2009 Chevrolet Trailblazer Owners Manual

Download PDF Manual
this procedure if coolant begins to ﬂow out of the ﬁller neck, reinstall the pressure cap. Be sure the pressure cap is hand-tight and fully seated. If the pressure cap is not tightly installed, Notice: coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured. If the pressure cap is not tightly installed, Radiator Pressure Cap Notice: coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured. See Engine Compartment Overview on page 5-12 for information on location. 6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. 7. By this time, the coolant level inside the radiator ﬁller neck may be lower. If the level is lower, add more of the proper DEX-COOL coolant mixture through the ﬁller neck until the level reaches the base of the ﬁller neck. 5-34 If Steam Is Coming From The Engine Compartment { CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood. If you keep driving when your engine is overheated, the liquids in it can catch ﬁre. You or others could be badly burned. Stop your engine if it overheats, and get out of the vehicle until the engine is cool. Engine Overheating The vehicle has several indicators to warn of engine overheating. You will ﬁnd a coolant temperature gage on the vehicle’s instrument panel. See Engine Coolant Temperature Gage on page 3-38 for more information. If the vehicle has a Driver Information Center (DIC), the display will show an Engine Coolant Hot/Engine Overheated message. See DIC Warnings and Messages on page 3-51 for more information. You may decide not to lift the hood when this warning appears, but instead get service help right away. See Roadside Assistance Program on page 7-7. If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced. Notice: Engine damage from running the engine without coolant is not covered by the warranty. Notice: driven with no coolant, your vehicle can be badly damaged. The costly repairs would not be covered by the vehicle warranty. If the engine catches ﬁre because of being 5-35 If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: (cid:129) Climbs a long hill on a hot day. (cid:129) Stops after high-speed driving. Idles for long periods in traffic. Tows a trailer. If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest temperature and to the highest fan speed. Open the windows as necessary. 3. In heavy traffic, let the engine idle in N (Neutral) while stopped. If it is safe to do so, pull off the road, shift to P (Park) or N (Neutral) and let the engine idle. If the temperature overheat gage is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe 5-36 vehicle distance from the car in front of you. If the warning does not come back on, continue to drive normally. If the warning continues, pull over, stop, and park the vehicle right away. If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down. Engine Fan Noise The vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions the clutch is not engaged. This improves fuel economy and reduces fan noise. Under heavy vehicle loading, trailer towing, and/or high outside temperatures, the fan speed increases when the clutch engages so you may hear an increase in fan noise. This is normal and should not be mistaken as the transmission slipping or making extra shifts. It is merely the cooling system functioning properly. The fan will slow down when additional cooling is not required and the clutch disengages. You may also hear this fan noise when the engine is started. The sound will go away as the fan clutch disengages. (cid:129) (cid:129) Power Steering Fluid See Engine Compartment Overview on page 5-12 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise. A ﬂuid loss in this system could indicate a problem. Have the system inspected and repaired. How to Check Power Steering Fluid To check the power steering ﬂuid, do the following: 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag. 4. Replace the cap and completely tighten it. 5. Remove the cap again and look at the ﬂuid level on the dipstick. For vehicles with the 4.2L L6 engine, the level should be at the C (Cold) mark. For vehicles with the 5.3L or 6.0L V8 engines, the level should be at the FULL mark. If necessary, add only enough ﬂuid to bring the level up to the mark. What to Use To determine what kind of ﬂuid to use, see Recommended Fluids and Lubricants on page 6-12. Always use the proper ﬂuid. Failure to use the proper ﬂuid can cause leaks and damage hoses and seals. 5-37 Notice: (cid:129) When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water. (cid:129) Do not mix water with ready-to-use washer ﬂuid. Water can cause the solution to freeze and damage your washer ﬂuid tank and other parts of the washer system. Also, water does not clean as well as washer ﬂuid. Fill the washer ﬂuid tank only three-quarters full when it is very cold. This allows for ﬂuid expansion if freezing occurs, which could damage the tank if it is completely full. (cid:129) Do not use engine coolant (antifreeze) in your windshield washer. It can damage the vehicle’s windshield washer system and paint. Windshield Washer Fluid What to Use When the vehicle needs windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If the vehicle will be operating in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing. Adding Washer Fluid Open the cap with the washer symbol on it. Add washer ﬂuid until the tank is full. See Engine Compartment Overview on page 5-12 for reservoir location. 5-38 (cid:129) Brakes Brake Fluid The brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down: The brake ﬂuid level goes down because of normal brake lining wear. When new linings are installed, the ﬂuid level goes back up. (cid:129) A ﬂuid leak in the brake hydraulic system can also cause a low ﬂuid level. Have the brake hydraulic system ﬁxed, since a leak means that sooner or later the brakes will not work well. Do not top off the brake ﬂuid. Adding ﬂuid does not correct a leak. If ﬂuid is added when the linings are worn, there will be too much ﬂuid when new brake linings are installed. Add or remove brake ﬂuid, as necessary, only when work is done on the brake hydraulic system. { CAUTION: If too much brake ﬂuid is added, it can spill on the engine and burn, if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake ﬂuid only when work is done on the brake hydraulic system. See “Checking Brake Fluid” in this section. Refer to the Maintenance Schedule to determine when to check your brake ﬂuid. See Scheduled Maintenance on page 6-4. 5-39 (cid:129) Checking Brake Fluid Check brake ﬂuid by looking at the brake ﬂuid reservoir. See Engine Compartment Overview on page 5-12. { CAUTION: With the wrong kind of ﬂuid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake ﬂuid. Notice: (cid:129) Using the wrong ﬂuid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of ﬂuid. If brake ﬂuid is spilled on the vehicle’s painted surfaces, the paint ﬁnish can be damaged. Be careful not to spill brake ﬂuid on the vehicle. If you do, wash it off immediately. See Washing Your Vehicle on page 5-113. The ﬂuid level should be above MIN. If it is not, have the brake hydraulic system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is above the MIN, but not over the MAX mark. What to Add Use only new DOT-3 brake ﬂuid from a sealed container. See Recommended Fluids and Lubricants on page 6-12. Always clean the brake ﬂuid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir. 5-40 (cid:129) Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal ﬁrmly. { CAUTION: The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident. When the brake wear warning sound is heard, have the vehicle serviced. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair. Some driving conditions or climates can cause a brake squeal when the brakes are ﬁrst applied or lightly applied. This does not mean something is wrong with the brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque speciﬁcations in Capacities and Speciﬁcations on page 5-125. Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer/retailer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required. Brake Adjustment Every brake stop, the disc brakes adjust for wear. 5-41 Vehicle Storage { CAUTION: Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 5-43 for tips on working around a battery without getting hurt. Infrequent Usage: If the vehicle is driven infrequently, remove the black, negative (−) cable from the battery. This helps keep the battery from running down. Extended Storage: For extended storage of the vehicle, remove the black, negative (−) cable from the battery or use a battery trickle charger. This helps maintain the charge of the battery over an extended period of time. Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced — for example, when the brake linings wear down and new ones are installed — be sure to get new approved replacement parts. If this is not done, the brakes might not work properly. For example, if someone puts in brake linings that are wrong for the vehicle, the balance between the front and rear brakes can change — for the worse. The braking performance expected can change in many other ways if the wrong replacement brake parts are installed. Battery This vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. See Engine Compartment Overview on page 5-12 for battery location. Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. 5-42 Jump Starting If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION: Batteries can hurt you. They can be dangerous because: (cid:129) They contain acid that can burn you. (cid:129) They contain gas that can explode or ignite. (cid:129) They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you. Ignoring these steps could result in costly Notice: damage to the vehicle that would not be covered by the warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. If the other vehicle’s system is not a 12-volt Notice: system with a negative ground, both vehicles can be damaged. Only use vehicles with 12-volt systems with negative grounds to jump start your vehicle. 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles are not touching each other. If they are, it could cause a ground connection you do not want. You would not be able to start your vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake ﬁrmly on both vehicles involved in the jump start procedure. Put an automatic transmission in P (Park) or a manual transmission in N (Neutral) before setting the parking brake. If you have a four-wheel-drive vehicle, be sure the transfer case is not in N (Neutral). 5-43 { CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle. But if a battery has ﬁller caps, be sure the right amount of ﬂuid is there. If it is low, add water to take care of that ﬁrst. If you do not, explosive gas could be present. Battery ﬂuid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, ﬂush the place with water and get medical help immediately. If you leave the radio or other accessories Notice: on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3. Turn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlets, if equipped. Turn off the radio and all lamps that are not needed. This will avoid sparks and help to save both batteries. And it could save the radio! 4. Open both hoods and locate the batteries. Find the positive (+) and negative (−) terminals on each battery. Your vehicle has a remote negative (−) jump starting terminal. You should always use this remote terminal instead of the terminal on the battery. The remote negative (−) terminal is located on the front engine lift bracket on vehicles with the 4.2L L6 engine or the engine accessory drive bracket for vehicles with the 5.3L or 6.0L V8 engines, and is marked GND (Ground). See Engine Compartment Overview on page 5-12 for more information on location. 5-44 { CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative (−) will go to a heavy, unpainted metal engine part or to a remote negative (−) terminal if the vehicle has one. Do not connect positive (+) to negative (−) or you will get a short that would damage the battery and maybe other parts too. And do not connect the negative (−) cable to the negative (−) terminal on the dead battery because this can cause sparks. 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative (−) cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative (−) cable does not go to the dead battery. It goes to a heavy, unpainted metal engine part or to the remote negative (−) terminal on the vehicle with the dead battery. Your vehicle has a remote negative (−) terminal, marked GND, for this purpose. 5-45 9. Connect the other end of the negative (−) cable to the remote negative (−) terminal on the vehicle with the dead battery. 10. Now start the vehicle with the good battery and run the engine for a while. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service. If the jumper cables are connected or Notice: removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal. 4.2L L6 Engine 5.3L V8 Engine shown, 6.0L V8 Engine similar The remote negative (−) terminal is located on the front engine lift bracket for the 4.2L L6 engine, and on the accessory drive bracket for the 5.3L or 6.0L V8 engines. 5-46 Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part or Remote Negative (−) Terminal B. Good Battery or Remote Positive (+) and Remote Negative (−) Terminals C. Dead Battery or Remote Positive (+) Terminal To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery. 4. Disconnect the red positive (+) cable from the other vehicle. 5-47 All-Wheel Drive When to Check Lubricant It is not necessary to regularly check ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant If the level is below the bottom of the ﬁller plug hole, located on the transfer case, you’ll need to add some lubricant. Add enough lubricant to raise the level to the bottom of the ﬁller plug hole. Use care not to overtighten the plug. What to Use To determine what kind of lubricant to use, see Recommended Fluids and Lubricants on page 6-12. To get an accurate reading, the vehicle should be on a level surface. 5-48 Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. For all vehicles, excluding vehicles equipped with the 6.0L V8 Engine, the proper level is from 0 to 0.40 inch (0 to 10 mm) below the bottom of the ﬁller plug hole, located on the rear axle. For vehicles equipped with the 6.0L V8 Engine, the proper level is from 0.6 inch to 1.6 inches (15 mm to 40 mm) below the bottom of the ﬁller plug hole, located on the rear axle differential cover. Add only enough ﬂuid to reach the proper level. What to Use To determine what kind of lubricant to use, see Recommended Fluids and Lubricants on page 6-12. For vehicles equipped with the SS package, to add lubricant when the level is low, use SAE 75W–90 Synthetic Axle Lubricant (GM Part No. U.S. 12378261, in Canada 10953455) meeting GM Speciﬁcation 9986115. To completely reﬁll after draining, add 5.5 ounces (163 ml) of Limited-Slip Axle Lubricant Additive (GM Part No. U.S. 1052358, in Canada 992694). Then ﬁll to the bottom of the ﬁller plug hole with the Synthetic Gear Lubricant. 5-49 Four-Wheel Drive Transfer Case When to Check Lubricant It is not necessary to regularly check ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the ﬁller plug hole, you will need to add some lubricant. Add enough lubricant to raise the level to the bottom of the ﬁller plug hole. Use care not to overtighten the plug. What to Use To determine what kind of lubricant to use, see Recommended Fluids and Lubricants on page 6-12. 5-50 Front Axle When to Check Lubricant It is not necessary to regularly check front axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant If the level is below the bottom of the ﬁller plug hole, located on the front axle, you may need to add some lubricant. When the differential is cold, add enough lubricant to raise the level to 0.50 inch (12 mm) below the ﬁller plug hole. When the differential is at operating temperature (warm), add enough lubricant to raise the level to the bottom of the ﬁller plug hole. What to Use To determine what kind of lubricant to use, see Recommended Fluids and Lubricants on page 6-12. To get an accurate reading, the vehicle should be on a level surface. 5-51 Halogen Bulbs { CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package. Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However, if your vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if oncoming drivers ﬂash their high-beam headlamps at you (for vertical aim). If the headlamps need to be re-aimed, it is recommended that you take the vehicle to your dealer/retailer for service. Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-54. For any bulb changing procedure not listed in this section, contact your dealer/retailer. 5-52 Taillamps and Turn Signal Lamps 1. Open the liftgate. See Liftgate/Liftglass on page 2-13. 2. Remove the two screws from the taillamp assembly. 3. Pull the taillamp assembly away from the vehicle. 4. Unclip the wiring harness (A) and remove the three retaining screws (B) from the socket plate. 5. Remove the socket plate. 6. Holding the socket, pull the bulb to release it from the socket. 7. Push the new bulb into the socket until it clicks. 8. Reinstall the socket and tighten the three screws. 9. Reconnect the wiring harness. 10. Reinstall the taillamp assembly by lining up the locator pins with the retainers in the vehicle’s body. 11. Reinstall the two screws and tighten. 5-53 License Plate Lamp 1. Remove the two screws holding the license plate lamp lens. 3. Pull the old bulb straight out from the bulb socket. 4. Push the new bulb into the socket until it clicks. 5. Replace the lamp assembly lens and tighten the screws. Replacement Bulbs Exterior Lamp Bulb Number License Plate Lamp Taillamps W5W 3157 For replacement bulbs not listed here, contact your dealer/retailer. 2. Pull the lens away from the lamp assembly. 5-54 Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 6-4. Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not be covered by your warranty. Do not allow the wiper blade arm to touch the windshield. 1. To remove the old wiper blades, lift the wiper arm until it locks into a vertical position. A. Blade Assembly B. Arm Assembly C. Locking Tab 2. Press down on the blade assembly pivot locking D. Blade Pivot E. Hook Slot F. Arm Hook tab. Pull down on the blade assembly to release it from the wiper arm hook. 3. Remove the insert from the blade assembly. The insert has two notches at one end that are locked by the bottom claws of the blade assembly. At the notched end, pull the insert from the blade assembly. 5-55 4. To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A). Slide the insert all the way through the blade claws at the opposite end (B). The plastic caps (C) will be forced off as the insert is fully inserted. 5. Be sure that the notches are locked by the bottom claws. Make sure that all other claws are properly locked on both sides of the insert slots. 5-56 A. Claw in Notch B. Correct Installation C. Incorrect Installation 6. Put the blade assembly pivot in the wiper arm hook. Pull up until the pivot locking tab locks in the hook slot. 7. Carefully lower the wiper arm and blade assembly onto the windshield. Backglass Wiper Blade Replacement 3. Rotate the wiper blade assembly, and pull it off of the wiper arm. Hold the wiper arm in position and push the blade away from the wiper arm. 1. Lift the wiper blade assembly up and out of the park rest position. 2. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position, so care should be used when pulling it away from the vehicle. 4. Replace the wiper blade. 5. Return the wiper blade assembly to the park rest position. 5-57 CAUTION: (Continued) (cid:129) Underinﬂated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold. See Inﬂation - Tire Pressure on page 5-65. (cid:129) Overinﬂated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when you hit a pothole. Keep tires at the recommended pressure. (cid:129) Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them. See High-Speed Operation on page 5-66 for inﬂation pressure adjustment for high speed driving. Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. { CAUTION: (cid:129) Poorly maintained and improperly used tires are dangerous. (cid:129) Overloading your tires can cause overheating as a result of too much ﬂexing. You could have an air-out and a serious accident. See Loading the Vehicle on page 4-33. CAUTION: (Continued) 5-58 If the vehicle has low-proﬁle tires, Low-Proﬁle Performance Tire If your vehicle has P255/50R20 size tires, they are classiﬁed as low-proﬁle performance tires. These tires are designed for very responsive driving on wet or dry pavement. You may also notice more road noise with low-proﬁle performance tires and that they tend to wear faster. Notice: they are more susceptible to damage from road hazards or curb impact than standard proﬁle tires. Tire and/or wheel assembly damage can occur when coming into contact with road hazards like, potholes, or sharp edged objects, or when sliding into a curb. The vehicle warranty does not cover this type of damage. Keep tires set to the correct inﬂation pressure and, when possible avoid contact with curbs, potholes, and other road hazards. Winter Tires For cold weather driving conditions you may prefer to get tires designed for snow or ice, if your vehicle has P255/50R20 size tires. See your dealer for details regarding winter tire availability and proper tire selection. Also, see Buying New Tires on page 5-75. If you choose to use winter tires: (cid:129) Use tires of the same brand and tread type on all four wheel positions. (cid:129) Use only radial ply tires of the same size, load range, and speed rating as your original equipment tires. Winter tires with the same speed rating as your original equipment tires may not be available for H, V, W, Y and ZR speed rated tires. If you choose winter tires with a lower speed rating, never exceed the tire’s maximum speed capability. 5-59 Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The following illustration is an example of a typical P-Metric tire sidewall. Passenger (P-Metric) Tire (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail. 5-60 (B) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC speciﬁcation code molded onto the sidewall. GM’s TPC speciﬁcations meet or exceed all federal safety guidelines. (C) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. (D) Tire Identiﬁcation Number (TIN): The letters and numbers following DOT code are the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information, see Uniform Tire Quality Grading on page 5-78. (G) Maximum Cold Inﬂation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommended tire pressure see Inﬂation - Tire Pressure on page 5-65 and Loading the Vehicle on page 4-33. Tire Size The following examples show the different parts of a tire size. Passenger (P-Metric) Tire (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 75, as shown in item C of the passenger (P-Metric) tire illustration, it would mean that the tire’s sidewall is 75 percent as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches. (F) Service Description: The service description indicates the load range and speed rating of a tire. The load index can range from 1 to 279. Speed ratings range from A to Z. 5-61 Tire Terminology and Deﬁnitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire’s height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inﬂation - Tire Pressure on page 5-65. Curb Weight: The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) motor vehicle safety standards. The DOT code includes the Tire Identiﬁcation Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR: Gross Vehicle Weight Rating. See Loading the Vehicle on page 4-33. GAWR FRT: Gross Axle Weight Rating for the front axle. See Loading the Vehicle on page 4-33. GAWR RR: Gross Axle Weight Rating for the rear axle. See Loading the Vehicle on page 4-33. 5-62 Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inﬂation Pressure: The maximum air pressure to which a cold tire can be inﬂated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inﬂation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading the Vehicle on page 4-33. Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inﬂation Pressure: Vehicle manufacturer’s recommended tire inﬂation pressure as shown on the tire placard. See Inﬂation - Tire Pressure on page 5-65 and Loading the Vehicle on page 4-33. 5-63 Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1/16 inch (1.6 mm) of tread remains. See When It Is Time for New Tires on page 5-74. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 5-78. Vehicle Capacity Weight: The number of designated seating positions multiplied by 150 lbs (68 kg) plus the rated cargo load. See Loading the Vehicle on page 4-33. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle’s capacity weight and the original equipment tire size and recommended inﬂation pressure. See “Tire and Loading Information Label” under Loading the Vehicle on page 4-33. 5-64 Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: (cid:129) Too much ﬂexing (cid:129) Too much heat (cid:129) Tire overloading (cid:129) Premature or irregular wear (cid:129) Poor handling (cid:129) Reduced fuel economy If your tires have too much air (over-inﬂation), you can get the following: (cid:129) Unusual wear (cid:129) Poor handling (cid:129) Rough ride (cid:129) Needless damage from road hazards A vehicle speciﬁc Tire and Loading Information label is attached to your vehicle. This label shows your vehicle’s original equipment tires and the correct inﬂation pressures for your tires when they are cold. The recommended cold tire inﬂation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity. For additional information regarding how much weight your vehicle can carry, and an example of the Tire and Loading Information label, see Loading the Vehicle on page 4-33. How you load your vehicle affects vehicle handling and ride comfort. Never load your vehicle with more weight than it was designed to carry. When to Check Check your tires once a month or more. Do not forget to check the pressure of the spare tire, if the vehicle has one. See Spare Tire on page 5-109 for additional information. 5-65 High-Speed Operation { CAUTION: Driving at high speeds, 100 mph (160 km/h) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. You could have a crash and you or others could be killed. Some high-speed rated tires require inﬂation pressure adjustment for high speed operation. When speed limits and road conditions are such that a vehicle can be driven at high speeds, make sure the tires are rated for high speed operation, in excellent condition, and set to the correct cold tire inﬂation pressure for the vehicle load. How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are underinﬂated. Check the tire’s inﬂation pressure when the tires are cold. Cold means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Remove the valve cap from the tire valve stem. Press the tire gage ﬁrmly onto the valve to get a pressure measurement. If the cold tire inﬂation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the pressure is low, add air until you reach the recommended amount. If you overﬁll the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture. 5-66 If your vehicle has P255/50R20 104V size tires installed on the rear axle, they will require inﬂation pressure adjustment when driving your vehicle at speeds above 99 mph (160 km/h). Set the cold inﬂation pressure, for the rear tires only, to the maximum inﬂation pressure shown on the tire sidewall, or 38 psi (262 kPa), whichever is lower. See the example following. When you end this high-speed driving, return the tires to the cold tire inﬂation pressure shown on the Tire and Loading Information label. See Loading the Vehicle on page 4-33. Example: You will ﬁnd the maximum load and inﬂation pressure molded on the tire’s sidewall, in small letters, near the rim ﬂange. It will read something like this: Maximum load 690 kg (1521 lbs) 300 kPa (44 psi) Max. Press. For this example, you would set the inﬂation pressure for high-speed driving at 38 psi (262 kPa). The inﬂation pressure for the front tires should be set to the cold tire inﬂation pressure shown on the Tire and Loading Information label. Racing or other competitive driving may affect the warranty coverage of your vehicle. See your warranty booklet for more information. Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inﬂated to the inﬂation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inﬂation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inﬂation pressure label, you should determine the proper tire inﬂation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is signiﬁcantly under-inﬂated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inﬂate them to the proper pressure. Driving on a signiﬁcantly under-inﬂated tire causes the tire to overheat and can lead to tire failure. Under-inﬂation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. 5-67 Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inﬂation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will ﬂash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation on page 5-69 for additional information. 5-68 Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The TPMS operates on a radio frequency and complies with RSS-210 of Industry and Science Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly, if the vehicle has one. The TPMS sensors monitor the air pressure in the vehicle’s tires and transmit the tire pressure readings to a receiver located in the vehicle. The TPMS is designed to alert the driver if a low tire pressure condition exists. If your vehicle has the Driver Information Center (DIC) steering wheel control buttons, tire pressure levels may also be checked through the DIC. See “Tire Pressures” under DIC Operation and Displays on page 3-48. When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument panel cluster. At the same time a message to check the pressure in a speciﬁc tire appears on the Driver Information Center (DIC) display. The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inﬂated to the correct inﬂation pressure. Using the DIC, tire pressure levels can be viewed by the driver. For additional information and details about the DIC operation and displays see DIC Operation and Displays on page 3-48 and DIC Warnings and Messages on page 3-51. The low tire pressure warning light may come on in cool weather when the vehicle is ﬁrst started, and then turn off as you start to drive. This could be an early indicator that the air pressure in the tire(s) is low and needs to be inﬂated to the proper pressure. A Tire and Loading Information label, attached to your vehicle, shows the size of your vehicle’s original equipment tires and the correct inﬂation pressure for your vehicle’s tires when they are cold. See Loading the Vehicle on page 4-33, for an example of the Tire and Loading Information label and its location on your vehicle. Also see Inﬂation - Tire Pressure on page 5-65. 5-69 Your vehicle’s TPMS can alert you about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection and Rotation on page 5-73 and Tires on page 5-58. Notice: Using non-approved tire sealants could damage the Tire Pressure Monitor System (TPMS) sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use the GM approved tire sealant available through your dealer/retailer. Factory-installed Tire Inﬂator Kits use a GM approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See Tire Sealant and Compressor Kit for information regarding the inﬂator kit materials and instructions. TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light ﬂashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message is also displayed. The low tire warning light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause the malfunction light and DIC message to come on are: (cid:129) One of the road tires has been replaced with the spare tire, if the vehicle has one. The spare tire does not have a TPMS sensor. The TPMS malfunction light and DIC message should go off once you re-install the road tire containing the TPMS sensor. The TPMS sensor matching process was started but not completed or not completed successfully after rotating the vehicle’s tires. The DIC message and TPMS malfunction light should go off once the TPMS sensor matching process is performed successfully. See “TPMS Sensor Matching Process” later in this section. 5-70 (cid:129) (cid:129) One or more TPMS sensors are missing or damaged. The DIC message and the TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer/retailer for service. (cid:129) Replacement tires or wheels do not match your vehicle’s original equipment tires or wheels. Tires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly. See Buying New Tires on page 5-75. (cid:129) Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction. If the TPMS is not functioning it cannot detect or signal a low tire condition. See your dealer/retailer for service if the TPMS malfunction light and DIC message come on and stay on. TPMS Sensor Matching Process Each TPMS sensor has a unique identiﬁcation code. Any time you rotate your vehicle’s tires or replace one or more of the TPMS sensors, the identiﬁcation codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool. See your dealer/retailer for service. The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire’s air pressure. If increasing the tire’s air pressure, do not exceed the maximum inﬂation pressure indicated on the tire’s sidewall. To decrease air-pressure out of a tire you can use the pointed end of the valve cap, a pencil-style air pressure gage, or a key. 5-71 You have two minutes to match the ﬁrst tire/wheel position, and ﬁve minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the ﬁrst tire and wheel, or more than ﬁve minutes to match all four tire and wheel positions the matching process stops and you need to start over. The TPMS sensor matching process is outlined below: 1. Set the parking brake. 2. Turn the ignition switch to ON/RUN with the engine off. 3. Turn the headlamp control from off to parking lamps four times within three seconds. A double horn chirp will sound and the TPMS low tire warning light will begin to ﬂash. The double horn chirp and ﬂashing TPMS warning light indicate that the TPMS matching process has started. The TPMS warning light should continue ﬂashing throughout the matching procedure. 4. Start with the driver side front tire. 5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire’s air pressure for 10 seconds, then stop and listen for a single horn chirp. The single horn chirp should sound within 15 seconds, conﬁrming that the sensor identiﬁcation code has been matched to this tire and wheel position. If you do not hear the conﬁrming single horn chirp, you will need to start over with step number one. 6. Proceed to the passenger side front tire, and repeat the procedure in Step 5. 7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5. 8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. 9. After hearing the conﬁrming horn chirp for the driver’s side rear tire, check to see if the TPMS warning light is still ﬂashing. If yes, turn the ignition switch to LOCK/OFF to exit the sensor matching process. If the TPMS warning light is not ﬂashing, the ﬁve minute time limit has passed and you will need to start the process over beginning with Step 1. 10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label. 11. Put the valve caps back on the valve stems. 5-72 Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, if the vehicle has one, for signs of wear or damage. See When It Is Time for New Tires on page 5-74 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). See Scheduled Maintenance on page 6-4. The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle. This will ensure that your vehicle continues to perform most like it did when the tires were new. Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-74 and Wheel Replacement on page 5-80. When rotating your tires, always use the correct rotation pattern shown here. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label. See Inﬂation - Tire Pressure on page 5-65 and Loading the Vehicle on page 4-33. 5-73 Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 5-69. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Speciﬁcations on page 5-125. When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions, inﬂuence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. Some commercial truck tires may not have treadwear indicators. { CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See Changing a Flat Tire on page 5-93. Make sure the spare tire, if the vehicle has one, is stored securely. Push, pull, and then try to rotate or turn the tire. If it moves, tighten the cable. See Storing a Flat or Spare Tire and Tools on page 5-106. 5-74 You need new tires if any of the following statements are true: (cid:129) You can see the indicators at three or more places around the tire. (cid:129) You can see cord or fabric showing through the tire’s rubber. The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric. The tire has a bump, bulge, or split. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage. The rubber in tires degrades over time, even if they are not being used. This is also true for the spare tire, if your vehicle has one. Multiple conditions affect how fast this aging takes place, including temperatures, loading conditions, and inﬂation pressure maintenance. With proper care and maintenance tires will typically wear out before they degrade due to age. If you are unsure about the need to replace your tires as they get older, consult the tire manufacturer for more information. Buying New Tires GM has developed and matched speciﬁc tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Speciﬁcation (TPC spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating. This way, your vehicle will continue to have tires that are designed to give the same performance and vehicle safety, during normal use, as the original tires. GM’s exclusive TPC Spec system considers over a dozen critical speciﬁcations that impact the overall performance of your vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM’s TPC Spec number is molded onto the tire’s sidewall near the tire size. If the tires have an all-season tread design, the TPC spec number will be followed by a MS, for mud and snow. See Tire Sidewall Labeling on page 5-60 for additional information. 5-75 (cid:129) (cid:129) (cid:129) GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle. See Tire Inspection and Rotation on page 5-73 for information on proper tire rotation. { CAUTION: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes, brands, or types (radial and bias-belted tires) the vehicle may not handle properly, and you could have a crash. Using tires of different sizes, brands, or types may also cause damage to your vehicle. Be sure to use the correct size, brand, and type of tires on your vehicle’s wheels. { CAUTION: If you use bias-ply tires on the vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on the vehicle. If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction type (radial and bias-belted tires) as your vehicle’s original tires. Vehicles equipped with a tire pressure monitoring system may give an inaccurate low-pressure warning if non-TPC spec rated tires are installed on your vehicle. Non-TPC Spec rated tires may give a low-pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires. See Tire Pressure Monitor System on page 5-67. 5-76 Your vehicle’s original equipment tires are listed on the Tire and Loading Information Label. See Loading the Vehicle on page 4-33, for more information about the Tire and Loading Information Label and its location on your vehicle. Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this could affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover. Additionally, if your vehicle has electronic systems such as anti-lock brakes, rollover airbags, traction control, and electronic stability control, the performance of these systems can be affected. { CAUTION: If you add different sized wheels, your vehicle may not provide an acceptable level of performance and safety if tires not recommended for those wheels are selected. You may increase the chance that you will crash and suffer serious injury. Only use GM speciﬁc wheel and tire systems developed for your vehicle, and have them properly installed by a GM certiﬁed technician. See Buying New Tires on page 5-75 and Accessories and Modiﬁcations on page 5-3 for additional information. 5-77 Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart signiﬁcantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. 5-78 Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on speciﬁed government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. { WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. { WARNING: The temperature grade for this tire is established for a tire that is properly inﬂated and not overloaded. Excessive speed, underinﬂation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. 5-79 Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment might need to be checked. If you notice your vehicle vibrating when driving on a smooth road, the tires and wheels might need to be rebalanced. See your dealer/retailer for proper diagnosis. Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer/retailer if any of these conditions exist. Your dealer/retailer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, wheel nuts, and TPMS sensors for your vehicle. { CAUTION: Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts, and wheel nuts for replacement. 5-80 Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See Changing a Flat Tire on page 5-93 for more information. Used Replacement Wheels { CAUTION: Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel. Tire Chains { CAUTION: Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on the vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions. To help avoid damage to the vehicle, drive slowly, re-adjust or remove the device if it is contacting the vehicle, and do not spin the wheels. If you do ﬁnd traction devices that will ﬁt, install them on the rear tires. 5-81 If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the ﬂat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel ﬁrmly. Steer to maintain lane position, and then gently brake to a stop well out of the traffic lane. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop, well off the road if possible. { CAUTION: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a ﬂat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a ﬂat tire. This vehicle may come with a jack and spare tire or a tire sealant and compressor kit. To use the jack and spare tire, see Changing a Flat Tire on page 5-93. To use the tire sealant and compressor kit, see Tire Sealant and Compressor Kit on page 5-83. 5-82 Tire Sealant and Compressor Kit { CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 2-38. { CAUTION: Over-inﬂating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inﬂate the tire to its recommended pressure. Do not exceed the recommended pressure. { CAUTION: Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location. If this vehicle has a tire sealant and compressor kit, there may not be a spare tire, tire changing equipment, and on some vehicles there may not be a place to store a tire. 5-83 This vehicle may have one of the following tire sealant and compressor kits. The kit includes: The tire sealant and compressor can be used to temporarily seal punctures up to 1⁄4 inch (6 mm) in the tread area of the tire. It can also be used to inﬂate an under inﬂated tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program on page 7-7. Read and follow all of the tire sealant and compressor kit instructions. 5-84 A. Selector Switch (Sealant/Air or Air Only) B. On/Off Button C. Pressure Gage D. Pressure Deﬂation Button (If equipped) E. Tire Sealant Canister F. Sealant/Air Hose (Clear) G. Air Only Hose (Black) H. Power Plug Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer/retailer. See “Removal and Installation of the Sealant Canister” following. There is only enough sealant to seal one tire. After usage, the sealant canister and sealant/air hose assembly must be replaced. See “Removal and Installation of the Sealant Canister” following. 5-85 Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inﬂate a Punctured Tire Follow the directions closely for correct sealant usage. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes. This will help to inﬂate the tire faster. Always do a safety check ﬁrst. See If a Tire Goes Flat on page 5-82. Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and compressor kit from its storage location. See Tire Sealant and Compressor Kit Storage on page 5-92. 2. Unwrap the sealant/air hose (F) and the power plug (H). 5-86 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4. Remove the valve stem cap from the ﬂat tire by turning it counterclockwise. 5. Attach the sealant/air hose (F) onto the tire valve stem. Turn it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Accessory Power Outlet(s) on page 3-19. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window. 7. Start the vehicle. The vehicle must be running while using the air compressor. 8. Turn the selector switch (A) counterclockwise to the Sealant + Air position. 9. Press the on/off (B) button to turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gage (C) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inﬂates with air only. 10. Inﬂate the tire to the recommended inﬂation pressure using the pressure gage (C). The recommended inﬂation pressure can be found on the Tire and Loading Information label. See Inﬂation - Tire Pressure on page 5-65. The pressure gage (C) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached. If the recommended pressure cannot be Notice: reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inﬂate the tire. Remove the power plug from the accessory power outlet and unscrew the inﬂating hose from the tire valve. See Roadside Assistance Program on page 7-7. 11. Press the on/off button (B) to turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire, therefore, Steps 12 through 18 must be done immediately after Step 11. Be careful while handling the tire sealant and compressor kit as it could be warm after usage. 5-87 12. Unplug the power plug (H) from the accessory power outlet in the vehicle. 13. Turn the sealant/air hose (F) counterclockwise to remove it from the tire valve stem. 14. Replace the tire valve stem cap. 15. Replace the sealant/air hose (F), and the power plug (H) back in their original location. 16. If the ﬂat tire was able to inﬂate to the recommended inﬂation pressure, remove the maximum speed label from the sealant canister (E) and place it in a highly visible location. The label is a reminder not to exceed 55 mph (90 km/h) until the damaged tire is repaired or replaced. 17. Return the equipment to its original storage location in the vehicle. 18. Immediately drive the vehicle 5 miles (8 km) to distribute the sealant in the tire. 5-88 19. Stop at a safe location and check the tire pressure. Refer to Steps 1 through 11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inﬂate a Tire (Not Punctured).” If the tire pressure has fallen more than 10 psi (68 kPa) below the recommended inﬂation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program on page 7-7. If the tire pressure has not dropped more than 10 psi (68 kPa) from the recommended inﬂation pressure, inﬂate the tire to the recommended inﬂation pressure. 20. Wipe off any sealant from the wheel, tire, and vehicle. 21. Dispose of the used sealant canister (E) and sealant/air hose (F) assembly at a local dealer/ retailer or in accordance with local state codes and practices. 22. Replace it with a new canister available from your dealer/retailer. 23. After temporarily sealing a tire using the tire sealant and compressor kit, take the vehicle to an authorized dealer/retailer within a 100 miles (161 km) of driving to have the tire repaired or replaced. Using the Tire Sealant and Compressor Kit without Sealant to Inﬂate a Tire (Not Punctured) To use the air compressor to inﬂate a tire with air only and not sealant: Always do a safety check ﬁrst. See If a Tire Goes Flat on page 5-82. 1. Remove the tire sealant and compressor kit from its storage location. See Tire Sealant and Compressor Kit Storage on page 5-92. 2. Unwrap the air only hose (G) and the power plug (H). 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 5-89 4. Remove the tire valve stem cap from the ﬂat tire by turning it counterclockwise. 5. Attach the air only hose (G) onto the tire valve stem by turning it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Accessory Power Outlet(s) on page 3-19. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window. 7. Start the vehicle. The vehicle must be running while using the air compressor. 8. Turn the selector switch (A) clockwise to the Air Only position. 9. Press the on/off (B) button to turn the compressor on. The compressor will inﬂate the tire with air only. 10. Inﬂate the tire to the recommended inﬂation pressure using the pressure gage (C). The recommended inﬂation pressure can be found on the Tire and Loading Information label. See Inﬂation - Tire Pressure on page 5-65. The pressure gage (C) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate reading. The compressor may be turned on/off until the correct pressure is reached. If you inﬂate the tire higher than the recommended pressure you can adjust the excess pressure by pressing the pressure deﬂation button (D), if equipped, until the proper pressure reading is reached. This option is only functional when using the air only hose (G). 11. Press the on/off button (B) to turn the tire sealant and compressor kit off. Be careful while handling the tire sealant and compressor kit as it could be warm after usage. 5-90 12. Unplug the power plug (H) from the accessory power outlet in the vehicle. 13. Disconnect the air only hose (G) from the tire valve stem, by turning it counterclockwise, and replace the tire valve stem cap. 14. Replace the air only hose (G) and the power plug (H) and cord back in its original location. 15. Place the equipment in the original storage location in the vehicle. The tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inﬂate air mattresses, balls, etc. Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Unwrap the sealant hose. Without Pressure Deﬂation Button With Pressure Deﬂation Button 2. Press the canister release button. 3. Pull up and remove the canister. 4. Replace with a new canister which is available from your dealer/retailer. 5. Push the new canister into place. 5-91 Tire Sealant and Compressor Kit Storage The tire sealant and compressor kit is located in the ﬂoor storage compartment at the rear of the vehicle. 1. Open the liftgate. See Liftgate/Liftglass on page 2-13. 2. Open the rear ﬂoor storage lid. See Rear Floor Storage Cover on page 2-55. 3. Remove the straps. 4. Remove the tire sealant and compressor kit from the storage compartment. 5. Remove tire sealant and compressor kit from the storage bag. The tire sealant and compressor kit is attached to the ﬂoor with two straps. 5-92 Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning ﬂashers. See Hazard Warning Flashers on page 3-6. { CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1. Set the parking brake ﬁrmly. 2. Put the shift lever in P (Park). 3. If you have a four-wheel-drive vehicle, be sure the transfer case is in a drive gear — not in Neutral. 4. Turn off the engine and do not restart while the vehicle is raised. CAUTION: (Continued) CAUTION: (Continued) 5. Do not allow passengers to remain in the vehicle. 6. Put the wheel blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire on the other side, at the opposite end of the vehicle. When the vehicle has a ﬂat tire (B), use the following example as a guide to assist you in the placement of wheel blocks (A). A. Wheel Block B. Flat Tire The following information explains how to use the jack and change a tire. 5-93 Removing the Spare Tire and Tools The tools you will be using include: A. Wheel Wrench B. Wheel Blocks C. Extension(s) (Socket End) D. Handle (Jack End) E. Jack The jacking equipment needed to remove the spare tire is stored under the rear seat. To release the jack from its

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2009 Chevrolet Trailblazer Owners Manual