2008 Chevrolet Trailblazer Owners Manual

Download PDF Manual
Features and Controls Keys ...............................................................2-3 Remote Keyless Entry (RKE) System ................2-4 Remote Keyless Entry (RKE) System Operation ...................................................2-5 Doors and Locks .............................................2-6 Door Locks ....................................................2-6 Power Door Locks ..........................................2-7 Delayed Locking .............................................2-7 Programmable Automatic Door Locks ................2-8 Rear Door Security Locks ..............................2-10 Lockout Protection ........................................2-11 Liftgate/Liftglass ............................................2-11 Windows ........................................................2-12 Power Windows ............................................2-13 Sun Visors ...................................................2-14 Theft-Deterrent Systems ..................................2-15 Content Theft-Deterrent .................................2-15 Passlock® (U. S. Only) ..................................2-16 PASS-Key® III+ Electronic Immobilizer .............2-17 PASS-Key® III+ Electronic Immobilizer Operation (Canada Only) ............................2-17 Starting and Operating Your Vehicle ................2-19 New Vehicle Break-In ....................................2-19 Ignition Positions ..........................................2-20 Retained Accessory Power (RAP) ...................2-21 Starting the Engine .......................................2-21 Adjustable Throttle and Brake Pedal ................2-22 Engine Coolant Heater ..................................2-23 Active Fuel Management™ .............................2-24 Automatic Transmission Operation ...................2-24 Four-Wheel Drive ..........................................2-28 Parking Brake ..............................................2-32 Shifting Into PARK (P) ...................................2-33 Shifting Out of PARK (P) ...............................2-35 Parking Over Things That Burn .......................2-35 Engine Exhaust ............................................2-36 Running the Vehicle While Parked ..................2-36 Mirrors ...........................................................2-37 Manual Rearview Mirror .................................2-37 Manual Rearview Mirror with OnStar® ..............2-38 Automatic Dimming Rearview Mirror with OnStar® and Compass ...............................2-38 Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display ....................................................2-40 Automatic Dimming Rearview Mirror with Compass and Temperature Display ..............2-42 Outside Manual Mirrors ..................................2-45 Outside Power Mirrors ...................................2-45 Outside Curb View Assist Mirror .....................2-46 Outside Convex Mirror ...................................2-46 Outside Heated Mirrors ..................................2-46 2-1 Section 2 Features and Controls OnStar® System .............................................2-47 Universal Home Remote System ......................2-50 Universal Home Remote System Operation (With One Triangular LED) ...........................2-51 Storage Areas ................................................2-55 Glove Box ...................................................2-55 Overhead Console ........................................2-55 Center Console Storage .................................2-55 Luggage Carrier ...........................................2-56 Rear Floor Storage Lid ..................................2-57 Convenience Net ..........................................2-57 Cargo Cover ................................................2-57 Cargo Tie Downs ..........................................2-58 Sunroof .........................................................2-58 2-2 Keys {CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and they could be seriously injured or killed if caught in the path of a closing window. Do not leave the keys in a vehicle with children. This vehicle has keys that can be used for the ignition and door lock that will ﬁt with either side up. When a new vehicle is delivered, the dealer/retailer provides the owner with a pair of identical keys and a key code number. 2-3 The key code number tells your dealer/retailer or a qualiﬁed locksmith how to make extra keys. Keep this number in a safe place. If you lose your keys, you will be able to have new ones made easily using this number. Your selling dealer/retailer should also have this number. Notice: you may have to damage the vehicle to get in. Be sure you have spare keys. If you ever get locked out of your vehicle, call the Roadside Assistance Center. See Roadside Assistance Program on page 7-7. If you ever lock your keys in your vehicle, Remote Keyless Entry (RKE) System If the vehicle has the Remote Keyless Entry (RKE) system, it operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. At times you may notice a decrease in range. This is normal for any RKE system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: (cid:127) Check the distance. The transmitter may be too far from the vehicle. It may be necessary to stand closer during rainy or snowy weather. (cid:127) Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. (cid:127) Check the transmitter’s battery. See “Battery Replacement” later in this section. (cid:127) If the transmitter is still not working correctly, see your dealer/retailer or a qualiﬁed technician for service. 2-4 Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions will work up to 30 feet (9 m) away. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-4. K (Unlock): Press K to unlock the driver’s door. The parking lamps will ﬂash and the interior lights will come on. Press K a second time within three seconds to unlock all the doors. You can program different feedback settings through the Driver Information Center (DIC). For more information see Driver Information Center (DIC) on page 3-49. Q (Lock): Press Q to lock all the doors. Press Q again within three seconds and the horn will chirp. L (Panic): Press L to make the horn sound. The headlamps and taillamps will ﬂash for up to 30 seconds. This can be turned off by pressing L again, by waiting for 30 seconds, or by starting the vehicle. Matching Transmitter(s) to Your Vehicle Each RKE transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer/retailer. All transmitters need to be re-coded to match the new transmitter. The lost transmitter will no longer work after the new transmitters are re-coded. Each vehicle can have a maximum of four transmitters matched to it. Battery Replacement Replace the battery if the KEY FOB # BATTERY LOW message displays in the DIC. See “KEY FOB # BATTERY LOW” under DIC Warnings and Messages on page 3-53 for additional information. Notice: When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. 2-5 To replace the battery in the RKE transmitter do the following: Doors and Locks Door Locks {CAUTION: Unlocked doors can be dangerous. (cid:127) Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. (cid:127) Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it. (cid:127) Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. 1. Separate the halves of the transmitter with a ﬂat, thin object inserted into the slot between the covers of the transmitter housing. 2. Remove the old battery. Do not use a metal object. 3. Insert the new battery. Replace with a CR2032 or equivalent battery. 4. Put the transmitter back together tightly. 2-6 There are several ways to lock and unlock your vehicle. You can use the remote keyless entry transmitter. You can use your key to unlock your door from the outside. Power Door Locks You can lock or unlock the door from the inside by sliding the manual lever forward or rearward. The power door lock switches are located on the driver’s and front passenger’s door armrests. When the door is unlocked, you can see a red area on the lever. The manual lever on each door works only that door’s lock. Press the lock symbol to lock all of the doors. To unlock the doors, press the other side of the switch. Delayed Locking This feature delays the locking of the doors and the liftgate when using the power lock or the remote keyless entry system. The ﬁrst press of the power door lock switch or lock button on the remote keyless entry transmitter with the driver’s door open will activate the delay locking. A chime will sound. All doors and the liftgate can be reopened for up to ﬁve seconds from the time the last door is closed. 2-7 Five seconds after the last door is closed, all the doors will lock. You can lock the doors immediately by using the power door lock switch or by pressing the lock button on the optional remote keyless entry transmitter a second time. If the key is inserted in the ignition, this feature will not lock the doors. See Lockout Protection on page 2-11. You can turn the delayed locking feature on or off. If the feature is turned off, the doors will lock immediately when a power door lock switch or remote keyless entry transmitter lock button is pressed. Programming Delayed Locking To turn the delayed locking feature on or off, do the following: 1. Press and hold the power door lock switch on the driver’s door in the lock position. 2. Press the remote keyless entry transmitter unlock button twice. If the delayed locking feature was on, it will now be off. If the feature was off, it will now be on. Programmable Automatic Door Locks Your vehicle is equipped with an automatic lock/unlock feature which enables you to program your vehicle’s power door locks. You can program this feature through the Driver Information Center (DIC), or by the following method. See DIC Vehicle Customization on page 3-58. Programmable Locking Feature Following are the two locking modes that can be programmed: Mode 1: All doors lock when the transmission is shifted out of PARK (P). Mode 2: All doors lock when the vehicle speed is greater than 8 mph (13 km/h). The automatic door locks were pre-programmed at the factory to lock all the doors when the transmission is shifted into gear. The following instructions detail how to program your door locks differently than the factory setting. Choose one of the two programming options listed previously before entering the program mode. 2-8 To enter the program mode, do the following: 1. Begin with the ignition off. Then pull the turn signal/multifunction lever toward you and hold it there while you perform the next step. 2. Turn the key to RUN and LOCK twice. Then, with the key in LOCK, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30-second program timer will begin. 3. You are now ready to program the automatic door locks. Select one of the two programming options listed previously, and press the lock side of the power door lock switch to cycle through the lock options. You will have 30 seconds to begin programming. If you exceed the 30-second limit, the locks will automatically lock and unlock and the horn will chirp twice to indicate that you have left the program mode. If this occurs, repeat the procedure beginning with Step 1 to re-enter the programming mode. You can exit the program mode any time by turning the ignition to RUN. The locks will automatically lock and unlock and the horn will chirp twice to indicate that you are leaving the program mode. If the lock/unlock switches are not pressed while in the programming mode, the current auto lock/unlock setting will not be modiﬁed. See your dealer for more information. Programmable Unlocking Feature The following is the list of available programming options: Mode 1: Driver’s door unlocks when the transmission is shifted into PARK (P). Mode 2: All doors unlock when the transmission is shifted into PARK (P). Mode 3: All doors unlock when the key is removed from the ignition. Mode 4: No automatic door unlock. The automatic door locks were pre-programmed at the factory to unlock all doors once the transmission is shifted to PARK (P). The following instructions detail how to program your door locks differently than the factory setting. Choose one of the four programming options listed previously before entering the program mode. 2-9 To enter the program mode you need to do the following: 1. Begin with the ignition off. Then pull the turn signal/multifunction lever toward you and hold it there while you perform the next step. 2. Turn the key to RUN and LOCK twice. Then, with the key in LOCK, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30-second program timer will begin. 3. You are now ready to program the automatic door locks. Select one of the four programming options listed above, and press the unlock side of the power door lock switch to cycle through the unlocking options. You will have 30 seconds to begin programming. If you exceed the 30-second limit, the locks will automatically lock and unlock and the horn will chirp twice to indicate that you have left the program mode. If this occurs, repeat the procedure beginning with Step 1 to re-enter the programming mode. You can exit the program mode any time by turning the ignition to RUN. The locks will automatically lock and unlock and the horn will chirp twice to indicate that you are leaving the program mode. If the lock/unlock switches are not pressed while in the programming mode, the current auto lock/unlock setting will not be modiﬁed. See your dealer for more information. 2-10 Rear Door Security Locks Your vehicle may have this feature. You can lock the rear doors so they cannot be opened from the inside by passengers. To use one of these locks do the following: 1. Open one of the rear doors. You will ﬁnd a security lock lever located on the inside edge of each rear door. 2. Move the lever down to engage the security lock. Move the lever up to disengage the security lock. 3. Close the door. The rear doors of your vehicle cannot be opened from the inside while this feature is in use. If you want to open the rear door while the security lock is on, unlock the door and open the door from the outside. Lockout Protection This feature stops the power door locks from locking when the key is in the ignition and a door is open to protect you from locking your key in the vehicle. If the power lock switch is pressed when a door is open and the key is in the ignition, all the doors will lock and then the driver’s door will unlock. Liftgate/Liftglass {CAUTION: It can be dangerous to drive with the liftgate or liftglass open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. CAUTION: (Continued) CAUTION: (Continued) If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate or liftglass: (cid:127) Make sure all other windows are shut. (cid:127) Turn the fan on your climate control system to its highest speed and select the control setting that will force outside air into your vehicle. See “Climate Control System” in the Index. (cid:127) If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 2-36. Liftgate Release To unlock the liftgate, use the power door lock switch or the remote keyless entry transmitter. See Remote Keyless Entry (RKE) System Operation on page 2-5. The liftglass will also unlock when the liftgate is unlocked. Press the button on the liftglass to open it. To open the entire liftgate, lift the handle located in the center of the liftgate. When the liftgate is opened, the liftglass will lock after a short delay. 2-11 Emergency Release for Opening Liftgate 1. Remove the trim plug, located on the inside of the liftgate in the center, to expose the access hole in the trim panel. 2. Use a tool to reach through the access hole in the trim panel. 3. Pry the left release lever up to the unlock position. Pry the right release lever up to unlatch the liftgate. 4. Reinstall the trim plug. Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 2-12 Power Windows {CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window. Do not leave keys in a vehicle with children. When there are children in the rear seat use the window lockout button to prevent unintentional operation of the windows. The controls for the power windows are located on the armrest on each of the side doors. With power windows, the switches operate the windows when the ignition is in RUN, ACCESSORY or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-21. The driver’s door also has a switch for each of the passenger’s windows. Press down the top of the switch to lower the window and pull up on the switch to raise the window. If you hold the switch down for three to seven seconds after the window has been completely lowered or raised, the window will not operate for about 15 seconds. 2-13 Express-Down Window AUTO (Express-down): The driver’s and front passenger’s window switches have an express-down feature that allows you to lower the window without holding the switch down. Press down brieﬂy on the driver’s or front passenger’s window switch labeled AUTO to activate the express-down feature. Lightly tap the switch to open the window slightly. The express-down feature can be interrupted at any time by pressing the top of the switch. Window Lockout o (Lockout): Your vehicle has a lockout feature to prevent passengers from operating the power windows. The lockout switch is located in front of the window switches on the driver’s door. A light in the lockout switch will come on to show that the switch has been activated. Press the lockout switch again to return to normal operation. Sun Visors Sun Visors with Slide Rod Your vehicle may have this feature. Pull the sun visor down to block glare. Detach the sun visor from the center mount and slide it along the rod from side-to-side to cover the driver or passenger side of the front window. Swing the sun visor to the side to cover the side window. It can also be moved along the rod from side-to-side in this position. Sun Visors with Fixed Rod and Pull-out Extension Your vehicle may have this feature. Pull the sun visor down to block glare. Pull the sun visor extender out for additional coverage. Detach the sun visor from the center mount and swing it to the side to cover the side window. Visor Vanity Mirror Pull the sun visor down to expose the vanity mirror. You may have to lift a cover to expose the mirror. Lighted Visor Vanity Mirror Your vehicle may have this feature. Pull the sun visor down and lift the mirror cover to turn on the lamps. The lamps will turn off when the cover is closed. 2-14 Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Your vehicle has theft-deterrent features, however, they do not make it impossible to steal. Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system. The security light is located on the instrument panel cluster. To operate the system: 1. Open the door. 2. Lock the door with the power door lock switch or the Remote Keyless Entry (RKE) transmitter. The security light should ﬂash. The system will not activate if the doors are locked with the key or manual door lock. 3. Close all doors. The security light should turn off after about 30 seconds. The alarm is not armed until the security light turns off. If a locked door is opened without the key or the RKE transmitter, the alarm will go off. The headlamps and parking lamps will ﬂash for two minutes, and the horn will sound for 30 seconds, then will turn off to save the battery power. To avoid setting off the alarm by accident: (cid:127) Always lock the vehicle using the door key after the doors are closed. (cid:127) Always unlock a door with a key, or use the RKE transmitter. Unlocking a door any other way will set off the alarm. To turn off the alarm, press unlock on the RKE transmitter or unlock any door with the key. 2-15 Testing the Alarm To test the alarm: 1. From inside the vehicle, lower the driver’s window and open the driver’s door. 2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the RKE transmitter. 3. Get out of the vehicle, close the door and wait for the security light to go out. 4. Then reach in through the window, unlock the door with the manual door lock and open the door. This should set off the alarm. When the alarm is set the power door unlock switch will not work. If the alarm does not sound when it should but the headlamps ﬂash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers on page 5-110. If the alarm does not sound or the headlamps do not ﬂash, the vehicle should be serviced by your dealer/retailer. 2-16 Passlock® (U. S. Only) Your vehicle has the Passlock theft-deterrent system. Passlock is a passive theft-deterrent system that enables fuel if the ignition lock cylinder is turned with a valid key. If a correct key is not used or the ignition lock cylinder has been tampered with, the fuel system is disabled and the vehicle will not start. During normal operation, the security light will turn off about ﬁve seconds after the key is turned to ON/RUN. If the engine stalls and the security light ﬂashes, wait about 10 minutes until the light stops ﬂashing before trying to restart the engine. Remember to release the key from START as soon as the engine starts. If the engine does not start after three tries, the vehicle needs service. If the engine is running and the security light comes on, you will be able to restart the engine if you turn the engine off. However, your Passlock system is not working properly and must be serviced by your dealer/retailer. Your vehicle is not protected by Passlock at this time. You may also want to check the fuse. See Fuses and Circuit Breakers on page 5-110. See your dealer/retailer for service. In an emergency, call the Roadside Assistance Center. See Roadside Assistance Program on page 7-7. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle. PASS-Key® III+ Electronic Immobilizer The PASS-Key® III+ system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. PASS-Key® III+ uses a radio frequency transponder in the key that matches a decoder in your vehicle. PASS-Key® III+ Electronic Immobilizer Operation (Canada Only) Your vehicle has a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. The system is automatically disarmed when the key is turned to ON/RUN. You do not have to manually arm or disarm the system. The security light will come on if there is a problem with arming or disarming the theft-deterrent system. The key uses a transponder that matches an immobilizer control unit in your vehicle. Only the correct key will start the vehicle. If the key is ever damaged, you may not be able to start your vehicle. When trying to start the vehicle, if the engine does not start and the security light comes on, there may be a problem with your theft-deterrent system. Turn the ignition off and try again. 2-17 If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse. See Fuses and Circuit Breakers on page 5-110. If the engine still does not start with the other key, your vehicle needs service. If your vehicle does start, the ﬁrst key may be faulty. See your dealer/retailer who can service the theft-deterrent system and have a new key made. It is possible for the theft-deterrent system decoder to learn the transponder value of a new or replacement key. Up to 10 keys may be programmed for the vehicle. The following procedure is for programming additional keys only. Canadian Owners: If you lose or damage your keys, only a dealer/retailer can service the theft-deterrent system to have new keys made. To program additional keys you will require two current driver’s keys. To program a new key do the following: 1. Verify that the new key has PK3+ stamped on it. 2. Insert the current driver’s key in the ignition and start the engine. If the engine will not start see your dealer/retailer for service. 3. After the engine has started, turn the key to LOCK/OFF, and remove the key. 4. Insert the second current driver’s key in the ignition and start the engine within ten seconds of removing the previous key. If the engine will not start see your dealer/retailer for service. 5. After the engine has started, turn the key to LOCK/OFF, and remove the key. Insert the key to be programmed and turn it to ON within ten seconds of removing the previous key. The security light will turn off once the key has been programmed. 6. Repeat the Steps 1 through 5 if additional keys are to be programmed. If the security light comes on and stays on while driving, you will be able to restart the engine if you turn it off. The theft-deterrent system, however, is not working properly and must be serviced by your dealer/retailer. Your vehicle is not protected by the theft-deterrent system at this time. In an emergency, contact Roadside Assistance. See Roadside Assistance Program on page 7-7. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle. 2-18 Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:127) Keep your speed at 55 mph (88 km/h) or less for the ﬁrst 500 miles (805 km). (cid:127) Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. Avoid downshifting to brake or slow the vehicle. (cid:127) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time the new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:127) Do not tow a trailer during break-in. See Towing a Trailer on page 4-48 for the trailer towing capabilities of your vehicle and more information. Following break-in, engine speed and load can be gradually increased. 2-19 Ignition Positions Use the key to turn the ignition switch to four different positions. Press the regular brake pedal, and turn the ignition to ON/RUN to shift out of PARK (P). Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is all the way in. If none of this works, then your vehicle needs service. A (LOCK/OFF): This position locks the ignition and transmission. It is a theft-deterrent feature. You will only be able to remove the key when the ignition is turned to LOCK/OFF. 2-20 If the steering wheel is locked, move it from right to left and turn the key to ACC/ACCESSORY. If none of this works, then your vehicle needs service. B (ACC/ACCESSORY): This position lets you use things like the radio and the windshield wipers when the engine is off. Lengthy operation of features such as the radio in the ACC/ACCESSORY may drain the battery and prevent your vehicle from starting. Do not operate your vehicle in the ACC/ACCESSORY for a long period of time. C (ON/RUN): This is the position for driving. The battery could be drained if you leave the key in the ACC/ACCESSORY or ON/RUN position with the engine off. You may not be able to start your vehicle if the battery is allowed to drain for an extended period of time. D (START): This position starts the engine. Key In the Ignition Never leave your vehicle with the keys inside. If you leave the key in the ignition and park your vehicle, a chime will sound when you open the driver’s door. Remember to remove your key from the ignition and take it with you. This will lock your ignition and transmission. Also, always remember to lock the doors. The battery could be drained if you leave the key in the ignition while your vehicle is parked. You may not be able to start your vehicle after it has been parked for an extended period of time. Retained Accessory Power (RAP) These vehicle accessories can be used for up to 20 minutes after the engine is turned off: (cid:127) Audio System (cid:127) Power Windows (cid:127) Overhead Console (cid:127) Sunroof (if equipped) These features will work when the key is in ON/RUN or ACC/ACCESSORY. Once the key is turned from ON/RUN to LOCK/OFF, these features continue to work for up to 20 minutes, or until a door is opened. Starting the Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position – this is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Do not try to shift to PARK (P) if your vehicle is moving. If you do, you could damage the transmission. Shift to PARK (P) only when your vehicle is stopped. Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Do not race the engine immediately after starting it. Operate the engine and transmission gently to allow the oil to warm up and lubricate all moving parts. Your vehicle has a Computer-Controlled Cranking System. This feature assists in starting the engine and protects components. If the ignition key is turned to the START position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. 2-21 If the engine does not start and the key is held in START for many seconds, cranking will be stopped after 15 seconds to prevent cranking motor damage. To prevent gear damage, this system also prevents cranking if the engine is already running. Engine cranking can be stopped by turning the ignition switch to the ACC/ACCESSORY or LOCK/OFF position. Notice: Cranking the engine for long periods of time, by returning the key to the START position immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to let the cranking motor cool down. 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be ﬂooded with too much gasoline. Try pushing the accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go of the key and accelerator. If the vehicle starts brieﬂy but then stops again, do the same thing. This clears the extra gasoline from the engine. Do not race the engine immediately after starting it. Operate the engine and transmission gently until the oil warms up and lubricates all moving parts. Notice: The engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer/retailer. If you do not, your engine might not perform properly. Any resulting damage would not be covered by your vehicle’s warranty. Adjustable Throttle and Brake Pedal If your vehicle has this feature, you can change the position of the throttle and brake pedals. This feature is designed for shorter drivers, since the pedals cannot move farther away from the standard position, but can move closer for better pedal reach. The vehicle must be in PARK (P) for this feature to operate. 2-22 The switch used to adjust the pedals is located on the steering column. Press the switch forward or backward to move the pedals closer or farther away from you. Engine Coolant Heater The engine coolant heater, if available, can help in cold weather conditions at or below 0°F (−18°C) for easier starting and better fuel economy during engine warm-up. Plug in the coolant heater at least four hours before starting your vehicle. An internal thermostat in the plug-end of the cord may exist which will prevent engine coolant heater operation at temperatures above 0°F (−18°C). To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located on the driver’s side of the engine compartment next to the battery box facing the engine. 3. Plug it into a normal, grounded 110-Volt AC outlet. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. 2-23 How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you will be parking your vehicle. The dealer/retailer can give you the best advice for that particular area. Active Fuel Management™ Your vehicle’s V8 engine may have Active Fuel Management™. This system allows the engine to operate on either all or half of its cylinders, depending on your driving conditions. When less power is required, such as cruising at a constant vehicle speed, the system will operate in the half cylinder mode, allowing your vehicle to achieve better fuel economy. When greater power demands are required, such as accelerating from a stop, passing, or merging onto a freeway, the system will maintain full-cylinder operation. Automatic Transmission Operation There are several different positions for your gear shift lever. PARK (P): This position locks the rear wheels. It is the best position to use when you start the engine because your vehicle cannot move easily. 2-24 {CAUTION: {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into PARK (P) on page 2-33. If you are pulling a trailer, see Towing a Trailer on page 4-48. If you have four-wheel drive, your vehicle will be free to roll — even if your shift lever is in PARK (P) — if your transfer case is in NEUTRAL. So, be sure the transfer case is in a drive gear — not in NEUTRAL. See Four-Wheel Drive on page 2-28. See Shifting Into PARK (P) on page 2-33. Make sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transmission shift lock control system. You have to fully apply the regular brakes ﬁrst and then press the shift lever button before you can shift from PARK (P) when the ignition key is in ON/RUN. If you cannot shift out of PARK (P), ease pressure on the shift lever and push the shift lever all the way into PARK (P) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of PARK (P) on page 2-35. 2-25 REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice, or sand without damaging your transmission, see If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 4-33. NEUTRAL (N): In this position, the engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. {CAUTION: Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) with the engine running at high speed may damage the transmission. The repairs would not be covered by your warranty. Be sure the engine is not running at high speed when shifting your vehicle. DRIVE (D): This position is for normal driving. It provides the best fuel economy for your vehicle. If you need more power for passing, and you are: (cid:127) Going less than about 35 mph (55 km/h), push the accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h) or more, push the accelerator all the way down. You will shift down to the next gear and have more power. Downshifting the transmission in slippery road conditions could result in skidding, see “Skidding” under Loss of Control on page 4-12. DRIVE (D) can be used when towing a trailer, carrying a heavy load, driving on steep hills, or for off-road driving. You may want to shift the transmission to THIRD (3) or, if necessary, a lower gear selection if the transmission shifts too often. 2-26 THIRD (3): This position is also used for normal driving. It reduces vehicle speed more than DRIVE (D) without using your brakes. You might choose THIRD (3) instead of DRIVE (D) when driving on hilly, winding roads, when towing a trailer, so there is less shifting between gears and when going down a steep hill. FIRST (1): This position reduces vehicle speed even more than SECOND (2) without using your brakes. You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in FIRST (1) while the vehicle is moving forward, the transmission will not shift into ﬁrst gear until the vehicle is going slowly enough. To shift to the THIRD (3) position, you must ﬁrst press the large button on the shift handle. While the button is pressed, move the shifter in the THIRD (3) position. SECOND (2): This position reduces vehicle speed even more than THIRD (3) without using your brakes. You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. To shift to the SECOND (2) position, you must ﬁrst press the large button on the shift handle. While the button is pressed, move the shifter in the SECOND (2) position. You can also use SECOND (2) for starting the vehicle from a stop on slippery road surfaces. To shift to the FIRST (1) position, you must ﬁrst press the large button on the shift handle. While the button is pressed, move the shifter in the FIRST (1) position. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will not be covered by your warranty. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. 2-27 Four-Wheel Drive If your vehicle has four-wheel drive, the engine’s driving power can be sent to all four wheels for extra traction. To get the most satisfaction out of four-wheel drive, you must be familiar with its operation. Read the part that follows before using four-wheel drive. You should use Two-Wheel High for most normal driving conditions. Notice: Driving on clean, dry pavement in Four-Wheel-Drive High or Four-Wheel-Drive Low for an extended period of time may cause premature wear on your vehicle’s powertrain. Do not drive on clean, dry pavement in Four-Wheel-Drive High or Four-Wheel-Drive Low for extended periods of time. Notice: the transfer case in AUTO or Four-Wheel Drive, you could shorten the life of the transfer case or the Four-Wheel Drive system. The selector switch should be left in Two-Wheel Drive High mode. Only use AUTO and Four-Wheel Drive when you need extra traction such as in wet or slippery road conditions. If you continually drive your vehicle with 2-28 Automatic Transfer Case If your vehicle has four-wheel drive, the transfer case knob is located to the right of the steering wheel on the instrument panel. Use this knob to shift into and out of four-wheel drive 2 m (Two-Wheel High): This setting is for driving in most street and highway situations. Your front axle is not engaged in two-wheel drive. It also provides the best fuel economy. AUTO (Automatic Four-Wheel Drive): This setting is ideal for use when road conditions are variable. When driving your vehicle in automatic four-wheel drive, the front axle is engaged, but the vehicle’s power is sent to the rear wheels. When the vehicle senses a loss of traction, the system will automatically engage four-wheel drive. Driving in this mode results in slightly lower fuel economy than Two-Wheel High. 4 m (Four-Wheel High): This setting should be used when you need extra traction, such as on snowy or icy roads or in most off-road situations. This setting also engages your front axle to help drive your vehicle. 4 n (Four-Wheel Low): This setting also engages your front axle and delivers extra torque. It sends maximum power to all four wheels. You might choose this setting if you are driving off-road in deep sand, deep mud, and climbing or descending steep hills. {CAUTION: Shifting the transfer case to NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in NEUTRAL. See Parking Brake on page 2-32. NEUTRAL: Shift the vehicle’s transfer case to NEUTRAL only when towing your vehicle. See Recreational Vehicle Towing on page 4-42 for more information. An indicator light in the knob will show you which position the transfer case is in. The indicator lights will come on brieﬂy when you turn on the ignition and one will stay on. If the lights do not come on, you should take your vehicle to your dealer for service. An indicator light will ﬂash while shifting the transfer case. It will stay on when the shift is complete. If for some reason the transfer case cannot make a requested shift, it will return to the last chosen setting. If the service Four-Wheel Drive Warning Light on the instrument panel cluster stays on, you should take your vehicle to your dealer for service. See Service Four-Wheel Drive Warning Light on page 3-47 for further information. Shifting Into Four-Wheel High or Automatic Four-Wheel Drive Turn the knob to Four-Wheel High or Automatic Four-Wheel Drive. This can be done at any speed unless you are shifting out of Four-Wheel Low. The indicator light will ﬂash while shifting. It will remain on when the shift is complete. 2-29 Shifting Into Two-Wheel High Turn the knob to Two-Wheel High. This can be done at any speed unless you are shifting out of Four-Wheel Low. Shifting Into Four-Wheel Low To shift to Four-Wheel Low, the vehicle’s engine must be running and the vehicle must be stopped or moving less than 2 mph (3.2 km/h) with the transmission in NEUTRAL (N). The preferred method for shifting into Four-Wheel Low is to have your vehicle moving 1 or 2 mph (1.6 to 3.2 km/h). Turn the knob to Four-Wheel Low. You must wait for the Four-Wheel Low indicator light to stop ﬂashing and stay on before shifting the transmission into gear. If you turn the knob to Four-Wheel Low when your vehicle is in gear and/or moving, the Four-Wheel Low indicator light will ﬂash for 30 seconds and not complete the shift unless your vehicle is moving less than 2 mph (3.2 km/h) and the transmission is in NEUTRAL (N). After 30 seconds, the transfer case will return to the setting last chosen. Shifting Out of Four-Wheel Low To shift from Four-Wheel Low to Four-Wheel High, Auto Four-Wheel Drive, or Two-Wheel High, your vehicle must be stopped or moving less than 2 mph (3.2 km/h) with the transmission in NEUTRAL (N) and the engine running. The preferred method for shifting out of Four-Wheel Low is to have your vehicle moving 1 or 2 mph (1.6 to 3.2 km/h). Turn the knob to Four-Wheel High, Auto Four-Wheel Drive, or Two-Wheel High. You must wait for the Four-Wheel High, Auto Four-Wheel Drive, or Two-Wheel High indicator light to stop ﬂashing and stay off before shifting your transmission into gear. If the knob is turned to Four Wheel-High, Auto Four-Wheel Drive, or Two-Wheel High when your vehicle is in gear and/or moving, the Four-Wheel High, Auto Four-Wheel Drive, or Two-Wheel High indicator light will ﬂash for 30 seconds. It will not complete the shift unless your vehicle is moving less than 2 mph (3.2 km/h) with the transmission in NEUTRAL (N). 2-30 Shifting into NEUTRAL Before shifting the transfer case to NEUTRAL, ﬁrst make sure the vehicle is parked so that it will not roll. 1. Set the parking brake. 2. Start the vehicle. 3. Put the transmission in NEUTRAL (N). 4. Shift the transfer case to Two-Wheel High. 5. Turn the transfer case knob all of the way past Four-Wheel Low and hold it there for a minimum of 10 seconds. The neutral indicator light will come on. 6. With the engine running, shift the transmission to REVERSE (R) for one second, then shift the transmission to DRIVE (D) for one second, to ensure that the transfer case is in NEUTRAL. 7. Turn the engine off, by turning the key to ACC/ACCESSORY. 8. Place the transmission shift lever in PARK (P). 9. Turn the ignition to LOCK/OFF. Shifting Out of NEUTRAL To shift the transfer case out of NEUTRAL, do the following: 1. Set the parking brake and apply the regular brake pedal. 2. Turn the ignition to ON/RUN with the engine off. 3. Put the transmission in NEUTRAL (N). 4. Turn the transfer case knob to the desired position (Two-Wheel High, Four-Wheel High, or Auto Four-Wheel Drive). 5. After the transfer case has shifted out of NEUTRAL, the indicator light will go out. 6. Release the parking brake. 7. Start the engine and shift the transmission to the desired position. 2-31 Parking Brake To set the parking brake, hold the regular brake pedal down with your foot and pull up on the parking brake lever located between the seats. To release the parking brake, hold the regular brake pedal down. Pull the parking brake lever up until you can press in the button at the end of the lever. Hold the button in as you move the parking brake lever all the way down. If the ignition is on, the brake system warning light on the instrument panel cluster will come on. See Brake System Warning Light on page 3-38. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and you must park on a hill, see Towing a Trailer on page 4-48. 2-32 To shift into PARK (P): 1. Hold the brake pedal down with your foot and set the parking brake. 2. Move the shift lever into PARK (P) by pressing the button on the side of the shift lever and pushing the lever all the way toward the front of the vehicle. 3. Turn the ignition key to OFF/LOCK. 4. Remove the key and take it with you. You know your vehicle is in PARK (P) if the key can be removed from the ignition. Shifting Into PARK (P) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. With four-wheel drive, your vehicle will be free to roll — even if your shift lever is in PARK (P) — if your transfer case is in NEUTRAL. So, be sure the transfer case is in a drive gear — not in NEUTRAL. See Four-Wheel Drive on page 2-28. Always put the shift lever fully in PARK (P) with the parking brake ﬁrmly set. If you are pulling a trailer, see Towing a Trailer on page 4-48. 2-33 Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. If you have four-wheel drive, your vehicle will be free to roll – even if your lever is in PARK (P) – if your transfer case is in NEUTRAL. So be sure the transfer case is in a drive gear – not NEUTRAL. See Four-Wheel Drive on page 2-28. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running unless you have to. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pressing the button on the console shift lever. If you can, it means that the shift lever was not fully locked into PARK (P). Torque Lock If you are parking on a hill and you do not shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into PARK (P) on page 2-33. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of PARK (P). 2-34 Shifting Out of PARK (P) This vehicle has an electronic shift lock release system. The shift lock release is designed to: (cid:127) Prevent ignition key removal unless the shift lever is in PARK (P) with the shift lever button fully released, and (cid:127) Prevent movement of the shift lever out of PARK (P), unless the ignition is in ON/RUN and the regular brake pedal is applied. The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9 volt) battery. If your vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 5-44 for more information. To shift out of PARK (P) use the following: 1. Apply the brake pedal. 2. Press the shift lever button. 3. Move the shift lever to the desired position. If you still are unable to shift out of PARK (P): 1. Fully release the shift lever button. 2. Hold the brake pedal down and press the shift lever button again. 3. Move the shift lever to the desired position. If you still cannot move the shift lever from PARK (P), consult your dealer/retailer or a professional towing service. Parking Over Things That Burn {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. 2-35 Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-36. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Also see “If You Are Caught in a Blizzard” under Winter Driving on page 4-29. Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) The exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or the exhaust system has been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. 2-36 Follow the proper steps to be sure your vehicle will not move. See Shifting Into PARK (P) on page 2-33. If you are pulling a trailer, see Towing a Trailer on page 4-48. Mirrors Manual Rearview Mirror When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from the lamps behind you. Move the lever to the right for nighttime use and to the left for daytime use. {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to PARK (P). {CAUTION: If your vehicle has four-wheel drive, it will be free to roll — even if the shift lever is in PARK (P) — if the transfer case is in NEUTRAL. So be sure the transfer case is in a drive gear — not in NEUTRAL. See Four-Wheel Drive on page 2-28. 2-37 Manual Rearview Mirror with OnStar® When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from the lamps behind you. Move the lever to the right for nighttime use and to the left for daytime use. There may also be three OnStar® buttons located at the bottom of the mirror face. See your dealer/retailer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-47 for more information on the services OnStar® provides. Automatic Dimming Rearview Mirror with OnStar® and Compass Your vehicle may have an automatic-dimming rearview mirror with a compass. There may be three additional buttons for the OnStar® system. See your dealer/retailer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-47 for more information about the services OnStar® provides. O (On/Off): This is the on/off button. 2-38 Automatic Dimming Mirror Operation The automatic dimming mirror comes on each time the ignition is turned to start. To turn the automatic dimming feature off or back on, press the on/off button. The indicator light on the mirror is lit when the automatic dimming feature is on. Compass Operation Press the on/off button once to turn the compass on or off. There is a compass display in the window in the upper right corner of the mirror face. Compass Calibration Press and hold the on/off button to activate the compass calibration mode. CAL will be displayed in the compass window on the mirror. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. If after a few seconds the display does not show a compass direction, (N for North for example), there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, note pad holder, or similar object. If the letter C or CAL appears in the compass window, the compass may need to be reset or calibrated. Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. The mirror is set to zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as during a long distance cross-country trip, it will be necessary to adjust for compass variance. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the on/off button until the zone number is displayed. The number shown is the current zone number. 3. Scroll through the zone numbers that appear in the window on the mirror by pressing the on/off button. Once you ﬁnd your zone number, release the button. After about four seconds, the mirror will return to the compass display, and the new zone number will be set. If C or CAL appears in the compass window, the compass may need calibration. See “Compass Calibration” listed previously. 2-39 Temperature and Compass Display Press the on/off button, located to the far left, brieﬂy to turn the compass/temperature display on or off. If the display reads CAL, you will need to calibrate the compass. For more information on calibration, see below. To adjust between Fahrenheit and Celsius, do the following: 1. Press and hold the on/off button until either a ﬂashing F or C appears. 2. Press the button again to change the display to the desired unit of measurement. After approximately four seconds of inactivity, the new unit will be locked in and the display will return. If an abnormal temperature reading is displayed for an extended period of time, please consult your dealer. Under certain circumstances, a delay in updating the temperature is normal. Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display Your vehicle may have this feature. When on, an automatic dimming mirror automatically dims to the proper level to minimize glare from lights behind you after dark. The mirror also includes a dual display in the upper right corner of the mirror face. The compass reading and the outside temperature will both appear in the display at the same time. P (On/Off): This is the on/off button. Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror, do the following: 1. Make sure the green indicator light, located to the left of the on/off button, is lit. If it’s not, press and hold the on/off button until the green light comes on, indicating that the mirror is in automatic dimming mode. 2. Turn off the automatic dimming mirror function by pressing and holding the on/off button until the green indicator light turns off. 2-40 Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the on/off button until a Z and a zone number appear in the display. The compass is now in zone mode. 3. Keep pressing the on/off button until the desired zone number appears in the display. Release the button. After approximately four seconds of inactivity, the new zone number will be locked in and the compass/temperature display will return. 4. Calibrate the compass as described next. 2-41 Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Automatic Dimming Rearview Mirror with Compass and Temperature Display If the vehicle is equipped with an automatic mirror, it will, when on, automatically dim to the proper level to minimize glare from lights behind you after dark. The mirror also includes a display in the upper right corner of the mirror face. The compass reading and the outside temperature will both appear in the display at the same time. The dual display can be turned on or off by brieﬂy pressing either the TEMP or the COMP button. Compass Calibration The compass may need calibration if one of the following occurs: (cid:127) After approximately ﬁve seconds, the display does not show a compass heading (N for North, for example), there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder or a similar magnetic item. (cid:127) The compass does not display the correct heading and the compass zone variance is set correctly. In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, press and hold the on/off button until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Passenger Airbag Indicator The vehicle may be equipped with a passenger airbag indicator, on the mirror glass, just above the buttons. If the vehicle has this feature, the mirror will display the word ON, or an airbag symbol in Canada, when the passenger airbag is enabled. For more information, see Passenger Sensing System on page 1-60. 2-42 Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror, do the following: 1. Make sure the green indicator light, located to the left of the on/off button, is lit. If it’s not, press and hold the on/off button until the green light comes on, indicating that the mirror is in automatic dimming mode. 2. Turn off the automatic dimming mirror function by pressing and holding the on/off button until the green indicator light turns off. Temperature Display The temperature can be displayed by pressing the TEMP button. Pressing the TEMP button once brieﬂy, will toggle the temperature reading on and off. To alternate the temperature reading between Fahrenheit and Celsius, press and hold the TEMP button until the display blinks F and C. Press and release the TEMP button to toggle between the Fahrenheit and Celsius readings. After approximately four seconds of inactivity, the display will stop blinking and display the last selection made. If an abnormal reading is displayed, for an extended period of time, please consult your dealer. Under certain circumstances, a delay in updating the temperature is normal. Compass Operation Press the COMP button once brieﬂy to turn the compass on or off. When the ignition and the compass feature are on, the compass will show two character boxes for approximately two seconds. After two seconds, the mirror will display the compass heading. Compass Calibration The compass may need calibration if one of the following occurs: (cid:127) If CAL is displayed while driving in the vehicle. (cid:127) After approximately ﬁve seconds, the display does not show a compass heading (N for North, for example), there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder or a similar magnetic item. (cid:127) The compass does not display the correct heading and the compass zone variance is set correctly. In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, press and hold the COMP button until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. 2-43 Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the following zone map. 2-44 2. Press and hold the COMP button until a zone number appears in the display. 3. Press the COMP button on the bottom of the mirror until the new zone number appears in the display. After you stop pressing the button, the display will show a compass direction within a few seconds. Passenger Airbag Indicator The mirror may be equipped with a passenger airbag indicator on the mirror glass, just above the buttons. If the vehicle has this feature the mirror will display the word ON, or an airbag symbol in Canada, when the passenger airbag is enabled. For more information see Passenger Sensing System on page 1-60. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Outside Manual Mirrors Adjust the outside rearview mirrors so you can see a little of the side of your vehicle, and the area beside your vehicle from a comfortable driving position. The mirrors can be folded in to enter narrow areas. Return the mirrors to the unfolded position before driving. Outside Power Mirrors Your vehicle may have this feature. The power mirror control is located on the driver’s door. Turn the control knob left or right to select the desired mirror. Then move the control knob to the left or right or up or down to position the mirror so that you can see a little of the outside of the vehicle. After adjusting the position of the mirrors, turn the knob to the center off position so that the mirrors do not move. If the travel position in any direction of the mirror is reached, it will enter a ratcheting mode. This action is harmless. It is a warning that the mirror can go no further. To stop this action, back the mirror up by moving the knob in the opposite direction. The mirrors can be manually folded inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. To return the mirror to its original position, push outward. Be sure to return both mirrors to their original unfolded position before driving. 2-45 The passenger side mirror is convex shaped. A convex mirror’s surface is curved so more can be seen from the driver seat. It also makes things, like other vehicles, look farther away than they really are. Outside Heated Mirrors If the vehicle has this feature, when the rear window defogger is turned on, the outside driver’s and passenger’s rearview mirrors also heat to help clear them of ice, snow, and condensation. See Dual Climate Control System on page 3-21 or Dual Automatic Climate Control System on page 3-24 for more information. Outside Curb View Assist Mirror If the vehicle has this feature, the passenger’s outside mirror will adjust to a preset tilt position while the vehicle is in REVERSE (R) gear. Curb view assist may be useful when you are parallel parking. The mirror will return to normal position when the vehicle is shifted out of REVERSE (R) gear. Automatic mirror movement in either direction will follow a short delay. You may be able to turn this feature on or off through the Driver Information Center (DIC). See DIC Vehicle Customization on page 3-58. Outside Convex Mirror {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. 2-46 OnStar® System OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar button and they can contact Roadside Service for you. OnStar service is provided to you subject to the OnStar Terms and Conditions. You may cancel your OnStar service at any time by contacting OnStar. A complete OnStar Owner’s Guide and the OnStar Terms and Conditions are included in the vehicle’s OnStar Subscriber glove box literature. For more information, visit onstar.com or onstar.ca, contact OnStar at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar button to speak with an OnStar advisor 24 hours a day, 7 days a week. Not all OnStar features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar services and system limitations, see the OnStar Owner’s Guide in your glove box or visit onstar.com. OnStar Services For new vehicles with OnStar, the Safe & Sound Plan, or the Directions & Connections Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions & Connections Plan. For more information, press the OnStar button to speak with an advisor. Some OnStar services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar. 2-47 Available Services with Safe & Sound Plan (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) (cid:127) Link to Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Location Assistance (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) OnStar Vehicle Diagnostics (cid:127) GM Goodwrench On Demand Diagnostics (cid:127) OnStar Hands-Free Calling with 30 complimentary minutes (cid:127) OnStar Virtual Advisor (U.S. Only) Available Services included with Directions & Connections Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions - Advisor delivered or OnStar Turn-by-Turn Navigation (If equipped) (cid:127) RideAssist (cid:127) Information and Convenience Services OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To ﬁnd out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). 2-48 OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar Owner’s Guide for more information (Only available in the continental U.S.). OnStar Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-105 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” to activate the OnStar Hands-Free Calling. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar Owner’s Guide for more information. How OnStar Service Works Your vehicle’s OnStar system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar Call Center at the time of an OnStar button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar Hands-Free Calling, your vehicle also sends OnStar your GPS location so that we can provide you with location-based services. OnStar service cannot work unless your vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless you are in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. Location information about your vehicle is only available if the GPS satellite signals are unobstructed and available. 2-49 Your vehicle must have a working electrical system (including adequate battery power) for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility Increase the radio volume if you cannot hear the OnStar advisor. If the light next to the OnStar buttons is red, this means that your system is not functioning properly and should be checked by your dealer/retailer. If the light appears clear (no light is appearing), your OnStar subscription has expired. You can always press the OnStar button to conﬁrm that your OnStar equipment is active. Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. 2-50 Universal Home Remote System Operation (With One Triangular LED) If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming the Universal Home Remote. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate you are programming. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming the Universal Home Remote System If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. 2-51 To program up to three devices: 1. From inside the vehicle, press and hold down the two outside buttons at the same time, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. This step will erase the factory settings or all previously programmed buttons. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons. 2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit). 2-52 3. At the same time, press and hold both the Universal Home Remote button that you would like to use to control the garage door and the hand-held transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 4. The indicator light on the Universal Home Remote will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on continuously, the programming is complete and your garage door should move when the Universal Home Remote button is pressed and released. You do not need to continue the programming Steps 6 through 8 and can stop here. If the Universal Home Remote indicator light blinks rapidly for two seconds and then turns to a constant light, continue with the programming Steps 6 through 8. It may be helpful to have another person available to assist with the remaining steps. 6. After Steps 1 through 5 have been completed, locate inside the garage the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. 7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8. 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move, press and hold the same button a third time for two seconds, and then release. The Universal Home Remote should now activate the garage door. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming the Universal Home Remote System.” Do not repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. 2-53 Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. 2-54 Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons Erase the programmed buttons when you sell or terminate your lease. To erase all programmed buttons on the Universal Home Remote device: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. 2. Release both buttons. Reprogramming a Single Universal Home Remote Button To reprogram any of the three Universal Home Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 7-5. Storage Areas Glove Box To open, lift the handle up. Use the key to lock and unlock. Overhead Console Your vehicle may have this feature. The overhead console may include reading lamps, a Universal Home Remote and a sunroof switch. See Sunroof on page 2-58 and Universal Home Remote System on page 2-50 for more information. Center Console Storage Pull the front lever on the center console while lifting the top to open it. The console has cupholders on the front and rear of the storage compartment. The console may also contain: (cid:127) Rear Seat Audio Controls (cid:127) Rear Seat Accessory Power Outlets (cid:127) Rear Climate Control To open the center armrest compartment, lift the cover by pulling up on the latch handle located under the front edge of the armrest. 2-55 Luggage Carrier {CAUTION:

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2008 Chevrolet Trailblazer Owners Manual