1996 Chevrolet Monte Carlo Owners Manual

5-28

9. Tighten the wheel nuts firmly in a crisscross sequence as shown.

8. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely.

Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to 100 lb-ft (140 Nom).

Storing the Flat Tire and Tools

I ' A CAUTI(

Storing a jack, a tire or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

After you've put the compact spare tire on your vehicle you'll need to store the flat tire in your trunk. Use the following procedure to secure the flat tire in the trunk. Put the flat tire in the trunk so the side that faces out when it is on the vehicle is facing down. The full-size tire will not fit down into the well. Place it so the front is in the well and the rear is out of the well.

NOTICE:

Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification.

10. Don't try to put a wheel cover on your compact spare

tire, It won't fit. Store the wheel cover in the trunk until you have the flat tire repaired or replaced.

I NOTICE:

Wheel covers won't fit on your compact spare. If you try to put a wheel cover on your compact spare, you could damage the cover or the spare.

5-30

Put the bolt through one of the wheel nut holes, install the retainer over the bolt, then install the wing nut. Put the spacer and nut next to the tire in the well. Store the cover as far forward as possible. The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can. See “Compact Spare” in the Index. See the storage instructions label to replace your compact spare into your trunk properly. When you install the wheel cover on the full-size tire, tighten the nut caps to 5 Ib-ft (7 Nsm).

Storin

thc $pare Tire and Tools

~A CAUTION:

Storing a jack, a tire or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

Nut Cover Wing Nut Spacer Tire Wrench Nut Retainer Jack Bolt

5-32

qare

NOTICE:

Although the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inflated. The compact spare is made to perform well at posted speed limits for distances up to 3,000 miles (5 000 km), so you can finish your trip and have your full-size tire repaired or replaced where you want. Of course, it’s best to replace your spare with a full-size tire as soon as you can. Your spare will last longer and be in good shape in case you need it again.

When the compact spare is installed, don’t take your vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails. That can damage the tire and wheel, and maybe other parts of your vehicle.

Don’t use your compact spare on other vehicles. And don’t mix your compact spare tire or wheel with other wheels or tires’. They won’t fit. Keep your spare tire and its wheel together.

NOTICE:

Tire chains won’t fit your compact spare. Using them can damage your vehicle and can damage the chains too. Don’t use tire chains on your compact spare.

If You’re Stuck: In Sand, Mud, Ice or Snow What you don’t want to do when your vehicle is stuck is to spin your wheels too fast. The method known as “rocking” can help you get out when you’re stuck, but you must use caution.

If you let your tires spin at high speed, they can explode, and you or others could be injured. And, the transaxle or other parts of the vehicle can overheat. That could cause an engine compartment fire or other damage. When you’re stuck, spin the wheels as little as possible. Don’t spin the wheels above 35 mph (55 km/h) as shown on the speedometer.

I NOTICE:

Spinning your wheels can destroy parts of your vehicle as well as the tires. If you spin the wheels too fast while shifting your transaxle back and forth, you can destroy your transaxle.

For information about using tire chains on your vehicle, see “Tire Chains” in the Index. Rocking Your Vehicle to Get it Out First, turn your steering wheel left and right. That will clear the area around your front wheels. Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little as possible. Release the accelerator pedal while you shift, and press lightly on the accelerator pedal when the transaxle is in gear. If that doesn’t get you out after a few tries, you may need to be towed out. If you do need to be towed out, see “Towing Your Vehicle” in the Index.

5-34

NOTES

5-35

NOTES

5-36

Section 6 Service and Appearance Care

There is also technical information

Here you will find information about the care of your Chevrolet. This, section begins with service and fuel information, and then it shows how to check ,important fluid and lubricant levels. about your vehicle, and a p‘art devoted to its appearance care. Service Your Chevrolet dealer knows your vehicle best and wants you to be happy with it. We hope you’ll go to your dealer for all your service needs. You’ll get genuine GM parts and GM-trained and supported service people. We hope you’ll want to keep your GM vehicle all GM. Genuine GM parts have one of these marks:

Doing Your Own Service Work If you want to do some of your own service work, you’ll want to get the proper Chevrolet Service Manual. It tells you much more about how to service your Chevrolet than this manual can. To order the proper service manual, see “Service and Owner Publications” in the Index. Your vehicle has an air bag system. Before attempting to do your own service work, see “Servicing Your Air Bag-Equipped Chevrolet” in the Index. You should keep a record with all parts receipts and list the mileage and the date of any service work you perform. See “Maintenance Record” in the Index.

6-1

You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. 0 Be sure you have sufficient knowledge,

experience, and the proper replacement parts and tools before you attempt any vehicle maintenance task. Be sure to use the proper nuts, bolts and other fasteners. “English” and “metric” fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt.

Fuel Use regular unleaded gasoline rated at 87 octane or higher. At a.minimum, it should meet specificatiom.ASTM D4814 in the United States and CGSB 3.5-M93 in Canada. Improved gasoline specifications have been developed by the American Automobile Manufacturers Association (AAMA) for better vehicle performance and engine protection. Gasolines meting the AAMA specification 6-2

~~~

~~~

could provide improved driveability and emission control system protection compared to other gasolines. Be sure the posted octane is at least 87. If the octane is less than 87, you may get a heavy knocking noise when you drive. If it’s bad enough, it can damage your engine. If you’re using fuel rated at 87 octane or higher and you still hear heavy knocking, your engine needs service. But don’t worry if you hear a little pinging noise when you’re accelerating or driving up a hill. That’s normal, and you don’t have to buy a higher octane fuel to get rid of pinging. It’s the heavy, constant knock that means you have a problem. If your vehicle is certified to meet California Emission Standards (indicated on the underhood tune-up label), it is designed to operate on fuels that meet California specifications. If such fuels are not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance may be affected. The malfunction indicator lamp on your instrument panel may turn on and/or your vehicle may fail a smog-check test. If this occurs, return to your authorized Chevrolet dealer for diagnosis to determine the cause of failure. In the event it is determined that the cause of the condition is the type of fuels used, repairs may not be covered by your warranty.

In Canada, some gasolines contain an octane-enhancing additive called MMT. If you use such fuels, your emission control system performance may deteriorate and the malfunction indicator lamp on your instrument panel may turn on. If this happens, return to your authorized Chevrolet dealer for service. To provide cleaner air, all gasolines are now required to contain additives that will help prevent deposits from forming in your engine and fuel system, allowing your emission control system to function properly. Therefore, you should not have to add anything to the fuel. In addition, gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines may be available in your area to help clean the air. General Motors recommends that you use these gasolines if they comply with the specifications described earlier.

NOTICE:

Your vehicle was not designed for fuel that contains methanol. Don’t use it. It can corrode metal parts in your fuel system and also damage plastic and rubber parts. That damage wouldn’t be covered under your warranty.

Fuels in Foreign ‘loun If you plan on driving in another country outside the United States or Canada, the proper fuel may be hard to find. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel wouldn’t be covered by your warranty. To check on fuel availability, ask an auto club, or contact a major oil company that does business in the country where you’ll be driving. You can also write us at the following address for advice. Just tell us where you’re going and give your Vehicle Identification Number (VIN).

General Motors Overseas Distribution Corporation, North American Export Sales (NAES) 1908 Colonel Sam Drive Oshawa, Ontario LlH 8P7

6-3

Filling Your Tank

The cap is behind a hinged door on the left side of your vehicle..

While refueling; hang tbe cap inside the fuel door.

To take off the cap, turn it slowly to the left (counterclockwise).

: Gasoline vapor is highly flammable. It burns violently, and that can cause very bad injuries. Don’t smoke if yousre near gasoline or reheling your veh;ieIe. Keep sparks, flames, and smoking materials away from gasoline.

6-4

If you get gasoline on yourself and then something ignites it, you could be badly burned. Gasoline can spray out on you if you open the fuel filler cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel filler cap slowly and wait for any “hiss” noise to stop. Then unscrew the cap all the way.

Be careful not to spill gasoline. Clean gasoline from painted surfaces as soon as possible. See “Cleaning the Outside of Your Chevrolet” in the Index.

When you put the cap back on, turn it to the right until you hear at least three clicks. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See “Malfunction Indicator Lamp” in the Index.

NOTICE:

If you need a new cap, be sure to get the right type. Your dealer can get one for you. If you get the wrong type, it may not fit or have proper venting, and your fuel tank and emissions system might be damaged.

6-5

Checking Things Under the Hood

Hood Release

To open the'hood, first pull the handle inside the vehicle.

start up and An' electric fan under the hood'can' injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan.

I Things that burn can get on hot engine parts and

start a fire. These include liquids like gasoline, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that will burn onto a hot engine.

6-6 -

Then go to the front of the vehicle and release the secondary hood release. Lift the hood.

When you open the hood on the 3.1 L L82 (Code M) engine, you’ll see:

A. Engine Coolant Reservoir B. Radiator Fill Cap C. Power Steering Fluid Reservoir D. Engine Oil Fill Cap E. Engine Oil Dipstick

E Automatic Transaxle Dipstick G. Brake Fluid Reservoir H. Air Cleaner I. Windshield Washer Fluid Reservoir J. Batte~y (located under Windshield Washer Reservoir)

!i

When you open the hood on the 3.4L LQ1 (Code X) engine, you’ll see:

A. Engine Coolant Reservoir B. Radiator Fill Cap C . Power Steering Fluid Reservoir D. Engine Oil Fill Cap E. Engine Oil Dipstick 6-8

E Automatic Transaxle Dipstick G . Brake Fluid Reservoir H. Air Cleaner I. Windshield Washer Fluid Reservoir J. Battery (located under Windshield Washer Reservoir)

II

Before closing the hood, be sure all the filler caps are on properly. Then just pull the hood down and close it firmly. Engine Oil

LOW OIL

If the LOW OIL light on the instrument panel comes on, it means you need to check your engine oil level right away. For more information, see “Low Oil Level Light” in the Index. You should check your engine oil level regularly; this is an added reminder.

It’s a good idea to check your engine oil after you get fuel. In order to get an accurate reading, the oil must be hot and the vehicle must be on level ground.

3.1 L L82 (Code M) Engine

The engine oil dipstick handle is the yellow loop near the front of the engine.

6-9

,

3.4L LQ1 (Code X) Engine

Turn off the engine and give the oil 20 minutes to drain back into the oil pan. If you don’t, the oil dipstick might not show the actual level.

Checking Engine Oil Pull out the,dipstick and clean it with a paper towel or cloth, then push it back in all the way, Remove it again, keeping the tip down, and check the level. When to Add Oil If the oil is at or below the upper mark, then you’ll need to add some oil. But you must use the right kind. This part explains what kind of oil to use. For crankcase capacity, see “Capacities and Specifications” in the Index.

NOTICE:

Don’t add too much oil. If your engine’has SO much oil that the oil level gets above the cross-hatched area that shows the proper operating range, your engine could be damaged.

6-10

3.1 L L82 (Code M) Engine

3.4L LQ 1 (Code X) Engine

Just fill it enough to put the level somewhere in the proper operating range. Push the dipstick all the way back in when you’re through.

: Kind of Oil to

Oils recommended for your vehicle can be identified by looking for the “Starburst” symbol. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Do not use any oil which does not carry this Starburst symbol.

If you change your own oil, i be sure you use oil that has the Starburst symbol on the front of the oil container.

If you have your oil changed for you, be sure the oil put into your engine is American Petroleum Institute certified for gasoline engines. You should also use the proper viscosity oil for your vehicle, as shown in the following chart:

6-11

As shown in the chart, unless you have the 3.4L engine, SAE 5W-30 is best for your vehicle. However, you can use SAE 1OW-30 if it’s going to be 0°F (-18°C) or above. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils, such as SAE 20W-50.

RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS

~~~

FOR BEST FUEL ECONOMY AND COLD STARTING, SELECT THE LOWEST SAE VISCOSITY GRADE OIL FOR THE EXPECTED TEMPERATURE RANGE.

HOT

WEATHER “F “C

LOOK

FOR THIS SYMBOL

k 100-

. + 38

+ 80 -

- + 27

+ 60 -

- + 16

+ 40 -

- + 4

+ 20.

- - 7

- - 1 8

0 - i

COLD

WEATHER

SAE 1OW-30

SAE gW-30 PREFERRED

DO NOT USE SAE 2OW-50 OR ANY OTHER GRADE OIL NOT RECOMMENDED

RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS

FOR BEST FUEL ECONOMY AND COLD STARTING, SELECT ME LOWEST SAE VISCOSITY GRADE OIL FOR THE EXPECTED TEMPERATURE RANGE.

-~

-~

MOT

WEATHER

LOOK

FOR MIS SYMBOL

SAE

1OW-30

PREFERRED above 0°F (-18T)

SAE 5w-30

COLD

WEATHER

DO NOT USE SAE 2OW-50 OR ANY OTHER GRADE OIL NOT RECOMMENDED

As shown in the chart, if you have the 3.4L engine, SAE IOW-30 is best for your vehicle. However, you can use SAE 5W-30 if it’s going to be colder than 60°F ( 16°C) before your next oil change. When it’s very cold, you should use SAE 5W-30. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils, such as SAE 20W-50.

I NOTICE:

Use only engine oil with the American Petroleum Institute Certified For Gasoline Engines “Starburst” symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty.

GM Goodwrench@ oil meets all the requirements for your vehicle. l-7 ngin - Don’t add anything to your oil. Your Chevrolet dealer is ready to advise if you think something should be added.

6-13

What to Do with Used Oil Did you know that used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer? Don’t let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly throw away clothing or rags containing used engine oil. (See the manufacturer’s warnings about the use and disposal of oil products.) Used oil can be a real threat to the environment. If you change your own oil, be sure to drain all free-flowing oil from the filter before disposal. Don’t ever dispose of oil by putting it in the trash, pouring it on the ground, into sewers, or into streams or bodies of water. Instead, recycle it by taking it to a place that collects used oil. If you have a problem properly disposing of your used oil, ask your dealer, a service station or a local recycling center for help.

When to Change Engine Oil See if any one of these is true for you:

Most trips are less than 5 to 10 miles (8 to 16 km). This is particularly important when outside temperatures are below freezing. Most trips include extensive idling (such as frequent driving in stop-and-go traffic). Most trips are through dusty areas. You frequently tow a trailer or use a carrier on top of your vehicle. The vehicle is used for delivery service, police, taxi or other commercial application.

Driving under these conditions causes engine oil to break down sooner. If any one of these is true for your vehicle, then you need to change your oil and filter every 3,000 miles (5 000 km) or 3 months -- whichever occurs first. If none of them is true, change the oil and filter every 7,500 miles (12 500 km) or 12 months -- whichever occurs first. Driving a vehicle with a fully warmed engine under highway conditions causes engine oil to break down slower.

6-14

Air Cleaner

To check or replace the air filter, remove the four screws and pull off the cover.

Pull out the filter. Be sure to install the air filter and install the cover tightly when you are finished. Refer to the Maintenance Schedule to determine when to replace the air filter. See “Scheduled Maintenance Services” in the Index.

6-15

- ,A CAUTION:

Operating the engine with the air cleaner off can cause you or others to be burned. The air cleaner not only cleans the air, it stops flame if the engine backfires. If it isn’t there, and the engine backfires, you could be burned. Don’t drive with it off, and be careful working on the engine with the air cleaner off.

NOTICE:

If the air cleaner is off, a backfire can cause a damaging engine fire. And, dirt can easily get into your engine, which will damage it. Always have the air cleaner in place when you’re driving.

Automatic Transaxle Fluid When to Check and Change A good time to check your automatic transaxle fluid level is when the engine oil is changed. Change both the fluid and filter every 50,000 miles (83 000 km) if the vehicle is mainly driven under one or more of these conditions:

In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. In hilly or mountainous terrain.

0 When doing frequent trailer towing. 0 Uses such as found in taxi, police or delivery service. If you do not use your vehicle under any of these conditions, the fluid and filter do not require changing. See “Scheduled Maintenance Services’’ in the Index.

6-16

How to Check Because this operation can be a little difficult, you may choose to have this done at your Chevrolet dealer Service Department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick.

NOTICE:

Too much or too little fluid can damage your transaxle. Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire. Be sure to get an accurate reading if you check your transaxle fluid.

Wait at least 30 minutes before checking the transaxle fluid level if you have been driving: 0 When outside temperatures are above 90°F (32°C).

At high speed for quite a while.

0 11-1 heavy traffic -- especially i n hot weather

While pulling a trailer.

To get the right reading, the fluid should be at normal operating temperature, which is 180°F to 200°F (82°C to 93°C). Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above 50°F (10°C). If it's colder than 50°F (lO"C), you may have to drive longer.

Checking the Fluid Level

Park your vehicle on a level place. Keep the engine running. With the parking brake applied, place the shift lever in PARK (P). With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, position the shift lever in PARK (P). Let the engine run at idle for three to five minutes.

6-17

Then, without shutting off the engme, follow these steps:

3.1 L L82 (Code M) Engine

3.4L LQl (Code X) Engine

1, The transaxle fluid dipstick handle is the red loop

near the back of the engine. Pull out the dipstick and wipe it with a clean rag or paper towel.

2. Push it back in all the way, wait three seconds and

then pull it back out again.

3.1 L L82 (Code M) Engine 3.4L

LQI. (Code X) Engine

3. Check both sides of the dipstick, and read the

lower level. The fluid level must be in the cross-hatched area.

4. If the fluid level is in the acceptable range, push the

dipstick back in all the way.

4-18

How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transaxle fluid to use. See “Recommended Fluids and Lubricants” in the Index. If the fluid level is low, add only enough of the proper fluid to bring the level into the cross-hatched area on the dipstick. 1. Pull out the dipstick. 2. Using a long-neck funnel, add enough fluid at the

dipstick hole to bring it to the proper level. It doesn’t take much fluid, generally less than a pint (OSL). Don ’t overfill. We recommend you use only fluid labeled DEXRON@-111, because fluid with that label is made especially for your automatic transaxle. Damage caused by fluid other than DEXRON@-I11 is not covered by your new vehicle warranty. 0 After adding fluid, recheck the fluid level as

described under “How to Check.”

0 When the correct fluid level is obtained, push the

dipstick back in all the way.

Engine Coolant The cooling system in your vehicle is filled with new DEX-COOL TM (orange-colored, silicate-free) engine coolant. This coolant is designed to remain in your vehicle for 5 years or 100,000 miles ( 166 000 km), whichever occurs first. The following explains your cooling system and how to add coolant when it is low. If you have a problem with engine overheating or if you need to add coolant to your radiator, see “Engine Overheating” in the Index. A 50/50 mixture of water and the proper coolant for your Chevrolet will: 0 Give freezing protection down to -34°F (-37°C). 0 Give boiling protection up to 265°F (129°C).

Protect against rust and corrosion.

0 Help keep the proper engine temperature. 0 Let the warning lights and gages work as they

should.

NOTICE:

When adding coolant it is important that you use DEX-COOL TM (orange-colored, silicate-free) coolant meeting GM Specification 6277M. If silicated coolant is added to the system, premature engine, heater core or radiator coolant will require change sooner -- at corrosion may result. In addition, the engine 30,000 miles (50 000 km) or 24 months whichever occurs first.

What to Use Use a mixture of one-half clean water (preferably distilled) and one-half DEX-COOL TM (orange-colored, silicate-free) antifreeze that meets GM Specification 6277M, which won’t damage aluminum parts. Use

GM Engine Coolant Supplement (sealer) (GM Part No. 3634621) with any complete coolant change. If you use this mixture, you don’t need to add anything else.

Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid like alcohol, can boil before the proper coolant mix will. Your vehicle’s coolant warning system is set for the proper coolant mix. With plain water or the wrong mix, your engine could get too hot but you wouldn’t get the overheat warning. Your engine could catch fire and you or others could be burned. Use a 50/50 mix of clean water and DEX-COOL TM (orange-colored, silicate-free) antifreeze.

NOTICE:

If you use an improper coolant mix, your engine could overheat and be badly damaged. The repair cost wouldn’t be covered by your warranty. Too much water in the mix can freeze and crack the engine, radiator, heater core and other parts.

If you have to add coolant more than four times a year, have your dealer check your cooling system.

I NOTICE:

Checking Coolant

r -

If you use the proper coolant, you don’t have to add extra inhibitors or additives which claim to improve the system. These can be harmful.

When your engine is cold, the coolant level should be at the COLD mark or a little higher. When .your engine is warm, the level should be up to the HOT mark or a little higher.

6-21

If this light comes on, it means you’re low on engine coolant.

LOW

COOLANT

Adding Coolant If you need more coolant, add the proper mix at the coolant recovery tank. If the coolant recovery tank is completely empty, add coolant to the radiator. (See “Engine Overheating” in the Index.)

Thrning the radiator pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. With the coolant recovery tank, you will almost Never turn the radiator pressure cap -- even a never have to add coolant at the radiator. little -- when the engine and radiator are hot.

Add coolant mix at the recovery tank, but be careful not to spill it.

A CAUTION:

You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Don’t spill coolant on a hot engine.

6-22

Radiator Pressure Cap

Power Steering Fluid

NOTICE:

Your radiator cap is a 15 psi (105 kPa) pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating. Be sure the arrows on the cap line up with the overflow tube on the radiator filler neck.

When you replace your radiator pressure cap, an AC@ cap is recommended. Thermostat Engine coolant temperature is controlled by a thermostat in the engine coolant system. The thermostat stops the flow of coolant through the radiator until the coolant reaches a preset temperature. When you replace your thermostat, an AC@ thermostat is recommended.

3.4L LQI (Code X) Engine

3.1L L82 (Code M) Engine When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss-in this system could indicate a problem. Have the system inspected and repaired.

6-23

How To Check Power Steering Fluid When the engine compartment is cool, unscrew the cap and wipe the dipstick with a clean rag. Replace the cap and completely tighten it. Then remove the cap, again and look at the fluid level on the dipstick.

When the engine compartment is hot, the

Windshield Washer Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Adding Washer Fluid

What to Use Refer to the Maintenance Schedule to determine what kind of fluid to use. See “Recommended Fluids and Lubricants” in the Index. Always use the proper fluid. Failure to use the proper fluid can cause leaks and damage hoses and seals.

Open the cap labeled WASHER FLUID OmY. Add washer fluid until the tank is full.

0

When using concentrated washer fluid, follow the manufacturer’s instructions for adding water. Don’t mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water doesn’t clean as well as washer fluid. Fill your washer fluid tank only 3/4 full when it’s very cold. This allows for expansion, which could damage the tank if it is completely full. Don’t use radiator antifreeze in your windshield washer. It can damage your washer system and paint.

Brakes Brake Fluid

Your brake master cylinder reservoir is here. It is filled with DOT-3 brake fluid.

When your brake fluid falls to a low level, your brake warning light will come on. See “Brake System Warning Light” in the Index.

What to Add When you do need brake fluid, use only DOT-3 brake fluid -- such as Delco Supreme 11 No. 1052535). Use new brake fluid from a sealed container only, and always clean the brake fluid reservoir cap before removing it.

(GM Part

With the wrong kind of fluid in your brake system, your brakes may not work well, or they may not even work at all. This could cause a crash. Always use the proper brake fluid.

There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lining wear. When new linings are put in, the fluid level goes back up. The other reason is that fluid is leaking out of the brake system. If it is, you should have your brake system fixed, since a leak means that sooner or later your brakes won’t work well, or won’t work at all. So, it isn’t a good idea to “top off’ your brake fluid. Adding brake fluid won’t correct a leak. If you add fluid when your linings are worn, then you’ll have too much fluid when you get new brake linings. You should add (or remove) brake fluid, as necessary, only when work is done on the brake hydraulic system.

If you have too much brake fluid, it can spill on the engine. The fluid will burn if the engine is hot enough. You or others could be burned, and your vehicle could be damaged. Add brake fluid only when work is done on the brake hydraulic system.

6-26

NOTICE:

Using the wrong fluid can badly damage brake system parts. For example, just a few drops of mineral-based oil, such as engine oil, in your brake system can damage brake system parts so badly that they’ll have to be replaced. Don’t let sonleone put in the wrong kind of fluid. If you spill brake fluid on your vehicle’s painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on your vehicle. If you do, wash it off immediately. See “Appearance Care” in the Index.

Brake Wear Your Chevrolet has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal firmly).

The brake wear warning sound means that sooner or later your brakes won’t work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced.

6-27

I NOTICE:

Continuing to drive with worn-out brake pads could result in costly brake repair.

Some driving conditions or climates may cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with your brakes. Free movement of brake calipers and properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake calipers for movement, brake pads for wear, and evenly torque wheel nuts in the proper sequence to GM specifications. Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake Adjustment Every time you apply the brakes, with or without the vehicle moving, your brakes adjust for wear. 6-28

Replacing Brake System Parts The braking system on a modern vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Vehicles we design and test have top-quality GM brake parts in them, as your Chevrolet does when it is new. When you replace parts of your braking system -- for example, when your brake linings wear down and you have to have new ones put in -- be sure you get new genuine GM replacement parts. If you don’t, your brakes may no longer work properly. For example, if someone puts in brake linings that are wrong for your vehicle, the balance between your front and rear brakes can change -- for the worse. The braking performance you’ve come to expect can change in many other ways if someone puts in the wrong replacement brake parts. Battery Every new Chevrolet has a Delco Freedom@ battery. You never have to add water to one of these. When it’s time for a new battery, we recommend a Delco Freedom@ battery. Get one that has the replacement number shown on the original battery’s label.

Vehicle Storage If you’re not going to drive your vehicle for 25 days or more, take off the black, negative (-) cable from the battery. This will help keep your battery from running down.

’

A CAUTION:

Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you aren’t careful. See “Jump Starting” in the Index for tips on working around a battery without getting hurt.

Contact your dealer to learn how to prepare your vehicle for longer storage periods. Also, for your audio system, see “Theft-Deterrent Feature” in the Index.

Bulb Replacement In this section you’ll find directions for changing the bulbs in some of the lamps on your Chevrolet. See “Replacement Bulbs” in the Index to find the type of bulb you should use. Halogen Bulbs

Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.

Headlamps 1. Open the hood. 2. Press and turn the base a quarter-turn

(counterclockwise for the driver’s side; clockwise for the passenger’s side) and remove it from the retaining ring by gently pulling it back and away from the headlamp.

6-29

Front Park and Turn Signal Lamp

3.

4. 5.

6.

Remove the electrical connector from the bulb by raising the lock tab and pulling the connector away from the bulb's base. Install the electrical connector to the bulb. Install the new bulb by inserting the smallest tab on the bulb base into the matching notch in the retaining ring. Turn the bulb a quarter-turn clockwise until it stops. Close the hood.

1. Open the hood. There is one flap on each side of

the radiator.

2. Open the flap by lifting the snap screw.

3. Position the radiator air side baffle aside and remove

the two nuts (pliers may be required).

Front and Rear Sidemarker Front and Rear Sidemarker

1. Remove the screw from 1. Remove the screw from

the sidemarker lens. the sidemarker lens.

4. Slide the headlamp assembly outboard and gently pull

the inside of the assembly away from the vehicle.

5. Push the tab on the bulb socket and turn itj

counterclockwise. Pull the socket out of the assembly.

6. Remove the bulb from the socket by pulling it out.

Do not twist the bulb.

7. Push in the new bulb. 8. Reverse Steps 1-4 to replace the assembly.

6-32

Center High-Mounted Stoplamp (Shelf-Mounted) To reach the center high-mounted stoplamp, you must go through the trunk.

2. 3.

4. 5. 6. 7.

the body.

Pull the sidemarker lens away from Turn the socket counterclockwise until it stops. Then pull the socket and bulb from the assembly. Pull the bulb out of the socket. Do not twist the bulb. Plug the new bulb in the socket. Replace the bulb and socket. Replace the assembly in the vehicle. Replace the screw.

1. Open the trunk lid. Locate the stoplamp behind the

rear seats, in front of the tmnk hinges.

2.

3.

4.

Turn the socket counterclockwise until it stops and pull the bulb and socket out of the assembly. Push in the bulb, turn it counterclockwise and pull it out of the socket. Push the new bulb into the socket and turn it clockwise. Replace the bulb and socket in the assembly.

5. Center High-Moun.kd. Stoplamp (Spoiler-Mounted) 1. Remove the two screws from the stoplamp assembly. 2. Pull the assembly forward out of the spoiler. 3. Remove the three screws from the back of the

stoplamp assembly.

TaiVStop/Turn Signal Lamp 1. Open the trunk. Remove the convenience net if you have one. Unhook the net from the upper wing nut.

2.

3.

Remove the upper (convenience net) wing nut, if equipped. Pull the carpet away from the rear of the vehicle.

4. Pull the lamp strip out of the stoplamp assembly. 5. Remove the bulb. 6. Install the new bulb and reverse Steps 1-4.

4. Unscrew the two remaining wing nuts. 5. Pull the assembly from the body carefully.

6-34

6. To remove a socket, press the tab, turn the socket counterclockwise and pull it out.

7. Pull the bulb out. Do not

twist it.

Back-up Lamp 1. Open the trunk. The back-up lamp bulbs are in the

rear of the trunk lid.

2. Press the tab on the

socket, turn the socket counterclockwise and pull it out.

8. Push the new bulb into the socket. 9. Replace the socket in the assembly. 10. Tighten the socket (both kinds) by turning

it clockwise.

11. Install the assembly and the two lower wing nuts. 12. Replace the carpeting. 13. Replace the upper (convenience net) wing nut,

if equipped.

14. Replace the convenience net, if equipped.

3. To remove the bulb, pull it out of the socket. Do not

twist the bulb.

4. Push the new bulb into the socket. 5. Reverse Steps 1-3 to replace the socket.

6-35

Tires We don’t make tires. Your new Chevrolet comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your Chevrolet Warranty booklet for details.

Poorly maintained and improperly used tires are dangerous. 0 Overloading your tires can cause

overheating as a result of too much friction. You could have an air-out and a serious accident. See “Loading Your Vehicle” in the Index.

CAUTION: (Continued)

Windshield Wiper Blade Replacement 1. Pull the windshield wiper arm away from the windshield.

2. Lift the release clip with a screwdriver and pull the

blade off the wiper arm.

3. Push the new wiper blade securely onto the wiper arm. For wiper blade replacement length and type, see ”Capacities and Specifications” in the Index.

6-36

0

Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold. Overinflated tires are more likely to be cut, punctured or broken by a sudden impact -- such as when you hit a pothole. Keep tires at the recommended pressure. Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them.

Inflation - Tire Pressure The Tire-Loading Information label which is on the {inside of the trunk lid shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than a mile.

NOTICE:

Don’t let anyone tell you that underinflation or overinflation is all right. It’s not. If your tires don’t have enough air (underinflation), you can get the following:

Too much flexing Too much heat Tire overloading Bad wear

0 Bad handling

Bad fuel economy.

If your tires have too much air (overinflation), you can get the following:

Unusual wear Bad handling

0 Rough ride 0 Needless damage from road hazards.

6-37 ,

When to Check Check your tires once a month or more. Don’t forget your compact spare tire. It should be at 60 psi (420 kPa).

How to Check Use a good quality pocket-type gage to check tire pressure. You can’t tell if your tires are properly inflated simply by looking at them. Radial tires may look properly ‘inflated even when they’re underinflated. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture. Tire Inspection and Rotation Tires should be inspected every 6,000 to 8,000 miles (10 000 to 13 000 km) for any signs of unusual wear. If unusual wear is present, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See “When It’s Time for New Tires’’ and “Wheel Replacement” later in this section for more information.

u-30

The purpose of regular rotation is to achieve more uniform wear for all tires on the vehicle. The k rotation is tlle most important. See “Scheduled Maintenance Services” in the Index for scheduled rotation intervals. Whcn rotating your tires, always use the correct rotation pattern shown here. Don’t include the compact spare tire in your tire rotation.

I1

After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire-Loading Information label. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” in the

Index.

When It’s Time for New Tires

One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining.

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off. (See ‘(Changing a Flat Tire? in the Index.)

You need a new tire if any of the following statements are true:

You can see the indicators at three or more places around the tire. You can see cord or fabric showing through the tire’s rubber. The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric.

0 The tire has a bump, bulge or split.

The tire has a puncture, cut or other damage that can’t be repaired well because of the size or location of the damage.

6-39

Buying New Tires To find out what kind and size of tires you need, look at the Tire-Loading Information label. The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification (TPC Spec) number on each ti.re’s sidewall. When you get new tires, get ones with that same TPC Spec number. That way your vehicle will continue to have tires that are designed to give proper endurance, handling, speed rating, traction, ride and other things during normal service on your vehicle. If your tires have an all-season tread design, the TPC number will be followed by an “MS” (for mud and snow). If you ever replace your tires with those not having a TPC SDec number. make sure thev are the same size, load range, speed rating and construction type (bias, bias-belted or radial) as your original tires.

- - I -

~~

Mixing tires could cause you to lose control while driving. If you mix tires of different sizes or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle. Be sure to use the same size and type tires on all four wheels. It’s all right to drive with your compact spare, though. It was developed for use on your vehicle.

Uniform Tire Quality Grading The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, &action and temperature performance. (This applies only to vehicles sold in the United States.) The grades are molded on the sidewas of most passenger car tires. The Uniform Tire Quality Grading system does not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires.

While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to Federal safety requirements and additional General Motors Tire Performance Criteria‘(TPC) standards.

Warning: The traction grade assigned to this tire is based on braking (straightahead) traction tests and does not include cornering (turning) traction.

Temperature - A, B, C

Tread wear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half ( I 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. Traction - A, B, C The traction grades, from highest to lowest, are A, B, and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. In most cases, you will not need to have your wheels aligned again. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced. Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your Chevrolet dealer if any of these conditions exist. Your dealer will know the kind of wheel you need.

Each new wheel should have the same load carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your Chevrolet model.

CAUTION:

Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement.

6-42

NOTICE:

The wrong wheel can also cause problems with bearing life, brake cooling, speedometer/odometer calibration, headlamp aim, bumper height, vehicle ground clearance and tire or tire chain clearance to ,the body and chassis.

See “Changing a Flat Tire” in the Index for more information.

Used Replacement Wheels,

Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how many miles it’s been driven. It could fail suddenly and cause an accident. If you have to replace a wheel, use a new GM original equipment wheel.

Tire Chains

NOTICE:

If your Chevrolet has P22960Rl6 size tires, don’t use tire chains. They can damage your vehicle. If you have other tires, use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires. Install them on the front tires and tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop &d retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.

6-43

Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flame if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space. When you use anything from a container to clean your Chevrolet, be sure to follow the manufacturer’s warnings and instructions. And always open your doors or windows when you’re cleaning the inside. Never use these to clean your vehicle: 0 Gasoline Benzene 0 Naphtha

Carbon Tetrachloride Acetone

0 Paint Thinner 0 Turpentine 0 Lacquer Thinner 0 Nail Polish Remover They can all be hazardous -- some more than others -- and they can all damage your vehicle, too.

6-44

Don’t use any of these unless this manual says you can. In many uses, these will damage your vehicle: 0 Alcohol 0 Laundry Soap 0 Bleach 0 Reducing Agents Cleaning the Inside of Your Chevrolet Use a vacuum cleaner often to get rid of dust and loose dirt. Wipe vinyl or leather with a clean, damp cloth. Your Chevrolet dealer has two GM cleaners, a solvent-type spot lifter and a foam-type powdered cleaner. They will clean normal spots and stains very well. Do not use them on vinyl or leather. Here are some cleaning tips: 0 Always read the instructions on the cleaner label.

Clean up stains as soon as you can -- before they set. 0 Use a clean cloth or sponge, and change to a clean area often. A soft brush may be used if stains are stubborn.

0 Use solvent-type cleaners in a well-ventilated area

only. If you use them, don’t saturate the stained area. If a ring forms after spot cleaning, clean the entire area immediately or it will set.

0

Using Foam-Type Cleaner on Fabric

Vacuum and brush the area to remove any loose dirt. Always clean a whole trim panel or section. Mask surrounding trim along stitch or welt lines. Mix Multi-Purpose Powdered Cleaner following the directions on the container label. Use suds only and apply with a clean sponge. Don’t saturate the material. Don’t rub it roughly. As soon as you’ve cleaned the section, use a sponge to remove the suds. Rinse the section with a clean, wet sponge. Wipe off what’s left with a slightly damp paper towel or cloth. Then dry it immediately with a blow dryer. Wipe with a clean cloth.

Using Solvent-wpe Cleaner on Fabric First, see if you have to use solvent-type cleaner at all. Some spots and stains will clean off better with just water and mild soap.

If you need to use a solvent: 0 Gently scrape excess soil from the trim material with a clean, dull knife or scraper. Use very little cleaner, light pressure and clean cloths (preferably cheesecloth). Cleaning should start at the outside of the stain, “feathering” toward the center. Keep changing to a clean section of the cloth.

0 When you clean a stain from fabric, immediately dry the area with a blow dryer to help prevent a cleaning ring.

Fabric Protection Your Chevrolet has upholstery and carpet that has been treated with Scotchgard” Fabric Protector, a 3M product. It protects fabrics by repelling oil and water, which are the carriers of most stains. Even with this protection, you still need to clean your upholstery and carpet often to keep it looking new. Further information on cleaning is available by calling 1-800-433-3296 (in Minnesota, 1-800-642-6 167).

6-45

Special Cleaning Problems Greasy or Oily Stains Stains caused by grease, oil, butter, margarine, shoe polish, coffee with cream, chewing gum, cosmetic creams, vegetable oils, wax crayon, tar and asphalt can be removed as follows:

Carefully scrape off excess stain. Follow the solvent-type instructions described earlier. Shoe polish, wax crayon, tar and asphalt will stain if left on a vehicle's seat fabric. They should be removed as soon as possible. Be careful, because the cleaner will dissolve them and may cause them to spread.

Non-Greasy Stains Stains caused by catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, wine, vomit, urine and blood can be removed as follows: 0 Carefully scrape off excess stain, then sponge the

soiled area with cool water.

0 If a stain remains, follow the foam-type instructions

described earlier.

6-46

0 If an odor lingers after cleaning vomit or urine, treat the area with a watedbaking soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml) of lukewarm water. If needed, clean lightly with solvent-type cleaner.

Combination Stains Stains caused by candy, ice cream, mayonnaise, chili sauce and unknown stains can be removed as follows: 0 Carefully scrape off excess stain, then clean with

cool water and allow to dry.

0 If a stain remains, clean it with solvent-type cleaner. Cleaning Vinyl Use warm water and a clean cloth.

Rub with a clean, damp cloth to remove dirt. You may have to do it more than once.

0 Things like tar, asphalt and shoe polish will stain if

you don't get them off quickly. Use a clean cloth and a GM VinyVLeather Cleaner or equivalent product.

Cleaning Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap.

For stubborn stains, use a GM Vinylkeather Cleaner or equivalent product. Never use oils, varnishes, solvent-based or abrasive cleaners, furniture polish or shoe polish on leather. Soiled leather should be cleaned immediately. If dirt is allowed to work into the finish, it can harm the leather.

Cleaning the Top of the Instrument Panel Use only mild soap and water to clean the top surfxes of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Care of Safety Belts Keep belts clean and dry.

/;1 4UTION:

Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.

Glass Glass should be cleaned often. GM Glass Cleaner (GM Part No. 1050427) or a liquid household glass cleaner will remove normal tobacco smoke and dust films. Don’t use abrasive cleaners on glass, because they may cause scratches. Avoid placing decals on the inside rear window, since they may have to be scraped off later. If abrasive cleaners are used on the inside of the rear window, an electric defogger element may be damaged. Any temporary license should not be attached across the defogger grid.

Cleaning the Outside of Your Chevrolet The paint finish on your vehicle provides beauty, depth of color, gloss retention and durability. Washing Your Vehicle The best way to preserve your vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Don’t wash your vehicle in the direct rays of the sun. Don’t use strong soaps or chemical detergents. Use liquid hand, dish or car washing (mild detergent) soaps. Don’t use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or a 100% cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter your vehicle.

Cleaning the Outside of the Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with GM Windshield Cleaner, Bon-Ami PowderB (GM Part No. 1050011). The windshield is clean if beads do not form when you rinse it with water. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Wiper blades should be checked on a regular basis and replaced when worn. Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth at least every six months. During very cold, damp weather more frequent application may be required. (See “Recommended Fluids and Lubricants” in the Index.)

6-48

Finish Care Occasional waxing or mild polishing of your Chevrolet by hand may be necessary to remove residue from the paint finish. You can get GM-approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.) Your Chevrolet has a “basecoat/clearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish.

I NOTICE:

Machine compounding or aggressive polishing on a basecoatklearcoat paint finish may dull the finish or leave swirl marks.

Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc. can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If

necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your Chevrolet garaged or covered whenever possible. Aluminum Wheels (If So Equipped) Keep your wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. The surfwe of these wheels is similar to the painted surface of your vehicle. Don’t use strong soaps, chemicals, abrasive polishes, abrasive cleaners or abrasive cleaning brushes on them because you could damage the surface. Don’t take your vehicle through an automatic car wash that has silicon carbide tire cleaning brushes. These brushes can also damage the surface of these wheels.

Tires To clean your tires, use a stiff brush with a tire cleaner.

NOTICE:

When applying a tire dressing always take care to wipe off any overspray or splash from all painted surfaces on the body or wheels of the vehicle. Petroleum-based products may damage the paint finish.

Sheet Metal Damage If your vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to the parts repaired or replaced to restore corrosion protection. Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into a major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer or other service

6-50

outlets. Larger areas of finish damage can be corrected in your dealer’s body and paint shop. Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, accelerated corrosion (lust) can occur on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and other debris can collect. Dirt packed in closed areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this for you. Chemical Paint Spatting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fdl upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ringlet-shaped discolorations, and small irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, Chevrolet will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within I2 months or 12,000 miles (20 000 kin) of purchase, whichever occurs first.

Appearance Care Materia

s Chart

PART NUMBER

1050004 1050172 1050173 1050174 1050201 1050214 1050427 1050429 105 1398" 1051515 1052870 1052918** 1052929 1052930 12345002"" 12345725

SIZE

2.75 sq. ft.

16 oz. (0.473 L) 16 oz. (0.473 L) 16 oz. (0.473 L) 16 02. (0.473 L) 32 oz. (0.946 L) 23 oz. (0.680 L) 6 lbs. (2.72 kg) 8 02. (0.237 L) 32 02. (0.946 L) 16 oz. (0.473 L) 8 oz. (0.237 L) 16 oz. (0.473 L) 8 oz. (0.237 L) 16 oz. (0.473 L)

DESCRIPTION

Chamois

Tar and Road Oil Remover Chrome Cleaner and Polish White Sidewall Tife Cleaner Magic Mirror Cleaner Polish Vinyl and Leather Cleaner

Glass 'Cleaner

Multi-Purpose Powdered Cleaner

Spot Lifter Optikleen

Wash and Wax Concentrate

Armor All Protector

Wheel Cleaner

Capture Dry Spot Remover

USAGE

Shines vehicle without scratching

Also removes old waxes and polishes

Removes rust and corrosion Removes soil and black marks

Exterior cleaner and polish

Spot and stain removal

Cleans grease, grime and smoke film Cleans vinyl, cloth, tires and mats

For cloth

Windshield washer solvent and antifreeze

Exterior wash

Protects vinyl, leather and rubber

Spray on wheel cleaner Attracts and absorbs soils

Cleans vinyl, leather and rubber

Shines tires

I 12 oz. (0.354 L) I I See "Fluids and Lubricants" in the-Index.

See your General Motors Parts Department for these products.

Armor All Cleaner Silicone Tire Shine

* Not recommended for pigskin suede leather. **Not recommended for use'on instrument panel vinyl. I

6-51

''

Vehicle Identification umber (VIN)

This is the legal identifier for your Chevrolet. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration. Engine Identification The eighth character in your VIN is the engine code. This code will help you identify your engine, specifications, and replacement parts. Service Parts Identification Label You’ll find this label on your spare tire cover. It’s very helpful if you ever need to order parts. On this label is: 0 your VIN,

6-52

the model designation, paint information, and a list of all production options and special equipment.

Be sure that this label is not removed from the vehicle. Electrical System Add-on Electrical Equipment

I NOTICE:

Don’t add anything electrical to your Chevrolet unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.

Your vehicle has an air bag system. Before attempting to add anything electrical to your Chevrolet, see “Servicing Your Air Bag-Equipped Chevrolet” in the Index.

Headlamp Wiring The headlamp wiring is protected by a circuit breaker in the underhood electrical center. An electrical overload will cause the lamps to go on and off, or in some cases to remain off. If this happens, have your headlamp system checked right away. Windshield Wipers The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, have it fixed. Power Windows and Other Power Options Circuit breakers in the fuse panel protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed.

Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers, and fusible thermal links in the wiring itself. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating. --. Instrument Panel Fuse Block

[

- A

Circuit Breaker

Description Fuse Rating Description

Power Windows Power Seats

CIGAR LIGHTER -- Instrument Panel and Console Cigar Lighters DLRMDL

3.

6-54

Fuse

10

11 12

13

14

15

16

Rating Description HVAC #2 -- W A C Control Assembly, Solenoid Box H A Z A P FLASHER POWER ACCESSORY #2 -- Sunroof Control Unit I/P ELECTRONICS BATTERY FEED -- Chime Module, Electronic " Brake Control Module (EBCM), Theft-Deterrent Module, Radio STARTER RELAY ANTI-THEFT -- Theft-Deterrent Module ABS--Electronic Brake Control Module (EBCM), ABS Relay W A C BLOWER MOTOR -- Blower Motor Relay W A C #1 -- Air Temperature Valve Motor, Daytime Running Lamps Module @RL), HVAC Control Assembly, Multifunction Lever Cruise Control Switch REAR DEFOG -- HVAC Control Assembly Rear Window Defogger Switch

Fuse 30 TURN SIGNAL

Rating Description

-- Turn

32

3-8

39

Signal Flasher POWER LOCKS -- Door Lock Relay, Keyless Entry Receiver RADIO -- Radio, Steering Wheel Radio Switches I/P ELECTRONICS IGNITION FEED -- Headlamp Switch, Cruise Control Cut-Out Switch, Air Bag System, TCClBrake Switch, Instrument Cluster, Chime Module, Keyless Entry Receiver, Daytime Running

, Lamps Module (DRL)

Fuse 19