1995 Chevrolet Tahoe Owners Manual

(Continued)

7-47

Maintenance Schedule I - Gasoline Engines Heavy Duty Emissions

(Continued)

Inspect accessory drive (serpentine) belt for cracks, fraying and wear and check belt for proper tension. Adjust or replace belt as needed. An Emission Control Service. Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. If your engine has a thermostatically controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

I DATE' I ACTUALMILEAGE I SERVICED BY:

50,000 Miles (83 000 km) 0 Change transmission fluid and filter if the vehicle is mainly driven

under one or more of these conditions:

a In heavy city traffic where the outside temperature regularly

reaches 90°F (32°C) or higher. a In hilly or mountainous terrain. a When doing frequent trailer towing.

(Continued)

7-48

Maintenance Schedule I - Gasoline Engines Heavy Duty Emissions

(Continued)

Uses such as found in taxi, police or delivery service.

If you do not use your vehicle under any of these conditions, the.fZuid andfilter do not require changing.

0 Manual transmission fluid doesn't require change.

Lubricate transmission shift linkage, parking brake cable guides and underbody contact points (or every 6 months, whichever occurs first). DATE I ACTUALMILEAGE I SERVICED BY:

51,000 Miles (85 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

17 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-1 2" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.*'k

DATE

ACTUAL MILEAGE

SERVICED BY:

7-49

Maintenance Schedule I - Gasoline Engines Heavy Duty Emissions

54,000 Miles (90 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C ) , or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

front axle propshaft splines,

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.** 0 Replace spark plugs. An Emission Control Service. 0 Rotate tires. See "Tire Inspection and Rotation" in the Index for proper

rotation pattern and additional information

57,000 Miles (95 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

(Continued)

7-50

Maintenance Schedule I - Gasoline Engines Heavy Duty Emissions

(Continued) 0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.""

DATE

ACTUAL MILEAGE

SERVICED BY:

60,000 Miles (100 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-1 2" C ) , or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking.** Inspect air cleaner filter if you are driving in dusty conditions. Replace filter if necessary. An Emission Control Service. Replace fuel filter. Replace filter sooner if it is clogged.? Inspect spark plug wires. An Emission Control Service. 7

(Continued)

7-5 1

Maintenance Schedule I - Gasoline Engines Heavy Duty Emissions

(Continued)

Inspect fuel tank, lines, rails, injection assembly, cap and cap gasket. An Emission Control Service. ?Fuel filter replacement is not required. Inspect accessory drive (serpentine) belt for cracks, fraying and wear and check belt for proper tension. Adjust or replace belt as needed. An Emission Control Service. Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. If your engine has a thermostatically controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

7-52

I Maintenance Schedule II - Gasoline Engines With

Heavy Duty Emissions

The services shown in this schedule up to 60,000 miles (100 000 km) should be performed after 60,000 miles ( 100 000 km) at the same intervals. Footnotes ** Drive axle service: 0 Locking Differential - Drain fluid and refill at first engine oil change.

At subsequent oil changes, check fluid and add fluid as needed. If driving in dusty areas or towing a trailer, drain fluid and refill every 15,000 miles (25 000 km).

0 Standard Differential - Check fluid level and add fluid as needed at every engine oil change. If driving in dusty areas or towing a trailer, drain fluid and refill every 15,000 miles (25 000 km).

0 More frequent lubrication may be required for heavy-duty or off-road

use.

6,000 Miles (10 000 km)

Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.*:*

0 Rotate tires. See “Tire Inspection and Rotation’’ in the Index for proper

rotation pattern and additional information.

DATE SERVICED

ACTUAL MILEAGE

BY:

I Maintenance Schedule II - Gasoline Engines With

Heavy Duty Emissions

12,000 Miles (20 000 km)

Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service. 0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.**

DATE

ACTUAL MILEAGE

SERVICED BY:

18,000 Miles (30 000 km) 0 Change engine oil and filter (or every 12 months, whichever occurs

first). An Emission Control Service.

1 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking."'"

(Continued)

7-54

Maintenance Schedule II - Gasoline Engines With Heavy Duty Emissions

1 Lvntinued) 0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information.

I DATE

I ACTUALMILEAGE I SERVICED BY:

24,000 Miles (40 000 km)

Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.**

0 Inspect engine accessory drive belts (or every 24 months, whichever

occurs first). An Emission Control Service.

0 Drain, flush and refill cooling system (or every 24 months, whichever

occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Service. Replace air cleaner filter. An Emission Control Service.

0 Replace fuel filter. An Emission Control Service.

DATE

I ACTUALMILEAGE I SERVICED BY:

7-55

Maintenance Schedule II - Gasoline Engines With Heavy Duty Emissions

27,000 Miles (45 000 km) 0 Replace spark plugs. An Emission Control Service.

DATE

ACTUAL MILEAGE

SERVICED BY:

30,000 Miles (SO 000 km) 0 Change engine oil and filter (or every I2 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.*‘’:

0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information.

I DATE

I ACTUAL MILEAGE

SERVICED BY:

7-56

I Maintenance Schedule II - Gasoline Engines With

Heavy

Duty

36,000 Miles (60 000 km) 0 Change engine oil and filter (or every 12 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.*#:

I DATE

I ACTUALMILEAGE I

SERVICED BY:

42,000 Miles (70 000 km) 0 Change engine oil and filter (or every 12 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (- 12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.'$'$

(Continued)

Maintenance Schedule II .- Gasoline Engines With Heavy Duty Emissions

(Continued)

Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information.

I DATE

I ACTUALMILEAGE I SERVICED B Y

48,000 Miles (80 000 km)

Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is IO” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whi2hever occurs first). Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking.** Inspect engine accessory drive belts (or every 24 months, whichever occurs first). An Emission Control Service. Inspect camshaft timing belt. An Emission Control Service. Drain, flush and refill cooling system (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Service. Replace spark plugs. An Emission Control Service.

(Continued)

7-5 8

I Maintenance Schedule II - Gasoline Engines With

Heavy

Duty

(Continued) 0 Replace air cleaner filter. An Emission Control Service. 0 Replace fuel filter. An Emission Control Service.

DATE SERVICED

ACTUAL MILEAGE

BY:

50,000 Miles (83 000 km) 0 Change automatic transmission fluid and filter if the vehicle is mainly

driven under one or more of these conditions:

In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. In hilly or mountainous terrain. When doing frequent trailer towing. Uses such as found in taxi, police or delivery service.

If you do not use your vehicle under any of these conditions, the.fluid and.filter do not require chartging.

0 Manual transmission fluid doesn’t require change.

DATE

ACTUAL

MILEAGE

SERVICED

BY:

7-59

Maintenance Schedule II - Gasoline Engines With Heavy Duty Emissions

54,000 Miles (90 000 km)

Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking."" Replace spark plugs. An Emission Control Service. Rotate tires. See "Tire Inspection and Rotation" in the Index for proper rotation pattern and additional information.

DATE

ACTUAL MILEAGE

SERVICED BY:

60,000 Miles (100 000 km) 0 Change engine oil and filter (or every 12 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C ) , or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

(Continued)

7-60

I Maintenance Schedule II - Gasoline Engines With

Heavy Duty Emissions

(Continued) 17 Check readfront axle tluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.‘k* Inspect engine accessory drive belts (or every 24 months, whichever occurs first). An Etnission Control Service.

0 Inspect camshaft timing belt. An Emission Control Service. 0 Inspect spark plug wires. An Emksion Control Service. -1 0 Inspect fuel tank, lines, rails, injection assembly, cap and cap gasket.

An Emission Control Service.

I Maintenance Schedule I - Diesel Engines

The services shown in this schedule LLP to 60,000 miles (100 000 km) should be performed after 60,000 miles ( IO0 000 km) at the same intervals. Footnotes ‘:: When the vehicle is operated in extreme dust and dirt conditions (off-road), the air cleaner filter may need to be checked as often as every 300 miles (483 km) and replaced as necessary. ‘k’k Drive axle service:

0 Locking Differential - Drain fluid and refill at first engine oil change.

At subsequent oil changes, check fluid and add fluid as needed. If driving in dusty areas or towing a trailer, drain fluid and refill every 15,000 miles (25 000 km). Standard Differential - Check fluid level and adu rlulu as neeaea at every engine oil change. If driving in dusty areas or towing a trailer, drain fluid and refill every 15,000 miles (25 000 km). More frequent lubrication may be required for heavy-duty or off-road use.

7-6 1

I

I Maintenance Schedule 2,500 Miles (4 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

I - Diesel Engines

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

DATE

ACTUAL MILEAGE

SERVICED BY:

5,000 Miles (8 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. **

DATE

ACTUAL MILEAGE

SERVICED BY:

7-62

I Maintenance Schedule I - Diesel Engines

7,500 Miles (12 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-I 2” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

17 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. See “Tires” in the Index.

DATE

ACTUAL MILEAGE

SERVICED BY:

10,000 Miles (16 000 km) 17 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

(Continued)

7-63

--

I Maintenance Schedule

I - Diesel Engines

(Continued)

Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. If your engine has a thermostatically controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. l::i:

DATE SERVICED

ACTUAL MILEAGE

BY:

12,500 Miles (20 000 km) CI

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

I DATE

I ACTUALMILEAGE I SERVICED BY:

7-64

I Maintenance Schedule I - Diesel Engines 15,000 Miles (24 000 km) [7 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12' C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). conditions. An Emission Control Service. *

0 Replace air cleaner filter. Replace filter more often under dusty

0 For 2-Wheel Drive vehicles only: Clean and repack the front wheel

0 Check readfront axle fluid level and add fluid as needed. Check

bearings (or at each brake relining, whichever occurs first). constant velocity joints and axle seals for leaking. **

DATE

ACTUAL

MILEAGE

SERVICED

B Y

I Maintenance Schedule

I - Diesel Engines

17,500 Miles (28 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

20,000 Miles (32 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

(Continued)

7-66

I Maintenance Schedule I - Diesel Engines

(Continued)

Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. If your engine has a thermostatically controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. ** DATE

ACTUAL MILEAGE

SERVICED BY:

22,500 Miles (36 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. See “Tires” in the Index. DATE

ACTUAL MILEAGE

SERVICED BY

I I Maintenance Schedule I - Diesel Engines

~~

25,000 Miles (40 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. **

DATE

ACTUAL MILEAGE

SERVICED BY:

27,500 Miles (44 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

DATE SERVICED

ACTUAL MILEAGE

BY:

7-68

I Maintenance Schedule I - Diesel Engines

30,000 Miles (48 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). Drain, flush and refill the cooling system with new coolant (or every 24 months, whichever occurs first). See "Engine Coolant" in the Index for what to use. An Emission Control Service. Also inspect the hoses and replace them if they are cracked, swollen or deteriorated. Tighten all hose clamps (except constant tension clamps). Remove debris and clean the outside of the radiator and air conditioning condenser. Wash the radiator neck. To ensure proper operation, pressure test the radiator and cap.

0 Replace air cleaner filter. Replace filter more often under dusty

conditions. An Emission Control Service. 'k

0 For 2-Wheel Drive vehicles only: Clean and repack the front wheel

bearings (or at each brake relining, whichever occurs first).

0 Replace fuel filter. Replace filter sooner if it is clogged.? 0 Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

(Continued)

7-69

I Maintenance Schedule

I - Diesel Engines

(Continued) 0 Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 If your engine has a thermostatically controlled cooling fan, inspect all

hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. **

I DATE

I ACTUALMILEAGE I SERVICED B Y

32,500 Miles (52 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-1 2" C ) , or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

DATE SERVICED

ACTUAL MILEAGE

B Y

I

first). An Emission Control Service.

I - Diesel Engines

I Maintenance Schedule 35,000 Miles (56 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs c Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pia bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. ** DATE

ACTUAL MILEAGE

SERVICED BY:

37,500 Miles (60 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). Rotate tires. See "Tire Inspection and Rotation'' in the Index for proper rotation pattern and additional information. See "Tires" in the Index.

DATE

ACTUAL MILEAGE

SERVICED BY:

I

I Maintenance Schedule 40,000 Miles (64 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

I - Diesel Engines

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 If your engine has a thermostatically controlled cooling fan, inspect all

hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. *#'

DATE

ACTUAL

MILEAGE

SERVICED BY:

7-72

I Maintenance Schedule I - Diesel Engines

$2,500 Miles (68 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

I DATE I ACTUALMILEAGE I SERVICED BY:

45,000 Miles (72 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). conditions. An Emission Control Service. *

0 Replace air cleaner filter. Replace filter more often under dusty

0 For 2-Wheel Drive vehicles only: Clean and repack the front wheel

bearings (or at each brake relining, whichever occurs first).

(Continued)

7-73

I Maintenance Schedule

I - Diesel Engines

(Continued) 0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. **

47,500 Miles (76 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

DATE

ACTUAL MILEAGE

SERVICED BY:

7-74

Maintenance Schedule I - Diesel Engines

50,000 Miles (80 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-1 2" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

0 In heavy city traffic where the outside temperature regularly

reaches 90°F (32°C) or higher. In hilly or mountainous terrain.

0 When doing frequent trailer towing.

Uses such as found in taxi, police or delivery service. lfyou do not use your vehicle under any of these conditions, the fluid and filter do not require changing.

Manual transmission fluid doesn't require change. Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. If your engine has a thermostatically controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold United States.

in the

(Continued)

7-75

I I Maintenance Schedule I - Diesel Engines

(Continued) 0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. **

DATE SERVICED

ACTUAL MILEAGE

BY:

52,500 Miles (84 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. See “Tires” in the Index.

DATE ACTUAL MILEAGE SERVICED

BY:

7-76

I Maintenance Schedule I - Diesel Engines 55,000 Miles (88 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. **

ACTUAL MILEAGE

SERVICED BY:

57,500 Miles (92 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

DATE SERVICED BY: ACTUAL MILEAGE

7-77

Maintenance Schedule I - Diesel Engines

60,000 Miles (100 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first). Drain, flush and refill the cooling system with new coolant (or every 24 months, whichever occurs first). See "Engine Coolant'' in the Index for what to use. An Emission Control Service. Also inspect the hoses and replace them if they are cracked, swollen or deteriorated. Tighten all hose clamps (except constant tension clamps). Remove debris and clean the outside of the radiator and air conditioning condenser. Wash the radiator neck. To ensure proper operation, pressure test the radiator and cap. Replace air cleaner filter. Replace filter more often under dusty conditions. An Emission Control Service. * For 2-Wheel Drive vehicles only: Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first). Check the crankcase depression regulator valve system for any worn, plugged or collapsed hoses, See service manual. An Emission Control Service. Replace fuel filter. Replace filter sooner if it is clogged.? Check the EGR System (if equipped) (except Code F engine) as described in the service manual. An Emission Control Service.

(Continued)

7-78

I Maintenance Schedule I - Diesel Engines

I7 Inspect accessory drive (serpentine) belt for cracks, fraying and wear and check belt for proper tension. Adjust or replace belt as needed. An Emission Control Service.

0 Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

[J If your engine has a thermostatically controlled cooling fan, inspect all

hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check the exhaust pressure regulator valve for proper operation;

correct any binding. Inspect hoses for cracks, chafing or decay. Replace parts as needed. An Emission Control Service.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. **

7-79

The services shown in this schedule up to 60,000 miles (100 000 kin) should be performed after 60,000 miles ( 100 000 km) at the same intervals.

Footnotes *#: Drive axle service:

Locking Differential - Drain fluid and refill a t first engine oil change. At subsequent oil changes, check fluid level and add fluid as needed. If driving in dusty areas or towing a trailer, drain fluid and refill every 15,000 miles (25 000 km). Standard Differential - Check fluid level and add fluid as needed at every engine oil change. If driving in dusty areas or towing a trailer, drain fluid and refill every 15,000 miles (25 000 km). More frequent lubrication may be required for heavy-duty or off-road use.

5,000 Miles (8 000 km) 0 Change engine oil and filter (or every 12 months. whichever occurs

first). A12 Emission C o m - d Scr-\v’w.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage. parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occ~~rs

first).

0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. See “Tires” in the Index.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking.

.:, .!.

‘I-’’-

Maintenance Schedule

II - Diesel Engines

10,000 Miles (16 000 km) 0 Change engine oil and filter (or every 12 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. 0 Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fateners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 If your engine has a thermostatically controlled cooling fan, inspect all

hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. **

DATE

ACTUAL MILEAGE

SERVICED BY:

7-81

-.

I

1 Maintenance Schedule 15,000 Miles (24 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

II - Diesel Engines

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. See “Tires” in the Index.

0 Check readfront axle fluid level and add fluid ai needed. Check

constant velocity joints and axle seals for leaking. **

DATE

ACTUAL MILEAGE

SERVICED BY:

20,000 Milles (32 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C ) , or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

(Continued)

7-82

I Maintenance Schedule II - Diesel Engines

Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. If your engine has a thermostatically controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. **

I DATE I ACTUALMILEAGE I SERVICED BY:

25,000 Miles (40 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, linkage, parking brake

transmission shift linkage, transfer case shift cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

(Continued)

7-83

-q_

(Continued) 0 Rotate tires. See “Tire Inspection and Rotation’’ in the Index for proper

rotation pattern and additional information. See “Tires” in the Index.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. **

DATE SERVICED

ACTUAL MILEAGE

BY:

30,000 Miles (48 000 km) 17 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

17 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Drain, flush and refill the cooling system with new coolant (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. An Emission Control Service. Also inspect the hoses and replace them if they are cracked, swollen or deteriorated. Tighten all hose clamps (except constant tension clamps). Remove debris and clean the outside of the radiator and air conditioning condenser. Wash the radiator neck. To ensure proper operation, pressure test the radiator and cap.

(Continued)

7-84

0 For 2-Wheel Drive vehicles only: Clean and repack the front wheel

bearings (or at each brake relining, whichever occurs first).

0 Replace fuel filter. Replace filter sooner if it is clogged.?

Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 If your engine has a thermostatically controlled cooling fan, inspect all

hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. :I:;!:

I DATE

I ACTUALMILEAGE I SERVICED BY:

7-85

1 Maintenance Schedule

II - Diesel Engines

35,000 Miles (56 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Contr-ol Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-1 2” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every I2 months, whichever occurs first).

0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

rotation pattern and additional information. See “Tires” in the Index.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. *4’

I DATE

I ACTUALMILEAGE I SERVICED BY:

40,000 Miles (64 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

(Continued)

7-86

I Maintenance Schedule II - Diesel Engines

(Continued)

Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. If your engine has a thermostatically controlled cooling fan, inspect all hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. Check readfront axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. **

DATE

ACTUAL MILEAGE

SERVICED

BY:

45,000 Miles (72 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

(Continued)

7-87

(Colltinued) 0 Rotate tires. See “Tire Inspection and Rotation” i n the Index for proper

rotation pattern and additional information. See “Tires” in the Index.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. ‘g‘k

DATE

ACTUAL MILEAGE

SERVICED BY:

50,000 Miles (80 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Change automatic transmission fluid and filter if the vehicle is mainly

driven under one or more of these conditions:

In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. In hilly or mountainous terrain. When doing frequent trailer towing.

0 Uses such as found in taxi, police or delivery service. If you do

not use your vehicle under any of these conditions, the fluid and filter do not require changing. Manual transmission fluid doesn’t require change.

(Continued)

7-88

1 Maintenance Schedule

II - Diesel Engines

(Continued) 0 Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 If your engine has a thermostatically controlled cooling fan, inspect all

hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check readfront axle fluid level and add fluid as needed. Check

constant velocity joints and axle seals for leaking. **

DATE

ACTUAL MILEAGE

SERVICED BY:

55,000 Miles (88 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10" F (-12" C ) , or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

(Continued)

7-89

(Continued) 0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper

0 Check readfront axle fluid level and add fluid as needed. Check

rotation pattern and additional information. See “Tires” in the Index. constant velocity joints and axle seals for leaking. **

60,000 Miles (100 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs

first). An Emission Control Service.

0 Lubricate the front suspension, king pin bushings, steering linkage, transmission shift linkage, transfer case shift linkage, parking brake cable guides, rear driveline center splines, front axle propshaft splines, brake pedal springs and clutch pedal springs. Ball joints and king pin bushings should not be lubricated unless their temperature is 10” F (-12” C), or higher. When weather is cold, let the ball joints and king pin bushings warm up before lubrication or they could be damaged. Perform each of the listed lubrication service items at this mileage interval (or every 12 months, whichever occurs first).

0 Drain, flush and refill the cooling system with new coolant (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. An Emission Control Service. Also inspect the hoses and replace them if they are cracked, swollen or deteriorated. Tighten all hose clamps (except constant tension clamps). Remove debris and clean the outside of the radiator and air conditioning condenser. Wash the radiator neck. To ensure proper operation, pressure test the radiator and cap.

(Continued)

7-90

I Maintenance Schedule II - Diesel Engines

(Continued) 0 Replace air cleaner filter. An Emission Control Service. 0 For 2-Wheel Drive vehicles only: Clean and repack the front wheel

bearings (or at each brake relining, whichever occurs first).

0 Check the crankcase depression regulator valve system for any worn, plugged or collapsed hoses. See service manual. An Emission Control Service.

0 Replace fuel filter. Replace filter sooner if it is clogged.? 0 Check the EGR System (if equipped) (except Code F engine) as described in the service manual. An Emission Control Service.

0 Inspect accessory drive (serpentine) belt for cracks, fraying and wear and check belt for proper tension. Adjust or replace belt as needed. An Emission Control Service.

0 Inspect shields and underhood insulation for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. 0 Check the air intake system installation to assure that gaskets are properly sealed and that all hose connections, fasteners and other components are tight. Also check to be sure that the air cleaner housing is properly seated, the cover fits tightly and the wing nuts are tight. Tighten connections and fasteners or replace damaged parts as necessary. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 If your engine has a thermostatically controlled cooling fan, inspect all

hoses and ducts for proper hook-up (or every 12 months, whichever occurs first). Be sure the valve works properly. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States.

0 Check the exhaust pressure regulator valve for proper operation;

correct any binding. Inspect hoses for cracks, chafing or decay. Replace parts as needed. An Emission Control Service. constant velocity joints and axle seals for leaking. **

0 Check readfront axle fluid level and add fluid as needed. Check

Part B: Owner Checks and Services Listed below are owner checks and services which should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Part D. At Each Fuel Fill It is important for you or u service station attendant to perjorm these underhood checks at each

fuel fill.

Engine Oil Level Check the engine oil level and add the proper oil if necessary. See “Engine Oil” in the Index for further details.

Engine Coolant Level Check the engine coolant level and add the proper coolant mix if necessary. See “Coolant” in the Index for further details.

Windshield Washer Fluid Level Check the windshield washer fluid level in the windshield washer tank and add the proper fluid if necessary. See “Windshield Washer Fluid” in the Index for further details.

At Least Once a Month

lire Inflation Check tire inflation. Make sure tires are inflated to the pressures specified on the Certificationire label which is located on the rear edge of the driver’s door or on the incomplete vehicle document in the cab. See “Tires” in the Index for further details.

Cassette Deck Clean cassette deck. Cleaning should be done every 50 hours of tape play. See “Audio Systems” in the Index for further details.

At Least Once a Year

Key Lock Cylinders Lubricate the key lock cylinders with the lubricant specified in Part D.

Body Lubrication Lubricate all fuel door, body hood and body door hinges, rear compartment hinges, tailgate and tailgate handle pivot points, tailgate mounted spare tire carrier pivot points, latches, locks, and folding seat hardware. Part D tells you what to use. More frequent lubrication may be required when exposed to a corrosive environment.

Starter Switch

1. Before you start, be sure you have enough room around the vehicle. It

should be parked on a level surface.

2. Firmly apply both the parking brake (see “Parking Brake” in the Index

if necessary) and the regular brake. NOTE: Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.

3. On automatic transmission vehicles, try to start the engine in each gear.

The starter should work only in PARK (P) or NEUTRAL (N). If the starter works in any other position, your vehicle needs service. On manual transmission vehicles, put the shift lever in NEUTRAL (N), push the clutch down halfway and try to start the engine. The starter should work only when the clutch is pushed down all the way to the floor. If the starter works when the clutch isn’t pushed all the way down, your vehicle needs service.

7-93

Brake-Transmission Shift Interlock -= BTSI

1. Before you start, be sure you have enough room around the vehicle. It

should be parked on a level surface.

2. Firmly apply both the parking brake (see “Parking Brake” in the Index

if necessary). NOTE: Be ready to apply the regular brake immediately if the vehicle begins to move.

3. With the engine off, turn the key to the RUN position, but don’t start the

engine. Without applying the regular brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out of PARK (P), your vehicle’s BTSI needs service.

Steering Column Lock While parked, and with the parking brake set, try to turn the key to LOCK in each shift lever position.

With an automatic transmission, the key should turn to LOCK only when the shift lever is in PARK (P). With a manual transmission, the key should turn to LOCK only when the shift lever is in REVERSE (R).

On vehicles with a key release button, try to turn the key to LOCK without pressing the button. The key should turn to LOCK only with the key button depressed. On vehicles with a key release lever, try to turn the key to LOCK without pressing the lever. The key should turn to LOCK only with the key lever depressed. On all vehicles, the key should come out only in LOCK.

7-94

Parking Brake and Automatic Transmission PARK (P) Mechanism Check

Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. 0 To check the parking brake: With the engine running and transmission in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only.

0 To check the PARK (P) mechanism’s holding ability: Shift to PARK

(P). Then release all brakes.

Lap and Shoulder Belts Condition and Operation Inspect belt system, including: webbing, buckles, latch plates, retractors, guide loops and anchors. Have a belt assembly replaced if the webbing has been cut or otherwise damaged.

Part C: Periodic Maintenance Inspections Listed below are inspections and services which should be performed at least twice a year (for instance, each spring and fall). You should let your GM dealer’s service department or other qualified service center do these jobs. Make sure any necessary repairs are completed at once.

Steering and Suspension lnspection Inspect the front and rear suspension and steering system for damaged, loose or missing parts, signs of wear, or lack of lubrication. Inspect power steering lines and hoses for proper hookup, binding, leaks, cracks, chafing, etc. (On vehicles equipped with manual steering gear, check for seal leakage.)

Exhaust System lnspection Inspect the complete exhaust system. Inspect the body near the exhaust system. Look for broken, damaged, missing or out-of-position parts as well as open seams, holes, loose connections, or other conditions which could cause a heat build-up in the floor pan or could let exhaust fumes into the vehicle. See “Engine Exhaust’’ in the Index.

Accelerator Control System On gasoline engines, lubricate the pivot at the TBI throttle lever stud with engine oil. Do not oil any accelerator or cruise control cables. Replace any cables that have high effort or excessive wear.

Drive Axle Service Check readfront axle fluid level and add as needed. Check constant velocity joints and axle seals for leaking. Transfer Case (Four- Wheel Drive) Inspection Every 12 months or at oil change intervals, check front axle and transfer case and add lubricant when necessary. Oil the control lever pivot point and all exposed control linkage. Check vent hose at transfer case for kinks and proper installation. More frequent lubrication may be required on off-road use.

Part D: Recommended Fluids and Lubricants NOTE: Fluids and lubricants identified below by name, part number or specification may be obtained from your GM dealer. USAGE Engine Oil (Gasoline Engine)

Engine Oil (Diesel Engine)

FLUIDLUBRICANT Engine oil with the American Petroleum Institute Certified For Gasoline Engines “Starburst” symbol of the proper viscosity. To determine the preferred viscosity for your vehicle’s engine, see “Engine Oil” in the Index. Engine oil with the letters C F 4 S H is best for your vehicle. However, if CF-4/SH is not available, you may use CF-4/SG or CE/SH or CE/SG oil. These letters show American Petroleum Institute (API) levels of quality. They may be listed in reverse order, SHKF-4 or other letters such as, SH/CD, CE, CF-4. To determine the preferred viscosity for your vehicle’s diesel engine, see “Engine Oil” in the Index.

Engine Coolant

Coolant Supplement

Hydraulic Brake System

Hydraulic Clutch System

Parking Brake Cables

50/50 mixture of water and a good quality ethylene glycol base antifreeze or an approved recycled coolant conforming to GM Specification 6038-M. GM Part No. 3634621 or equivalent with a complete flush and refill. Delco Supreme 11 Brake Fluid (GM Part No. 1052535 or equivalent DOT-3 brake fluid). Hydraulic Clutch Fluid (GM Part No. 12345347 or equivalent). Chassis Lubricant (GM Part No. 1052497 or equivalent) or lubricant meeting requirements of NLGI Grade 2, Category LB or GC-LB.

USAGE Power Steering System

Manual Transmission (RPO MG5)

Automatic Transmission

.Key Lock Cylinders

Automatic Transmission Shift Linkage Floor Shift Linkage Chassis Lubrication

Front Wheel Bearings

Differential, Standard, Front and Rear Axle

Differential, Locking

Transfer Case

Column Shift Lever and Propeller Shaft

Windshield Washer Solvent

FLUIDLUBRICANT GM Power Steering Fluid (GM Part No. 10500 17 or equivalent). Synchromesh Transmission Fluid (GM Part No. 12345349 or equivalent). DEXRON@-111 Automatic Transmission Fluid. Lubricate with Multi-Purpose Lubricant (GM Part No. 12345 120) or synthetic SAE 5W-30 engine oil. Engine oil.

Engine oil. Chassis lubricant (GM Part No. I2346003 or equivalent) or lubricant meeting requirements of NLGI Grade 2, Category LB or GC-LB. Wheel bearing lubricant meeting requirements of NLGI Grade 2, Category GC or GC-LB (GM Part No. I2346003 or equivalent). Axle Lubricant (GM Part No. 105227 1) or SAE 8OW-90 GL-5 Gear Lubricant. Axle Lubricant (GM Part No. 1052271) or SAE 8OW-90 GL-5 Gear Lubricant. DEXRON@-111 Automatic Transmission Fluid. Chassis lubricant meeting requirements of NLGI Grade 2, Category LB or GC-LB (GM Part No. 12346003). GM Optikleen@ Washer Solvent (GM Part No. 1051515) or equivalent.

7-98

USAGE Propeller Shaft SplineKJniversal Joint

Hood Latch Assembly a. Pivots and Spring Anchor b. Release Pawl

Hood and Door Hinges

Weatherstrip Conditioning

Weatherstrip Squeaks

Gas Line

FLUIDLUBRICANT Chassis lubricant (GM Part No. 12346003 or equivalent) or lubricant meeting requirements of NLGI Grade 2, Category LB or GC-LB.

a. Engine oil. b. Chassis lubricant (GM Part No. 12346003 or equivalent) or lubricant meeting requirements of NLGI Grade 2, Category LB or GC-LB. Engine oil or Lubriplate Lubricant (GM Part No. 1050109). Engine Oil.

No. 12345 120 or equivalent). Dielectric Silicone Grease (GM Part No. 12345579 or equivalent). Spray-A-Squeek (GM Part No. 105 2277). Gas Line De-Icer (GM Part No. 1051516).

Body Door Hinge Pins, Tailgate Hinge and Linkage, Folding Seat, Fuel Door Hinge Outer Tailgate Handle Pivot Points Multi-Purpose Lubricant (GM Part

7-99

Part E: Maintenance Record