Download PDF Manual

electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others:


. Dispense fuel only into


approved containers.


. Do not fill a container while it


is inside a vehicle, in a vehicle's trunk, pickup bed, or on any surface other than the ground.


(Continued)


WARNING (Continued)


. Bring the fill nozzle in contact


with the inside of the fill opening before operating the nozzle. Contact should be maintained until the filling is complete.


. Do not smoke while


pumping fuel.


. Do not use a cellular phone


while pumping fuel.


Driving and Operating


9-69


Towing


General Towing Information Only use towing equipment that has been designed for the vehicle. Contact your dealer or trailering dealer for assistance with preparing the vehicle for towing a trailer. See the following trailer towing information in this section:


For information on driving while towing a trailer, see “Driving Characteristics and Towing Tips.” For maximum vehicle and trailer weights, see “Trailer Towing.” For information on equipment to tow a trailer, see “Towing Equipment.”


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (70,1)


9-70


Driving and Operating


For information on towing a disabled vehicle, see Towing the Vehicle on page 10‑93. For information on towing the vehicle behind another vehicle such as a motor home, see Recreational Vehicle Towing on page 10‑93.


Driving Characteristics and Towing Tips


Pulling a Trailer Here are some important points:


There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.


. Consider using a sway control.


See “Hitches” in Towing Equipment on page 9‑79.


. Do not tow a trailer at all during the first 800 km (500 mi) the new vehicle is driven. The engine, axle or other parts could be damaged. Then, during the first 800 km (500 mi) that a trailer is towed, do not drive over 80 km/h (50 mph) and do not make starts at full throttle. This helps the engine and other parts of the vehicle wear in at the heavier loads.


. Vehicles can tow in D (Drive).


Shift the transmission to a lower gear if the transmission shifts too often under heavy loads and/or hilly conditions.


If the vehicle has the Side Blind Zone Alert (SBZA) system and it doesn't seem to be working properly while pulling a trailer, turn the system off. See Side Blind Zone Alert (SBZA) on page 9‑56 for more information. Important considerations that have to do with weight:


The weight of the trailer The weight of the trailer tongue The weight on the vehicle's tires


. And the weight of the trailering


combination


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (71,1)


Driving with a Trailer


{ WARNING


When towing a trailer, exhaust gases may collect at the rear of the vehicle and enter if the liftgate, trunk/hatch, or rear-most window is open. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. To maximize safety when towing a trailer:


. Have the exhaust system


inspected for leaks and make necessary repairs before starting a trip.


. Never drive with the liftgate,


trunk/hatch, or rear-most window open.


(Continued)


WARNING (Continued)


. Fully open the air outlets on


or under the instrument panel.


. Adjust the Climate Control


system to a setting that brings in only outside air and set the fan speed to the highest setting. See Climate Control System in the Index.


For more information about Carbon Monoxide, see Engine Exhaust on page 9‑30.


Towing a trailer requires a certain amount of experience. The combination you are driving is longer and not as responsive as the vehicle itself. Get acquainted with the handling and braking of the rig before setting out for the open road.


Driving and Operating


9-71


Before starting, check all trailer hitch parts and attachments, safety chains, electrical connectors, lamps, tires and mirrors. If the trailer has electric brakes, start the combination moving and then apply the trailer brake controller by hand to be sure the brakes work. During the trip, check occasionally to be sure that the load is secure and the lamps and any trailer brakes still work. Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer. This can help to avoid heavy braking and sudden turns. Passing More passing distance is needed when towing a trailer. The combination will not accelerate as quickly and is longer so it is necessary to go much farther beyond the passed vehicle before returning to the lane.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (72,1)


9-72


Driving and Operating


Backing Up Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, move that hand to the left. To move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you. Making Turns Notice: Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle. The vehicle could be damaged. Avoid making very sharp turns while trailering. When turning with a trailer, make wider turns than normal. Do this so the trailer will not strike soft shoulders, curbs, road signs, trees or other objects. Avoid jerky or sudden maneuvers. Signal well in advance.


If the trailer turn signal bulbs burn out, the arrows on the instrument panel will still flash for turns. It is important to check occasionally to be sure the trailer bulbs are still working. Driving on Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the brakes might get hot and no longer work well. Vehicles can tow in D (Drive). Shift the transmission to a lower gear if the transmission shifts too often under heavy loads and/or hilly conditions. The tow/haul mode may be used if the transmission shifts too often. See Tow/Haul Mode Light on page 5‑24.


When towing at high altitude on steep uphill grades, consider the following: Engine coolant will boil at a lower temperature than at normal altitudes. If the engine is turned off immediately after towing at high altitude on steep uphill grades, the vehicle may show signs similar to engine overheating. To avoid this, let the engine run while parked, preferably on level ground, with the automatic transmission in P (Park) for a few minutes before turning the engine off. If the overheat warning comes on, see Engine Overheating on page 10‑21.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (73,1)


Driving and Operating


9-73


WARNING (Continued)


Always put the shift lever fully in P (Park) with the parking brake firmly set. If the transfer case on a four-wheel-drive vehicle is in N (Neutral), the vehicle will be free to roll, even if the shift lever is in P (Park). Be sure the transfer case is in a drive gear — not in N (Neutral).


Parking on Hills


{ WARNING


Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.


If parking the rig on a hill: 1. Press the brake pedal, but do not shift into P (Park) yet. Turn the wheels into the curb if facing downhill or into traffic if facing uphill.


2. Have someone place chocks


under the trailer wheels.


3. When the wheel chocks are in


place, release the regular brakes until the chocks absorb the load.


4. Reapply the brake pedal. Then


5.


apply the parking brake and shift into P (Park). If the vehicle is four-wheel-drive and has a two-speed transfer case, be sure the transfer case is in a drive gear and not in N (Neutral).


6. Release the brake pedal. { WARNING


It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If the engine has been left running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when on fairly level ground, use the steps that follow.


(Continued)


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (74,1)


9-74


Driving and Operating


Leaving After Parking on a Hill 1. Apply and hold the brake pedal. 2. Start the engine. 3. Shift into a gear. 4. Release the parking brake. 5. Let up on the brake pedal. 6. Drive slowly until the trailer is


clear of the chocks.


7. Stop and have someone pick up


and store the chocks.


Maintenance When Trailer Towing The vehicle needs service more often when pulling a trailer. See Maintenance Schedule on page 11‑3. Things that are especially important in trailer operation are automatic transmission fluid, engine oil, axle lubricant, belts, cooling system and brake system. It is a good idea to inspect these before and during the trip. Check periodically to see that all hitch nuts and bolts are tight.


Trailer Towing If the vehicle has a hybrid engine, see the Hybrid supplement for more information. Do not tow a trailer during break‐in. See New Vehicle Break-In on page 9‑22 for more information.


{ WARNING


The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well — or even at all. The driver and passengers could be seriously injured. The vehicle may also be damaged; the resulting repairs would not be covered by the vehicle warranty. Pull a trailer only if all the steps in this section have been followed. Ask your dealer for advice and information about towing a trailer with the vehicle.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (75,1)


Driving and Operating


9-75


Notice: Pulling a trailer improperly can damage the vehicle and result in costly repairs not covered by the vehicle warranty. To pull a trailer correctly, follow the advice in this section and see your dealer for important information about towing a trailer with the vehicle. To identify the trailering capacity of the vehicle, read the information in “Weight of the Trailer” that appears later in this section.


Trailering is different than just driving the vehicle by itself. Trailering means changes in handling, acceleration, braking, durability and fuel economy. Successful, safe trailering takes correct equipment, and it has to be used properly. The following information has many time-tested, important trailering tips and safety rules. Many of these are important for your safety and that of your passengers. So please read this section carefully before pulling a trailer.


Weight of the Trailer How heavy can a trailer safely be? It depends on how the rig is used. Speed, altitude, road grades, outside temperature, and how much the vehicle is used to pull a trailer are all important. It can depend on any special equipment on the vehicle, and the amount of tongue weight the vehicle can carry. See “Weight of the Trailer Tongue” later in this section for more information. Trailer weight rating (TWR) is calculated assuming the tow vehicle has only the driver but all required trailering equipment. Weight of additional optional equipment, passengers, and cargo in the tow vehicle must be subtracted from the trailer weight rating. Use the following chart to determine how much the vehicle can weigh, based upon the vehicle model and options.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (76,1)


9-76


Driving and Operating


Vehicle 1500 Series 2WD Short Wheel Base


5.3L V8
5.3L V8
5.3L V8 K5L HD Cooling Pkg


1500 Series 2WD Long Wheel Base


5.3L V8
5.3L V8
5.3L V8 K5L HD Cooling Pkg


1500 Series 4WD Short Wheel Base


5.3L V8
5.3L V8
5.3L V8 K5L HD Cooling Pkg


1500 Series 4WD Long Wheel Base


5.3L V8
5.3L V8
5.3L V8 K5L HD Cooling Pkg


Axle Ratio


Maximum Trailer Weight


GCWR*


3.08
3.42
3.42


3.08
3.42
3.42


3.08
3.42
3.42


3.08
3.42
3.42


2 495 kg (5,500 lbs) 2 722 kg (6,000 lbs) 3 856 kg (8,500 lbs)


4 990 kg (11,000 lbs) 5 216 kg (11,500 lbs) 6 350 kg (14,000 lbs)


2 313 kg (5,100 lbs) 2 540 kg (5,600 lbs) 3 674 kg (8,100 lbs)


4 990 kg (11,000 lbs) 5 216 kg (11,500 lbs) 6 350 kg (14,000 lbs)


2 359 kg (5,200 lbs) 2 586 kg (5,700 lbs) 3 720 kg (8,200 lbs)


4 990 kg (11,000 lbs) 5 216 kg (11,500 lbs) 6 350 kg (14,000 lbs)


2 268 kg (5,000 lbs) 2 495 kg (5,500 lbs) 3 629 kg (8,000 lbs)


4 990 kg (11,000 lbs) 5 216 kg (11,500 lbs) 6 350 kg (14,000 lbs)


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (77,1)


Driving and Operating


9-77


Vehicle 2500 Series 2WD Long Wheel Base


Axle Ratio


Maximum Trailer Weight


GCWR*


6.0L V8


3.73


4 355 kg (9,600 lbs)


7 257 kg (16,000 lbs)


2500 Series 4WD Long Wheel Base


6.0L V8


7 257 kg (16,000 lbs) *The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment and conversions. The GCWR for the vehicle should not be exceeded.


4 264 kg (9,400 lbs)


3.73


Ask your dealer for trailering information or advice, or write us at our Customer Assistance Offices, See Customer Assistance Offices (U.S. and Canada) on page 13‑5 or Customer Assistance Offices (Mexico) on page 13‑6.


Weight of the Trailer Tongue The tongue load (A) of any trailer is very important because it is also part of the vehicle weight. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle as well as trailer tongue weight. Vehicle options, equipment,


passengers and cargo in the vehicle reduce the amount of tongue weight the vehicle can carry, which will also reduce the trailer weight the vehicle can tow. See Vehicle Load Limits on page 9‑16 for more information about the vehicle's maximum load capacity.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (78,1)


9-78


Driving and Operating


Vehicle Series


Hitch Type


1500
2500
1500
2500


Weight Carrying Weight Carrying


Weight Distributing Weight Distributing


Maximum Tongue


Weight


272 kg (600 lbs) 453 kg (1,000 lbs) 499 kg (1,100 lbs) 680 kg (1,500 lbs)


Do not exceed the maximum allowable tongue weight for the vehicle. Choose the shortest hitch extension that will position the hitch ball closest to the vehicle. This will help reduce the effect of trailer tongue weight on the rear axle. Trailering may be limited by the vehicle's ability to carry tongue weight. Tongue weight cannot cause the vehicle to exceed the GVWR (Gross Vehicle Weight Rating) or


the RGAWR (Rear Gross Axle Weight Rating). See “Total Weight on the Vehicle's Tires” later in this section for more information. After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they are not, adjustments might be made by moving some items around in the trailer.


Trailer tongue weight (A) should be 10 percent to 15 percent of the loaded trailer weight (B) up to the maximums for vehicle series and hitch type.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (79,1)


Driving and Operating


9-79


Total Weight on the Vehicle's Tires Be sure the vehicle's tires are inflated to the inflation pressures found on the Certification label on the drivers door or see Vehicle Load Limits on page 9‑16 for more information. Make sure not to exceed the GVWR limit for the vehicle, or the RGAWR, with the tow vehicle and trailer fully loaded for the trip including the weight of the trailer tongue. If using a weight distributing hitch, make sure not to exceed the RGAWR before applying the weight distribution spring bars.


Weight of the Trailering Combination It is important that the combination of the tow vehicle and trailer does not exceed any of its weight ratings — GCWR, GVWR, RGAWR, Trailer Weight Rating or Tongue Weight. The only way to be sure it is not exceeding any of these ratings is to weigh the tow vehicle and trailer combination, fully loaded for the trip, getting individual weights for each of these items.


Towing Equipment


Hitches The correct hitch equipment helps maintain combination control. Most small-to-medium trailers can be towed with a weight carrying hitch which simply features a coupler latched to the hitch ball. Larger trailers may require a weight distributing hitch that uses spring bars to distribute the trailer tongue weight among the two vehicle and trailer axles. See “Weight of the Trailer Tongue” in Trailer Towing on page 9‑74 for rating limits with various hitch types. Consider using sway controls with any trailer. Ask a trailering professional about sway controls or refer to the trailer manufacturer's recommendations and instructions.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (80,1)


9-80


Driving and Operating


Weight‐Distributing Hitch Adjustment


A. Body to Ground Distance B. Front of Vehicle When using a weight-distributing hitch, the spring bars should be adjusted so the distance (A) is the same after coupling the trailer to the tow vehicle and adjusting the hitch.


Safety Chains Always attach chains between the vehicle and the trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer. If the trailer being towed weighs up to 2 271 kg (5,000 lbs) with a factory-installed step bumper, safety chains may be attached to the attaching points on the bumper, otherwise, safety chains should be attached to holes on the trailer hitch platform. Always leave just enough slack so the combination can turn. Never allow safety chains to drag on the ground.


Trailer Brakes A loaded trailer that weighs more than 900 kg (2,000 lbs) needs to have its own brake system that is adequate for the weight of the trailer. Be sure to read and follow the instructions for the trailer brakes so they are installed, adjusted and maintained properly. Since the vehicle is equipped with StabiliTrak®, the trailer brakes cannot tap into the vehicle's hydraulic system. Trailer Wiring Harness The vehicle is equipped with the following wiring harnesses for towing a trailer.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (81,1)


Basic Trailer Wiring The trailer wiring harness, with a seven-pin connector, is located at the rear of the vehicle and is tied to the vehicle's frame. The harness connector can be plugged into a seven-pin universal heavy-duty trailer connector available through your dealer. The seven-wire harness contains the following trailer circuits: . Yellow: Left Stop/Turn Signal . Dark Green: Right Stop/Turn


Signal


. Brown: Taillamps . White: Ground


Light Green: Back-up Lamps


. Red: Battery Feed* . Dark Blue: Trailer Brake*


Driving and Operating


9-81


*The fuses for these two circuits are installed in the underhood electrical center, but the wires are not connected. They should be connected by your dealer or a qualified service center.


Heavy-Duty Trailer Wiring Harness Package


The seven-wire harness contains the following trailer circuits: . Yellow: Left Stop/Turn Signal . Dark Green: Right Stop/Turn


Signal


. Brown: Taillamps . White: Ground


Light Green: Back-up Lamps


. Red: Battery Feed* . Dark Blue: Trailer Brake* *The fuses for these two circuits are installed in the underhood electrical center, but the wires are not connected. They should be connected by your dealer or a qualified service center.


The vehicle is equipped with the seven-wire trailer towing harness. This harness with a seven-pin universal trailer connector is attached to a bracket on the hitch platform.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (82,1)


9-82


Driving and Operating


If charging a remote (non-vehicle) battery, press the tow/haul mode button located at the end of the shift lever. This will boost the vehicle system voltage and properly charge the battery. If the trailer is too light for tow/haul mode, turn on the headlamps as a second way to boost the vehicle system and charge the battery. Electric Brake Control Wiring Provisions These wiring provisions are included with the vehicle as part of the trailer wiring package. These provisions are for an electric brake controller. The instrument panel contains blunt cut wires near the data link connector for the trailer brake controller. The harness contains the following wires: . Dark Blue: Brake Signal to


Trailer Connector


. Red/Black: Battery


Light Blue/White: Brake Switch


. White: Ground


It should be installed by your dealer or a qualified service center. If the vehicle is equipped with an ITBC, the blunt cuts exist, but are not connected further in the harness. If an aftermarket trailer brake controller is installed, the ITBC must be disconnected. Do not power both ITBC and aftermarket controllers to control the trailer brakes at the same time. Tow/Haul Mode


Pressing this button at the end of the shift lever turns on and off the tow/haul mode.


This indicator light on the instrument panel cluster comes on when the tow/haul mode is on. Tow/Haul is a feature that assists when pulling a heavy trailer or a large or heavy load. See Tow/Haul Mode on page 9‑36 for more information. Tow/Haul is designed to be most effective when the vehicle and trailer combined weight is at least 75 percent of the vehicle's Gross Combined Weight Rating (GCWR). See “Weight of the Trailer” earlier in the section. Tow/Haul is most useful under the following driving conditions: . When pulling a heavy trailer or a


large or heavy load through rolling terrain.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (83,1)


. When pulling a heavy trailer or a


large or heavy load in stop and go traffic.


. When pulling a heavy trailer or a


large or heavy load in busy parking lots where improved low speed control of the vehicle is desired.


Operating the vehicle in Tow/Haul when lightly loaded or with no trailer at all will not cause damage. However, there is no benefit to the selection of Tow/Haul when the vehicle is unloaded. Such a selection when unloaded may result in unpleasant engine and transmission driving characteristics and reduced fuel economy. Tow/ Haul is recommended only when pulling a heavy trailer or a large or heavy load.


Integrated Trailer Brake Control System


The vehicle may have an Integrated Trailer Brake Control (ITBC) system for electric trailer brakes. This symbol is located on the Trailer Brake Control Panel on vehicles with an Integrated Trailer Brake Control System. The power output to the trailer brakes is based on the amount of brake pressure being applied by the vehicle’s brake system. This available power output to the trailer brakes can be adjusted to a wide range of trailering situations.


Driving and Operating


9-83


The ITBC system is integrated with the vehicle’s brake, anti‐lock brake and StabiliTrak systems. In trailering conditions that cause the vehicle’s anti‐lock brake or StabiliTrak systems to activate, power sent to the trailer's brakes will be automatically adjusted to minimize trailer wheel lock-up. This does not imply that the trailer has the StabiliTrak system. Non-hybrid vehicles with StabiliTrak have a Trailer Sway Control (TSC) feature. See Trailer Sway Control (TSC) on page 9‑90. Non-hybrid vehicles with StabiliTrak have a Hill Start Assist (HSA) feature. See Hill Start Assist (HSA) on page 9‑47.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (84,1)


9-84


Driving and Operating


If the vehicle’s brake, anti‐lock brake or StabiliTrak systems are not functioning properly, the ITBC system may not be fully functional or may not function at all. Make sure all of these systems are fully operational to ensure full functionality of the ITBC system. The ITBC system is powered through the vehicle's electrical system. Turning the ignition off will also turn off the ITBC system. The ITBC system is fully functional only when the ignition is in ON or in RUN. The ITBC system can only be used with trailers with electric brakes.


{ WARNING


Connecting a trailer that is not compatible with the ITBC system may result in reduced or complete loss of trailer braking. There may be an increase in stopping distance or trailer instability which could result in personal injury or damage to the vehicle, trailer, or other property. An aftermarket controller may be available for use with trailers with surge, air, or electric‐over‐hydraulic trailer brake systems. To determine the type of brakes on the trailer and the availability of controllers, check with your trailer manufacturer or dealer.


When trailering, make sure of the following:


The ITBC system is used only with trailers that are equipped with electric brakes.


. All applicable local and federal


laws and regulations are followed.


. All electrical and mechanical connections to the trailer are made correctly. The trailer’s brakes are in proper working condition. The trailer and vehicle are properly loaded for the towing condition.


The ITBC system is a factory installed item. Out‐of‐factory installation of this system should not be attempted. GM is not responsible for warranty or performance of the system resulting from out‐of‐factory installation.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (85,1)


Trailer Brake Control Panel


A. Manual Trailer Brake Apply


Lever


B. Trailer Gain Adjustment Buttons


The ITBC system has a control panel located on the instrument panel to the left of the steering column. The control panel allows adjustment to the amount of output, referred to as trailer gain, available to the electric trailer brakes and allows manual application the trailer brakes. The Trailer Brake Control Panel is used along with the Trailer Brake Display Page on the DIC to adjust and display power output to the trailer brakes.


Trailer Brake DIC Display Page The ITBC system displays messages into the vehicle’s Driver Information Center (DIC). See Driver Information Center (DIC) on page 5‑28 for more information. The display page indicates Trailer Gain setting, power output to the electric trailer brakes, trailer connection and system operational status.


Driving and Operating


9-85


The Trailer Brake Display Page can be displayed by performing any of the following actions: . Scrolling through the DIC menu


pages using the odometer trip stem or the DIC Vehicle Information button (if equipped).


. Pressing a Trailer Gain


button – If the Trailer Brake Display Page is not currently displayed, pressing a Trailer Gain button will first recall the current Trailer Gain setting. After the Trailer Brake Display Page is displayed, each press and release of the gain buttons will then cause the Trailer Gain setting to change.


. Activating the Manual Trailer


Brake Apply lever


. Connecting a trailer equipped


with electric trailer brakes


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (86,1)


9-86


Driving and Operating


All DIC warning and service messages must first be acknowledged by the driver by pressing the odometer trip stem or the DIC Vehicle Information button (if equipped) before the Trailer Brake Display Page can be displayed and Trailer Gain can be adjusted. TRAILER GAIN – This setting is displayed anytime the Trailer Brake Display Page is active. This setting can be adjusted from 0.0 to 10.0
with either a trailer connected or disconnected. To adjust the Trailer Gain, press one of the Trailer Gain adjustment buttons located on the Trailer Brake Control Panel. Press and hold a gain button to cause the Trailer Gain to continuously adjust. To turn the output to the trailer off, adjust the Trailer Gain setting to 0.0 (zero).


0.0 (zero) gain is the factory default setting. To properly adjust trailer gain, see the Trailer Gain Adjustment Procedure later in this section. TRAILER OUTPUT – This is displayed any time a trailer with electric brakes is connected. Output to the electric brakes is based on the amount of vehicle braking present and relative to the Trailer Gain setting. Output is displayed from 0 to 10 bars for each gain setting. Non-hybrid vehicles with Trailer Sway Control (TSC) or Hill Start Assist (HSA), output to the electric trailer brakes may be displayed when the systems are active. See Trailer Sway Control (TSC) on page 9‑90 and Hill Start Assist (HSA) on page 9‑47.


The Trailer Output will indicate “- - - - - -“on the Trailer Brake Display Page whenever the following occur: . No trailer is connected. . A trailer without electric brakes is connected (no DIC message is displayed).


. A trailer with electric brakes


has become disconnected (a CHECK TRAILER WIRING message will also be displayed on the DIC). There is a fault present in the wiring to the electric trailer brakes (a CHECK TRAILER WIRING message will also be displayed on the DIC). There is a fault in the ITBC system (a SERVICE TRAILER BRAKE SYSTEM message will also be displayed in the DIC).


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (87,1)


Driving and Operating


9-87


Trailer Gain Adjustment Procedure Trailer Gain should be set for a specific trailering condition and must be adjusted any time vehicle loading, trailer loading or road surface conditions change. Setting the Trailer Gain properly is needed for the best trailer stopping performance. A trailer that is over-gained may result in locked trailer brakes. A trailer that is under-gained may result in not enough trailer braking. Both of these conditions may result in poorer stopping and stability of the vehicle and trailer.


Manual Trailer Brake Apply The Manual Trailer Brake Apply Lever is located on the Trailer Brake Control Panel and is used to apply the trailer’s electric brakes independent of the vehicle’s brakes. This lever is used in the Trailer Gain Adjustment Procedure to properly adjust the power output to the trailer brakes. Sliding the lever to the left will apply only the trailer brakes. The power output to the trailer is indicated in the Trailer Brake Display Page in the DIC. If the vehicle’s service brakes are applied while using the Manual Trailer Brake Apply Lever, the trailer output power will be the greater of the two. The trailer and the vehicle's brake lamps will come on when either vehicle braking or manual trailer brakes are applied.


Use the following procedure to correctly adjust Trailer Gain for each towing condition: 1. Make sure the trailer brakes are


in proper working condition.


2. Connect a properly loaded trailer


to the vehicle and make all necessary mechanical and electrical connections. See Vehicle Load Limits on page 9‑16 for more information. 3. After the electrical connection is made to a trailer equipped with electric brakes:


A TRAILER CONNECTED message will be briefly displayed on the DIC display. The Trailer Brake Display Page will appear on the DIC showing TRAILER GAIN and TRAILER OUTPUT.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (88,1)


9-88


Driving and Operating


In the Trailer Output display on the DIC, “- - - - - -“will disappear if there is no error present. Connecting a trailer without electric brakes will not clear the six dashed lines.


4. Adjust the Trailer Gain by using


the gain adjustment (+ / -) buttons on the Trailer Brake Control Panel.


5. Drive the vehicle with the trailer attached on a level road surface representative of the towing condition and free of traffic at about 32 to 40 km/h (20 to 25 mph) and fully apply the Manual Trailer Brake Apply lever. Adjusting trailer gain at speeds lower than 32 to 40 km/h (20 to 25 mph) may result in an incorrect gain setting.


6. Adjust the Trailer Gain to just


below the point of trailer wheel lock-up, indicated by trailer wheel squeal or tire smoke when a trailer wheel locks. Trailer wheel lock-up may not occur if towing a heavily loaded trailer. In this case, adjust the Trailer Gain to the highest allowable setting for the towing condition.


7. Re-adjust Trailer Gain any time


vehicle loading, trailer loading or road surface conditions change or if trailer wheel lock-up is noticed at any time while towing


Other ITBC Related DIC Messages In addition to displaying TRAILER GAIN and TRAILER OUTPUT through the DIC, trailer connection and ITBC system status is displayed in the DIC. TRAILER CONNECTED – This message will be briefly displayed when a trailer with electric brakes is first connected to the vehicle. This


message will automatically turn off in about ten seconds. The driver can also acknowledge this message before it automatically turns off. CHECK TRAILER WIRING – This message will be displayed if: 1. The ITBC system first


determines connection to a trailer with electric brakes and then the trailer harness becomes disconnected from the vehicle. If the disconnect occurs while the vehicle is stationary, this message will automatically turn off in about thirty seconds. This message will also turn off if the driver acknowledges this message off or if the trailer harness is re-connected. If the disconnect occurs while the vehicle is moving, this message will continue until the ignition is turned off. This message will also turn off if the driver acknowledges this message off or if the trailer harness is re-connected.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (89,1)


2. There is an electrical fault in the


wiring to the electric trailer brakes. This message will continue as long as there is an electrical fault in the trailer wiring. This message will also turn off if the driver acknowledges this message off. To determine if the electrical fault is on the vehicle side or trailer side of the trailer wiring harness connection, do the following: 1. Disconnect the trailer wiring


harness from the vehicle.


2. Turn the ignition OFF. 3. Wait ten seconds, then turn the


ignition back to RUN.


Driving and Operating


9-89


4.


If the CHECK TRAILER WIRING message re-appears, the electrical fault is on the vehicle side. If the CHECK TRAILER WIRING message only re-appears when connecting the trailer wiring harness to the vehicle, the electrical fault is on the trailer side.


SERVICE TRAILER BRAKE SYSTEM – This message will be displayed when there is a problem with the ITBC system. If this message persists over multiple ignition cycles there is problem with the ITBC system. Take the vehicle to an authorized GM dealer to have the ITBC system diagnosed and repaired.


If either the CHECK TRAILER WIRING or SERVICE TRAILER BRAKE SYSTEM message is displayed while driving the vehicle, power is no longer available to the trailer brakes. When traffic conditions allow, carefully pull the vehicle over to the side of the road and turn the ignition off. Check the wiring connection to the trailer and turn the ignition back on. If either of these messages continues, either the vehicle or trailer needs service. An authorized GM dealer may be able to diagnose and repair problems with the trailer. However, any diagnosis and repair of the trailer is not covered under the vehicle warranty. Please contact your trailer dealer for assistance with trailer repairs and trailer warranty information.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (90,1)


9-90


Driving and Operating


Trailer Sway Control (TSC) Non-hybrid vehicles with StabiliTrak have a Trailer Sway Control (TSC) feature. If the vehicle is towing a trailer and the system detects that the trailer is swaying, the vehicle brakes are applied without the driver pressing the brake pedal. If the vehicle is equipped with the Integrated Trailer Brake Control (ITBC) system, StabiliTrak may also apply the trailer brakes. The TCS/ StabiliTrak warning light will flash on the instrument panel cluster to notify the driver to reduce speed. If the trailer continues to sway, StabiliTrak will reduce engine torque to help slow the vehicle. See StabiliTrak® System on page 9‑47 for more information. Adding non‐dealer accessories can affect the vehicle performance. See Accessories and Modifications on page 10‑3 for more information.


Conversions and Add-Ons


Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle's warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain the vehicle's 12‐volt battery, even if the vehicle is not operating. The vehicle has an airbag system. Before attempting to add anything electrical to the vehicle, see Servicing the Airbag-Equipped Vehicle on page 3‑44 and Adding Equipment to the Airbag-Equipped Vehicle on page 3‑44.


Adding a Snow Plow or Similar Equipment Before installing a snow plow on the vehicle, here are some things you need to know: Notice: If the vehicle does not have the snow plow prep package, adding a plow can damage the vehicle, and the repairs would not be covered by warranty. Unless the vehicle was built to carry a snow plow, do not add one to the vehicle. If the vehicle has the snow plow prep package, called RPO VYU, then the payload the vehicle can carry will be reduced when a snow plow is installed. The vehicle can be damaged if either the front or rear axle ratings or the Gross Vehicle Weight Rating (GVWR) are exceeded.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (91,1)


Driving and Operating


9-91


Some vehicles are built with a special snow plow prep package, called RPO VYU. If the vehicle has this option, you can add a plow to it, provided certain weights, such as the weights on the vehicle's axles and the Gross Vehicle Weight Rating (GVWR), are not exceeded. The plow the vehicle can carry depends on many things, such as:


The options the vehicle came with, and the weight of those options. The weight and number of passengers intended to be carried. The weight of items added to the vehicle. The total weight of any additional cargo intended to be carried.


Say, for example, you have a 318 kg (700 lb) snow plow. The total weight of all occupants and cargo inside the cab should not exceed 135 kg (300 lb). This means that you may only be able to carry one passenger. But, even this may be too much if there is other equipment already adding to the weight of the vehicle. Here are some guidelines for safely carrying a snow plow on the vehicle: . Make sure the weight on the front and rear axles does not exceed the axle rating for each. For the front axle, if more cargo or passengers must be carried, appropriate counter ballast must be installed rear of the rear axle. Counter ballast must be properly secured so it will not move during driving.


Follow the snow plow manufacturer's recommendations regarding rear ballast. Rear ballast may be required to ensure a proper front and rear weight distribution ratio, even though the actual weight at the front axle may be less than the front axle rating. The snow plow manufacturer or installer can assist in determining the amount of rear ballast required, to help make sure the snowplow/vehicle combination does not exceed the GVW rating, the front and rear axle ratings, and the front and rear weight distribution ratio. The total vehicle must not exceed the GVW rating.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (92,1)


9-92


Driving and Operating


Front axle reserve capacity is the difference between the front Gross Axle Weight Rating (GAWR) and the front axle weight of the vehicle with full fuel and passengers. Basically, it is the amount of weight that can be added to the front axle before reaching the front GAWR. The front axle reserve capacity for the vehicle can be found in the lower right corner of the Certification/Tire label, as shown.


In order to calculate the amount of weight any front accessory, such as a snow plow, is adding to the front axle, use the following formula:


United States


Canada


(W x (A + W.B.)) /W.B.= Weight the accessory is adding to the front axle. Where:


W = Weight of added accessory A = Distance that the accessory is in front of the front axle W.B. = Vehicle Wheelbase


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (93,1)


For example, adding a 318 kg (700 lb) snow plow actually adds more than 318 kg (700 lb) to the front axle. Using the formula, if the snow plow is 122 cm (4 ft) in front of the front axle and the wheel base is 305 cm (10 ft), then:


W = 318 kg (700 lb) A = 122 cm (4 ft) W.B. = 305 cm (10 ft)


(W x (A + W.B.))/W.B. = (318 x (122 + 305))/305 = 445 kg (980 lb) So, if the vehicle's front axle reserve capacity is more than 980 lbs (445 kg), the snow plow could be added without exceeding the front GAWR. Heavier equipment can be added on the front of the vehicle if it is compensated for by carrying fewer passengers, less cargo, or by positioning cargo toward the rear. This has the effect of reducing the load on the front. However, the front


GAWR, rear GAWR, and the Gross Vehicle Weight Rating (GVWR) must never be exceeded. { WARNING


On some vehicles that have certain front mounted equipment, such as a snow plow, it may be possible to load the front axle to the front gross axle weight rating (GAWR) but not have enough weight on the rear axle to have proper braking performance. If the brakes cannot work properly, you could have a crash. To help the brakes work properly when a snow plow is installed, always follow the snow plow manufacturer or installer's recommendation for rear ballast to ensure a proper front and rear weight distribution ratio, even though the actual front weight may be less than the front GAWR, and the total vehicle


(Continued)


Driving and Operating


9-93


WARNING (Continued)


weight is less than the gross vehicle weight rating (GVWR). Maintaining a proper front and rear weight distribution ratio is necessary to provide proper braking performance.


Total vehicle reserve capacity is the difference between the GVWR and the weight of the vehicle with full fuel and passengers. It is the amount of weight that can be added to the vehicle before reaching theGVWR. Keep in mind that reserve capacity numbers are intended as a guide when selecting the amount of equipment or cargo the vehicle can carry. If you are unsure of the vehicle's front, rear, or total weight, go to a weigh station and weigh the vehicle. Your dealer can also help you with this.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (94,1)


9-94


Driving and Operating


The total vehicle reserve capacity for the vehicle can be found in the lower right corner of the Certification/Tire label as shown previously. See your dealer for additional advice and information about using a snow plow on the vehicle. Also, see Vehicle Load Limits on page 9‑16.


Emergency Roof Lamp Provisions Vehicles with the RPO VYU snow plow prep package also have an emergency roof lamp provision package, RPO TRW. Wiring for the emergency roof lamp is provided above the overhead console. See Auxiliary Roof-Mounted Lamp on page 6‑7 for switch location.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (1,1)


Vehicle Care


General Information


General Information . . . . . . . . . . 10-2
California Proposition


65 Warning . . . . . . . . . . . . . . . . . 10-3


California Perchlorate


Materials Requirements . . . . 10-3


Accessories and


Modifications . . . . . . . . . . . . . . . 10-3


Vehicle Checks Doing Your Own


Service Work . . . . . . . . . . . . . . . 10-4
Hood . . . . . . . . . . . . . . . . . . . . . . . . 10-5
Engine Compartment


Overview . . . . . . . . . . . . . . . . . . . 10-6
Engine Oil . . . . . . . . . . . . . . . . . . . 10-7
Engine Oil Life System . . . . . 10-10
Automatic Transmission


Fluid . . . . . . . . . . . . . . . . . . . . . . 10-11
Engine Air Cleaner/Filter . . . . 10-14
Cooling System . . . . . . . . . . . . 10-16
Engine Coolant . . . . . . . . . . . . . 10-17
Engine Overheating . . . . . . . . 10-21
Overheated Engine


Protection Operating Mode . . . . . . . . . . . 10-23


Engine Fan . . . . . . . . . . . . . . . . . 10-23
Power Steering Fluid . . . . . . . 10-24
Washer Fluid . . . . . . . . . . . . . . . 10-25
Brakes . . . . . . . . . . . . . . . . . . . . . 10-26
Brake Fluid . . . . . . . . . . . . . . . . . 10-27
Battery . . . . . . . . . . . . . . . . . . . . . 10-28
Four-Wheel Drive . . . . . . . . . . . 10-29
Front Axle . . . . . . . . . . . . . . . . . . 10-30
Rear Axle . . . . . . . . . . . . . . . . . . 10-31
Starter Switch Check . . . . . . . 10-32
Automatic Transmission Shift


Lock Control Function Check . . . . . . . . . . . . . . . . . . . . . 10-32


Ignition Transmission Lock


Check . . . . . . . . . . . . . . . . . . . . . 10-33


Park Brake and P (Park)


Mechanism Check . . . . . . . . 10-33


Wiper Blade


Replacement . . . . . . . . . . . . . . 10-34
Glass Replacement . . . . . . . . 10-35


Headlamp Aiming


Headlamp Aiming . . . . . . . . . . 10-35


Bulb Replacement


Bulb Replacement . . . . . . . . . . 10-37
Halogen Bulbs . . . . . . . . . . . . . . 10-37


Vehicle Care


10-1


Taillamps, Turn Signal,


Stoplamps, and Back-Up Lamps . . . . . . . . . . . . . . . . . . . . 10-38
License Plate Lamp . . . . . . . . 10-39
Replacement Bulbs . . . . . . . . . 10-39


Electrical System


Electrical System


Overload . . . . . . . . . . . . . . . . . . 10-40


Fuses and Circuit


Breakers . . . . . . . . . . . . . . . . . . 10-41


Engine Compartment Fuse


Block . . . . . . . . . . . . . . . . . . . . . 10-41


Instrument Panel Fuse


Block . . . . . . . . . . . . . . . . . . . . . 10-45


Wheels and Tires


Tires . . . . . . . . . . . . . . . . . . . . . . . . 10-49
Tire Sidewall Labeling . . . . . . 10-50
Tire Designations . . . . . . . . . . . 10-53
Tire Terminology and


Definitions . . . . . . . . . . . . . . . . 10-54
Tire Pressure . . . . . . . . . . . . . . . 10-57
Tire Pressure Monitor


System . . . . . . . . . . . . . . . . . . . 10-59


Tire Pressure Monitor


Operation . . . . . . . . . . . . . . . . . 10-60
Tire Inspection . . . . . . . . . . . . . . 10-63
Tire Rotation . . . . . . . . . . . . . . . 10-64


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (2,1)


10-2


Vehicle Care


General Information For service and parts needs, visit your dealer. You will receive genuine GM parts and GM-trained and supported service people.


Genuine GM parts have one of these marks:


When It Is Time for New


Tires . . . . . . . . . . . . . . . . . . . . . . 10-65
Buying New Tires . . . . . . . . . . . 10-66
Different Size Tires and


Wheels . . . . . . . . . . . . . . . . . . . 10-68


Uniform Tire Quality


Grading . . . . . . . . . . . . . . . . . . . 10-69


Wheel Alignment and Tire


Balance . . . . . . . . . . . . . . . . . . . 10-70
Wheel Replacement . . . . . . . . 10-71
Tire Chains . . . . . . . . . . . . . . . . . 10-72
If a Tire Goes Flat . . . . . . . . . . 10-73
Tire Changing . . . . . . . . . . . . . . 10-75
Secondary Latch System . . . 10-85
Full-Size Spare Tire . . . . . . . . 10-88


Jump Starting


Jump Starting . . . . . . . . . . . . . . 10-89


Towing


Towing the Vehicle . . . . . . . . . 10-93
Recreational Vehicle


Towing . . . . . . . . . . . . . . . . . . . . 10-93


Appearance Care


Exterior Care . . . . . . . . . . . . . . . 10-99
Interior Care . . . . . . . . . . . . . . . 10-102
Floor Mats . . . . . . . . . . . . . . . . 10-105


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (3,1)


California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.


California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, safety belt pretensioners, and lithium batteries contained in Remote Keyless Entry transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/ perchlorate.


Vehicle Care


10-3


Accessories and Modifications Adding non‐dealer accessories or making modifications to the vehicle can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control, and stability control. These accessories or modifications could even cause malfunction or damage not covered by the vehicle warranty.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (4,1)


10-4


Vehicle Care


Damage to vehicle components resulting from modifications or the installation or use of non‐GM certified parts, including control module or software modifications, is not covered under the terms of the vehicle warranty and may affect remaining warranty coverage for affected parts. GM Accessories are designed to complement and function with other systems on the vehicle. See your dealer to accessorize the vehicle using genuine GM Accessories installed by a dealer technician. Also, see Adding Equipment to the Airbag-Equipped Vehicle on page 3‑44.


Vehicle Checks


Doing Your Own Service Work If the vehicle is a hybrid, see the hybrid supplement for more information.


{ WARNING


It can be dangerous to work on your vehicle if you do not have the proper knowledge, service manual, tools, or parts. Always follow owner manual procedures and consult the service manual for your vehicle before doing any service work.


If doing some of your own service work, use the proper service manual. It tells you much more about how to service the vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 13‑18. This vehicle has an airbag system. Before attempting to do your own service work, see Airbag System Check on page 3‑46. Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Records on page 11‑15.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (5,1)


Hood To open the hood:


1. Pull the handle with this symbol


on it. It is located inside the vehicle to the lower left of the steering wheel.


2. Then go to the front of the


vehicle and locate the secondary hood release, near the center of the grille.


Vehicle Care


10-5


3. Push the secondary hood


release to the right.


4. Lift the hood.


Before closing the hood, be sure all the filler caps are on properly. Then bring the hood from full open to within 152 mm (6 in) from the closed position, pause, then push the front center of the hood with a swift, firm motion to fully close the hood.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (6,1)


10-6


Vehicle Care


Engine Compartment Overview


5.3L V8 Engine Shown, 6.0L V8 Engine Similar


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (7,1)


Engine Cooling Fan (Out of View). See Cooling System on page 10‑16.


J. Power Steering Fluid Reservoir.


See Power Steering Fluid on page 10‑24.


K. Brake Master Cylinder


Reservoir. See “Brake Fluid” under Brake Fluid on page 10‑27.


L. Engine Compartment Fuse


Block on page 10‑41.


M. Windshield Washer Fluid


Reservoir. See “Adding Washer Fluid” under Washer Fluid on page 10‑25.


If the vehicle is a hybrid, see the hybrid supplement for more information.


A. Engine Air Cleaner/Filter on


I.


page 10‑14.


B. Coolant Surge Tank and


Pressure Cap. See Cooling System on page 10‑16.


C. Remote Positive (+) Terminal.


See Jump Starting on page 10‑89.


D. Battery on page 10‑28. E. Remote Negative (−) Terminal


(Out of View). See Jump Starting on page 10‑89. F. Automatic Transmission


Dipstick (Out of View). See “Checking the Fluid Level” under Automatic Transmission Fluid on page 10‑11.


G. Engine Oil Fill Cap. See “When


to Add Engine Oil” under Engine Oil on page 10‑7.


H. Engine Oil Dipstick (Out of


View). See “Checking Engine Oil” under Engine Oil on page 10‑7.


Vehicle Care


10-7


Engine Oil To ensure proper engine performance and long life, careful attention must be paid to engine oil. Following these simple, but important steps will help protect your investment: . Always use engine oil approved to the proper specification and of the proper viscosity grade. See “Selecting the Right Engine Oil” in this section.


. Check the engine oil level regularly and maintain the proper oil level. See “Checking Engine Oil” and “When to Add Engine Oil” in this section.


. Change the engine oil at the


appropriate time. See Engine Oil Life System on page 10‑10. . Always dispose of engine oil


properly. See “What to Do with Used Oil” in this section.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (8,1)


10-8


Vehicle Care


Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 10‑6 for the location of the engine oil dipstick. Obtaining an accurate oil level reading is essential: 1.


If the engine has been running recently, turn off the engine and allow several minutes for the oil to drain back into the oil pan. Checking the oil level too soon after engine shutoff will not provide an accurate oil level reading.


2. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level.


When to Add Engine Oil


If the oil is below the cross-hatched area at the tip of the dipstick, add 1 L (1 qt) of the recommended oil and then recheck the level. See “Selecting the Right Engine Oil” in this section for an explanation of what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 12‑2.


Notice: Do not add too much oil. Oil levels above or below the acceptable operating range shown on the dipstick are harmful to the engine. If you find that you have an oil level above the operating range, i.e., the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged. You should drain out the excess oil or limit driving of the vehicle and seek a service professional to remove the excess amount of oil. See Engine Compartment Overview on page 10‑6 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through.


Chevrolet Tahoe/Suburban Owner Manual - 2012 - 2nd - 11/9/11


Black plate (9,1)


Selecting the Right Engine Oil Selecting the right engine oil depends on both the proper oil specification and viscosity grade. See Recommended Fluids and Lubricants on page 11‑12.


Specification Use and ask for licensed engine oils with the dexos1™ approved certification mark. Engine oils meeting the requirements for the vehicle should have the dexos1
approved certification mark. This certification mark indicates that the oil has been approved to the dexos1
specification.


Notice: Failure to use the recommended engine oil or equivalent can result in engine damage not covered by the vehicle warranty. Check with your dealer or service provider on whether the oil is approved to the dexos1 specification.


Viscosity Grade SAE 5W‐30 is the best viscosity grade for the vehicle. Do not use other viscosity grade oils such as SAE 10W‐30, 10W‐40, or 20W‐50.


Vehicle Care


10-9


If in an area of extreme cold, where the temperature falls below −20°F (−29°C), an SAE 0W‐30 oil should be used. An oil of this viscosity grade will provide easier cold starting for the engine at extremely low temperatures. When selecting an oil of the appropriate viscosity grade, always select an oil that meets the dexos1 specification or equivalent. See “Specification” for more information. Engine Oil Additives/Engine Oil Flushes Do not add anything to the oil. The recommended oils with the dexos specification and displaying the dexos certification mark are all that is needed for good performance and engine protection.

Loading...
x