departure Warning (LDW) system when it is temporarily unavailable. The LDW system does not need service. This message could be due to the camera being blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. PARK ASST BLOCKED SEE OWNERS MANUAL This message displays if there is something interfering with the Rear Parking Assist (RPA) system. See Parking Assist on page 9-35. PARK ASSIST OFF After the vehicle has been started, this message displays to remind the driver that the RPA system has

been turned off. To turn the RPA system back on, see Parking Assist on page 9-35. REAR CROSS TRAFFIC ALERT SYSTEM OFF If the vehicle has the Rear Cross Traffic Alert (RCTA) system, this message displays when the RCTA system has been turned off. See Rear Vision Camera (RVC) on page 9-38 and Driver Information Center (DIC) (With DIC Buttons) on page 5-25 or Driver Information Center (DIC) (Without DIC Buttons) on page 5-31. SERVICE FRONT CAMERA If this message remains on after continued driving, the vehicle needs service. Do not use the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) features. Take the vehicle to your dealer.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (40,1)

5-40

Instruments and Controls

SIDE BLIND ZONE ALERT SYSTEM OFF If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system has been turned off. See Side Blind Zone Alert (SBZA) on page 9-36 and Driver Information Center (DIC) (With DIC Buttons) on page 5-25 or Driver Information Center (DIC) (Without DIC Buttons) on page 5-31.

SERVICE PARK ASSIST This message displays if there is a problem with the Rear Parking Assist (RPA) system. Do not use this system to help you park. See Parking Assist on page 9-35. See your dealer for service. SERVICE SIDE DETECTION SYSTEM If your vehicle has the Side Blind Zone Alert (SBZA) system and this message displays, both SBZA displays will remain on indicating there is a problem with the SBZA system. If these displays remain on after continued driving, the system needs service. See your dealer. See Side Blind Zone Alert (SBZA) on page 9-36.

SIDE DETECTION SYS TEMPORARILY OFF If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system is disabled because the sensor cannot detect vehicles in your blind zone. The sensor may be blocked by mud, dirt, snow, ice, or slush. This message may also display during heavy rain or due to road spray. It may also come on when driving in isolated areas with no guardrails, trees, or road signs and light traffic. Your vehicle does not need service. For cleaning instructions, see “Washing the Vehicle” in Exterior Care on page 10-73. See Side Blind Zone Alert (SBZA) on page 9-36.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (41,1)

Instruments and Controls

5-41

Ride Control System Messages

SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak® system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive, however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly. SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. See Traction Control/ Electronic Stability Control on page 9-28 for more information.

TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly. See Traction Control/ Electronic Stability Control on page 9-28. TRACTION CONTROL ON This message displays when the Traction Control System (TCS) is turned on. See Traction Control/ Electronic Stability Control on page 9-28. This message clears itself after 10 seconds.

Airbag System Messages

SERVICE AIR BAG This message displays if there is a problem with the airbag system. Have your dealer inspect the system for problems. See Airbag Readiness Light on page 5-16 and Airbag System on page 3-22 for more information.

Security Messages

SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system. The vehicle may or may not restart so you may want to take the vehicle to your dealer before turning off the engine. See Immobilizer Operation on page 2-13 for more information. THEFT ATTEMPTED This message displays if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle. See Vehicle Alarm System on page 2-12 for more information.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (42,1)

5-42

Instruments and Controls

Service Vehicle Messages

SERVICE A/C (Air Conditioning) SYSTEM This message displays when the electronic sensors that control the air conditioning and heating systems are no longer working. Have the climate control system serviced by your dealer if you notice a drop in heating and air conditioning efficiency. SERVICE POWER STEERING This message displays when a problem is detected with the power steering system. When this message is displayed, you may notice that the effort required to steer the vehicle increases or feels heavier, but you will still be able to steer the vehicle. Have your vehicle serviced by your dealer immediately.

SERVICE VEHICLE SOON This message displays when a non-emissions related malfunction occurs. Have the vehicle serviced by your dealer as soon as possible. STARTING DISABLED SERVICE THROTTLE This message displays when your vehicle's throttle system is not functioning properly. Have your vehicle serviced by your dealer.

Tire Messages

TIRE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low.

This message also displays LEFT FRT (left front), RIGHT FRT (right front), LEFT RR (left rear), or RIGHT RR (right rear) to indicate the location of the low tire. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5-23. If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10-35, Vehicle Load Limits on page 9-9, and Tire Pressure on page 10-43. The DIC also shows the tire pressure values. See Driver Information Center (DIC) (With DIC Buttons) on page 5-25 or Driver Information Center (DIC) (Without DIC Buttons) on page 5-31.

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (43,1)

SERVICE TIRE MONITOR SYSTEM On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 5-23. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 10-45 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer.

Instruments and Controls

5-43

TIRE LEARNING ACTIVE This message displays when the Tire Pressure Monitor System (TPMS) is relearning the tire positions on your vehicle. The tire positions must be relearned after rotating the tires or after replacing a tire or sensor. See Tire Rotation on page 10-49, Tire Pressure Monitor System on page 10-44, and Tire Pressure on page 10-43 for more information.

Transmission Messages

ALL WHEEL DRIVE OFF If your vehicle has the All-Wheel Drive (AWD) system, this message displays when there is a temporary condition making the AWD system unavailable. The vehicle will run in 2WD. This could be caused by: . A compact spare tire on the

vehicle

. AWD system overheat

Loss of wheel or vehicle speed . Certain other vehicle electrical

conditions

This message turns off when the compact spare tire is replaced by a full-size tire, the differential fluid cools or the above conditions are no longer present and the warning message is reset. To reset the warning message manually, turn the ignition off and then back on again after 30 seconds. If the message stays on, see your dealer. See All-Wheel Drive on page 9-26. SERVICE ALL WHEEL DRIVE This message displays if a problem occurs with the All-Wheel Drive (AWD) system. The vehicle will run in 2WD. This could be caused by: . An electronics problem . Worn out or overheated clutch

plates

. Various electrical issues

Chevrolet Traverse Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7576032) - 2015 - CRC - 8/19/14

Black plate (44,1)