Erasing HomeLink® Buttons To erase programming from the three buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to flash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds.
2. Release both buttons.
HomeLink® is now in the train (learning) mode and can
be programmed at any time beginning with Step 2
under “Programming HomeLink®” shown earlier in
this section.
Individual buttons cannot be erased, but they can be
reprogrammed. See “Reprogramming a Single
HomeLink® Button” following this section.
Reprogramming a Single HomeLink®
Button
To program a device to HomeLink® using a HomeLink®
button previously trained, follow these steps:
1. Press and hold the desired HomeLink® button.
Do not release the button.
2. The indicator light will begin to flash after
20 seconds. While still holding the HomeLink® button, proceed with Step 2 under “Programming HomeLink®” shown earlier in this section.
Resetting Defaults To reset HomeLink® to default settings do the following: 1. Hold down the two outside buttons for about
20 seconds until the indicator light begins to flash. 2. Continue to hold both buttons until the HomeLink®
indicator light turns off. 3. Release both buttons. For questions or comments, contact HomeLink® at 1-800-355-3515, or on the internet at www.homelink.com. Storage Areas
Glove Box To open the glove box, lift up on the lever. The glove box has a light inside.
Center Console Storage Area The console has cupholders and a cassette tape storage area. To open the console’s storage area, press the latch located toward the front of the console lid on the driver’s side of the vehicle.
Rear Storage Area If your vehicle has the split folding rear seat, there will be two cupholders in the rear seat armrest. To access them, pull down on the cloth strap located toward the top of your center back seat cushion.
Convenience Net The vehicle may have a convenience net located on the back wall of the trunk. Put small loads, like grocery bags, behind the net. It can help keep them from falling over. The net is not for larger, heavier loads. Store those in the trunk as far forward as possible. Unhook the net so that it will lie flat when not in use.
2-37
Sunroof The vehicle may have a sunroof and a sunshade.
The switch is located on the overhead console if the vehicle is equipped with a Driver Information Center (DIC).
DIC Version Shown
If the vehicle is not equipped with a DIC, the sunroof switch is located on the roof panel headliner. The switch works only when the ignition is in ACC, ON or when Retained Accessory Power (RAP) is active.
Open/Express: To activate the express-open feature, press the switch rearward two times. Press the switch forward to stop movement of the sunroof.
Vent: The sunroof also has a vent feature. It can be activated from the closed sunroof position by pressing the switch once rearward. To close, push and hold the sunroof switch forward. When using this feature, the sunshade should be fully opened in the rear position.
The sunshade can be opened manually by sliding it rearward, or automatically, by opening the power sunroof. You will need to close the sunshade manually by sliding it forward.
Close: To close the sunroof, push the switch forward and hold until the sunroof motor stops, or release the switch when the desired position has been reached.
2-38
Vehicle Personalization Some of the convenience features can be reset or customized to perform according to your preference. The features you can program depend upon the options that came with your vehicle. The following list shows features that can be reset or customized along with those options. (cid:127) Settings (Available for All) (cid:127) Engine Oil Life System Reset (Available for All)
Low Tire Pressure Reset
(cid:127) Delayed Headlamp Illumination (Available for All) (cid:127) Automatic Door Lock and Unlock (Available for All) (cid:127) Remote Visual Verification (Available with Remote
Keyless Entry)
(cid:127) Remote Audible Verification (Available with Remote
Keyless Entry)
(cid:127) Content Theft Operation (Available with Content
Theft System) Trunk Jamb (Available with Content Theft System)
(cid:127) Horn Chirp On Timer (Available with Remote
Keyless Entry)
(cid:127) Remote Keyless Entry Transmitter Programming
(Available with Remote Keyless Entry)
(cid:127) Return to Original Factory Settings
(Available for All)
(cid:127) Exit Vehicle Customization Mode Programming Mode To reset or customize the features, first enter the vehicle customization main menu. To enter the main menu, do the following: 1. Turn the ignition to ACC or ON. The radio must
be off.
2. Press and hold the TUNE DISP knob on the
radio for at least five seconds until SETTINGS is displayed.
3. Press the SEEK PSCAN up or down arrows to
scroll through each available feature on your main menu.
4. Press the 1 PREV or 2 NEXT buttons to scroll
through the lower menu. An asterisk (*) will appear next to the item that is the current setting.
The following information shows how to reset or customize features after entering the main menu. SETTINGS (Display Current Settings) This displays all current settings.
2-39
(cid:127) (cid:127) TIRE MON (Tire Inflation Monitor Reset) This feature allows you to reset the tire pressure monitor after checking all tire pressures. See Tires on page 5-59. To clear the LOW TIRE PRESSURE light from the instrument panel cluster and reset the low tire pressure monitor, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until TIRE MON appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. RESET will be displayed.
3. Press the TUNE DISP button to reset. A chime will
be heard to verify the new setting and DONE will be displayed for one second.
The low tire pressure monitor is now reset. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
OIL LIFE (Engine Oil Life System Reset) This feature allows you to reset the engine oil life system after an oil change. See Engine Oil Life System on page 5-22. Be careful not to reset the OIL LIFE system at any time other than when the oil has been changed. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 6-4 and Engine Oil on page 5-18 for more information. To clear the CHANGE ENGINE OIL light from the instrument panel cluster and reset the oil life system, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until OIL LIFE appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. RESET will then be displayed.
3. Press the TUNE DISP knob to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second.
The CHANGE ENGINE OIL light is now reset. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
2-40
LT DELAY (Delayed Headlamp Illumination) This feature allows the vehicle’s headlamps and parking lamps to stay on for a fixed amount of time after you exit the vehicle, or for them to turn off immediately. Programmable Modes
Mode 1: OFF
Mode 2: 30 SEC
Mode 3: 60 SEC Your vehicle was originally programmed to Mode 2. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until LT DELAY appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle.
3. Scroll, using the 1 PREV or 2 NEXT buttons,
through the modes to change the current mode.
4. With your preference displayed, press the TUNE
DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second.
The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. AUTOLOCK (Automatic Door Lock and Unlock) With the ignition in ON and the vehicle’s doors closed, this feature allows for the vehicle doors to automatically lock and unlock when the driver shifts the vehicle’s transaxle into and out of PARK (P), or to turn the feature off. Programmable Modes
Mode 1: OFF
Mode 2: LCK ONLY – Automatic door lock on/automatic door unlock off.
Mode 3: DRVR UNL – Automatic door lock on/automatic door unlock on (driver’s door only).
Mode 4: ALL UNL – Automatic door lock on/automatic door unlock on.
2-41
Your vehicle was originally programmed to Mode 4. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until AUTOLOCK appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle.
3. Scroll, using the 1 PREV or 2 NEXT buttons,
through the modes to change the current mode. 4. With your preference displayed, press the TUNE
DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second.
The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
2-42
FOB LIGHT (Remote Visual Verification) This feature allows the exterior lights to flash when the remote keyless entry transmitter is used to lock or unlock the vehicle, or to program no verification. Programmable Modes
Mode 1: OFF
Mode 2: ON – One flash for each remote lock/two flashes for each remote unlock. Your vehicle was originally programmed to Mode 2. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until FOB LIGHT appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle.
3. Scroll, using the 1 PREV or 2 NEXT buttons,
through the modes to change the current mode. 4. With your preference displayed, press the TUNE
DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. If your vehicle has the optional content theft-deterrent system, the first time a remote UNLOCK command is received, three flashes will be seen and three horn chirps heard to indicate an alarm condition has occurred since last arming. See Content Theft-Deterrent on page 2-14. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
FOB HORN (Remote Audible Verification) This feature allows the horn to chirp when the remote keyless entry transmitter is used to lock or unlock the vehicle, or to program no verification. Programmable Modes
Mode 1: OFF
Mode 2: PARTIAL – One chirp for each remote LOCK command/no chirp for remote UNLOCK command.
Mode 3: FULL – One chirp for each remote LOCK command/two chirps for the first remote UNLOCK command.
2-43
Your vehicle was originally programmed to Mode 2. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until FOB HORN appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle.
3. Scroll, using the 1 PREV or 2 NEXT buttons,
through the modes to change the current mode. 4. With your preference displayed, press the TUNE
DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. If your vehicle has the optional content theft-deterrent system, the first time a remote UNLOCK command is received, three flashes will be seen and three horn chirps heard to indicate an alarm condition has occurred since last arming. See Content Theft-Deterrent on page 2-14. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
2-44
ALARM (Content Theft Operation) This feature allows the content theft-deterrent system to be turned on or off. Programmable Modes
Mode 1: ALRM OFF
Mode 2: ALRM ON Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which your vehicle was programmed may have been changed since it left the factory. To determine the mode to which your vehicle is programmed or to program your vehicle to a different mode, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until ALARM appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle.
3. Scroll, using the 1 PREV or 2 NEXT buttons,
through the modes to change the current mode. 4. With your preference displayed, press the TUNE
DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second.
The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. TRNKJAMB (Trunk Jamb) This feature allows the content theft system trunk lock sensor to be disabled or enabled. Programmable Modes
Mode 1: TRNK OFF
Mode 2: TRNK ON
Your vehicle was originally programmed to Mode 2. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until TRNKJAMB appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle.
3. Scroll, using the 1 PREV or 2 NEXT buttons,
through the modes to change the current mode. 4. With your preference displayed, press the TUNE
DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second.
The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
2-45
CHIRP (Horn Chirp Timer) This feature allows you to choose between short or long horn chirp sounds when the remote keyless entry transmitter is used. Programmable Modes
Mode 1: SHORT
Mode 2: LONG Your vehicle was originally programmed to Mode 1. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until CHIRP appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle.
3. Scroll, using the 1 PREV or 2 NEXT buttons,
through the modes to change the current mode.
4. With your preference displayed, press the TUNE
DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second.
The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. ORIG. SET (Return to the Original Settings) This feature allows you to return all customization feature settings back to their original factory settings. To reset, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until ORIG. SET appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. SET ALL will appear.
3. With your preference displayed, press the TUNE
DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. The original factory settings are now reset. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
2-46
EXIT (Exit Feature Customization Mode) This feature allows you to exit the vehicle customization programming. To exit, do the following: (cid:127) Scroll until EXIT appears on the display. (cid:127) Press the TUNE DISP button to exit programming.
A chime will be heard to verify the exit.
FOB PROG (Remote Keyless Entry Transmitter Programming) This feature allows you to match the remote keyless entry transmitter to your vehicle. To match the transmitter, do the following: 1. Scroll, using the SEEK PSCAN up or down arrows,
until FOB PROG appears on the display.
2. Press the 1 PREV or 2 NEXT button to enter the
submenu. BEGIN will be displayed.
3. Press the TUNE DISP button to start programming. When the message PUSH FOB flashes, press and hold the LOCK and UNLOCK buttons on the first transmitter at the same time for 15 seconds. A chime will be heard to verify the transmitter is learned.
4. Repeat Step 3 for each additional transmitter. The transmitter is programmed now. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
2-47
✍ NOTES
2-48
Section 3
Instrument Panel
Instrument Panel Overview ...............................3-4
Hazard Warning Flashers ................................3-6
Other Warning Devices ...................................3-6
Horn .............................................................3-6
Tilt Wheel
.....................................................3-6
Turn Signal/Multifunction Lever .........................3-7
Turn and Lane-Change Signals ........................3-7
Headlamp High/Low-Beam Changer ..................3-8
Flash-to-Pass .................................................3-8
Windshield Wipers ..........................................3-9
Windshield Washer .......................................3-10
Cruise Control ..............................................3-11
Exterior Lamps .............................................3-14
Delayed Headlamps ......................................3-15
Daytime Running Lamps (DRL)/Automatic
Headlamp System .....................................3-15
Fog Lamps ..................................................3-16
Interior Lamps ..............................................3-16
Instrument Panel Brightness ...........................3-19
Courtesy Lamps ...........................................3-19
Dome Lamp .................................................3-19
Entry Lighting ...............................................3-19
Delayed Entry Lighting ...................................3-20
Delayed Exit Lighting .....................................3-20
Parade Dimming ...........................................3-20
Reading Lamps ............................................3-20
Battery Run-Down Protection ..........................3-21
Accessory Power Outlets ...............................3-21
Ashtrays and Cigarette Lighter ........................3-22
Climate Controls ............................................3-23
Dual Climate Control System ..........................3-23
Outlet Adjustment .........................................3-26
Passenger Compartment Air Filter ...................3-27
Warning Lights, Gages, and Indicators ............3-28
Instrument Panel Cluster ................................3-29
Speedometer and Odometer ...........................3-32
Trip Odometer ..............................................3-32
Tachometer .................................................3-32
Safety Belt Reminder Light .............................3-32
Airbag Readiness Light ..................................3-33
Voltmeter Gage ............................................3-34
Brake System Warning Light ..........................3-34
Anti-Lock Brake System Warning Light .............3-35
Traction Control System (TCS)
Warning Light ...........................................3-36
Engine Coolant Temperature Gage ..................3-36
Malfunction Indicator Lamp .............................3-37
Engine Oil Pressure Gage .............................3-40
Cruise Control Light ......................................3-41
Highbeam On Light .......................................3-41
Fuel Gage ...................................................3-42
3-1
Section 3
Instrument Panel
Message Center .............................................3-42
Service Traction System Warning Message ......3-43
Traction Active Message ................................3-43
Battery Warning Message ..............................3-44
Hot Coolant Temperature Warning Message .....3-44
Low Oil Pressure Message ............................3-45
Low Engine Oil Level Message .......................3-45
Change Engine Oil Message ..........................3-46
Low Tire Message ........................................3-46
Door Ajar Warning Message ...........................3-47
Trunk Ajar Warning Message .........................3-47
Security Message .........................................3-48
Low Washer Fluid Warning Message ...............3-48
Low Fuel Warning Message ...........................3-49
Low Brake Fluid Warning Message .................3-49
Service Vehicle Soon Message .......................3-50
Highbeam Out Warning Message ....................3-50
Driver Information Center (DIC) .......................3-51
Trip Computer ................................................3-53
Audio System(s) .............................................3-54
Setting the Time ...........................................3-54
Radio with Cassette ......................................3-55
Radio with CD ..............................................3-66
Radio with Cassette and CD ..........................3-76
Theft-Deterrent Feature ..................................3-88
Audio Steering Wheel Controls .......................3-89
Radio Reception ...........................................3-90
Care of Your Cassette Tape Player .................3-90
Care of Your CDs .........................................3-91
Care of Your CD Player ................................3-91
Backglass Antenna .......................................3-92
XM™ Satellite Radio Antenna System .............3-93
Vehicle Customization Settings .......................3-93
Chime Level Adjustment ................................3-93
3-2
✍ NOTES
3-3
Instrument Panel Overview
3-4
The main components of your instrument panel are listed here:
A. Instrument Panel Fuse Block. See “Instrument Panel
Fuse Block” under Fuses and Circuit Breakers on page 5-97.
B. Turn Signal/Multifunction Lever. See Turn
Signal/Multifunction Lever on page 3-7.
C. Audio Steering Wheel Controls (If Equipped). See
Audio Steering Wheel Controls on page 3-89.
D. Instrument Panel Cluster. See Instrument Panel
Cluster on page 3-29.
E. Hazard Warning Flasher Button. See Hazard
Warning Flashers on page 3-6.
F. Audio System. See Audio System(s) on page 3-54. G. Air Outlet. See “Outlet Adjustment” under Dual
Climate Control System on page 3-23.
H. Exterior Lamps Control. See Exterior Lamps on
page 3-14.
I. Remote Trunk Release. See “Remote Trunk
Release” under Trunk on page 2-10.
J. Tilt Steering Wheel Lever. See Tilt Wheel on
page 3-6.
K. Hood Release. See Hood Release on page 5-11. L. Steering Wheel Cruise Control (If Equipped).
See Cruise Control on page 3-11.
M. Ignition Switch. See “Ignition Positions” under New
Vehicle Break-In on page 2-16.
N. Automatic Transaxle Shift Lever. See Automatic
Transaxle Operation on page 2-20.
O. Climate Controls. See Dual Climate Control System
on page 3-23.
P. Glove Box. See Glove Box on page 2-37.
3-5
Horn Press near or on the horn symbols on your steering wheel pad to sound the horn.
Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you enter and exit the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column.
To tilt the wheel, hold the wheel and pull the lever. Then move the wheel to a comfortable position and release the lever to lock the wheel in place.
Hazard Warning Flashers Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off.
The hazard warning flasher button is located near the center of the instrument panel.
Your hazard warning flashers work no matter what position your key is in, and even if the key is not in. Press the button to make the front and rear turn signal lamps flash on and off. Press the button again to turn the flashers off. When the hazard warning flashers are on, your turn signals will not work. Other Warning Devices If you carry reflective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle.
3-6
Turn Signal/Multifunction Lever
Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.
An arrow on the instrument panel cluster will flash in the direction of the turn or lane change.
The lever located on the left side of the steering column includes the following:
Turn Signal and Lane-Change Signals
(cid:127) Headlamp High/Low-Beam Changer
Flash-to-Pass Feature
(cid:127) Windshield Wipers (cid:127) Windshield Washer For information on the exterior lamps, see “Exterior Lamps” later in this section.
To signal a lane change, raise or lower the lever until the arrow starts to flash. Hold it there until you complete your lane change. The lever will return by itself when you release it. If the arrow flashes faster than normal as you signal a turn or a lane change, a signal bulb may be burned out and other drivers won’t see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows don’t go on at all when you signal a turn, check for burned-out bulbs and then check the fuse. See Fuses and Circuit Breakers on page 5-97.
3-7
(cid:127) (cid:127) Turn Signal On Chime If you leave either one of your turn signals on and drive more than three-quarters of a mile (1.2 km), a chime will sound to alert you. Headlamp High/Low-Beam Changer To change your headlamps from low beams to high beams, or from high to low, pull the multifunction lever all the way toward you. Then release it.
Flash-to-Pass With the turn signal lever in the low-beam position, pull the lever toward you momentarily to switch to high-beam, (to signal you are going to pass). If the headlamps are on, they will return to low-beam when the lever is released. This feature operates even if the headlamps are off.
While the high beams are on, this light will appear on the instrument panel cluster.
This light works only while the key is in ON. The fog lamps (if equipped) are not illuminated when the high beams are on.
3-8
Windshield Wipers
The windshield wipers will operate when the ignition is in ACC or ON.
WIPER: To operate the windshield wipers, turn the band labeled WIPER, located on the multifunction lever, upward or downward.
OFF: To stop the wipers, turn the band to OFF.
The five marks between OFF and LO are delay settings. For a longer delay between wiping cycles, turn the band downward. For a shorter delay between wiping cycles turn the band upward.
LO (Low Speed): Turn the band upward to LO for steady wiping at a low speed.
HI (High Speed): Turn the band upward to HI for steady wiping at high speed.
MIST: Turn the band downward to MIST for a single
wiping cycle. Hold the band at this setting until the
windshield wipers start, then release it. The windshield
wipers will stop after one wipe. If additional cycles
are needed, hold the band on MIST longer.
Be sure to clear ice and snow from the wiper blades
before using them. If they’re frozen to the windshield,
carefully loosen or thaw them. If your blades become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload. If your blades
become damaged, get new blades or blade inserts. See
Windshield Wiper Blade Replacement on page 5-58
for more information.
3-9
Windshield Washer At the top of the multifunction lever, there’s a paddle with the windshield washer symbol and the word PUSH on it. To spray washer fluid on the windshield, push the paddle. The wipers will run for several sweeps and then either stop or return to your preset speed. The ignition key must be in ACC or ON for this to work. See Windshield Washer Fluid on page 5-43.
{CAUTION:
In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.
United States
Canada
When you are low on washer fluid, the LOW WASHER FLUID message will be illuminated in the message center for 60 seconds. When the ignition is turned off, this message will appear again for three seconds as a reminder that the fluid level is low. Until the fluid tank is refilled, every time you start your vehicle, the LOW WASHER FLUID message will be illuminated in the message center for 60 seconds. Be sure to check the fluid level and refill the tank right away.
3-10
Cruise Control If your vehicle is equipped with cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When you apply your brakes, the cruise control shuts off.
{CAUTION:
Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads.
If your vehicle is in cruise control when the traction control system (optional) begins to limit wheel spin, the cruise control will automatically disengage. See Traction Control System (TCS) on page 4-8. When road conditions allow you to safely use it again, you may turn the cruise control back on.
3-11
Setting Cruise Control
{CAUTION:
If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
2. Get up to the speed you want. 3. Press SET located on your steering wheel and
release it.
4. Take your foot off the accelerator. The CRUISE light on the instrument panel cluster will come on after the cruise control has been set to the desired speed. Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course shuts off the cruise control. But you don’t need to reset it.
1. Push the CRUISE
ON/OFF button located on the steering wheel to turn the cruise control on.
Once you’re going about 25 mph (40 km/h) or more, press RES (Resume) on your steering wheel. You’ll go right back up to your chosen speed and stay there.
3-12
Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:127) Use the accelerator pedal to get to the higher speed. Press SET on the steering wheel, then release the button and the accelerator pedal. You’ll now cruise at the higher speed.
(cid:127) Press ACC (Accelerate) on the steering wheel. Hold it there until you get up to the speed you want and then release the button. To increase your speed in very small amounts, press ACC briefly and then release it. Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster.
The accelerate feature will only work after you set the cruise control speed by pressing SET on the steering wheel. Reducing Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control: (cid:127) Press COAST on the steering wheel until you reach
the lower speed you want, then release it. To slow down in very small amounts, press COAST on the steering wheel briefly. Each time you do this, you’ll go about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers find this to be too much trouble and don’t use cruise control on steep hills. Ending Cruise Control There are two ways to cancel the cruise control: (cid:127) Step lightly on the brake pedal. (cid:127) Press CRUISE ON/OFF on the steering wheel. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased.
3-13
(cid:127) Exterior Lamps
The exterior lamps control is located on the instrument panel to the left of the steering wheel.
3-14
It controls the following systems: (cid:127) Headlamps
Taillamps
(cid:127) Parking Lamps
License Plate Lamps Instrument Panel Lights
The exterior lamps control has three positions:
Off: Push the control all the way in to turn off the exterior lamps.
Parking Lamps: Pull the control out halfway to turn on the parking lamps together with the following:
Taillamps License Plate Lamps Instrument Panel Lights
Headlamps: Pulling the control all the way out turns on the headlamps together with the previously listed lamps and lights. A warning chime will sound if you open the driver’s door when the ignition switch is off and the headlamps are on.
(cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Delayed Headlamps The delayed headlamps feature provides a period of exterior lighting as you leave the area around your vehicle. The feature is activated when the headlamps are on due to the automatic headlamps control feature later described in this section, and when the ignition is turned off. Your headlamps will then remain on until the exterior lamps control is moved to the parking lamps position or until either a 30 second or 60 second lighting period has ended. If you turn off the ignition with the headlamps switch in the parking lamps or headlamps position, the delayed headlamps cycle will not occur. To disable the delayed headlamps feature or change the time of delay, see Vehicle Customization Settings on page 3-93.
Daytime Running Lamps (DRL)/Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles first sold in Canada.
A light sensor on top of the instrument panel makes the DRL work, so be sure it isn’t covered. The DRL system’s automatic headlamp control will make your low-beam headlamps come on at a reduced brightness when the following conditions are met:
The ignition is ON, the exterior lamps control is OFF and the gearshift is not in PARK (P).
When the DRL are on, only your low-beam headlamps, at a reduced level of brightness, will be on. The headlamps, taillamps, sidemarker and other lamps won’t be on. Your instrument panel and cluster won’t be lit up either. When it’s dark enough outside, your low-beam headlamps will turn off and the headlamps and parking lamps will turn on. The other lamps that come on with your headlamps will also come on. When it’s bright enough outside, your headlamps will go off and your DRL will come on. As with any vehicle, you should turn on the regular headlamps system when you need it.
3-15
(cid:127) (cid:127) (cid:127) Interior Lamps Instrument Panel Brightness The knob for the instrument panel light is located on the exterior lamps control. Pull the knob out halfway and then turn the knob clockwise to brighten or counterclockwise to dim the lights. Courtesy Lamps When a door is opened, the courtesy lamps automatically come on. They make it easy for you to enter and leave your vehicle. You can also manually turn these lamps on by turning the exterior lamps control clockwise all the way to DOME. The reading lamps, located on the rearview mirror, can be turned on or off independent of the automatic courtesy lamps, when the doors are closed.
Fog Lamps
If your vehicle has this feature, the fog lamp button is located on the instrument panel, next to the exterior lamp control wheel, to the left of the steering column.
To turn the fog lamps on, press the FOG button. A light will glow in the button to let you know that the fog lamps are on. Press the FOG button again to turn the fog lamps off. The ignition must be in ON and your parking lamps must be on for your fog lamps to work. The fog lamps will go off while you change to high-beam headlamps.
3-16
Entry Lighting Your vehicle may have the entry lighting feature. Your courtesy lamps will come on and stay on for a set time whenever you press UNLOCK on the remote keyless entry transmitter. If you open a door, the lamps will stay on while it’s open and then turn off automatically about 25 seconds after you close it. If you press UNLOCK and don’t open a door, the lamps will turn off after about 40 seconds. Illuminated entry includes a feature called theater dimming. With theater dimming, the lamps don’t just turn off at the end of the delay time. Instead, they slowly dim after the delay time until they go out. The delay time is canceled if you turn the ignition key to ON or press the power door lock switch. When the ignition is on, illuminated entry is inactive, which means the courtesy lamps won’t come on unless a door is opened. Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed.
The ignition must be off for delayed entry lighting to work. Immediately after both doors have been closed, the delayed entry lighting feature will continue to work until one of the following occurs:
The ignition is moved to ON, the doors are locked or an illumination period of 25 seconds has elapsed.
If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on. Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. The vehicle’s ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination will activate and remain on until one of the following occurs:
The ignition is moved to ON, the power door locks are activated or an illumination period of 25 seconds has elapsed.
If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on.
3-17
(cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Parade Dimming The instrument panel has an added feature called parade dimming. This feature prohibits the dimming of your instrument panel displays during the daylight while the headlamps are on so that you’ll still be able to see the displays. Reading Lamps The reading lamps are located on the rearview mirror. These lamps and the interior courtesy lamps come on when any door is opened. Press the button to turn them on and off while the doors are closed. Dome Lamp The dome lamp will come on when you open a door. You can also turn this lamp on by turning the exterior lamp control clockwise to DOME.
Battery Rundown Protection Your vehicle has a feature to help prevent you from draining the battery in case you accidentally leave on the interior courtesy lamps, reading/map lamps, visor vanity lamps, trunk lamp or glove box lamps. If you leave any of these lamps on, they will automatically turn off after 10 minutes, if the ignition is off. The lamps won’t come back on again until you do the following:
Turn the ignition on or turn the exterior lamps control off, then on again.
If your vehicle has less than 15 miles (25 km) on the odometer, the battery saver will turn off the lamps after only three minutes. Battery rundown protection will also work if the headlamps are left on. After having been left on for 10 minutes, the headlamps and the parking lamps will flash three times. They will remain on for one more minute before turning off automatically.
3-18
(cid:127) (cid:127) Instrument Panel Brightness The knob for the instrument panel light is located on the exterior lamps control. Pull the knob out halfway and then turn the knob clockwise to brighten or counterclockwise to dim the lights.
Courtesy Lamps When a door is opened, the courtesy lamps automatically come on. They make it easy for you to enter and leave your vehicle. You can also manually turn these lamps on by turning the exterior lamps control clockwise all the way to DOME. The reading lamps, located on the rearview mirror, can be turned on or off independent of the automatic courtesy lamps, when the doors are closed.
Dome Lamp The dome lamp will come on when you open a door. You can also turn this lamp on by turning the exterior lamp control clockwise to DOME.
Entry Lighting Your vehicle may have the entry lighting feature. Your courtesy lamps will come on and stay on for a set time whenever you press UNLOCK on the remote keyless entry transmitter. If you open a door, the lamps will stay on while it’s open and then turn off automatically about 25 seconds after you close it. If you press UNLOCK and don’t open a door, the lamps will turn off after about 40 seconds. Illuminated entry includes a feature called theater dimming. With theater dimming, the lamps don’t just turn off at the end of the delay time. Instead, they slowly dim after the delay time until they go out. The delay time is canceled if you turn the ignition key to ON or press the power door lock switch. When the ignition is on, illuminated entry is inactive, which means the courtesy lamps won’t come on unless a door is opened.
3-19
Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after both doors have been closed, the delayed entry lighting feature will continue to work until one of the following occurs:
The ignition is ON, the doors are locked or an illumination period of 25 seconds has elapsed.
If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on.
Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. The vehicle’s ignition must be off for delayed exit lighting to work.
When the key is removed, interior illumination will activate and remain on until one of the following occurs:
The ignition is ON, the power door locks are activated or an illumination period of 25 seconds has elapsed.
If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on.
Parade Dimming The instrument panel has an added feature called parade dimming. This feature prohibits the dimming of your instrument panel displays during the daylight while the headlamps are on so that you’ll still be able to see the displays.
Reading Lamps The reading lamps are located on the rearview mirror. These lamps and the interior courtesy lamps come on when any door is opened. Press the button to turn them on and off while the doors are closed.
3-20
(cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Battery Run-Down Protection Your vehicle has a feature to help prevent you from draining the battery in case you accidentally leave on the interior courtesy lamps, reading/map lamps, visor vanity lamps, trunk lamp or glove box lamps. If you leave any of these lamps on, they will automatically turn off after 10 minutes, if the ignition is off. The lamps won’t come back on again until you do the following:
Turn the ignition ON or turn the exterior lamps control off, then on again.
If your vehicle has less than 15 miles (25 km) on the odometer, the battery saver will turn off the lamps after only three minutes. Battery rundown protection will also work if the headlamps are left on. After having been left on for 10 minutes, the headlamps and the parking lamps will flash three times. They will remain on for one more minute before turning off automatically.
Accessory Power Outlets Your vehicle has a 12-volt outlet which can be used to plug in electrical equipment such as a cellular telephone, a compact disc player, etc.
It is located at the rear of the console.
Lift the cover to access the outlet. When not using the outlet, make sure the protective cover is in place. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating.
3-21
(cid:127) (cid:127) Certain accessory power plugs may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem see your dealer for additional information on the accessory power plugs. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Check with your dealer before adding electrical equipment, and never use anything that exceeds the amperage rating. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only.
Improper use of the power outlet can cause
If you put papers or other flammable items
Ashtrays and Cigarette Lighter Notice: in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put flammable items in the ashtray. Your vehicle may have a cigarette lighter and ashtray located on the console. The ashtray is removable and has a cupholder and liner underneath. To remove the ashtray, lift it up with the liner and pull it out. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Do not use anything other than the cigarette lighter in the heating element. To activate the cigarette lighter, push it into the heating element. When the lighter is ready it will pop out.
3-22
Climate Controls
Dual Climate Control System With this system you can control the heating, cooling, defrost, defog and ventilation for your vehicle.
Manual Operation Turn the right knob clockwise or counterclockwise to direct the airflow inside of your vehicle. To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets. ) (Bi-Level): This mode allows for approximately a 50/50 split of air to the instrument panel outlets and to the floor outlets. 6 (Floor): This mode directs most of the air to the floor outlets, with some of the air directed to the windshield and side window outlets. In this mode, the system will automatically select Outside Air. The right knob can also be used to select defog or defrost mode. For more information, see “Defogging and Defrosting” later in this section. By positioning the right knob between two modes, a combination of those two modes is selected. It should be noted, that the air conditioning compressor will be engaged unless the outside temperature is 40°F (4°C) or below. Recirculation cannot be selected when in Floor Mode.
3-23
9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. If the airflow seems low when the fan is at the highest setting, the passenger compartment air filter, if equipped, may need to be replaced. For more information, see Passenger Compartment Air Filter on page 3-27 and Scheduled Maintenance on page 6-4. : (Outside Air): Press this button to turn the outside air mode on. When this mode is on, outside air will circulate throughout your vehicle. When the button is pressed, an indicator light in the button will come on to let you know that it is activated. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode.
You may have to set the instrument panel brightness control to the highest setting during the day to see the indicator lamp.
? (Recirculation): This mode keeps outside air from coming in the vehicle. It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly. Press this button to turn the recirculation mode on. When the button is pressed, an indicator light will come on.
You may have to set the instrument panel brightness control to the highest setting during the day to see the indicator lamp.
The recirculation mode cannot be used with outside air modes.
D or P (Temperature Control): Slide the levers marked D (Driver) or P (Passenger) to increase or decrease the temperature on the driver’s side or the passenger’s side of the vehicle.
3-24
# (Air Conditioning): Press this button to turn the air conditioning system on or off. When A/C is pressed, an indicator light will come on to let you know that the air conditioning has been activated.
You may have to set the instrument panel brightness control to the highest setting during the day to see the indicator lamp. On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for your vehicle to cool down. It also helps the system to operate more efficiently. For quick cool down on hot days, do the following: 1. Select the vent mode. 2. Select the recirculation mode. 3. Select A/C. 4. Select the coolest temperature for both zones. 5. Select the highest fan speeds. Using these settings together for long periods of time may cause the air inside of your vehicle to become too dry. To prevent this from happening, after the air inside of your vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal.
Defogging and Defrosting Fog on the inside of the windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. Turn the right knob clockwise to select the defog or defrost mode. - (Defog): This mode directs air equally to the windshield and the floor outlets. When you select this mode, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is below 40°F (4°C). The recirculation mode cannot be selected while in the defog mode. Do not drive the vehicle until all the windows are clear. 0 (Defrost): This mode directs half of the air to the windshield and side window vents and half to the floor vents. In this mode, the system will automatically force outside air into your vehicle. The recirculation mode cannot be selected while in the defog mode. The air conditioning compressor will run automatically in this setting, unless the outside temperature is below 40°F (4°C). Do not drive the vehicle until all the windows are clear.
3-25
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. <: The rear window defogger will turn off approximately 20 minutes after the button is pressed. If turned on again, the defogger will run for the same amount of time. The defogger can also be turned off by pressing the button again or by turning off the engine.
Do not drive the vehicle until all the windows are clear. If your vehicle has heated outside rearview mirrors, the mirrors will heat to help clear fog or frost from the surface of the mirror when the rear window defog button is pressed. Notice: Don’t use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs wouldn’t be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid.
Outlet Adjustment Use the knob located below or to the side of the outlet, to change the direction of the air flow. Operation Tips (cid:127) Clear away any ice, snow or leaves from the air
inlets at the base of the windshield that may block the flow of air into your vehicle.
(cid:127) Use of non-GM approved hood deflectors may adversely affect the performance of the system.
(cid:127) Keep the path under the front seats clear of objects
to help circulate the air inside your vehicle more effectively. If the airflow seems low when the fan is at the highest setting, the passenger compartment air filter, if equipped, may need to replaced. For more information, see Passenger Compartment Air Filter on page 3-27 and Scheduled Maintenance on page 6-4.
3-26
(cid:127) Passenger Compartment Air Filter Your vehicle may be equipped with a passenger compartment particulate air filter. It is located underneath the hood just below the windshield wiper arm on the passenger’s side of the vehicle, underneath the air inlet grille. The filter traps most of the pollen from air entering the Climate Control System. Like your engine’s air cleaner/filter, it may need to be changed periodically to ensure system performance. For information on how often to change the passenger compartment air filter, see Scheduled Maintenance on page 6-4. To change the passenger compartment air filter, use the following steps: 1. Turn off the ignition when the windshield wipers are
in the up position.
2. Raise the vehicle hood. 3. Disconnect the windshield washer pump hose from
the fender rail and air inlet grille.
4. Peel back the hood weatherstrip from the
passenger’s side of the vehicle halfway to center.
5. Remove the air inlet grille retainers. 6. Remove the air inlet grille. 7. Remove the old passenger compartment air filter. 8. Reverse the steps to install the new air filter. For the type of filter to use, see Normal Maintenance Replacement Parts on page 6-13.
3-27
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on briefly when you start the engine just to let you know they’re working. If you are familiar with this section, you should not be alarmed when this happens.
Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there’s a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly – and even dangerous. So please get to know your warning lights and gages. They’re a big help. Your vehicle may also have a Driver Information Center (DIC) that works along with the warning lights and gages. See Driver Information Center (DIC) on page 3-51.
3-28
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel is in your tank and many other things you need to drive safely and economically.
Uplevel 3400 V6 Engine Cluster: United States version with ABS and Traction Control shown, Canada similar
3-29
Uplevel 3800 V6 Engine Cluster: United States version with ABS and Traction Control shown, Canada similar
3-30
Uplevel 3800 Supercharged V6 Engine Cluster: United States version with ABS and Traction Control shown,
Canada similar
3-31
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven in either miles (used in the United States) or in kilometers (used in Canada). Your vehicle has a tamper-resistant odometer. If you see ERROR, you’ll know someone has probably tampered with it and the numbers may not be accurate. You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set to the mileage total of the old odometer, then that will be done. But if it can’t, then it will be set at zero and a label must be put on the driver’s door to show the old mileage reading when the new odometer was installed.
Trip Odometer Your trip odometer tells how far you have driven since you last reset it. Your trip/select reset switch will go back and forth between the odometer and the trip odometer if the button is pressed and released within 1.5 seconds. If the button is pressed and held for longer than 1.5 seconds while in the trip odometer mode, it will be reset to zero.
3-32
If the button is pressed and held for longer than 1.5 seconds while in the odometer mode, it will have no effect. Your trip odometer will work no matter what position your key is in, and even if the key isn’t in.
Tachometer The tachometer displays the engine speed in thousands of revolutions per minute (rpm).
Safety Belt Reminder Light When the key is turned to ON, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled.
The safety belt light will also come on and stay on for several seconds, then it will flash for several more.
Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-46.
This light will come on when you start your vehicle, and it will flash for a few seconds. Then the light should go out. This means the system is ready.
If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away.
{CAUTION:
If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inflate in a crash, or they could even inflate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle.
The airbag readiness light should flash for a few seconds when you turn the ignition key to ON. If the light doesn’t come on then, have it fixed so it will be ready to warn you if there is a problem.
3-33
Voltmeter Gage
If your vehicle is equipped with the 3800 V6 engine it has a voltmeter gage that indicates battery voltage.
Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part isn’t working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. The LOW BRAKE FLUID message in the message center will also appear when there is a brake problem. See Low Brake Fluid Warning Message on page 3-49. Have your brake system inspected right away.
If the gage reads less than 12 volts or more than 16 volts while the engine is running, and it stays there, you may have a problem with the electrical charging system. Also, when your gage reads less than 11 volts or more than 16 volts, your battery life indicator will be illuminated in the message center. For more information see Battery Warning Message on page 3-44.
United States
Canada
This light should come on briefly when you turn the ignition key to ON. If it doesn’t come on then, have it fixed so it will be ready to warn you if there’s a problem.
3-34
When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push. Or, the pedal may go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Brake System Warning Light on page 3-34 and Towing Your Vehicle on page 4-34.
{CAUTION:
Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service.
Anti-Lock Brake System Warning Light
If your vehicle has ABS, the anti-lock brake system warning light will come on for a few seconds when you turn the ignition key to ON.
If the anti-lock brake system warning light stays on longer than normal after you’ve started your engine, turn the ignition off. Or, if the light comes on and stays on when you’re driving, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the light still stays on, or comes on again while you’re driving, the anti-lock brake system needs service and you don’t have anti-lock brakes. The anti-lock brake system warning light will come on briefly when you turn the ignition key to ON. This is normal. If the light doesn’t come on then, have it fixed so it will be ready to warn you if there is a problem.
3-35
Traction Control System (TCS) Warning Light
Engine Coolant Temperature Gage
If your vehicle has the traction control system, this warning light may come on for the following reasons:
If you turn the system off by pressing the TRAC OFF button located on the center console, a chime will sound and the warning light will come on and stay on. To turn the system back on, press the button again. The warning light should go off. See Traction Control System (TCS) on page 4-8 for more information. If there’s a brake system problem that is specifically related to traction control, the traction control system will turn off and the warning light will come on. If your brakes begin to overheat, the traction control system will turn off and the warning light will come on until your brakes cool down.
United States - 3400 V6
Engine Cluster
United States - 3800 V6
Engine Cluster
If the traction control system warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service.
Canada - 3400 V6
Engine Cluster
Canada - 3800 V6
Engine Cluster
This gage shows the engine coolant temperature.
3-36
(cid:127) (cid:127) It also provides an indicator of how hard your vehicle is working. During the majority of the operation, the gage will read 210°F (100°C) or less. If you are pulling a load or going up hills, it is normal for the temperature to fluctuate and approach the 250°F (122°C) mark. When the gage reads greater than 250°F (122°C), the HOT COOLANT TEMP light will be illuminated in the message center and a chime will sound continuously. If the gage reaches the 260°F (125°C) mark, it indicates that the cooling system is working beyond its capacity. See Engine Overheating on page 5-32. Malfunction Indicator Lamp Check Engine Light
United States
Canada
Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems.
If you keep driving your vehicle with this
This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The CHECK ENGINE light comes on to indicate that there is a problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. Notice: light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. Notice: Modifications made to the engine, transaxle, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and may cause this light to come on. Modifications to these systems could lead to costly repairs not covered by your warranty. This may also result in a failure to pass a required Emission Inspection/Maintenance test.
3-37
This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways:
Light Flashing — A misfire condition has been detected. A misfire increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required. Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service may be required.
If the Light Is Flashing The following may prevent more serious damage to your vehicle: (cid:127) Reducing vehicle speed (cid:127) Avoiding hard accelerations (cid:127) Avoiding steep uphill grades
If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible
If the light stops flashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park your vehicle. Turn the key off, wait at least 10 seconds and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still flashing, follow the previous steps, and see your dealer for service as soon as possible.
3-38
(cid:127) (cid:127) (cid:127) If the Light Is On Steady You also may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling Your Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap will allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off.
Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. (These conditions may go away once the engine is warmed up.) This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that may have developed.
3-39
Engine Oil Pressure Gage
The oil pressure indicator tells you if you have the correct oil pressure in your engine to operate your vehicle.
3800 V6 Engine
Under normal conditions the indicator should read slightly above the half way point.
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the Check Engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This may take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your GM dealer can prepare the vehicle for inspection.
3-40
If your oil pressure falls too low, the indicator will read at the low setting and you should have your vehicle serviced immediately.
{CAUTION:
Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches fire. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced.
Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil.
Cruise Control Light
The CRUISE light comes on whenever you set your cruise control. See Cruise Control on page 3-11.
Highbeam On Light
This light will illuminate when the headlamp high beams are in use.
See Headlamp High/Low-Beam Changer on page 3-8.
3-41
Fuel Gage
United States - 3400 V6
Engine Cluster
United States - 3800 V6
Engine Cluster
Canada - 3400 V6
Engine Cluster
Canada - 3800 V6
Engine Cluster
3-42
The fuel gage, when the ignition is on, tells you about how much fuel you have left in your tank. The gage will first indicate empty before you are out of fuel, and you should get more fuel as soon as possible. Here are four situations you may experience with your fuel gage. None of these indicate a problem with the fuel gage. (cid:127) At the gas station, the fuel pump shuts off before
the gage reads full. It takes a little more or less fuel to fill up than the fuel gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to fill the tank. The gage goes back to empty when you turn off the ignition. The gage pointer may move while cornering, braking or accelerating. Message Center The message center is located below the tachometer gage on the instrument panel cluster. It gives you important safety and maintenance facts.
(cid:127) (cid:127) (cid:127) Service Traction System Warning Message
Traction Active Message
United States
Canada
If your vehicle is equipped with the traction control system, this message will stay on a few seconds after the traction system stops limiting wheel spin. This message will appear when the traction control system is limiting wheel spin.
United States
Canada
If your vehicle is equipped with the traction control system and this message appears when you are driving, there is a problem with your traction control system and your vehicle is in need of service. When this message is displayed, the system will not limit wheel spin. The message will stay on for 60 seconds. Four chimes will also be heard. Adjust your driving accordingly. When the ignition is turned off, this message will be displayed again for three seconds to remind you that your traction control system is not working properly. Be sure to have your vehicle serviced right away.
3-43
Battery Warning Message
When the vehicle is started this message will be displayed for three seconds.
Hot Coolant Temperature Warning Message
If the message is displayed when the engine is running, you may have a problem with your charging system. If there is a problem with the charging system, four chimes will sound when the message comes on. The battery display will also stay on while the key is in ON until the engine is started. If the message stays on after starting the engine it could indicate a problem with the generator drive belt, or some other charging system problem. Have it checked right away. Driving with this message on could drain your battery. If you must drive a short distance with this message displayed, it helps to turn off all your accessories.
United States
Canada
This message is displayed when the cooling system temperature gets hot. A chime will sound continuously, also. Check the coolant temperature gage and the coolant level. See Engine Coolant on page 5-29, Engine Coolant Temperature Gage on page 3-36 and Engine Overheating on page 5-32 for further information.
3-44
Low Oil Pressure Message
Low Engine Oil Level Message
United States
Canada
United States
Canada
This message is displayed when the engine oil pressure is low. A chime will sound continuously, also. See Engine Oil Pressure Gage on page 3-40.
Your vehicle may be equipped with a LOW ENG OIL LEVEL message. This message is displayed for 60 seconds at the start of each ignition cycle when the engine oil level is low. Four chimes will also sound. When the ignition is turned off, this message will be displayed again for three seconds to remind you that your engine oil level is low. Be sure to have your vehicle serviced right away. See Engine Oil on page 5-18 on how to check the oil level and for what type of oil to add.
3-45
Change Engine Oil Message
Low Tire Message
United States
Canada
United States
Canada
When this message comes on, it means that service is required for your vehicle. It will appear for 60 seconds. See Scheduled Maintenance on page 6-4 and Engine Oil on page 5-18 for more information. Once the engine oil has been changed, the CHANGE ENGINE OIL message must be reset. Until it is reset, this message will be displayed for 60 seconds each time you start the engine. For more information on resetting the system, see “How to Reset the Change Engine Oil Message” under Engine Oil on page 5-18.
Your vehicle may be equipped with the tire pressure system which monitors the inflation pressure of the tires. After the system has “learned” the tire pressure with properly inflated tires, the LOW TIRE PRESSURE message will be displayed and four warning chimes will sound if the tire pressure in one tire becomes 12 psi (83 kPa) lower than the other three tires. When you have checked the tire pressures, be sure to reset the tire inflation monitor. See “Tire Pressure Monitor System” under Tires on page 5-59.
3-46
Door Ajar Warning Message
Trunk Ajar Warning Message
United States
Canada
United States
Canada
This message will appear if one of the doors is not completely closed and the ignition is in ON. If you are in a forward or reverse gear position you will also hear four chimes.
This message will appear if the trunk is not completely closed and the ignition is in ON. If you are in a forward or reverse gear position you will also hear four chimes.
3-47
Security Message
Low Washer Fluid Warning Message
United States
Canada
United States
Canada
This message is displayed to monitor the Passlock® system. If the security message is displayed continuously while driving and stays on, there may be a problem with the Passlock® system. Your vehicle will not be protected by Passlock® and you should see your dealer for service. See Passlock® on page 2-15 for more information.
This message is displayed when the vehicle is low on windshield washer fluid. The message is only displayed for 60 seconds at the start of each ignition cycle. For more information see Windshield Washer Fluid on page 5-43. When the ignition is turned off, this message will be displayed again for three seconds to remind you that your washer fluid is low. Be sure to refill the washer fluid tank right away.
3-48
Low Fuel Warning Message
Low Brake Fluid Warning Message
United States
Canada
United States
Canada
This message is displayed when your vehicle is low on fuel. Four chimes will also sound. Refer to the fuel gage for a better indication of the amount of fuel remaining in the fuel tank.
This message will be displayed when your vehicle has a brake problem. The brake system warning light will also be illuminated. If this message appears, the brakes aren’t working properly. You should have your vehicle serviced immediately. See Brake System Warning Light on