2016 Chevrolet Impala Owners Manual

Wiper Parking If the ignition is turned to LOCK/ OFF while the wipers are on LO, HI, or INT, they will immediately stop. If the windshield wiper lever is then moved to off before the driver door is opened or within 10 minutes, the wipers will restart and move to the base of the windshield.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

107

If the ignition is turned to LOCK/ OFF while the wipers are performing wipes due to windshield washing, the wipers continue to run until they reach the base of the windshield.

Compass The vehicle may have a compass display on the Driver Information Center (DIC). The compass receives its heading and other information from the Global Positioning System (GPS) antenna, StabiliTrak®, and vehicle speed information. The compass system is designed to operate for a certain number of miles or degrees of turn before needing a signal from the GPS satellites. When the compass display shows CAL, drive the vehicle for a short distance in an open area where it can receive a GPS signal. The compass system will automatically determine when a GPS signal is restored and provide a heading again. See Compass

Messages 0 130 for the messages that may be displayed for the compass.

Clock (Base Radio)

Setting the Time and Date To set the time or date: 1. Select SETTINGS from the

Home Page, then select Time and Date Settings.

2. Select the desired function. 3. Turn the MENU knob to

increase or decrease the value. 4. Press the MENU knob to go to

the next value. After the last value is selected the system will update and return to the SETTINGS menu. Press q BACK to go to the last menu and save the changes.

To set the Auto Set: 1. Select Settings from the Home

Page, then select Time and Date Settings.

2. Select Auto Set.

3. Press the faceplate button just

below Auto Set to turn it on or off.

Press q BACK to go to the last menu and save the changes. Auto Set requires an OnStar subscription. If Auto Set is on, the time displayed on the clock may not update immediately when driving into a new time zone. To set the clock display: 1. Select Settings from the Home

Page, then select Time and Date Settings.

2. Select Clock Display. 3. Turn the MENU knob to Off

or On.

4. Press the MENU knob to

select.

Press q BACK to go to the last menu and save the changes.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

108

Instruments and Controls

Clock (Uplevel Radio)

Power Outlets

Setting the Time and Date To set the time or date: 1. Select Settings from the Home

Page, then select Time and Date Settings.

2. Select the desired function. To set the time or date, press « or ª to change the hour, minutes, AM, or PM. To change the 12-24Hr setting, press the 12-24Hr button. To turn Auto Set on and off, press the Auto Set screen button. Auto Set requires an OnStar subscription. If Auto Set is on, the time displayed on the clock may not update immediately when driving into a new time zone. Press q BACK to go to the last menu and save the changes or { to return to the Home Page.

Power Outlets 12 Volt Direct Current The accessory power outlets can be used to plug in electrical equipment, such as a cell phone or MP3 player. There are three accessory power outlets:

Inside the front storage area below the climate control system. Inside the center console. . On the rear of the center

console.

The outlet is powered when the ignition is in ON/RUN or ACC/ ACCESSORY, or until the driver door is opened within 10 minutes of turning off the vehicle. See Retained Accessory Power (RAP) 0 208. Open the protective cover to use the accessory power outlet.

Certain electrical accessories may not be compatible with the accessory power outlets and could overload vehicle or adapter fuses. If there is a problem, see your dealer. When adding electrical equipment, be sure to follow the installation instructions included with the equipment. See Add-On Electrical Equipment 0 246.

Caution

Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords.

Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 amps rating.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Power Outlet 110/120 Volt Alternating Current The vehicle may have a power outlet that can be used to plug in electrical equipment that uses a maximum limit of 150 watts.

The power outlet is on the rear of the center console. An indicator light on the outlet turns on to show it is in use. The light comes on when the ignition is in ON/RUN and equipment requiring less than 150 watts is plugged into the outlet, and no system fault is detected.

Instruments and Controls

109

The indicator light does not come on if the ignition is in LOCK/OFF; if no equipment is plugged into the outlet; or if the equipment is plugged in, but not fully seated in the outlet. If equipment is connected using more than 150 watts or a system fault is detected, the equipment may operate briefly then turn off. A protection circuit shuts off the power supply and the indicator light turns off. To reset the circuit, unplug the item and plug it back in or turn the Retained Accessory Power (RAP) off and then back on. See Retained Accessory Power (RAP) 0 208. The power restarts when equipment using 150 watts or less is plugged into the outlet and a system fault is not detected. The power outlet is not designed for and may not work properly, if the following are plugged in: . Equipment with high initial peak

wattage, such as compressor-driven refrigerators and electric power tools.

. Other equipment requiring an

extremely stable power supply, such as microcomputer-controlled electric blankets or touch sensor lamps.

. Medical equipment.

Wireless Charging The vehicle may have wireless charging in the storage bin under the radio. See Center Console Storage 0 100. The system wirelessly charges one PMA or Qi compatible mobile device. To check for phone or other device compatibility, see www.gmtotalconnect.com. { Warning

Wireless charging can affect the operation of an implanted pacemaker or other medical devices. If you have one, it is recommended to consult with your doctor before using the wireless charging system.

3. The ~ will display on the V

on the infotainment screen. This indicates that the mobile device is properly positioned and charging. If a phone is placed on the charging pad and ~ does not display, remove the phone from the pad, and wait three seconds before placing/aligning the phone on the pad again.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

110

Instruments and Controls

The vehicle must be in ON/RUN, ACC/ACCESSORY, or Retained Accessory Power (RAP). The wireless charging feature may not correctly indicate charging when the vehicle is in RAP. See Retained Accessory Power (RAP) 0 208. The operating temperature is -20 °C (-4 °F) to 60 °C (140 °F) for the charging system and 0 °C (32 °F) to 35 °C (95 °F) for the phone. { Warning

Remove all metal objects from the charging pad before charging your mobile device. Metal objects, such as coins, keys, rings, or paper clips, between the phone and charging pad will become very hot. On the rare occasion that the charging system does not detect a metal object, and the object gets wedged between the phone and charger, remove the phone and allow the metallic object to cool before removing it from the charging pad, to prevent burns.

To charge a mobile device: 1. Remove all objects from the

charging pad. The system may not charge if there are any objects on the charging pad. 2. Place the mobile device face up on the @ symbol on the charging pad.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

111

Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Some warning lights come on briefly when the engine is started to indicate they are working. When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Waiting to do repairs can be costly and even dangerous.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

112

Instruments and Controls

Instrument Cluster

English Shown, Metric Similar

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

113

English Stop/Start Shown, Metric Similar

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

114

Instruments and Controls

Cluster Menu There is an interactive display area in the center of the instrument cluster.

Info app. This is where you can view the selected Driver Information Center (DIC) displays. See Driver Information Center (DIC) 0 127.

. Audio . Phone . Navigation . Settings

Audio In the main view of the Audio app, press w or x to scroll through radio stations or move to the next/ previous track of a CD/USB/ Bluetooth device that is connected to the vehicle. Press V to select the Audio app, then press p to enter the Audio menu. In the Audio menu browse for music, select from the favorites, or change the audio source.

Phone

Press V to select the Phone app, then press p to enter the Phone menu. In the Phone menu, if there is

Use the right steering wheel control to open and scroll through the different items and displays. Press o to access the cluster applications. Use w or x to scroll through the list of available applications. Not all applications will be available on all vehicles.

no active phone call, view recent calls, scroll through contacts, or select from the favorites. If there is an active call, mute or unmute the phone or switch to handset or handsfree operation.

Navigation

Press V to select the Navigation app, then press p to enter the Navigation menu. If there is no active route, you can resume the last route, location details, and turn the voice prompts on/off. If there is an active route, press V to cancel route guidance or turn the voice prompts on/off.

Settings

Press V to select the Settings app. Use w or x to scroll through the items in the Settings menu. Units : Press p while Units is displayed to enter the Units menu. Choose English or metric units by pressing V while the desired item is highlighted.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

115

Info Pages : Press p while Info Pages is displayed to enter the Info Pages menu and select the items to be displayed in the Info App. See Driver Information Center (DIC) 0 127. Speed Warning : The Speed Warning display allows the driver to set a speed that they do not want to exceed. To set the Speed Warning, press p when Speed Warning is displayed. Press w or x to adjust the value. Press V to set the speed. Once the speed is set, this feature can be turned off by pressing V while viewing this page. If the selected speed limit is exceeded, a pop-up warning is displayed with a chime. Compass : In certain vehicles the compass setting will allow for manually setting the compass. The user can set the zone and calibrate the compass. This setting page is only available on vehicles that are equipped with Remote Compass Module.

Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph).

Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles.

Trip Odometer The trip odometer shows how far the vehicle has been driven since the trip odometer was last reset. The trip odometer is accessed and reset through the Driver Information Center (DIC). See Driver Information Center (DIC) 0 127.

Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). For vehicles with the Stop/Start system, when the ignition is in ON/ RUN, the tachometer indicates the

vehicle status. When pointing to AUTO STOP, the engine is off but the vehicle is on and can move. The engine could auto start at any time. When the indicator points to OFF, the vehicle is off. When the engine is on, the tachometer will indicate the engine’s revolutions per minute (rpm). The tachometer may vary by several hundred rpm’s, during auto stop mode, when the engine is shutting off and restarting. A slight bump may be felt when the transmission is determining the most fuel efficient operating range.

Caution

If the engine is operated with the rpm’s in the warning area at the high end of the tachometer, the vehicle could be damaged, and the damage would not be covered by the vehicle warranty. Do not operate the engine with the rpm’s in the warning area.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

116

Instruments and Controls

Fuel Gauge

Metric

English

When the ignition is on, the fuel gauge indicates about how much fuel is left in the tank. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. When the indicator nears empty, the low fuel light comes on. There is still a little fuel left, but the fuel tank should be filled soon. Here are four things that some owners ask about. None of these show a problem with the fuel gauge:

. At the service station, the fuel

pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. . The gauge moves a little while

turning a corner or speeding up. . The gauge takes a few seconds

to stabilize after the ignition is turned on, and goes back to empty when the ignition is turned off.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Engine Coolant Temperature Gauge

Instruments and Controls

117

Safety Belt Reminders

Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.

Metric

English

This gauge shows the engine coolant temperature. If the gauge pointer moves toward the shaded area, the engine is too hot. This reading indicates the same thing as the warning light. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible. See Engine Overheating 0 264 for more information.

When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

118

Instruments and Controls

Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System 0 75.

When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on. The front passenger safety belt reminder light and chime may turn on if an object is put on the seat such as a briefcase, handbag,

grocery bag, laptop, or other electronic device. To turn off the reminder light and/or chime, remove the object from the seat or buckle the safety belt.

Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System 0 69.

The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.

{ Warning

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

If there is a problem with the airbag system, a Driver Information Center (DIC) message may also come on. See Airbag System Messages 0 136.

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System 0 75 for important safety information. The passenger airbag status indicator is in the overhead console.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

119

outboard passenger frontal airbag and knee airbag are allowed to inflate. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag and knee airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ Warning

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light 0 118 for more information, including important safety information.

Charging System Light

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started. If the light stays on or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. When this light comes on, the Driver Information Center (DIC) also displays a message. See Battery Voltage and Charging Messages 0 130.

United States

Canada

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or the on or off symbol, to let you know the status of the front outboard passenger frontal airbag and knee airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the front

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

120

Instruments and Controls

If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

Malfunction Indicator Lamp (Check Engine Light) This light is part of the vehicle’s emission control on-board diagnostic system. If this light is on while the engine is running, a malfunction has been detected and the vehicle may require service. The light should come on to show that it is working when the ignition is in ON/RUN with the engine not running for Key Access or in Service Only Mode for Keyless Access. See Ignition Positions (Keyless Access) 0 201 or Ignition Positions (Key Access) 0 203.

Malfunctions are often indicated by the system before any problem is noticeable. Being aware of the light and seeking service promptly when it comes on may prevent damage.

Caution

If the vehicle is driven continually with this light on, the emission control system may not work as well, the fuel economy may be lower, and the vehicle may not run smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.

Caution

Modifications to the engine, transmission, exhaust, intake, or fuel system, or the use of replacement tires that do not meet the original tire specifications, can cause this light to come on. This could lead to

(Continued)

Caution (Continued)

costly repairs not covered by the vehicle warranty. This could also affect the vehicle’s ability to pass an Emissions Inspection/ Maintenance test. See Accessories and Modifications 0 249.

If the light is flashing : A malfunction has been detected that could damage the emission control system and increase vehicle emissions. Diagnosis and service may be required. To help prevent damage, reduce vehicle speed and avoid hard accelerations and uphill grades. If towing a trailer, reduce the amount of cargo being hauled as soon as possible. If the light continues to flash, find a safe place to park. Turn the vehicle off and wait at least 10 seconds before restarting the engine. If the light is still flashing, follow the

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

previous guidelines and see your dealer for service as soon as possible. If the light is on steady : A malfunction has been detected. Diagnosis and service may be required. Check the following: . A loose or missing fuel cap may cause the light to come on. See Filling the Tank 0 239. A few driving trips with the cap properly installed may turn the light off.

. Poor fuel quality can cause

inefficient engine operation and poor driveability, which may go away once the engine is warmed up. If this occurs, change the fuel brand. It may require at least one full tank of the proper fuel to turn the light off. See Fuel 0 237.

If the light remains on, see your dealer.

Instruments and Controls

121

Emissions Inspection and Maintenance Programs If the vehicle requires an Emissions Inspection/Maintenance test, the test equipment will likely connect to the vehicle's Data Link Connector (DLC).

The DLC is under the instrument panel to the left of the steering wheel. Connecting devices that are not used to perform an Emissions Inspection/Maintenance test or to service the vehicle may affect vehicle operation See Add-On Electrical Equipment 0 246. See your dealer if assistance is needed. The vehicle may not pass inspection if: . The light is on when the engine

is running.

. The light does not come on

when the ignition is in ON/RUN with the engine not running for Key Access or in Service Only Mode for Keyless Access.

. Critical emission control systems

have not been completely diagnosed. If this happens, the vehicle would not be ready for inspection and might require several days of routine driving before the system is ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down, or if the vehicle has been recently serviced.

See your dealer if the vehicle will not pass or cannot be made ready for the test.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

122

Instruments and Controls

vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

Metric

English

This light comes on briefly when the vehicle is turned on. If it does not come on then, have it fixed so it will be ready to warn if there is a problem. If the light comes on and stays on, there is a brake problem. { Warning

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system

(Continued)

Warning (Continued)

warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

Electric Parking Brake Light

Metric

English

This light comes on when the parking brake is applied. If the light continues flashing after the parking brake is released, or while driving, there is a problem with the Electric Parking Brake system or another system. A message may also display in the Driver Information Center (DIC). See Brake System Messages 0 130.

If the light does not come on, or remains flashing, see your dealer.

Service Electric Parking Brake Light

This light should come on briefly when starting the vehicle. If it does not come on, have it fixed so it will be ready to warn if there is a problem. If this light stays on, there is a problem with the Electric Parking Brake system or another system on the vehicle that is causing the parking brake system to work at a reduced level. The vehicle can still be driven, but should be taken to a dealer as soon as possible. See the information for the Electric Parking Brake under Parking Brake 0 214.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

123

If a message displays in the Driver Information Center (DIC), see Brake System Messages 0 130.

Antilock Brake System (ABS) Warning Light

This light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the light comes on while driving, stop as soon as it is safely possible and turn off the vehicle. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. A chime may also sound when the light comes on steady.

If the ABS light is the only light on, the vehicle has regular brakes, but the antilock brakes are not functioning. If both the ABS and the brake system warning light are on, the vehicle's antilock brakes are not functioning and there is a problem with the regular brakes. See your dealer for service. See Brake System Warning Light 0 121 and Brake System Messages 0 130.

Lane Departure Warning (LDW) Light

If equipped, this light comes on briefly while starting the vehicle. If it does not come on, have the vehicle serviced.

This light is green if LDW is on and ready to operate. This light changes to amber and flashes to indicate that the lane marking has been crossed without using a turn signal in that direction. See Lane Departure Warning (LDW) 0 235.

Vehicle Ahead Indicator

If equipped, this indicator will display green when a vehicle is detected ahead and amber when you are following a vehicle ahead much too closely. See Forward Collision Alert (FCA) System 0 230.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

124

Instruments and Controls

Traction Off Light

StabiliTrak® OFF Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control/Electronic Stability Control 0 216.

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If the StabiliTrak and TCS are off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control/Electronic Stability Control 0 216.

Traction Control System (TCS)/StabiliTrak® Light

This light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See Traction Control/Electronic Stability Control 0 216.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

125

Tire Pressure Light

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages 0 137. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure 0 290.

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation 0 293.

Engine Oil Pressure Light

Caution

Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil low can also damage the engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

This light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Low Fuel Warning Light

This light is near the fuel gauge and comes on briefly when the ignition is turned on as a check to show it is working.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

126

Instruments and Controls

It also comes on when the fuel tank is low on fuel. The light turns off when fuel is added. If it does not, have the vehicle serviced.

Security Light

The security light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation (Key Access) 0 43 or Immobilizer Operation (Keyless Access) 0 44.

High-Beam On Light

Cruise Control Light

This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer 0 149.

Lamps On Reminder

This light in the Driver Information Center (DIC) is white when the cruise control is on and ready, and turns green when the cruise control is set and active. See Cruise Control 0 218. Adaptive Cruise Control Light

This light comes on when the exterior lamps are in use. See Exterior Lamp Controls 0 148.

This light in the Driver Information Center (DIC) is white when the Adaptive Cruise Control (ACC) (if equipped) is on and ready, and

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

127

turns green when the ACC is set and active. See Adaptive Cruise Control 0 220.

Door Ajar Light

This light comes on in the Driver Information Center (DIC) when a door is open or not securely latched. Before driving, check that all doors are properly closed.

Information Displays

Driver Information Center (DIC) The DIC displays are shown in the center of the instrument cluster in the Info app. See Instrument Cluster 0 112. The Info app is only available when the vehicle is in ON/RUN. The displays show the status of many vehicle systems. The controls for the DIC are on the right steering wheel control.

w or x : Press to move up or down in a list, or on the main view press to cycle through the different Info app pages. o or p : Press o to open application menus on the left. Press p to open interaction menus on the right. V (Select/Reset) : Press to select a menu item. Press and hold to reset values on certain screens, or on the main view reset info pages to the original setting. DIC Info Page Options The info pages on the DIC can be turned on or off through the Settings app. 1. Press o to access the cluster

applications.

2. Press w or x to scroll to the

Settings application.

3. Press V to select the

Settings app.

4. Scroll to Info Pages and

press p.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

128

Instruments and Controls

5. Select Edit List. 6. Press w or x to move

through the list of possible information displays.

7. Press V while an item is

highlighted to select or deselect that item. When an item is selected, a checkmark will appear next to it.

DIC Info Pages The following is the list of all possible DIC info page displays. Some may not be available for your particular vehicle. Some items may not be turned on by default but can be turned on through the Settings app. See “DIC Info Page Options” earlier in this section. Current Speed : Displays the vehicle speed in either kilometers per hour (km/h) or miles per hour (mph). Trip A and Average Fuel Economy or Trip B and Average Fuel Economy : The Trip display shows the current distance traveled, in

either kilometers (km) or miles (mi), since the trip odometer was last reset. The Average Fuel Economy display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the approximate average fuel economy that the vehicle has right now, and will change as driving conditions change. This number is calculated based on the number of L/ 100 km (mpg) recorded since the last time this menu item was reset. The Average Fuel Economy and trip odometer can be reset together by pressing and holding V while this display is active. Fuel Range : Displays the approximate distance the vehicle can be driven without refueling. LOW will be displayed when the vehicle is low on fuel. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank.

Average Speed : Displays the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing and holding V while this display is active.

Timer : To start the timer, press V while this display is active. The display will show the amount of time that has passed since the timer was last reset. To stop the timer, press V briefly while this display is active and the timer is running. To reset the timer to zero, press and hold V while this display is active. Oil Life : Displays an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages 0 132.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

The oil should be changed as soon as possible. See Engine Oil 0 255. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule. See Maintenance Schedule 0 325. The Oil Life display must be reset after each oil change. It will not reset itself. Do not reset the Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, press and hold V for several seconds while the Oil Life display is active. See Engine Oil Life System 0 257. Coolant Temperature : Displays the coolant temperature in either degrees Celsius (°C) or degrees Fahrenheit (°F).

Instruments and Controls

129

Tire Pressure : Displays the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). If the pressure is low, the value for that tire is shown in amber. See Tire Pressure Monitor System 0 292 and Tire Pressure Monitor Operation 0 293. Battery Voltage : Displays the current battery voltage. The battery voltage can fluctuate while viewing this information on the DIC. This is normal. Speed Signs : Displays sign information, which comes from a roadway database in the onboard navigation.

Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may appear one after another. The messages that do not require immediate action can be acknowledged and cleared by pressing V.

The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously; clearing the message does not correct the problem. The following are the possible messages and some information about them.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

130

Instruments and Controls

Battery Voltage and Charging Messages

BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery - North America 0 268. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.

Brake System Messages

BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid 0 267. PARK BRAKE RELEASED This message is displayed when the parking brake is released. PARK BRAKE SET This message is displayed when the parking brake is set. RELEASE PARKING BRAKE This message is displayed if the Electric Parking Brake is on while the vehicle is in motion. See Parking Brake 0 214. SERVICE BRAKE ASSIST This message may be displayed when there is a problem with the brake boost assist system. When this message is displayed, the brake boost assist motor might be heard operating and you might notice pulsation in the brake pedal. This is

normal under these conditions. Take the vehicle to your dealer for service. SERVICE PARKING BRAKE This message is displayed when there is a problem with the parking brake. Take the vehicle to your dealer for service. STEP ON BRAKE TO RELEASE PARK BRAKE This message is displayed if you attempt to release the Electric Parking Brake without the brake pedal applied. See Parking Brake 0 214.

Compass Messages Dashes may be displayed if the vehicle temporarily loses communication with the Global Positioning System (GPS).

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Cruise Control Messages

ADAPTIVE CRUISE SET TO XXX This message displays when the Adaptive Cruise Control (ACC) speed is set. See Adaptive Cruise Control 0 220. ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE This message displays when attempting to activate Adaptive Cruise Control (ACC) when it is temporarily unavailable. The ACC system does not need service. This can occur under the following conditions: . Cruise is turned on when the

vehicle is stopped.

. The radar can't see objects well.

See next message.

FRONT RADAR BLOCKED — SEE OWNER MANUAL This message can occur under the following conditions:

Instruments and Controls

131

. The radar is not clean. Keep the radar sensors free of mud, dirt, snow, ice, and slush. Clean the entire front and/or rear of the vehicle. For cleaning instructions, see Exterior Care 0 315.

. Heavy rain or snow is interfering with the radar object detection or camera performance. CRUISE SET TO XXX This message displays when the cruise control speed is set. See Cruise Control 0 218. NO CRUISE BRAKING GAS PEDAL APPLIED This message displays when Adaptive Cruise Control (ACC) is active and the driver is pressing the gas pedal. When this occurs, ACC will not brake. See Adaptive Cruise Control 0 220.

SERVICE ADAPTIVE CRUISE CONTROL This message displays when the Adaptive Cruise Control (ACC) needs service. Take the vehicle to your dealer. SHIFT TO PARK BEFORE EXITING This message may display if Adaptive Cruise Control (ACC) is engaged holding the vehicle at a stop, and the driver attempts to exit the vehicle. Put the vehicle in P (Park) before exiting.

Door Ajar Messages

DOOR OPEN A door open symbol will display on the DIC showing which door is open. If the vehicle has been shifted out of P (Park), a DOOR OPEN message will also be displayed. If the shift lever is in M (Manual Mode), the DOOR OPEN message will display if the vehicle starts to move. Close the door completely.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

132

Instruments and Controls

HOOD OPEN This message will display along with a hood open symbol when the hood is open. Close the hood completely. TRUNK OPEN This message will display along with a symbol when the trunk is open. Close the trunk completely.

Engine Cooling System Messages

A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. The vehicle can continue to be driven.

If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be

sure to reset the oil life system. See Engine Oil Life System 0 257, Driver Information Center (DIC) 0 127, Engine Oil 0 255, and Maintenance Schedule 0 325. ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OIL LOW — ADD OIL On some vehicles, this message displays when the engine oil level may be too low. Check the oil level before filling to the recommended level. If the oil is not low and this message remains on, take the vehicle to your dealer for service. See Engine Oil 0 255. OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

133

corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.

Engine Power Messages

ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible.

TIGHTEN GAS CAP This message displays when the fuel cap is not on tight. Tighten the fuel cap.

Key and Lock Messages

NO REMOTE DETECTED This message displays when trying to start the vehicle if an RKE transmitter is not detected. The transmitter battery may be weak. See “Starting the Vehicle with a Low Transmitter Battery or Wireless Interference” under Remote Keyless Entry (RKE) System Operation 0 30. NO REMOTE PRESS BRAKE TO RESTART This message is displayed if the remote is no longer detected in the vehicle. Press the brake pedal to restart the vehicle. NUMBER OF KEYS PROGRAMMED This message displays when programming new keys to the vehicle.

REMOTE LEFT IN VEHICLE This message displays when leaving the vehicle with the RKE transmitter still inside. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the RKE transmitter needs to be replaced. USE TRANSMITTER POCKET TO START This message displays when the transmitter needs to be placed in the transmitter pocket to start the vehicle. See “Starting the Vehicle with a Low Transmitter Battery or Wireless Interference” under Remote Keyless Entry (RKE) System Operation 0 30.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

134

Instruments and Controls

Lamp Messages

AUTOMATIC LIGHT CONTROL ON/OFF This message is displayed when the automatic light control has been turned on or off. See Automatic Headlamp System 0 150. XX TURN INDICATOR FAILURE When one of the turn signals is out, this message displays to show which bulb needs to be replaced. See Bulb Replacement 0 271 and Replacement Bulbs 0 275. TURN SIGNAL ON This message is displayed if the turn signal has been left on. Turn off the turn signal.

Object Detection System Messages

AUTOMATIC COLLISION PREP OFF This message displays when the Front Automatic Braking (FAB) System has been turned off. See Front Automatic Braking (FAB) System 0 232. AUTOMATIC COLLISION PREP REDUCED This message displays when the Front Automatic Braking (FAB) System has been set to the Alert setting. This setting disables most FAB functions. Some last-second automatic braking capability is still provided with the Alert setting, but braking is less likely to occur. See Front Automatic Braking (FAB) System 0 232. AUTOMATIC COLLISION PREPARATION UNAVAILABLE This message displays when the Front Automatic Braking (FAB) System has been unavailable for

some time. The FAB System does not need service. This message can display under the following conditions: . The front of the vehicle or

windshield is not clean. Keep these areas clean and free of mud, dirt, snow, ice, and slush. For cleaning instructions, see Exterior Care 0 315.

. Heavy rain or snow is interfering

with the object detection performance.

This message may also be displayed if there is a problem with the StabiliTrak system. See Traction Control/Electronic Stability Control 0 216. FORWARD COLLISION ALERT OFF This message displays when the Forward Collision Alert has been turned off.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

135

FRONT CAMERA BLOCKED CLEAN WINDSHIELD This message displays when the camera is blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. The Lane Departure Warning system will not operate. Forward Collision Alert (FCA) may not work or may not work as well. LANE CHANGE ALERT OFF This message indicates that the driver has turned the Side Blind Zone Alert (SBZA) and Lane Change Alert (LCA) systems off. LANE DEPARTURE WARNING UNAVAILABLE This message displays when attempting to activate the Lane Departure Warning (LDW) system when it is temporarily unavailable. The LDW system does not need service.

This message could be due to the camera being blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. PARK ASSIST OFF This message displays when the Parking Assist system has been turned off or when there is a temporary condition causing the system to be disabled. REAR CROSS TRAFFIC ALERT OFF This message displays when the Rear Cross Traffic Alert has been turned off. SERVICE AUTOMATIC COLLISION PREP If this message displays, take the vehicle to your dealer to repair the system. Adaptive Cruise Control (ACC), Forward Collision Alert (FCA), and/or the Front Automatic Braking (FAB) System may not work. Do not use these systems until the vehicle has been repaired.

SERVICE FRONT CAMERA If this message remains on after continued driving, the vehicle needs service. Do not use the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) features. Take the vehicle to your dealer. SERVICE PARKING ASSIST This message displays if there is a problem with the Parking Assist system. Do not use this system to help you park. See your dealer for service. SERVICE SIDE DETECTION SYSTEM If this message remains on after continued driving, the vehicle needs service. Side Blind Zone Alert (SBZA), Lane Change Alert (LCA), and Rear Cross Traffic Alert (RCTA) features will not work. Take the vehicle to your dealer.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

136

Instruments and Controls

SIDE DETECTION SYSTEM UNAVAILABLE This message indicates that Side Blind Zone Alert (SBZA), Lane Change Alert (LCA), and Rear Cross Traffic Alert (RCTA) are disabled either because the sensor is blocked and cannot detect vehicles in the blind zone, or the vehicle is passing through an open area, such as the desert, where there is insufficient data for operation. This message may also activate during heavy rain or due to road spray. The vehicle does not need service. For cleaning, see "Washing the Vehicle" under Exterior Care 0 315.

Ride Control System Messages

SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message

still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive; however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly.

Airbag System Messages

SERVICE AIRBAG This message displays if there is a problem with the airbag system. See your dealer for service.

Security Messages

THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.

Service Vehicle Messages

SERVICE POWER STEERING This message displays and a chime may sound when there may be a problem with the power steering system. If this message displays and a reduction in steering

performance or loss of power steering assistance is noticed, see your dealer. SERVICE VEHICLE SOON This message is displayed if there is a problem with the vehicle. Take the vehicle to your dealer for service.

Starting the Vehicle Messages

PRESS BRAKE TO START VEHICLE This message is displayed when attempting to start the vehicle without first pressing the brake pedal. SERVICE KEYLESS START SYSTEM This message is displayed if there is a problem with the pushbutton start system. Take the vehicle to your dealer for service.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

137

See Tires 0 283, Vehicle Load Limits 0 198, and Tire Pressure 0 290. More than one tire pressure message can be received at a time. The DIC also shows the tire pressure values. See Driver Information Center (DIC) 0 127.

Transmission Messages

SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT DENIED This message displays when using the Driver Shift Control (DSC) and attempting to shift to a gear not appropriate for the vehicle speed and engine revolutions per minute (rpm). See Manual Mode 0 212.

SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when turning the ignition off if the vehicle is not in P (Park). TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Vehicle Reminder Messages

ICE POSSIBLE DRIVE WITH CARE This message is displayed when ice conditions are possible.

Tire Messages

SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation 0 293. TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation 0 293. TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. The low tire pressure warning light will also come on. See Tire Pressure Light 0 125. If a tire pressure message displays, inflate the tires until the tire pressure is equal to the values shown on the Tire and Loading Information label.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

138

Instruments and Controls

TURN WIPER CONTROL TO INTERMITTENT FIRST This message is displayed when attempting to adjust the intermittent wiper speed without intermittent selected on the wiper control. See Windshield Wiper/Washer 0 106.

Vehicle Speed Messages

SPEED LIMIT EXCEEDED This message is displayed when the vehicle speed is greater than the speed warning speed. See "Speed Warning" under Instrument Cluster 0 112. SPEED LIMIT SET TO XXX This message is displayed when the speed warning is set. See "Speed Warning" under Instrument Cluster 0 112.

Washer Fluid Messages

WASHER FLUID LOW ADD FLUID This message may display when the washer fluid level is low. Fill the windshield washer reservoir as soon as possible. See Engine Compartment Overview 0 252 for the location of the windshield washer reservoir. Also, see Washer Fluid 0 265.

Window Messages

OPEN, THEN CLOSE DRIVER/ PASSENGER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to program each front window for the express-up feature to work. See Power Windows 0 47.

Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features.

Base Radio Audio System Controls To access the personalization menus: 1. On the Home page, turn the

MENU knob to highlight Settings and press the MENU knob.

2. Turn the MENU knob to

highlight the desired feature and press the MENU knob to display a list of available options.

3. Turn the MENU knob to scroll

through and highlight the desired option, then press the MENU knob.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

4. Turn the MENU knob to

highlight the desired option setting and press the MENU knob.

5. Press q BACK to return to the

previous menu.

Uplevel Radio Audio System Controls To access the personalization menus: 1. Press SETTINGS on the Home

page on the infotainment system display.

2. Press the desired feature to

display a list of available options.

3. Press the desired option. 4. Press to select the desired

option setting.

5. Press q BACK to return to the

previous menu.

Personalization Menus The following list of features may be available: . Time and Date

Instruments and Controls

139

. Language (Language) . Valet Mode . Radio . Vehicle . Bluetooth . Voice . Display . Rear Camera . Return to Factory Settings . Software Information Each menu is detailed in the following information. Time and Date Manually set the time and date. See Clock (Base Radio) 0 107 or Clock (Uplevel Radio) 0 108. Language (Language) Select Language, then select from the available language(s).

Valet Mode (If Equipped) This will lock the infotainment system and steering wheel controls. It may also limit access to vehicle storage locations (if equipped). To enable valet mode: 1. Enter a four-digit code on the

keypad.

2. Select Enter to go to the

confirmation screen.

3. Re-enter the four-digit code. Press LOCK or UNLOCK to lock or unlock the system. Press Back to go back to the previous menu. Radio To manage the radio features, see “Radio Setup” under “Setting Radio Preferences” in Home Page 0 158. Vehicle Select and the following may display: . Climate and Air Quality . Collision/Detection Systems . Comfort and Convenience

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

140

Instruments and Controls

. Lighting . Power Door Locks . Remote Lock, Unlock, Start

Climate and Air Quality Select and the following may display: . Auto Fan Max Speed . Air Conditioning Mode . Auto Defog . Auto Rear Defog

Auto Fan Max Speed This feature will set the maximum auto fan speed. Select Low, Medium, or High.

Air Conditioning Mode This feature changes the mode of the air conditioning. Select Off, On, or Last Setting.

Auto Defog When set to On, the front defog will automatically react to temperature and humidity conditions that may

cause fogging. Only vehicles with the dual automatic climate control will have this option. Select Off or On.

Auto Rear Defog If equipped, this allows the Auto Rear Defog to be turned on or off. This feature will automatically turn on the rear window defogger when it is cold outside. Select Off or On.

Collision/Detection Systems Select and the following may