Download PDF Manual

by a ground fault detection function. An ungrounded outlet could cause an electric shock.


. Use a weatherproof,


heavy-duty, 15 amp-rated extension cord if needed. Failure to use the recommended extension cord in good operating condition, or using a damaged heater or extension cord, could make


(Continued)


Driving and Operating


193


Warning (Continued)


it overheat and cause a fire, property damage, electric shock, and injury.


. Do not operate the vehicle


with the heater cord permanently attached to the vehicle. Possible heater cord and thermostat damage could occur.


. While in use, do not let the


heater cord touch vehicle parts or sharp edges. Never close the hood on the heater cord.


. Before starting the vehicle,


unplug the cord, reattach the cover to the plug, and securely fasten the cord. Keep the cord away from any moving parts.


4. Before starting the engine, be


sure to unplug and store the cord as it was before to keep it away from moving engine parts.


The electrical cord is on the passenger side of the engine compartment, between the fender and the air cleaner. Check the heater cord for damage. If it is damaged, do not use it. See your dealer for a replacement. Inspect the cord for damage yearly.


3. Plug it into a normal, grounded


110-volt AC outlet.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


194


Driving and Operating


The length of time the heater should remain plugged in depends on several factors. Ask a dealer in the area where you will be parking the vehicle for the best advice on this.


Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the engine is turned off: . Audio System . Power Windows . Sunroof (if equipped) These features continue to work up to 10 minutes after the ignition is turned to LOCK/OFF. The power windows and sunroof will work until any door is opened. The radio continues to work until the driver door is opened. All these features operate when the key is in ON/RUN or ACC/ ACCESSORY.


Shifting Into Park 1. Hold the brake pedal down and


set the parking brake. See Parking Brake 0 200.


2. Move the shift lever into


P (Park) by holding in the button on the shift lever and pushing the shift lever all the way toward the front of the vehicle.


3. Turn the ignition to LOCK/OFF. 4. Remove the key (if equipped) and take it with you. If you can leave the vehicle with the ignition key in your hand, the vehicle is in P (Park).


Leaving the Vehicle with the Engine Running


{ Warning


It can be dangerous to leave the vehicle with the engine running. It could overheat and catch fire.


(Continued)


Warning (Continued)


It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park). See Shifting Into Park 0 194.


If you have to leave the vehicle with the engine running, be sure the vehicle is in P (Park) and the parking brake is firmly set before you leave it. After you have moved the shift lever into P (Park), hold the regular brake pedal down. Then, see if you can move the shift lever away from P (Park) without first pushing the button.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


If you can, it means that the shift lever was not fully locked in P (Park). Torque Lock Torque lock is when the weight of the vehicle puts too much force on the parking pawl in the transmission. This happens when parking on a hill and shifting the transmission into P (Park) is not done properly, then it is difficult to shift out of P (Park). To prevent torque lock, set the parking brake and then shift into P (Park). To find out how, see “Shifting Into Park” listed previously. If torque lock does occur, your vehicle may need to be pushed uphill by another vehicle to relieve the parking pawl pressure, so you can shift out of P (Park). If you are towing a trailer and parking on a hill, see Driving Characteristics and Towing Tips 0 218.


Shifting out of Park This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: . Prevent ignition key removal (if equipped) unless the shift lever is in P (Park) with the shift lever button fully released.


. Prevent movement of the shift


lever out of P (Park), unless the ignition is in ON/RUN and the brake pedal is applied.


The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9-volt) battery. If the vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting - North America 0 293. To shift out of P (Park): 1. Apply the brake pedal. 2. Place the ignition in ON/RUN. 3. Press the shift lever button.


Driving and Operating


195


4. Move the shift lever to the


desired position.


If still unable to shift out of P (Park): 1. Fully release the shift lever


button.


2. Hold the brake pedal down and


press the shift lever button again.


3. Move the shift lever to the


desired position.


If you are still having a problem shifting, see your dealer. Shift Lock Manual Release If jump starting the vehicle did not work, the shift lock manual release must be used. To access the shift lock manual release: 1. Apply the parking brake.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


196


Driving and Operating


2. Release the shift lever trim


from the center console at the rear, then fold upward and turn it to the left.


3.


4.


Insert a tool into the opening as far as it will go. At the same time move the shift lever out of P (Park). If P (Park) is selected again, the shift lever will be locked again. Have the cause of the problem fixed by your dealer. Install the shift lever trim on the console.


Parking over Things That Burn


{ Warning


Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn.


Engine Exhaust { Warning


Engine exhaust contains carbon monoxide (CO), which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if:


. The vehicle idles in areas


with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes).


. The exhaust smells or


sounds strange or different. . The exhaust system leaks


due to corrosion or damage. . The vehicle exhaust system


has been modified, damaged, or improperly repaired.


(Continued)


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Running the Vehicle While Parked It is better not to park with the engine running. If the vehicle is left with the engine running, follow the proper steps to be sure the vehicle will not move. See Shifting Into Park 0 194 and Engine Exhaust 0 196. If parking on a hill and pulling a trailer, see Driving Characteristics and Towing Tips 0 218.


Warning (Continued)


. There are holes or openings


in the vehicle body from damage or aftermarket modifications that are not completely sealed.


If unusual fumes are detected or if it is suspected that exhaust is coming into the vehicle:


. Drive it only with the


windows completely down. . Have the vehicle repaired


immediately.


Never park the vehicle with the engine running in an enclosed area such as a garage or a building that has no fresh air ventilation.


Driving and Operating


197


Automatic Transmission


P : This position locks the front wheels. It is the best position to use when you start the engine because the vehicle cannot move easily.


{ Warning


It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll.


(Continued)


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


198


Driving and Operating


Warning (Continued)


Caution


Warning (Continued)


Do not leave the vehicle when the engine is running. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park). See Shifting Into Park 0 194.


Make sure the shift lever is fully in P (Park) before starting the engine. The vehicle has an automatic transmission shift lock control system. You must fully apply the brake pedal then press the shift lever button before you can shift from P (Park) while the ignition key is in ON/RUN. If you cannot shift out of P (Park), ease pressure on the shift lever and push the shift lever all the way into P (Park) as you maintain brake application. Then move the shift lever into another gear. See Shifting out of Park 0 195. R : Use this gear to back up.


Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.


To rock the vehicle back and forth to get out of snow, ice, or sand without damaging the transmission, see If the Vehicle Is Stuck 0 183. N : In this position, the engine does not connect with the wheels. To restart the engine when the vehicle is already moving, use N (Neutral) only.


{ Warning


Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is firmly on the brake pedal, the vehicle could move very rapidly.


(Continued)


You could lose control and hit people or objects. Do not shift into a drive gear while the engine is running at high speed.


Caution


Shifting out of P (Park) or N (Neutral) with the engine running at high speed may damage the transmission. The repairs would not be covered by the vehicle warranty. Be sure the engine is not running at high speed when shifting the vehicle.


D : This position is for normal driving. It provides the best fuel economy. If you need more power for passing, and you are: . Accelerating slowly or


maintaining a constant speed, push the accelerator pedal about halfway down.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


. Accelerating quickly or passing,


push the accelerator all the way down.


M : This position allows you to change gears similar to a manual transmission. If the vehicle has this feature, see Manual Mode 0 199.


Manual Mode


Driver Shift Control (DSC) To use this feature: 1. Move the shift lever from


D (Drive) rearward to M (Manual). While driving in manual mode, the transmission will remain in the driver selected gear. When coming to a stop in the manual position, the vehicle will automatically shift into 1 (First) gear.


2. Press the + (plus) end of the button on the top of the shift lever to upshift, or press the − (minus) end of the button to downshift.


The Driver Information Center (DIC) in the instrument cluster will change from the currently displayed message to the letter “M,” for Manual position, and a number indicating the requested gear. While using the DSC feature the transmission will have firmer shifting and sportier performance. You can use this for sport driving or when climbing hills to stay in gear longer or to downshift for more power or engine braking. The transmission will only allow you to shift into gears appropriate for the vehicle speed and engine revolutions per minute (rpm): . The transmission will not allow


shifting to the next higher gear if the vehicle speed or engine rpm is too low.


. The transmission will not allow shifting to the next lower gear if the vehicle speed or engine rpm is too high.


Driving and Operating


199


Second Gear Start Feature When accelerating the vehicle from a stop in snowy and icy conditions, you may want to shift into 2 (Second) gear. A higher gear allows you to gain more traction on slippery surfaces. With the DSC feature, the vehicle can be set to pull away in 2 (Second) gear. 1. Move the shift lever from


D (Drive) to M (Manual Mode).


2. With the vehicle stopped, press


the (+) end of the button to select 2 (Second) gear. The vehicle will start from a stop position in 2 (Second) gear.


3. Once moving, select the


desired drive gear.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


200


Driving and Operating


Brakes


Antilock Brake System (ABS) This vehicle has ABS, an advanced electronic braking system that helps prevent a braking skid. When the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little. This is normal.


If there is a problem with ABS, this warning light stays on. See Antilock Brake System (ABS) Warning Light 0 108. If driving safely on a wet road and it becomes necessary to slam on the brakes and continue braking to


avoid a sudden obstacle, a computer senses the wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel. ABS can change the brake pressure to each wheel, as required, faster than any driver could. This can help you steer around the obstacle while braking hard. As the brakes are applied, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS.


Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let ABS work. You may hear the ABS pump or motor operating and feel the brake pedal pulsate. This is normal. Braking in Emergencies ABS allows you to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking.


Parking Brake


Driving and Operating


201


transition from releasing the brake pedal to accelerating to drive off on a grade, HSA holds the braking pressure to prevent rolling. HSA will not activate if the vehicle is in a drive gear and facing downhill or if the vehicle is facing uphill and in R (Reverse).


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


To set the parking brake, hold the brake pedal down and pull up on the parking brake lever. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light 0 107. To release the parking brake, hold the brake pedal down. Pull the parking brake lever up until you can press the release button. Hold the release button in as you move the brake lever all the way down.


Caution


Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving.


Brake Assist The Brake Assist feature is designed to assist the driver in stopping or decreasing vehicle speed in emergency driving


conditions. This feature uses the stability system hydraulic brake control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the vehicle. The stability system hydraulic brake control module increases brake pressure at each corner of the vehicle until the ABS activates. Minor brake pedal pulsation or pedal movement during this time is normal and the driver should continue to apply the brake pedal as the driving situation dictates. The Brake Assist feature will automatically disengage when the brake pedal is released or brake pedal pressure is quickly decreased.


Hill Start Assist (HSA) If equipped, HSA may automatically activate when the vehicle is stopped on a grade. This feature is designed to prevent the vehicle from rolling, either forward or rearward, during vehicle drive off. During the


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


202


Driving and Operating


Ride Control Systems


Traction Control/ Electronic Stability Control


System Operation The vehicle has a Traction Control System (TCS) and StabiliTrak®, an electronic stability control system. These systems help limit wheel slip and assist the driver in maintaining control, especially on slippery road conditions. TCS activates if it senses that any of the drive wheels are spinning or beginning to lose traction. When this happens, TCS applies the brakes to the spinning wheels and reduces engine power to limit wheel spin. StabiliTrak activates when the vehicle senses a difference between the intended path and the direction the vehicle is actually traveling. StabiliTrak selectively applies braking pressure to any one of the


vehicle wheel brakes to assist the driver in keeping the vehicle on the intended path. If cruise control is being used and traction control or StabiliTrak begins to limit wheel spin, cruise control will disengage. Cruise control may be turned back on when road conditions allow. Both systems come on automatically when the vehicle is started and begins to move. The systems may be heard or felt while they are operating or while performing diagnostic checks. This is normal and does not mean there is a problem with the vehicle. It is recommended to leave both systems on for normal driving conditions, but it may be necessary to turn TCS off if the vehicle gets stuck in sand, mud, ice, or snow. See If the Vehicle Is Stuck 0 183
and “Turning the Systems Off and On” later in this section.


The indicator light for both systems is in the instrument cluster. This light will: . Flash when TCS is limiting


wheel spin.


. Flash when StabiliTrak is


activated.


. Turn on and stay on when either


system is not working.


If either system fails to turn on or to activate, a message displays in the Driver Information Center (DIC), and d comes on and stays on to indicate that the system is inactive and is not assisting the driver in maintaining control. The vehicle is safe to drive, but driving should be adjusted accordingly. If d comes on and stays on: 1. Stop the vehicle.


Driving and Operating


203


To turn TCS and StabiliTrak on again, press and release the TCS/ StabiliTrak button. The traction off light i and StabiliTrak OFF light g in the instrument cluster turn off. Adding accessories can affect the vehicle performance. See Accessories and Modifications 0 226.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


2. Turn the engine off and wait


15 seconds.


3. Start the engine. Drive the vehicle. If d comes on and stays on, the vehicle may need more time to diagnose the problem. If the condition persists, see your dealer. Turning the Systems Off and On


To turn the system off, press the TCS/StabiliTrak button.


Caution


Do not repeatedly brake or accelerate heavily when TCS is off. The vehicle driveline could be damaged.


To turn off only TCS, press and release the TCS/StabiliTrak button. The traction off light i displays in the instrument cluster. To turn TCS on again, press and release the TCS/StabiliTrak button. The traction off light i displayed in the instrument cluster will turn off. If TCS is limiting wheel spin when the TCS/StabiliTrak button is pressed, the system will not turn off until the wheels stop spinning. To turn off both TCS and StabiliTrak, press and hold the TCS/StabiliTrak button until the traction off light i and StabiliTrak OFF light g come on and stay on in the instrument cluster.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


204


Driving and Operating


Cruise Control With cruise control, you can maintain a speed of about 40 km/h (25 mph) or more without keeping your foot on the accelerator. Cruise control does not work at speeds below 40 km/h (25 mph). { Warning


Cruise control can be dangerous where you cannot drive safely at a steady speed. Do not use cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.


With the Traction Control System (TCS) or StabiliTrak system, the system may begin to limit wheel spin while you are using cruise control. If this happens, the cruise control will automatically disengage.


See Traction Control/Electronic Stability Control 0 202. If a collision alert occurs when cruise control is activated, cruise control is disengaged. See Forward Collision Alert (FCA) System 0 210. When road conditions allow you to safely use it again, cruise control can be turned back on. If the brakes are applied, cruise control disengages.


1 (On/Off) : Press to turn the cruise control on or off. A white indicator comes on in the instrument cluster when cruise is turned on.


* (Cancel) : Press to disengage cruise control without erasing the set speed from memory. RES/+ (Resume/Accelerate) : If there is a set speed in memory, press the control up briefly to resume to that speed or hold to accelerate. If cruise control is already active, use to increase vehicle speed. SET/− (Set/Coast) : Press the control down briefly to set the speed and activate cruise control. If cruise control is already active, use to decrease speed.


Setting Cruise Control If the 1 button is on when not in use, SET/− or RES/+ could get bumped and the vehicle could go into cruise when not desired. Keep the 1 button off when cruise is not being used. 1. Press 1 to turn the cruise


system on.


2. Get up to the speed desired.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


3. Move the control toward SET/−


. To increase the speed in small


and release it.


4. Remove foot from the


accelerator.


The cruise control indicator on the instrument cluster turns green after cruise control has been set to the desired speed. See Instrument Cluster 0 101.


Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied or * is pressed, the cruise control is disengaged without erasing the set speed from memory. Once the vehicle speed is about 40 km/h (25 mph) or more, press RES/+ up briefly and then release it. The vehicle returns to the previously set speed.


Increasing Speed While Using Cruise Control If the cruise control system is already activated: . Press and hold RES/+ up until the vehicle accelerates to the desired speed, then release it.


increments, press RES/+ up briefly. For each press, the vehicle goes about 1.6 km/h (1 mph) faster.


The speedometer reading can be displayed in either English or metric units. See Instrument Cluster 0 101. The increment value used depends on the units displayed.


Reducing Speed While Using Cruise Control If the cruise control system is already activated: . Press and hold SET/− down until


the desired lower speed is reached, then release it.


. To decrease the vehicle speed in


small increments, press SET/− down briefly. For each press, the vehicle goes about 1.6 km/h (1 mph) slower.


The speedometer reading can be displayed in either English or metric units. See Instrument Cluster 0 101. The increment value used depends on the units displayed.


Driving and Operating


205


Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle slows down to the previously set cruise control speed. While pressing the accelerator pedal or shortly following the release to override cruise control, briefly pressing SET– down will result in cruise control set to the current vehicle speed.


Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain your speed. When going downhill, you might have to brake or shift to a lower gear to keep your speed down. If the brake pedal is applied, cruise control will disengage.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


206


Driving and Operating


Ending Cruise Control There are four ways to end cruise control: . Step lightly on the brake pedal. . Press *. . Shift the transmission to


N (Neutral).


. To turn off the cruise control,


press 1.


Erasing Speed Memory The cruise control set speed is erased from memory if 1 is pressed or if the vehicle is turned off.


Driver Assistance Systems


Rear Vision Camera (RVC) The vehicle may have an RVC system. Read this entire section before using it. The RVC system can assist the driver when backing up by displaying a view of the area behind the vehicle.


{ Warning


The camera(s) do not display children, pedestrians, bicyclists, crossing traffic, animals, or any other object outside of the cameras’ field of view, below the bumper, or under the vehicle. Shown distances may be different from actual distances. Do not drive or park the vehicle using only these camera(s). Always check behind and around the


(Continued)


Warning (Continued)


vehicle before driving. Failure to use proper care may result in injury, death, or vehicle damage.


How the System Works When the vehicle is shifted into R (Reverse), the image of the area behind the vehicle appears in the radio screen. The previous screen displays when the vehicle is shifted out of R (Reverse) after approximately 10 seconds. To see the previous screen sooner, do one of the following: . Press a button on the infotainment system.


. Shift into P (Park). . Reach a vehicle speed of


8 km/h (5 mph).


Press MENU to adjust the display brightness while viewing the rear camera display.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Symbols and Guidelines The system may have a feature that lets the driver view caution symbols on the infotainment screen while using the RVC. The Rear Parking Assist (RPA) system must not be disabled to use the caution symbols. The error message Rear Parking Assist Symbols Unavailable may display if RPA has been disabled and the symbols have been turned on. The symbols appear and may cover an object when viewing the infotainment screen when an object is detected by the RPA system. The RVC system may have a guideline overlay that can help the driver align the vehicle when backing into a parking spot. To turn the symbols and guidelines on or off: 1. Shift into P (Park). 2. Press the CONFIG button on


the infotainment system.


3. Select Display Settings and then Rear Camera Options.


4. Select Symbols or Guidelines.


When a checkmark appears next to the option, the feature is on.


Rear Cross Traffic Alert (RCTA) On vehicles with the RCTA, when shifted into R (Reverse), a warning triangle with a left or right pointing arrow may display on the RVC screen to warn of traffic coming from the left or the right. Three beeps will also sound from the left or right side, depending on the approaching cross traffic direction. This system detects objects coming from up to 20 m (65 ft) from the left or right side behind the vehicle. The RCTA system will not work properly if ice, snow, mud, or anything else builds up on the rear bumper sensors. Use caution while backing up when towing a trailer, as the RCTA detection zones that extend out from the back of your vehicle do not move further back when a trailer is towed. To turn RCTA on or off, see “Collision Detection Systems” under Vehicle Personalization 0 122.


Driving and Operating


207


Rear Vision Camera Error Messages SERVICE REAR VISION CAMERA SYSTEM : If this message appears in the center stack display, the system may need service. If any other problem occurs or if a problem persists, see your dealer. Rear Vision Camera Location


The RVC is above the license plate. The area displayed by the camera is limited. It does not display objects that are close to either corner or under the bumper and can vary depending on


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


208


Driving and Operating


vehicle orientation or road conditions. Displayed images may be farther or closer than they appear. The following illustrations show the field of view that the camera provides.


1. View displayed by the


camera.


2. Corner of the rear bumper.


When the System Does Not Seem To Work Properly The RVC system may not work properly or display a clear image if: . The sun or the beam of


It is dark.


headlamps is shining directly into the camera lens. Ice, snow, mud, or anything else has built up on the camera lens. Clean the lens, rinse it with water, and wipe it with a soft cloth.


1. View displayed by the


camera.


. The back of the vehicle was in an accident. The position and mounting angle of the camera can change or the camera can be affected. Be sure to have the camera and its position and mounting angle checked at your dealer.


Parking Assist If equipped, the Rear Parking Assist (RPA) system assists the driver with parking and avoiding objects while in R (Reverse). RPA operates at speeds less than 8 km/h (5 mph). The sensors on the rear bumper detect objects up to 2.5 m (8 ft) behind the vehicle, and at least 20 cm (8 in) off the ground. The distance objects can be detected may be less during warmer or humid weather.


{ Warning


The parking assist system does not detect children, pedestrians, bicyclists, animals, or objects


(Continued)


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Warning (Continued)


below the bumper or that are too close or too far from the vehicle. It is not available at speeds greater than 8 km/h (5 mph). To prevent injury, death, or vehicle damage, even with parking assist, always check the area around the vehicle and check all mirrors before backing.


How the System Works RPA comes on automatically when the shift lever is moved into R (Reverse). A single beep sounds to indicate the system is working. An obstacle detection is indicated by beeps. The time between the beeps becomes shorter as the vehicle gets closer to the obstacle. When the distance is less than 30 cm (12 in), the beeping is a continuous beep for five seconds.


Turning the System On and Off The RPA system can be turned on and off using the infotainment system controls. See Vehicle Personalization 0 122. When the system is off, PARK ASSIST OFF displays on the Driver Information Center (DIC). The message disappears after a short period of time. RPA defaults to the on setting each time the vehicle is started. Turn off RPA when towing a trailer. When the System Does Not Seem to Work Properly The following messages may be displayed on the DIC: SERVICE PARKING ASSIST : If this message occurs, check the following conditions: . The sensors are not clean. Keep the vehicle's rear bumper free of mud, dirt, snow, ice, and slush. For cleaning instructions, see Exterior Care 0 298.


Driving and Operating


209


. The parking assist sensors are covered by frost or ice. Frost or ice can form around and behind the sensors and may not always be seen; this can occur after washing the vehicle in cold weather. The message may not clear until the frost or ice has melted.


If the above conditions do not exist, take the vehicle to your dealer to repair the system. PARK ASSIST OFF : If the RPA system does not activate due to a temporary condition, the message displays on the DIC. This can occur under the following conditions: . The driver has disabled the


system.


. An object was hanging out of the trunk during the last drive cycle. Once the object is removed, RPA will return to normal operation.


. The bumper is damaged. Take


the vehicle to your dealer to repair the system.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


210


Driving and Operating


. Other conditions, such as


vibrations from a jackhammer or the compression of air brakes on a very large truck, are affecting system performance.


Forward Collision Alert (FCA) System If equipped, the FCA system may help to avoid or reduce the harm caused by front-end crashes. When approaching a vehicle ahead too quickly, FCA provides a flashing red alert on the windshield, and rapidly beeps. FCA also lights an amber visual alert if following another vehicle much too closely. FCA detects vehicles within a distance of approximately 60 m (197 ft) and operates at speeds above 40 km/h (25 mph). { Warning


FCA is a warning system and does not apply the brakes. When approaching a slower-moving or


(Continued)


Warning (Continued)


stopped vehicle ahead too rapidly, or when following a vehicle too closely, FCA may not provide a warning with enough time to help avoid a crash. FCA does not warn of pedestrians, animals, signs, guardrails, bridges, construction barrels, or other objects. Be ready to take action and apply the brakes. For more information, see Defensive Driving 0 177.


FCA can be disabled with the FCA steering wheel control. Detecting the Vehicle Ahead


FCA warnings will not occur unless the FCA system detects a vehicle ahead. When a vehicle is detected, the vehicle ahead indicator will


display green. Vehicles may not be detected on curves, highway exit ramps, or hills, due to poor visibility; or if a vehicle ahead is partially blocked by pedestrians or other objects. FCA will not detect another vehicle ahead until it is completely in the driving lane.


{ Warning


FCA does not provide a warning to help avoid a crash, unless it detects a vehicle. FCA may not detect a vehicle ahead if the FCA sensor is blocked by dirt, snow, or ice, or if the windshield is damaged. It may also not detect a vehicle on winding or hilly roads, or in conditions that can limit visibility such as fog, rain, or snow, or if the headlamps or windshield are not cleaned or in proper condition. Keep the windshield, headlamps, and FCA sensors clean and in good repair.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Collision Alert


Tailgating Alert


When your vehicle approaches another detected vehicle too rapidly, the red FCA display will flash on the windshield. Also, eight rapid high-pitched beeps will sound from the front. When this Collision Alert occurs, the brake system may prepare for driver braking to occur more rapidly which can cause a brief, mild deceleration. Continue to apply the brake pedal as the driving situation dictates. Cruise control may be disengaged when the Collision Alert occurs.


The vehicle ahead indicator will display amber when you are following a detected vehicle ahead much too closely. Selecting the Alert Timing The Collision Alert control is on the steering wheel. Press [ to set the FCA timing to far, medium, near, or off. The first button press shows the current control setting on the DIC. Additional button presses will change this setting. The chosen setting will remain until it is changed and will affect the timing of both the Collision Alert and the Tailgating Alert features. The timing of both alerts will vary based on vehicle speed. The faster the vehicle speed, the farther away the alert will occur. Consider traffic and weather conditions when selecting the alert


Driving and Operating


211


timing. The range of selectable alert timing may not be appropriate for all drivers and driving conditions. Unnecessary Alerts FCA may provide unnecessary alerts to turning vehicles, vehicles in other lanes, objects that are not vehicles, or shadows. These alerts are normal operation and the vehicle does not need service. Cleaning the System If the FCA system does not seem to operate properly, cleaning the outside of the windshield in front of the camera sensor may correct the issue


Side Blind Zone Alert (SBZA) If equipped, the SBZA system is a lane-changing aid that assists drivers with avoiding crashes that occur with moving vehicles in the side blind zone (or spot) areas. The SBZA warning display will light up in


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


212


Driving and Operating


the corresponding outside side mirror and will flash if the turn signal is on.


{ Warning


SBZA does not alert the driver to vehicles rapidly approaching outside of the side blind zones, pedestrians, bicyclists, or animals. It may not provide alerts when changing lanes under all driving conditions. Failure to use proper care when changing lanes may result in injury, death, or vehicle damage. Before making a lane change, always check mirrors, glance over your shoulder, and use the turn signals.


SBZA Detection Zones


unsafe to change lanes. Before making a lane change, check the SBZA display, check mirrors, glance over your shoulder, and use the turn signals.


The SBZA sensor covers a zone of approximately one lane over from both sides of the vehicle, or 3.5 m (11 ft). The height of the zone is approximately between 0.5 m (1.5 ft) and 2 m (6 ft) off the ground. This zone starts at approximately the middle of the vehicle and goes back 5 m (16 ft). How the System Works The SBZA symbol lights up in the side mirrors when the system detects a moving vehicle in the next lane over that is in the side blind zone. This indicates it may be


Left Side Mirror


Right Side Mirror


Display


Display


When the vehicle is started, both outside mirror SBZA displays will briefly come on to indicate the system is operating. When the vehicle is in a forward gear, the left or right side mirror display will light up if a moving vehicle is detected in that blind zone. If the turn signal is activated in the same direction of a detected vehicle, this display will flash as an extra warning not to change lanes. SBZA can be disabled through vehicle personalization. See “Collision Detection Systems” under Vehicle Personalization 0 122.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


If SBZA is disabled by the driver, the SBZA mirror displays will not light up. When the System Does Not Seem to Work Properly SBZA displays may not come on when passing a vehicle quickly, for a stopped vehicle, or when towing a trailer. The SBZA detection zones that extend back from the side of the vehicle do not move further back when a trailer is towed. Use caution while changing lanes when towing a trailer. SBZA may alert to objects attached to the vehicle, such as a trailer, bicycle, or object extending out to either side of the vehicle. This is normal system operation; the vehicle does not need service. SBZA may not always alert the driver to vehicles in the side blind zone, especially in wet conditions. The system does not need to be serviced. The system may light up due to guardrails, signs, trees, shrubs, and other non-moving objects. This is normal system operation; the vehicle does not need service.


SBZA may not operate when the SBZA sensors in the left or right corners of the rear bumper are covered with mud, dirt, snow, ice, or slush, or in heavy rainstorms. For cleaning instructions, see "Washing the Vehicle" under Exterior Care 0 298. If the DIC displays the system unavailable message after cleaning both sides of the vehicle toward the rear corners of the vehicle, see your dealer. If the SBZA displays do not light up when vehicles are in the blind zone and the system is clean, the system may need service. Take the vehicle to your dealer. When SBZA is disabled for any reason other than the driver turning it off, the Side Blind Zone Alert On option will not be available on the personalization menu. Radio Frequency Information See Radio Frequency Statement 0 335.


Driving and Operating


213


Lane Departure Warning (LDW) If equipped, LDW may help avoid crashes due to unintentional lane departures. It may provide an alert if the vehicle is crossing a lane without using a turn signal in that direction. LDW uses a camera sensor to detect the lane markings at speeds of 56 km/h (35 mph) or greater.


{ Warning


The LDW system does not steer the vehicle. The LDW system may not:


. Provide enough time to


avoid a crash.


. Detect lane markings under


poor weather or visibility conditions. This can occur if the windshield or headlamps are blocked by dirt, snow, or ice; if they are


(Continued)


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


214


Driving and Operating


Warning (Continued)


not in proper condition; or if the sun shines directly into the camera.


. Detect road edges. . Detect lanes on winding or


hilly roads.


If LDW only detects lane markings on one side of the road, it will only warn you when departing the lane on the side where it has detected a lane marking. Always keep your attention on the road and maintain proper vehicle position within the lane, or vehicle damage, injury, or death could occur. Always keep the windshield, headlamps, and camera sensors clean and in good repair. Do not use LDW in bad weather conditions.


How the System Works The LDW camera sensor is on the windshield ahead of the rearview mirror. To turn LDW on and off, press @ on the center stack, forward of the shift lever. The control indicator will light when LDW is on.


When LDW is on, @ is green if LDW is available to warn of a lane departure. If the vehicle crosses a detected lane marking without using the turn signal in that direction, @ changes to amber and flashes. Additionally, there will be three beeps on the right or left, depending on the lane departure direction.


When the System Does Not Seem to Work Properly The system may not detect lanes as well when there are: . Close vehicles ahead. . Sudden lighting changes, such


as when driving through tunnels.


. Banked roads. If the LDW system is not functioning properly when lane markings are clearly visible, cleaning the windshield may help. LDW alerts may occur due to tar marks, shadows, cracks in the road, temporary or construction lane markings, or other road imperfections. This is normal system operation; the vehicle does not need service. Turn LDW off if these conditions continue.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. When driving in the U.S. and Canada, to help keep the engine clean and maintain optimum vehicle performance, we recommend using TOP TIER Detergent Gasolines. See www.toptiergas.com for a list of TOP TIER Detergent Gasolines.


Use regular unleaded gasoline meeting ASTM specification D4814
with a posted octane rating of 87 or higher. Do not use gasoline with an


Driving and Operating


215


Caution


Do not use fuel containing methanol. It can corrode metal parts in the fuel system and also damage plastic and rubber parts. That damage would not be covered under the vehicle warranty.


Some gasolines, mainly high octane racing gasolines, can contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). Do not use gasolines and/or fuel additives with MMT as they can reduce spark plug life and affect emission control system performance. The malfunction indicator lamp may turn on. If this occurs, see your dealer for service.


octane rating below 87, as it may cause engine damage and will lower fuel economy.


Use of Seasonal Fuels Use summer and winter fuels in the appropriate season. The fuels industry automatically modifies the fuel for the appropriate season. If fuel is left in the vehicle tank for long periods of time, driving or starting could be affected. Drive the vehicle until the fuel is at one-half tank or less, then refuel with the current seasonal fuel.


Prohibited Fuels Gasolines containing oxygenates such as ethers and ethanol, as well as reformulated gasolines, are available in some cities. If these gasolines comply with the previously described specification, then they are acceptable to use. However, E85 (85% ethanol) and other fuels containing more than 15% ethanol must be used only in FlexFuel vehicles.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


216


Driving and Operating


California Fuel Requirements If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California Emissions Standards, the vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance might be affected. The malfunction indicator lamp could turn on and the vehicle may not pass a smog-check test. See Malfunction Indicator Lamp (Check Engine Light) 0 106. If this occurs, return to your authorized dealer for diagnosis. If it is determined that the condition is caused by the type of fuel used, repairs may not be covered by the vehicle warranty.


Fuels in Foreign Countries If planning to drive in countries outside the U.S. or Canada, the proper fuel might be hard to find. Check regional auto club or fuel retail brand websites for availability in the country where driving. Never use leaded gasoline, fuel containing methanol, manganese, or any other fuel not recommended. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty.


Fuel Additives To keep fuel systems clean, TOP TIER Detergent Gasoline is recommended. See Fuel 0 215. If TOP TIER Detergent Gasoline is not available, one bottle of Fuel System Treatment PLUS added to the fuel tank at every engine oil change, can help. Fuel System Treatment PLUS is the only gasoline additive recommended by General Motors. It is available at your dealer.


Filling the Tank


{ Warning


Fuel vapors and fuel fires burn violently and can cause injury or death.


. To help avoid injuries to you and others, read and follow all the instructions on the fuel pump island.


. Turn off the engine when


refueling.


. Keep sparks, flames, and


smoking materials away from fuel.


. Do not leave the fuel pump


unattended.


. Do not use a cell phone


while refueling.


. Do not reenter the vehicle


while pumping fuel.


. Keep children away from


the fuel pump and never let children pump fuel.


(Continued)


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Warning (Continued)


. Fuel can spray out if the fuel


cap is opened too quickly. This spray can happen if the tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop, then unscrew the cap all the way.


The fuel cap is behind a hinged fuel door on the passenger side of the vehicle. To open the fuel door, push and release the rearward center edge of the door. Turn the fuel cap counterclockwise to remove. While refueling, hang the fuel cap from the hook on the fuel door. Reinstall the cap by turning it clockwise until it clicks.


{ Warning


Overfilling the fuel tank by more than three clicks of a standard fill nozzle may cause:


. Vehicle performance issues, including engine stalling and damage to the fuel system.


. Fuel spills. . Potential fuel fires.


Be careful not to spill fuel. Wait a few seconds after you have finished pumping before removing the nozzle. Clean fuel from painted surfaces as soon as possible. See Exterior Care 0 298.


Driving and Operating


217


When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp (Check Engine Light) 0 106.


{ Warning


If a fire starts while you are refueling, do not remove the nozzle. Shut off the flow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately.


Caution


If a new fuel cap is needed, be sure to get the right type of cap from your dealer. The wrong type of fuel cap may not fit properly, may cause the malfunction


(Continued)


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


218


Driving and Operating


Caution (Continued)


Warning (Continued)


. Place the container on the


ground.


. Place the nozzle inside the fill opening of the container before dispensing fuel, and keep it in contact with the fill opening until filling is complete.


. Fill the container no more than 95% full to allow for expansion.


. Do not smoke, light


matches, or use lighters while pumping fuel.


. Avoid using cell phones or


other electronic devices.


indicator lamp to light, and could damage the fuel tank and emissions system. See Malfunction Indicator Lamp (Check Engine Light) 0 106.


Filling a Portable Fuel Container


{ Warning


Filling a portable fuel container while it is in the vehicle can cause fuel vapors that can ignite either by static electricity or other means. You or others could be badly burned and the vehicle could be damaged. Always:


. Use approved fuel


containers.


. Remove the container from the vehicle, trunk, or pickup bed before filling.


(Continued)


Trailer Towing


General Towing Information Only use towing equipment that has been designed for the vehicle. Contact your dealer or trailering dealer for assistance with preparing the vehicle for towing a trailer. Read the entire section before towing a trailer. For towing a disabled vehicle, see Towing the Vehicle 0 296. For towing the vehicle behind another vehicle such as a motor home, see Recreational Vehicle Towing 0 296.


Driving Characteristics and Towing Tips


Driving with a Trailer When towing a trailer: . Become familiar with the state


and local laws that apply specifically to trailer towing.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


. Do not tow a trailer during the


first 800 km (500 mi), to prevent damage to the engine, axle, or other parts.


. Then, during the first 800 km


(500 mi) of trailer towing, do not drive over 80 km/h (50 mph) and do not make starts at full throttle. . The vehicle can tow in D (Drive)


but M (Manual Mode) is recommended. See Manual Mode 0 199. Use a lower gear if the transmission shifts too often.


. Turn off Park Assist when


towing.


{ Warning


When towing a trailer, exhaust gases may collect at the rear of the vehicle and enter if the liftgate, trunk/hatch, or rear-most window is open. When towing a trailer:


(Continued)


Warning (Continued)


. Do not drive with the liftgate, trunk/hatch, or rear-most window open. . Fully open the air outlets on


or under the instrument panel.


. Also adjust the Climate


Control system to a setting that brings in only outside air. See “Climate Control Systems” in the Index. For information about carbon monoxide, see Engine Exhaust 0 196.


Towing a trailer requires a certain amount of experience. The combination you are driving is longer and not as responsive as the vehicle itself. Get acquainted with the handling and braking of the rig before setting out for the open road. Before starting, check all trailer hitch parts and attachments, safety chains, electrical connectors, lamps, tires, and mirrors. If the trailer has


Driving and Operating


219


electric brakes, start the combination moving and then apply the trailer brake controller by hand to be sure the brakes work. During the trip, check occasionally to be sure that the load is secure and the lamps and any trailer brakes still work. Towing with a Stability Control System When towing, the sound of the stability control system might be heard. The system is reacting to the vehicle movement caused by the trailer, which mainly occurs during cornering. This is normal when towing heavier trailers. Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer. This can help to avoid situations that require heavy braking and sudden turns.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


220


Driving and Operating


Passing More passing distance is needed when towing a trailer. Because the rig is longer, it is necessary to go farther beyond the passed vehicle before returning to the lane. Backing Up Hold the bottom of the steering wheel with one hand. To move the trailer to the left, move your hand to the left. To move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you. Making Turns


Caution


Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle. The vehicle could be damaged. Avoid making very sharp turns while trailering.


When turning with a trailer, make wider turns than normal so the trailer will not strike soft shoulders, curbs, road signs, trees, or other objects. Use the turn signal well in advance and avoid jerky or sudden maneuvers. Turn Signals When Towing a Trailer The turn signal indicators on the instrument cluster flash whenever signaling a turn or lane change. Properly hooked up, the trailer lamps also flash, telling other drivers the vehicle is turning, changing lanes, or stopping. When towing a trailer, the arrows on the instrument cluster flash for turns even if the bulbs on the trailer are burned out. Check occasionally to be sure the trailer bulbs are still working. Driving on Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the


brakes might have to be used so much that they would get hot and no longer work well. The vehicle can tow in D (Drive). Use a lower gear if the transmission shifts too often. When towing at high altitude on steep uphill grades, engine coolant boils at a lower temperature than at normal altitudes. If the engine is turned off immediately after towing at high altitude on steep uphill grades, the vehicle could show signs similar to engine overheating. To avoid this, let the engine run while parked, preferably on level ground, with the transmission in P (Park) for a few minutes before turning the engine off. If the overheat warning comes on, see Engine Overheating 0 238.


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


Parking on Hills


{ Warning


Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.


If parking the rig on a hill: 1. Press the brake pedal, but do not shift into P (Park) yet. Turn the wheels into the curb if facing downhill or into traffic if facing uphill.


2. Have someone place chocks


under the trailer wheels.


3. When the wheel chocks are in place, release the brake pedal until the chocks absorb the load.


4. Reapply the brake pedal. Then


apply the parking brake and shift into P (Park).


5. Release the brake pedal. Leaving After Parking on a Hill 1. Apply and hold the brake pedal


while you: 1.1. Start the engine. 1.2. Shift into a gear. 1.3. Release the parking


brake.


2. Let up on the brake pedal. 3. Drive slowly until the trailer is


clear of the chocks.


4. Stop and have someone pick


up and store the chocks. Maintenance When Trailer Towing The vehicle needs service more often when pulling a trailer. See the Maintenance Schedule 0 309. Things that are especially important in trailer operation are automatic transmission fluid, engine oil, axle lubricant, belts, cooling system, and brake system. Inspect these before and during the trip.


Driving and Operating


221


Check periodically to see that all hitch nuts and bolts are tight. Engine Cooling When Trailer Towing The cooling system may temporarily overheat during severe operating conditions. See Engine Overheating 0 238.


Trailer Towing Before pulling a trailer, three important considerations have to do with weight: . Weight of the trailer. . Weight of the trailer tongue. . Total weight on your vehicle's


tires.


Weight of the Trailer How heavy can a trailer safely be? It should never weigh more than 454 kg (1,000 lb). But even that can be too heavy. It depends on how the rig is used. For example, speed, altitude, road grades, outside temperature, and


Chevrolet Malibu Limited Owner Manual (GMNA-Localizing-U.S/Canada- 9086425) - 2016 - crc - 7/30/15


222


Driving and Operating


how much the vehicle is used to pull a trailer are all important. It can depend on any special equipment on the vehicle, and the amount of tongue weight the vehicle can carry. See “Weight of the Trailer Tongue” following. Maximum trailer weight is calculated assuming the tow vehicle has the driver, a front seat passenger and all the required tow equipment. and it has all the required trailering equipment. The weight of additional optional equipment, passengers, and cargo in the tow vehicle must be subtracted from the maximum trailer weight. Ask your dealer for trailering information or advice, or write us at our Customer Assistance Offices. See Customer Assistance Offices 0 327. Weight of the Trailer Tongue The tongue load (1) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any


cargo carried in it, and the people who will be riding in the vehicle. If there are a lot of options, equipment, passengers, or cargo in the vehicle, it will reduce the tongue weight the vehicle can carry, which will also reduce the trailer weight the vehicle can tow. If towing a trailer, the tongue load must be added to the GVW because the vehicle will be carrying that weight, too. See Vehicle Load Limits 0 183.


The trailer tongue (1) should weigh 10 % of the total loaded trailer weight (2).


After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they are not, adjustments might be made by moving some items around in the trailer. Total Weight on Your Vehicle's Tires Be sure the vehicle's tires are inflated to the upper limit for cold tires. These numbers can be found on the Tire and Loading Information label. See Vehicle Load Limits 0 183. Make sure not to go over the GVW limit for the vehicle, including the weight of the trailer tongue.


Towing Equipment


Loading...
x