2016 Chevrolet Malibu Owners Manual

. The indicator moves a little while turning a corner or speeding up. . The gauge goes back to empty when the ignition is turned off.

Engine Coolant Temperature Gauge

Instruments and Controls

103

Safety Belt Reminders

Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.

This gauge shows the engine coolant temperature. If the indicator needle moves to the hot side of the gauge, the engine is too hot. If the vehicle has been operated under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible.

When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

104

Instruments and Controls

Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System 0 68.

When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on. The front passenger safety belt reminder light and chime may turn on if an object is put on the seat such as a briefcase, handbag,

grocery bag, laptop, or other electronic device. To turn off the reminder light and/or chime, remove the object from the seat or buckle the safety belt.

Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System 0 62.

The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.

{ Warning

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System 0 68. The overhead console has a passenger airbag status indicator.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Instruments and Controls

105

outboard passenger frontal airbag and knee airbag are allowed to inflate. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag and knee airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ Warning

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light 0 104 for more information, including important safety information.

Charging System Light

This light comes on briefly when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. The light should go out once the engine starts. If it stays on, or comes on while driving, there could be a problem with the charging system. This light could indicate that there are problems with a generator drive belt, or that there is an electrical problem. Have it checked right away. If the vehicle must be driven a short distance with the light on, turn off accessories, such as the radio and air conditioner.

United States

Canada

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol, to let you know the status of the front outboard passenger frontal airbag and knee airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the front

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

106

Instruments and Controls

Malfunction Indicator Lamp (Check Engine Light) This light is part of the vehicle’s emission control on-board diagnostic system. If this light is on while the engine is running, a malfunction has been detected and the vehicle may require service. The light should come on to show that it is working when the ignition is in ON/RUN with the engine not running for Key Access or in Service Only Mode for Keyless Access. See Ignition Positions (Keyless Access) 0 187 or Ignition Positions (Key Access) 0 189.

Malfunctions are often indicated by the system before any problem is noticeable. Being aware of the light and seeking service promptly when it comes on may prevent damage.

Caution

If the vehicle is driven continually with this light on, the emission control system may not work as well, the fuel economy may be lower, and the vehicle may not run smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.

Caution

Modifications to the engine, transmission, exhaust, intake, or fuel system, or the use of replacement tires that do not meet the original tire specifications, can cause this light to come on. This could lead to costly repairs not covered by the vehicle warranty. This could also affect the vehicle’s ability to pass an Emissions Inspection/ Maintenance test. See Accessories and Modifications 0 226.

If the light is flashing : A malfunction has been detected that could damage the emission control system and increase vehicle emissions. Diagnosis and service may be required. To help prevent damage, reduce vehicle speed and avoid hard accelerations and uphill grades. If towing a trailer, reduce the amount of cargo being hauled as soon as possible. If the light continues to flash, find a safe place to park. Turn the vehicle off and wait at least 10 seconds before restarting the engine. If the light is still flashing, follow the previous guidelines and see your dealer for service as soon as possible. If the light is on steady : A malfunction has been detected. Diagnosis and service may be required. Check the following: . A loose or missing fuel cap may cause the light to come on. See Filling the Tank 0 216. A few

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

driving trips with the cap properly installed may turn the light off.

. Poor fuel quality can cause

inefficient engine operation and poor driveability, which may go away once the engine is warmed up. If this occurs, change the fuel brand. It may require at least one full tank of the proper fuel to turn the light off. See Fuel 0 215.

If the light remains on, see your dealer. Emissions Inspection and Maintenance Programs If the vehicle requires an Emissions Inspection/Maintenance test, the test equipment will likely connect to the vehicle's Data Link Connector (DLC).

Instruments and Controls

107

The DLC is under the instrument panel to the left of the steering wheel. Connecting devices that are not used to perform an Emissions Inspection/Maintenance test or to service the vehicle may affect vehicle operation See Add-On Electrical Equipment 0 223. See your dealer if assistance is needed. The vehicle may not pass inspection if: . The light is on when the engine

is running.

. The light does not come on

when the ignition is in ON/RUN with the engine not running for Key Access or in Service Only Mode for Keyless Access.

. Critical emission control systems

have not been completely diagnosed. If this happens, the vehicle would not be ready for inspection and might require several days of routine driving before the system is ready for inspection. This can happen if the 12-volt battery has recently

been replaced or run down, or if the vehicle has been recently serviced.

See your dealer if the vehicle will not pass or cannot be made ready for the test.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

Metric

English

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

108

Instruments and Controls

This light should come on briefly when the engine is started. If it does not come on then, have it fixed so it will be ready to warn you if there is a problem. When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means the vehicle has a brake problem.

{ Warning

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

Antilock Brake System (ABS) Warning Light

For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then goes off. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not

have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light 0 107. For vehicles with a Driver Information Center (DIC), see Brake System Messages 0 116 for all brake-related DIC messages.

Lane Departure Warning (LDW) Light

If equipped, this light comes on briefly while starting the vehicle. If it does not come on, have the vehicle serviced. This light is green if LDW is on and ready to operate. This light changes to amber and flashes to indicate that the lane marking has been crossed without using a turn signal in that direction.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

See Lane Departure Warning (LDW) 0 213.

Vehicle Ahead Indicator

If equipped, this indicator will display green when a vehicle is detected ahead and amber when you are following a vehicle ahead much too closely. See Forward Collision Alert (FCA) System 0 210.

Traction Off Light

Instruments and Controls

109

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control/Electronic Stability Control 0 202.

StabiliTrak® OFF Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If StabiliTrak and TCS are off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems, and the warning light turns off. See Traction Control/Electronic Stability Control 0 202.

Traction Control System (TCS)/StabiliTrak® Light

This light comes on briefly when the engine is started.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

110

Instruments and Controls

If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See Traction Control/Electronic Stability Control 0 202.

Tire Pressure Light

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages 0 120. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure 0 267.

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation 0 270.

Engine Oil Pressure Light

Caution

Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil low can also damage the engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

This light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Low Fuel Warning Light

This light is near the fuel gauge and comes on briefly when the ignition is turned on as a check to show it is working. It also comes on when the fuel tank is low on fuel. The light turns off when fuel is added. If it does not, have the vehicle serviced.

Instruments and Controls

111

Security Light

High-Beam On Light

This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer 0 132.

Front Fog Lamp Light

The security light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation (Key Access) 0 40 or Immobilizer Operation (Keyless Access) 0 41.

The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps 0 135.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

112

Instruments and Controls

Lamps On Reminder

Door Ajar Light

This light comes on when the exterior lamps are in use. See Exterior Lamp Controls 0 132.

Cruise Control Light

This light comes on in the Driver Information Center (DIC) when a door is open or not securely latched. Before driving, check that all doors are properly closed.

The cruise control light is white when the cruise control is on and ready, and turns green when the cruise control is set and active. The light goes out when the cruise control is turned off. See Cruise Control 0 204.

Information Displays

Center Stack Display Infotainment and vehicle personalization information displays in the center stack screen. See: . The navigation system manual

and Infotainment 0 139.

. Vehicle Personalization 0 122. The center stack controls only need a light touch to operate and work best with bare hands. The controls will work with most gloves although they may take longer to respond. Use the finger pad rather than the finger tip to minimize response time. If the controls are not responding, remove the gloves.

Driver Information Center (DIC) The DIC displays information about the vehicle. It also displays warning messages if a system problem is

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

detected. See Vehicle Messages 0 115. All messages appear in the DIC display in the center of the instrument cluster. The vehicle may also have features that can be customized through the controls on the radio. See Vehicle Personalization 0 122. DIC Operation and Displays The DIC has different displays, which can be accessed by using the DIC buttons on the turn signal lever to the left of the steering wheel. The DIC displays trip, fuel, vehicle system information, and warning messages if a system problem is detected.

DIC Buttons

1. SET/CLR: Press to set or clear

the menu item displayed.

Instruments and Controls

113

2. w / x (Band): Use the band

to scroll through the items in each menu.

3. MENU: Press to display the

Trip/Fuel menu and the Vehicle Information menu. This button is also used to return to or exit the last screen displayed on the DIC.

Trip/Fuel Menu Items Press MENU on the turn signal lever until Trip/Fuel Menu is displayed. Use w / x to scroll through the menu items. The following is the list of all possible trip/fuel displays. Some of the items may not be available for your particular vehicle. . Digital Speedometer . Trip 1
. Trip 2
. Fuel Range . Average Fuel Economy and Instantaneous Fuel Economy

. Average Vehicle Speed

. Timer . Navigation

Digital Speedometer The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.

Trip 1 and Trip 2
This display shows the current distance traveled, in either kilometers (km) or miles (mi), since the last reset for the trip odometer. The trip odometer can be reset to zero by pressing SET/CLR while the trip odometer display is showing.

Fuel Range This display shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Fuel range cannot be reset.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

114

Instruments and Controls

Average Fuel Economy and Instantaneous Fuel Economy This display shows the approximate average liters per 100 kilometers (L/ 100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. This number reflects only the approximate average fuel economy that the vehicle has right now, and will change as driving conditions change. The fuel economy can be reset by pressing SET/CLR while the Average Fuel Economy display is showing. The instantaneous fuel economy display shows the current approximate fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg). Unlike average economy, this display cannot be reset.

Average Vehicle Speed This display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is

calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing SET/CLR while the Average Vehicle Speed display is showing.

Timer This display can be used as a timer. To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR.

Navigation This display is used for the Turn-by-Turn Navigation, if equipped.

Vehicle Information Menu Items Press MENU on the turn signal lever until Vehicle Information menu is displayed. Use w / x to scroll through the menu items. The following is the list of all possible vehicle information displays. Some of the items may not be available for your particular vehicle. . Display Units . Tire Pressure . Remaining Oil Life . Battery

Display Units Move w / x to switch between metric or US when the Unit display is active. Press SET/CLR to confirm the setting. This will change the displays on the cluster and DIC to either metric or English (US) measurements.

Tire Pressure The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Instruments and Controls

115

engine oil life system, press SET/ CLR while the Oil Life display is active. See Engine Oil Life System 0 232.

Battery This display, available on some vehicles, shows the current battery voltage. If the voltage is in the normal range, the value will display. For example, the display may read Battery Voltage 15.0 Volts. The vehicle's charging system regulates voltage based on the state of the battery. The battery voltage can fluctuate while viewing this information on the DIC. This is normal. See Charging System Light 0 105. If there is a problem with the battery charging system, the DIC will display a message.

Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SET/CLR. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the messages does not correct the problem. The following are some of the vehicle messages that may be displayed depending on your vehicle content.

in either kilopascal (kPa) or pounds per square inch (psi). See Tire Pressure Monitor System 0 269 and Tire Pressure Monitor Operation 0 270.

Remaining Oil Life This display shows an estimate of the oil's remaining useful life. If Remaining Oil Life 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages 0 117. The oil should changed as soon as possible. See Engine Oil 0 230. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended. See Maintenance Schedule 0 309. Remember, the Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

116

Instruments and Controls

Battery Voltage and Charging Messages

BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery - North America 0 241. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.

Brake System Messages

Cruise Control Messages

BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid 0 240. SERVICE BRAKE ASSIST This message may be displayed when there is a problem with the brake boost assist system. When this message is displayed, the brake boost assist motor might be heard operating and you might notice pulsation in the brake pedal. This is normal under these conditions. Take the vehicle to your dealer for service.

Compass Messages

CAL This message is displayed when the compass needs to be calibrated. See Compass 0 98. – – Dashes will be displayed if the compass needs service. See your dealer for service.

CRUISE SET TO XXX This message displays when the cruise control is set and shows the speed it was set to. See Cruise Control 0 204.

Door Ajar Messages

DRIVER DOOR OPEN This message will display when the driver door is open. Close the door completely. HOOD OPEN This message will display when the hood is open. Close the hood completely. LEFT REAR DOOR OPEN This message will display when the driver side rear door is open. Close the door completely. PASSENGER DOOR OPEN This message will display when the front passenger door is open. Close the door completely.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

RIGHT REAR DOOR OPEN This message will display when the passenger side rear door is open. Close the door completely. TRUNK OPEN This message will display when the trunk is open. Close the trunk completely.

Engine Cooling System Messages

A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle.

Instruments and Controls

117

If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. COOLANT LEVEL LOW ADD COOLANT This message will display if the coolant is low. See Engine Coolant 0 235. ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When the engine oil is changed, be sure to reset the Oil Life System. See Engine Oil Life System 0 232, Driver Information Center (DIC) 0 112, Engine Oil 0 230, and Maintenance Schedule 0 309. ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down. OIL PRESSURE LOW— STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

118

Instruments and Controls

Engine Power Messages

ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible.

TIGHTEN GAS CAP This message displays when the fuel cap is not on tight. Tighten the fuel cap.

Key and Lock Messages

NO REMOTE DETECTED This message displays when the transmitter battery is weak on vehicles with Keyless Access. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation 0 27. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation 0 27.

USE TRANSMITTER POCKET TO START This message displays when trying to start the vehicle if an RKE transmitter is not detected. The transmitter battery may be weak. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation 0 27.

Lamp Messages

AUTOMATIC LIGHT CONTROL ON/OFF This message is displayed when the automatic light control has been turned on or off. See Automatic Headlamp System 0 133. CHECK XXX TURN SIGNAL LAMP When one of the turn signals is out, this message displays to show which bulb needs to be replaced. See Bulb Replacement 0 245 and Replacement Bulbs 0 252.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Instruments and Controls

119

TURN SIGNAL ON This message is displayed if the turn signal has been left on. Turn off the turn signal.

Object Detection System Messages

FORWARD COLLISION ALERT OFF If your vehicle has the Forward Collision Alert (FCA) system, this message may display if the FCA system cannot activate due to a temporary condition. See Forward Collision Alert (FCA) System 0 210. FRONT CAMERA BLOCKED, CLEAN WINDSHIELD This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled because the camera view is blocked and cannot operate properly. It may also activate during heavy rain or due to road spray. To clean the system,

clean the outside of the windshield area in front of the LDW/FCA camera sensor. LANE DEPARTURE WARNING UNAVAILABLE This message may appear if LDW does not activate due to a temporary condition. PARK ASSIST OFF This message displays when the parking assist system has been turned off or when there is a temporary condition causing the system to be disabled. See Parking Assist 0 208. SERVICE FRONT CAMERA This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled and need service. See your dealer. SERVICE PARK ASSIST This message displays if there is a problem with the Rear Parking Assist (RPA) system. Do not use

this system to help you park. See Parking Assist 0 208. See your dealer for service. SERVICE SIDE DETECTION SYSTEM If this message appears, the system needs service. Take the vehicle to your dealer. SIDE BLIND ZONE ALERT OFF This message indicates that the driver has turned the system off. SIDE DETECTION SYSTEM UNAVAILABLE This message indicates that the SBZA system is disabled because the sensor is blocked and cannot detect vehicles in the blind zone. The sensor may be blocked by mud, dirt, snow, ice, or slush. This message may also activate during heavy rain or due to road spray. The vehicle does not need service.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

120

Instruments and Controls

Ride Control System Messages

SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive; however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly.

Security Messages

Tire Messages

THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.

Service Vehicle Messages

SERVICE AC SYSTEM This message displays if there is a problem with the air conditioning system. Take the vehicle to your dealer for service. SERVICE POWER STEERING This message displays and a chime may sound when there may be a problem with the power steering system. If this message displays and a reduction in steering performance or loss of power steering assistance is noticed, see your dealer. SERVICE VEHICLE SOON This message displays if there is a problem with the vehicle. Take the vehicle to your dealer for service.

SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation 0 270. TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation 0 270. TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. The low tire pressure warning light will also come on. See Tire Pressure Light 0 110. If a tire pressure message displays, inflate the tires until the tire pressure is equal to the values shown on the Tire and Loading Information label.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Instruments and Controls

121

the location of the windshield washer reservoir. Also, see Washer Fluid 0 239 for more information.

Window Messages

OPEN, THEN CLOSE DRIVER/ PASSENGER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to program each front window for the express-up feature to work. See Power Windows 0 44.

See Tires 0 260, Vehicle Load Limits 0 183, and Tire Pressure 0 267. More than one tire pressure message can be received at a time. The DIC also shows the tire pressure values. See Driver Information Center (DIC) 0 112.

Transmission Messages

SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT DENIED This message displays when attempting to use the automatic transmission manual mode to shift to too low or too high of a gear. See Manual Mode 0 199. SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when turning the ignition off or removing the key from the vehicle if the vehicle is not in P (Park).

TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Vehicle Reminder Messages

ICE POSSIBLE DRIVE WITH CARE This message displays when ice conditions are possible.

Washer Fluid Messages

WASHER FLUID LOW ADD FLUID This message displays when the windshield washer fluid is low. Fill the windshield washer reservoir as soon as possible. See Engine Compartment Overview 0 229 for

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

122

Instruments and Controls

Vehicle Personalization Use the audio system controls to access the personalization menus for customizing vehicle features. The following are all possible personalization features. Depending on the vehicle, some may not be available.

Infotainment System Audio System Controls

Using the Faceplate TUNE/MENU Knob . Press to enter, select, or activate

a highlighted menu option.

. Turn to highlight a menu option. . Press to enable or disable a

system setting.

} BACK . Press to exit a menu. . Press to return to a previous

screen.

Using the Touch Screen Press a screen feature to:

. View more feature options. . Enable or disable the feature. w : Press to scroll up. x : Press to scroll down. Back : Press to return to the previous menu. To access the personalization menu: 1. Press Config on the Home

page on the infotainment system display or CONFIG on the faceplate.

2. Select the desired feature to

display a list of available options.

3. Select the desired feature

setting.

Personalization Menus The following list of menu items may be available: . Languages . Time and Date . Radio Settings . Phone Settings

. Navigation Settings . Display Settings . Vehicle Settings Each menu is detailed in the following information. Languages Select Languages, then select from the available language(s). Time and Date Manually set the time and date. See Clock 0 98. Radio Settings Select and the following may display: . Auto Volume . Gracenote Options . XM Channel Art . Max Startup Volume . Number of Favorites Pages . XM Categories . Software Versions Menu

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Auto Volume This feature adjusts the volume to minimize the effects of unwanted background noise that can result from changing road surfaces, driving speeds, or open windows. This feature works best at lower volume settings where background noise is typically louder than the sound system volume. Select Off, Low, Medium, or High.

Gracenote Options Select and the following may display: . Normalization

Normalization This feature improves voice recognition and media groupings. See “CD Player,” “USB,” “Auxiliary Devices,” and “Bluetooth Audio” in the infotainment manual. Select to enable or disable.

XM Channel Art This feature turns the XM Audio page background on the XM Channel display on and off.

Instruments and Controls

123

Select to enable or disable.

Max Startup Volume This feature sets the maximum startup volume. If the vehicle is started and the volume is greater than this level, the volume is adjusted to this level. Press + or − to increase or decrease the volume.

Number of Favorites Pages Press to set the number of favorites to display. Select the desired number.

XM Categories This allows which available XM Categories are used and displayed. Press to enable or disable available categories.

Software Versions Menu Press to display information about the system and update software if available.

Phone Settings Select and the following may display: . Bluetooth

Bluetooth Select and the following may display: . Device List . Pair Device

Device List Select to connect to a different phone source, disconnect a phone, or delete a phone.

Pair Device Select to pair a new device. See “Pairing a Phone/Device” in “Bluetooth” in the infotainment manual. Navigation Settings See “Navigation Settings” in “Configure Menu” in the infotainment manual.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

124

Instruments and Controls

Display Settings Press and the following may display: . Home Page Menu . Rear Camera Options . Display Off . Map Settings

Home Page Menu Select and the following may display: . Customize . Sort . Restore Home Page Defaults

Customize This feature allows the selection of what icons will be on the first Home Page. Select and follow the screen prompts.

Sort This feature allows the icons on the Home Page to be moved.

Select and follow the screen prompts.

Restore Home Page Defaults This feature will restore the Home Page to the factory settings. Select and follow the screen prompts.

Rear Camera Options Select and the following may display: . Symbols . Guiding Lines

Symbols Select to turn the rear camera symbols on or off. See Rear Vision Camera (RVC) 0 206.

Guiding Lines Select to turn the rear camera guiding lines on or off. See Rear Vision Camera (RVC) 0 206.

Display Off Press to turn the display off. The display will return when any radio buttons are pressed or the screen is touched (if equipped).

Map Settings See “Map Settings” in “Configure Menu” in the infotainment manual. Vehicle Settings Select and the following may display: . Climate and Air Quality . Comfort and Convenience . Collision/Detection Systems . Lighting . Power Door Locks . Remote Lock/Unlock/Start . Return to Factory Settings? Climate and Air Quality Select and the following may display: . Auto Fan Speed . Remote Start Heated Seats

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Instruments and Controls

125

. Auto Defog . Auto Rear Defog

Auto Fan Speed This allows for selecting the automatic fan speed. It can be adjusted to run lower or higher than normal. Select High, Medium, or Low.

Remote Start Heated Seats When turned on, this feature will turn the heated seats on when using remote start on cold days. Select On or Off.

Auto Defog Only vehicles with dual automatic climate control will have this option. This allows for turning the auto defog on or off. Select On or Off.

Auto Rear Defog This will allow for turning the auto rear defog on or off. This feature will automatically turn on the rear window defogger when it is cold outside.

Select On or Off. Comfort and Convenience Select and the following may display: . Easy Exit Driver Seat . Chime Volume . Reverse Tilt Mirror

Easy Exit Driver Seat This feature moves the seat rearward allowing the driver more room to exit the vehicle. See “Easy Exit Driver Seat” under Memory Seats 0 52. Select On or Off.

Chime Volume This allows selection of the chime volume level. Select Normal or High.

Reverse Tilt Mirror When on, both the driver and passenger mirrors will tilt downward when the vehicle is shifted to R (Reverse) to improve visibility of the ground near the rear wheels.

They will return to their previous driving position when the vehicle is shifted out of R (Reverse), the ignition is turned to OFF, or the vehicle is left in R (Reverse). See Reverse Tilt Mirrors 0 42. Select On or Off. Collision/Detection Systems Select and the following may display: . Park Assist . Side Blind Zone Alert (SBZA) . Rear Cross Traffic Alert

Park Assist This allows the Park Assist feature to be turned on or off. Select On or Off. See Parking Assist 0 208.

Side Blind Zone Alert (SBZA) This allows the SBZA feature to be turned on or off. Select On or Off. See Side Blind Zone Alert (SBZA) 0 211.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

126

Instruments and Controls

Rear Cross Traffic Alert This allows the feature to be turned on or off. Select Off or On. See Rear Vision Camera (RVC) 0 206. Lighting Select and the following may display: . Vehicle Locator Lights . Exit Lighting

Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. The vehicle locator lights come on when unlocking the vehicle with the RKE transmitter. Select On or Off.

Exit Lighting This allows for selecting how long the exterior lamps stay on when leaving the vehicle and it is dark outside. Select Off, 30 Seconds, 1 Minute, or 2 Minutes.

Power Door Locks Select and depending on the radio the following may display: . Open Door Anti Lock Out . Unlocked Door Anti Lock Out . Auto Door Unlock . Delayed Door Lock

Open Door Anti Lock Out or Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open. If Off is selected, the Delayed Door Lock menu will be available and the door will lock as programmed through this menu. Select to turn On or Off.

Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park). Select All Doors, Driver Door, or Off.

Delayed Door Lock When on, this feature will delay the locking of the doors until five seconds after the last door is

closed. Three chimes will signal delayed locking is in use. Press either the power lock button or Q on the RKE transmitter twice to override the delayed locking feature and immediately lock all of the doors. Select to turn On or Off. Remote Lock/Unlock/Start Select and depending on the radio the following may display: . Remote Unlock Feedback . Unlock Feedback (Lights) . Remote Lock Feedback . Locking Feedback . Remote Door Unlock . Door Unlock Options . Memory Remote Recall . Remote Left in Vehicle Reminder . Relock Remote Door . Passive Door Unlock . Passive Door Lock

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Instruments and Controls

127

Remote Unlock Feedback or Unlock Feedback (Lights) When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Select On or Off. Press TUNE/ MENU to confirm and go back to the last menu.

Remote Lock Feedback or Locking Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Press TUNE/MENU when Locking Feedback is highlighted. Turn the TUNE/MENU knob to select Lights and Horn, Lights Only, Horn Only, or Off. Press TUNE/MENU to confirm and go back to the last menu.

Remote Door Unlock or Door Unlock Options This allows selection of which doors will unlock when pressing K on the RKE transmitter.

Press TUNE/MENU when Door Unlock Options is highlighted. Turn the TUNE/MENU knob to select All Doors or Driver Door Only. When set to Driver Door Only, the driver door will unlock the first time K is pressed and all doors will unlock when K is pressed a second time. When set to All Doors, all of the doors will unlock at the first press of K. Press TUNE/MENU to confirm and go back to the last menu.

Memory Remote Recall This allows the Memory Remote Recall feature to be turned on or off. When on, this feature will recall the current driver's last seat and outside mirror positions upon unlocking the driver door with the RKE transmitter, and opening that door. The current driver is identified when the RKE transmitter is used to unlock the driver door. If equipped with Keyless Access, the recall will occur upon opening the driver door. See “Recalling RKE Memory Positions” under Memory Seats 0 52.

Press TUNE/MENU when Memory Remote Recall is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.

Remote Left in Vehicle Reminder This allows the Remote Left in Vehicle Reminder feature to be turned on or off. If on, the horn will chirp if a remote is left in the vehicle. Press TUNE/MENU when Remote Left in Vehicle Reminder is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.

Relock Remote Door When on, the doors will automatically lock after a period of time if the vehicle is not entered or exited. Press TUNE/MENU when Relock Remote Door is highlighted. Turn the TUNE/MENU knob to select On

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

128

Instruments and Controls

or Off. Press TUNE/MENU to confirm and go back to the last menu.

Passive Door Unlock This allows selection of which doors are unlocked by pressing the button on the outside door handle. Press TUNE/MENU when Passive Door Unlock is highlighted. Turn the TUNE/MENU knob to select All Doors or Driver Door. Press TUNE/ MENU to confirm and go back to the last menu.

Passive Door Lock This allows for turning Passive Locking off, on, or on with feedback.

Press TUNE/MENU when Passive Door Lock is highlighted. Turn the TUNE/MENU knob to select Off, On, or On with Active Horn Chirp. Press TUNE/MENU to confirm and go back to the last menu. Return to Factory Settings? Select Return to Factory Settings? for the option to return all vehicle personalization to the default settings. Turn the TUNE/MENU knob to select Yes or No. Press TUNE/MENU to confirm and go back to the last menu.

Universal Remote System See Radio Frequency Statement 0 335.

Universal Remote System Programming

If equipped, these buttons are in the overhead console. This system can replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. These instructions refer to a garage door opener, but can be used for other devices. Do not use the Universal Remote system with any garage door opener that does not have the stop and

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Instruments and Controls

129

reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read these instructions completely before programming the Universal Remote system. It may help to have another person assist with the programming process. Keep the original hand-held transmitter for use in other vehicles as well as for future programming. Erase the programming when vehicle ownership is terminated. See “Erasing Universal Remote System Buttons” later in this section. To program a garage door opener, park outside directly in line with and facing the garage door opener receiver. Clear all people and objects near the garage door. Make sure the hand-held transmitter has a new battery for quick and accurate transmission of the radio-frequency signal.

Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or see www.homelink.com. Programming involves time-sensitive actions, and may time out causing the procedure to be repeated. To program up to three devices: 1. Hold the end of the hand-held transmitter about 3 to 8 cm (1
to 3 in) away from the Universal Remote system buttons with the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver.

2. At the same time, press and

hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release either button until

the indicator light changes from a slow to a rapid flash. Then release both buttons. Some garage door openers may require substitution of Step 2 with the procedure under “Radio Signals for Canada and Some Gate Operators” later in this section.

3. Press and hold the newly

programmed Universal Remote system button for five seconds while watching the indicator light and garage door activation.

If the indicator light stays on continuously or the garage door moves when the button is pressed, then programming is complete. There is no need to complete Steps 4–6. If the indicator light does not come on or the garage door does not move, a second button press may be required. For a second time, press and hold the newly programmed button

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

130

Instruments and Controls

for five seconds. If the light stays on or the garage door moves, programming is complete. If the indicator light blinks rapidly for two seconds, then changes to a solid light and the garage door does not move, continue with programming Steps 4–6.

Learn or Smart Button

4. After completing Steps 1–3,

locate the Learn or Smart button inside the garage on the garage door opener receiver. The name and color of the button may vary by manufacturer.

5. Press and release the Learn or

6.

Smart button. Step 6 must be completed within 30 seconds of pressing this button. Inside the vehicle, press and hold the newly programmed Universal Remote system button for two seconds and then release it. If the garage door does not move or the lamp on the garage door opener receiver does not flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release it.

The Universal Remote system should now activate the garage door. Repeat the process for programming the two remaining buttons.

Radio Signals for Canada and Some Gate Operators For questions or programming help call 1-800-355-3515 or see www.homelink.com. Canadian radio-frequency laws and some U.S. gate operators require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming. If the programming did not work, replace Step 2 under “Programming the Universal Remote System” with the following: Press and hold the Universal Remote system button while pressing and releasing the hand-held transmitter button every two seconds until the signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Instruments and Controls

131

Reprogramming a Single Universal Remote System Button To reprogram any of the system buttons: 1. Press and hold any one of the

buttons. Do not release the button.

2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.”

Universal Remote System Operation

Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least one-half second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons Erase all programmed buttons when vehicle ownership is terminated. To erase: 1. Press and hold the two outside buttons until the indicator light begins to flash. This should take about 10 seconds.

2. Release both buttons.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

Lighting

132
Lighting

Exterior Lighting

Exterior Lighting

Exterior Lamp Controls

Exterior Lamp Controls . . . . . . . 132
Exterior Lamps Off

Reminder . . . . . . . . . . . . . . . . . . . 132

Headlamp High/Low-Beam

Changer . . . . . . . . . . . . . . . . . . . . 132
Flash-to-Pass . . . . . . . . . . . . . . . . 133
Daytime Running

Lamps (DRL) . . . . . . . . . . . . . . . 133

Automatic Headlamp

System . . . . . . . . . . . . . . . . . . . . . . 133
Hazard Warning Flashers . . . . . 134
Turn and Lane-Change

Signals . . . . . . . . . . . . . . . . . . . . . . 134
Fog Lamps . . . . . . . . . . . . . . . . . . . 135

Interior Lighting

Instrument Panel Illumination

Control . . . . . . . . . . . . . . . . . . . . . . 135
Courtesy Lamps . . . . . . . . . . . . . . 135
Dome Lamps . . . . . . . . . . . . . . . . . 136
Reading Lamps . . . . . . . . . . . . . . 136

Lighting Features

Entry Lighting . . . . . . . . . . . . . . . . 137
Exit Lighting . . . . . . . . . . . . . . . . . . 137
Battery Load Management . . . 137

The exterior lamp control is on the instrument panel on the left side of the steering wheel. Turn the control to the following positions: O (Off) : Turns off the exterior lamps. The knob returns to the AUTO position after it is released. Turn to O again to reactivate the AUTO mode. In Canada, the headlamps will automatically reactivate when the vehicle is shifted out of P (Park).

AUTO (Automatic) : Automatically turns the exterior lamps on and off, depending on outside lighting. ; (Parking Lamps) : Turns on the parking lamps including all lamps, except the headlamps. 2 (Headlamps) : Turns on the headlamps together with the parking lamps and instrument panel lights.

Exterior Lamps Off Reminder A warning chime sounds if the driver door is opened while the ignition is off and the exterior lamps are on.

Headlamp High/ Low-Beam Changer 2 3 (Headlamp High/Low-Beam Changer) : Push the turn signal lever away from you and release, to turn the high beams on. To return to low beams, push the lever again or pull it toward you and release.

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15

DRL. The DRL will come on when all of the following conditions are met: . The ignition is on. . The exterior lamp control is

in AUTO.

. The light sensor determines it is

daytime.

. The vehicle is not in P (Park). When the DRL are on, the taillamps, sidemarker lamps, instrument panel lights, and other lamps will not be on. The DRL turn off when the headlamps are turned to O or the ignition is off. This vehicle may have a DRL disabling function. When the DRL are on and a turn signal is activated, the DRL on that side will be off until the turn signal goes off.

Lighting

133

Automatic Headlamp System When the exterior lamp control is set to AUTO and it is dark enough outside, the headlamps come on automatically.

There is a light sensor on top of the instrument panel. Do not cover the sensor, otherwise the headlamps will come on when they are not needed. The system may also turn on the headlamps when driving through a parking garage or tunnel.

This indicator light turns on in the instrument cluster when the high-beam headlamps are on.

Flash-to-Pass To flash the high beams, pull the turn signal lever toward you, and release.

Daytime Running Lamps (DRL) DRL can make it easier for others to see the front of your vehicle during the day. Fully functional DRL are required on all vehicles first sold in Canada. The DRL system turns on the low-beam headlamps at a reduced brightness. For vehicles with High Intensity Discharge (HID) headlamps, there is a dedicated

Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15