2011 Chevrolet Malibu Owners Manual

shifting to the next lower gear if the vehicle speed or engine RPM is too high.

Second or Third Gear Start Feature When accelerating the vehicle from a stop in snowy and icy conditions, you may want to shift the gear select tap switch into Second or Third gear. A higher gear allows you to gain more traction on slippery surfaces. With the DSC feature, the vehicle can be set to pull away in Second or Third gear. 1. Move the shift lever from

D (Drive) into the M (Manual Mode).

2. With the vehicle stopped,

press (+) end of the button to select Second or Third gear. The vehicle will start from a stop position in Second or Third gear. 3. Once moving select the desired

drive gear.

2. Press the + (plus) end of the

button on the side of the shifter to upshift, or push the − (minus) end of the button to downshift.

The Driver Information Center (DIC) in the instrument cluster will change from the currently displayed message to the letter “M”, for Manual position, and a number indicating the requested gear.

Chevrolet Malibu Owner Manual - 2011

Black plate (27,1)

Driving and Operating

9-27

Brakes

Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little. This is normal.

If there is a problem with ABS, this warning light stays on. See Antilock Brake System (ABS) Warning Light on page 5‑19.

If driving safely on a wet road and it becomes necessary to slam on the brakes and continue braking to avoid a sudden obstacle, a computer senses that the wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel. ABS can change the brake pressure to each wheel, as required, faster than any driver could. This can help the driver steer around the obstacle while braking hard. As the brakes are applied, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle

suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let ABS work. You might hear the ABS pump or motor operating and feel the brake pedal pulsate, but this is normal. Braking in Emergencies ABS allows the driver to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking.

Chevrolet Malibu Owner Manual - 2011

Black plate (28,1)

9-28

Driving and Operating

Parking Brake

To set the parking brake, push down the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 5‑18. To release the parking brake, hold the regular brake pedal down with your right foot. Push down momentarily on the parking brake pedal with your left foot until you feel the pedal release. If the parking brake is not released when you

begin to drive, the brake system warning light comes on and a chime sounds as a warning that the parking brake is still on. The PUSH PARK PEDAL message will also display in the Driver Information Center (DIC) as a reminder to release the parking brake. See Brake System Messages on page 5‑26. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and are parking on a hill, see Driving Characteristics and Towing Tips on page 9‑42.

Brake Assist This vehicle has a brake assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability system hydraulic brake control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the vehicle. The stability system hydraulic brake control module increases brake pressure at each corner of the vehicle until the ABS activates. Minor brake pedal pulsation or pedal movement during this time is normal and the driver should continue to apply the brake pedal as the driving situation dictates. The brake assist feature will automatically disengage when the brake pedal is released or brake pedal pressure is quickly decreased.

Chevrolet Malibu Owner Manual - 2011

Black plate (29,1)

Driving and Operating

9-29

Ride Control Systems

Traction Control System (TCS) The vehicle may have a Traction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that the front wheels are spinning too much or are beginning to lose traction. When this happens, the system works the front brakes and reduces engine power by closing the throttle and managing engine spark to limit wheel spin.

This light will flash when the traction control system is limiting wheel spin.

The system may be heard or felt while it is working, but this is normal. If the vehicle is in cruise control when TCS begins to limit wheel spin, the cruise control will automatically disengage. The cruise control may be re-engaged when road conditions allow. See Cruise Control on page 9‑32.

When this light is on solid and either the SERVICE TRACTION or TRACTION OFF message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See Ride Control System Messages on page 5‑27 for more information.

The Traction Control System is automatically enabled whenever the vehicle is started. To limit wheel spin, especially in slippery road conditions, always leave the system enabled. TCS can be turned off if needed. It is recommended to leave the system on for normal driving conditions, but it may be necessary to turn the system off if the vehicle is stuck in sand, mud, ice or snow, and you want to “rock” the vehicle to attempt to free it. It may also be necessary to turn off the system when driving in extreme off-road conditions where high wheel spin is required. See If the Vehicle is Stuck on page 9‑11.

Chevrolet Malibu Owner Manual - 2011

Black plate (30,1)

9-30

Driving and Operating

driving. For more information on the LOW TRACTION message, see Ride Control System Messages on page 5‑27. Notice: If the wheel(s) of one axle are allowed to spin excessively while the ESC/TCS, ABS and Brake warning lights and the SERVICE ESC and/or SERVICE TRACTION messages are displayed, the differential could be damaged. The repairs would not be covered by the vehicle warranty. Reduce engine power and do not spin the wheel(s) excessively while these lights and this message are displayed. Notice: When traction control is turned off, it is possible to lose traction. If you attempt to shift with the front wheels spinning with a loss of traction, it is possible to cause damage to the transmission. Do not attempt to shift when the front wheels do not have traction. Damage caused by

misuse of the vehicle is not covered. See your warranty book for additional information. The traction control system may activate on dry or rough roads or under conditions such as heavy acceleration while turning or abrupt upshifts/downshifts of the transmission. When this happens, a reduction in acceleration may be noticed, or a noise or vibration may be heard. This is normal. If the vehicle is in cruise control when the system activates, the ESC/TCS light will flash and the cruise control will automatically disengage. The cruise control may be re-engaged when road conditions allow. See Cruise Control on page 9‑32. Adding non‐dealer accessories can affect the vehicle's performance. See Accessories and Modifications on page 10‑3 for more information.

To turn the system off or on, press and release this button located on the center console. The DIC will display the appropriate message as described previously when the button is pressed. Traction Control Operation Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary. The traction control system is enabled automatically when the vehicle is started, and it will activate and flash the ESC/TCS light and display the LOW TRACTION message if it senses either of the front wheels are spinning or beginning to lose traction while

Chevrolet Malibu Owner Manual - 2011

Black plate (31,1)

Driving and Operating

9-31

Electronic Stability Control (ESC) The vehicle has an Electronic Stability Control (ESC) system which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions. When you first start the vehicle and begin to drive away, the system performs several diagnostic checks to ensure there are no problems. The system may be heard or felt while it is working. This is normal and does not mean there is a problem with the vehicle. The system should initialize before the vehicle reaches 32 km/h (20 mph). If the system fails to turn on or activate, the ESC/TCS light will be on solid, and the ESC OFF or SERVICE ESC message will be displayed.

For more information, see Ride Control System Messages on page 5‑27.

This light will flash on the instrument panel cluster when the ESC system is both on and activated. The system may be heard or felt while it is working; this is normal. When the light is on solid and either the SERVICE ESC or ESC OFF message is displayed, the system will not assist the driver in maintaining directional control of the vehicle. Adjust your driving accordingly. See Ride Control System Messages on page 5‑27.

The Electronic Stability Control (ESC) system is automatically enabled whenever the vehicle is started. To assist the driver with vehicle directional control, especially in slippery road conditions, the system should always be left on. But, ESC can be turned off if needed. If the vehicle is in cruise control when the system begins to assist the driver maintain directional control of the vehicle, the ESC/TCS light will flash and the cruise control will automatically disengage. The cruise control system may be re-engaged when road conditions allow. See Cruise Control on page 9‑32.

Chevrolet Malibu Owner Manual - 2011

Black plate (32,1)

9-32

Driving and Operating

when driving in extreme off-road conditions where high wheel spin is required. See If the Vehicle is Stuck on page 9‑11. ESC may also turn off automatically if it determines that a problem exists with the system. The ESC OFF and SERVICE ESC messages and the ESC/TCS light will be on solid to warn the driver that ESC is disabled and requires service. If the problem does not clear after restarting the vehicle, see your dealer for service. See Ride Control System Messages on page 5‑27 for more information. Adding non‐dealer accessories can affect the vehicle's performance. See Accessories and Modifications on page 10‑3 for more information.

Cruise Control Cruise control lets a speed of about 40 km/h (25 mph) or more be maintained without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below 40 km/h (25 mph). When the brakes are applied, the cruise control shuts off. If the vehicle is in cruise control and the Traction Control System (TCS) or Enhanced Traction System (ETS) begins to limit wheel spin, the cruise control automatically disengages. See Traction Control System (TCS) on page 9‑29 and Electronic Stability Control (ESC) on page 9‑31. When road conditions allow, the cruise control can be used again.

The ESC/TCS button is located on the instrument panel. The traction control system can be turned off or back on by pressing the ESC/TCS button. To disable both traction control and ESC, press and hold the button briefly. When the ESC system is turned off, the TRACTION OFF and ESC OFF messages will appear, and the ESC/ TCS light will be on solid to warn the driver that both traction control and ESC are disabled. It is recommended to leave the system on for normal driving conditions, but it may be necessary to turn the system off if the vehicle is stuck in sand, mud, ice or snow, and you want to “rock” the vehicle to attempt to free it. It may also be necessary to turn off the system

Chevrolet Malibu Owner Manual - 2011

Black plate (33,1)

{ WARNING

Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use the cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.

Driving and Operating

9-33

Setting Cruise Control If the cruise button is on when not in use, it could get bumped and go into cruise when not desired. Keep the cruise control switch off when cruise is not being used. 1. Press I to turn cruise control

on. The indicator light on the button comes on.

2. Get up to the desired speed. 3. Press the SET− and release it. The cruise symbol displays in the instrument panel cluster to show the system is engaged.

4. Take your foot off the accelerator

pedal.

The cruise control buttons are located on the steering wheel. I (On/Off): Press to turn the cruise control system on and off. RES+ (Resume): Press briefly to make the vehicle resume a previously set speed or press and hold to accelerate. SET− (Set): Press to set the speed and activate cruise control or make the vehicle decelerate.

Chevrolet Malibu Owner Manual - 2011

Black plate (34,1)

9-34

Driving and Operating

Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, the cruise control is disengaged without erasing the set speed from memory. The cruise symbol in the instrument panel cluster also goes out indicating cruise is no longer engaged. Once the vehicle speed is 40 km/h (25 mph) or greater, press the RES+ button on the steering wheel. The vehicle returns to the previously set speed and stays there.

Increasing Speed While Using Cruise Control If the cruise control system is already activated, . Press and hold the RES+ button

on the steering wheel until the desired speed is reached, then release it.

To increase the vehicle speed in small amounts, press the RES+ button briefly. Each time this is done, the vehicle goes about 1.6 km/h (1 mph) faster.

Reducing Speed While Using Cruise Control If the cruise control system is already activated, . Press and hold the SET− on the

steering wheel until the lower speed desired is reached, then release it. To slow down in small amounts, press the SET− button briefly. Each time this is done, the vehicle goes about 1.6 km/h (1 mph) slower.

Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the previously set cruise control speed.

Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle at a lower speed. When the brakes are applied this ends the cruise control.

Ending Cruise Control There are two ways to end cruise control:

To disengage the cruise control, step lightly on the brake pedal. To turn off cruise control, press the I button.

Erasing Speed Memory The cruise control set speed is erased from memory, by pressing the I button or if the ignition is turned off.

Chevrolet Malibu Owner Manual - 2011

Black plate (35,1)

Driving and Operating

9-35

Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. Look for the TOP TIER label on the fuel pump to ensure gasoline meets enhanced detergency standards developed by auto companies. A list of marketers providing TOP TIER Detergent Gasoline can be found at www.toptiergas.com.

use only the unleaded gasoline described under Recommended Fuel on page 9‑35.

Recommended Fuel If the vehicle has the 2.4L L4 engine (VIN Code 1) or the 2.4L L4 engine (VIN Code U), use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, an audible knocking noise, commonly referred to as spark knock, might be heard when driving. If this occurs, use a gasoline rated at 87 octane or higher as soon as possible. If heavy knocking is heard when using gasoline rated at 87 octane or higher, the engine needs service. If the vehicle has the 3.6L V6 engine (VIN Code 7), use regular unleaded gasoline with a posted octane rating of 87 or higher. For best performance or trailer towing, you could choose to use middle grade 89 octane unleaded gasoline. If the octane rating is less than 87, an

The eighth digit of the Vehicle Identification Number (VIN) shows the code letter or number that identifies the vehicle's engine. The VIN is at the top left of the instrument panel. See Vehicle Identification Number (VIN) on page 12‑1. Vehicles that have a FlexFuel badge and a yellow fuel cap can use either unleaded gasoline or ethanol fuel containing up to 85% ethanol (E85). See Fuel E85 (85% Ethanol) on page 9‑37. For all other vehicles,

Chevrolet Malibu Owner Manual - 2011

Black plate (36,1)

9-36

Driving and Operating

audible knocking noise, commonly referred to as spark knock, might be heard when driving. If this occurs, use a gasoline rated at 87 octane or higher as soon as possible. If heavy knocking is heard when using gasoline rated at 87 octane or higher, the engine needs service.

Gasoline Specifications (U.S. and Canada Only) At a minimum, gasoline should meet ASTM specification D 4814 in the United States or CAN/ CGSB‐3.5 or 3.511 in Canada. Some gasolines contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). We recommend against the use of gasolines containing MMT. See Fuel Additives on page 9‑36 for additional information.

California Fuel Requirements If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California Emissions Standards, the vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance might be affected. The malfunction indicator lamp could turn on and the vehicle might fail a smog‐check test. See Malfunction Indicator Lamp on page 5‑15. If this occurs, return to your authorized dealer for diagnosis. If it is determined that the condition is caused by the type of fuel used, repairs might not be covered by the vehicle warranty.

Fuels in Foreign Countries Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty. To check the fuel availability, ask an auto club, or contact a major oil company that does business in the country where you will be driving.

Fuel Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, nothing should have to be added to the fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S. Environmental Protection Agency

Chevrolet Malibu Owner Manual - 2011

Black plate (37,1)

regulations. To help keep fuel injectors and intake valves clean and avoid problems due to dirty injectors or valves, look for gasoline that is advertised as TOP TIER Detergent Gasoline. Look for the TOP TIER label on the fuel pump to ensure gasoline meets enhanced detergency standards developed by the auto companies. A list of marketers providing TOP TIER Detergent Gasoline can be found at www.toptiergas.com. For customers who do not use TOP TIER Detergent Gasoline regularly, one bottle of GM Fuel System Treatment PLUS, added to the fuel tank at every engine oil change, can help clean deposits from fuel injectors and intake valves. GM Fuel System Treatment PLUS is the only gasoline additive recommended by General Motors. It is available at your dealer.

Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the specifications described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels. Notice: This vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in the fuel system and also damage plastic and rubber parts. That damage would not be covered under the vehicle warranty. Some gasolines that are not reformulated for low emissions can contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask the attendant where you buy gasoline whether the

Driving and Operating

9-37

fuel contains MMT. We recommend against the use of such gasolines. Fuels containing MMT can reduce spark plug life and affect emission control system performance. The malfunction indicator lamp might turn on. If this occurs, return to your dealer for service.

Fuel E85 (85% Ethanol) Vehicles that have a FlexFuel badge and a yellow fuel cap can use either unleaded gasoline or ethanol fuel containing up to 85% ethanol (E85). For all other vehicles, use only the unleaded gasoline described under Recommended Fuel on page 9‑35. We encourage the use of E85 in vehicles that are designed to use it. The ethanol in E85 is a “renewable” fuel, meaning it is made from renewable sources such as corn and other crops.

Chevrolet Malibu Owner Manual - 2011

Black plate (38,1)

9-38

Driving and Operating

Many service stations will not have an 85% ethanol fuel (E85) pump available. The U.S. Department of Energy has an alternative fuels website (www.afdc.energy.gov/afdc/ locator/stations/) that can help you find E85 fuel. Those stations that do have E85 should have a label indicating ethanol content. Do not use the fuel if the ethanol content is greater than 85%. At a minimum, E85 should meet ASTM Specification D 5798. By definition, this means that fuel labeled E85 will have an ethanol content between 70% and 85%. Filling the fuel tank with fuel mixtures that do not meet ASTM specifications can affect driveability and could cause the malfunction indicator lamp to come on.

To ensure quick starts in the wintertime, the E85 fuel must be formulated properly for your climate according to ASTM specification D 5798. If you have trouble starting on E85, it could be because the E85
fuel is not properly formulated for your climate. If this happens, switching to gasoline or adding gasoline to the fuel tank can improve starting. For good starting and heater efficiency below 0°C (32°F), the fuel mix in the fuel tank should contain no more than 70% ethanol. It is best not to alternate repeatedly between gasoline and E85. If you do switch fuels, it is recommended that you add as much fuel as possible — do not add less than 11 L (3 gal) when refueling. You should drive the vehicle immediately after refueling for at least 11 km (7 mi) to allow the vehicle to adapt to the change in ethanol concentration.

E85 has less energy per liter (gallon) than gasoline, so you will need to refill the fuel tank more often when using E85 than when you are using gasoline. See Filling the Tank on page 9‑39. Notice: Some additives are not compatible with E85 fuel and can harm the vehicle's fuel system. Do not add anything to E85. Damage caused by additives would not be covered by the vehicle warranty. Notice: This vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in the fuel system and also damage plastic and rubber parts. That damage would not be covered under the vehicle warranty.

Chevrolet Malibu Owner Manual - 2011

Black plate (39,1)

Driving and Operating

9-39

Turn the tethered fuel cap counterclockwise to remove. If the vehicle has E85 fuel capability, the fuel cap will be yellow and state that E85 or gasoline can be used. See Fuel E85 (85% Ethanol) on page 9‑37. While refueling, hang the tethered fuel cap from the hook on the fuel door. Reinstall the cap by turning it clockwise until it clicks. If the cap is not properly installed, the Malfunction Indicator Lamp come on. See Malfunction Indicator Lamp on page 5‑15 for more information.

The fuel cap is behind the fuel door on the vehicle's passenger side. To open the fuel door, push the rearward center edge in and release and it will open.

Filling the Tank

{ WARNING

Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling. Do not smoke near fuel or when refueling the vehicle. Do not use cellular phones. Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling the vehicle. This is against the law in some places. Do not re-enter the vehicle while pumping fuel. Keep children away from the fuel pump; never let children pump fuel.

Chevrolet Malibu Owner Manual - 2011

Black plate (40,1)

9-40

Driving and Operating

{ WARNING

Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way.

Do not top off or overfill the tank and wait a few seconds before removing the nozzle. Clean fuel from painted surfaces as soon as possible. See Exterior Care on page 10‑90.

{ WARNING If a fire starts while you are refueling, do not remove the nozzle. Shut off the flow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately.

Notice: If a new fuel cap is needed, be sure to get the right type of cap from your dealer. The wrong type of fuel cap might not fit properly, might cause the malfunction indicator lamp to light, and could damage the fuel tank and emissions system. See Malfunction Indicator Lamp on page 5‑15.

Filling a Portable Fuel Container

{ WARNING

Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others:

. Dispense fuel only into

approved containers.

. Do not fill a container while it

is inside a vehicle, in a vehicle's trunk, pickup bed, or on any surface other than the ground.

(Continued)

Chevrolet Malibu Owner Manual - 2011

Black plate (41,1)

WARNING (Continued)

. Bring the fill nozzle in contact

with the inside of the fill opening before operating the nozzle. Contact should be maintained until the filling is complete.

. Do not smoke while

pumping fuel.

. Do not use a cellular phone

while pumping fuel.

Towing

General Towing Information Only use towing equipment that has been designed for the vehicle. Contact your dealer or trailering dealer for assistance with preparing the vehicle for towing a trailer.

Driving and Operating

9-41

See the following trailer towing information in this section:

For information on driving while towing a trailer, see “Driving Characteristics and Towing Tips.” For maximum vehicle and trailer weights, see “Trailer Towing.” For information on equipment to tow a trailer, see “Towing Equipment.”

For information on towing a disabled vehicle, see Towing the Vehicle on page 10‑88. For information on towing the vehicle behind another vehicle such as a motor home, see Recreational Vehicle Towing on page 10‑88.

Chevrolet Malibu Owner Manual - 2011

Black plate (42,1)

9-42

Driving and Operating

Driving Characteristics and Towing Tips

{ WARNING

The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well — or even at all. The driver and passengers could be seriously injured. The vehicle may also be damaged; the resulting repairs would not be covered by the vehicle warranty. Pull a trailer only if all the steps in this section have been followed. Ask your dealer for advice and information about towing a trailer with the vehicle.

The vehicle can tow a trailer when equipped with the proper trailer towing equipment. For trailering capacity, see Trailer Towing on page 9‑45. Trailering changes handling, acceleration, braking, durability and fuel economy. With the added weight, the engine, transmission, wheel assemblies and tires are forced to work harder and under greater loads. The trailer also adds wind resistance, increasing the pulling requirements. For safe trailering, correctly use the proper trailering equipment. The following information has important trailering tips and rules for your safety and that of your passengers. Read this section carefully before pulling a trailer. Pulling a Trailer Here are some important points:

There are many laws, including speed limit restrictions that apply to trailering. Check for legal requirements with state or provincial police.

. Do not tow a trailer at all during the first 1 600 km (1,000 miles) the new vehicle is driven. The engine, axle or other parts could be damaged.

. During the first 800 km

(500 miles) that a trailer is towed, do not drive over 80 km/h (50 mph) and do not make starts at full throttle. This reduces wear on the vehicle. The vehicle can tow in D (Drive). Use a lower gear if the transmission shifts too often.

. Obey speed limit restrictions. Do

not drive faster than the maximum posted speed for trailers, or no more than 90 km/h (55 mph), to reduce wear on the vehicle.

Chevrolet Malibu Owner Manual - 2011

Black plate (43,1)

Driving with a Trailer Towing a trailer requires experience. Get familiar with handling and braking with the added trailer weight. The vehicle is now longer and not as responsive as the vehicle is by itself. Check all trailer hitch parts and attachments, safety chains, electrical connectors, lamps, tires and mirror adjustments. If the trailer has electric brakes, start the vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working. During the trip, check regularly to be sure that the load is secure, and the lamps and trailer brakes are working properly.

Driving and Operating

9-43

Towing with a Stability Control System When towing, the sound of the stability control system might be heard. The system is reacting to the vehicle movement caused by the trailer, which mainly occurs during cornering. This is normal when towing heavier trailers. Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer. This can help to avoid situations that require heavy braking and sudden turns. Passing More passing distance is needed when towing a trailer. Because the rig is longer, it is necessary to go farther beyond the passed vehicle before returning to the lane.

Backing Up Hold the bottom of the steering wheel with one hand. To move the trailer to the left, move that hand to the left. To move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you. Making Turns Notice: Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle. The vehicle could be damaged. Avoid making very sharp turns while trailering. When turning with a trailer, make wider turns than normal so the trailer will not strike soft shoulders, curbs, road signs, trees or other objects. Use the turn signal well in advance and avoid jerky or sudden maneuvers.

Chevrolet Malibu Owner Manual - 2011

Black plate (44,1)

9-44

Driving and Operating

The vehicle can tow in D (Drive). Use a lower gear if the transmission shifts too often. When towing at high altitude on steep uphill grades, engine coolant boils at a lower temperature than at normal altitudes. If the engine is turned off immediately after towing at high altitude on steep uphill grades, the vehicle could show signs similar to engine overheating. To avoid this, let the engine run while parked, preferably on level ground, with the transmission in P (Park) for a few minutes before turning the engine off. If the overheat warning comes on, see Engine Overheating on page 10‑20.

Turn Signals When Towing a Trailer The turn signal indicators on the instrument panel flash whenever signaling a turn or lane change. Properly hooked up, the trailer lamps also flash, telling other drivers the vehicle is turning, changing lanes or stopping. When towing a trailer, the arrows on the instrument panel flash for turns even if the bulbs on the trailer are burned out. Check occasionally to be sure the trailer bulbs are still working. Driving on Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the brakes might have to be used so much that they would get hot and no longer work well.

Parking on Hills

{ WARNING

Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.

If parking the rig on a hill: 1. Press the brake pedal, but do not shift into P (Park) yet. Turn the wheels into the curb if facing downhill or into traffic if facing uphill.

2. Have someone place chocks

under the trailer wheels.

3. When the wheel chocks are in place, release the brake pedal until the chocks absorb the load.

Chevrolet Malibu Owner Manual - 2011

Black plate (45,1)

4. Reapply the brake pedal. Then

apply the parking brake and shift into P (Park).

5. Release the brake pedal. Leaving After Parking on a Hill 1. Apply and hold the brake pedal. 2. Start the engine. 3. Shift into a gear. 4. Release the parking brake. 5. Let up on the brake pedal. 6. Drive slowly until the trailer is

clear of the chocks.

7. Stop and have someone pick up

and store the chocks.

Maintenance When Trailer Towing The vehicle needs service more often when pulling a trailer. See this manual's Maintenance Schedule or Index for more information. Things that are especially important in trailer operation are automatic transmission fluid, engine oil, axle lubricant, belts, cooling system and brake system. Inspect these before and during the trip. Check periodically to see that all hitch nuts and bolts are tight. Engine Cooling When Trailer Towing The cooling system may temporarily overheat during severe operating conditions. See Engine Overheating on page 10‑20.

Driving and Operating

9-45

Trailer Towing Before pulling a trailer, there are three important considerations that have to do with weight:

The weight of the trailer. The weight of the trailer tongue. The total weight on your vehicle's tires.

Weight of the Trailer How heavy can a trailer safely be? It should never weigh more than 454 kg (1,000 lbs). But even that can be too heavy. It depends on how the rig is used. For example, speed, altitude, road grades, outside temperature and how much the vehicle is used to pull a trailer are all important. It can depend on any special equipment on the vehicle, and the amount of tongue weight the vehicle can carry. See “Weight of the Trailer Tongue” later in this section for more information.

Chevrolet Malibu Owner Manual - 2011

Black plate (46,1)

9-46

Driving and Operating

Maximum trailer weight is calculated assuming only the driver is in the tow vehicle and it has all the required trailering equipment. The weight of additional optional equipment, passengers and cargo in the tow vehicle must be subtracted from the maximum trailer weight. Ask your dealer for trailering information or advice, or write us at our Customer Assistance Offices. See Customer Assistance Offices (U.S. and Canada) on page 13‑5 or Customer Assistance Offices (Mexico) on page 13‑5 for more information. Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.

If there are a lot of options, equipment, passengers or cargo in the vehicle, it will reduce the tongue weight the vehicle can carry, which will also reduce the trailer weight the vehicle can tow. If towing a trailer, the tongue load must be added to the GVW because the vehicle will be carrying that weight, too. See Vehicle Load Limits on page 9‑12
for more information.

After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they are not, adjustments might be made by moving some items around in the trailer. Total Weight on Your Vehicle's Tires Be sure the vehicle's tires are inflated to the upper limit for cold tires. These numbers can be found on the Tire-Loading Information label. See Vehicle Load Limits on page 9‑12. Make sure not to go over the GVW limit for the vehicle, including the weight of the trailer tongue.

The trailer tongue (A) should weigh 10‐15 percent of the total loaded trailer weight (B).

Chevrolet Malibu Owner Manual - 2011

Black plate (47,1)

Driving and Operating

9-47

Towing Equipment

Hitches Use the correct hitch equipment. See your dealer or a hitch dealer for assistance.

The rear bumper on the vehicle is not intended for hitches. Do not attach rental hitches or other bumper-type hitches to it. Use only a frame-mounted hitch that does not attach to the bumper. . Will any holes be made in the body of the vehicle when the trailer hitch is installed? If there are, seal the holes when the hitch is removed. If the holes are not sealed, dirt, water, and deadly carbon monoxide (CO) from the exhaust can get into the vehicle. See Engine Exhaust on page 9‑22.

Safety Chains Always attach chains between the vehicle and the trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Leave enough slack so the rig can turn. Never allow safety chains to drag on the ground. Trailer Brakes Does the trailer have its own brakes? Be sure to read and follow the instructions for the trailer brakes so they are installed, adjusted, and maintained properly. Because the vehicle has antilock brakes, do not tap into the vehicle's brake system. If this is done, both brake systems will not work well, or at all.

Conversions and Add-Ons

Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle's warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain the vehicle's 12‐volt battery, even if the vehicle is not operating. The vehicle has an airbag system. Before attempting to add anything electrical to the vehicle, see Servicing the Airbag-Equipped Vehicle on page 3‑36 and Adding Equipment to the Airbag-Equipped Vehicle on page 3‑37.

Chevrolet Malibu Owner Manual - 2011

Black plate (48,1)

9-48

Driving and Operating

2 NOTES

Chevrolet Malibu Owner Manual - 2011

Black plate (1,1)

Vehicle Care

General Information

General Information . . . . . . . . . . 10-2
California Proposition

65 Warning . . . . . . . . . . . . . . . . . 10-3

California Perchlorate

Materials Requirements . . . . 10-3

Accessories and

Modifications . . . . . . . . . . . . . . . 10-3

Vehicle Checks Doing Your Own

Service Work . . . . . . . . . . . . . . . 10-4
Hood . . . . . . . . . . . . . . . . . . . . . . . . 10-5
Engine Compartment

Overview . . . . . . . . . . . . . . . . . . . 10-6
Engine Oil . . . . . . . . . . . . . . . . . . . 10-9
Engine Oil Life System . . . . . 10-13
Automatic Transmission

Fluid . . . . . . . . . . . . . . . . . . . . . . 10-14
Engine Air Cleaner/Filter . . . . 10-14
Cooling System . . . . . . . . . . . . 10-16
Engine Coolant . . . . . . . . . . . . . 10-16
Engine Overheating . . . . . . . . 10-20
Overheated Engine

Protection Operating Mode . . . . . . . . . . . 10-21

Power Steering Fluid . . . . . . . 10-22
Washer Fluid . . . . . . . . . . . . . . . 10-23
Brakes . . . . . . . . . . . . . . . . . . . . . 10-24
Brake Fluid . . . . . . . . . . . . . . . . . 10-25
Battery . . . . . . . . . . . . . . . . . . . . . 10-26
Starter Switch Check . . . . . . . 10-27
Automatic Transmission Shift

Lock Control Function Check . . . . . . . . . . . . . . . . . . . . . 10-27

Ignition Transmission Lock

Check . . . . . . . . . . . . . . . . . . . . . 10-28

Park Brake and P (Park)

Mechanism Check . . . . . . . . 10-28

Wiper Blade

Replacement . . . . . . . . . . . . . . 10-29

Headlamp Aiming

Headlamp Aiming . . . . . . . . . . 10-29

Bulb Replacement

Bulb Replacement . . . . . . . . . . 10-30
Halogen Bulbs . . . . . . . . . . . . . . 10-30
Taillamps, Turn Signal, and

Stoplamps (LS and LT) . . . . 10-30

Taillamps, Turn Signal, and

Stoplamps (LTZ) . . . . . . . . . . 10-32
Back-Up Lamps . . . . . . . . . . . . 10-33
License Plate Lamp . . . . . . . . 10-34
Replacement Bulbs . . . . . . . . . 10-34

Vehicle Care

10-1

Electrical System

Electrical System

Overload . . . . . . . . . . . . . . . . . . 10-35
Fuses . . . . . . . . . . . . . . . . . . . . . . 10-35
Engine Compartment Fuse

Block . . . . . . . . . . . . . . . . . . . . . 10-36

Instrument Panel Fuse

Block . . . . . . . . . . . . . . . . . . . . . 10-38

Rear Compartment Fuse

Block . . . . . . . . . . . . . . . . . . . . . 10-40

Wheels and Tires

Tires . . . . . . . . . . . . . . . . . . . . . . . . 10-42
Winter Tires . . . . . . . . . . . . . . . . 10-43
Low-Profile Tires . . . . . . . . . . . 10-44
Tire Sidewall Labeling . . . . . . 10-44
Tire Designations . . . . . . . . . . . 10-47
Tire Terminology and

Definitions . . . . . . . . . . . . . . . . 10-48
Tire Pressure . . . . . . . . . . . . . . . 10-51
Tire Pressure for High-Speed

Operation . . . . . . . . . . . . . . . . . 10-52

Tire Pressure Monitor

System . . . . . . . . . . . . . . . . . . . 10-53

Tire Pressure Monitor

Operation . . . . . . . . . . . . . . . . . 10-54
Tire Inspection . . . . . . . . . . . . . . 10-57
Tire Rotation . . . . . . . . . . . . . . . 10-57

Chevrolet Malibu Owner Manual - 2011

Black plate (2,1)

10-2

Vehicle Care

Jump Starting

Jump Starting . . . . . . . . . . . . . . 10-84

Towing

Towing the Vehicle . . . . . . . . . 10-88
Recreational Vehicle

Towing . . . . . . . . . . . . . . . . . . . . 10-88

Appearance Care

Exterior Care . . . . . . . . . . . . . . . 10-90
Interior Care . . . . . . . . . . . . . . . . 10-94
Floor Mats . . . . . . . . . . . . . . . . . . 10-97

General Information For service and parts needs, visit your dealer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks:

When It Is Time for New

Tires . . . . . . . . . . . . . . . . . . . . . . 10-59
Buying New Tires . . . . . . . . . . . 10-59
Different Size Tires and

Wheels . . . . . . . . . . . . . . . . . . . 10-61

Uniform Tire Quality

Grading . . . . . . . . . . . . . . . . . . . 10-62

Wheel Alignment and Tire

Balance . . . . . . . . . . . . . . . . . . . 10-63
Wheel Replacement . . . . . . . . 10-64
Tire Chains . . . . . . . . . . . . . . . . . 10-65
If a Tire Goes Flat . . . . . . . . . . 10-65
Tire Sealant and

Compressor Kit . . . . . . . . . . . 10-67

Storing the Tire Sealant and

Compressor Kit . . . . . . . . . . . 10-74
Tire Changing . . . . . . . . . . . . . . 10-75
Compact Spare Tire . . . . . . . . 10-83

Chevrolet Malibu Owner Manual - 2011

Black plate (3,1)

California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.

California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in Remote Keyless Entry transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/ perchlorate.

Vehicle Care

10-3

Accessories and Modifications Adding non‐dealer accessories to the vehicle can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control, and stability control. Some of these accessories could even cause malfunction or damage not covered by the vehicle warranty. Damage to vehicle components resulting from the installation or use of non‐GM certified parts, including control module modifications, is not covered under the terms of the vehicle warranty and may affect remaining warranty coverage for affected parts.

Chevrolet Malibu Owner Manual - 2011

Black plate (4,1)

10-4

Vehicle Care

GM Accessories are designed to complement and function with other systems on the vehicle. Your GM dealer can accessorize the vehicle using genuine GM Accessories. When you go to your GM dealer and ask for GM Accessories, you will know that GM-trained and supported service technicians will perform the work using genuine GM Accessories. Also, see Adding Equipment to the Airbag-Equipped Vehicle on page 3‑37.

If doing some of your own service work, use the proper service manual. It tells you much more about how to service the vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 13‑15. This vehicle has an airbag system. Before attempting to do your own service work, see Servicing the Airbag-Equipped Vehicle on page 3‑36. Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Records on page 11‑8.

Vehicle Checks

Doing Your Own Service Work

{ WARNING You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it.

. Be sure you have

sufficient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task.

. Be sure to use the proper

nuts, bolts, and other fasteners. Metric and English fasteners can be easily confused. If the wrong fasteners are used, parts can later break or fall off. You could be hurt.

Chevrolet Malibu Owner Manual - 2011

Black plate (5,1)

Hood To open the hood:

1. Pull the hood release handle

with this symbol on it. It is located inside the vehicle to the left of the steering column.

2. Then go to the front of the

vehicle and push the secondary hood release handle toward the driver side of the vehicle.

Vehicle Care

10-5

3. Lift the hood. 4. After the hood is slightly lifted, it

will continue to open to the full position. Before closing the hood, be sure all the filler caps are on properly. Lower the hood until the lifting force of the strut is reduced, then release the hood to latch fully. Check to make sure the hood is closed and repeat the process if necessary.

Chevrolet Malibu Owner Manual - 2011

Black plate (6,1)

10-6

Vehicle Care

Engine Compartment Overview

2.4 L L4 Engine

Chevrolet Malibu Owner Manual - 2011

Black plate (7,1)

A. Engine Air Cleaner/Filter on

E. Engine Coolant Surge Tank.

page 10‑14.

B. Engine Cooling Fan (Out of

View). See Cooling System on page 10‑16.

C. Engine Oil Fill Cap. See “When

to Add Engine Oil” under Engine Oil on page 10‑9.

D. Engine Oil Dipstick (Out of

View). See “Checking Engine Oil” under Engine Oil on page 10‑9.

See Engine Coolant on page 10‑16.

F. Pressure Cap. See Cooling

System on page 10‑16. G. Brake Master Cylinder

Reservoir. See “Brake Fluid” under Brakes on page 10‑24.

Vehicle Care

10-7

H. Battery on page 10‑26. I. Windshield Washer Fluid

Reservoir. See “Adding Washer Fluid” under Washer Fluid on page 10‑23.

J. See Engine Compartment Fuse

Block on page 10‑36.

Chevrolet Malibu Owner Manual - 2011

Black plate (8,1)

10-8

Vehicle Care

3.6 L V6 Engine

Chevrolet Malibu Owner Manual - 2011

Black plate (9,1)

A. Engine Air Cleaner/Filter on

G. Pressure Cap. See Cooling

page 10‑14.

B. Power Steering Fluid Reservoir.

See Power Steering Fluid on page 10‑22.

C. Engine Oil Fill Cap. See “When

I.

to Add Engine Oil” under Engine Oil on page 10‑9. D. Engine Oil Dipstick. See

“Checking Engine Oil” under Engine Oil on page 10‑9.

E. Electric Engine Cooling Fans

(Out of View). See Cooling System on page 10‑16.

F. Engine Coolant Surge Tank.

See Engine Coolant on page 10‑16.

System on page 10‑16. H. Brake Master Cylinder

Reservoir. See “Brake Fluid” under Brakes on page 10‑24. Automatic Transmission Fluid Dipstick (Out of View). See “Checking the Fluid Level” under Automatic Transmission Fluid on page 10‑14.

J. See Battery on page 10‑26. K. Engine Compartment Fuse

Block on page 10‑36.

L. Windshield Washer Fluid

Reservoir. See “Adding Washer Fluid” under Washer Fluid on page 10‑23.

Vehicle Care

10-9

Engine Oil To ensure proper engine performance and long life, careful attention must be paid to engine oil. Following these simple, but important steps will help protect your investment: . Always use engine oil approved to the proper specification and of the proper viscosity grade. See “Selecting the Right Engine Oil” in this section.

. Check the engine oil level regularly and maintain the proper oil level. See “Checking Engine Oil” and “When to Add Engine Oil” in this section.

. Change the engine oil at the

appropriate time. See Engine Oil Life System on page 10‑13. . Always dispose of engine oil

properly. See “What to Do with Used Oil” in this section.

Chevrolet Malibu Owner Manual - 2011

Black plate (10,1)

10-10

Vehicle Care

Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 10‑6 for the location of the engine oil dipstick. Obtaining an accurate oil level reading is essential: 1.

If the engine has been running recently, turn off the engine and allow several minutesfor the oil to drain back into the oil pan. Checking the oil level too soon after engine shutoff will not provide an accurate oil level reading.

2. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level.

When to Add Engine Oil

L4 Engine

V6 Engine

If the oil is below the MIN (minimum) mark for the L4 engine or below the cross‐hatched area at the tip of the dipstick for the V6 engine, add 1 L (1 qt) of the recommended oil and then recheck the level. See “Selecting the Right Engine Oil” in this section for an explanation of what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 12‑2.

Notice: Do not add too much oil. Oil levels above or below the acceptable operating range shown on the dipstick are harmful to the engine. If you find that you have an oil level above the operating range, i.e., the engine has so much oil that the oil level gets above the upper mark that shows the proper operating range, the engine could be damaged. You should drain out the excess oil or limit driving of the vehicle and seek a service professional to remove the excess amount of oil. See Engine Compartment Overview on page 10‑6 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through.

Chevrolet Malibu Owner Manual - 2011

Black plate (11,1)

Selecting the Right Engine Oil Selecting the right engine oil depends on both the proper oil specification and viscosity grade:

Specification Use and ask for engine oils with the dexos™ certification mark. Oils meeting the requirements of the vehicle should have the dexos certification mark on the container. This certification mark indicates that the oil has been approved to the dexos specification.

Vehicle Care

10-11

Use of Substitute Engine Oils if dexos is unavailable: In the event that dexos‐approved engine oil is not available at an oil change or for maintaining proper oil level, you may use substitute engine oil displaying the API Starburst symbol and of SAE 5W-30 viscosity grade. Use of oils that do not meet the dexos specification, however, may result in reduced performance under certain circumstances.

Viscosity Grade SAE 5W-30 is the best viscosity grade for the vehicle. Do not use other viscosity oils such as SAE 10W‐30, 10W‐40, or 20W-50.

This vehicle was filled at the factory with dexos‐approved engine oil. Notice: Use only engine oil that is approved to the dexos specification or an equivalent engine oil of the appropriate viscosity grade. Engine oils approved to the dexos specification will show the dexos symbol on the container. Failure to use the recommended engine oil or equivalent can result in engine damage not covered by the vehicle warranty. If you are unsure whether the oil is approved to the dexos specification, ask your service provider.

Chevrolet Malibu Owner Manual - 2011

Black plate (12,1)

10-12

Vehicle Care

(−20°F), an SAE 0W-30 oil should be used. An oil of this viscosity grade will provide easier cold starting for the engine at extremely low temperatures. When selecting an oil of the appropriate viscosity grade, be sure to always select an oil that meets the required specification, dexos. See “Specification” earlier in this section for more information. Engine Oil Additives/Engine Oil Flushes Do not add anything to the oil. The recommended oils with the dexos specification and displaying the dexos certification mark are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty.

What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags containing used engine oil. See the manufacturer's warnings about the use and disposal of oil products. Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the filter before disposal. Never dispose of oil by putting it in the trash or pouring it on the ground, into sewers, or into streams or bodies of water. Recycle it by taking it to a place that collects used oil.

Cold Temperature Operation: In an area of extreme cold, where the temperature falls below −29°C

Chevrolet Malibu Owner Manual - 2011

Black plate (13,1)

Engine Oil Life System

When to Change Engine Oil This vehicle has a computer system that indicates when to change the engine oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change is indicated can vary considerably. For the oil life system to work properly, the system must be reset every time the oil is changed. When the system has calculated that oil life has been diminished, it indicates that an oil change is necessary. A CHANGE OIL SOON message comes on. See Engine Oil Messages on page 5‑26. Change the oil as soon as possible within the next 1 000 km (600 miles). It is possible that, if driving under the

best conditions, the oil life system might indicate that an oil change is not necessary for up to a year. The engine oil and filter must be changed at least once a year and, at this time, the system must be reset. Your dealer has trained service people who will perform this work and reset the system. It is also important to check the oil regularly over the course of an oil drain interval and keep it at the proper level. If the system is ever reset accidentally, the oil must be changed at 5 000 km (3,000 miles) since the last oil change. Remember to reset the oil life system whenever the oil is changed.

Vehicle Care

10-13

How to Reset the Engine Oil Life System Reset the system whenever the engine oil is changed so that the system can calculate the next engine oil change. To reset the system: 1. Turn the ignition to ON/RUN,

with the engine off.

2. Press and hold the DIC INFO and reset buttons, on the left side of the steering wheel, at the same time to enter the personalization menu. The OIL LIFE RESET message displays. See Driver Information Center (DIC) on page 5‑22 and Engine Oil Messages on page 5‑26.

3. Press and hold the reset button

until the DIC display shows ACKNOWLEDGED.

4. Turn the key to LOCK/OFF. The system is reset when the CHANGE OIL SOON message is off.

Chevrolet Malibu Owner Manual - 2011

Black plate (14,1)

10-14

Vehicle Care

If the CHANGE OIL SOON message comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the procedure.

Automatic Transmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to the dealer and have it repaired as soon as possible. Change the fluid and filter at the intervals listed in Scheduled Maintenance on page 11‑2, and be sure to use the transmission fluid listed in Recommended Fluids and Lubricants on page 11‑6.

Notice: Use of the incorrect automatic transmission fluid may damage the vehicle, and the damages may not be covered by the vehicle warranty. Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 11‑6. For the 2.4 L and 3.6 L engines, the transmission fluid will not reach the end of the dipstick unless the transmission is at operating temperature. If the transmission fluid level needs to be checked, please take the vehicle to the dealer.

Engine Air Cleaner/Filter See Engine Compartment Overview on page 10‑6 for the location of the engine air cleaner/filter.

When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the scheduled maintenance intervals and replace it at the first oil change after each 80 000 km (50,000 mi) interval. See Scheduled Maintenance on page 11‑2 for more information. If driving in dusty/dirty conditions, inspect the filter at each engine oil change. How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release