2012 Chevrolet Equinox Owners Manual

OFF: Use to turn the wipers off. 8 (Mist): For a single wipe, briefly move the wiper lever down. For several wipes, hold the wiper lever down.

The windshield wiper/washer lever is located on the right side of the steering column. With the ignition in ACC/ACCESSORY or ON/RUN/ START, move the windshield wiper lever to select the wiper speed. HI: Use for fast wipes. LO: Use for slow wipes.

Chevrolet Equinox Owner Manual - 2012

Black plate (4,1)

5-4

Instruments and Controls

n L FRONT (Windshield Washer): Pull the windshield wiper lever toward you to spray windshield washer fluid and activate the wipers. The wipers will continue until the lever is released or the maximum wash time is reached. When the windshield wiper lever is released, additional wipes may occur depending on how long the windshield washer had been activated. See Washer Fluid on page 10‑23 for information on filling the windshield washer fluid reservoir.

{ WARNING

In freezing weather, do not use the washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.

Clear snow and ice from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged blades should be replaced. See Wiper Blade Replacement on page 10‑29. Heavy snow or ice can overload the wiper motor.

Wipe Parking If the ignition is turned to LOCK/ OFF while the wipers are on LO, HI, or INT, they will immediately stop. If the windshield wiper lever is then moved to off before the driver door is opened or within 10 minutes, the wipers will restart and move to the base of the windshield. If the ignition is turned to LOCK/ OFF while the wipers are performing wipes due to windshield washing, the wipers continue to run until they reach the base of the windshield.

Chevrolet Equinox Owner Manual - 2012

Black plate (5,1)

Rear Window Wiper/ Washer The rear wiper controls are on the end of the windshield wiper lever.

ON: Press the upper portion of the button for continuous rear window wipes. OFF: The rear wiper turns off when the button is returned to the middle position. INT (Intermittent Rear Wipes): Press the lower portion of the button to set a delay between wipes. m = REAR (Rear Washer): Push the windshield wiper lever forward to spray washer fluid on the rear window. The lever returns to its starting position when released.

Instruments and Controls

5-5

Reverse Gear Wipes If the rear wiper control is off, the rear wiper will automatically operate continuously when the shift lever is in R (Reverse), and the front windshield wiper is performing low or high speed wipes. If the rear wiper control is off, the shift lever is in R (Reverse), and the front windshield wiper is performing interval wipes, then the rear wiper automatically performs interval wipes. The windshield washer reservoir is used for the windshield and the rear window. Check the fluid level in the reservoir if either washer is not working. See Washer Fluid on page 10‑23.

Compass The vehicle may have a compass display on the Driver Information Center (DIC). The compass receives its heading and other information

from the Global Positioning System (GPS) antenna, StabiliTrak, and vehicle speed information. Avoid covering the GPS antenna for long periods of time with objects that may interfere with the antenna's ability to receive a satellite signal. See Multi-Band Antenna on page 7‑23 for the location of the vehicle's antenna. The compass system is designed to operate for a certain number of miles or degrees of turn before needing a signal from the GPS satellites. When the compass display shows CAL, drive the vehicle for a short distance in an open area where it can receive a GPS signal. The compass system will automatically determine when a GPS signal is restored and provide a heading again. See Compass Messages on page 5‑28 for more information on the messages that may be displayed for the compass.

Chevrolet Equinox Owner Manual - 2012

Black plate (6,1)

5-6

Instruments and Controls

Clock The infotainment system controls, located on the instrument panel, are used to access the time and date settings through the menu system. See Operation on page 7‑10 for information about how to use the menu system. For vehicles with a navigation system, see the separate navigation manual to set the clock. Setting the Clock with Date Display To set the Time and Date: 1. Turn the infotainment system on. 2. Press the CONFIG button and select Time and Date Settings.

3. Select Set Time or Set Date. 4. Turn the MENU/SEL knob to adjust the highlighted value.

5. Press the MENU/SEL knob to

select the next value.

6. To save the time or date and return to the Time and Date Settings menu, press the E BACK button at any time or press the MENU/SEL knob after adjusting the minutes or year.

To set the 12/24 hour format: 1. Turn the infotainment system on. 2. Press the CONFIG button and select Time and Date Settings.

3. Highlight 12/24 Hour Format. 4. Press the MENU/SEL knob to select the 12 hour or 24 hour display format.

To set the month and day format: 1. Turn the infotainment system on. 2. Press the CONFIG button and select Time and Date Settings.

3. Highlight Month and Day

Format.

4. Press the MENU/SEL knob to select MM/DD (month/day) or DD/MM (day/month).

To set the auto time adjust: 1. Turn the infotainment system on. 2. Press the CONFIG button and select Time and Date Settings.

3. Highlight Auto Time Adjust. 4. Press the MENU/SEL knob to

turn Auto Time Adjust on or off.

5. Press the MENU/SEL knob to

select Time Zone, and then select the time zone.

6. Press the MENU/SEL knob to turn Daylight Savings on or off.

Setting the Clock Without Date Display To set the Time and Date: 1. Turn the infotainment system on. 2. Press the CONFIG button and select Time Settings, or press the H button.

Chevrolet Equinox Owner Manual - 2012

Black plate (7,1)

3. Select Set Time. 4. Turn the MENU/SEL knob to adjust the highlighted value.

5. Press the MENU/SEL knob to

select the next value.

6. To save the time and return to the Time Settings menu, press the E BACK button at any time or press the MENU/SEL knob after adjusting the minutes.

To set the 12/24 hour format: 1. Turn the infotainment system on. 2. Press the CONFIG button and select Time Settings, or press the H button.

3. Highlight 12/24 Hour Format. 4. Press the MENU/SEL knob to select the 12 hour or 24 hour display format.

Instruments and Controls

5-7

Setting the Clock (Radio with CD and Touchscreen) To set the time: 1. Press the CONFIG button to

enter the menu options. Turn the TUNE/MENU knob to scroll through the available setup features. Press the TUNE/MENU knob or press the Time screen button to display other options within that feature.

2. Press + or − to decrease or

increase the Hours and Minutes displayed on the clock.

12/24 HR Format: Press the 12 HR screen button for standard time; press the 24 HR screen button for military time. Day + or Day −: Press the Day + or Day − display buttons to increase or decrease the day. Display: Press Display to turn the display of the time on the screen on or off.

Power Outlets The accessory power outlets can be used to connect electrical equipment, such as a cell phone or MP3 player. There are four accessory power outlets in the following locations: below the CD slot, inside the center console storage, on the rear of the center console storage, and in the rear cargo compartment. To use the outlets, remove the cover and close when not in use. Notice: Leaving electrical equipment plugged in for an extended period of time while the vehicle is off will drain the battery. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 ampere rating.

Chevrolet Equinox Owner Manual - 2012

Black plate (8,1)

5-8

Instruments and Controls

Certain accessory plugs may not be compatible with the accessory power outlets and could overload vehicle and adapter fuses. If a problem is experienced, see your dealer. When adding electrical equipment, be sure to follow the installation instructions included with the equipment. See Add-On Electrical Equipment on page 9‑63. Notice: Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords.

Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Warning lights come on when there could be a problem with a vehicle function. Some warning lights come on briefly when the engine is started to indicate they are working.

Gauges can indicate when there could be a problem with a vehicle function. Often gauges and warning lights work together to indicate a problem with the vehicle. When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Follow this manual's advice. Waiting to do repairs can be costly and even dangerous.

Chevrolet Equinox Owner Manual - 2012

Black plate (9,1)

Instrument Cluster

Instruments and Controls

5-9

English Shown, Metric Similar

Chevrolet Equinox Owner Manual - 2012

Black plate (10,1)

5-10

Instruments and Controls

Speedometer The vehicle's speed can be selected to display on the Driver Information Center (DIC) and the speedometer in either kilometers per hour (km/h) or miles per hour (mph). Telltales on the speedometer indicate whether kilometers or miles were chosen. The DIC will show the vehicle's speed after the limit on the speedometer has been reached.

Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper‐resistant odometer. The digital odometer will read 999,999 if it is turned back. If the vehicle needs a new odometer installed, it must be set to the mileage total of the old odometer.

Tachometer The tachometer displays the engine speed in revolutions per minute (rpm).

Fuel Gauge

Metric

Chevrolet Equinox Owner Manual - 2012

Black plate (11,1)

Instruments and Controls

5-11

Engine Coolant Temperature Gauge

Metric

Here are some situations that can occur with the fuel gauge. None of these indicate a problem with the fuel gauge. . At the service station, the fuel

pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge may have indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. The gauge moves a little while turning a corner or speeding up. The gauge takes a few seconds to stabilize after the ignition is turned on, and goes back to empty when the ignition is turned off.

English

When the ignition is on, the fuel gauge shows about how much fuel the vehicle has left in the fuel tank. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. The gauge will first indicate empty before the vehicle is out of fuel and the low fuel light comes on, but the vehicle's fuel tank should be filled soon.

Chevrolet Equinox Owner Manual - 2012

Black plate (12,1)

5-12

Instruments and Controls

Safety Belt Reminders

Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument panel cluster.

Passenger Safety Belt Reminder Light

English

This gauge measures the temperature of the vehicle's engine. If the indicator needle moves to the hot side of the gauge toward the colored line, the engine is too hot. If the vehicle has been operated under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible.

When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on.

When the vehicle is started, this light flashes and a chime may come on to remind front passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the front passenger remains or becomes unbuckled while the vehicle is moving. If the front passenger safety belt is buckled, neither the chime nor the light comes on.

Chevrolet Equinox Owner Manual - 2012

Black plate (13,1)

Instruments and Controls

5-13

The front passenger safety belt reminder light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop, or other electronic device. To turn off the reminder light and/or chime, remove the object from the seat or buckle the safety belt.

Airbag Readiness Light This light shows if there is an electrical problem. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 3‑21.

The airbag readiness light comes on and stays on for several seconds when the vehicle is started. Then the light goes out.

{ WARNING

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3‑28 for important safety information. The overhead console has a passenger airbag status indicator.

United States

Canada

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds

Chevrolet Equinox Owner Manual - 2012

Black plate (14,1)

5-14

Instruments and Controls

as a system check. If you are using remote start to start the vehicle from a distance, if equipped, you may not see the system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ WARNING

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑13 for more information, including important safety information.

Charging System Light

The light turns off when the engine is started. If it does not, have the vehicle serviced by your dealer. If the light stays on, or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. When this light comes on, the Driver Information Center (DIC) also displays a message. See Battery Voltage and Charging Messages on page 5‑27. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working.

Chevrolet Equinox Owner Manual - 2012

Black plate (15,1)

Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions are at acceptable levels, to produce a cleaner environment. This light comes on when the vehicle is placed in ON/RUN, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. See Ignition Positions on page 9‑21 for more information.

If the malfunction indicator lamp comes on and stays on while the engine is running, this indicates that there is an OBD II problem and service is required.

Instruments and Controls

5-15

Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the

vehicle warranty. This could also result in a failure to pass a required Emission Inspection/ Maintenance test. See Accessories and Modifications on page 10‑3. This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades.

If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.

Chevrolet Equinox Owner Manual - 2012

Black plate (16,1)

5-16

Instruments and Controls

If the light continues to flash, stop and park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emission system malfunction: . Check that the fuel cap is fully

installed. See Filling the Tank on page 9‑54. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off.

. Check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9‑51. If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed.

Emissions Inspection and Maintenance Programs Some local governments may have programs to inspect the on-vehicle emission control equipment. For the inspection, the emission system test equipment is connected to the vehicle’s Data Link Connector (DLC).

The DLC is under the instrument panel to the left of the steering wheel. See your dealer if assistance is needed.

Chevrolet Equinox Owner Manual - 2012

Black plate (17,1)

Instruments and Controls

5-17

The vehicle may not pass inspection if:

The malfunction indicator lamp is on with the engine running, or if the light does not come on when the ignition is turned to ON/RUN while the engine is off. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed. The vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working

Metric

English

The brake indicator light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer. When the ignition is on, the brake system warning light comes on when the parking brake is set. The light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully

released, there is a brake problem. Have the brake system inspected immediately.

{ WARNING

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

If the light comes on while driving, a chime sounds. Pull off the road and stop. The pedal might be harder to push or go closer to the floor. It might also take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle on page 10‑77.

Chevrolet Equinox Owner Manual - 2012

Black plate (18,1)

5-18

Instruments and Controls

Antilock Brake System (ABS) Warning Light

For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem.

If the ABS light comes on and stays on while driving, stop as soon as possible and turn the ignition off. Start the engine again to reset the system. If the light stays on after driving at a speed above 20 km/h (13 mph), see your dealer for service. A chime may also sound when the light comes on steady. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5‑17. See Brake System Messages on page 5‑28 for all brake‐related DIC messages.

Lane Departure Warning (LDW) Light

For vehicles with the lane departure warning system, this light is located on the center of the instrument panel. This light briefly comes on green while starting the vehicle. If it does not, have the vehicle serviced by your dealer. If the system is working normally the indicator light then turns off.

Chevrolet Equinox Owner Manual - 2012

Black plate (19,1)

This light also comes on green when the system is switched on and ready to operate. See Lane Departure Warning (LDW) on page 9‑48 for more information.

Forward Collision Alert (FCA) Warning Light These lights are located on the center of the instrument panel.

The vehicle ahead light comes on when a vehicle is ahead and a possible collision can occur.

Instruments and Controls

5-19

Traction Off Light

The forward collision alert comes on and warns when following a vehicle closely. The light then flashes when a vehicle is being rapidly approached. See Forward Collision Alert (FCA) System on page 9‑41 for more information.

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly.

Chevrolet Equinox Owner Manual - 2012

Black plate (20,1)

5-20

Instruments and Controls

See Traction Control System (TCS) on page 9‑35 and StabiliTrak® System on page 9‑37 for more information.

See Traction Control System (TCS) on page 9‑35 and StabiliTrak® System on page 9‑37 for more information.

StabiliTrak® OFF Light

Traction Control System (TCS)/StabiliTrak® Light

This light comes on when the StabiliTrak system is turned off. If the Traction Control System (TCS) is off, wheel spin is not limited. If the StabiliTrak system is off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak system and the warning light turns off. Check the DIC for applicable messages. See Ride Control System Messages on page 5‑31 for more information.

The StabiliTrak system or the Traction Control System (TCS) indicator/warning light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by the dealer. If the system is working normally, the indicator light turns off.

If the light is on and not flashing, the TCS, and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the indicator/warning light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See StabiliTrak® System on page 9‑37 and Traction Control System (TCS) on page 9‑35 for more information.

Chevrolet Equinox Owner Manual - 2012

Black plate (21,1)

Instruments and Controls

5-21

When the Light Flashes First and Then Is On Steady This indicates that there may be a problem with the TPMS. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor Operation on page 10‑53 for more information.

Engine Oil Pressure Light

{ WARNING

Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.

Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule for changing engine oil.

The oil pressure light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Tire Pressure Light

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A tire pressure message can accompany the light. See Tire Messages on page 5‑33 for more information. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑50 for more information.

Chevrolet Equinox Owner Manual - 2012

Black plate (22,1)

5-22

Instruments and Controls

Fuel Economy Light

Low Fuel Warning Light

For vehicles with a Driver Information Center (DIC), see Fuel System Messages on page 5‑30 for more information.

Security Light

For vehicles with the fuel economy mode light, it comes on when the eco (economy) switch, located on the center console near the shifter, is pressed. For vehicles with a Driver Information Center (DIC) an ECO MODE ON message displays. See Fuel System Messages on page 5‑30 for more information. Press the switch again to turn off the light and exit the fuel saver mode.

English Shown, Metric Similar

This light comes on for a few seconds when the ignition is turned on as a check to indicate it is working. If it does not come on, have it fixed. The low fuel warning light is a circle located on the fuel gauge. This light comes on and a chime sounds periodically when the vehicle is low on fuel. The light goes off when fuel is added to the fuel tank.

The immobilizer light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation on page 2‑14 for more information.

Chevrolet Equinox Owner Manual - 2012

Black plate (23,1)

High-Beam On Light

Front Fog Lamp Light

Cruise Control Light

Instruments and Controls

5-23

The high‐beam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑2 for more information.

The front fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 6‑4 for more information.

Lamps On Reminder

The cruise control light is white whenever the cruise control is set, and turns green when the cruise control is active. The light turns off when the cruise control is turned off. See Cruise Control on page 9‑38 for more information.

For vehicles with the lamps on reminder light, it comes on when the lights are in use.

Chevrolet Equinox Owner Manual - 2012

Black plate (24,1)

5-24

Instruments and Controls

Information Displays

Driver Information Center (DIC) The vehicle may have a Driver Information Center (DIC). It displays information about the vehicle and warning messages if there is a system problem detected. DIC messages display in the center of the instrument panel cluster. See Vehicle Messages on page 5‑27 for more information. The vehicle may also have features that can be customized through the controls on the radio. See Vehicle Personalization on page 5‑34 for more information. DIC Operation and Displays Use the DIC buttons located in the center of the instrument panel to access different displays. The DIC displays trip, fuel, vehicle system information, and warning messages.

It also shows the shift lever position, the odometer, and the direction the vehicle is driving.

DIC Buttons

MENU: Press this button to get to the Trip/Fuel Menu and the Vehicle Information Menu. Q or R : Use these buttons to scroll through the items in each menu. A small marker will move along the page as you scroll through the items. This shows where each page is in the menu.

SET/CLR (Set/Clear): Use this button to set or clear the menu item when it is displayed. Trip/Fuel Menu Items Press the MENU button until Trip/ Fuel Information Menu is displayed. Then press R to scroll through the following menu items:

Trip 1
Trip 2
Fuel Range

. Average Fuel Economy

Instantaneous Fuel Economy

. Average Vehicle Speed

Timer

. Digital Speedometer

Turn-by-Turn . Blank Display

Chevrolet Equinox Owner Manual - 2012

Black plate (25,1)

Instruments and Controls

5-25

Trip 1 and Trip 2
This display shows the current distance traveled, in either kilometers (km) or miles (mi), since the last reset for the trip odometer. The trip odometer can be reset to zero by pressing SET/CLR while the trip odometer display is showing.

Fuel Range This display shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Fuel range cannot be reset.

Average Fuel Economy This display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. The fuel economy can be reset by

pressing SET/CLR while the Average Fuel Economy display is showing. The display may not reset to zero.

Instantaneous Fuel Economy This display shows the current fuel economy in either liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the fuel economy that the vehicle has right now and changes frequently as driving conditions change. Unlike average economy, this display cannot be reset.

Average Vehicle Speed This display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing SET/CLR while the Average Vehicle Speed display is showing.

Timer This display can be used as a timer. To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR.

Digital Speedometer The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.

Chevrolet Equinox Owner Manual - 2012

Black plate (26,1)

5-26

Instruments and Controls

Turn-by-Turn This display is used for the OnStar or Navigation System Turn-by-Turn guidance. See OnStar Overview on page 14‑1 or the Navigation manual, if the vehicle has navigation, for more information.

Blank Display This display shows no information. Vehicle Information Menu Items Press the MENU button until Vehicle Information Menu is displayed. Then press R to scroll through the following menu items: . Unit

Tire Pressure

. Remaining Oil Life . Blank Display

Unit Press SET/CLR to enter the unit menu. Then press Q or R to switch between METRIC or US when the Unit display is active. Press SET/ CLR to confirm the setting. This will change the displays on the cluster and DIC to either metric or English (US) measurements.

Tire Pressure The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). See Tire Pressure Monitor System on page 10‑51 and Tire Pressure Monitor Operation on page 10‑53 for more information.

Remaining Oil Life This display shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5‑29. The oil should be changed as soon as possible. See Engine Oil on page 10‑10. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Maintenance Schedule on page 11‑3 for more information. Remember, the Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Oil Life display accidentally at any time other than when the oil has just been changed.

Chevrolet Equinox Owner Manual - 2012

Black plate (27,1)

It cannot be reset accurately until the next oil change. To reset the engine oil life system, press SET/ CLR while the Oil Life display is active. The display will ask for confirmation of a reset. Press Q or R to select Yes or No. Then press SET/CLR to confirm the selection. See Engine Oil Life System on page 10‑12.

Blank Display This display shows no information. Compass The vehicle may have a compass in the Driver Information Center (DIC). See Compass on page 5‑5.

Instruments and Controls

5-27

Battery Voltage and Charging Messages

BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that features are disabled, this message is displayed. It means that the vehicle is trying to save the charge in the battery. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10‑26 for more information.

Vehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action, but you can press SET/CLR to acknowledge that you received the messages and to clear them from the display. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear, not correct the problem. You will find the possible messages that can be displayed and some information about them grouped by subject in the following information.

Chevrolet Equinox Owner Manual - 2012

Black plate (28,1)

5-28

Instruments and Controls

SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.

Brake System Messages

BRAKE FLUID LOW This message is displayed when the brake fluid level is low; see Brake Fluid on page 10‑24. RELEASE PARKING BRAKE This message is displayed as a reminder that the parking brake is on. Release it before you attempt to drive.

Compass Messages

Door Ajar Messages

CAL This message is displayed when the compass needs to be calibrated. See Compass on page 5‑5. – – – Three dashes will be displayed if the compass needs service. See your dealer for service.

Cruise Control Messages

APPLY BRAKE BEFORE CRUISE If this message displays when attempting to activate cruise control, apply the brake pedal and try again. CRUISE SET TO XXX This message displays when the cruise control is set and shows the speed it was set to. See Cruise Control on page 9‑38 for more information.

DOOR OPEN A door open symbol will be displayed on the DIC showing which door is open. If the vehicle has been shifted out of P (Park), a DOOR OPEN message will also be displayed. Close the door completely. MANUALLY CLOSE THE POWER LIFTGATE This message will display if the power liftgate encounters multiple obstacles on the same power cycle. After removing the obstructions, the liftgate will resume normal power operation. REAR ACCESS OPEN This message will display along with a symbol when the liftgate is open. Close the liftgate completely.

Chevrolet Equinox Owner Manual - 2012

Black plate (29,1)

Instruments and Controls

5-29

Engine Cooling System Messages

A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. COOLANT LEVEL LOW ADD COOLANT This message will display if the coolant is low. See Engine Coolant on page 10‑17.

ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature. HIGH COOLANT TEMPERATURE This message displays if the coolant temperature is hot. See Engine Overheating on page 10‑20.

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the Oil Life System. See Engine Oil Life System on page 10‑12 and Driver Information Center (DIC) on page 5‑24 for information on how to reset the system. See Engine Oil on page 10‑10 and Maintenance Schedule on page 11‑3 for more information. ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down.

Chevrolet Equinox Owner Manual - 2012

Black plate (30,1)

5-30

Instruments and Controls

ENGINE OIL LOW — ADD OIL This message displays when the engine oil level is too low. Check the oil level. See Engine Oil on page 10‑10. OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.

Engine Power Messages

ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the

next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

ECO MODE ON On some models, this message displays when the fuel economy mode has been turned on by pressing the eco button near the shift lever. See Fuel Economy Mode on page 9‑32 for more information. FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible. TIGHTEN GAS CAP This message displays when the fuel cap is not on tight. Tighten the fuel cap.

Key and Lock Messages

REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced.

Object Detection System Messages

FORWARD COLLISION ALERT OFF If your vehicle has the Forward Collision Alert (FCA) system, this message may display if the FCA system cannot activate due to a temporary condition. See Forward Collision Alert (FCA) System on page 9‑41.

Chevrolet Equinox Owner Manual - 2012

Black plate (31,1)

Instruments and Controls

5-31

FRONT CAMERA BLOCKED, CLEAN WINDSHIELD This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled because the camera view is blocked and cannot operate properly. It may also activate during heavy rain or due to road spray. To clean the system, clean the outside of the windshield area in front of the LDW/FCA camera sensor. LANE DEPARTURE SYSTEM UNAVAILABLE If your vehicle has the Lane Departure Warning (LDW) system, this message may display if the LDW system cannot activate due to a temporary condition. See Lane Departure Warning (LDW) on page 9‑48 for more information.

PARK ASSIST OFF This message displays when the park assist system has been turned off or when there is a temporary condition causing the system to be disabled. See Ultrasonic Parking Assist on page 9‑43. SERVICE FRONT CAMERA This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled and need service. See your dealer/retailer. SERVICE PARK ASSIST This message displays if there is a problem with the Ultrasonic Rear Parking Assist (URPA) system. Do not use this system to help you park. See Ultrasonic Parking Assist on page 9‑43 for more information. See your dealer for service.

Ride Control System Messages

ALL WHEEL DRIVE OFF If your vehicle has the All-Wheel Drive (AWD) system, this message displays when the rear drive system is overheating. This message turns off when the rear drive system cools down. If the warning message stays on for a while, you need to reset the warning message. To reset the warning message, turn the ignition off and then back on again. If the message stays on, see your dealer right away. See All-Wheel Drive on page 9‑33 for more information.

Chevrolet Equinox Owner Manual - 2012

Black plate (32,1)

5-32

Instruments and Controls

SERVICE ALL WHEEL DRIVE If your vehicle has the All-Wheel Drive (AWD) system, this message displays if a problem occurs with this system. If this message appears, stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display. If the message is still displayed or appears again when you begin driving, the AWD system needs service. See your dealer. SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). See Traction Control System (TCS) on page 9‑35.

SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. StabiliTrak® System on page 9‑37. STABILITRAK OFF This message displays when the StabiliTrak system is turned off. See StabiliTrak® System on page 9‑37
for more information. TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly. TRACTION CONTROL ON This message displays when the Traction Control System (TCS) is first turned on. See Traction Control System (TCS) on page 9‑35 for more information.

Airbag System Messages

SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.

Safety Belt Messages

BUCKLE SEATBELT This message displays as a reminder when the safety belt is not buckled.

Anti-theft Alarm System Messages

THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.

Chevrolet Equinox Owner Manual - 2012

Black plate (33,1)

Instruments and Controls

5-33

Service Vehicle Messages

SERVICE AC SYSTEM This message is displayed if there is a problem with the air conditioning system. Take the vehicle to your dealer for service. SERVICE POWER STEERING This message is displayed if there is a problem with the power steering system. Take the vehicle to your dealer for service. SERVICE VEHICLE SOON This message is displayed if there is a problem with the vehicle. Take the vehicle to your dealer for service.

Tire Messages

SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑53 for more information.

TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10‑53 for more information. TIRE LOW ADD AIR TO TIRE This message displays when the pressure in one or more of the tires is low. This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate the location of the low tire. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑21. If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10‑42, Vehicle Load Limits on page 9‑16, and Tire Pressure on page 10‑50.

You can receive more than one tire pressure message at a time. The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5‑24.

Transmission Messages

SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when attempting to remove the key from the ignition or from the vehicle if the vehicle is not in P (Park). TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle.

Chevrolet Equinox Owner Manual - 2012

Black plate (34,1)

5-34

Instruments and Controls

Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Vehicle Reminder Messages

ICE POSSIBLE DRIVE WITH CARE This message is displayed when ice conditions are possible. TURN WIPER CONTROL TO INTERMITTENT FIRST This message is displayed when attempting to adjust the intermittent wiper speed without intermittent selected on the wiper control. See Windshield Wiper/Washer on page 5‑3.

Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features. CONFIG (Configuration): Press to access the Configuration Settings Menu. MENU/SELECT Knob: Press the center of this knob to enter the menus and select menu items. Turn the knob to scroll through the menus. E BACK: Press to exit or move backwards in a menu.

Entering the Personalization Menus 1. Turn the infotainment system on and press the CONFIG button to access the Configuration Settings menu.

2. Turn the MENU/SELECT knob to

highlight Vehicle Settings.

3. Press the center of the MENU/

SELECT knob to select the Vehicle Settings menu.

The following list of menu items will be available: . Climate and Air Quality . Comfort and Convenience . Collision/Detection Systems

Languages Lighting

. Power Door Locks . Remote Lock/Unlock/Start . Return to Factory Settings Turn the MENU/SELECT knob to highlight the menu. Press the knob to select it. Each of the menus is detailed in the following information. All of the menus may not be available. Only those tied to the features on your vehicle will be shown.

Chevrolet Equinox Owner Manual - 2012

Black plate (35,1)

Instruments and Controls

5-35

Climate and Air Quality Select the Climate and Air Quality menu and the following will be displayed: . Auto Fan Speed . Air Conditioning Mode . Remote Start Auto Heat Seats

Increased speed.

Auto Fan Speed This selection is available on vehicles with the Automatic Climate Control System. Choose from the following blower speed settings: High: Low: Reduced speed. Normal: Moderate speed. Press the MENU/SELECT knob when Auto Fan Speed is highlighted. Turn the knob to highlight “High,” “Normal,” or “Low.” Press the knob to confirm the selection and go back to the last menu.

Air Conditioning Mode This will allow you to select whether or not the air conditioning comes on automatically the next time the vehicle is started. “On” means that the air conditioning will be on at start up, regardless of whether it was on or off the last time the vehicle was turned off. “Off” means the air conditioning will be off at the next start up, regardless of whether it was on or off the last time the vehicle was turned off. “Last Setting” means that when the vehicle is started, the air conditioning will resume whichever setting it was at the last time the vehicle was turned off. Press the MENU/SELECT knob when Air Conditioning Mode is highlighted. Turn the knob to highlight “On,” “Off,” or “Last Setting.” Press the knob to confirm the selection and go back to the last menu.

Remote Start Auto Heat Seats When on, this feature will turn the heated seats on when using remote start on cold days. Press the MENU/SELECT knob when “Remote Start Auto Heat Seats” is highlighted to toggle between “On” or “Off.” Press E BACK to confirm the selection and go back to the last menu. Comfort and Convenience Select the Comfort and Convenience menu and the following will be displayed: . Easy Exit Driver Seat . Chime Volume . Reverse Tilt Mirror

Chevrolet Equinox Owner Manual - 2012

Black plate (36,1)

5-36

Instruments and Controls

Easy Exit Driver Seat When on, this feature will move the driver seat rearward upon turning the ignition off and the driver door opening. This may be performed to make it easier to exit the vehicle. See the “Easy Exit Driver Seat” information under Power Seat Adjustment on page 3‑4 for more information. This allows you to turn the easy exit seat feature on or off. Press the MENU/SELECT knob when “Easy Exit Driver Seat” is highlighted. Turn the knob to select “On” or “Off.” Press the knob to confirm and go back to the last menu.

Chime Volume This allows the selection of the chime volume level. Press the MENU/SELECT knob when “Chime Volume” is highlighted. Turn the knob to select

“Normal” or “High.” Press the knob to confirm and go back to the last menu.

Reverse Tilt Mirror When on, both the driver and passenger mirrors will tilt downward when vehicle is shifted to R (Reverse) to improve visibility of the ground near the rear wheels. They will return to their previous driving position when the vehicle is shifted out of R (Reverse), the ignition is turned to OFF, or the vehicle is left in reverse. See Park Tilt Mirrors on page 2‑17 for more information. This allows you to turn the park tilt mirrors feature on or off. Press the MENU/SELECT knob when “Reverse Tilt Mirror” is highlighted. Turn the knob to select “On” or “Off.” Press the knob to confirm and go back to the last menu.

Collision/Detection Systems Select the Collision/Detection Systems menu and the following will be displayed: . Park Assist

Park Assist This allows the Ultrasonic Parking Assist feature to be turned on or off. Press the MENU/SELECT knob when “Park Assist” is highlighted. Turn the knob to select “On,” “Off,” or “Tow Bar.” Press the knob to confirm and go back to the last menu. See Ultrasonic Parking Assist on page 9‑43 for more information Languages Select the Languages menu and the following will be displayed: . English French . Spanish

Chevrolet Equinox Owner Manual - 2012

Black plate (37,1)

Instruments and Controls

5-37

Turn the MENU/SELECT knob to select the language. Press the knob to confirm and go back to the last menu. Lighting Select the Lighting menu and the following will be displayed: . Vehicle Locator Lights . Exit Lighting

Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. Press the MENU/SELECT knob when “Vehicle Locator Lights” is highlighted to toggle between “On” or “Off.” Press E BACK to confirm the selection and go back to the last menu.

Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside.

Press the MENU/SELECT knob when “Exit Lighting” is highlighted. Turn the knob to select “Off,” “30 Seconds,” “1 Minute,” or “2 Minutes.” Press the knob to confirm and go back to the last menu. Power Door Locks Select Power Door Locks and the following will be displayed: . Unlocked Door Anti Lock Out . Auto Door Unlock . Delayed Door Lock

Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open. If off is selected, the Delayed Door Lock menu will be available. Press the MENU/SELECT knob when “Unlocked Door Anti Lock Out” is highlighted to toggle between “On” or “Off.” Press E BACK to confirm the selection and go back to the last menu.

Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park). Press the MENU/SELECT knob when “Auto Door Unlock” is highlighted. Turn the knob to select “All Doors,” “Driver Door,” or “Off.” Press the knob to confirm and go back to the last menu.

Delayed Door Lock When on, this feature will delay the locking of the doors. If you want to override the delay you can press the power door lock on the instrument panel. Press the MENU/SELECT knob when “Delayed Door Lock” is highlighted. Turn the knob to select “On” or “Off.” Press the knob to confirm and go back to the last menu.

Chevrolet Equinox Owner Manual - 2012

Black plate (38,1)

5-38

Instruments and Controls

Remote Lock/Unlock/Start Select Remote Lock/Unlock/Start and the following will be displayed: . Remote Unlock Light Feedback . Remote Lock Feedback . Remote Door Unlock . Memory Remote Recall

Remote Unlock Light Feedback When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Press the MENU/SELECT knob when “Remote Unlock Light Feedback” is highlighted. Turn the knob to select “Flash Lights” or “Off.” Press the knob to confirm and go back to the last menu.

Remote Lock Feedback This allows selection of what type of feedback is given when unlocking the vehicle with the RKE transmitter. Press the MENU/SELECT knob when “Remote Lock Feedback” is highlighted. Turn the knob to select

“Lights and Horn,” “Lights Only,” “Horn Only,” or “Off.” Press the knob to confirm and go back to the last menu.

Remote Door Unlock This allows selection of which doors will unlock when pressing the unlock button on the RKE transmitter. Press the MENU/SELECT knob when “Remote Door Unlock” is highlighted. Turn the knob to select “All Doors” or “Driver Door.” Press the knob to confirm and go back to the last menu.

Memory Remote Recall This allows the Memory Remote Recall feature to be turned on or off. When on, this feature will recall the current driver's last seat, outside mirrors upon unlocking the driver door with the RKE, and opening that door. The current driver is identified when the RKE transmitter is used to unlock the driver door. See “Memory

Remote Recall” under Power Seat Adjustment on page 3‑4 for more information. Memory Remote Recall is when the memorized settings will be recalled as you unlock the vehicle. Press the MENU/SELECT knob when “Memory Remote Recall” is highlighted to toggle between “On” or “Off.” Press E BACK to confirm the selection and go back to the last menu. Return to Factory Settings Select “Return to Factory Settings” to return all of the vehicle personalization to the default