Login- Download PDF Manual
-
11. Press the on/off button (1) to
turn the tire sealant and compressor kit off. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.
12. Unplug the power plug (7) from
the accessory power outlet in the vehicle.
13. Disconnect the air only
hose (5) from the tire valve stem, by turning it counterclockwise, and replace the tire valve stem cap.
14. Return the air only hose (5)
and the power plug (7) back to their original locations.
15. Return the equipment to its
original storage location in the vehicle.
Vehicle Care
10-75
Removal and Installation of the Sealant Canister To remove the sealant canister:
1. Remove the plastic cover. 2. Unscrew the connector (2) from
the canister (1).
3. Pull up on the canister (1) to
remove it.
4. Replace with a new canister which is available from your dealer.
5. Push the new canister into
place.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (76,1)
10-76
Vehicle Care
6. Screw the connector (2) to the
canister (1).
7. Slide the plastic cover back on.
Tire Sealant and Compressor Kit (With Pressure Deflation Button)
System Identification
If the vehicle has the tire sealant and compressor kit shown above, see the operating instructions that follow.
Warning (Continued)
which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 9-26.
{ Warning
Overinflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure.
If the vehicle has the tire sealant and compressor kit shown above, follow the operating instructions under "Tire Sealant and Compressor Kit (With Pressure Relief Button).”
{ Warning
Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains carbon monoxide (CO)
(Continued)
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (77,1)
Vehicle Care
10-77
The kit includes:
{ Warning
Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.
If this vehicle has a tire sealant and compressor kit, there may not be a spare tire and tire changing equipment, and on some vehicles there may not be a place to store a tire.
The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (0.25 in) in the tread area of the tire. It can also be used to inflate an underinflated tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program on page 13-5. Read and follow all of the tire sealant and compressor kit instructions.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (78,1)
10-78
Vehicle Care
1. Selector Switch (Sealant/Air
or Air Only)
2. On/Off Button 3. Pressure Gauge 4. Pressure Deflation Button
(If equipped)
5. Tire Sealant Canister 6. Sealant/Air Hose (Clear) 7. Air Only Hose (Black) 8. Power Plug 9. Canister Release Button (Under Sealant/Air Hose)
Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date.
Replacement sealant canisters are available at your local dealer. See “Removal and Installation of the Sealant Canister” following. There is only enough sealant to seal one tire. After usage, the sealant canister and sealant/air hose assembly must be replaced. See “Removal and Installation of the Sealant Canister” following. Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage.
When using the tire sealant and compressor kit during cold temperatures, warm the kit in a
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (79,1)
Vehicle Care
10-79
heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-3. See If a Tire Goes Flat on page 10-67 for other important safety warnings. Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and
compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10-83.
2. Unwrap the sealant/air hose (6)
and the power plug (8).
3. Place the kit on the ground.
4. Remove the valve stem cap from
9. Press the on/off button (2) to
the flat tire by turning it counterclockwise.
5. Attach the sealant/air hose (6) onto the tire valve stem. Turn it clockwise until it is tight.
6. Plug the power plug (8) into the
accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5-5. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.
7. Start the vehicle. The vehicle
must be running while using the air compressor.
turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gauge (3) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inflates with air only.
Inflate the tire to the recommended inflation pressure using the pressure gauge (3). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10-53.
10.
Make sure the tire valve stem is positioned close to the ground so the hose will reach it.
8. Press and turn the selector
switch (1) counterclockwise to the Sealant + Air position.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (80,1)
10-80
Vehicle Care
The pressure gauge (3) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached.
{ Caution
If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program on page 13-5.
11. Press the on/off button (2) to
turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire; therefore, Steps 12–18 must be done immediately after Step 11. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.
12. Unplug the power plug (8) from
the accessory power outlet in the vehicle.
13. Turn the sealant/air hose (6)
counterclockwise to remove it from the tire valve stem.
14. Replace the tire valve
stem cap.
15. Replace the sealant/air hose
(6), and the power plug (8) back in their original location.
16.
If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the tire sealant canister (5) and place it in a highly visible location. Do not exceed the speed on this label until the damaged tire is repaired or replaced.
17. Return the equipment to its
18.
original storage location in the vehicle. Immediately drive the vehicle 8 km (5 mi) to distribute the sealant in the tire.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (81,1)
Vehicle Care
10-81
19. Stop at a safe location and
check the tire pressure. Refer to Steps 1–11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured).” If the tire pressure has fallen more than 68 kPa (10 psi) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program on page 13-5. If the tire pressure has not dropped more than 68 kPa (10 psi) from the recommended inflation pressure, inflate the tire to the recommended inflation pressure.
20. Wipe off any sealant from the
wheel, tire, and vehicle.
21. Dispose of the used tire sealant canister (5) and sealant/air hose (6) assembly at a local dealer or in accordance with local state codes and practices.
22. Replace it with a new canister
available from your dealer.
23. After temporarily sealing a tire
using the tire sealant and compressor kit, take the vehicle to an authorized dealer within a 161 km (100 mi) of driving to have the tire repaired or replaced.
Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant:
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (82,1)
10-82
Vehicle Care
If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-3. See If a Tire Goes Flat on page 10-67 for other important safety warnings. 1. Remove the tire sealant and
compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10-83.
2. Unwrap the air only hose (7) and
the power plug (8).
3. Place the kit on the ground.
Make sure the tire valve stem is positioned close to the ground so the hose will reach it.
4. Remove the tire valve stem cap
from the flat tire by turning it counterclockwise.
5. Attach the air only hose (7) onto
the tire valve stem by turning it clockwise until it is tight.
6. Plug the power plug (8) into the
10.
accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5-5. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.
7. Start the vehicle. The vehicle
must be running while using the air compressor.
8. Press and turn the selector
switch (1) clockwise to the Air Only position.
9. Press the on/off button (2) to
turn the compressor on. The compressor will inflate the tire with air only.
Inflate the tire to the recommended inflation pressure using the pressure gauge (3). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10-53. The pressure gauge (3) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate reading. The compressor may be turned on/ off until the correct pressure is reached. If you inflate the tire higher than the recommended pressure you can adjust the excess pressure by pressing the pressure deflation button (4), if equipped, until the proper pressure reading is reached. This option is only functional when using the air only hose (7).
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (83,1)
Vehicle Care
10-83
3. Pull up and remove the canister. 4. Replace with a new canister which is available from your dealer.
5. Push the new canister into
place.
Storing the Tire Sealant and Compressor Kit To access the tire sealant and compressor kit: 1. Open the trunk. See Trunk on
page 2-14.
2. Lift the cover.
11. Press the on/off button (2) to
turn the tire sealant and compressor kit off. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.
12. Unplug the power plug (8) from
the accessory power outlet in the vehicle.
13. Disconnect the air only hose
(7) from the tire valve stem by turning it counterclockwise, and replace the tire valve stem cap.
14. Replace the air only hose (7)
and the power plug (8) and cord back in their original locations.
15. Place the equipment in the
original storage location in the vehicle.
The tire sealant and compressor kit has an accessory adapter in a compartment on the bottom of its housing that may be used to inflate air mattresses, balls, etc. Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Unwrap the sealant hose. 2. Press the canister release
button (9).
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (84,1)
10-84
Vehicle Care
3. Turn the wing nut
counterclockwise to remove it.
4. Remove the tire sealant and
compressor kit.
To store the tire sealant and compressor kit, reverse the steps.
Tire Changing
Removing the Spare Tire and Tools
4. Wrench (In Bag) 5. Trim Removal (If Equipped) 6. Fastener (If Equipped)
To access the spare tire and tools: 1. Open the trunk. 2. Remove the spare tire cover.
With Pressure Relief Button
With Pressure Deflation Button
1. Screwdriver (If Equipped) 2. Tow Hook (If Equipped) 3. Jack
3. Turn the retainer nut
counterclockwise and remove the spare tire. Place the spare tire next to the tire being changed.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (85,1)
4. The jack and tools are stored below the spare tire. Remove them from their container and place them near the tire being changed.
Removing the Flat Tire and Installing the Spare Tire
2. Turn the wheel wrench
counterclockwise to loosen and remove the wheel nut caps. Do not try to remove plastic caps from the cover or center cap.
3. Pull the cover or center cap
away from the wheel. Store the wheel cover in the cargo area until you have the flat tire repaired or replaced.
Take off the wheel cover or center cap, if the vehicle has one, to reach the wheel bolts. 1. Do a safety check before
proceeding. See If a Tire Goes Flat on page 10-67.
4. Turn the wheel wrench
counterclockwise to loosen all the wheel nuts, but do not remove them yet.
Vehicle Care
10-85
5. Place the jack near the flat tire. 6. Put the compact spare tire
near you.
{ Warning
Getting under a vehicle when it is lifted on a jack is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.
{ Warning
Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (86,1)
10-86
Vehicle Care
{ Warning
{ Caution
Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.
7. Attach the jack lift assist tool to the jack by fitting both ends of the jack and tool over one another.
8. Place the jack under the vehicle.
Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty.
9. Position the jack lift head at the jack location nearest the flat tire. The location is indicated by a notch on the bottom edge of the body side. The jack must not be used in any other position.
10. Raise the vehicle by turning the
jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the road tire to clear the ground.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (87,1)
Vehicle Care
10-87
Warning (Continued)
{ Warning
an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.
Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.
11. Remove all of the wheel nuts. 12. Remove the flat tire. { Warning
Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In
(Continued)
13. Remove any rust or dirt from
the wheel bolts, mounting surfaces, and spare wheel.
14. Place the compact spare tire
on the wheel-mounting surface.
15. Reinstall the wheel nuts.
Tighten each nut by hand until the wheel is held against the hub.
16. Lower the vehicle by turning
the jack handle counterclockwise.
{ Warning
Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the
(Continued)
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (88,1)
10-88
Vehicle Care
Warning (Continued)
aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12-2 for original equipment wheel nut torque specifications.
{ Caution
Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications for the wheel nut torque specification.
{ Caution
Wheel covers will not fit on the vehicle's compact spare. If you try to put a wheel cover on the compact spare, the cover or the spare could be damaged.
Storing a Flat or Spare Tire and Tools
{ Warning
Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Store the spare or flat tire in one of the ways shown below. Storage instructions will vary depending on the bolt that came with the vehicle
17. Tighten the wheel nuts firmly in
a crisscross sequence, as shown.
18. Lower the jack all the way and remove the jack from under the vehicle.
19. Tighten the wheel nuts firmly
with the wheel wrench.
When reinstalling the wheel cover or center cap on the full-size tire, tighten all five plastic caps hand snug, then tighten them with the wheel wrench an additional one-quarter turn.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (89,1)
Vehicle Care
10-89
3. Turn the wrench clockwise to
tighten the fastener.
4. Replace the foam, jack and
tools, and the tire in their original storage location.
5. Place the tire, lying flat, facing
up in the spare tire well.
6. Turn the retainer nut clockwise
to secure the tire.
7. Place the floor cover on the
wheel.
Storing a Flat or Spare Tire and Tools with a Slide In Fastener 1.
If the flat tire is larger than the spare tire, use the longer mounting bolt from the tool bag.
and how it attaches to the vehicle. This vehicle will have a slide in fastener or a screw in fastener.
Storing a Flat or Spare Tire and Tools with a Screw in Fastener
1. Turn the wrench
counterclockwise to remove the fastener.
2. Replace the fastener with the
one provided in the foam. Use the longer fastener to store the flat tire.
2. Slide the shorter bolt to remove
it from the floor and insert the longer one.
3. Replace the jack and tools in their original storage location. 4. Place the tire, lying flat, facing
up in the spare tire well.
5. Turn the retainer nut clockwise
to secure the tire.
6. Place the floor cover on the
wheel.
To store the compact spare tire, use the shorter mounting bolt.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (90,1)
10-90
Vehicle Care
The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can.
Compact Spare Tire
{ Warning
Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.
If this vehicle has a compact spare tire, it was fully inflated when new; however, it can lose air over time. Check the inflation pressure regularly. It should be 420 kPa (60 psi).
Stop as soon as possible and check that the spare tire is correctly inflated after being installed on the vehicle. The compact spare tire is designed for temporary use only. The vehicle will perform differently with the spare tire installed and it is recommended that the vehicle speed be limited to 80 km/h (50 mph). To conserve the tread of the spare tire, have the standard tire repaired or replaced as soon as convenient and return the spare tire to the storage area. When using a compact spare tire, the ABS and Traction Control systems may engage until the spare tire is recognized by the vehicle, especially on slippery roads. Adjust driving to reduce possible wheel slip.
{ Caution
When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails which can damage the tire, wheel, and other parts of the vehicle.
Do not use the compact spare on other vehicles. Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together.
{ Caution
Tire chains will not fit the compact spare. Using them can damage the vehicle and the chains. Do not use tire chains on the compact spare.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (91,1)
Jump Starting
Jump Starting (On-board with eAssist Only) If the vehicle fails to crank, it may be jump started by using the eAssist battery to charge the 12-volt battery. Use the following procedure to activate the on-board jump start using the DIC controls.
DIC Buttons
1. SET/CLR 2. w / x (Thumbwheel) 3. MENU The vehicle may be equipped with an ignition key or an electronic keyless ignition with pushbutton start.
Key Access Place the ignition key in the ON/ RUN position and proceed as follows: 1. Press MENU (3) on the turn
signal lever until Vehicle Information Menu is displayed. Use w / x (Thumbwheel) (2) to scroll through the menu items until Jump Start is displayed.
2. Press SET/CLR (1) to activate
the jump start.
3. The system will then ask for
confirmation. If yes is selected, the jump start will begin and the display will show JUMP START ACTIVE WAIT TO START.
4. When the jump start is complete,
the display will show JUMP START COMPLETE ATTEMPT START.
Vehicle Care
10-91
Keyless Access With the brake pedal not applied, press and hold the ENGINE START/ STOP button for more than five seconds. This will place the vehicle in the Service Only Mode. Proceed as follows: 1. Press MENU (3) on the turn
signal lever until Vehicle Information Menu is displayed. Use w / x (Thumbwheel) (2) to scroll through the menu items until Jump Start is displayed.
2. Press SET/CLR (1) to activate
the jump start.
3. The system will then ask for
confirmation. If yes is selected, the jump start will begin and the display will show JUMP START ACTIVE WAIT TO START.
4. When the jump start is complete,
the display will show JUMP START COMPLETE ATTEMPT START.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (92,1)
10-92
Vehicle Care
If the vehicle is started, the on-board jump start function will be automatically disabled. If the vehicle cranks but does not start, the procedure may be repeated again. If the vehicle start is still unsuccessful, the jump start can be attempted using the following jump starting procedure under “Jump Starting (with or without eAssist).” On-board jump starting may be unavailable due to the 12-volt battery charge level, the eAssist battery charge level, power capability, or an issue with the eAssist system. In these cases, the display will not be available because of the power issue, or the DIC will display JUMP START DISABLED SEE OWNERS MANUAL.
Jump Starting (with or without eAssist) For more information about the vehicle battery, see Battery on page 10-24.
{ Caution
Ignoring these steps could result in costly damage to the vehicle that would not be covered by the vehicle warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle.
The vehicle has a battery cover which must be removed to gain access to the battery for jump starting.
If the battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.
{ Warning
Batteries can hurt you. They can be dangerous because:
. They contain acid that can
burn you.
. They contain gas that can
explode or ignite.
. They contain enough electricity to burn you.
If you do not follow these steps exactly, some or all of these things can hurt you.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (93,1)
1. Clips 2. Pivot Points To remove the battery cover: 1. Release the two rear clips (1). 2. Lift the battery cover up towards the front of the vehicle to release it from the pivot points (2) and remove.
3. Reverse Steps 1–2 to reinstall
the battery cover.
The vehicle has a remote positive (+) terminal under a trim cover. It is under the battery cover
on the driver side of the engine compartment. See Engine Compartment Overview on page 10-5. You should always use this remote positive (+) terminal. The jump start negative grounding point for the discharged battery is the engine block or an engine mounting bolt. Connect to a spot as far away from the discharged battery as possible. 1. Check the other vehicle. It must
have a 12-volt battery with a negative ground system.
{ Caution
If the other vehicle does not have a 12-volt system with a negative ground, both vehicles can be damaged. Only use a vehicle that has a 12-volt system with a negative ground for jump starting.
Vehicle Care
10-93
2. Position the two vehicles so that
they are not touching. To avoid the possibility of the vehicles rolling, set the parking brake firmly on both vehicles involved in the jump start procedure. Put an automatic transmission in P (Park) or a manual transmission in Neutral before setting the parking brake.
3. Set the parking brake firmly on both vehicles. Put an automatic transmission in P (Park) or a manual transmission in Neutral before setting the parking brake.
{ Caution
If any accessories are left on or plugged in during the jump starting procedure, they could be damaged. The repairs would not be covered by the vehicle warranty. Whenever possible, turn off or unplug all accessories on either vehicle when jump starting.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (94,1)
10-94
Vehicle Care
4. Turn the ignition to LOCK/OFF
and switch off all lights and accessories in both vehicles, except the hazard warning flashers if needed.
{ Warning
An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.
{ Warning
Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light.
(Continued)
Warning (Continued)
Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle. But if a battery has filler caps, be sure the right amount of fluid is there. If it is low, add water to take care of that first. If you do not, explosive gas could be present. Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.
{ Warning
Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.
6. Connect the red positive (+)
cable to the remote positive (+) terminal of the discharged battery.
7. Connect the other end of the
positive (+) cable to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
8. Connect one end of the black
negative (−) cable to the negative (−) terminal of the good battery.
9. Connect the other end of the
negative (−) to the negative (–) grounding point for the discharged battery.
10. Start the vehicle with the good
battery and run the engine at idle speed for at least four minutes.
11. Try to start the vehicle that had
the dead battery. If it will not start after a few tries, it probably needs service.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (95,1)
{ Caution If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Jumper Cable Removal Reverse the sequence exactly when removing the jumper cables.
Towing the Vehicle
{ Caution
Incorrectly towing a disabled vehicle may cause damage. The damage would not be covered by the vehicle warranty. Do not lash or hook to the chassis components — including the front and rear subframes, suspension control arms, and links — during towing and recovery of a disabled vehicle, or when securing the vehicle. Use the proper nylon strap harnesses around the tires to secure the vehicle.
Have the vehicle towed on a wheel lift tow truck. A flatbed car carrier could damage the vehicle. The wheel lift tow truck must raise the rear of the vehicle and wheel dollies must be used to lift the front wheels off the ground.
Vehicle Care
10-95
Consult your dealer or a professional towing service if the disabled vehicle must be towed. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motor home, see “Recreational Vehicle Towing” following.
Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motor home. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground. Dolly towing is towing the vehicle with two wheels on the ground and two wheels up on a device known as a dolly.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (96,1)
10-96
Vehicle Care
Here are some important things to consider before recreational vehicle towing: . What is the towing capacity of the towing vehicle? Be sure to read the tow vehicle manufacturer's recommendations.
. How far will the vehicle be
towed? Some vehicles have restrictions on how far and how long they can tow.
. Does the vehicle have the
proper towing equipment? See your dealer or trailering professional for additional advice and equipment recommendations. Is the vehicle ready to be towed? Just as preparing the vehicle for a long trip, make sure the vehicle is prepared to be towed.
Dinghy Towing (with eAssist)
Vehicles with eAssist should not be towed with all four wheels on the ground. If the vehicle must be towed, a dolly should be used. See “Dolly Towing” following. Dinghy Towing (without eAssist)
{ Caution
If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty. Do not tow the vehicle with all four wheels on the ground.
To dinghy tow the vehicle from the front with all four wheels on the ground: 1. Position the vehicle to tow and
then secure it to the towing vehicle.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (97,1)
2. Shift the transmission to Neutral. 3. Place the ignition in the ACC/
ACCESSORY position. See Ignition Positions (Keyless Access) on page 9-15 or Ignition Positions (Key Access) on page 9-17.
4. To prevent the battery from draining while the vehicle is being towed, remove fuse 8, 22
(Key Access only), and 24, from the instrument panel fuse block. See Instrument Panel Fuse Block on page 10-42.Remember to reinstall the fuses once the destination has been reached.
{ Caution
If 105 km/h (65 mph) is exceeded while towing the vehicle, it could be damaged. Never exceed 105 km/h (65 mph) while towing the vehicle.
Dolly Towing
Vehicle Care
10-97
{ Caution
Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty. Never have the vehicle towed from the rear.
Tow the vehicle with the two rear wheels on the ground and the front wheels on a dolly. To tow the vehicle with two wheels on the ground and a dolly: 1. Put the front wheels on a dolly. 2. Put the shift lever in P (Park). 3. Secure the vehicle to the dolly.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (98,1)
10-98
Vehicle Care
Appearance Care
Exterior Care
Locks Locks are lubricated at the factory. Use a de-icing agent only when absolutely necessary, and have the locks greased after using. See Recommended Fluids and Lubricants on page 11-12. Washing the Vehicle To preserve the vehicle's finish, wash it often and out of direct sunlight.
{ Caution
Do not use petroleum-based, acidic, or abrasive cleaning agents as they can damage the vehicle's paint, metal, or plastic parts. If damage occurs, it would not be covered by the vehicle warranty. Approved cleaning
(Continued)
Caution (Continued)
products can be obtained from your dealer. Follow all manufacturer directions regarding correct product usage, necessary safety precautions, and appropriate disposal of any vehicle care product.
{ Caution Avoid using high-pressure washes closer than 30 cm (12 in) to the surface of the vehicle. Use of power washers exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals.
Thee symbol is on any underhood compartment electrical center that should not be power
washed. This could cause damage that would not be covered by the vehicle warranty. If using an automatic car wash, follow the car wash instructions. The windshield wiper and rear window wiper, if equipped, must be off. Remove any accessories that may be damaged or interfere with the car wash equipment. Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. Finish Care Application of aftermarket clearcoat sealant/wax materials is not recommended. If painted surfaces are damaged, see your dealer to have the damage assessed and repaired. Foreign materials such as
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (99,1)
Caution (Continued)
may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle.
To keep the paint finish looking new, keep the vehicle garaged or covered whenever possible.
Protecting Exterior Bright Metal Moldings
{ Caution
Failure to clean and protect the bright metal moldings can result in a hazy white finish or pitting. This damage would not be covered by the vehicle warranty.
Vehicle Care
10-99
The bright metal moldings on the vehicle are aluminum. To prevent damage always follow these cleaning instructions: . Be sure the molding is cool to the touch before applying any cleaning solution.
. Use a cleaning solution
approved for aluminum. Some cleaners are highly acidic or contain alkaline substances and can damage the moldings.
. Always dilute a concentrated
cleaner according to the manufacturer’s instructions. . Do not use chrome cleaners. . Do not use cleaners that are not
intended for automotive use.
. Use a nonabrasive wax on the vehicle after washing to protect and extend the molding finish.
calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Occasional hand waxing or mild polishing should be done to remove residue from the paint finish. See your dealer for approved cleaning products. Do not apply waxes or polishes to uncoated plastic, vinyl, rubber, decals, simulated wood, or flat paint as damage can occur.
{ Caution Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish
(Continued)
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (100,1)
10-100
Vehicle Care
Cleaning Exterior Lamps/ Lenses, Emblems, Decals and Stripes Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps, lenses, emblems, decals, and stripes. Follow instructions under "Washing the Vehicle" previously in this section. Lamp covers are made of plastic, and some have a UV protective coating. Use only lukewarm water, a soft cloth, and mild car washing soap to clean exterior lamps and lenses. Do not clean or wipe them while they are dry. Do not use any of the following on lamp covers: . Abrasive or caustic agents. . Washer fluids and other cleaning
agents in higher concentrations than suggested by the manufacturer.
. Solvents, alcohols, fuels, or other harsh cleaners. Ice scrapers or other hard items. . Aftermarket appearance caps or
covers while the lamps are illuminated, due to excessive heat generated.
{ Caution
Failure to clean lamps properly can cause damage to the lamp cover that would not be covered by the vehicle warranty.
{ Caution
Using wax on low gloss black finish stripes can increase the gloss level and create a non-uniform finish. Clean low gloss stripes with soap and water only.
Air Intakes Clear debris from the air intakes, between the hood and windshield when washing the vehicle. Shutter System
The vehicle may have a shutter system designed to help increase fuel economy. Keep the shutter system clean for proper operation.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (101,1)
Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean rubber blades using a lint-free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking. Replace the wiper blades if they are worn or damaged. Damage can be caused by extreme dusty conditions, sand, salt, heat, sun, snow, and ice. Weatherstrips Apply Dielectric silicone grease on weatherstrips to make them last longer, seal better, and not stick or squeak. Lubricate weatherstrips at least once a year. Hot, dry climates may require more frequent application. Black marks from rubber material on painted surfaces
can be removed by rubbing with a clean cloth. See Recommended Fluids and Lubricants on page 11-12. Tires Use a stiff brush with tire cleaner to clean the tires.
{ Caution
Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/ or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Wheels and Trim — Aluminum or Chrome Use a soft, clean cloth with mild soap and water to clean the wheels. After rinsing thoroughly with clean water, dry with a soft, clean towel. A wax may then be applied.
Vehicle Care
10-101
{ Caution
Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium, or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash the chrome with soap and water after exposure.
{ Caution
To avoid surface damage, do not use strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels. Use only approved cleaners. Also, never drive a vehicle with aluminum or chrome-plated wheels through an (Continued)
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (102,1)
10-102
Vehicle Care
Caution (Continued)
automatic car wash that uses silicone carbide tire cleaning brushes. Damage could occur and the repairs would not be covered by the vehicle warranty.
Steering, Suspension, and Chassis Components Visually inspect steering, suspension, and chassis components for damaged, loose, or missing parts or signs of wear at least once a year. Inspect power steering for proper hook-up, binding, leaks, cracks, chafing, etc. Visually check constant velocity joint boots and axle seals for leaks. Body Component Lubrication Lubricate all key lock cylinders, hood hinges, liftgate hinges, and the steel fuel door hinge unless the components are plastic. Applying
silicone grease on weatherstrips with a clean cloth will make them last longer, seal better, and not stick or squeak. Underbody Maintenance At least twice a year, spring and fall, use plain water to flush dirt and debris from the vehicle's underbody. Your dealer or an underbody car washing system can do this. If not removed, rust and corrosion can develop. Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty.
Finish Damage Quickly repair minor chips and scratches with touch-up materials available from your dealer to avoid corrosion. Larger areas of finish damage can be corrected in your dealer's body and paint shop. Chemical Paint Spotting Airborne pollutants can fall upon and attack painted vehicle surfaces causing blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. See “Finish Care” previously in this section.
Interior Care To prevent dirt particle abrasions, regularly clean the vehicle's interior. Immediately remove any soils. Note that newspapers or dark garments that can transfer color to home furnishings can also permanently transfer color to the vehicle's interior.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (103,1)
Use a soft bristle brush to remove dust from knobs and crevices on the instrument cluster. Using a mild soap solution, immediately remove hand lotions, sunscreen, and insect repellent from all interior surfaces or permanent damage may result. Your dealer may have products for cleaning the interior. Use cleaners specifically designed for the surfaces being cleaned to prevent permanent damage. Apply all cleaners directly to the cleaning cloth. Do not spray cleaners directly on any switches or controls. Cleaners should be removed quickly. Never allow cleaners to remain on the surface being cleaned for extended periods of time. Cleaners may contain solvents that can become concentrated in the interior. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning the interior, maintain adequate ventilation by opening the doors and windows.
To prevent damage, do not clean the interior using the following cleaners or techniques: . Never use a razor or any other
sharp object to remove a soil from any interior surface.
. Never use a brush with stiff
bristles.
. Never rub any surface
aggressively or with excessive pressure.
. Do not use laundry detergents or
dishwashing soaps with degreasers. For liquid cleaners, use approximately 20 drops per 3.8 L (1 gal) of water. A concentrated soap solution will leave a residue that creates streaks and attracts dirt. Do not use solutions that contain strong or caustic soap.
. Do not heavily saturate the upholstery when cleaning.
. Do not use solvents or cleaners
containing solvents.
Vehicle Care
10-103
Interior Glass To clean, use a terry cloth fabric dampened with water. Wipe droplets left behind with a clean dry cloth. Commercial glass cleaners may be used, if necessary, after cleaning the interior glass with plain water.
{ Caution
To prevent scratching, never use abrasive cleaners on automotive glass. Abrasive cleaners or aggressive cleaning may damage the rear window defogger.
Cleaning the windshield with water during the first three to six months of ownership will reduce tendency to fog. Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (104,1)
10-104
Vehicle Care
Coated Moldings Coated moldings should be cleaned. . When lightly soiled, wipe with a
sponge or soft lint-free cloth dampened with water.
. When heavily soiled, use warm
soapy water.
Fabric/Carpet/Suede Start by vacuuming the surface using a soft brush attachment. If a rotating brush attachment is being used during vacuuming, only use it on the floor carpet. Before cleaning, gently remove as much of the soil as possible using one of the following techniques: . Gently blot liquids with a paper towel. Continue blotting until no more soil can be removed. For solid soils, remove as much as possible prior to vacuuming.
To clean: 1. Saturate a clean lint-free colorfast cloth with water. Microfiber cloth is recommended to prevent lint transfer to the fabric or carpet.
2. Remove excess moisture by
gently wringing until water does not drip from the cleaning cloth. 3. Start on the outside edge of the
soil and gently rub toward the center. Fold the cleaning cloth to a clean area frequently to prevent forcing the soil in to the fabric.
4. Continue gently rubbing the soiled area until there is no longer any color transfer from the soil to the cleaning cloth. If the soil is not completely removed, use a mild soap solution followed only by plain water.
5.
If the soil is not completely removed, it may be necessary to use a commercial upholstery
cleaner or spot lifter. Test a small hidden area for colorfastness before using a commercial upholstery cleaner or spot lifter. If ring formation occurs, clean the entire fabric or carpet. Following the cleaning process, a paper towel can be used to blot excess moisture. Cleaning High Gloss Surfaces and Vehicle Information and Radio Displays For vehicles with high gloss surfaces or vehicle displays, use a microfiber cloth to wipe surfaces. Before wiping the surface with the microfiber cloth, use a soft bristle brush to remove dirt that could scratch the surface. Then use the microfiber cloth by gently rubbing to clean. Never use window cleaners or solvents. Periodically hand wash the microfiber cloth separately, using mild soap. Do not use bleach or fabric softener. Rinse thoroughly and air dry before next use.
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (105,1)
Caution (Continued)
may cause permanent damage. Wipe excess moisture from these surfaces after cleaning and allow them to dry naturally. Never use heat, steam, spot lifters, or spot removers. Do not use cleaners that contain silicone or wax-based products. Cleaners containing these solvents can permanently change the appearance and feel of leather or soft trim and are not recommended.
Do not use cleaners that increase gloss, especially on the instrument panel. Reflected glare can decrease visibility through the windshield under certain conditions.
Vehicle Care
10-105
{ Caution
Use of air fresheners may cause permanent damage to plastics and painted surfaces. If an air freshener comes in contact with any plastic or painted surface in the vehicle, blot immediately and clean with a soft cloth dampened with a mild soap solution. Damage caused by air fresheners would not be covered by the vehicle warranty.
Cargo Cover and Convenience Net Wash with warm water and mild detergent. Do not use chlorine bleach. Rinse with cold water, and then dry completely.
{ Caution
Do not attach a device with a suction cup to the display. This may cause damage and would not be covered by the warranty.
Instrument Panel, Leather, Vinyl, Other Plastic Surfaces, Low Gloss Paint Surfaces and Natural Open Pore Wood Surfaces Use a soft microfiber cloth dampened with water to remove dust and loose dirt. For a more thorough cleaning, use a soft microfiber cloth dampened with a mild soap solution.
{ Caution
Soaking or saturating leather, especially perforated leather, as well as other interior surfaces,
(Continued)
Chevrolet Malibu Owner Manual 6081487) - 2014 - CRC - 11/19/13
(GMNA-Localizing-U.S./Canada/Mexico-
Black plate (106,1)
10-106
Vehicle Care
Care of Safety Belts Keep belts clean and dry. { Warning
Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Floor Mats
{ Warning
If a floor mat is the wrong size or is not properly installed, it can interfere with the pedals. Interference with the pedals can cause unintended acceleration and/or increased stopping distance which can cause a crash and injury. Make sure the floor mat does not interfere with the pedals.
Use the following guidelines for proper floor mat usage:
The original equipment floor mats were designed for your vehicle. If the floor mats need replacing, it is recommended that GM certified floor mats be purchased. Non-GM floor mats may not fit properly and may interfere with the pedals. Always check that the floor mats do not interfere with the pedals. . Use the floor mat with the
correct side up. Do not turn it over.
. Do not place anything on top of
the driver side floor mat.
