2011 Chevrolet Suburban Owners Manual

The instrument panel fuse block access door is located on the driver side edge of the instrument panel. Pull off the cover to access the fuse block.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (44,1)

10-44

Vehicle Care

Fuses

Usage

10

11

12

13
14

15

16

17

Instrument Panel Back Lighting Passenger Side Turn Signal, Stoplamp Passenger Door Module, Driver Unlock Power Door Lock 2
(Unlock Feature) Power Door Lock 2
(Lock Feature) Stoplamps, Center High‐ Mounted Stoplamp Rear Climate Controls Power Mirror Body Control Module (BCM) Accessory Power Outlets Interior Lamps

The vehicle may not be equipped with all of the fuses, relays, and features shown.

Fuses

Usage

Rear Seats Rear Accessory Power Outlet

Fuses

Usage Steering Wheel Controls Backlight Driver Door Module Dome Lamps, Driver Side Turn Signal Driver Side Turn Signal, Stoplamp

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (45,1)

Fuses

Usage

18

19

20

21

22

23
24

25

26

Power Door Lock 1
(Unlock Feature) Rear Seat Entertainment Ultrasonic Rear Parking Assist, Power Liftgate Power Door Lock 1
(Lock Feature) Driver Information Center (DIC) Rear Wiper Cooled Seats Driver Seat Module, Remote Keyless Entry System Driver Power Door Lock (Unlock Feature)

Circuit Breaker

LT DR

Usage

Driver Side Power Window Circuit Breaker

Harness Connector

LT DR

BODY BODY

Usage

Driver Door Harness Connection Harness Connector Harness Connector

Center Instrument Panel Fuse Block The center instrument panel fuse block is located underneath the instrument panel, to the left of the steering column.

Vehicle Care

10-45

Top View

Harness Connector

BODY 2

BODY 1

BODY 3

HEADLINER

Usage Body Harness Connector 2
Body Harness Connector 1
Body Harness Connector 3
Headliner Harness Connector 3

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (46,1)

10-46

Vehicle Care

Harness Connector HEADLINER

HEADLINER

SEO/

UPFITTER

Usage

Headliner Harness Connector 2
Headliner Harness Connector 1
Special Equipment Option Upfitter Harness Connector

Circuit Breaker

CB1

CB2

CB3

CB4

Usage

Passenger Side Power Window Circuit Breaker Passenger Seat Circuit Breaker Driver Seat Circuit Breaker Rear Sliding Window

Wheels and Tires

Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer.

{ WARNING . Poorly maintained and

improperly used tires are dangerous.

. Overloading the tires can

cause overheating as a result of too much flexing. There could be a blowout and a serious crash. See Vehicle Load Limits on page 9‑22.

(Continued)

WARNING (Continued)

. Underinflated tires pose the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when the tires are cold.

. Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when hitting a pothole. Keep tires at the recommended pressure.

. Worn or old tires can cause a

crash. If the tread is badly worn, replace them.

. Replace any tires that have been damaged by impacts with potholes, curbs, etc.

(Continued)

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (47,1)

Vehicle Care

10-47

WARNING (Continued)

. Improperly repaired tires can

cause a crash. Only the dealer or an authorized tire service center should repair, replace, dismount, and mount the tires.

. Do not spin the tires in

excess of 55 km/h (35 mph) on slippery surfaces such as snow, mud, ice, etc. Excessive spinning may cause the tires to explode.

20‐Inch Tires If your vehicle has the optional 20‐inch P275/55R20 size tires, they are classified as touring tires and are designed for on road use. The low‐profile, wide tread design is not recommended for off‐road driving. See Off-Road Driving on page 9‑6, for additional information.

Notice: If the vehicle has low‐profile tires, they are more susceptible to damage from road hazards or curb impact than standard profile tires. Tire and/or wheel assembly damage can occur when coming into contact with road hazards like, potholes, or sharp edged objects, or when sliding into a curb. The vehicle warranty does not cover this type of damage. Keep tires set to the correct inflation pressure and, when possible avoid contact with curbs, potholes, and other road hazards.

Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The following illustrations are examples of a typical P‐Metric and a LT‐Metric tire sidewall.

Passenger (P‐Metric) Tire (A) Tire Size: The tire size code is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (48,1)

10-48

Vehicle Care

criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. (C) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. (D) Tire Identification Number (TIN): The letters and numbers following DOT code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.

(E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information, see Uniform Tire Quality Grading on page 10‑63. (G) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommended tire pressure see Tire Pressure on page 10‑53 and Vehicle Load Limits on page 9‑22.

Light Truck (LT-Metric) Tire

(A) Tire Size: The tire size code is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (49,1)

criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. (C) Dual Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used in a dual configuration. For information on recommended tire pressure see Tire Pressure on page 10‑53
and Vehicle Load Limits on page 9‑22. (D) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards.

(E) Tire Identification Number (TIN): The letters and numbers following DOT code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (F) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (G) Single Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used as a single. For information on recommended tire pressure see Tire Pressure on page 10‑53 and Vehicle Load Limits on page 9‑22.

Vehicle Care

10-49

Tire Designations

Tire Size The following examples show the different parts of a tire size.

Passenger (P‐Metric) Tire

(A) Passenger (P‐Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width: The three‐digit number indicates the tire section width in millimeters from sidewall to sidewall.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (50,1)

10-50

Vehicle Care

(C) Aspect Ratio: A two‐digit number that indicates the tire height‐to‐width measurements. For example, if the tire size aspect ratio is 75, as shown in item C of the tire illustration, it would mean that the tire's sidewall is 75 percent as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted‐bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches. (F) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire

is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.

Light Truck (LT‐Metric) Tire

(A) Light Truck (LT‐Metric) Tire: The United States version of a metric tire sizing system. The letters LT as the first two characters in the tire size means a light truck tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width: The three‐digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio: A two‐digit number that indicates the tire height‐to‐width measurements.

For example, if the tire size aspect ratio is 75, as shown in item C of the light truck (LT‐Metric) tire illustration, it would mean that the tire's sidewall is 75 percent as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted‐bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches. (F) Load Range : Load Range. (G) Service Description: The service description indicates the load index and speed rating of a tire. If two numbers are given as in the example, 120/116, then

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (51,1)

this represents the load index for single versus dual wheel usage (single/dual). The speed rating is the maximum speed a tire is certified to carry a load.

Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight: The combined weight of optional accessories. Some examples of optional accessories are automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width.

Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in kPa (kilopascal) or psi (pounds per square inch) before a tire has built up heat from driving. See Tire Pressure on page 10‑53. Curb Weight: The weight of a motor vehicle with standard and optional equipment including the

Vehicle Care

10-51

maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR: Gross Vehicle Weight Rating. See Vehicle Load Limits on page 9‑22. GAWR FRT: Gross Axle Weight Rating for the front axle. See Vehicle Load Limits on page 9‑22.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (52,1)

10-52

Vehicle Care

GAWR RR: Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits on page 9‑22. Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT‐Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279
that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall.

Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lbs). See Vehicle Load Limits on page 9‑22. Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or

model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure on page 10‑53
andVehicle Load Limits on page 9‑22. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (53,1)

Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1.6 mm (1/16 in) of tread remains. See When It Is Time for New Tires on page 10‑60. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a

tire's traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 10‑63. Vehicle Capacity Weight: The number of designated seating positions multiplied by 68 kg (150 lbs) plus the rated cargo load. See Vehicle Load Limits on page 9‑22. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle capacity weight and the original equipment tire size and

Vehicle Care

10-53

recommended inflation pressure. See “Tire and Loading Information Label” under Vehicle Load Limits on page 9‑22.

Tire Pressure If the vehicle is a hybrid, see the hybrid supplement for more information. Tires need the correct amount of air pressure to operate effectively. Notice: Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:

. Tire overloading and

over-heating which could lead to a blowout.

. Premature or

irregular wear.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (54,1)

10-54

Vehicle Care

. Poor handling. . Reduced fuel economy.

Overinflated tires, or tires that have too much air, can result in:

. Unusual wear. . Poor handling. . Rough ride. . Needless damage from

road hazards.

A vehicle specific Tire and Loading Information label is attached to your vehicle. This label shows your vehicle's original equipment tires and the correct inflation pressures for your tires when they are cold. The recommended cold tire inflation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle's maximum load carrying capacity.

For additional information regarding how much weight your vehicle can carry, and an example of the Tire and Loading Information label, see Vehicle Load Limits on page 9‑22. How you load your vehicle affects vehicle handling and ride comfort. Never load your vehicle with more weight than it was designed to carry.

When to Check Check your tires once a month or more. Do not forget to check the pressure of the spare tire. See Full-Size Spare Tire on page 10‑82 for additional information.

How to Check Use a good quality pocket-type gauge to check tire pressure. You cannot tell if your tires are properly inflated simply by

looking at them. Radial tires may look properly inflated even when they are underinflated. Check the tire's inflation pressure when the tires are cold. Cold means your vehicle has been sitting for at least three hours or driven no more than 1.6 km (1 mile). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the pressure is low, add air until you reach the recommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gauge.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (55,1)

Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.

Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)

As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under‐ inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under‐inflated tire causes the tire to overheat and can lead to tire failure. Under‐inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under‐inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

Vehicle Care

10-55

Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start‐ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (56,1)

10-56

Vehicle Care

Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation on page 10‑56 for additional information. Federal Communications Commission (FCC) and Industry Canada See Radio Frequency Statement on page 13‑18 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310.

Tire Pressure Monitor Operation If the vehicle is a hybrid, see the hybrid supplement for more information.

This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmit the tire pressure readings to a receiver located in the vehicle.

When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure

shown on the tire loading information label. See Vehicle Load Limits on page 9‑22. A message to check the pressure in a specific tire displays in the Driver Information Center (DIC). The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed. For additional information and details about the DIC operation and displays see Driver Information Center (DIC) on page 5‑27 and Tire Messages on page 5‑44. The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and needs to be inflated to the proper pressure.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (57,1)

A Tire and Loading Information label shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load Limits on page 9‑22, for an example of the Tire and Loading Information label and its location. Also see Tire Pressure on page 10‑53. The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection on page 10‑59, Tire Rotation on page 10‑59 and Tires on page 10‑46. Notice: Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use only the GM-approved tire sealant available through your dealer or included in the vehicle.

TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message also displays. The malfunction light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause these to come on are: . One of the road tires has been

replaced with the spare tire. The spare tire does not have a TPMS sensor. The malfunction light and DIC message should go off after the road tire is replaced and the sensor matching process is performed successfully. See "TPMS Sensor Matching Process" later in this section.

Vehicle Care

10-57

The TPMS sensor matching process was not done or not completed successfully after rotating the tires. The malfunction light and the DIC message should go off after successfully completing the sensor matching process. See "TPMS Sensor Matching Process" later in this section. . One or more TPMS sensors

are missing or damaged. The malfunction light and the DIC message should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer for service.

. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended could prevent the TPMS from functioning properly. See Buying New Tires on page 10‑61.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (58,1)

10-58

Vehicle Care

. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.

If the TPMS is not functioning properly, it cannot detect or signal a low tire condition. See your dealer for service if the TPMS malfunction light and DIC message comes on and stays on. TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the vehicle’s tires or replacing one or more of the TPMS sensors. The TPMS sensor matching process should also be performed after replacing a spare tire with a road tire containing the TPMS sensor. The malfunction light and the DIC message should go off at the next ignition cycle. The sensors are matched to the tire/wheel positions,

using a TPMS relearn tool, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear. See your dealer for service or to purchase a relearn tool. There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. The TPMS sensor matching process is outlined below: 1. Set the parking brake. 2. Turn the ignition to ON/RUN with

the engine off.

3. Press Q and K on the Remote Keyless Entry (RKE) transmitter at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.

4. Start with the driver side

front tire.

5. Place the relearn tool against

the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.

6. Proceed to the passenger side

front tire, and repeat the procedure in Step 5.

7. Proceed to the passenger side

rear tire, and repeat the procedure in Step 5.

8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (59,1)

9. Turn the ignition to LOCK/OFF. 10. Set all four tires to the

recommended air pressure level as indicated on the Tire and Loading Information label.

Tire Inspection GM recommends that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month. Replace the tire if: . The indicators at three or

more places around the tire can be seen.

. There is cord or fabric

showing through the tire's rubber.

. The tread or sidewall is

cracked, cut, or snagged deep enough to show cord or fabric.

. The tire has a bump, bulge,

or split.

. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.

Tire Rotation Tires should be rotated every 12 000 km (7,500 miles). See Scheduled Maintenance on page 11‑3. The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle. This will ensure that the vehicle continues to perform most like it did when the tires were new. Any time you notice unusual wear, rotate the tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels.

Vehicle Care

10-59

See When It Is Time for New Tires on page 10‑60 and Wheel Replacement on page 10‑65.

When rotating the vehicle's tires, always use the correct rotation pattern shown here. Do not include the spare tire in the tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (60,1)

10-60

Vehicle Care

label. See Tire Pressure on page 10‑53 and Vehicle Load Limits on page 9‑22. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10‑56. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 12‑2.

{ WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, use a cloth or a

(Continued)

WARNING (Continued)

paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See If a Tire Goes Flat on page 10‑66.

Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.

When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires.

One way to tell when it is time for new tires is to check the treadwear indicators, which appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. Some commercial truck tires may not have treadwear indicators. See Tire Inspection on page 10‑59 and Tire Rotation on page 10‑59 for additional information. The rubber in tires ages over time. This is also true for the spare tire, if the vehicle has one, even if it is not being used. Multiple conditions

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (61,1)

affect how fast this aging takes place, including temperatures, loading conditions, and inflation pressure maintenance. Tires will typically need to be replaced due to wear before they may need to be replaced due to age. Consult the tire manufacturer for more information on when tires should be replaced. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. This area should be free of grease, gasoline or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.

Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed on the vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating. This way, the vehicle will continue to have tires that are designed to give the same performance and vehicle safety, during normal use, as the original tires. GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size.

Vehicle Care

10-61

If the tires have an all‐season tread design, the TPC spec number will be followed by an MS for mud and snow. See Tire Sidewall Labeling on page 10‑47 for additional information. GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep the vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of the vehicle. See Tire Inspection on page 10‑59 and Tire Rotation on page 10‑59 for information on proper tire rotation.

{ WARNING Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death. Only your dealer or authorized tire service center should mount or dismount the tires.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (62,1)

10-62

Vehicle Care

{ WARNING

{ WARNING

Mixing tires could cause you to lose control while driving. If you mix tires of different sizes, brands, or types (radial and bias-belted tires), the vehicle might not handle properly, and you could have a crash. Using tires of different sizes, brands, or types could also cause damage to the vehicle. Be sure to use the same size, brand, and type of tires on all wheels. This vehicle may have a different size spare than the road tires (those originally installed on the vehicle). When new, the vehicle included a spare tire and wheel assembly with a similar overall diameter as the vehicle's road tires and wheels, so it is all right to drive on it. Because this spare was developed for use on the vehicle, it will not affect vehicle handling.

Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving. A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.

If you must replace the vehicle's tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction type (radial and bias‐belted tires) as the vehicle's original tires. Vehicles that have a tire pressure monitoring system may give an inaccurate low‐pressure warning if non‐TPC Spec-rated tires are installed on the vehicle. Non‐TPC Spec-rated tires may give a low‐ pressure warning that is higher or lower than the proper warning level

you would get with TPC Spec-rated tires. See Tire Pressure Monitor System on page 10‑55. The vehicle's original equipment tires are listed on the Tire and Loading Information label. See Vehicle Load Limits on page 9‑22
for more information about the Tire and Loading Information label and its location on the vehicle.

Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, and electronic stability control, the performance of these systems can also be affected.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (63,1)

{ WARNING

If different sized wheels are used, there may not be an acceptable level of performance and safety if tires not recommended for those wheels are selected. This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems developed for the vehicle, and have them properly installed by a GM certified technician.

See Buying New Tires on page 10‑61 and Accessories and Modifications on page 10‑3 for additional information.

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:

Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires.

Vehicle Care

10-63

The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (64,1)

10-64

Vehicle Care

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when

tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (65,1)

Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.

{ WARNING

Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.

Vehicle Care

10-65

Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See If a Tire Goes Flat on page 10‑66 for more information. Used Replacement Wheels

{ WARNING

Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.

Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, check the alignment if there is unusual tire wear or if the vehicle is pulling to one side or the other. If the vehicle vibrates when driving on a smooth road, the tires and wheels might need to be rebalanced. See your dealer for proper diagnosis.

Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can be repaired. See your dealer if any of these conditions exist.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (66,1)

10-66

Vehicle Care

Tire Chains If your vehicle is a Hybrid, see the Hybrid Supplement for more information.

{ WARNING

If your vehicle has P265/65R18 or P275/55R20 size tires, do not use tire chains. They can damage your vehicle because there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash.

(Continued)

WARNING (Continued)

Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manufacturer's instructions. To help avoid damage to your vehicle, drive slowly, readjust or remove the device if it is contacting your vehicle, and do not spin your vehicle's wheels. If you do find traction devices that will fit, install them on the rear tires.

Notice: If your vehicle has P265/ 70R17 size tires, use tire chains only where legal and only when you must. Use chains that are the proper size for your vehicle's tires. Install them on the rear tires only.

Do not use chains on the front tires. Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer's instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.

If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle's tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (67,1)

the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop, well off the road, if possible.

Vehicle Care

10-67

{ WARNING

{ WARNING

Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

If your vehicle is a hybrid, see the hybrid supplement for more information.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (68,1)

10-68

Vehicle Care

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑5.

{ WARNING

Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving:

1. Set the parking brake firmly. 2. Put the shift lever in

P (Park).

(Continued)

WARNING (Continued)

3.

If you have a four-wheel-drive vehicle with a N (Neutral) transfer case position, be sure the transfer case is in a drive gear — not in N (Neutral). 4. Turn off the engine and do not restart while the vehicle is raised.

5. Do not allow passengers to

remain in the vehicle.

6. Put the wheel blocks at the

front and rear of the tire farthest away from the one being changed. That would be the tire on the other side, at the opposite end of the vehicle.

When the vehicle has a flat tire (B), use the following example as a guide to assist you in the placement of wheel blocks (A).

A. Wheel Block B. Flat Tire The following information explains how to use the jack and change a tire.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (69,1)

Vehicle Care

10-69

The tools you will be using include the following:

2. Remove the wing nut (B) used to

retain the tool bag by turning it counterclockwise.

3. Turn the knob (A) on the jack

counterclockwise to release the jack and wheel blocks from the bracket.

4. Remove the wheel blocks and

the wheel block retainer by turning the wing nut (C) counterclockwise.

Jack

A. B. Wheel Blocks C. Jack Handle D. Jack Handle Extensions E. Wheel Wrench

Tire Changing

Removing the Spare Tire and Tools The equipment you will need to change a flat tire is stored under the storage tray, which is located on the driver side trim panel (over the rear wheelhouse).

Regular Wheelbase Shown, Extended Wheelbase Similar 1. Remove the tray to access the tools by pulling up on the finger depression under the jack symbol.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (70,1)

10-70

Vehicle Care

To access the spare tire, refer to the following graphics and instructions:

A. Hoist Assembly B. Hoist Shaft C. Hoist Shaft Access Cover/Hole D. Jack Handle Extensions

E. Wheel Wrench F. Hoist Cable G. Tire/Wheel Retainer H. Spare Tire (Valve Stem

Pointed Down)

I. Hoist Shaft Access Hole J. Hoist End of Extension Tool K. Spare Tire Lock 1. Open the hoist shaft access

door (C) on the bumper to access the spare tire lock (K). 2. To remove the spare tire lock,

insert the ignition key, turn it clockwise and then pull it straight out.

3. Assemble the two jack handle

extensions (D) and wheel wrench (E) as shown.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (71,1)

Vehicle Care

10-71

If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower. See Secondary Latch System on page 10‑79 for more information.

4.

Insert the open end of the extension (J) through the hole in the rear bumper (I) (hoist shaft access hole). Be sure the hoist end (J) of the extension (D) connects to the hoist shaft (B). The ribbed square end of the extension is used to lower the spare tire.

5. Turn the wheel wrench (E)

counterclockwise to lower the spare tire (H) to the ground. Continue to turn the wheel wrench until the spare tire can be pulled out from under the vehicle.

7. Tilt the tire toward the vehicle

with some slack in the cable to access the tire/wheel retainer. Separate the retainer from the guide pin by sliding the retainer up the pin while pressing down on the latch.

6. Use the wheel wrench hook that allows you to pull the hoist cable towards you, to assist in reaching the spare tire.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (72,1)

10-72

Vehicle Care

Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before

proceeding. See If a Tire Goes Flat on page 10‑66 for more information.

If the wheel has a bolt-on hub cap, loosen the plastic nut caps by turning the wheel wrench counterclockwise. The plastic nut caps will be retained in the hub cap after it is removed from the wheel.

Once the retainer is separated from the guide pin, tilt the retainer and pull it through the center of the wheel along with the cable and latch.

8. Put the spare tire near the

flat tire.

2.

If your vehicle has a center cap that covers the wheel fasteners, place the chisel end of the wheel wrench in the slot on the wheel and gently pry the cap out.

3. Use the wheel wrench to loosen

all the wheel nuts. Turn the wheel wrench counterclockwise to loosen the wheel nuts. Do not remove the wheel nuts yet.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (73,1)

Vehicle Care

10-73

Front Tire Flat: If the flat tire is on a front tire of the vehicle, you will need to use the jack handle and only one jack handle extension. Attach the wheel wrench to the jack handle extension. Attach the jack handle to the jack (A). Position the jack on the frame behind the flat tire where the frame sections overlap. Turn the wheel wrench clockwise to raise the vehicle. Raise the vehicle far enough off the ground so there is enough room for the spare tire to clear the ground.

Jacking Locations (Overall View)

Front Position – 1500 Models

A. Front Position B. Rear Position

4. Position the jack under the

vehicle as shown.

Front Position – 2500 Models

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (74,1)

10-74

Vehicle Care

Rear Position – 1500 Models

{ WARNING

Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

Rear Tire Flat: If the flat tire is on a rear tire of the vehicle, you will need to use the jack handle (B) and both jack handle extensions (C). Attach the wheel wrench (D) to the jack handle extensions (C). Attach the jack handle (B) to the jack (A). Use the jacking pad provided on the rear axle. Turn the wheel wrench (D) clockwise to raise the vehicle. Raise the vehicle far enough off the ground so there is enough room for the spare tire to clear the ground.

{ WARNING

Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

Rear Position – All Other Models

5. Remove all of the wheel nuts. 6. Take off the flat tire.

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (75,1)

WARNING (Continued)

off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See If a Tire Goes Flat on page 10‑66.

8. Put the wheel nuts back on with

the rounded end of the nuts toward the wheel after mounting the spare tire.

Vehicle Care

10-75

{ WARNING

Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.

9. Tighten each wheel nut by hand.

Then use the wheel wrench to tighten the nuts until the wheel is held against the hub.

10. Turn the wheel wrench

counterclockwise to lower the vehicle. Lower the jack completely.

11. Tighten the nuts firmly in a

crisscross sequence as shown by turning the wheel wrench clockwise.

7. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel.

{ WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come (Continued)

Chevrolet Tahoe/Suburban Owner Manual - 2011

Black plate (76,1)

10-76

Vehicle Care

WARNING (Continued)

Specifications on page 12‑2 for original equipment wheel nut torque specifications.

Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 12‑2 for the wheel nut torque specification. When you reinstall the regular wheel and tire, you must also reinstall either the center cap or the bolt-on hub cap, depending on which your vehicle has.

For center caps, line up the tab on the center cap with the slot in the wheel. The cap only goes in one way. Place the cap on the wheel and press until it snaps into place.

For bolt-on hub caps, line up the plastic nut caps with the wheel nuts and tighten clockwise by