Download PDF Manual

If the overload is caused by an electrical problem and not snow or ice, be sure to get it fixed.


Fuses The wiring circuits in the vehicle are protected from short circuits by fuses. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure to replace a bad fuse with a new one of the identical size and rating.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


254


Vehicle Care


Fuses of the same amperage can be temporarily borrowed from another fuse location, if a fuse goes out. Replace the fuse as soon as possible. To identify and check fuses, circuit breakers, and relays, see Engine Compartment Fuse Block 0 254 and Instrument Panel Fuse Block 0 258.


Engine Compartment Fuse Block The engine compartment fuse block is on the driver side of the engine compartment, near the battery.


Caution


Spilling liquid on any electrical component on the vehicle may damage it. Always keep the covers on any electrical component.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Vehicle Care


255


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


256


Vehicle Care


The vehicle may not be equipped with all of the fuses, relays, and features shown.


Mini Fuses


Usage


10


Transmission Control Module Battery Engine Control Module Battery (LTG)/ Air Conditioning Compressor Clutch (LKW) Air Conditioning Compressor Clutch (LTG) Air Conditioning Compressor Clutch (LTG) Engine Control Module Battery (LKW) Engine Control Module Ignition (LKW) Spare Ignition Coils Engine Control Module


Mini Fuses


Usage


Mini Fuses


Usage


11
13


14


15
16
17
18


20


23
29


30


31


32


Emissions Transmission Module Ignition Cabin Heater Coolant Pump Spare Aero Shutter Spare R/C Dual Battery Isolator Module Transmission Auxiliary Oil Pump (LKW) Spare (LKW) Left Seat Power Lumber Control Right Seat Power Lumber Control Chassis Control Module Back-Up Lamps/ Interior Lamps


33
34


35
37
38
46
47
48
49


50


51
52
53


54


Front Heated Seats Antilock Brake System Valve Amplifier Right High Beam Left High Beam Cooling Fan Emissions Foglamp Low Beam HID Headlamp Right Low Beam HID Headlamp Left Horn/Dual Horn Cluster Ignition Inside Rearview Mirror/Rear Camera/ Fuel Module Ignition Heating, Ventilation, and Air Conditioning Module Ignition


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Mini Fuses


Usage


J-Case Fuses


Usage


55


56
57
60
62


66
67
69


70


71


J-Case Fuses


12
21


Front Power Windows/Mirrors Windshield Washer Spare Heated Mirror Canister Vent Solenoid Spare Fuel Module Battery Voltage Sensor Lane Departure/Rear Parking Aid/Side Blind Zone Assist PEPS BATT


Usage


Front Wiper Starter 1
Rear Power Window


22
24
25
26


27
28
41
42
44
45
59


Sunroof Front Power Window PEPS MTR Antilock Brake System Pump Not Used Rear Defogger Brake Vacuum Pump Cooling Fan K2
Starter 2
Cooling Fan K1
Air Pump Emissions


Mini


Relays


Usage


13
15
16


Powertrain Cooling Fan K2
Cooling Fan K1
Run/Crank Spare


Vehicle Care


257


Mini


Relays


17


Micro Relays


Usage


Window/Mirror Defogger


Usage


10
11


14


Air Conditioning Compressor Clutch Starter Solenoid Front Wiper Speed Front Wiper On Spare Transmission Auxiliary Oil Pump (LKW) Cooling Fan K3
Starter 2
Solenoid (LKW) Headlamp Low Beam/DRL


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


258


Vehicle Care


Instrument Panel Fuse Block


Pull the door toward you to release it from the hinge.


The instrument panel fuse block is in the instrument panel, on the driver side of the vehicle. To access the fuses, open the fuse panel door by pulling down at the top. Press in on the sides of the door to release it from the instrument panel.


Instrument Panel Fuse Block The vehicle may not be equipped with all of the fuses, relays, and features shown.


Fuses


Usage


Steering Wheel Controls Backlight Right Rear Turn Signal, Left Mirror Turn Signal, Left Front Turn Signal, Door Locks Left Stoplamp, Left DRL Lamp, Headlamp Control, Right Taillamp, Right


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Fuses


Usage


Fuses


Park/Sidemarker Lamps, Right Mirror Turn, Right Front Turn Signals Radio OnStar (If Equipped) Front Accessory Power Outlet Console Bin Power Outlet License Plate Lamp, Center High-Mounted Stoplamp, Rear Fog Lamps, Right Front Park/Sidemarker Lamps, LED Indicator Dim, Washer Pump, Right Stoplamp, Trunk Release Left Low-Beam Headlamp, DRL


10


11


12


13


14


15
16
17


18
19
20


21


Usage Body Control Module 8 (J-Case Fuse), Power Locks Front Heater Ventilation Air Conditioning/Blower (J-Case Fuse) Passenger Seat (Circuit Breaker) Driver Seat (Circuit Breaker) Diagnostic Link Connector Airbag, SDM Trunk Release Heater Ventilation Air Conditioning Controller Audio Main Displays Passenger Occupant Sensor Instrument Cluster


Vehicle Care


259


Fuses


22
23


24


25
26


Usage Ignition Switch Right Low-Beam Headlamp, DRL Ambient Light, Switch Backlighting (LED), Trunk Lamp, Shift Lock, Key Capture 110V AC Spare


Relays


K1
K2
K3


Usage Trunk Release Not Used Power Outlet Relay


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


260


Vehicle Care


Wheels and Tires


Tires Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer.


{ Warning


. Poorly maintained and


improperly used tires are dangerous.


. Overloading the tires can


cause overheating as a result of too much flexing. There could be a blowout and a serious crash. See Vehicle Load Limits 0 183.


(Continued)


Warning (Continued)


Warning (Continued)


. Underinflated tires pose


. Replace any tires that


the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when the tires are cold.


. Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when hitting a pothole. Keep tires at the recommended pressure.


. Worn or old tires can cause a crash. If the tread is badly worn, replace them.


(Continued)


have been damaged by impacts with potholes, curbs, etc. Improperly repaired tires can cause a crash. Only the dealer or an authorized tire service center should repair, replace, dismount, and mount the tires.


. Do not spin the tires in


excess of 56 km/h (35 mph) on slippery surfaces such as snow, mud, ice, etc. Excessive spinning may cause the tires to explode.


See Tire Pressure for High-Speed Operation 0 268 for inflation pressure adjustment for high-speed driving.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


All-Season Tires This vehicle may come with all-season tires. These tires are designed to provide good overall performance on most road surfaces and weather conditions. Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. Original equipment all-season tires can be identified by the last two characters of this TPC code, which will be “MS.” Consider installing winter tires on the vehicle if frequent driving on snow or ice-covered roads is expected. All-season tires provide adequate performance for most winter driving conditions, but they may not offer the same level of traction or performance as winter tires on snow or ice-covered roads. See Winter Tires 0 261.


Winter Tires This vehicle was not originally equipped with winter tires. Winter tires are designed for increased


traction on snow and ice-covered roads. Consider installing winter tires on the vehicle if frequent driving on ice or snow covered roads is expected. See your dealer for details regarding winter tire availability and proper tire selection. Also, see Buying New Tires 0 275. With winter tires, there may be decreased dry road traction, increased road noise, and shorter tread life. After changing to winter tires, be alert for changes in vehicle handling and braking. If using winter tires: . Use tires of the same brand and


tread type on all four wheel positions.


. Use only radial ply tires of the


same size, load range, and speed rating as the original equipment tires.


Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y, and ZR speed rated tires. If winter


Vehicle Care


261


tires with a lower speed rating are chosen, never exceed the tire's maximum speed capability.


Summer Tires This vehicle may come with high performance summer tires. These tires have a special tread and compound that are optimized for maximum dry and wet road performance. This special tread and compound will have decreased performance in cold climates, and on ice and snow. It is recommended that winter tires be installed on the vehicle if frequent driving at temperatures below approximately 5 °C (40 °F) or on ice or snow covered roads is expected. See Winter Tires 0 261.


Caution


High performance summer tires have rubber compounds that lose flexibility and may develop surface cracks in the tread area at temperatures below −7 °C


(Continued)


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


262


Vehicle Care


Caution (Continued)


(20 °F). Always store high performance summer tires indoors and at temperatures above −7 °C (20 °F) when not in use. If the tires have been subjected to −7 °C (20 °F) or less, let them warm up in a heated space to at least 5 °C (40 °F) for 24 hours or more before being installed or driving a vehicle on which they are installed. Do not apply heat or blow heated air directly on the tires. Always inspect tires before use. See Tire Inspection 0 273.


Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples show a typical passenger vehicle tire and a compact spare tire sidewall.


GM's TPC specifications meet or exceed all federal safety guidelines. (3) DOT (Department of Transportation) : The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. DOT Tire Date of Manufacture : The last four digits of the TIN indicate the tire manufactured date. The first two digits represent the week (01– 52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. (4) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the


Passenger (P-Metric) Tire Example (1) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section. (2) TPC Spec (Tire Performance Criteria Specification) : Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (5) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (6) Uniform Tire Quality Grading (UTQG) : Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading 0 277. (7) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load.


Compact Spare Tire Example (1) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (2) Temporary Use Only : The compact spare tire or temporary use tire should not be driven at speeds over 80 km/h (50 mph). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat. If the vehicle has a compact spare tire, see Compact Spare Tire 0 292 and If a Tire Goes Flat 0 280.


Vehicle Care


263


(3) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (4) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load. (5) Tire Inflation : The temporary use tire or compact spare tire should be inflated to 420 kPa (60 psi). For more information on tire pressure and inflation see Tire Pressure 0 267. (6) Tire Size : A combination of letters and numbers define a tire's width, height, aspect ratio,


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


264


Vehicle Care


construction type, and service description. The letter T as the first character in the tire size means the tire is for temporary use only. (7) TPC Spec (Tire Performance Criteria Specification) : Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.


Tire Designations


Tire Size The following is an example of a typical passenger vehicle tire size.


(4) Construction Code : A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction. (5) Rim Diameter : Diameter of the wheel in inches. (6) Service Description : These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.


Tire Terminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of


(1) Passenger (P-Metric) Tire : The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (2) Tire Width : The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (3) Aspect Ratio : A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item 3 of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight : The combined weight of optional accessories. Some examples of optional accessories are automatic transmission, power windows, power seats, and air conditioning. Aspect Ratio : The relationship of a tire's height to its width. Belt : A rubber coated layer of cords between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead : The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire : A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.


Cold Tire Pressure : The amount of air pressure in a tire, measured in kPa (kilopascal) or psi (pounds per square inch) before a tire has built up heat from driving. See Tire Pressure 0 267. Curb Weight : The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings : A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production.


Vehicle Care


265


GVWR : Gross Vehicle Weight Rating. See Vehicle Load Limits 0 183. GAWR FRT : Gross Axle Weight Rating for the front axle. See Vehicle Load Limits 0 183. GAWR RR : Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits 0 183. Intended Outboard Sidewall : The side of an asymmetrical tire that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure. Light Truck (LT-Metric) Tire : A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index : An assigned number ranging from 1 to 279
that corresponds to the load carrying capacity of a tire.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


266


Vehicle Care


Maximum Inflation Pressure : The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating : The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight : The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight : The number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lb). See Vehicle Load Limits 0 183. Occupant Distribution : Designated seating positions. Outward Facing Sidewall : The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that


contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire : A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure : Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure 0 267 and Vehicle Load Limits 0 183. Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated.


Sidewall : The portion of a tire between the tread and the bead. Speed Rating : An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction : The friction between the tire and the road surface. The amount of grip provided. Tread : The portion of a tire that comes into contact with the road. Treadwear Indicators : Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1.6 mm (1/ 16 in) of tread remains. See When It Is Time for New Tires 0 274. UTQGS (Uniform Tire Quality Grading Standards) : A tire information system that provides consumers with ratings for a tire's traction, temperature, and treadwear. Ratings are


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading 0 277. Vehicle Capacity Weight : The number of designated seating positions multiplied by 68 kg (150 lb) plus the rated cargo load. See Vehicle Load Limits 0 183. Vehicle Maximum Load on the Tire : Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard : A label permanently attached to a vehicle showing the vehicle capacity weight and the original equipment tire size and recommended inflation pressure. See “Tire and Loading Information Label” under Vehicle Load Limits 0 183.


Tire Pressure Tires need the correct amount of air pressure to operate effectively.


Caution


Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:


. Tire overloading and


overheating which could lead to a blowout.


. Premature or irregular wear. . Poor handling. . Reduced fuel economy. Overinflated tires, or tires that have too much air, can result in:


. Unusual wear.


(Continued)


Vehicle Care


267


Caution (Continued)


. Poor handling. . Rough ride. . Needless damage from


road hazards.


The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures. The recommended pressure is the minimum air pressure needed to support the vehicle's maximum load carrying capacity. See Vehicle Load Limits 0 183. How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


268


Vehicle Care


When to Check Check the tires once a month or more. Do not forget the compact spare, if the vehicle has one. The cold compact spare tire pressure should be at 420 kPa (60 psi). See Compact Spare Tire 0 292.


How to Check Use a good quality pocket-type gauge to check tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no


further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air. Recheck the tire pressure with the tire gauge. Put the valve caps back on the valve stems to keep out dirt and moisture and prevent leaks. Use only valve caps designed for the vehicle by GM. TPMS sensors could be damaged and would not be covered by the vehicle warranty.


Tire Pressure for High-Speed Operation


{ Warning


Driving at high speeds, 160 km/h (100 mph) or higher, puts additional strain on tires.


(Continued)


Warning (Continued)


Sustained high-speed driving causes excessive heat buildup and can cause sudden tire failure. This could cause a crash, and you or others could be killed. Some high-speed rated tires require inflation pressure adjustment for high-speed operation. When speed limits and road conditions allow the vehicle to be driven at high speeds, make sure the tires are rated for high-speed operation, are in excellent condition, and are set to the correct cold tire inflation pressure for the vehicle load.


Vehicles with P235/50R18 size tires require inflation pressure adjustment when driving the vehicle at speeds of 160 km/h (100 mph) or higher. Set the cold inflation pressure to 270 kPa (39 psi). Vehicles with P245/40R19 size tires require inflation pressure adjustment when driving the vehicle at speeds


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


of 160 km/h (100 mph) or higher. Set the cold inflation pressure to 310 kPa (45 psi). Return the tires to the recommended cold tire inflation pressure when high-speed driving has ended. See Vehicle Load Limits 0 183 and Tire Pressure 0 267.


Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or


tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has


Vehicle Care


269


not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


270


Vehicle Care


alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation 0 270. See Radio Frequency Statement 0 335.


Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmits the tire pressure readings to a receiver in the vehicle.


The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and needs to be inflated to the proper pressure. A Tire and Loading Information label, attached to your vehicle, shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load Limits 0 183, for an example of the Tire and Loading Information label and its location. Also see Tire Pressure 0 267. The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection 0 273, Tire Rotation 0 273 and Tires 0 260.


When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the Tire and Loading Information label. See Vehicle Load Limits 0 183. A message to check the pressure in a specific tire displays in the Driver Information Center (DIC). The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed. For additional information and details about the DIC operation and displays see Driver Information Center (DIC) 0 112.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Caution


Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use only the GM approved tire sealant available through your dealer or included in the vehicle.


Factory-installed Tire Inflator Kits use a GM approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See Tire Sealant and Compressor Kit 0 281 for information regarding the inflator kit materials and instructions. TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for


about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message also displays. The malfunction light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause these to come on are: . One of the road tires has been


replaced with the spare tire. The spare tire does not have a TPMS sensor. The malfunction light and DIC message should go off after the road tire is replaced and the sensor matching process is performed successfully. See “TPMS Sensor Matching Process” later in this section.


. The TPMS sensor matching process was not done or not completed successfully after rotating the tires. The malfunction light and the DIC message should go off after successfully completing the sensor matching process. See "TPMS Sensor Matching Process" later in this section.


Vehicle Care


271


. One or more TPMS sensors are


missing or damaged. The malfunction light and the DIC message should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer for service.


. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended could prevent the TPMS from functioning properly. See Buying New Tires 0 275.


. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.


If the TPMS is not functioning properly it cannot detect or signal a low tire condition. See your dealer for service if the TPMS malfunction light and DIC message comes on and stays on.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


272


Vehicle Care


TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the vehicle’s tires or replacing one or more of the TPMS sensors. The TPMS sensor matching process should also be performed after replacing a spare tire with a road tire containing the TPMS sensor. The malfunction light and the DIC message should go off at the next ignition cycle. The sensors are matched to the tire/wheel positions, using a TPMS relearn tool, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear. See your dealer for service or to purchase a relearn tool. A TPMS relearn tool can also be purchased. See Tire Pressure Monitor Sensor Activation Tool at www.gmtoolsandequipment.com or call 1-800-GM TOOLS (1-800-468-6657).


There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. The TPMS sensor matching process is: 1. Set the parking brake. 2. Turn the ignition to ON/RUN


with the engine off or place the vehicle power mode in ON/ RUN/START. See Ignition Positions (Keyless Access) 0 187 or Ignition Positions (Key Access) 0 189.


3. Use the MENU button to select


the Vehicle Information Menu in the Driver Information Center (DIC).


A message asking if the process should begin should appear.


6. Press the SET/CLR button


again to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen.


7. Start with the driver side


front tire.


8. Place the relearn tool against


the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.


4. Use the thumbwheel to scroll to


9. Proceed to the passenger side


the Tire Pressure Menu Item screen.


front tire, and repeat the procedure in Step 8.


5. Press the SET/CLR button to


10. Proceed to the passenger side


begin the sensor matching process.


rear tire, and repeat the procedure in Step 8.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


11. Proceed to the driver side rear tire, and repeat the procedure in Step 8. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.


12. Turn the ignition to LOCK/OFF


or press STOP to turn the ignition off.


13. Set all four tires to the


recommended air pressure level as indicated on the Tire and Loading Information label.


Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month.


Replace the tire if: . The indicators at three or


more places around the tire can be seen.


. There is cord or fabric


showing through the tire's rubber.


. The tread or sidewall is


cracked, cut, or snagged deep enough to show cord or fabric.


. The tire has a bump, bulge,


or split.


. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.


Tire Rotation Tires should be rotated every 12 000 km (7,500 mi). See Maintenance Schedule 0 309.


Vehicle Care


273


Tires are rotated to achieve a more uniform wear for all tires. The first rotation is the most important. Anytime unusual wear is noticed, rotate the tires as soon as possible, check for proper tire inflation pressure, and check for damaged tires or wheels. If the unusual wear continues after the rotation, check the wheel alignment. See When It Is Time for New Tires 0 274 and Wheel Replacement 0 278.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


274


Vehicle Care


Use this rotation pattern when rotating the tires. Do not include the compact spare tire in the tire rotation. Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated. See Tire Pressure 0 267 and Vehicle Load Limits 0 183. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation 0 270. Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications 0 323.


{ Warning


Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come (Continued)


Warning (Continued)


off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.


Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.


When It Is Time for New Tires Factors such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.


Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. See Tire Inspection 0 273 and Tire Rotation 0 273. The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple factors including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. GM recommends that tires, including the spare if equipped, be replaced after six years, regardless of tread wear. The


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


tire manufacture date is the last four digits of the DOT Tire Identification Number (TIN) which is molded into one side of the tire sidewall. The first two digits represent the week (01–52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. This area should be free of grease, gasoline, or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.


Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating. GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number


Vehicle Care


275


will be followed by MS for mud and snow. See Tire Sidewall Labeling 0 262. GM recommends replacing worn tires in complete sets of four. Uniform tread depth on all tires will help to maintain the performance of the vehicle. Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. If proper rotation and maintenance have been done, all four tires should wear out at about the same time. See Tire Rotation 0 273. However, if it is necessary to replace only one axle set of worn tires, place the new tires on the rear axle. Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y and ZR speed rated tires. Never exceed the winter


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


276


Vehicle Care


tires’ maximum speed capability when using winter tires with a lower speed rating.


{ Warning


Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death. Only your dealer or authorized tire service center should mount or dismount the tires.


{ Warning


Mixing tires of different sizes, brands, or types may cause loss of control of the vehicle, resulting in a crash or other vehicle damage. Use the correct size, brand, and type of tires on all wheels.


{ Warning


Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving. A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.


If the vehicle tires must be replaced with a tire that does not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction (radial) as the original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed. See Tire Pressure Monitor System 0 269.


The Tire and Loading Information label indicates the original equipment tires on the vehicle. See Vehicle Load Limits 0 183.


Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, electronic stability control, or All-Wheel Drive, the performance of these systems can also be affected.


{ Warning


If different sized wheels are used, there may not be an acceptable level of performance and safety if (Continued)


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Warning (Continued)


tires not recommended for those wheels are selected. This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems developed for the vehicle, and have them properly installed by a GM certified technician.


See Buying New Tires 0 275 and Accessories and Modifications 0 226.


Uniform Tire Quality Grading The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of


most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter tires, compact spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:


Vehicle Care


277


Treadwear 200 Traction AA Temperature A All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.


Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


278


Vehicle Care


Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.


Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor


laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing are not necessary on a regular basis. Consider an alignment check if there is unusual tire wear or the vehicle is significantly pulling to one side or the other. Some slight pull to the left or right, depending on the crown of the road and/or other road surface variations such as troughs or ruts, is normal. If the vehicle is vibrating when driving on a smooth road, the tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.


Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.


{ Warning


Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.


Caution


The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis.


Used Replacement Wheels


{ Warning


Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.


Vehicle Care


279


Tire Chains


{ Warning


Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause loss of control and a crash. Use another type of traction device only if its manufacturer recommends it for the vehicle's tire size combination and road conditions. Follow that manufacturer's instructions. To avoid vehicle damage, drive slow and readjust or remove the traction device if it contacts the vehicle. Do not spin the wheels. If traction devices are used, install them on the front tires.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


280


Vehicle Care


If a Tire Goes Flat It is unusual for a tire to blow out while driving, especially if the tires are maintained properly. See Tires 0 260. If air goes out of a tire, it is much more likely to leak out slowly. But if there is ever a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.


{ Warning


Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.


{ Warning


Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could (Continued)


Warning (Continued)


be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.


If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers 0 134. { Warning Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall causing injury or death. Find a level place to change the tire. To help prevent the vehicle from moving:


1. Set the parking brake firmly. (Continued)


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Warning (Continued)


2. Put an automatic


transmission in P (Park) or a manual transmission in 1 (First) or R (Reverse).


3. Turn off the engine and do not restart while the vehicle is raised.


4. Do not allow passengers to


remain in the vehicle.


5. Place wheel blocks,


if equipped, on both sides of the tire at the opposite corner of the tire being changed.


This vehicle may come with a jack and spare tire or a tire sealant and compressor kit. To use the jacking equipment to change a spare tire safely, follow the instructions below. Then see Tire Changing 0 287. To use the tire sealant and compressor kit, see Tire Sealant and Compressor Kit 0 281.


When the vehicle has a flat tire (2), use the following example as a guide to assist you in the placement of wheel blocks (1), if equipped.


1. Wheel Block (If Equipped) 2. Flat Tire


The following information explains how to repair or change a tire.


Tire Sealant and Compressor Kit


{ Warning


Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may


(Continued)


Vehicle Care


281


Warning (Continued)


enter the vehicle. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust 0 196.


{ Warning


Overinflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


282


Vehicle Care


{ Warning


Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.


If this vehicle has a tire sealant and compressor kit, there may not be a spare tire, tire changing equipment, and on some vehicles there may not be a place to store a tire. The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (0.25 in) in the tread area of the tire. It can also be used to inflate an under inflated tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire


sealant and compressor kit to be effective. See Roadside Assistance Program 0 329. Read and follow all of the tire sealant and compressor kit instructions. The kit includes:


1. On/Off Button 2. Selector Switch (Sealant/Air


or Air Only)

Loading...
x