Download PDF Manual


Acc (Accessory): Acc wipers when toward you. Your steering wheel will remain locked, just inserted the key.


the engine is off. To get into Acc, push in the key and


the windshield turn it as it was before you


2-1 1


Features & Controls


to rem(


locks your ignition, steering wheel


LOCK: This position a theft deterrent feature. You will only be able ignition is turned to LOCK. Off: This position lets you turn off the engine but still Use Off if you must have your example, if your vehicle is being pushed). Run: This is the position for driving. Start: This starts your engine.


'a On manual transmission vehicles, turning the key to


vehicle in motion while


and transmission. it's the we your key when


turn the steering wheel. is off (for the engine


the steering column and result in a vehicle. This could cause a collision. off while the vehicle is moving, turn the key only to the key release lever while the vehicle


is moving.


loss of ability to steer the If you need


to turn the engine


OFF. Don't move


LOCK will lock


NOTICE


2-1 2


Key Release Lever


The ignition key cannot be removed from the ignition vehicles unless the key release lever is used.


of manual transmission


KO495


A On manual transmission vehicles,


while the vehicle is moving, the key only to column and result in


if you need to turn the engine


do not press the key release lever, turn


off


Off. Turning the key


to LOCK will lock the steering


loss of ability to steer the vehicle.


To Remove the Key On manual transmission vehicles, turn the key to the pressing the key release lever down. Keeping your finger on the lever, pull the key straight out. On automatic transmission vehicles, turn the key to out.


LOCK position while


LOCK and pull


it straight


2-1 3


Features & Controls


of your Vehicle Identification Number


You will find the VIN


of your instrument panel. (See “Vehicle Identification Number”


kmrting Your Engine Engines start differently. The 8th digit (VIN) shows the code letter or number for your engine. at the top left in the Index.) Follow the proper steps to start the engine. To Start Your 5.7 Liter (Code K) engine or 7.4 Liter (Code N) engine:


1. Automatic Transmission


Move your shift lever to in any other position-that’s already moving, use N (Neutral) only.


P (Park) or N (Neutral). Your engine won’t start


a safety feature. To restart when you’re


NOTICE Don’t try to shift to P (Park) if your vehicle is moving. could damaa stormed


our


If you do, is


p~&w$gp! you^^^^ P . icle


Manual Transmission Shift your gear selector to neutral and hold the clutch pedal to the while starting the engine, Your vehicle won’t start not all the way down-that’s


a safety feature.


if the clutch pedal is


floor


2. Don’t push the accelerator pedal before starting your engine.


other vehicles you might need to do this, but because computer systems, you don’t.


In some of your vehicle’s


3. Turn your ignition key to


Start. When the engine starts, let go


of the


key. The idle speed will go down as your engine gets warm. 7.4L Engine Cold Start: In cold weather, below 60°F (16°C)’ start the engine the same way but push the accelerator pedal one-quarter of the way down and hold it there for about


2 seconds after the engine starts.


Holding your key in Start for ‘longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive he damage your starter motor.


4. If it doesn’t start right away, hold your key in


Start. If it doesn’t start in


three seconds, push the accelerator pedal about one-quarter down for 12 more seconds,


or until it starts.


of the way


2-1 4


5. If your engine still won’t start


(or starts but then stops),


it could be


Try this:


flooded with too much gasoline. Wait 15 seconds to let the starter motor accelerator pedal all the way to the floor. Hold it there. Then, key in Start for no more than ten seconds. This clears the extra gasoline from the engine. 15 seconds and do Step 5 again.


If the engine still doesn’t start, wait another


cool down. Then push your


hold the


Hot Engine Restart, 5.7L and 7.4L Engines (Vehicles Over your engine is already hot and then stalls, turn your ignition key to turn your key engine. When the engine starts, let go of the key and accelerator pedal.


to Run, and wait about


20 seconds before you restart your


8500 GVWR): If Off. Then,


I NOTICE 1


rn


rn


four engine is designed to work with the electronics in your vehicle.


1 electrical parts or accessories, you could change tction system operates. Before adding electrical equipment, check with


the way the fuel


If you


dealer. If you don’t, your engine might not perform properly. h r I you ever have to have your vehicle towed, see the part of this :hat tells how to do it without damaging your vehicle. See “Towing Jehicle” in the Index.


Man,,l Your


Driving Through Deep Standing Water


f you drive too quickly through deep puddles or standing water, water can :me in through your engine’s air intake and badly damage your engine. If IOU can’t avoid deen ouddles or standino water, drive through very slowly.


2-1 5


Features & Controls


Engine BIock Heater (Option)


K221


In very cold weather, 0°F (-18°C) or colder, the engine block heater can help. You’ll get easier To use the block heater:


starting and better fuel economy during engine warm-up.


1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. 3. Plug it into a normal, grounded 110-volt outlet.


Plugging the cord into an ungrounded outlet muld cause an electrical L shock, Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded threeprong 110-volt outlet. If the cord won’t reach, use a heavy-duty threepmng extension cord rated for at least 15 amps.


I NOTICE


ter you’ve used the nanner it was, to help keep it away from moving engine parts. lon’t, it could be tom and damaged.


block heater, be sure to store the cord in the


If you


2-1 6


plugged in? The answer depends


the kind of oil you have, and


How long should you keep the block heater on the weather, trying to list everything here, we ask that you contact a General Motors dealer in the area where you’ll be parking your vehicle. The dealer can give you the best advice Automatic 7Pansmission


some other things. Instead of


for that particular area.


There are several different positions


for your gear lever.


P (Park)


This locks your rear wheels. enaine because your vehicle can’t move easily.


It’s the best position


to use when you start your


K2362


2-1 7


4 in P (Park) with the parking brake firmly set. It is dangerous to get out of your vehicle


if the shift lever


is not fully


Your vehicle can roll.


is running unless you have


Don’t leave your vehicle when the engine to, If you have left the engine running, the vehicle can move To be sure your vehicle suddenly. You or others could be injured. won’t move, wh’en you’re on fairly level ground, always set your parking brake and move the If you have four-wheel drive, your vehicle will your shift lever is in P (Park)-if your transfer case is in So, be sure the transfer case See “Shifting Into Park” if you’re pulling a trailer, also see “Parking on Trailer” in the Index.


is in a drive gear-not N (Neutral). in the Index. If you are parking on a hill, or Hills’’ or ‘Towing a


shift lever to P (Park).


be free to roll-even if N (Neutral).


R (Reverse) Use this gear to back up. I NOTICE


I! Shifting to R (Reverse) while your vehicle is moving forward could damage


jour transmission. Shift to R (Reverse) only after your vehicle


is stopped.


To rock your vehicle back and forth damaging your transmission, see “If You’re Stuck: Snow” in the Index. N (Neutral)


to get out of snow, ice or sand without Ice or


In Sand, Mud,


In this setting, your engine doesn’t connect with the wheels. you’re already moving, use N (Neutral) only. Also, use N when your vehicle being towed.


To restart when


I CAUTION


is


Shifting out of P (Park) or N (Neutral) while your engine is “racing” foot is firmly on (run’ning at high speed) is dangerous. Unless your the brake pedal, your vehicle could move very rapidly. control and hit people or objects. Don’t shift out of P (Park) or N (Neutral) while your engine is racing.


You could lose


2-1 8


NOTICE Damage to your transmission caused by shifting out of P (Park) or N {Neutral) with the engine racing isn’t covered


by your warranty.


OD (Automatic Overdrive)


This position vou’re:


is for normal driving.


If you need more power for passing, and


- Going less than about 35 mph (56 km/h), push your accelerator


pedal about halfway down


- Going about 35 mph (56 km/h) or more, push the accelerator


way down


all the


You’ll shift down to the next gear and have more power. OD should not be used when towing a trailer, carrying a heavy load, driving on steep hills, or for off-road driving. Select vehicle under any of these conditions.


D (third gear) when operating the


D (Third Gear)


This is like OD, but you never go into Overdrive. towing a trailer, carrying a heavy load, driving driving.


2 (Second Gear)


You should use D when


on steep hills, or for off-road


This position gives you more power but lower fuel economy. on hills. It can help control roads, but then you would also want If you manually select 2, the transmission will drive in second gear. You may use this feature for reducing torque start your vehicle from a stop on slippery road surfaces.


your speed as you go down steep mountain to use your brakes off and on.


to the rear wheels when you are trying to


You can use 2


1 (First Gear)


This position gives you even more power You can use lever is put in 1, the transmission won’t shift into first gear until the vehicle going ‘slowly enough.


(but lower fuel economy) than 2. If the selector


it on very steep hills, or


in deep snow or mud.


is


2-1 9


1


. . -.


I lf your rear wheels can’t rotate, don’t try to drive, This might happen if p u were stuck in very deep sand or mud or were up against a solid -‘-’ect. You could damage transmission. your


so, if you stop when going uphill, :he accelerator pedal. This could overheat and damage the transmission. Jse your brakes or shift to P (?k) ?ill. FivemSpeed Manual 7Pansmission


wi onl, don’t hold your vehicle there to hold your vehicle in position on a


*?isgi% :,e%-=


2-20


This is your shift pattern. Here’s how


to operate your transmission:


- . ’ :- -.


.. r


K2386


1. Then, slowly let


20 mph (32 km/h). If


1, put the


1 (First Gear)-Press the clutch pedal and shift into up on the clutch pedal as you press the accelerator pedal. You can shift into 1 when you’re going less than you’ve come to a complete stop and it’s hard to shift into shift lever in Neutral and let up on the clutch. Press the clutch pedal back down. Then shift into 2 (Second Gear)-Press the clutch pedal as you let up on the accelerator pedal and shift into 2.Then, slowly let up on the clutch pedal as you press the accelerator pedal. 3, 4 and 5 (Third, Fourth and Fifth Gears)-Shift into same way you do for 2.Slowly let up on the clutch pedal as you press the accelerator pedal.


1.


3, 4 and 5 the


on the accelerator pedal and press the brake pedal. Just


To Stop -Let up before the vehicle stops, press the clutch pedal and the brake pedal, and shift to Neutral. N (Neutral)-Use R (Reverse)-To back up, press the clutch the clutch pedal slowly while pressing the accelerator pedal.


this position when you start or idle your engine. pedal and shift into


R. Let up on


2-21


Shift to R (Reverse) only after your vehicle is stopped. Shifting to R .- ?verse) while your vehicle is moving could damage your transmisslor


:I


Also. use Reverse. alona with the Darkina brake. for oarkina vour vehic.,


Shift Light


K2317


if weather,


if you quickly


SHIFT light. This light will


is normal for the light to go on and off


For the best fuel economy, accelerate


If you have a manual transmission, you have a show you when to shift to the next higher gear for best fuel economy. When this light comes on, you can shift to the next higher gear road and traffic conditions let you. slowly and shift when the light comes on. While you accelerate, it change the position of the accelerator. Ignore the downshift. Four-wheel Drive Vehicles Only: If your vehicle has four-wheel drive and is equipped with a manual transmission, disregard the shift light when the transfer case is in Locking Rear Axle If you have this feature, your rear axle can give you additional traction on snow, mud ice, sand or gravel. It works like a standard axle most of the time, but when one does, the locking feature will allow the wheel with traction to move the vehicle.


of the rear wheels has no traction and the other one


4 LOW.


SHIFT light when you


2-22


Parking Brake


K2221


To set the parking brake: Hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your warning light will come on. To release the parking brake: Hold the regular brake pedal down. Pull the lever marked


left foot.


If the ignition is on, the brake system


RELEASE.


in the Index. That part shows how


If you are on a hill: See “Parking on Hills’’ wheels. If you are towing a trailer and are parking on any hill: See “Towing a Trailer” in the Index. That part shows what the trailer from moving.


to turn your front


to do first to keep


2-23


Features & Controls


in the transmission. It may be difficult


is called “torque lock.” To prevent this, the parking


If is placed in P (Park) before of the vehicle may put too much force


Torque Lock The parking brake should be set first whenever leaving the driver’s seat. you are parked on a hill and the transmission the parking brake is set, the weight on the parking pawl lever out of P (Park). This P (Park). brake should be set BEFORE moving the selector lever to When preparing to move the vehicle, the selector lever should be moved out of P (Park) BEFORE releasing the parking brake. Set the parking brake first, then release the transmission from If “torque lock” does occur, you may have your vehicle uphill a little to take some of the pressure off the transmission while you pull the selector lever out of Shifting lnto P (Park) (Automatic Transmission Models Only)


P (Park), even on level surfaces.


to have another vehicle nudge


P (Park).


to pull the selector


if the shift lever is not Your vehicle can


could be injured. To be sure your vehicle won’t move,


to get out of your vehicle


It can be dangerous fully in P (Park) with the parking brake firmly set. roll. If you have left the engine running, the vehicle can move suddenly. You or others when you’re on fairly level ground, use the steps that follow. If you have four-wheel drive, and your transfer case your vehicle will be free (Park). So, be sure (Neutral). If you are parking on a hill, “Parking on Hills”


if your shift lever is in is in a drive gear-not


to roll-even the transfer case


Trailer” in the Index.


“Towing


or


or if you’re pulling a trailer, also see


in N


is in N (Neutral), I


2-24


Steering Column Shift Lever


1. Hold the brake pedal down with your right


brake.


foot and set the parking


2. Move the shift lever


into the P (Park) position like this:


Pull the lever toward you.


Move the lever up


as far as it will


go.


K2316


3. If you have four-wheel drive, be


gear-not


in N (Neutral).


sure the transfer case


is in a drive


4. Move the ignition key 5. Remove the key and take


vehicle with the ignition key


to LOCK.


it with you. in your hand, your vehicle is in


If you can walk away from your


P (Park).


2-25


Features & Controls


Leaving Your Vehicle With the Engine Running (Automatic Transmission Models Only)


be free to


A It can be dangerous


to leave your vehicle with the engine running.


in


not fully


it could


the transfer


You or others


De sure your


if the shift lever is


could be injured. Don’t


if your shift lever in a drive gear-not


is in N (Neutral), your vehicle will is in P (Park). So be sure in N (Neutral).


h Your vehicle could move suddenly P (Park) with the parking brake firmly set. If you have four-wheel drive with a manual transfer case shift lever and your transfer case roll, even case is And, if you leave the vehicle with the engine running, overheat and even catch fire. leave your vehicle with the engine running unless you have to. If you have to leave your vehicle with the englne runnmg, vehicle is in P (Park) and your parking brake it. If you have four-wheel drive with a manual transfer case shift lever, in N (Neutral). that the transfer case After you’ve moved the shift lever into the brake pedal down. Then, P (Park) without first pulling If you can, it means that the shift lever wasn’t fully locked into P (Park). Parking Your Vehicle (Manual Transmission Models Only) Before you get out of your vehicle, put your manual transmission R (Reverse) and firmly apply the parking If you have four-wheel drive, be sure your transfer case Your vehicle could roll if it isn’t. If you are parking on see “Towing a


P (Park) position, hold see if you can move the shift lever away from


if your vehicle is equipped in the Index.


Trailer” or “Parking on Hills”


is in a drive gear-not


to tow a trailer,


it toward you.


a hill, or


brake.


in


is firmly set, before you leave


is in a drive gear.


be sure


the regular


2-26


Parking Over Things That Burn


. . .'.- L.' .


* Things that can burn could touch hot exhaust parts under


4 vehicle and ignite. Don't park over papers, leaves, dry grass


your


or other


that


things


AM220009


2-27


Features & Controls


Engine Exhaust


I I


It contains the gas carbon monoxide


Engine exhaust can kill. which you can’t see or smell. It can cause unconsciousness and death . You might have exhaust coming 0 Your exhaust system sounds


in if: strange or different.


(CO),


Your vehicle gets rusty underneath.


* Your vehicle was damaged


in a collision.


Your vehicle was damaged when driving road or over road debris.


over high points on the


m Repairs weren’t done correctly. e Your vehicle or exhaust system had been modified improperly. If you ever suspect exhaust 0 Drive it only with all the windows down to blow out any CO;


is coming into your vehicle:


and


* Have it fixed immediately.


2-28


Running Your Engine While You’re Parked (Automatic rnansrnission) It’s better not to park with the engine running. But if you ever have are some things to know. I CAUTION I A Idling the engine with the air system control A dangerous exhaust into your vehicle.


off could allow


(See the earlier Caution under


to, here


let deadly carbon monoxide (CO)


“Engine Exhaust”.) Also, idling in a closed-in place can into your vehicle even place this can happen is a garage. Exhaust-with easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard, {See “Blizzard” in Index.)


if the fan switch


is at the highest setting.


One


C h a n come in


the


if the shift lever is not


set. Your vehicle can roll.


It can be dangerous to get out of your vehicle fully in P with the parking brake firmly Don’t leave your vehicle when the engine is running unless you have to. If you’ve left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, always set your parking brake and move the shift lever to P (Park). If you have four-wheel drive, and you’re transfer case is in N (Neutral), your vehicle will be free to roll, even if your shift lever is in P (Park). So, be’ sure the transfer case is in a drive gear-not in N (Neutral). Follow the proper steps to be “Shifting Into Park” in the tndex. If you are parking on a hill, or if you’re pulling a trailer, also see “Parking on Hills” or “Trailer Towing” in the Index.


sure -your vehicle won? move. See


2-29


It can be dangerous


\ fully in P (Park) with the parking brake firmly set.


to get out of your vehicle if the shift lever If you have in a drive gear.


is nut


If you have left the engine running, the vehicle


four-wheel drive, also be sure the transfer case is Your vehicle can roll. can move suddenly. You vehicle won’t move, follow hill, or if you’re pulling a trailer, see “Parking Towing” in the Index.


or others could be injured. the steps below. If you


To be sure your are parking on a on Hills’’ or “Trailer


If your vehicle has four-wheel drive, you can send your engine’s driving power to all four wheels for extra traction. To get the most satisfaction out of four-wheel drive, you must be familiar with its operation. Read follows before using four-wheel drive. You should use 2H for most normal driving conditions.


the pan that


Driving in the 4H or 4L positions for a long time on dry or wet pavement could shorten the life of your vehicle’s drivetrain.


Transfer Case


2-30


The transfer case shift lever is on the floor lever to shift into and out of four-wheel drive. An indicator near t9e lever shows you


the transfer case settings:


to the right of the driver. Use this


4L


O N 2H 4H


is go


up, or


the indicator does not light


if the front axle light does not


of the indicator diagram will light up when you shift into


out of four-wheel drive, have your dealer check your


The front axle portion four-wheel drive. A slight delay between shifting and the indicator’s lighting normal. If out after you shift system. When your headlights or parking lights are on, rotate the dial to the right of your headlight switch light. Rotate the dial Transfer Case Shift Positions 2H (High): This setting Your front axle is not engaged 4H (High): This setting engages your front axle Use 4H when you need extra traction, such most off -road situations.


to adjust the brightness of your transfer case indicator up to brighten, or down


is for driving in most street and highway situations.


to dim, the indicator light.


as on wet or icy roads, or in


to help drive your vehicle.


in two-wheel drive.


2-31


Features & Contmls


to be towed or


off.


N (Neutral): Shift to this setting only when your vehicle needs when using a power take 4L (Low): This setting also engages your front but should be used only for off-road You can shift from 2H to 4H or from 4H to 2H while the vehicle Your front axle will engage faster if you take your foot for a few seconds after you shift. necessary to stop or slow the vehicle To shift into or out of 4L or N (Neutral):


to shift out of 2H.


or on extremely slippery surfaces.


In extremely cold weather it may be


is moving. off of the accelerator


axle to give you extra traction,


1. Slow the vehicle


to a roll, about 3 mph (5 km/h) and shift your


transmission into neutral.


2. Shift the transfer case shift lever


in one continuous motion.


4L, or your


in N (Neutral) as you shift the transfer case into


Don’t pause gears could clash. Remember that driving in 4H or 4L may reduce four-wheel drive on dry pavement could cause your tires to wear faster and make your transfer case harder Front Axle Locking Feature The front axle locks and unlocks automatically when you shift the transfer case. A slight delay for the axle temperature is very hot, or conditions, there may be a slight delay for the


the vehicle has been used


to lock or unlock


axle to unlock.


to shift.


is normal. If the outside under hard driving


fuel economy. Also, driving in


2-32


turn the hand crank on each door


To open your manual windows, lower your side door windows. If you have the optional power windows, the controls are on each doors . The driver's door has a switch for the passenger windows power windows will work when the ignition has been turned Push the rear of the switch with the power window symbol on window. Push the front of the switch with the power window symbol on window.


K2364


to raise or


of the side


as well. Your to ACC or Run.


it to lower the


it to raise the


2-33


Electric Tailgate Glass Release


PO271


Doors" in this section.


Before operating your electric tailgate glass release, see the caution under "Tailgate, Tailgate Glass and Rear The electric hatch release button, located below the headlight switch, lets you release the tailgate glass. hear the latch release the window. If you have an automatic transmission, your shift lever must be N (Neutral) for the release apply the parking brake for the release


To use it, slide the button to the right until you


to work. With a manual transmission, you must


to work.


in P (Park) or


2-34


To sound the horn, press the pad with the horn symbol on it. The pad is located in the center of the steering wheel. Tilt Wheel (Option)


K2319


A tilt steering wheel allows you to adjust the steering wheel before you drive. level to give your legs more room when You can also raise you exit and enter


it to the highest the vehicle.


K2185


2-35


Features & Contuvls


To tilt the wheel, hold the steering wheel and steering wheel to a comfortable level, then release the lever to in place. Multifunction Lever


pull the lever. Move


the


lock the wheel


The lever on the left side


of the steering column includes


your:


K2239


Turn Signal and Lane Change Indicator Headlight High-Low Beam Windshield Wipers Windshield Washer Cruise Control (Option)


& Passing Signal


236


Turn Signal and Lane Change indicator


. "


.. .


..,." .


K2240


in the direction of the turn


the turn is


up or down. When


or lower the lever until the green arrow


to signal a turn or a lane change.


The turn signal has two upward (for Right) and two downward (for Left) positions. These positions allow you To signal a turn, move the lever all the way finished, the lever will return automatically. A green arrow on the instrument panel will flash or lane change. To signal a lane change, just raise starts to flash. Hold it there until you complete your lane change. The lever will return by itself when you release it. As you signal a normal, a signal bulb may be burned out and other drivers won't see your turn signal. If a bulb arrows don't go on at all when you signal a turn, check the fuse "Fuses" in the Index) and for burned-out bulbs. Operation of Lights Although your vehicle's lighting system (headlights, parking lights, side marker lights and taillights) meet all applicable federal lighting requirements, certain states and provinces may apply their own lighting regulations that may require special attention before you operate these lights. For example, some jurisdictions may require that you operate your lower


if the arrows flash twice as fast as


it to help avoid an accident.


turn or a lane change,


is burned out, replace


If the green (see


fog lamps,


2-37


Features & Contmls


fog lamps at all times, or that headlights be turned on


beam lights with whenever you must use your windshield wipers. prohibit driving solely with parking lights, especially recommended that you check with your own state or provincial highway authority for applicable lighting regulations. Head/ight Hiah-Low Beam F. p .- ..


h*'


In addition, most jurisdictions


at dawn or dusk. It is


K2242


To change the headlights from signal lever all the way toward you. Then release are on, this blue light on the instrument panel


low beam to high or high to


low, pull the turn


it. When the high beams


also will be on.


2-38


Windshield Wipers


K2244


the wiper symbol


to MIST. Hold it there until the


turn the band


let go. The wipers will stop after one cycle. If you want


You control the windshield wipers by turning the band with on it. For a single wiping cycle, wipers start, then more cycles, hold the band on MIST longer. You can set the wiper speed for a long or short delay between wipes. This can be very useful time. The closer For steady wiping at low speed, turn the band away from you position. For high speed wiping, turn wipers, move the band to the


in light rain or snow. Turn to LO, the shorter the delay.


off symbol.


to the LO the band further, to HI. To stop the


the band to choose the delay


A Damaged wiper blades may prevent you from seeing well enough


drive safely. To avoid damage, be sure the wiper blades before using them. windshield, carefully loosen or thaw them. or blade inserts. damaged get new blades


to clear ice and snow from


If they’re frozen to the


If your blades do become


to


Heavy snow or ice can overload your wipers. until the motor cools. Clear away snow


A circuit breaker will stop them


or ice to prevent an overload.


2-39


Features & Controls


Windshield Washer


K2246 PUSH on


At the top of the multifunction lever there’s a paddle with the word it. To spray washer fluid on the windshield, push the paddle. The wipers will clear the window and then either speed. CAUTION - splash can block your vision. You could hit another vehicle or go A * Driving without washer


fluid can be dangerous. A bad mud


stop or return to your preset


off the road. Check your washer In freezing weather, don’t use your washer until the windshield warmed. Otherwise the washer fluid windshield,


fluid level often.


can form ice on the


blocking your vision.


i‘s


2-40


I NOTICE


Cruise Control (Option)


K2247


With Cruise Control, you can maintain a speed or more without keeping your foot on the accelerator. This can really help on long trips. Cruise Control does not work at speeds below about (40 krn/h). When you apply your brakes, or the clutch pedal, transmission, the Cruise Control shuts off.


if you have a manual


of about 25 mph (40 km/h)


25 mph


2-41


CAUTION


I A a steady speed. So, don’t use your Cruise Control on winding


Cruise Control can be dangerous where you can’t drive safely at


roads or in heavy traffic. Cruise Control can be dangerous on slippery roads. On such roads, fast changes spinning, and you could lose control. Don’t on slipPery roads.


in tire traction can cause needless wheel


use Cruise Control


To Set Cruise Control


ON.


Move the Cruise switch to


I CAUTION


If you leave your Cruise Control switch on when you’re not using Cruise, you might hit a button and go into Cruise when you don’t want to. You could be startled and even l o s e control. Keep the Cruise Control switch OFF until vou want to use it.


K2248


Get up to the speed you want. Push in the set button at the end of the lever and release it. Take your foot


off the accelerator pedal.


2-42


To Resume a Set Speed Suppose you set your Cruise Control at a desired speed and then you apply the brake. This, of course, shuts to reset it. Once you’re going about 25 mph (40 kmlh) or more, you can move the Cruise Control switch from ON to WA for about half a second.


off the Cruise Control. But you don’t need


K2249


until you release the switch


will keep going faster You could be startled and even lose control. hold the switch at WA . go faster, don’t


A If you hold the switch at WA longer than half a second, the vehicle To increase Speed While Using Cruise Control There are two ways to go to a higher speed. Here’s the first: to get to the higher speed.


or apply the brake. So unless you want to


the end of the lever, then release the button and the


1. Use the accelerator pedal 2. Push the button at accelerator pedal.


You’ll now cruise at the higher speed.


2-43


Features & Controls


Here's the Second Way to go to a higher speed:


1. Move the Cruise switch from ON to WA. Hold it there until you get up


to the speed you want, and then release the switch.


K2207


2. To increase your speed


in very small amounts, move the switch


for less than three quarters of a second and then release you do this, your vehicle will go about 1 mph (1.6 km/h) faster.


to WA it. Each time


To Reduce Speed While Using Cruise Control


1. Push in the button at the end


speed you want, then release


of the lever until you reach the lower it.


K2260


2-44


2. To slow down


in very small amounts, push the button


a second. Each time you do this, you'll slower.


for less than half go about 1 mph (1.6 kmlh)


foot


Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your off the pedal, your vehicle will slow down to the Cruise Control speed you set earlier. Using Cruise Control on Hills How well your Cruise Control will work load, and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going to a lower gear to keep your speed downhill, you may have down. Of course, of Cruise Control. Many drivers find this to be too much trouble and don't use Cruise Control on steep hills. To Get Out of Cruise Control There are several ways


on hills depends upon your speed,


applying the brake takes you out


to turn off the Cruise Control:


to brake or shift


.Y


1. Step lightly on the brake pedal or push the clutch pedal, if you have


manual transmission; OR


2. Move the Cruise switch


to OFF.


When you turn off the Cruise Control or the ignition, your Cruise Control set speed memory is erased.


2-45


Features & Controls


Headlights and Vehicle Lighting of your instrument panel. Your light switches are on the left side


Push the left side on:


of the switch with the parking lights


symbol on it


to turn


K2250


Parking Lights Sidemarker Lights Taillights License Plate Lights Roof Marker Lights (if you have them) Instrument Panel Lights Transfer Case Shift Indicator Light


Push the left side on the headlights, together with:


of the switch with the master lighting symbol on it


to turn


Parking Lights Sidemarker Lights Taillights License Plate Lights Roof Marker Lights Instrument Panel Lights Transfer Case Shift Indicator Light


(if you have them)


2-46


it to turn off your


to adjust interior lights.


the switch with the 0 symbol on


Push the right side of lights. Turn the dial at the right of the headlight switch Turning the dial all the way up turns on the interior lights. You can switch your headlights from low beam multifunction lever toward you. To return the headlights to lever again. A circuit breaker protects your headlights from electrical overload. an electrical overload, your headlights will flicker happens, have your headlight wiring checked right away. Headlights-On Reminder A buzzer will sound when your headlights are turned in Off, LOCK or Acc. Daytime Running Lights (DRL) Indicator Light (Canada Only)


on and off. If this ever


on and your ignition is


to high by pulling the


low beam, pull the


If you have


K2318


in Canada, you will have this light


sold, when new, It goes on whenever the Daytime Running Lights are


If your vehicle was first on the instrument panel. on. Daytime Running Lights (Canada Only) The Canadian Federal Government has decided that “Daytime Running Lights” (DRL) are a useful feature, in that DRL can make your vehicle more visible to pedestrians and other drivers during daylight hours. DRL are required on new vehicles sold in Canada.


2-47


Features & Controls


The high beam headlights will come on at reduced brightness in Daylight when:


is on The ignition The headlight switch is The parking brake


off, and is released


of DRL again.


off and the exterior


DRL are on. When you turn on your


off the headlights, the exterior lights will go


will change to the reduced brightness


turn on your headlights, the DRL will switch


When you lights come on. When you turn out and the high beams The DRL indicator light on the instrument panel will go on whenever the DRL are on. This light means that only the exterior lights, this light will go out. headlights any time you need to. To idle your vehicle with the DRL stay off until you release the parking brake. Dome Lights The dome lights will come on when you open the doors or tailgate. You also turn the dome lights headlight switch all the way up until it clicks.


off, set the parking brake. The DRL


Of course, you may still turn on


on by turning


the interior light dimmer dial on the


the


will


can


K2360 You can use the dome lamp switch, located below the headlight switch, to set the dome lamps to come on automatically or remain off. To turn the lights off, just press the side automatic operation, press the side marked


of the switch marked OFF. To return the lights


AUTO.


to


2-48


Reading Lights


If you have reading lights, press the bar next to turn the light off. Press the bar again


K2252 to the light to turn the light on.


K2161


If your vehicle has an overhead console with reading lights, they can be swiveled to point button next to the light with the master again to turn the light off.


lighting symbol on it. Press


in the direction you want. To turn the light on, press the


the button


2-49


Underhood Reel Lighf


I L


an underhood reel light.


You may have on the passenger side fender. To use the light, pull up on will unreel as you pull the light.


It is inside the engine compartment


You can use


it as a flashlight.


the release lever and pull the light out. The


cord


using the light, reel the When you are done turning the handle. Then, slide the light into the release lever to lock the light into the holder.


cord back into the housing by holder. Press PUSH on the


K2253


2-50


Mirrors


inside Mirror Push or pull the tab under the mirror to reduce glare from headlights behind you after dark. Outside Mirrors


K2256


Adjust your outside mirrors so you can just see the side of your vehicle, and be folded in to have a clear view of objects behind you. Some mirrors can enter narrow doorways.


K2295


2-5 1


Features & Controls


Convex Outside Mirror Your right side mirror may be convex. you can see more from the driver’s 1 CAUTION


~~


seat.


~ r n


A convex mirror’s surface is curved so


If you aren’t used to a convex mirror, you can hit another vehicle. A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right could hit a vehicle on your right. Check your inside mirror or glance


ov0r your shoulder before chanaine lanes. -


lane, you


Electric Outside Mirrors


If you have electric mirrors, they can be adjusted to point where you want from inside the vehicle. Select the mirror by moving the center located on the driver’s door armrest, mirror angle by pressing the outer arrows on the switch until the mirror is adjusted where you want it.


to R right or L left. Then, adjust the


of the switch,


2-52


Sun Visors To block out glare, you can swing down the visors. You can also swing them out to help block glare from the side.


. .


%.>


’ _


- .~ : .. =,? , ~


~.


K2465


Your visor may have a strap have mirrors on them.


to hold small items, such


as maps. Some visors


Some visors have an extender on the inside edge. When the visor pull the extender out for extra glare coverage at the front Some visors have mirrors with lights. The mirror lights will come lift the mirror cover.


PO284


is down,


or side.


on when you


2-53


Rear Window Wiper and Washer


The rear window wipedwasher switch of the steering wheel.


is on your instrument panel,


K21: to the right


To turn the wiper on, slide the lever


to the lever


to the right.


For delay wiping, slide the lever under control. The wiper will cycle every nine seconds. For steady wiper action, move the slide lever all the way


DELAY to the center of the rear wiper


to the right.


To wash the window, push fluid will continue to spray until the lever is released.


in on the end


of the lever. Window washer


The rear window washer uses the same fluid bottle If the fluid level is low in the washer fluid bottle, you wash your rear window. window, check the


fluid level.


If you can wash your windshield, but not your rear


as the windshield washer.


may not be able


to


2-54


Cigarette Lighter/Ashtras


To use the lighter, push it pop back by itself.


in all the way, and


let go. When it’s ready,


it will


PO286


To remove the rear ashtrays, press down on the inside tabs and pull. Don’t put papers and other things that burn into your ashtrays. cigarettes or other smoking materials could set them on fire, causing damage. Storage Compartments Your vehicle has a variety convenience.


of storage compartments provided for your


If you do,


2-55


Glove Box


To open your glove box, press the button down and pull the door open. Two cup holders are provided for your convenience. Center Floor Console


Your vehicle may have a console compartment between the bucket seats. open it, just squeeze the buttons on both sides Use your round key to lock this compartment. handy place to hold cups.


To of the keyhole, and pull up. Your console also includes a


2-56


Your console also has a cup holder that slides out, for the passengers to use.


back seat


PO1 92


PB002


If your vehicle has a full or split bench seat, you may have attached to the instrument panel. To use the cup holder, pull the handle and slide the cup holder tray out until it stops. Then, let the cup holder swing down into position. all the way in. holder, lift the front and slide the tray


a cup holder


To close the cup


2-57


Center Overhead Console


If you have a garage door opener, the front overhead compartment can be used to conveniently store the opener. open the compartment door by pressing the release button Peel the protective backing the back of your garage door opener, as possible.


from the hook and loop patch. Press


it firmly to as close to the center of the opener


To install the garage door opener, first


forward.


2-58


4


Center the garage door opener activation into place. and press the opener firmly


button over the console door button,


r0059


Use the pegs inside the compartment compartment door will contact Add one peg at a time compartment door closed, when


door to make sure the button on the door opener.


the control button on the garage


until the garage door opener operates with the


you push the button marked PUSH.


2-59


PO223


K2147


The center overhead compartment can be used to conveniently store your sunglasses. To open the compartment, press the release button located at the rear of the compartment door.


The rear overhead compartment can be used book. To open the compartment, press the release button located at the rear of the compartment door.


to store a small item, like a


2-60


Other Storage Compartments


Some vehicles have storage areas for items such as gloves


or small books.


in the instrument panel. Use these spaces


K2238


K2269


Some models have a storage pocket on each use the pocket


to store a variety of small items.


of the front doors. You can


2-61


Features & Controls


fii-


2-62


K2320


X 0 rn "if 0 z


€3 43


L 0


0 5


v)


0, rc 3 U c 3


L a


2-63


K2203


Features & Cuntmls


D 0


0 fn


CD


\ 3


2-64


K2119


4


a0


i.


J -.


2-65


K211B


Featurns & Cuntmls


lnsfrument Cluster Your instrument cluster is designed to let you know at a glance how your. how fast you're going, about how much fuel vehicle is running. You'll know you have, and many other things you'll need to know economically. Tachometer Cluster If you have the tachometer cluster, everything the standard cluster does, engine revolutions per minute (rpm). Speedometer and Odometer


it looks slightly different but will


in addition to displaying the vehicles


to drive safely and


tell you


..


K2322


has


lets you see your speed


in either miles (used in the


in both miles per hour (mph) and


Your speedometer kilometers per hour (km/h). Your odometer shows how far your vehicle U.S.) or kilometers (used in been driven, Canada). Tamper Resistant Odometer Your odometer is tamper-resistant, The odometer will show silver lines between the numbers You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set tien it must be. But on the driver's door to show the old mileage reading when the new odometer was installed.


if it can't, then it's set at zero, and a label must be put


if someone tries to turn it back.


to the mileage total of the old odometer,


2-66


Trip Odometer


zero.


The trip odometer can tell you how far your vehicle has been driven since you last set the trip odometer to To reset the readout. If the reset button all the way back button again to reset the readout to zero. Tachometer


trip odometer, fully press the reset button located near the is not fully pressed, the trip odometer may to zero. If it doesn’t, you may have to press the reset


not go


If you have a tachometer, it displays the engine speed in revolutions per minute (rpm).


K2324


2-67


Features & Controls


Do not operate the engine with the tachometer damage may occur. Damage to your engine or vehicle caused by operating red area isn’t covered by your vehicle warranty.


in the red area, or engine


the engine in the


or others from


it to cause an expensive repair or replacement. Paying


Warning Lights, Gages and lndicafors This part describes the warning lights and gages that are on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before becomes serious enough attention to your warning lights and gages could also save you injury. Warning lights go on when there may be or vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on briefly when you turn the ignition key you know they’re working. alarmed when Gages can indicate when there may be vehicle’s functions. Often gages and warning lights know when there’s a problem with your vehicle. When one of the warning driving, or when one of part that tells you what to Waiting to do repairs can be costly-and even dangerous. know your warning lights and gages. They’re a big help.


lights comes on and stays on when you are


this happens.


work together


the gages shows there may be a problem, check the


do about it. Please follow the manual’s advice.


If you are familiar with this part, you should not be


or is a problem with one of your


is a problem with one of your


to let you

Loading...
x