2004 Chevrolet Tracker Owners Manual

of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

5-69

Wheel Replacement Replace any wheel that is bent, cracked or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle.

{CAUTION:

Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement.

Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance and tire or tire chain clearance to the body and chassis. See ChangingaFlatTireonpage5-72 for more information.

5-70

Used Replacement Wheels

{CAUTION:

Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.

Tire Chains Notice: Use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires. Install them on the tires of the drive axle (four-wheel-drive vehicles can use chains on both axles). Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.

5-71

If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop well out of the traffic lane. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you’d use in a skid. In any rear blowout, remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop, well off the road if possible.

{CAUTION:

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. Use the jack provided with your vehicle only for changing a flat tire.

If a tire goes flat, the next part shows how to use your jacking equipment to change a flat tire safely.

Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers.

5-72

{CAUTION:

CAUTION:

(Continued)

To be even more certain the vehicle won’t move, you can put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire on the other side, at the opposite end of the vehicle.

Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving:

1. Set the parking brake firmly. 2. Put an automatic transmission shift lever

in PARK (P), or shift a manual transmission to FIRST (1) or REVERSE (R).

3. If you have a four-wheel-drive vehicle, be sure the transfer case is in a drive gear — not in NEUTRAL.

4. Turn off the engine and do not restart

while the vehicle is raised.

5. Do not allow passengers to remain in the

vehicle.

CAUTION:

(Continued)

5-73

The following steps will tell you how to use the jack and change a tire. Removing the Spare Tire and Tools

2. Turn the jack screw to remove the jack from the clamps. If the screw is too tight, use the jack handle to loosen it.

The jack, wheel wrench and jack handle are stowed in the rear left corner of the luggage compartment. 1. To open the jacking tool storage compartment, turn

the knob counterclockwise. Open the cover two inches and pull the entire cover towards the front of the vehicle.

5-74

The tools you’ll be using include the jack (A), jack handle (B) and wheel wrench (C). The spare tire is mounted on your tailgate. Your vehicle may be equipped with either a soft, vinyl cover or a hard cover.

Hard Cover

3. To remove the hard cover from the spare tire, insert your key into the wheel lock and pull the wheel lock off.

5-75

4. Using the wheel wrench, remove the wheel cover nut. Gently pry the spare tire cover off the wheel.

Vinyl Cover

5. If your vehicle is equipped with a vinyl cover, unzip the cover to find the wheel lock. Insert the key into the wheel lock and pull it off.

6. Using the wheel wrench, remove the wheel nut

under the lock.

5-76

Removing the Flat Tire and Installing the Spare Tire

7. Remove the remaining wheel nuts with the wheel

wrench.

8. Remove the spare tire from the mounting bracket

and place it near your flat tire.

1. If your vehicle has wheel nut caps, remove them by

turning the wheel wrench counterclockwise.

5-77

2. Using the wheel wrench, loosen all the wheel nuts

but don’t remove them yet.

Front Wheel Location

5-78

Rear Wheel Location

3. Under the vehicle near each wheel, there are knobs

in the vehicle’s frame. Raise the jack two inches (51 mm) before positioning the jack. Raise the jack lift head until it fits firmly onto the knobs nearest to the flat tire.

{CAUTION:

Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

{CAUTION:

Raising your vehicle with the jack improperly positioned can cause personal injury and damage to the vehicle. If you try to use the jack when it hasn’t been raised at least two inches (51 mm), the jack may not hold up the vehicle, and you or others could be injured. To help avoid personal injury and vehicle damage, be sure to open the jack at least two inches (51 mm) before you fit the lift head into the proper location.

5-79

5. Remove all the wheel nuts and take off the flat tire.

4. Raise the vehicle by turning the jack handle

clockwise. Raise the vehicle far enough off the ground so there is enough room for the spare tire to fit underneath the wheel well.

5-80

6. Remove any rust or dirt

from the wheel bolts, mounting surfaces and spare wheel.

{CAUTION:

Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off.

{CAUTION:

Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident.

5-81

7. Place the spare on the wheel mounting surface. 8. Reinstall the wheel

nuts with the cone-shaped end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub.

5-82

9. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely.

10. Tighten the wheel nuts

firmly in a crisscross sequence as shown.

Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See “Capacities and Specifications” in the index for the wheel nut torque specification.

When you reinstall the full-size wheel and tire, you must also reinstall the plastic nut caps.

11. Tighten the plastic nut caps by hand. Then tighten them one half turn with the wheel wrench. Do not overtighten the nut caps or they may break.

{CAUTION:

Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification. See “Capacities and Specifications” in the Index for wheel nut torque specification.

5-83

Storing a Flat or Spare Tire and Tools

{CAUTION:

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

1. Store your vehicle’s flat or spare tire by mounting it

on the tailgate.

Notice: Ensure that the wheel balance weight is on the lower left section of the tire in order to allow proper installation of the spare wheel cover. 2. Put the top two wheel nuts back on with the wheel

wrench.

3. Put the spare tire cover back on, if equipped. Using the wheel wrench, put the wheel cover nut back on.

4. Put the spare wheel lock back on, if equipped and

lock it.

5. Put the jack, jack handle and wheel wrench back

into the storage area.

To stow the jack, place it in the storage bracket and turn the shaft clockwise until the jack is securely held in place. Reinstall the trim cover by inserting the cover tabs into the slots. Push the cover closed and turn the knob clockwise to secure the cover.

5-84

Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flames if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space. When you use anything from a container to clean your vehicle, be sure to follow the manufacturer’s warnings and instructions. And always open your doors or windows when you are cleaning the inside. Never use these to clean your vehicle: • Gasoline • Benzene • Naphtha • Carbon Tetrachloride • Acetone • Paint Thinner • Turpentine • Lacquer Thinner • Nail Polish Remover They can all be hazardous — some more than others — and they can all damage your vehicle, too.

5-85

A. Wrench B. Jack Handle C. Jack

{CAUTION:

Make sure the tire is secure. Driving with the tire not properly secured could injure pedestrians or damage the vehicle.

Do not use any of these unless this manual says you can. In many uses, these will damage your vehicle: • Alcohol • Laundry Soap • Bleach • Reducing Agents

Cleaning the Inside of Your Vehicle Use a vacuum cleaner often to get rid of dust and loose dirt. Wipe vinyl, leather, plastic and painted surfaces with a clean, damp cloth. Cleaning Fabric/Carpet Your dealer has cleaners for the cleaning of fabric and carpet. They will clean normal spots and stains very well. You can get GM-approved cleaning products from your dealer. See VehicleCare/AppearanceMaterialson page5-92. Here are some cleaning tips: • Always read the instructions on the cleaner label. • Clean up stains as soon as you can — before

they set.

5-86

• Carefully scrape off any excess stain. • Use a clean cloth or sponge, and change to a clean

area often. A soft brush may be used if stains are stubborn.

• If a ring forms on fabric after spot cleaning, clean

the entire area immediately or it will set.

Using Cleaner on Fabric 1. Vacuum and brush the area to remove any

loose dirt.

2. Always clean a whole trim panel or section.

Mask surrounding trim along stitch or welt lines.

3. Follow the directions on the container label. 4. Apply cleaner with a clean sponge. Do not saturate

the material and do not rub it roughly.

5. As soon as you have cleaned the section, use a

sponge to remove any excess cleaner.

6. Wipe cleaned area with a clean, water-dampened

towel or cloth.

7. Wipe with a clean cloth and let dry.

Special Fabric Cleaning Problems Stains caused by such things as catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, vomit, urine and blood can be removed as follows: 1. Carefully scrape off excess stain, then sponge the

soiled area with cool water.

2. If a stain remains, follow the cleaning instructions

described earlier.

3. If an odor lingers after cleaning vomit or urine, treat

the area with a water and baking soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml) of lukewarm water.

4. Let dry. Stains caused by candy, ice cream, mayonnaise, chili sauce and unknown stains can be removed as follows: 1. Carefully scrape off excess stain. 2. Clean with cool water and allow to dry completely. 3. If a stain remains, follow the cleaner instructions

described earlier.

Cleaning Vinyl Use warm water and a clean cloth. • Rub with a clean, damp cloth to remove dirt. You

may have to do this more than once.

• Things like tar, asphalt and shoe polish will stain if you do not get them off quickly. Use a clean cloth and vinyl cleaner. See your dealer for this product.

Cleaning Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap and wipe dry with a soft cloth. Then, let the leather dry naturally. Do not use heat to dry. • For stubborn stains, use a leather cleaner. • Neveruse oils, varnishes, solvent-based or abrasive cleaners, furniture polish or shoe polish on leather.

• Soiled or stained leather should be cleaned

immediately. If dirt is allowed to work into the finish, it can harm the leather.

5-87

Care of Safety Belts Keep belts clean and dry.

{CAUTION:

Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.

Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth at least every six months. During very cold, damp weather more frequent application may be required. See Part D:RecommendedFluidsandLubricantsonpage6-30.

Cleaning the Top of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Cleaning Interior Plastic Components Use only a mild soap and water solution on a soft cloth or sponge. Commercial cleaners may affect the surface finish. Cleaning Glass Surfaces Glass should be cleaned often. GM Glass Cleaner or a liquid household glass cleaner will remove normal tobacco smoke and dust films on interior glass. See VehicleCare/AppearanceMaterialsonpage5-92. Notice: If you use abrasive cleaners when cleaning glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the rear window defogger and the integrated radio antenna. When cleaning the glass on your vehicle, use only a soft cloth and glass cleaner.

5-88

Cleaning the Outside of Your Vehicle The paint finish on your vehicle provides beauty, depth of color, gloss retention and durability. Washing Your Vehicle The best way to preserve your vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Don’t wash your vehicle in the direct rays of the sun. Use a car washing soap. Don’t use strong soaps or chemical detergents. Be sure to rinse the vehicle well, removing all soap residue completely. You can get GM-approved cleaning products from your dealer. See VehicleCare/AppearanceMaterialsonpage5-92. Don’t use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter your vehicle.

Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing Your Vehicle.” Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get GM-approved cleaning products from your dealer. See VehicleCare/Appearance Materials on page5-92. If your vehicle has a “basecoat/clearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle.

5-89

Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible. Cleaning the Windshield, Backglass and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with a full-strength glass cleaning liquid. The windshield is clean if beads do not form when you rinse it with water.

Grime from the windshield will stick to the wiper blades and affect their performance. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Check the wiper blades and clean them as necessary; replace blades that look worn. Cleaning Aluminum Wheels Keep your wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. The surface of these wheels is similar to the painted surface of your vehicle. Don’t use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels. Don’t take your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes. These brushes can also damage the surface of these wheels.

5-90

Cleaning Tires To clean your tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.

Sheet Metal Damage If your vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.

Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials avaliable from your dealer. Larger areas of finish damage can be corrected in your dealer’s body and paint shop.

Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this for you.

Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, GM will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.

5-91

Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products.

Vehicle Care/Appearance Materials

(cont’d)

Description

Usage

Vehicle Care/Appearance Materials

Swirl Remover Polish

Description

Polishing Cloth Wax-Treated Tar and Road Oil Remover Chrome Cleaner and Polish White Sidewall Tire Cleaner

Vinyl Cleaner

Glass Cleaner

Chrome and Wire Wheel Cleaner

Finish Enhancer

Usage

Interior and exterior polishing cloth. Removes tar, road oil and asphalt. Use on chrome or stainless steel. Removes soil and black marks from whitewalls. Cleans vinyl tops, upholstery and convertible tops. Removes dirt, grime, smoke and fingerprints. Removes dirt and grime from chrome wheels and wire wheel covers. Removes dust, fingerprints, and surface contaminants. Spray on wipe off.

5-92

Cleaner Wax

Foaming Tire Shine Low Gloss

Wash Wax Concentrate

Spot Lifter

Odor Eliminator

Removes swirl marks, fine scratches and other light surface contamination. Removes light scratches and protects finish. Cleans, shines and protects in one easy step, no wiping necessary. Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free. Quickly and easily removes spots and stains from carpets, vinyl and cloth upholstery. Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet.

See your General Motors parts department for these products. See PartD:RecommendedFluidsand Lubricantsonpage6-30.

Vehicle Identification

Vehicle Identification Number (VIN)

This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration. Engine Identification The 8th character in your VIN is the engine code. This code will help you identify your engine, specifications and replacement parts.

Service Parts Identification Label You’ll find this label inside the glove box on the door. It’s very helpful if you ever need to order parts. On this label is: • your VIN, • the model designation, • paint information and • a list of all production options and special

equipment.

Be sure that this label is not removed from the vehicle. Electrical System

Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Your vehicle has an air bag system. Before attempting to add anything electrical to your vehicle, see ServicingYourAirBag-EquippedVehicleonpage1-58.

5-93

Instrument Panel Fuse Block

This fuse block is located under the driver’s side of the instrument panel. The fuses here protect each separate circuit including headlamps. There are spare fuses inside the fuse box. If you have electrical failure, check here first.

Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by fuses, circuit breakers and thermal links in the wiring itself. This greatly reduces the chance of fires caused by electrical problems. Look at the metallic band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the correct size. If you ever have a problem on the road and don’t have a spare fuse, you can borrow one. Just pick some feature of your vehicle that you can get along without — like the radio or cigarette lighter — and use its fuse, if it is the size you need. Replace it as soon as you can. Before replacing a fuse, turn every vehicle electrical switch off. There are two fuse blocks in your vehicle: the instrument panel fuse block and the engine compartment fuse block.

5-94

Fuses

Usage

P/W DOM

TAIL

HAZ

IG

CIG

D/L

STP

FOG

DEF

S/H

TRN

WIP

Power Windows Dome Light, Radio Memory License Plate Light, Clearance/Marker Lights, Instrument Panel Illumination, Warning Tone Hazard Lights, Turn Signal Oxygen Sensor Heater, Cruise Control, Ignition Coil, Meter, G Sensor Cigar/Cigarette Lighter, Radio, Power Mirror Door Locks Brake Light, Horn, Center High-Mounted Stop Lamp, Cruise Control Not Used Rear Window Defogger, DRL, Heater, Air Conditioning Not Used Turn Signal, Back-Up Light, Hazard Lights Windshield Wiper/Washer, Rear Window Wiper/Washer

Fuses for the air bags and the heater/air conditioning system are located next to the instrument panel fuse block.

5-95

Engine Compartment Fuse Block

For access to the main fuses, pull off the cover.

The engine compartment fuse block is located in the engine compartment on the passenger’s side of the vehicle and protects all electrical loads. See Engine Compartment Overview on page5-12 for more information on location.

Fuses/Relays

Usage

Accessory Power Outlet Electronic Fuel Injection System Right Headlamp Left Headlamp, High-Beam Indicator Heater Hazard Lamps, Rear Combination Lamps, Dome Light, Horn Cigar Lighter, Radio, I.G., Meter, Wiper, Washer, Rear Defroster, Turn Signals, Back-Up Lamps

5-96

Fuses/Relays

Usage

Fuses/Relays

Usage

10
11

(2.5L Engine

Only)

Anti-Lock Brake System All Electrical Loads Shift Lock (Relay)

Horn (Relay)

12

13

14

Air Conditioning Compressor (Relay) Air Conditioning Condenser Fan (Relay) Air Conditioning

5-97

Capacities and Specifications The following approximate capacities are given in English and metric conversions.

Capacities and Specifications

Capacities

Application

Air Conditioning Refrigerant R134a and Polyalkylene Glycol (PAG) refrigerant oil with dye Automatic Transmission

Drain and Refill

Cooling System Differential

Front Rear

Engine Oil with Filter Fuel Tank Manual Transmission

Four-Wheel Drive Two-Wheel Drive

5-98

English

0.9 lbs.

2.6 quarts

8.5 quarts

1.1 quarts 2.3 quarts

5.8 quarts 16.9 gallons

1.6 quarts 2.0 quarts

Metric

0.4 kg

2.5 L*

8.0 L

1.0 L* 2.2 L*

5.5 L** 64 L

1.5 L* 1.9 L*

Capacities and Specifications (cont’d)

Application

Transfer Case

Wheels and Tires

Wheel Nut Torque Plastic Wheel Nut Cap Torque

Capacities

English 1.8 quarts

Tighten by hand plus

one half turn with wheel

73 lbft

wrench

Metric 1.7 L

100 Y

*Recheck fluid level after filling. See AutomaticTransmissionFluidonpage5-20 or ManualTransmissionFluidon page5-23. **When changing the oil filter, additional oil may be needed. Recheck the oil level after filling. See EngineOilon page5-13.

Engine

V6

VIN Code

Transmission

Automatic

Spark Plug Gap

0.043 inch (1.1 mm)

Engine Specifications

5-99

Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer.

Part

Engine Air Cleaner/Filter Engine Oil Filter Passenger Compartment Air Filters PCV Valve Remote Keyless Entry Transmitter Battery

Spark Plugs

GM Part Number 30025009 or equivalent 91176162 or equivalent 91175923 or equivalent 91176183 or equivalent 3-volt CR2032 or equivalent 91176020 (NGK IFR5J11/Iridium plug), 91173854 (NGK BKR6E11/Nickel plug) or 91173855 (DENSO K20PR-U11/Nickel plug)

5-100

Engine Drive Belt Routing

5-101

- NOTES

5-102

Section 6

Maintenance Schedule

Maintenance Schedule ......................................6-2
Introduction ...................................................6-2
Maintenance Requirements ..............................6-2
Your Vehicle and the Environment ....................6-2
How This Section is Organized .........................6-3
Part A: Scheduled Maintenance Services ...........6-4
Using Your Maintenance Schedule ....................6-4
Selecting the Right Schedule ...........................6-4
Short Trip/City Scheduled Maintenance ..............6-7
Long Trip/Highway Scheduled Maintenance ......6-17
Part B: Owner Checks and Services ................6-24
At Each Fuel Fill ..........................................6-24
At Least Once a Month .................................6-24
At Least Twice a Year ...................................6-25

At Least Once a Year ...................................6-25
Part C: Periodic Maintenance Inspections .........6-28
Steering, Suspension and Front Drive Axle

Boot and Seal Inspection ............................6-28
Exhaust System Inspection ............................6-28
Fuel System Inspection ..................................6-28
Engine Cooling System Inspection ...................6-28
Throttle System Inspection .............................6-29
Rear Axle and Front Axle (Four-Wheel-Drive)

Service ....................................................6-29
Brake System Inspection ................................6-29
Part D: Recommended Fluids and

Lubricants ................................................6-30
Part E: Maintenance Record ...........................6-32

6-1

Maintenance Schedule

Introduction Important: Keep engine oil at the proper level and change as recommended.

HaveyoupurchasedtheGMProtectionPlan?ThePlan supplementsyournewvehiclewarranties.Seeyour WarrantyandOwnerAssistancebookletoryourdealer fordetails.

Maintenance Requirements Maintenance intervals, checks, inspections and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance may not be covered by warranty.

Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.

6-2

How This Section is Organized This maintenance schedule is divided into five parts: “Part A: Scheduled Maintenance Services” explains what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your GM dealer’s service department do these jobs. Your GM dealer has GM-trained and supported service people that will perform the work using genuine GM parts.

{CAUTION:

Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, have a qualified technician do the work.

If you want to get the service information, see Service PublicationsOrderingInformationonpage7-11. “Part B: Owner Checks and Services” tells you what should be checked and when. It also explains what you can easily do to help keep your vehicle in good condition. “Part C: Periodic Maintenance Inspections” explains important inspections that your dealer’s service department can perform for you. “Part D: Recommended Fluids and Lubricants” lists some recommended products necessary to help keep your vehicle properly maintained. These products, or their equivalents, should be used whether you do the work yourself or have it done. “Part E: Maintenance Record” is a place for you to record and keep track of the maintenance performed on your vehicle. Keep your maintenance receipts. They may be needed to qualify your vehicle for warranty repairs.

6-3

Part A: Scheduled Maintenance Services In this part are scheduled maintenance services which are to be performed at the mileage intervals specified.

Using Your Maintenance Schedule We at General Motors want to keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in many other ways. Because of the different ways people use their vehicles, maintenance needs may vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have questions on how to keep your vehicle in good condition, see your dealer. This part tells you the maintenance services you should have done and when to schedule them. When you go to your dealer for your service needs, you will know that GM-trained and supported service people will perform the work using genuine GM parts.

6-4

The proper fluids and lubricants to use are listed in Part D. Make sure whoever services your vehicle uses these. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. These schedules are for vehicles that: • carry passengers and cargo within recommended limits. You will find these on the tire and loading information label. See LoadingYourVehicle on page4-51.

• are driven on reasonable road surfaces within legal

driving limits.

• are driven off-road in the recommended manner. See Off-RoadDrivingwithYourFour-Wheel-Drive Vehicle on page4-16.

• use the recommended fuel. See GasolineOctane

on page5-4.

Selecting the Right Schedule First you will need to decide which of the two schedules is right for your vehicle. Here is how to decide which schedule to follow:

Short Trip/City Definition Follow the Short Trip/City Scheduled Maintenance if any one of these conditions is true for your vehicle: • Most trips are less than 5 miles (8 km). This is

particularly important when outside temperatures are below freezing.

• Most trips include extensive idling (such as frequent

driving in stop-and-go traffic).

• You frequently tow a trailer or use a carrier on top

of your vehicle.

• If the vehicle is used for delivery service, police,

taxi or other commercial application.

Oneofthereasonsyoushouldfollowthisscheduleif youoperateyourvehicleunderanyoftheseconditions isthattheseconditionscauseengineoiltobreak downsooner.

Short Trip/City Intervals

Every 3,000 Miles (5 000 km): Engine Oil and Filter Change (or 3 months, whichever occurs first).

Every 6,000 Miles (10 000 km): Passenger Compartment Air Filter Inspection (If Equipped). Tire Rotation.

Every 15,000 Miles (25 000 km): Engine Air Cleaner Filter Inspection. Automatic Transmission Service (severe conditions only). Manual Transmission Fluid Change. Transfer Case Fluid Change. Differential Fluid Change. Propeller Shafts and U-Joints Inspection (or every 15 months, whichever occurs first).

Every 30,000 Miles (50 000 km): Engine Air Cleaner Filter Replacement. Air Filter Replacement (If Equipped). Ignition Coil Plug Cap Inspection (or every 30 months, whichever occurs first). Engine Accessory Drive Belt Inspection (or every 30 months, whichever occurs first). Cooling System Service (or every 30 months, whichever occurs first). Fuel Tank, Cap, and Lines Inspection. Fuel Filter Replacement (or every 30 months, whichever occurs first).

6-5

Every 45,000 Miles (75 000 km): Automatic Transmission Fluid Hose Inspection (or every 45 months, whichever occurs first).

Every 60,000 Miles (100 000 km): Fuel Tank Cap Gasket Replacement. Emission System Hoses Inspection. Brake Fluid Service. Spark Plug Replacement.

Every 100,000 Miles (166 000 km): Automatic Transmission Service (normal conditions).

Every 120 000 Miles (200 000 km): Evaporative Emissions Canister and Air Suction Filter Replacement (or every 120 months, whichever occurs first). Engine Accessory Drive Belt Replacement (or every 120 months, whichever occurs first). Theseintervalsonlysummarizemaintenanceservices. Besuretofollowthecompletescheduledmaintenance onthefollowingpages.

Long Trip/Highway Definition Follow this scheduled maintenance only if none of the conditions from the Short Trip/City Scheduled Maintenance are true. Do not use this schedule if the vehicle is used for trailer towing, driven in a dusty area or used off paved roads. Use the Short Trip/City schedule for these conditions. Drivingavehiclewithafullywarmedengineunder highwayconditionswillcauseengineoiltobreakdown slower. Long Trip/Highway Intervals

Every 7,500 Miles (12 500 km): Engine Oil and Filter Change (or every 7.5 months, whichever occurs first). Tire Rotation.

Every 15,000 Miles (25 000 km): Engine Air Cleaner Filter Inspection. Automatic Transmission Service (severe conditions only). Passenger Compartment Air Filter Inspection (If Equipped). Propeller Shafts and U-Joints Inspection (or every 15 months, whichever occurs first).

6-6

Every 30,000 Miles (50 000 km): Engine Accessory Drive Belt Inspection (or every 30 months, whichever occurs first). Cooling System Service (or every 30 months, whichever occurs first). Fuel Tank, Cap and Lines Inspection. Engine Air Cleaner Filter Replacement. Passenger Compartment Air Filter Replacement (If Equipped). Ignition Coil Plug Cap Inspection (or every 30 months, whichever occurs first). Manual Transmission Fluid Change. Transfer Case Fluid Change. Differential Fluid Change. Fuel Filter Replacement (or every 30 months, whichever occurs first).

Every 45,000 Miles (75 000 km): Automatic Transmission Fluid Hose Inspection (or every 45 months, whichever occurs first).

Every 60,000 Miles (100 000 km): Fuel Tank Cap Gasket Replacement. Emission System Hoses Inspection. Spark Plug Replacement. Brake Fluid Service.

Every 100,000 Miles (166 000 km): Automatic Transmission Service (normal conditions).

Every 120,000 Miles (200 000 km): Evaporative Emissions Canister and Air Suction Filter Replacement (or every 120 months, whichever occurs first). Theseintervalsonlysummarizemaintenanceservices. Besuretofollowthecompletescheduledmaintenance onthefollowingpages.

Short Trip/City Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life of this vehicle. The service shown at 120,000 miles (200 000 km) should be repeated at the same interval after 120,000 miles (200 000 km) for the life of this vehicle. See PartB:OwnerChecksandServicesonpage6-24
and PartC:PeriodicMaintenanceInspectionson page6-28. Footnotes † TheU.S.EnvironmentalProtectionAgencyorthe CaliforniaAirResourcesBoardhasdeterminedthatthe failuretoperformthismaintenanceitemwillnotnullify theemissionwarrantyorlimitrecallliabilitypriorto thecompletionofthevehicle’susefullife.We,however, urgethatallrecommendedmaintenanceservicesbe performedattheindicatedintervalsandthe maintenanceberecorded. + Agoodtimetocheckyourbrakesisduringtire rotation.SeeBrakeSystemInspectiononpage6-29.

6-7

15,000 Miles (25 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. Inspect engine air cleaner filter. If necessary, replace the filter. If vehicle is driven in dusty/dirty conditions, inspect filter at every engine oil change. See EngineAirCleaner/Filteronpage5-18 for more information.AnEmissionControlService. (Seefootnote†.)

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

3,000 Miles (5 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

6,000 Miles (10 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.) 9,000 Miles (15 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

12,000 Miles (20 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

6-8

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km). q Change manual transmission fluid. q Change transfer case fluid. q Change differential fluid.

Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

18,000 Miles (30 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

21,000 Miles (35 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

24,000 Miles (40 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

27,000 Miles (45 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

30,000 Miles (50 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Replace passenger compartment air filters. Inspect fuel tank, cap and lines for damage or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. AnEmissionControlService. (Seefootnote†.) Inspect engine accessory drive belts (or every 30 months, whichever occurs first). AnEmission ControlService.

6-9

q Drain, flush and refill cooling system (or every

30 months, whichever occurs first). See Engine Coolantonpage5-25 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. AnEmissionControlService.(Seefootnote†.) Inspect ignition coil plug cap (or every 30 months, whichever occurs first). AnEmissionControl Service.(Seefootnote†.)

q Replace engine air cleaner filter. See EngineAir Cleaner/Filteronpage5-18 for more information. AnEmissionControlService.

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km). q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

q Change manual transmission fluid. q Change transfer case fluid. q Change differential fluid. q Replace fuel filter (or every 30 months, whichever

occurs first, or sooner if filter is clogged). An EmissionControlService.(Seefootnote†.) Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

33,000 Miles (55 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

6-10

36,000 Miles (60 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

39,000 Miles (65 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

42,000 Miles (70 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

45,000 Miles (75 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. Inspect automatic transmission fluid hose (or every 45 months, whichever occurs first).

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km).

Inspect engine air cleaner filter. If necessary, replace the filter. If vehicle is driven in dusty/dirty conditions, inspect filter at every engine oil change. See EngineAirCleaner/Filteronpage5-18 for more information.AnEmissionControlService. (Seefootnote†.)

q Change manual transmission fluid. q Change transfer case fluid. q Change differential fluid.

Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

6-11

48,000 Miles (80 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

51,000 Miles (85 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

54,000 Miles (90 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

57,000 Miles (95 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

60,000 Miles (100 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Replace passenger compartment air filters.

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

6-12

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km).

Inspect engine accessory drive belts (or every 30 months, whichever occurs first). AnEmission ControlService.

q Drain, flush and refill cooling system (or every

30 months, whichever occurs first). See Engine Coolantonpage5-25 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. AnEmissionControlService.(Seefootnote†.) q Replace spark plugs. AnEmissionControlService.

Inspect ignition coil plug cap (or every 30 months, whichever occurs first). AnEmissionControl Service.

q Drain, refill and bleed the brake system.

Inspect fuel tank, cap and lines for damage or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. AnEmissionControlService. (Seefootnote†.)

q Replace engine air cleaner filter. See EngineAir Cleaner/Filteronpage5-18 for more information. AnEmissionControlService.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

q Replace fuel filter (or every 30 months, whichever

occurs first).AnEmissionControlService. (Seefootnote†.)

q Change manual transmission fluid. q Change transfer case fluid. q Change differential fluid.

Inspect emission system hoses and replace as necessary. AnEmissionControlService. (Seefootnote†.) Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

63,000 Miles (105 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

66,000 Miles (110 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

6-13

69,000 Miles (115 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

72,000 Miles (120 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

75,000 Miles (125 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

6-14

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km).

Inspect engine air cleaner filter. If necessary, replace the filter. If vehicle is driven in dusty/dirty conditions, inspect filter at every engine oil change. See EngineAirCleaner/Filteronpage5-18 for more information.AnEmissionControlService. (Seefootnote†.)

q Change manual transmission fluid. q Change transfer case fluid. q Change differential fluid.

Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

78,000 Miles (130 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

81,000 Miles (135 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

84,000 Miles (140 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

87,000 Miles (145 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

90,000 Miles (150 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Replace passenger compartment air filters. Inspect automatic transmission fluid hose (or every 45 months, whichever occurs first).

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km).

Inspect engine accessory drive belts (or every 30 months, whichever occurs first). AnEmissionControlService. Inspect fuel tank, cap and lines for damage or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. AnEmissionControlService. (Seefootnote†.) Inspect ignition coil plug cap (or every 30 months, whichever occurs first). AnEmissionControl Service.

6-15

q Drain, flush and refill cooling system (or every

30 months, whichever occurs first). See Engine Coolantonpage5-25 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. AnEmissionControlService.(Seefootnote†.)

q Replace engine air cleaner filter. See Engine

AirCleaner/Filteronpage5-18 for more information. AnEmissionControlService.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

q Change manual transmission fluid. q Change transfer case fluid. q Change differential fluid. q Replace fuel filter (or every 30 months, whichever

occurs first).AnEmissionControlService. (Seefootnote†.) Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

6-16

93,000 Miles (155 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

96,000 Miles (160 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService. If Equipped: Inspect passenger compartment air filters.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

99,000 Miles (165 000 km) q Change engine oil and filter (or every 3 months,

whichever occurs first). AnEmissionControlService.

100,000 Miles (166 000 km)

If you have not used your vehicle under severe service conditions listed previously and, therefore, have not changed your automatic transmission fluid, change both the fluid and filter.

120,000 Miles (200 000 km) q Replace evaporative emission canister and air

suction filter (or every 120 months, whichever occurs first). AnEmissionControlService.

Long Trip/Highway Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life of this vehicle. The services shown at 120,000 miles (200 000 km) should be repeated at the same interval after 120,000 miles (200 000 km) for the life of this vehicle. See PartB:OwnerChecksandServicesonpage6-24
and PartC:PeriodicMaintenanceInspectionson page6-28. Footnotes † TheU.S.EnvironmentalProtectionAgencyorthe CaliforniaAirResourcesBoardhasdeterminedthatthe failuretoperformthismaintenanceitemwillnotnullify theemissionwarrantyorlimitrecallliabilitypriorto thecompletionofthevehicle’susefullife.We,however, urgethatallrecommendedmaintenanceservicesbe performedattheindicatedintervalsandthe maintenanceberecorded. + Agoodtimetocheckyourbrakesisduringtire rotation.SeeBrakeSystemInspectiononpage6-29.

7,500 Miles (12 500 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

15,000 Miles (25 000 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service. Inspect engine air cleaner filter. See EngineAir Cleaner/Filteronpage5-18 for more information. AnEmissionControlService.(Seefootnote†.) If Equipped: Inspect passenger compartment air filters.

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

6-17

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km). q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.) Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

22,500 Miles (37 500 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

30,000 Miles (50 000 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service. If Equipped: Replace passenger compartment air filters.

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km). q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.) Inspect engine accessory drive belts (or every 30 months, whichever occurs first). AnEmission ControlService.

q Drain, flush and refill cooling system (or every

30 months, whichever occurs first). See Engine Coolantonpage5-25 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. AnEmissionControlService.(Seefootnote†.)

6-18

Inspect ignition coil plug cap (or every 30 months, whichever occurs first). AnEmissionControl Service.(Seefootnote†.)

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

q Replace engine air cleaner filter. See EngineAir Cleaner/Filteronpage5-18 for more information. AnEmissionControlService. Inspect fuel tank, cap and lines for damage or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. AnEmissionControlService.(See footnote†.)

q Change manual transmission fluid. q Change transfer case fluid. q Change differential fluid. q Replace fuel filter (or every 30 months, whichever

occurs first, or sooner if filter is clogged). An EmissionControlService.(Seefootnote†.) Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

37,500 Miles (62 500 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service.

45,000 Miles (75 000 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service. Inspect engine air cleaner filter. See EngineAir Cleaner/Filteronpage5-18 for more information. An EmissionControlService.(Seefootnote†.) If Equipped: Inspect passenger compartment air filters. Inspect automatic transmission fluid hose (or every 45 months, whichever occurs first).

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

6-19

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km). q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.) Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

52,500 Miles (87 500 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

60,000 Miles (100 000 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service. If Equipped: Replace passenger compartment air filters.

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

Ifyoudonotuseyourvehicleunderanyofthese conditions, change the fluid and filter every 100,000miles(166000km). q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.) Inspect engine accessory drive belts (or every 30 months, whichever occurs first). AnEmission ControlService.

q Drain, flush and refill cooling system (or every

30 months, whichever occurs first). See Engine Coolantonpage5-25 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. AnEmissionControlService.(Seefootnote†.) q Replace spark plugs. AnEmissionControlService.

6-20

Inspect ignition coil plug cap (or every 30 months, whichever occurs first). AnEmissionControl Service.

q Replace engine air cleaner filter. See EngineAir Cleaner/Filteronpage5-18 for more information. AnEmissionControlService. Inspect fuel tank, cap and lines for damage or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. AnEmissionControlService. (Seefootnote†.)

q Change manual transmission fluid. q Change transfer case fluid. q Change differential fluid. q Replace fuel filter (or every 30 months, whichever

occurs first.AnEmissionControlService. (Seefootnote†.) Inspect emission system hoses and replace as necessary. AnEmissionControlService. (Seefootnote†.) Inspect propeller shafts and U-joints for looseness and damage (or every 15 months, whichever occurs first). Inspect more frequently if used off-road or for pulling a trailer. Tighten U-joint flange bolts if necessary.

q Drain, refill and bleed the brake system.

67,500 Miles (112 500 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service.

q Rotate tires. See TireInspectionandRotationon

page5-64 for proper rotation pattern and additional information. (Seefootnote+.)

75,000 Miles (125 000 km) q Change engine oil and filter (or every 7.5 months,

whichever occurs first). AnEmissionControl Service. Inspect engine air cleaner filter. See EngineAir Cleaner/Filteronpage5-18 for more information. AnEmissionControlService.(Seefootnote†.) If Equipped: Inspect passenger compartment air filters.

q Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside

temperature regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing.