You may also be interested in...
Download PDF Manual

10-48


Vehicle Care


Mini Fuse


58


59


61


62


63


64


65


Usage Body Control Module 2
Body Control Module 1
Spare Oxygen Sensor 2
(Post), EV Fan (Diesel) Spare Mass Air Flow/ Canister Vent Odd Ignition/ Injectors


Mini Fuse


Usage


Mini Fuse


Daytime Running Lamps 2
(LOLVL‐V22) (If Equipped) Daytime Running Lamps 1
(UPLVL+V22) (If Equipped) Auxiliary Stop Lamps Spare Spare Fuel Heater


66


67


68


69
70
71


72


73


75
76


77


78


79


Usage Body Control Module 6
Lighter/Data Link Connection V6 Fuel Injectors Spare Oxygen Sensor 2 (Pre) Engine Control Module Powertrain Even Ignition/ Injectors


Chevrolet Express Owner Manual - 2011


Black plate (49,1)


J‐Case Fuse


Usage


Relay


Usage


Relay


Usage


Vehicle Care


10-49


15
37
38
39


40


Run/Crank Spare Fuel Pump Crank Air Conditioning Compressor


48
49
50
57
60


Fan High Powertrain Spare Fan Low Fan Control


41
42
43
44


45


46
47
74


ABS Motor ABS Module Spare Trailer Wiring Fan High Starter Solenoid Engine Control Module/Powertrain Spare Fan Lo Front Blower


Chevrolet Express Owner Manual - 2011


Black plate (50,1)


10-50


Vehicle Care


Floor Console Fuse Block The floor console fuse block is located under the driver seat.


The vehicle may not be equipped with all of the fuses, relays, and features shown.


Chevrolet Express Owner Manual - 2011


Black plate (51,1)


Vehicle Care


10-51


Mini‐Fuse


Usage


Mini‐Fuse


Usage


Mini‐Fuse


Usage


F1


F2


F3


F4
F5


F6


F7


F8


F9


F10


Empty Steering Wheel Sensor Auxiliary Parking Lamps (Cut‐Away) Front Park Lamps Trailer Park Lamps Upfitter Park Lamps Right Rear Park Lamp Left Rear Park Lamp Outside Rear View Mirror Switch Airbag/Automatic Occupant Sensing


F11


F12


F13


F14


F15


F17


F18


F19


F20


OnStar® (If Equipped) Empty Heating, Ventilation and Air Conditioning 2
Heating, Ventilation and Air Conditioning 1
Empty Outside Rear View Mirror Heater Rear Window Defogger Compass Radio/Chime/XM™ Satellite Radio (If Equipped)


F21


F22


F23


F25


F26


F27


F30


Remote Function Actuator/Tire Pressure Monitor Ignition Switch/ Discrete Logic Ignition Sensor (PK3) Instrument Panel Cluster Heating, Ventilation and Air Conditioning Control Auxiliary/Trailer Backup Taillamps Backup Upfitter Courtesy Lamps


Chevrolet Express Owner Manual - 2011


Black plate (52,1)


10-52


Vehicle Care


Mini‐Fuse


Usage


Relays


Usage


F31
F32
F33


F34


F35


F36
F37
F38


Front Door Lock Rear Door Lock Cargo Door Unlock Passenger Door Unlock Rear Passenger Door Unlock Driver Door Unlock Empty Empty


J‐Case Fuse


Usage


F16
F24


F28


F29


Upfitter Auxiliary 1
Empty Upfitter Auxiliary 2
Reading Lamps Rear Blower


K1


K2


K3


K4


K5


K6


Run (High Current Micro) Empty (High Current Micro) Park Lamps (High Current Micro) Upfitter Auxiliary 2
(High Current Mini) Rear Defogger (High Current Micro) Retained Accessory Power (RAP) (High Current Micro)


Circuit Breaker


CB1
CB2


Usage


Power Seats Power Windows


Wheels and Tires


Tires Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer.


{ WARNING . Poorly maintained and


improperly used tires are dangerous.


. Overloading the tires can


cause overheating as a result of too much flexing. There could be a blowout and a serious crash. See Vehicle Load Limits on page 9‑12.


(Continued)


Chevrolet Express Owner Manual - 2011


Black plate (53,1)


Vehicle Care


10-53


WARNING (Continued)


WARNING (Continued)


. Underinflated tires pose the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when the tires are cold.


. Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when hitting a pothole. Keep tires at the recommended pressure.


. Worn or old tires can cause a


crash. If the tread is badly worn, replace them.


. Replace any tires that have been damaged by impacts with potholes, curbs, etc.


(Continued)


. Improperly repaired tires can


cause a crash. Only the dealer or an authorized tire service center should repair, replace, dismount, and mount the tires.


. Do not spin the tires in


excess of 55 km/h (35 mph) on slippery surfaces such as snow, mud, ice, etc. Excessive spinning may cause the tires to explode.


Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The examples show a typical passenger vehicle and light truck tire sidewall.


Passenger (P‐Metric) Tire (A) Tire Size: The tire size code is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail.


Chevrolet Express Owner Manual - 2011


Black plate (54,1)


10-54


Vehicle Care


(B) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. (C) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards.


(D) Tire Identification Number (TIN): The letters and numbers following the DOT code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.


(F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information, see Uniform Tire Quality Grading on page 10‑72. (G) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommended tire pressure see Tire Pressure on page 10‑60 and Vehicle Load Limits on page 9‑12.


Chevrolet Express Owner Manual - 2011


Black plate (55,1)


Vehicle Care


10-55


(D) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. (E) Tire Identification Number (TIN): The letters and numbers following the DOT code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.


(B) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. This does not apply to Goodyear LT225/75R16
G949 RSA and Goodyear LT225/75R16 G933 RSD commercial truck tires. (C) Dual Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used in a dual configuration. For information on recommended tire pressure see Tire Pressure on page 10‑60
andVehicle Load Limits on page 9‑12.


Light Truck (LT-Metric) Tire


(A) Tire Size: The tire size code is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail.


Chevrolet Express Owner Manual - 2011


Black plate (56,1)


10-56


Vehicle Care


(F) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (G) Single Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used as a single. For information on recommended tire pressure see Tire Pressure on page 10‑60 and Vehicle Load Limits on page 9‑12.


Tire Designations


Tire Size The following examples show the different parts of a tire size.


Passenger (P‐Metric) Tire


(A) Passenger (P‐Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association.


(B) Tire Width: The three‐digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio: A two‐digit number that indicates the tire height‐to‐width measurements. For example, if the tire size aspect ratio is 75, as shown in item C of the illustration, it would mean that the tire's sidewall is 75 percent as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted‐bias ply construction.


Chevrolet Express Owner Manual - 2011


Black plate (57,1)


(E) Rim Diameter: Diameter of the wheel in inches. (F) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.


Light Truck (LT‐Metric) Tire


(A) Light Truck (LT‐Metric) Tire: The United States version of a metric tire sizing system. The letters LT as the first two characters in the tire size mean a light truck tire engineered to standards set by the U.S. Tire and Rim Association.


(B) Tire Width: The three‐digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio: A two‐digit number that indicates the tire height‐to‐width measurements. For example, if the tire size aspect ratio is 75, as shown in item C of the light truck (LT‐Metric) tire illustration, it would mean that the tire's sidewall is 75 percent as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted‐bias ply construction.


Vehicle Care


10-57


(E) Rim Diameter: Diameter of the wheel in inches. (F) Load Range: Load Range. (G) Service Description: The service description indicates the load index and speed rating of a tire. If two numbers are given as in the example, 120/116, then this represents the load index for single versus dual wheel usage (single/dual). The speed rating is the maximum speed a tire is certified to carry a load. This does not apply to Goodyear LT225/75R16 G949 RSA and Goodyear LT225/75R16
G933 RSD commercial truck tires; see the dual tire and single tire maximum load and load range letter designations on the tire sidewall.


Chevrolet Express Owner Manual - 2011


Black plate (58,1)


10-58


Vehicle Care


Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight: The combined weight of optional accessories. Some examples of optional accessories are automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials.


Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in kPa (kilopascal) or psi (pounds per square inch) before a tire has built up heat from driving. See Tire Pressure on page 10‑60. Curb Weight: The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo.


DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR: Gross Vehicle Weight Rating. See Vehicle Load Limits on page 9‑12. GAWR FRT: Gross Axle Weight Rating for the front axle. See Vehicle Load Limits on page 9‑12. GAWR RR: Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits on page 9‑12.


Chevrolet Express Owner Manual - 2011


Black plate (59,1)


Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT‐Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279
that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire.


Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lbs). See Vehicle Load Limits on page 9‑12. Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire.


Vehicle Care


10-59


Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure on page 10‑60
andVehicle Load Limits on page 9‑12. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead.


Chevrolet Express Owner Manual - 2011


Black plate (60,1)


10-60


Vehicle Care


Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1.6 mm (1/16 in) of tread remains. See When It Is Time for New Tires on page 10‑68. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire's traction, temperature, and treadwear.


Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 10‑72. Vehicle Capacity Weight: The number of designated seating positions multiplied by 68 kg (150 lbs) plus the rated cargo load. See Vehicle Load Limits on page 9‑12. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle capacity weight and the original equipment tire size and recommended inflation pressure.


See “Tire and Loading Information Label” under Vehicle Load Limits on page 9‑12.


Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:


. Tire overloading and


overheating which could lead to a blowout.


. Premature or


irregular wear. . Poor handling. . Reduced fuel economy.


Chevrolet Express Owner Manual - 2011


Black plate (61,1)


Overinflated tires, or tires that have too much air, can result in:


. Unusual wear. . Poor handling. . Rough ride. . Needless damage from


road hazards.


The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures. The recommended pressure is the minimum air pressure needed to support the vehicle's maximum load carrying capacity. For additional information regarding how much weight the vehicle can carry, and an example of the Tire and Loading Information label, see Vehicle Load Limits on page 9‑12.


How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.


When to Check Check the tires once a month or more. Do not forget the spare tire, if the vehicle has one. SeeFull-Size Spare Tire on page 10‑88 for additional information.


How to Check Use a good quality pocket-type gauge to check tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi).


Vehicle Care


10-61


Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air. Re-check the tire pressure with the tire gauge. Return the valve caps on the valve stems to prevent leaks and keep out dirt and moisture.


Chevrolet Express Owner Manual - 2011


Black plate (62,1)


10-62


Vehicle Care


Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a


low tire pressure telltale when one or more of your tires is significantly under‐inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under‐inflated tire causes the tire to overheat and can lead to tire failure. Under‐inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under‐inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.


The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start‐ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation on page 10‑63 for additional information.


Chevrolet Express Owner Manual - 2011


Black plate (63,1)


Federal Communications Commission (FCC) and Industry Canada See Radio Frequency Statement on page 13‑19 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310.


Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmit the tire pressure readings to a receiver located in the vehicle.


When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the Tire and Loading Information label. See Vehicle Load Limits on page 9‑12. A message to check the pressure in a specific tire displays in the Driver Information Center (DIC). The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. If the vehicle has DIC buttons, tire pressure levels can be viewed.


Vehicle Care


10-63


For additional information and details about the DIC operation and displays, see Driver Information Center (DIC) on page 5‑28 and Tire Messages on page 5‑40. The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and needs to be inflated to the proper pressure. A Tire and Loading Information label shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load Limits on page 9‑12, for an example of the Tire and Loading Information label and its location. Also see Tire Pressure on page 10‑60.


Chevrolet Express Owner Manual - 2011


Black plate (64,1)


10-64


Vehicle Care


The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection on page 10‑66, Tire Rotation on page 10‑66 and Tires on page 10‑52. Notice: Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use only the GM-approved tire sealant available through your dealer or included in the vehicle.


TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire pressure warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message also displays. The malfunction light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause these to come on are: . One of the road tires has been


replaced with the spare tire. The spare tire does not have a TPMS sensor. The malfunction light and the DIC message should go off after the road tire is replaced and the sensor matching process is performed successfully. See "TPMS Sensor Matching Process" later in this section.


The TPMS sensor matching process was not done or not completed successfully after rotating the tires. The malfunction light and the DIC message should go off after successfully completing the sensor matching process. See "TPMS Sensor Matching Process" later in this section. . One or more TPMS sensors


are missing or damaged. The malfunction light and the DIC message should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer for service.


. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended could prevent the TPMS from functioning properly. See Buying New Tires on page 10‑69.


Chevrolet Express Owner Manual - 2011


Black plate (65,1)


. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.


If the TPMS is not functioning properly, it cannot detect or signal a low tire condition. See your dealer for service if the TPMS malfunction light and DIC message come on and stay on. TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the vehicle’s tires or replacing one or more of the TPMS sensors. Also, the TPMS sensor matching process should be performed after replacing a spare tire with a road tire containing the TPMS sensor. The malfunction light and the DIC message should go off at the next ignition cycle. The sensors are matched to the tire/wheel positions,


using a TPMS relearn tool, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear. See your dealer for service or to purchase a relearn tool. There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. The TPMS sensor matching process is: 1. Set the parking brake. 2. Turn the ignition to ON/RUN with


the engine off.


3. Press the Remote Keyless Entry


(RKE) transmitter's LOCK and UNLOCK buttons at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.


Vehicle Care


10-65


If the vehicle does not have RKE, press the Driver Information Center (DIC) vehicle information button until the PRESS V TO RELEARN TIRE POSITIONS message displays. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen. If the vehicle does not have RKE or DIC buttons, press the trip odometer reset stem located on the instrument panel cluster until the PRESS V TO RELEARN TIRE POSITIONS message displays. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.


4. Start with the driver side


front tire.


Chevrolet Express Owner Manual - 2011


Black plate (66,1)


10-66


Vehicle Care


5. Place the relearn tool against


9. Turn the ignition switch to


the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.


6. Proceed to the passenger side


front tire, and repeat the procedure in Step 5.


7. Proceed to the passenger side


rear tire, and repeat the procedure in Step 5.


8. Proceed to the driver side rear


tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.


LOCK/OFF.


10. Set all four tires to the


recommended air pressure level as indicated on the Tire and Loading Information label.


Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month. Replace the tire if: . The indicators at three or


more places around the tire can be seen.


. There is cord or fabric


showing through the tire's rubber.


. The tread or sidewall is


cracked, cut, or snagged deep enough to show cord or fabric.


. The tire has a bump, bulge,


or split.


. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.


Tire Rotation Tires should be rotated every 12 000 km (7,500 mi). See Scheduled Maintenance on page 11‑3. Tires are rotated to achieve a uniform wear for all tires. The first rotation is the most important. Any time unusual wear is noticed, rotate the tires as soon as possible and check the wheel alignment. Also check for damaged tires or wheels.


Chevrolet Express Owner Manual - 2011


Black plate (67,1)


See When It Is Time for New Tires on page 10‑68 and Wheel Replacement on page 10‑74.


Use this rotation pattern when rotating the tires. If the vehicle has a compact spare tire, do not include it in the tire rotation.


Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated. See Tire Pressure on page 10‑60 and Vehicle Load Limits on page 9‑12. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10‑63. Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 12‑2.


Vehicle Care


10-67


{ WARNING


Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.


Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.


Chevrolet Express Owner Manual - 2011


Black plate (68,1)


10-68


Vehicle Care


Dual Tire Rotation When the vehicle is new, or whenever a wheel, wheel bolt, or wheel nut is replaced, check the wheel nut torque after 160, 1 600, and 10 000 km (100, 1,000, and 6,000 m) of driving. For proper wheel nut tightening information, see “Removing the Flat Tire and Installing the Spare Tire” later in this section, under If a Tire Goes Flat on page 10‑76. Also see “Wheel Nut Torque” under Capacities and Specifications on page 12‑2.


The outer tire on a dual wheel setup generally wears faster than the inner tire. Tires last longer and wear more evenly if they are rotated. See Tire Inspection on page 10‑66 and Tire Rotation on page 10‑66. Also see Scheduled Maintenance on page 11‑3. { WARNING


If the vehicle is operated with a tire that is underinflated, the tire can overheat. An overheated tire can lose air suddenly or catch fire. You or others could be injured. Properly inflate all tires, including the spare.


See Tires on page 10‑52 and Tire Pressure on page 10‑60 for more information on proper tire inflation.


When It Is Time for New Tires Factors such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.


Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining.


Chevrolet Express Owner Manual - 2011


Black plate (69,1)


Some commercial truck tires, including Goodyear LT225/75R16
G949 RSA and Goodyear LT225/ 75R16 G933 RSD, may not have treadwear indicators. If the tires do not have treadwear indicators, replace the tires when the tread depth is down to 3.2 mm (1/8 in) for the front tires, or 1.6 mm (1/16 in) for the rear tires. See Tire Inspection on page 10‑66 and Tire Rotation on page 10‑66 for additional information. The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple conditions including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place.


Tires will typically need to be replaced due to wear before they may need to be replaced due to age. Consult the tire manufacturer for more information on when tires should be replaced. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. This area should be free of grease, gasoline or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.


Vehicle Care


10-69


Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating. GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all‐season tread design, the TPC Spec number will be followed by MS for mud and snow. See Tire Sidewall Labeling on page 10‑53 for additional information.


Chevrolet Express Owner Manual - 2011


Black plate (70,1)


10-70


Vehicle Care


GM recommends replacing all the tires at the same time. Uniform tread depth on all tires will help to maintain the performance of the vehicle. Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. See Tire Inspection on page 10‑66 and Tire Rotation on page 10‑66 for information on proper tire rotation.


{ WARNING Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death. Only your dealer or authorized tire service center should mount or dismount the tires.


{ WARNING


Mixing tires of different sizes, brands, or types may cause loss of control of the vehicle, resulting in a crash or other vehicle damage. Use the correct size, brand, and type of tires on all wheels. This vehicle may have a different size spare than the road tires originally installed on the vehicle. When new, the vehicle included a spare tire and wheel assembly with a similar overall diameter as the road tires and wheels, so it is all right to drive on it.


(Continued)


WARNING (Continued)


The spare tire was developed for use on this vehicle and will not affect vehicle handling.


{ WARNING


Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving. A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.


Chevrolet Express Owner Manual - 2011


Black plate (71,1)


Vehicle Care


10-71


WARNING (Continued)


This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems developed for the vehicle, and have them properly installed by a GM certified technician.


See Buying New Tires on page 10‑69 and Accessories and Modifications on page 10‑3 for additional information.


If the vehicle tires must be replaced with a tire that does not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction (radial) as the original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low‐pressure warning if non‐TPC Spec rated tires are installed. See Tire Pressure Monitor System on page 10‑62. The Tire and Loading Information label indicates the original equipment tires on the vehicle. See Vehicle Load Limits on page 9‑12 for the label location and more information about the Tire and Loading Information label.


Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, and electronic stability control, the performance of these systems can also be affected.


{ WARNING


If different sized wheels are used, there may not be an acceptable level of performance and safety if tires not recommended for those wheels are selected.


(Continued)


Chevrolet Express Owner Manual - 2011


Black plate (72,1)


10-72


Vehicle Care


Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:


Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires.


The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.


Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.


Chevrolet Express Owner Manual - 2011


Black plate (73,1)


Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.


Vehicle Care


10-73


properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, check the alignment if there is unusual tire wear or if the vehicle is pulling to one side or the other. If the vehicle vibrates when driving on a smooth road, the tires and wheels might need to be rebalanced. See your dealer for proper diagnosis.


Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is


Chevrolet Express Owner Manual - 2011


Black plate (74,1)


10-74


Vehicle Care


Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces.


Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.


{ WARNING


Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.


Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See If a Tire Goes Flat on page 10‑76 for more information. Used Replacement Wheels


{ WARNING


Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.


Chevrolet Express Owner Manual - 2011


Black plate (75,1)


Tire Chains


{ WARNING


Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash. To help avoid damage to the vehicle, drive slowly, readjust, or remove the device if it is contacting the vehicle. Do not spin the vehicle's tires. Follow the manufacturer's instructions.


Notice: Use tire chains only where legal and only when you must. Use chains that are the proper size for the tires. Install them on the tires of the rear axle. Do not use chains on the tires of the front axle. Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer's instructions. If you can hear the chains contacting the vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage the vehicle.


Vehicle Care


10-75


For Cutaway models with LT245/75R16, LT225/75R16 or LT215/85R16 size single or dual rear tires, use Low Profile Z-Chain or SAE Class S cables. For Cargo or Passenger models with P245/70R17, LT225/75R16 or LT245/75R16 size tires, use Low Profile Z-Chain cables. SAE Class S chains are not recommended. If the vehicle has dual rear tires, do not use individual tire chains. Use tire chains that fit across both dual tires.


Chevrolet Express Owner Manual - 2011


Black plate (76,1)


10-76


Vehicle Care


If a Tire Goes Flat It is unusual for a tire to blow out while driving, especially if the tires are maintained properly. If air goes out of a tire, it is much more likely to leak out slowly. But if there ever is a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.


{ WARNING


Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.


{ WARNING Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for (Continued)


WARNING (Continued)


changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.


If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑5.


{ WARNING


Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall causing injury or death. Find a level place to change the tire.


(Continued)


Chevrolet Express Owner Manual - 2011


Black plate (77,1)


WARNING (Continued)


To help prevent the vehicle from moving:


1. Set the parking brake firmly. 2. Put an automatic


transmission in P (Park) or a manual transmission in 1 (First) or R (Reverse).


3. Turn off the engine and do not restart while the vehicle is raised.


4. Do not allow passengers to


remain in the vehicle.


5. Place wheel blocks on both


sides of the tire at the opposite corner of the tire being changed.


When the vehicle has a flat tire (B), use the following example as a guide to assist in the placement of the wheel blocks (A).


Vehicle Care


10-77


Tire Changing


Removing the Spare Tire and Tools If you have a cargo van or a passenger van, the equipment you will need is located in the passenger side rear corner of the vehicle.


A. Wheel Block B. Flat Tire The following information explains how to repair or change a tire.


Remove the retaining wing bolt and lift it off of the mounting bracket.


Chevrolet Express Owner Manual - 2011


Black plate (78,1)


10-78


Vehicle Care


If you have a van with the 15‐passenger seating arrangement, the equipment you will need is secured on the rear floor of the passenger side of the vehicle.


To access the equipment, remove the retaining wing bolt and lift it out of the mounting bracket.


To lower the spare tire from the vehicle:


The tools you will be using include: A. Jack B. Jack Handle C. Hoist Extension D. Jack Handle Extension E. Wheel Wrench The spare tire is mounted in the rear underbody of the vehicle. You will use the hoist extension, the jack handle extensions and the wheel wrench to remove the underbody‐mounted spare tire.


A. Spare Tire B. Tire/Wheel Retainer C. Hoist Cable D. Hoist Assembly E. Hoist Shaft F.


Jack Handle and Hoist Extensions


G. Wheel Wrench


Chevrolet Express Owner Manual - 2011


Black plate (79,1)


Vehicle Care


10-79


3. Turn the wheel wrench


counterclockwise to lower the spare tire to the ground. Continue to turn the wheel wrench until the spare tire can be pulled out from under the vehicle. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower. See Secondary Latch System on page 10‑86.


1. Assemble the wheel wrench (G) to one or two of the jack handle and the hoist extensions (F). Insert the hoist extension end through the hole in the rear bumper.


2. Be sure the hoist extension end


connects to the hoist shaft (E). The chiseled end of the extension is used to lower the spare tire.


4. When the tire has been


lowered, pull the tire toward you so you can reach the tire retainer and pull it up through the wheel opening. If you have a vehicle which was completed from a cab and chassis, refer to the information from body supplier/installer. The spare tire is a full‐size tire, like the other tires on the vehicle.


5. Put the spare tire near the


flat tire.


Chevrolet Express Owner Manual - 2011


Black plate (80,1)


10-80


Vehicle Care


Removing the Flat Tire and Installing the Spare Tire If the vehicle has plastic wheel nut caps, loosen them by turning the wheel wrench counterclockwise. The wheel nut caps are designed to remain with the center cap. Remove the center cap. If the wheel has a smooth center piece, place the chisel end of the wheel wrench in the slot on the wheel and gently pry it out. 1. Do a safety check before


proceeding. See If a Tire Goes Flat on page 10‑76 for more information.


2. Loosen all the wheel nuts with


the wheel wrench. Do not remove them yet.


3. Assemble the jack and tools:


Front Flat: Assemble the jack (A) together with the jack handle (B), one or two jack handle extensions (D) and the wheel wrench (E). Rear Flat: Assemble the jack (A) together with the jack handle (B), two jack handle extensions (D), and the wheel wrench (E).


Front Position


Front Position


Chevrolet Express Owner Manual - 2011


Black plate (81,1)


Vehicle Care


10-81


{ WARNING Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.


5. Raise the vehicle by turning the wheel wrench clockwise. Raise the vehicle far enough off the ground so there is enough room for the spare tire to fit.


4. Position the jack under the


vehicle as shown. The front position jacking point is on the frame. The rear position jacking point is on the rear axle. If the exhaust system interferes in the jack location in the rear axle, such as in Diesel vehicles, place the jack (A) on the rear axle between the axle housing and the shock absorber bracket in order to avoid any interference with the exhaust pipe (B).


{ WARNING


Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.


Rear Position


Rear Alternative Position (Diesel


Vehicles)


Chevrolet Express Owner Manual - 2011


Loading...
x