Download PDF Manual

6. Proceed to the passenger side front tire, and repeat


the procedure in Step 5.


7. Proceed to the passenger side rear tire, and repeat


the procedure in Step 5.


8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.


9. Turn the ignition switch to LOCK/OFF. 10. Set all four tires to the recommended air pressure


level as indicated on the Tire and Loading Information label.


11. Put the valve caps back on the valve stems.


Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, for signs of wear or damage. See When It Is Time for New Tires on page 5-77 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). See Scheduled Maintenance on page 6-4.


5-75


The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle. This will ensure that your vehicle continues to perform most like it did when the tires were new. Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-77
and Wheel Replacement on page 5-82.


After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. See Inflation - Tire Pressure on page 5-70 and Loading Your Vehicle on page 4-35. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 5-73. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 5-124.


{CAUTION:


Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See Changing a Flat Tire on page 5-86.


When rotating your vehicle’s tires, always use the correct rotation pattern shown here. Do not include the spare tire in the tire rotation.


5-76


Make sure the spare tire is stored securely. Push, pull, and then try to rotate or turn the tire. If it moves, tighten the cable. See Storing a Flat or Spare Tire and Tools on page 5-102.


When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions, influence when you need new tires.


One way to tell when it is time for new tires is to check the treadwear indicators, which appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. Some commercial truck tires may not have treadwear indicators.


You need new tires if any of the following statements are true: (cid:129) You can see the indicators at three or more places


around the tire.


(cid:129) You can see cord or fabric showing through the


tire’s rubber. The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric. The tire has a bump, bulge, or split. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.


The rubber in tires degrades over time, even if they are not being used. This is also true for the spare tire, if your vehicle has one. Multiple conditions affect how fast this aging takes place, including temperatures, loading conditions, and inflation pressure maintenance. With proper care and maintenance tires will typically wear out before they degrade due to age. If you are unsure about the need to replace your tires as they get older, consult the tire manufacturer for more information.


5-77


(cid:129) (cid:129) (cid:129) {CAUTION:


Mixing tires could cause you to lose control while driving. If you mix tires of different sizes, brands, or types (radial and bias-belted tires), the vehicle might not handle properly, and you could have a crash. Using tires of different sizes, brands, or types could also cause damage to your vehicle. Be sure to use the same size, brand, and type tires on all wheels. Your vehicle may have a different size spare than the road tires (those originally installed on your vehicle). When new, your vehicle included a spare tire and wheel assembly with a similar overall diameter as your vehicle’s road tires and wheels, so it is all right to drive on it. Because this spare was developed for use on your vehicle, it will not affect vehicle handling.


Buying New Tires GM has developed and matched specific tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Specification (TPC spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating. This way, your vehicle will continue to have tires that are designed to give the same performance and vehicle safety, during normal use, as the original tires. GM’s exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of your vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM’s TPC Spec number is molded onto the tire’s sidewall near the tire size. If the tires have an all-season tread design, the TPC spec number will be followed by an MS for mud and snow. See Tire Sidewall Labeling on page 5-64 for additional information. GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle. See Tire Inspection and Rotation on page 5-75 for information on proper tire rotation.


5-78


{CAUTION:


If you use bias-ply tires on your vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle.


If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction type (radial and bias-belted tires) as your vehicle’s original tires.


Vehicles that have a tire pressure monitoring system may give an inaccurate low-pressure warning if non-TPC spec rated tires are installed on your vehicle. Non-TPC Spec rated tires may give a low-pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires. See Tire Pressure Monitor System on page 5-71. Your vehicle’s original equipment tires are listed on the Tire and Loading Information Label. See Loading Your Vehicle on page 4-35, for more information about the Tire and Loading Information Label and its location on your vehicle.


5-79


Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this could affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover. Additionally, if your vehicle has electronic systems such as anti-lock brakes, rollover airbags, traction control, and electronic stability control, the performance of these systems can be affected.


{CAUTION:


If you add different sized wheels, your vehicle may not provide an acceptable level of performance and safety if tires not recommended for those wheels are selected. You may increase the chance that you will crash and suffer serious injury. Only use GM specific wheel and tire systems developed for your vehicle, and have them properly installed by a GM certified technician.


See Buying New Tires on page 5-78 and Accessories and Modifications on page 5-3 for additional information.


5-80


Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards.


Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.


Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


5-81


Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment might need to be checked. If you notice your vehicle vibrating when driving on a smooth road, the tires and wheels might need to be rebalanced. See your dealer/retailer for proper diagnosis.


Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer/retailer if any of these conditions exist. Your dealer/retailer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, wheel nuts, and TPMS sensors for your vehicle.


5-82


Used Replacement Wheels


{CAUTION:


Putting a used wheel on your vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.


{CAUTION:


Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.


Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See Changing a Flat Tire on page 5-86 for more information.


5-83


Tire Chains If your vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information.


{CAUTION:


If your vehicle has P265/65R18 or P275/55R20
size tires, do not use tire chains. They can damage your vehicle because there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions.


CAUTION:


(Continued)


CAUTION:


(Continued)


To help avoid damage to your vehicle, drive slowly, readjust or remove the device if it is contacting your vehicle, and do not spin your vehicle’s wheels. If you do find traction devices that will fit, install them on the rear tires.


If your vehicle has P265/70R17 size tires,


Notice: use tire chains only where legal and only when you must. Use chains that are the proper size for your vehicle’s tires. Install them on the rear tires only. Do not use chains on the front tires. Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.


5-84


If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop well out of the traffic lane. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop, well off the road if possible.


{CAUTION:


Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. Use the jack provided with your vehicle only for changing a flat tire.


If a tire goes flat, the next part shows how to use the jacking equipment to change a flat tire safely.


5-85


CAUTION:


(Continued)


3. If you have a four-wheel-drive vehicle, be sure the transfer case is in a drive gear — not in NEUTRAL.


4. Turn off the engine and do not restart


while the vehicle is raised.


5. Do not allow passengers to remain in the


vehicle.


6. Put the wheel blocks at the front and rear


of the tire farthest away from the one being changed. That would be the tire on the other side, at the opposite end of the vehicle.


Changing a Flat Tire If your vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers. See Hazard Warning Flashers on page 3-6 for more information.


{CAUTION:


Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving:


1. Set the parking brake firmly. 2. Put the shift lever in PARK (P).


CAUTION:


(Continued)


5-86


When your vehicle has a flat tire, use this as a guide to assist you in the placement of wheel blocks.


Removing the Spare Tire and Tools The equipment you will need to change a flat tire is stored under the storage tray, which is located on the driver side trim panel (over the rear wheelhouse).


Regular Wheelbase shown, Extended Wheelbase similar.


1. Remove the tray to access the tools by pulling up


on the finger depression under the jack symbol.


5-87


2. Remove the wing nut (B) used to retain the tool bag


by turning it counterclockwise.


3. Turn the knob (A) on the jack counterclockwise to


release the jack and wheel blocks from the bracket.


4. Remove the wheel blocks and the wheel block


retainer by turning the wing nut (C) counterclockwise.


The tools you will be using include the following:


A. Jack B. Wheel Blocks C. Jack Handle


D. Jack Handle


Extensions


E. Wheel Wrench


5-88


To access the spare tire, refer to the following graphics and instructions:


G. Tire/Wheel Retainer H. Spare Tire (Valve


J. Hoist End of


Extension Tool


Stem Pointed Down)


K. Spare Tire Lock


I. Hoist Shaft Access


Hole


1. Open the hoist shaft access door (C) on the


bumper to access the spare tire lock (K).


2. To remove the spare tire lock, insert the ignition key, turn it clockwise and then pull it straight out.


A. Hoist Assembly B. Hoist Shaft C. Hoist Shaft Access


Cover/Hole


D. Jack Handle


Extensions


E. Wheel Wrench F. Hoist Cable


3. Assemble the two jack handle extensions (D) and


wheel wrench (E) as shown.


5-89


4. Insert the open end of


the extension (J) through the hole in the rear bumper (I) (hoist shaft access hole).


6. Use the wheel wrench hook that allows you to pull the hoist cable towards you, to assist in reaching the spare tire.


Be sure the hoist end (J) of the extension (D) connects to the hoist shaft (B). The ribbed square end of the extension is used to lower the spare tire.


5. Turn the wheel wrench (E) counterclockwise to


lower the spare tire (H) to the ground. Continue to turn the wheel wrench until the spare tire can be pulled out from under the vehicle. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower. See Secondary Latch System on page 5-98
for more information.


5-90


Once the retainer is separated from the guide pin, tilt the retainer and pull it through the center of the wheel along with the cable and latch.


8. Put the spare tire near the flat tire.


7. Tilt the tire toward the vehicle with some slack in


the cable to access the tire/wheel retainer. Separate the retainer from the guide pin by sliding the retainer up the pin while pressing down on the latch.


5-91


Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing


a Flat Tire on page 5-86 for more information.


2. If your vehicle has a center cap place the chisel end of the wheel wrench in the slot on the wheel and gently pry the cap out. If the wheel has a bolt-on hub cap, loosen the plastic nut caps by turning the wheel wrench counterclockwise. The plastic nut caps will be retained in the hub cap after it is removed from the wheel.


5-92


3. Use the wheel wrench to loosen all the wheel nuts. Turn the wheel wrench counterclockwise to loosen the wheel nuts. Do not remove the wheel nuts yet.


Jacking Locations (Overall View)


A. Front Position B. Rear Position


4. Position the jack under the vehicle as shown.


Front Position


Front Tire Flat: If the flat tire is on a front tire of the vehicle, you will need to use the jack handle and only one jack handle extension. Attach the wheel wrench to the jack handle extension. Attach the jack handle to the jack (A). Position the jack on the frame behind the flat tire where the frame sections overlap. Turn the wheel wrench clockwise to raise the vehicle. Raise the vehicle far enough off the ground so there is enough room for the spare tire to clear the ground.


5-93


Rear Position – 1500 Models


Rear Position – All Other Models


Rear Tire Flat: If the flat tire is on a rear tire of the vehicle, you will need to use the jack handle (B) and both jack handle extensions (C). Attach the wheel wrench (D) to the jack handle extensions (C). Attach the jack handle (B) to the jack (A). Use the jacking pad provided on the rear axle. Turn the wheel wrench (D) clockwise to raise the vehicle. Raise the vehicle far enough off the ground so there is enough room for the spare tire to clear the ground.


5-94


5. Remove all of the


wheel nuts.


{CAUTION:


Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.


{CAUTION:


Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.


6. Take off the flat tire.


5-95


7. Remove any rust or dirt


from the wheel bolts, mounting surfaces, and spare wheel.


8. Put the wheel nuts back on with the rounded end


of the nuts toward the wheel after mounting the spare tire.


{CAUTION:


Never use oil or grease on studs or nuts. Because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash.


9. Tighten each wheel nut by hand. Then use the wheel wrench to tighten the nuts until the wheel is held against the hub.


10. Turn the wheel wrench counterclockwise to lower


the vehicle. Lower the jack completely.


11. Tighten the nuts firmly in a crisscross sequence as


shown by turning the wheel wrench clockwise.


{CAUTION:


Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See Changing a Flat Tire on page 5-86.


5-96


Improperly tightened wheel nuts can lead


Notice: to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 5-124 for the wheel nut torque specification. When you reinstall the regular wheel and tire, you must also reinstall either the center cap or the bolt-on hub cap, depending on which your vehicle has.


For center caps, line up the tab on the center cap with the slot in the wheel. The cap only goes in one way. Place the cap on the wheel and press until it snaps into place. For bolt-on hub caps, line up the plastic nut caps with the wheel nuts and tighten clockwise by hand to get them started. Then tighten with the wheel wrench until snug.


5-97


{CAUTION:


Incorrect or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to a crash. If you have to replace them, be sure to get new original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification. See Capacities and Specifications on page 5-124 for wheel nut torque specification.


(cid:129) (cid:129) Secondary Latch System Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire from suddenly falling off your vehicle. For the secondary latch to work, the spare must be installed with the valve stem pointing down. See Storing a Flat or Spare Tire and Tools on page 5-102.


{CAUTION:


Before beginning this procedure read all the instructions. Failure to read and follow the instructions could damage the hoist assembly and you and others could get hurt. Read and follow the instructions listed next.


To release the spare tire from the secondary latch:


1. Check under the


vehicle to see if the cable end is visible. If the cable is not visible proceed to Step 6.


2. If it is visible, first try to tighten the cable by turning


the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot overtighten the cable.


5-98


3. Loosen the cable by turning the wrench


counterclockwise three or four turns.


6. Stand the wheel blocks on their shortest ends, with


the backs facing each other.


4. Repeat this procedure at least two times. If the


spare tire lowers to the ground, continue with Step 5 of Removing the Spare Tire and Tools on page 5-87.


5. If the spare does not lower, turn the wrench


counterclockwise until approximately 6 inches (15 cm) of cable is exposed.


7. Place the bottom edge


of the jack (A) on the wheel blocks (B), separating them so that the jack is balanced securely.


5-99


8. Attach the jack handle, extension, and wheel wrench to the jack and place it (with the wheel blocks) under the vehicle toward the front of the rear bumper.


9. Position the center lift point of the jack under the


center of the spare tire.


10. Turn the wrench clockwise to raise the jack until it


lifts the end fitting.


11. Continue raising the jack until the spare tire stops


moving upward and is held firmly in place. The secondary latch has released and the spare tire is balancing on the jack.


5-100


12. Lower the jack by turning the wheel wrench


counterclockwise. Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable.


{CAUTION:


Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely, make sure no one is behind you or on either side of you as you pull the jack out from under the spare.


13. Disconnect the jack handle from the jack and


carefully remove the jack. Use one hand to push against the spare while firmly pulling the jack out from under the spare tire with the other hand. If the spare tire is hanging from the cable, insert the hoist end of extension, and wheel wrench into the hoist shaft hole in the bumper and turn the wheel wrench counterclockwise to lower the spare the rest of the way.


14. Tilt the tire retainer at the end of the cable and pull it through the wheel opening. Pull the tire out from under the vehicle.


15. Turn the wheel wrench in the hoist shaft hole in the bumper clockwise to raise the cable back up if the cable is hanging under the vehicle.


Have the hoist assembly inspected as soon as you can. You will not be able to store a spare or flat tire using the hoist assembly until it has been replaced. To continue changing the flat tire, see Removing the Flat Tire and Installing the Spare Tire on page 5-92.


5-101


Storing a Flat or Spare Tire and Tools


Store the tire under the rear of the vehicle in the spare tire carrier. Refer to the following graphics and instructions to help you:


{CAUTION:


Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.


Notice: Storing an aluminum wheel with a flat tire under your vehicle for an extended period of time or with the valve stem pointing up can damage the wheel. Always stow the wheel with the valve stem pointing down and have the wheel/tire repaired as soon as possible.


5-102


A. Hoist Assembly B. Hoist Shaft C. Hoist Shaft Access


Cover/Hole


D. Jack Handle


Extensions


E. Wheel Wrench F. Hoist Cable


G. Tire/Wheel Retainer H. Spare Tire/Flat Tire


I. Hoist Shaft Access Hole J. Hoist End of


(Valve Stem Pointed Down)


Extension Tool


K. Spare Tire Lock


1. Put the tire (H) on the ground at the rear of the


vehicle with the valve stem pointed down, and to the rear.


2. Tilt the tire toward the vehicle. Separate the


tire/wheel retainer (D) from the guide pin. Pull the pin through the center of the wheel. Tilt the retainer down through the center wheel opening. Make sure the retainer is fully seated across the underside of the wheel.


3. Assemble the two jack handle extensions (D) and


wheel wrench (E) as shown.


4. Insert the open end of


the extension (J) through the hole in the rear bumper (I) (hoist shaft access hole).


5. Raise the tire part way upward. Make sure the


retainer is seated in the wheel opening.


5-103


6. Raise the tire fully against the underside of the vehicle by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot overtighten the cable.


To store the tools, do the following.


A. Wheel Blocks B. Tool Bag with


Jack Tools


C. Retaining Bracket D. Wing Nut Retaining


Tool Bag


E. Jack F. Wing Nut Retaining


Wheel Blocks


G. Wing Nut on Jack


7. Make sure the tire is stored securely. Push, pull (A),


and then try to turn (B) the tire. If the tire moves, use the wheel wrench to tighten the cable.


8. Reinstall the spare tire lock. 9. Reinstall the hoist shaft access cover.


5-104


1. Return the tools (wheel wrench, jack handle, and


jack handle extensions) to the tool bag (B).


2. Assemble wheel blocks (A) and jack (E) together


with the wing nut (F).


3. Position the jack (E) and wheel blocks (A) in the


driver’s side trim panel over the wheelhouse.


4. Turn the wing nut (G) clockwise until the jack is


secured tight in the mounting bracket. Be sure to position the holes in the base of the jack onto the pin in the mounting bracket.


5. Use the retaining bracket (C) to fasten the tool


bag (B) on the stud and turn the wing nut (D) clockwise to secure.


6. Return the storage tray to its original stored


position.


5-105


If your vehicle has four-wheel drive and the


Spare Tire Your vehicle, when new, had a fully-inflated spare tire. A spare tire may lose air over time, so check its inflation pressure regularly. See Inflation - Tire Pressure on page 5-70 and Loading Your Vehicle on page 4-35
for information regarding proper tire inflation and loading your vehicle. For instruction on how to remove, install or store a spare tire, see Removing the Flat Tire and Installing the Spare Tire on page 5-92 and Storing a Flat or Spare Tire and Tools on page 5-102. Notice: different size spare tire is installed on your vehicle, do not drive in four-wheel drive until you can have your flat tire repaired and/or replaced. You could damage your vehicle, and the repair costs would not be covered by your warranty. Never use four-wheel drive when the different size spare tire is installed on your vehicle. Your vehicle may have a different size spare tire than the road tires originally installed on your vehicle. This spare tire was developed for use on your vehicle, so it is all right to drive on it. If your vehicle has four-wheel drive and the different size spare tire is installed, keep the vehicle in two-wheel drive.


After installing the spare tire on your vehicle, you should stop as soon as possible and make sure the spare tire is correctly inflated. Have the damaged or flat road tire repaired or replaced as soon as you can and installed back onto your vehicle. This way, the spare tire will be available in case you need it again. Do not mix tires and wheels of different sizes, because they will not fit. Keep your spare tire and its wheel together. If your vehicle has a spare tire that does not match your vehicle’s original road tires and wheels in size and type, do not include the spare in the tire rotation. Appearance Care


Interior Cleaning Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery. It is important to keep your upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible. Your vehicle’s interior may experience extremes of heat that could cause stains to set rapidly.


5-106


Lighter colored interiors may require more frequent cleaning. Use care because newspapers and garments that transfer color to your home furnishings may also transfer color to your vehicle’s interior. When cleaning your vehicle’s interior, only use cleaners specifically designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately. To prevent over-spray, apply cleaner directly to the cleaning cloth. Notice: glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the rear window defogger. When cleaning the glass on your vehicle, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in your vehicle’s breathing space. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning your vehicle’s interior, maintain adequate ventilation by opening your vehicle’s doors and windows. Dust may be removed from small buttons and knobs using a small brush with soft bristles.


If you use abrasive cleaners when cleaning


Your dealer/retailer has a product for cleaning your vehicle’s glass. Should it become necessary, you can also obtain a product from your dealer/retailer to remove odors from your vehicle’s upholstery. Do not clean your vehicle using the following cleaners or techniques: (cid:129) Never use a knife or any other sharp object to


remove a soil from any interior surface.


(cid:129) Never use a stiff brush. It can cause damage to


your vehicle’s interior surfaces.


(cid:129) Never apply heavy pressure or rub aggressively with a cleaning cloth. Use of heavy pressure can damage your interior and does not improve the effectiveness of soil removal.


(cid:129) Use only mild, neutral-pH soaps. Avoid laundry


detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide.


(cid:129) Do not heavily saturate your upholstery while


cleaning.


(cid:129) Damage to your vehicle’s interior may result from the


use of many organic solvents such as naptha, alcohol, etc.


5-107


Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda. Before cleaning, gently remove as much of the soil as possible using one of the following techniques:


For liquids: gently blot the remaining soil with a paper towel. Allow the soil to absorb into the paper towel until no more can be removed. For solid dry soils: remove as much as possible and then vacuum.


To clean, use the following instructions: 1. Saturate a lint-free, clean white cloth with water or


club soda.


2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled. 4. Continue to gently rub the soiled area until the


cleaning cloth remains clean.


5. If the soil is not completely removed, use a mild


soap solution and repeat the cleaning process that was used with plain water.


5-108


If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. After the cleaning process has been completed, a paper towel can be used to blot excess moisture from the fabric or carpet.


Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather. Never use spot lifters or spot removers on leather. Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of your leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Never use shoe polish on leather.


(cid:129) (cid:129) Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of your interior and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Some commercial products may increase gloss on your instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions.


Care of Safety Belts Keep belts clean and dry.


{CAUTION:


Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.


Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 6-13.


5-109


Washing Your Vehicle The best way to preserve your vehicle’s finish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on your vehicle. Check the cleaning product label. If it states that it should not be used on plastic parts, do not use it on your vehicle or damage may occur and it would not be covered by the warranty. Do not wash the vehicle in direct sunlight. Use a car washing soap. Do not use cleaning agents that are petroleum based or that contain acid or abrasives, as they can damage the paint, metal or plastic on your vehicle. Approved cleaning products can be obtained from your dealer/retailer. See Vehicle Care/Appearance Materials on page 5-114. Follow all manufacturers’ directions regarding correct product usage, necessary safety precautions and appropriate disposal of any vehicle care product. Rinse the vehicle well, before washing and after to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting.


High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the vehicle. Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.


Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 5-110.


Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get approved cleaning products from your dealer/retailer. See Vehicle Care/Appearance Materials on page 5-114. If your vehicle has a basecoat/clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish.


5-110


Windshield, Backglass, and Wiper Blades Clean the outside of the windshield and backglass with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when you clean the blades. Bugs, road grime, sap and a buildup of vehicle wash/wax treatments may cause wiper streaking. Replace the wiper blades if they are worn or damaged. Wipers can be damaged by: (cid:129) Extreme dusty conditions (cid:129) Sand and salt (cid:129) Heat and sun (cid:129) Snow and ice, without proper removal


Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible. Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, you may use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts.


5-111


Aluminum or Chrome-Plated Wheels and Trim Your vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. Notice: Chrome wheels and other chrome trim may be damaged if you do not wash your vehicle after driving on roads that have been sprayed with magnesium, calcium or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash your vehicle’s chrome with soap and water after exposure. Notice: abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by your warranty. Use only approved cleaners on aluminum or chrome-plated wheels.


If you use strong soaps, chemicals,


The surface of these wheels is similar to the painted surface of your vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels. Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only. Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application. Notice: automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum or chrome-plated wheels. The repairs would not be covered by your warranty. Never drive a vehicle equipped with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes.


If you drive your vehicle through an


5-112


Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.


Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.


Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer/retailer. Larger areas of finish damage can be corrected in your dealer’s/retailer’s body and paint shop.


Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer/retailer or an underbody car washing system can do this for you.


5-113


Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, we will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.


Vehicle Care/Appearance Materials


Description


Usage


Polishing Cloth


Tar and Road Oil Remover Chrome Cleaner and Polish


White Sidewall Tire Cleaner


Vinyl Cleaner


Glass Cleaner


Chrome Wheel Cleaner


Finish Enhancer


Interior and exterior polishing cloth. Removes tar, road oil, and asphalt. Use on chrome or stainless steel. Removes soil and black marks from whitewalls and raised white lettering. Cleans vinyl. Removes dirt, grime, smoke and fingerprints. Removes dirt and grime from chrome wheels. Removes dust, fingerprints, and surface contaminants. Spray on and wipe off.


5-114


Description


Usage


Vehicle Identification


Swirl Remover Polish


Cleaner Wax


Foaming Tire Shine Low Gloss


Wash Wax Concentrate


Spot Lifter


Odor Eliminator


Removes swirl marks, fine scratches, and other light surface contamination. Removes light scratches and protects finish. Cleans, shines, and protects tires. No wiping necessary. Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free. Quickly removes spots and stains from carpets, vinyl, and cloth upholstery. Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet.


Vehicle Identification Number (VIN)


This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Certification/Tire and Service Parts labels and the certificates of title and registration. Engine Identification The eighth character in the VIN is the engine code. This code helps you identify your vehicle’s engine, specifications, and replacement parts. See Capacities and Specifications on page 5-124 for your vehicle’s engine code.


5-115


Service Parts Identification Label This label is on the inside of the glove box. It is very helpful if you ever need to order parts. The label has the following information: (cid:129) Vehicle Identification Number (VIN) (cid:129) Model designation (cid:129) Paint information (cid:129) Production options and special equipment Do not remove this label from the vehicle.


Electrical System


Add-On Electrical Equipment If your vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. Notice: Do not add anything electrical to your vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain your vehicle’s battery, even if your vehicle is not operating. Your vehicle has an airbag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Airbag-Equipped Vehicle on page 1-90.


5-116


Windshield Wiper Fuses The windshield wiper motor is protected by an internal circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem and not snow, etc., be sure to get it fixed.


Power Windows and Other Power Options Circuit breakers protect the power windows and other power accessories. If the current load is too heavy, the circuit breaker opens and then closes after a cool down period, protecting the circuit until the problem is fixed or goes away.


Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating. If you ever have a problem on the road and don’t have a spare fuse, you can borrow one that has the same amperage. Just pick some feature of your vehicle that you can get along without – like the radio or cigarette lighter – and use its fuse, if it is the correct amperage. Replace it as soon as you can.


5-117


Instrument Panel Fuse Block The instrument panel fuse block access door is located on the driver side edge of the instrument panel.


Fuses


Usage


Rear Seats rear Accessory Power Outlet Steering Wheel Controls Backlight Driver Door Module Dome Lamps, Driver Side Turn Signal Driver Side Turn Signal, Stoplamp


5-118


Fuses


Usage


10
11


12


13
14
15
16
17
18
19


20


21
22
23
24


25


26


Instrument Panel Back Lighting Passenger Side Turn Signal, Stoplamp Passenger Door Module, Universal Home Remote System Power Door Lock 2 (Unlock Feature) Power Door Lock 2 (Lock Feature) Stoplamps, Center-High Mounted Stoplamp Rear Climate Controls Not Used Body Control Module (BCM) Accessory Power Outlets Interior Lamps Power Door Lock 1 (Unlock Feature) Rear Seat Entertainment Ultrasonic Rear Parking Assist, Power Liftgate Power Door Lock 1 (Lock Feature) Driver Information Center (DIC) Rear Wiper Not Used Driver Seat Module, Remote Keyless Entry System Not Used


Harness Connector


LT DR BODY BODY


Usage


Driver Door Harness Connection Harness Connector Harness Connector


Center Instrument Panel Fuse Block The center instrument panel fuse block is located underneath the instrument panel, to the left of the steering column. Top View


Harness Connector


BODY 2
BODY 1
BODY 3


Usage


Body Harness Connector 2
Body Harness Connector 1
Body Harness Connector 3


HEADLINER 3 Headliner Harness Connector 3
HEADLINER 2 Headliner Harness Connector 2
HEADLINER 1 Headliner Harness Connector 1
SEO/UPFITTER Special Equipment Option Upfitter


Harness Connector


Circuit Breaker


Usage


CB1


CB2
CB3
CB4


Passenger Side Power Window Circuit Breaker Passenger Seat Circuit Breaker Driver Seat Circuit Breaker Rear Sliding Window


5-119


Underhood Fuse Block


The underhood fuse block is located in the engine compartment, on the driver side of the vehicle. Lift the cover for access to the fuse/relay block. Notice: Spilling liquid on any electrical components on your vehicle may damage it. Always keep the covers on any electrical component. To remove fuses, hold the end of the fuse between your thumb and index finger and pull straight out.


5-120


Fuses


Usage


Right Trailer Stop/Turn Lamp Electronic Stability Suspension Control, Automatic Level Control Exhaust Left Trailer Stop/Turn Lamp Engine Controls Engine Control Module, Throttle Control


Fuses


Usage


Fuses


Usage


10
11
12


13


14


Trailer Brake Controller Front Washer Oxygen Sensors Antilock Brakes System 2
Trailer Back-up Lamps Driver Side Low-Beam Headlamp Engine Control Module (Battery) Fuel Injectors, Ignition Coils (Right Side) Transmission Control Module (Battery)


15


16


17
18
19
20
21
22
23


24


25
26
27
28


Vehicle Back-up Lamps Passenger Side Low-Beam Headlamp Air Conditioning Compressor Oxygen Sensors Transmission Controls (Ignition) Fuel Pump Fuel System Control Module Headlamp Washer Rear Windshield Washer Fuel Injectors, Ignition Coils (Left Side) Trailer Park Lamps Driver Side Park Lamps Passenger Side Park Lamps Fog Lamps


5-121


Fuses


Usage


Fuses


Usage


29


30


31
32
33
34


35


36
37
38
39
40
41
42


43


Horn Passenger Side High-Beam Headlamp Daytime Running Lamps (DRL) Driver Side High-Beam Headlamp Daytime Running Lamps 2
Sunroof Key Ignition System, Theft Deterrent System Windshield Wiper SEO B2 Upfitter Usage (Battery) Electric Adjustable Pedals Climate Controls (Battery) Airbag System (Ignition) Amplifier Audio System Miscellaneous (Ignition), Cruise Control


44
45
46
47


48


49


50
51
52


53


54


55


56


Liftgate Release Airbag System (Battery) Instrument Panel Cluster Power Take-Off Auxiliary Climate Control (Ignition), Compass-Temperature Mirror Center High-Mounted Stoplamp (CHMSL) Rear Defogger Heated Mirrors SEO B1 Upfitter Usage (Battery) Cigarette Lighter, Auxiliary Power Outlet Automatic Level Control Compressor Relay, SEO Upfitter Usage Climate Controls (Ignition) Engine Control Module, Secondary Fuel Pump (Ignition)


5-122


J-Case Fuses


Usage


Relays


Usage


60
61
62
63
64
65
66
67


68


69
70
71
72


Cooling Fan 1
Antilock Brake System 1
Starter Stud 2 (Trailer Brakes) Left Bussed Electrical Center 1
Electric Running Boards Heated Windshield Washer System Four-Wheel Drive System Stud 1 (Trailer Connector Battery Power) Mid-Bussed Electrical Center 1
Climate Control Blower Power Liftgate Module Left Bussed Electrical Center 2


Cooling Fan High Speed Cooling Fan Low Speed


FAN HI FAN LO ENG EXH VLV Not Used Cooling Fan Control FAN CNTRL Low-Beam Headlamp HDLP LO/HID Front Fog Lamps FOG LAMP Air Conditioning Compressor A/C CMPRSR Starter STRTR Powertrain PWR/TRN Fuel Pump FUEL PMP PRK LAMP Parking Lamps REAR DEFOG Rear Defogger RUN/CRANK


Switched Power


5-123


Capacities and Specifications If your vehicle is a Two-mode Hybrid, see the Two-mode Hybrid manual for more information. The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-13 for more information.


Application


Air Conditioning Refrigerant R134a


Capacities


English


Metric


For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood. See your dealer/retailer for more


information.


Cooling System


4.8L V8
5.3L V8
6.0L V8 1500 Series 6.0L V8 2500 Series


Engine Oil with Filter Fuel Tank Regular Extended 1500 Series Extended 2500 Series


5-124


17.8 qt 18.3 qt 17.9 qt 17.4 qt 6.0 qt†


26.0 gal 31.5 gal 39.0 gal


16.9 L 17.3 L 16.9 L 16.5 L 5.7 L†


98.4 L 119.2 L 147.6 L


Application


Transmission Fluid


4L70-E Super Duty Transmission and 4L60-E Electronic Transmission 4L80-E Transmission 6L90-Transmission


Transfer Case Fluid Wheel Nut Torque


English


5.0 qt


7.7 qt 6.3 qt 2.0 qt 140 lb ft


Capacities


Metric


4.7 L


7.3 L 6.0 L 1.9 L


190 Y


†Oil filter should be changed at every oil change. After refill, the level must be rechecked. Add enough engine coolant so that the fluid is within the proper operating range.


5-125


Engine Specifications


Engine 4.8L V8


5.3L V8 Flexible Fuel with Active Fuel Management™


(Iron Block)


5.3L V8 Flexible Fuel with Active Fuel Management™


(Aluminum Block)


5.3L V8 with Active Fuel


Management™ (Iron Block)


6.0L V8 (Iron Block) 6.0L V8 with Active Fuel Management™


(Aluminum Block)


VIN Code


Transmission


Automatic


Spark Plug Gap 0.040 in (1.01 mm)


Automatic


0.040 in (1.01 mm)


Automatic


0.040 in (1.01 mm)


Automatic


Automatic


Automatic


0.040 in (1.01 mm)


0.040 in (1.01 mm)


0.040 in (1.01 mm)


5-126


Section 6


Maintenance Schedule


Maintenance Schedule ......................................6-2
Introduction ...................................................6-2
Maintenance Requirements ..............................6-2
Your Vehicle and the Environment ....................6-2
Using the Maintenance Schedule ......................6-2
Scheduled Maintenance ...................................6-4
Additional Required Services ............................6-6
Maintenance Footnotes ...................................6-7


Owner Checks and Services ............................6-9
At Each Fuel Fill ............................................6-9
At Least Once a Month .................................6-10
At Least Once a Year ...................................6-10
Recommended Fluids and Lubricants ...............6-13
Maintenance Replacement Parts .....................6-15
Engine Drive Belt Routing ..............................6-16
Maintenance Record .....................................6-17


6-1


Maintenance Schedule


Introduction Important: Keep engine oil at the proper level and change as recommended.


Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer/retailer for details.


Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance might not be covered by warranty.


6-2


Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance is important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.


Using the Maintenance Schedule We want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather. You might use your vehicle in making deliveries. Or you might drive it to work, to do errands, or in many other ways. Because of all the different ways people use their vehicles, maintenance needs vary. You might need more frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your dealer/retailer.


This schedule is for vehicles that:


carry passengers and cargo within recommended limits. You will find these limits on the Tire and Loading Information label. See Loading Your Vehicle on page 4-35. are driven on reasonable road surfaces within legal driving limits. are driven off-road in the recommended manner. See Off-Road Driving on page 4-13. use the recommended fuel. See Gasoline Octane on page 5-5.


The services in Scheduled Maintenance on page 6-4
should be performed when indicated. See Additional Required Services on page 6-6 and Maintenance Footnotes on page 6-7 for further information.


{CAUTION:


Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment


CAUTION:


(Continued)


CAUTION:


(Continued)


for the job. If you have any doubt, see your dealer/retailer to have a qualified technician do the work. See Doing Your Own Service Work on page 5-4.


Some maintenance services can be complex. So, unless you are technically qualified and have the necessary equipment, you should have your dealer/retailer do these jobs. When you go to your dealer/retailer for your service needs, you will know that trained and supported service technicians will perform the work using genuine parts. If you want to purchase service information, see Service Publications Ordering Information on page 7-15. Owner Checks and Services on page 6-9 tells you what should be checked, when to check it, and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-13 and Maintenance Replacement Parts on page 6-15. When your vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. We recommend the use of genuine parts from your dealer/retailer.


6-3


(cid:129) (cid:129) (cid:129) (cid:129) Scheduled Maintenance When the CHANGE ENGINE OIL SOON message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year. However, your engine oil and filter must be changed at least once a year and at this time the system must be reset. Your dealer/retailer has trained service technicians who will perform this work using genuine parts and reset the system. If the engine oil life system is ever reset accidentally, you must service your vehicle within 3,000 miles (5 000 km) since your last service. Remember to reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 5-18 for information on the Engine Oil Life System and resetting the system.


When the CHANGE ENGINE OIL SOON message appears, certain services, checks, and inspections are required. Required services are described in the following for “Maintenance I” and “Maintenance II.” Generally, it is recommended that your first service be Maintenance I, your second service be Maintenance II, and that you alternate Maintenance I and Maintenance II thereafter. However, in some cases, Maintenance II may be required more often. Maintenance I — Use Maintenance I if the CHANGE ENGINE OIL SOON message comes on within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II — Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the message comes on 10 months or more since the last service or if the message has not come on at all for one year.


6-4


Scheduled Maintenance


Service


Maintenance I Maintenance II


Change engine oil and filter. See Engine Oil on page 5-15. Reset oil life system. See Engine Oil Life System on page 5-18. An Emission Control Service. Lubricate chassis components. See footnote #. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner filter or change indicator (if equipped). If necessary, replace filter. See Engine Air Cleaner/Filter on page 5-19. See footnote (l). Rotate tires and check inflation pressures and wear. See Tire Inspection and Rotation on page 5-75 and “Tire Wear Inspection” in At Least Once a Month on page 6-10. Inspect brake system. See footnote (a). Check engine coolant and windshield washer fluid levels and add fluid as needed. Perform any needed additional services. See “Additional Required Services” in this section. Inspect suspension and steering components. See footnote (b). Inspect engine cooling system. See footnote (c). Inspect wiper blades. See footnote (d). Inspect restraint system components. See footnote (e). Lubricate body components. See footnote (f). Check transmission fluid level and add fluid as needed.



• •







• •







• • • • • •


6-5


Additional Required Services The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item.


Service and Miles (Kilometers)


Additional Required Services 75,000


25,000
(40 000)

Loading...
x