2008 Chevrolet Equinox Owners Manual

Download PDF Manual
conditions allow, the cruise control can be used again. Resuming a Set Speed If the cruise control is at the set speed desired and the brakes are applied, the cruise control shuts off. The cruise symbol in the instrument panel cluster also goes off indicating cruise is no longer engaged. To return to your previously set speed, you do not need to go through the set process again. Once you are driving about 25 mph (40 km/h) or more, press the +RES button on your steering wheel. The vehicle goes back to the previous set speed and stays there. 3-12 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed. (cid:127) Press and hold the +RES button on the steering wheel until the desired speed is reached, then release it. To increase vehicle speed in small amounts, press the +RES button. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) faster. Reducing Speed While Using Cruise Control To reduce your speed while using cruise control: (cid:127) Press and hold the SET– button on the steering wheel until the desired lower speed is reached, then release it. To slow down in very small amounts, push the SET− button on the steering wheel brieﬂy. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle’s speed. When you take your foot off the pedal, the vehicle slows down to the cruise control speed that was set earlier. (cid:127) (cid:127) Using Cruise Control on Hills How well your cruise control works on hills depends upon the vehicle’s speed, load, and the steepness of the hills. While going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed. While going downhill, you might have to brake or shift to a lower gear to keep the vehicle at a lower speed. However, when the brakes are applied the cruise control turns off. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are three ways to end cruise control: (cid:127) Step lightly on the brake pedal. (cid:127) Press the [ button on the steering wheel. (cid:127) Press the J button on the steering wheel. Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off. Headlamps The exterior lamp control is located on the turn signal/multifunction lever. O(Exterior Lamp Control): Turn the control with this symbol on it to operate the exterior lamps. The exterior lamp control has the following positions: AUTO (Off/Automatic Headlamps): Turn the control to this position to put the headlamps in automatic mode. Automatic mode will turn the exterior lamps on and off depending upon how much light is available outside of the vehicle. ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: (cid:127) Sidemarker Lamps Taillamps License Plate Lamps Instrument Panel Lights 53(Headlamps): Turning the control to this position turns on the headlamps, together with the previously listed lamps and lights. Headlamps on Reminder If you open the driver’s door with the ignition off and the lamps on, you will hear a warning chime. 3-13 (cid:127) (cid:127) (cid:127) When the headlamps are turned off, the regular lamps will go off, and the low-beam headlamps come on to the reduced brightness. To idle your vehicle with the DRL off, move the shift lever to PARK (P). The DRL will stay off until the shift lever is moved out of the PARK (P) position. The regular headlamp system should be turned on when needed. Automatic Headlamp System When it is dark enough outside and the exterior lamps control is in the automatic position, the headlamps will come on automatically. See Headlamps on page 3-13. Your vehicle has a light sensor located on top of the instrument panel. Make sure it is not covered, or the headlamps will be on when you do not need them. The system may also turn on the headlamps when driving through a parking garage or tunnel. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional Daytime Running Lamps (DRL) are required on all vehicles ﬁrst sold in Canada. The DRL system will make your low-beam headlamps come on at a reduced brightness in daylight when the following conditions are met: The ignition is on. The exterior lamp band is in the automatic position. The transmission is not in PARK (P). The light sensor determines it is daytime. The parking brake is released. When the DRL are on, the low-beam headlamps will be on at a reduced brightness. The taillamps, sidemarker and other lamps will not be on. The instrument panel will not be lit up either. When the exterior lamp band is turned to the headlamp position, the low-beam headlamps come on. The other lamps that come on with the headlamps will also come on. 3-14 (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Fog Lamps If your vehicle has this feature, use the fog lamps for better visibility in foggy or misty conditions. Instrument Panel Brightness This feature controls the brightness of the instrument panel lights. The fog lamps button is located on the instrument panel above the radio. The control for this feature is located on the instrument panel to the left of the steering column. To use the fog lamps, the parking lamps or low-beam headlamps must be on. Push the button to turn the fog lamps on or off. The fog lamp button is lit when the lamps are on. The fog lamps will go off whenever the high-beam headlamps are turned on. When the high-beam headlamps are turned off, the fog lamps will come on again. Some localities have laws that require the headlamps to be on along with the fog lamps. Turn the control up to brighten the lights or down to dim them. 3-15 Dome Lamp If the vehicle has a dome lamp with a switch, the following are the settings. 9(Off): Move the lever to this position to turn the lamp off, even when a door is open. 1(Door): Move the lever to this position so that the lamp comes on when a door is opened. +(On): Move the lever to this position to turn the dome lamp on. Entry Lighting The dome lamp and the cargo lamp inside the vehicle comes on when any door is opened, if the dome lamp is in the door position. In addition, these lamps come on when the Remote Keyless Entry (RKE) unlock button is pressed. It stays on for 20 seconds or until a door is opened. After the door is opened and then closed, the light remains on for 20 seconds, or until the key is put in the ignition and turned to the ON/RUN position. 3-16 Map Lamps Your vehicle may have lamps located on the headliner above the rearview mirror. Push on the lens in the lamp to turn them on and off. Cargo Lamp The cargo lamp is located over the rear compartment, and is controlled by the dome lamp. See Dome Lamp on page 3-16. Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as Battery Saver Active or Service Battery Charging System. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 3-49. Battery Run-Down Protection Your vehicle has a battery saver feature designed to protect the vehicle’s battery. When any interior lamp is left on and the ignition is turned off, the battery rundown protection system will automatically turn the lamp off after 20 minutes. This will avoid draining the battery. This vehicle also has a retained accessory power feature. If the radio is on, it will turn off after 10 minutes or if any door on the vehicle is opened. See Retained Accessory Power (RAP) on page 2-21. 3-17 If electrical devices are left plugged into a Accessory Power Outlet(s) The accessory power outlets can be used to connect electrical equipment such as a cellular phone or CB radio. The two accessory power outlets are located in the front and at the rear of the center console storage area. To use the outlets, remove the cover. When not in use, always cover the outlet with the protective cap. Notice: power outlet, the battery may drain causing your vehicle not to start or damage to the battery. This would not be covered by the warranty. Always unplug all electrical devices when turning off your vehicle. Certain electrical accessories may not be compatible with the accessory power outlets and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on the accessory power outlet. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. 3-18 When adding electrical equipment, be sure to follow the installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Ashtray(s) and Cigarette Lighter Your vehicle may have a removable ashtray and cigarette lighter. The ashtray can be placed into the front console cupholders. To use the lighter, push it in all the way and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Do not use equipment exceeding maximum amperage rating of 15 amperes. Notice: If you put papers, pins, or other ﬂammable items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. Climate Controls Climate Control System The heating, cooling, and ventilation for the vehicle can be controlled with this system. If your vehicle has the remote start feature, the climate control system functions as part of the remote start feature. See Remote Keyless Entry (RKE) System Operation on page 2-5. Operation 9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. In any setting other than off, the fan runs continuously with the ignition on. To turn off the air completely, turn the fan to 0 and select the recirculation button. Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the temperature inside the vehicle. Use the right knob to select from the following modes: There is one position between each mode to ﬁnely adjust airﬂow position. H(Vent): This mode directs air to the instrument panel outlets. )(Bi-Level): This mode splits the air between the instrument panel outlets and the ﬂoor outlets. 6(Floor): This mode directs most of the air to the ﬂoor outlets with some air directed to the windshield and side windows. The right knob may also be used to select the defrost and defog modes that are described in this section. You can also select modes by using the following buttons: ; (Outside Air): Press this button to turn the outside air mode on. When this mode is on, outside air will circulate throughout the vehicle. When the button is pressed, an indicator light in the button comes on to show that it is activated. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode. 3-19 @ (Recirculation): Press this button to recirculate cabin air through the vehicle. It can be used to prevent outside air and odors from entering the vehicle or to help heat or cool the air inside the vehicle more quickly. An indicator light will come on in this mode. Operation in this mode during periods of high humidity and cool outside temperatures may result in increased window fogging. If window fogging is experienced, select the defrost mode. The recirculation mode cannot be used with ﬂoor, defrost, or defogging modes. If you try to select recirculation in one of those modes, the indicator light ﬂashes several times and turns off. #(Air Conditioning): Press this button to turn the air conditioning system on or off. When this button is pressed, an indicator light on the button comes on to show that the air conditioning is activated. The air conditioning can be selected in any mode as long as the fan switch is on. The air conditioning compressor does not operate when outside temperatures fall below 38°F (3°C). The indicator light ﬂashes several times and turns off when outside conditions affect air conditioning operation. This is normal. On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for the vehicle to cool down. It also helps the system to operate more efficiently. For quick cool down on hot days, select the following settings together: 1. Vent mode. 2. Outside air. 3. Air conditioning. 4. The coolest temperature. 5. The highest fan speed. 6. Once the vehicle’s interior temperature is below the outside temperature, select recirculation mode for enhanced cooling. Using these settings together for long periods of time may cause the air inside of the vehicle to become too dry. To prevent this from happening, after the air inside of the vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so a small amount of water might drip underneath the vehicle while idling or after turning off the engine. This is normal. ( (Heated Seats): If your vehicle has heated seats, see Heated Seats on page 1-4. 3-20 Defogging and Defrosting Fog or frost on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. When either of these modes are selected, the system runs the air conditioning compressor and cancels the recirculation mode to dry the air. For best results, clear all snow and ice from the windshield before defrosting. Turn the right knob to select the defog or defrost mode. -(Defog): This mode directs half of the air to the windshield and the side window outlets, and half to the ﬂoor outlets. 0(Defrost): This mode directs most of the air to the windshield and the side window outlets, with some air directed to the ﬂoor outlets. Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. The rear window defogger only works when the ignition is in ON/RUN. <(Rear): Press this button to turn the rear window defogger on or off. An indicator light on the button comes on to show that the rear window defogger is activated. The rear window defroster stays on for about 10 minutes if the vehicle remains at slower vehicle speeds or until the button is pressed, or unless the ignition is turned to ACC/ACCESSORY or LOCK/OFF. If turned on again, the defogger only runs for about ﬁve minutes before turning off again. At higher vehicle speeds, the defogger may stay on continuously. The defogger can always be turned off by pressing the button again or by turning off the ignition. 3-21 If your vehicle has the remote start feature, the rear defogger automatically turns on if it is cold outside. When the vehicle transitions out of the remote start mode, the rear defogger will turn off. See Remote Keyless Entry (RKE) System Operation on page 2-5. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. Remote Start Climate Control Operation If your vehicle has the remote start feature and it is activated, the climate control system heats and cools the inside of the vehicle using the modes that were set before the vehicle was turned off and the rear defogger automatically turns on. If your vehicle has heated seats, they may turn on if it is cold outside and will shut off when the key is turned to ON/RUN. See Heated Seats on page 1-4. 3-22 Outlet Adjustment Use the louvers located on the air outlets to change the direction of the airﬂow. Operation Tips (cid:127) Clear away any ice, snow, or leaves from the air inlets at the base of the vehicle that may block the ﬂow of air into your vehicle. (cid:127) Do not use any non-GM approved hood deﬂectors that could adversely affect the performance of the system. (cid:127) Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively. Passenger Compartment Air Filter Outside air is routed through a passenger compartment air ﬁlter before entering the vehicle. This ﬁlter removes certain particles from the air, including pollen and dust particles. Reductions in airﬂow, which may occur more quickly in dusty areas, indicate that the ﬁlter needs to be replaced early. The ﬁlter should be replaced as part of routine scheduled maintenance. See Scheduled Maintenance on page 6-4 for when to replace the ﬁlter. To change the passenger compartment air ﬁlter, use the following steps: 1. The passenger’s side air inlet panel is located below the center of the passenger’s side wiper blade. Remove the push pin retaining the air inlet panel. Pry the center of the push pin out 0.5 in (13 mm) for removal. 2. Open the hood. 3. Remove the three push pins from the top and forward edge of the passenger’s side air inlet panel. 4. Remove the air inlet panel to access the ﬁlter. 5. Press the release tab on the driver’s side of the ﬁlter and pull out the edge of the ﬁlter. 6. Remove the ﬁlter from the vehicle. 7. Install a new passenger compartment air ﬁlter. For the type of ﬁlter to use see Maintenance Replacement Parts on page 6-14. 8. Reverse Steps 1 through 5. 3-23 Warning Lights, Gages, and Indicators This section describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the following pages, some warning lights come on brieﬂy when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there is a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly and even dangerous. So please get to know your warning lights and gages. They are a big help. 3-24 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you are using, and many other things you will need to drive safely and economically. United States version shown, Canada and Sport Model similar 3-25 Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper resistant odometer. The digital odometer will read 999,999 if someone tries to turn it back. You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set to the mileage total of the old odometer, then it must be. If not, then it is set at zero and a label must be put on the driver’s door to show the old mileage reading when the new odometer was installed. Trip Odometer Your trip odometer is located in the Driver Information Center and shows how far your vehicle has been driven since the trip odometer was last reset. For more information see DIC Operation and Displays on page 3-43. Tachometer The tachometer shows your engine speed in revolutions per minute (rpm). Notice: tachometer in the solid red area, your vehicle could be damaged. The damages would not be covered by your warranty. Do not operate the engine in the solid red area. If you operate the engine with the 3-26 Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. This chime and light is repeated if the driver remains unbuckled and the vehicle is in motion. If the driver’s belt is already buckled, neither the chime nor the light will come on. Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-65 for more information. The passenger safety belt light, located on the instrument panel, will come on and stay on for several seconds and then ﬂash for several more. This chime and light are repeated if the passenger remains unbuckled and the vehicle is in motion. If the passenger’s safety belt is buckled, neither the chime nor the light will come on. Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-56. 3-27 If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your instrument panel has a passenger airbag status indicator. {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should ﬂash for a few seconds when you start the engine. If the light does not come on then, have it ﬁxed immediately. If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message may also come on. See DIC Warnings and Messages on page 3-49 for more information. 3-28 United States Canada When you start the vehicle, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag is enabled (may inﬂate). {CAUTION: {CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Do not use a rear-facing child restraint in the right front passenger’s seat if the airbag is turned on. Even though the passenger sensing system is designed to turn off the right front passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be secured in the rear seat, even if the airbag is off. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag. See Passenger Sensing System on page 1-65 for more on this, including important safety information. 3-29 If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. {CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the airbag(s). See Airbag Readiness Light on page 3-27 for more on this, including important safety information. Charging System Light If this light comes on while you are driving, you may have a problem with the charging system. A charging system Driver Information Center (DIC) message may also appear. See DIC Warnings and Messages on page 3-49 for more information. This light could indicate that you have problems with a generator drive belt, or another electrical problem. Have it checked right away. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and air conditioner. 3-30 Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the brake system warning light comes on, there is a brake problem. Have your brake system inspected right away. United States Canada The brake light is located in the instrument panel cluster. This light should come on brieﬂy when you turn the ignition key to RUN. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. When the ignition is on, the brake light will come on when you set your parking brake. The light will stay on if your parking brake does not release fully. A chime will also sound if the parking brake is not fully released and the vehicle is moving. If it stays on after your parking brake is fully released, it means you have a brake problem. The brake light will also come on to indicate a low brake ﬂuid level. See Brakes on page 5-33 for more information. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push or the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-28. {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service. 3-31 Antilock Brake System Warning Light Traction Control System (TCS) Warning Light For vehicles with the Antilock Brake System (ABS), this light will come on brieﬂy when you start the engine. Your vehicle has a Traction Control System (TCS) and StabiliTrak® warning light. That is normal. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If the ABS light stays on, turn the ignition off, if the light comes on when you are driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light still stays on, or comes on again while you are driving, your vehicle needs service. If the regular brake system warning light is not on, you still have brakes, but you do not have antilock brakes. If the regular brake system warning light is also on, you do not have antilock brakes and there is a problem with your regular brakes. See Brake System Warning Light on page 3-31 For vehicles with a Driver Information Center (DIC), see DIC Warnings and Messages on page 3-49 for all brake related DIC messages. 3-32 When the traction control is activated the light will ﬂash when the TCS is limiting wheel spin or when the StabiliTrak® system is active. You may feel or hear the system working, but this is normal. This light may also come on after extended heavy braking indicating the brakes have become too hot to limit wheel spin. This light will come on and stay on if the TCS is turned off using the traction control on/off button, located next to the gear shift lever. If the TCS warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service. See Traction Control System (TCS) on page 4-6 and StabiliTrak® System on page 4-7 for more information. Engine Coolant Temperature Warning Light The engine coolant temperature warning light will come on when the engine has overheated. Engine Coolant Temperature Gage This gage measures the temperature of the vehicle’s engine. If this happens you should pull over and turn off the engine as soon as possible. See Engine Overheating on page 5-24 for more information. Notice: Driving with the engine coolant temperature warning light on could cause your vehicle to overheat. See Engine Overheating on page 5-24. Your vehicle could be damaged, and it might not be covered by your warranty. Never drive with the engine coolant temperature warning light on. If the indicator needle moves into the shaded area, the engine is too hot. A temperature indicator light will turn on. If you have been operating your vehicle under normal driving conditions, and the temperature indicator light comes on, you should pull off the road, stop your vehicle and turn off the engine as soon as possible. 3-33 Tire Pressure Light This light comes on brieﬂy when the engine is started. This light will also come on when one or more of your tires are signiﬁcantly underinﬂated. A tire pressure message in the Driver Information Center (DIC), may accompany the light. See DIC Warnings and Messages on page 3-49 for more information. Stop and check your tires as soon as it is safe to do so. If underinﬂated, inﬂate to the proper pressure. See Tires on page 5-52 for more information. If a problem is detected with the Tire Pressure Monitor System, this light will ﬂash for approximately 60 seconds and then stay on solid for the remainder of the ignition cycle. See Tire Pressure Monitor System on page 5-62 for more information. 3-34 Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. This can prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. Notice: this light on, after a while, the emission controls might not work as well, your vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by your warranty. If you keep driving your vehicle with Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and can cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by your warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 5-3. This light comes on, as a check to show it is working, when the ignition is turned ON/RUN but the engine is not running. If the light does not come on, have it repaired. This light also comes on during a malfunction in one of two ways: Light Flashing — A misﬁre condition has been detected. A misﬁre increases vehicle emissions and could damage the emission control system on your vehicle. Diagnosis and service might be required. Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service might be required. If the Light is Flashing The following can prevent more serious damage to your vehicle: (cid:127) Reduce vehicle speed. (cid:127) Avoid hard accelerations. (cid:127) Avoid steep uphill grades. If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the ignition off, wait at least 10 seconds, and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still ﬂashing, follow the previous steps and see your dealer/retailer for service as soon as possible. 3-35 (cid:127) (cid:127) (cid:127) If the Light Is On Steady You might be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality causes the engine not to run as efficiently as designed. You might notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration — these conditions might go away once the engine is warmed up. This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer/retailer can check the vehicle. Your dealer/retailer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that might have developed. 3-36 Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced the battery or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your dealer/retailer can prepare the vehicle for inspection. Oil Pressure Light {CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil. This light will come on brieﬂy when you start your engine. If it does not, have your vehicle serviced. When the light comes on and stays on, it means that oil is not ﬂowing through your engine properly. You could be low on oil and you might have some other system problem. 3-37 Change Engine Oil Light Fog Lamp Light If this light comes on and stays on for 30 seconds, it means that service is required for your vehicle. The fog lamp light will come on when the fog lamps are in use. A CHANGE OIL SOON message will appear on the DIC. For more information see DIC Warnings and Messages on page 3-49. After having the oil changed you will need to reset the light. See Engine Oil on page 5-15, and Scheduled Maintenance on page 6-4 for more information. Security Light The light will go out when the fog lamps are turned off. See Fog Lamps on page 3-15 for more information. Cruise Control Light This light comes on whenever you set the cruise control. For information regarding this light and the vehicle’s security system, see Content Theft-Deterrent on page 2-17, and PASS-Key® III+ Operation on page 2-18. The light goes out when the cruise control is turned off. See Cruise Control on page 3-10 for more information. 3-38 Reduced Engine Power Light Highbeam On Light Your vehicle has a reduced engine power light. This light comes on when the high-beam headlamps are in use. This light, along with the service vehicle soon light, will be displayed when a noticeable reduction in the vehicle’s performance may occur. Stop the vehicle and turn off the ignition. Wait for 10 seconds and restart your vehicle. This may correct the condition. See Service Vehicle Soon Light on page 3-41 for more information. The vehicle may be driven at a reduced speed when the reduced engine power light is on, but acceleration and speed may be reduced. The performance may be reduced until the next time you drive your vehicle. If this light stays on, see your dealer/retailer as soon as possible for diagnosis and repair. See Headlamp High/Low-Beam Changer on page 3-8 for more information. Service All-Wheel Drive Light This light is located in the center of your instrument panel cluster. This light and the SERVICE ALL WHEEL DRIVE message in the Driver Information Center (DIC) will come on and stay on to indicate that there may be a problem with the drive system and service is required. 3-39 See All-Wheel Drive (AWD) System on page 4-8 and DIC Warnings and Messages on page 3-49 for more information. All-Wheel Drive Disabled Light This light will come on when the rear drive system is overheating. Gate Ajar Light If this light comes on, your liftgate is not completely closed. Driving with the liftgate open can cause carbon monoxide (CO) to enter the vehicle. An ALL WHEEL DRIVE OFF message will appear in the Driver Information Center (DIC) too. This light will turn off when the rear drive system cools down. If this light stays on for a while, you need to reset the light. To reset the light, turn the ignition off and then back on again. If the light stays on, see your dealer/retailer right away. See All-Wheel Drive on page 5-42 and DIC Warnings and Messages on page 3-49 for more information. See Engine Exhaust on page 2-35 for more information. Door Ajar Light This light will come on when a door is ajar. Do not drive with a door ajar. 3-40 Service Vehicle Soon Light For vehicles with this light, it will come on if a condition exists that may require the vehicle to be taken in for service. If the light comes on, see your dealer/retailer for service as soon as possible. Fuel Gage When the ignition is on, the fuel gage tells you about how much fuel you have left in your tank. When the indicator nears empty, the low fuel light will come on. You still have a little fuel left, but you should get more soon. See Low Fuel Warning Light on page 3-42 for more information. Here are four things that some owners ask about. None of these show a problem with your fuel gage: (cid:127) At the service station, the fuel pump shuts off before the gage reads full. It takes a little more or less fuel to ﬁll up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to ﬁll the tank. The gage moves a little when you turn a corner or speed up. The gage takes a few seconds to stabilize after the ignition is turned on, and will go back to empty when you turn the ignition off. For your fuel tank capacity, see Capacities and Speciﬁcations on page 5-107. 3-41 (cid:127) (cid:127) (cid:127) Low Fuel Warning Light This light is located in the fuel gage. For more information see Fuel Gage on page 3-41. This light comes on when the fuel tank is low on fuel. When you add fuel the light should go off. If it does not, have your vehicle serviced. A “Fuel Level LOW” message also appears in the Driver Information Center (DIC). See Fuel Gage on page 3-41 for more information. Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). All messages will appear in the DIC display located in the center of the instrument panel cluster. The DIC buttons are located on the center of the instrument panel. The DIC comes on when the ignition is on. After a short delay, the DIC will display the information that was last displayed before the engine was turned off. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected. The top of the DIC display shows the shift lever position indicator. See Automatic Transmission Operation (3.4L V6 with 5-Speed) on page 2-24 or Automatic Transmission Operation (3.6L V6 with 6-Speed) on page 2-27 for more information. If your vehicle has these feature, the DIC also displays the compass direction and the outside air temperature when viewing the trip and fuel information. If there is a problem with the system that controls the temperature display, the numbers will be replaced with dashes. If this occurs, have the vehicle serviced by your dealer/retailer. If an abnormal temperature reading is displayed for an extended period of time, consult your dealer/retailer. Under certain circumstances, especially when the engine is idling, a delay updating the temperature display is normal. The DIC also allows some features to be personalized. See DIC Vehicle Personalization on page 3-58 for more information. 3-42 DIC Operation and Displays The DIC has different displays which can be accessed by pressing the DIC buttons located on the center of the instrument panel. DIC Buttons The buttons are the trip/fuel, vehicle information, and set/reset buttons. The button functions are detailed in the following pages. 3 (Trip/Fuel): Press this button to scroll through the trip and fuel displays. See “Trip/Fuel Menu Items” following for more information on these displays. T (Vehicle Information): Press this button to scroll through the vehicle information displays and to personalize the feature settings on your vehicle. See “Vehicle Information Menu Items” following and DIC Vehicle Personalization on page 3-58 for more information on these displays. V (Set/Reset): Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC. Trip/Fuel Menu Items 3 (Trip/Fuel): Press this button to scroll through the following displays: ODOMETER Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km). This display will also show the outside air temperature in either degrees Fahrenheit (°F) or degrees Celsius (°C). To change the DIC display to English or metric units, see “UNITS” later in this section. TRIP Press the trip/fuel button until TRIP displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for the trip odometer. This display will also show the outside air temperature in either degrees Fahrenheit (°F) or degrees Celsius (°C). The trip odometer can be reset to zero by pressing the set/reset button while the trip odometer is displayed. 3-43 AVG (Average) SPD (Speed) Press the trip/fuel button until AVG (Average) SPD (Speed) displays. This display shows the average speed of the vehicle in miles per hour (mph) or kilometers per hour (km/h). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. To reset the value, press and hold the set/reset button. The display will return to zero. AVG (Average) ECON (Economy) Press the trip/fuel button until AVG (Average) ECON (Economy) displays. This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this menu item was reset. To reset this display, press and hold the set/reset button. The display will return to zero. RANGE Press the trip/fuel button until RANGE displays. This display shows the approximate number of remaining miles (mi) or kilometers (km) the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle’s fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This estimate will change if driving conditions change. For example, if driving in traffic and making frequent 3-44 stops, this display may read one number, but if the vehicle is driven on a freeway, the number may change even though the same amount of fuel is in the fuel tank. This is because different driving conditions produce different fuel economies. Generally, freeway driving produces better fuel economy than city driving. If your vehicle is low on fuel, the FUEL LEVEL LOW message will be displayed. See “FUEL LEVEL LOW” under DIC Warnings and Messages on page 3-49 for more information. Blank Display This display shows no information. Vehicle Information Menu Items T (Vehicle Information): Press this button to scroll through the following displays: OIL LIFE Press the vehicle information button until OIL LIFE REMAINING displays. This display shows an estimate of the oil’s remaining useful life. If you see 99% OIL LIFE REMAINING on the display, that means 99% of the current oil life remains. The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display along with the Change Engine Oil Light on the instrument panel cluster. See “CHANGE ENGINE OIL SOON” under DIC Warnings and Messages on page 3-49 and Change Engine Oil Light on page 3-38. You should change the oil as soon as possible. See Engine Oil on page 5-15. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 6-4 for more information. Remember, you must reset the OIL LIFE yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, see Engine Oil Life System on page 5-18. UNITS Press the vehicle information button until UNITS displays. This display allows you to select between English or Metric units of measurement. Once in this display, press the set/reset button to select between ENGLISH or METRIC units. FRONT TIRES or REAR TIRES The pressure for each tire can be viewed in the DIC. The tire pressure will be shown in either pounds per square inch (psi) or kilopascals (kPa). Press the vehicle information button until the DIC displays FRONT TIRES PSI (kPa) LF ## RF ##. Press the vehicle information button again until the DIC displays REAR TIRES PSI (kPa) LR ## RR ##. If a low or high tire pressure condition is detected by the system while driving, a message advising you to check the pressure in a speciﬁc tire will appear in the display. See Inﬂation - Tire Pressure on page 5-59 and DIC Warnings and Messages on page 3-49 for more information. If the tire pressure display shows dashes instead of a value, there may be a problem with your vehicle. If this consistently occurs, see your dealer/retailer for service. BATTERY Press the vehicle information button until BATTERY displays. This display shows the current battery voltage. If the voltage is normal, the display will show NORMAL. If the voltage is low or high, the display will show LOW or HIGH. Your vehicle’s charging system regulates voltage based on the state of the battery. The battery voltage may ﬂuctuate when viewing this information on the DIC. This is normal. See Charging System Light on page 3-30 for more information. 3-45 If there is a problem with the battery charging system, the DIC will display SERVICE BATTERY CHARGING SYSTEM. See “SERVICE BATTERY CHARGING SYSTEM” under DIC Warnings and Messages on page 3-49. Also, see Electric Power Management on page 3-17 for more information. LEARN REMOTE KEY This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. To match an RKE transmitter to your vehicle: 1. Make sure the vehicle is in PARK (P). 2. Press the vehicle information button until LEARN REMOTE KEY PRESS V TO BEGIN displays. 3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE is displayed. 4. Press and hold the lock and unlock buttons on the ﬁrst transmitter at the same time for about 15 seconds. A chime will sound indicating that the transmitter is matched. 5. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of four transmitters matched to it. 6. To exit the programming mode, you must cycle the key to LOCK/OFF. 3-46 CALIBRATE COMPAS (Compass) Your vehicle may have this feature. The compass can be manually calibrated. To calibrate the compass through the DIC, see DIC Compass on page 3-46. CHANGE COMPASS ZONE Your vehicle may have this feature. To change the compass zone through the DIC, see DIC Compass on page 3-46. Blank Display This display shows no information. FEATURE SETTNGS (Settings): PRESS V TO SELCT (Select) This display allows you to personalize the feature settings on your vehicle. See DIC Vehicle Personalization on page 3-58 for more information. DIC Compass Your vehicle may have a compass in the Driver Information Center (DIC). Compass Zone The zone is set to zone eight upon leaving the factory. Your dealer/retailer will set the correct zone for your location. Under certain circumstances, such as during a long distance cross-country trip or moving to a new state or province, it will be necessary to compensate for compass variance by resetting the zone through the DIC if the zone is not set correctly. Compass variance is the difference between the earth’s magnetic north and true geographic north. If the compass is not set to the zone where you live, the compass may give false readings. The compass must be set to the variance zone in which the vehicle is traveling. To adjust for compass variance, use the following procedure: Compass Variance (Zone) Procedure 1. Do not set the compass zone when the vehicle is moving. Only set it when the vehicle is in PARK (P). Press the vehicle information button until PRESS V TO CHANGE COMPASS ZONE displays. 2. Find the vehicle’s current location and variance zone number on the map. Zones 1 through 15 are available. 3. Press the set/reset button to scroll through and select the appropriate variance zone. 4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. 5. If calibration is necessary, calibrate the compass. See “Compass Calibration Procedure” following. 3-47 Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. It is suggested to calibrate away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible. If CAL should ever appear in the DIC display, the compass should be calibrated. If the DIC display does not show a heading, for example, N for North, or the heading does not change after making turns, there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic CB or cell phone antenna mount, a magnetic emergency light, magnetic note pad holder, or any other magnetic item. Turn off the vehicle, move the magnetic item, then turn on the vehicle and calibrate the compass. To calibrate the compass, use the following procedure: Compass Calibration Procedure 1. Before calibrating the compass, make sure the compass zone is set to the variance zone in which the vehicle is located. See “Compass Variance (Zone) Procedure” earlier in this section. Do not operate any switches such as window, sunroof, climate controls, seats, etc. during the calibration procedure. 2. Press the vehicle information button until PRESS V TO CALIBRATE COMPAS (Compass) displays. 3. Press the set/reset button to start the compass calibration. 4. The DIC will display CALIBRATING: DRIVE IN CIRCLES. Drive the vehicle in tight circles at less than 5 mph (8 km/h) to complete the calibration. The DIC will display CALIBRATION COMPLETE for a few seconds when the calibration is complete. The DIC display will then return to the previous menu. 3-48 DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action, but you can press the set/reset button to acknowledge that you received the messages and to clear them from the display. Pressing any of the DIC buttons also acknowledge and clear any messages. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear, not correct the problem. The following are the possible messages that can be displayed and some information about them. ALL WHEEL DRIVE OFF If your vehicle has the All-Wheel Drive (AWD) system, this message displays along with the All-Wheel Drive Disabled light when the rear drive system is overheating. This message turns off when the rear drive system cools down. If the warning message stays on for a while, you need to reset the warning message. To reset the warning message, turn the ignition off and then back on again. If the message stays on, see your dealer/retailer right away. See All-Wheel Drive (AWD) System on page 4-8 and All-Wheel Drive Disabled Light on page 3-40 for more information. BATTERY SAVER ACTIVE This message displays when the charging system detects that the battery is being drained. You may notice that the vehicle attempts to reduce the drain for you by turning off accessories, such as interior fans, rear defogger, and heated seats. Turn off all accessories. If the vehicle is not running, start and run the engine for at least 10 minutes to allow the battery to recharge. If the engine is running and the condition persists, see your dealer/retailer. See Electric Power Management on page 3-17 for more information. 3-49 BUCKLE PASSENGER SEATBELT This message reminds you to buckle the passenger’s safety belt. See Passenger Sensing System on page 1-65. This message displays and a chime sounds when the ignition is on, the driver’s safety belt is buckled, the passenger’s safety belt is unbuckled with the passenger airbag enabled, and the vehicle is in motion. You should have the passenger buckle their safety belt. This reminder will be repeated if the ignition is on, the vehicle is in motion, the driver is buckled and the passenger is still unbuckled, and the passenger airbag is enabled. If the passenger’s safety belt is already buckled, this message and chime will not come on. BUCKLE SEATBELT This message reminds you to buckle the driver’s safety belt. This message displays and a chime sounds when the ignition is on, the driver’s safety belt is unbuckled, and the vehicle is in motion. You should buckle your safety belt. If the driver remains unbuckled when the ignition is on and the vehicle is in motion, the reminder will be repeated. If the driver’s safety belt is already buckled, this message and chime will not come on. 3-50 This message is an additional reminder to the Safety Belt Reminder Light in the instrument panel cluster. See Safety Belt Reminders on page 3-27. CALIBRATING: DRIVE IN CIRCLES This message displays when calibrating the compass. Drive the vehicle in circles at less than 5 mph (8 km/h) to complete the calibration. See DIC Compass on page 3-46 for more information. CALIBRATION COMPLETE This message displays when the compass calibration is complete. See DIC Compass on page 3-46 for more information. CHANGE ENGINE OIL SOON This message displays and the Change Engine Oil Light in the instrument panel cluster turns on when service is required for the vehicle. See your dealer/retailer. See Change Engine Oil Light on page 3-38, Engine Oil on page 5-15 and Scheduled Maintenance on page 6-4 for more information. Acknowledging this message will not reset the OIL LIFE REMAINING display. That must be done at the OIL LIFE screen under the vehicle information menu. See “OIL LIFE” under DIC Operation and Displays on page 3-43 and Engine Oil Life System on page 5-18 for more information. CHECK TIRE PRESSURE This message displays when the pressure in one or more of the vehicle’s tires needs to be checked. This message also displays LEFT FRONT, RIGHT FRNT (Front), LEFT REAR, or RIGHT REAR to indicate which tire needs to be checked. You can receive more than one tire pressure message at a time. To read the other messages that may have been sent at the same time, press the set/reset button. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Tires on page 5-52, Loading Your Vehicle on page 4-22, and Inﬂation - Tire Pressure on page 5-59. The DIC also shows the tire pressure values. See DIC Operation and Displays on page 3-43. If the tire pressure is low, the low tire pressure warning light comes on. See Tire Pressure Light on page 3-34. DRIVER DOOR OPEN This message displays when the driver door is not closed properly. Close the door completely. ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor is automatically turned off. When the coolant temperature returns to normal, the A/C operation automatically resumes. You can continue to drive your vehicle. ENGINE OVERHEATD (Overheated) IDLE ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed. See Engine Overheating on page 5-24 for more information. This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. 3-51 ENGINE OVRHEATD (Overheated) STOP ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. See Engine Overheating on page 5-24 for more information. This message displays along with a continuous chime when the engine has overheated. Stop and turn the engine off immediately to avoid severe engine damage. See Engine Overheating on page 5-24. ENGINE POWER IS REDUCED This message displays when the vehicle’s engine power is reduced. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer/retailer for service as soon as possible. FUEL LEVEL LOW This message displays and the Low Fuel Warning Light in the instrument panel cluster comes on when your vehicle is low on fuel. Reﬁll the fuel tank as soon as possible. See Fuel Gage on page 3-41, Low Fuel Warning Light on page 3-42, and Filling the Tank on page 5-8 for more information. HOOD OPEN This message displays on some vehicles when the hood is not closed properly. Close the hood completely. See Hood Release on page 5-11. ICE POSSIBLE DRIVE WITH CARE This message displays when the outside air temperature is cold enough to create icy road conditions. Adjust your driving accordingly. LIFTGATE OPEN This message displays when the liftgate is not closed completely. Close the liftgate completely. See Liftgate on page 2-13. 3-52 If you drive your vehicle while the engine OIL PRSSURE (Pressure) LOW STOP ENGINE Notice: oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the Driver Information Center (DIC), stop the vehicle as soon as possible. Do not drive the vehicle until the cause of the low oil pressure is corrected. See Engine Oil on page 5-15 for more information. This message displays when the vehicle’s engine oil pressure is low. The oil pressure light also appears on the instrument panel cluster. See Oil Pressure Light on page 3-37. Stop the vehicle immediately, as engine damage can result from driving a vehicle with low oil pressure. Have the vehicle serviced by your dealer/retailer as soon as possible when this message is displayed. PASSENGER DOOR FRONT/REAR OPEN This message displays when one or more of the passenger doors are not closed properly. Close the doors completely. REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “LEARN REMOTE KEY” under DIC Operation and Displays on page 3-43 for more information. SERVICE A/C (Air Conditioning) SYSTEM This message displays when there is a problem detected in the air conditioning system. Have the vehicle serviced by your dealer/retailer. SERVICE AIR BAG This message displays when there is a problem with the airbag system. Have your vehicle serviced by your dealer/retailer immediately. See Airbag Readiness Light on page 3-27 for more information. 3-53 SERVICE ALL WHEEL DRIVE If your vehicle has the All-Wheel Drive (AWD) system, this message displays along with the service all-wheel drive light if a problem occurs with this system. See Service All-Wheel Drive Light on page 3-39. If this message appears, stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display. If the message is still displayed or appears again when you begin driving, the AWD system needs service. See your dealer/retailer. SERVICE BATTERY CHARGING SYSTEM This message displays when there is a problem with the generator and battery charging systems. Driving with this problem could drain the vehicle’s battery. Turn off all unnecessary accessories. Stop and turn off the vehicle as soon as it is safe to do so. Have the electrical system checked by your dealer/retailer immediately. Connecting a battery charger to your vehicle while the ignition is in any position other than LOCK/OFF may cause this message to appear. If you need to charge your vehicle, make sure that the key is in LOCK/OFF or out of the ignition during charging. SERVICE BRAKE SYSTEM This message displays and a chime sounds when the brake ﬂuid level is low. The brake system warning light also appears on the instrument panel cluster when this message appears on the DIC. See Brake System Warning Light on page 3-31. Have the brake system serviced by your dealer/retailer as soon as possible. SERVICE POWER STEERING On some vehicles, this message displays when a problem is detected with the power steering system. When this message is displayed, you may notice that the effort required to steer the vehicle increases or feels heavier, but you will still be able to steer the vehicle. Have your vehicle serviced by your dealer/retailer immediately. 3-54 SERVICE STABILITRAK This message displays if there has been a problem detected with the StabiliTrak® System. A warning light also appears on the instrument panel cluster. See Traction Control System (TCS) Warning Light on page 3-32. See StabiliTrak® System on page 4-7 for more information. If this message turns on while you are driving, pull off the road as soon as possible and stop carefully. Try resetting the system by turning the ignition off and then back on. If this message still stays on or turns back on again while you are driving, your vehicle needs service. Have the StabiliTrak® System inspected by your dealer/retailer as soon as possible. SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system. A fault has been detected in the system which means that the system is disabled and it is not protecting the vehicle. The vehicle usually restarts; however, you may want to take the vehicle to your dealer/retailer before turning off the engine. See PASS-Key® III+ Operation on page 2-18 for more information. SERVICE TIRE MONITOR SYSTEM This message displays if a part on the Tire Pressure Monitor System (TPMS) is not working properly. The tire pressure light also ﬂashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 3-34. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 5-63 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer/retailer. SERVICE TRACTION CONTROL This message displays when the Traction Control System (TCS) is not functioning properly. A warning light also appears on the instrument panel cluster. See Traction Control System (TCS) Warning Light on page 3-32 and Traction Control System (TCS) on page 4-6 for more information. Have the TCS serviced by your dealer/retailer as soon as possible. SERVICE VEHICLE SOON This message displays when a non-emissions related malfunction occurs. Have the vehicle serviced by your dealer/retailer as soon as possible. 3-55 STABILITRAK NOT READY This message may display and a warning light on the instrument panel cluster may be on after ﬁrst driving the vehicle and exceeding 30 mph (48 km/h) for 30 seconds. See Traction Control System (TCS) Warning Light on page 3-32. The StabiliTrak® System is not functional until the light has turned off. See StabiliTrak® System on page 4-7 for more information. STABILITRAK OFF This message displays any time the StabiliTrak® System turns off. When this message has been displayed, StabiliTrak® is no longer available to assist you with directional control of the vehicle. Adjust your driving accordingly. See StabiliTrak® System on page 4-7. This message displays only while the ignition is in ON/RUN. Any of the following conditions may cause the StabiliTrak® System to turn off: The StabiliTrak® System is turned off by pressing and holding the traction control button. See StabiliTrak® System on page 4-7 for more information. The battery is low. There is a StabiliTrak® System failure. See your dealer/retailer for service. STARTING DISABLD (Disabled) SERVICE THRTTLE (Throttle) This message displays if the starting of the engine is disabled due to the electronic throttle control system. Have your vehicle serviced by your dealer/retailer immediately. This message only appears while the ignition is in ON/RUN, and will not disappear until the problem is resolved. This message cannot be acknowledged. THEFT ATTEMPTED This message displays if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle. See Content Theft-Deterrent on page 2-17 for more information. 3-56 (cid:127) (cid:127) (cid:127) TIRE LEARNING ACTIVE This message displays when the Tire Pressure Monitor System (TPMS) is re-learning the tire positions on your vehicle. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor. See Tire Inspection and Rotation on page 5-67, Tire Pressure Monitor System on page 5-62, and Inﬂation - Tire Pressure on page 5-59 for more information. TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) turns off. See Traction Control System (TCS) on page 4-6 for more information. This message only displays while the ignition is in ON/RUN and disappears after 10 seconds, unless it is acknowledged or an urgent warning appears. Any of the following conditions may cause the TCS to turn off: The TCS is turned off by pressing the traction control button. See Traction Control System (TCS) on page 4-6 for more information. The battery is low. There is a TCS failure. See your dealer/retailer for service. TRACTION CONTROL ON This message displays when the Traction Control System (TCS) turns on. See Traction Control System (TCS) on page 4-6 for more information. TURN SIGNAL ON This message displays as a reminder to turn off the turn signal if you drive your vehicle for more than about 0.75 mile (1.2 km) with a turn signal on. See Turn Signal/Multifunction Lever on page 3-7. This message displays and a chime sounds only when the ignition is in ON/RUN. The message will not disappear until the turn signal is manually turned off, or a turn is completed. 3-57 (cid:127) (cid:127) (cid:127) DIC Vehicle Personalization Your vehicle has personalization capabilities that allow you to program certain features to one preferred setting. All of the personalization options may not be available on your vehicle. Only the options available will be displayed on the DIC. The default settings for the personalization features were set when your vehicle left the factory, but may have been changed from their default state since then. The personalization preferences are automatically recalled. To change personalization preferences, use the following procedure. Entering the Feature Settings Menu 1. Turn the ignition on and place the vehicle in PARK (P). To avoid excessive drain on the battery, it is recommended that the headlamps are turned off. 2. Press the vehicle information button until FEATURE SETTNGS (Settings): PRESS V TO SELCT (Select) appears on the DIC display. 3. Press the set/reset button to enter the feature settings menu. If the menu is not available, FEATURE SETTNGS (Settings): AVAILABLE IN PRK (Park) will display. Before entering the menu, make sure the vehicle is in PARK (P). Feature Settings Menu Items The following are personalization features that allow you to program settings to the vehicle: DISPLAY ENGLISH This feature will only display if a language other than English has been set. This feature allows you to change the language in which the DIC messages appear to English. Press the vehicle information button until the PRESS V TO DISPLAY ENGLISH screen appears on the DIC display. Press the set/reset button to display all DIC messages in English. DISPLAY LANG. (Language) This feature allows you to select the language in which the DIC messages will appear. 3-58 Press the vehicle information button until DISPLAY LANG. (Language) appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: ENGLISH (default): All messages will appear in English. FRENCH: All messages will appear in French. SPANISH: All messages will appear in Spanish. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. AUTO LOCK This feature allows you to select when the vehicle’s doors will automatically lock. See Programmable Automatic Door Locks on page 2-11 for more information. Press the vehicle information button until AUTO LOCK appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: OUT OF PARK (default): The vehicle’s doors automatically lock when the doors are closed and the vehicle is shifted out of PARK (P). AT SPEED: The vehicle’s doors automatically lock when the vehicle speed is above 5 mph (8 km/h) for three seconds. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. AUTO UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Programmable Automatic Door Locks on page 2-11 for more information. 3-59 Press the vehicle information button until AUTO UNLOCK appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: OFF: None of the doors will automatically unlock. DRIVER KEY OUT: Only the driver’s door will unlock when the key is taken out of the ignition. DRIVER IN PARK: Only the driver’s door will unlock when the vehicle is shifted into PARK (P). ALL AT KEY OUT: All of the doors will unlock when the key is taken out of the ignition. ALL IN PARK (default): All of the doors will unlock when the vehicle is shifted into PARK (P). NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. REMOTE LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if any of the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. Press the vehicle information button until REMOTE LOCK appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: HORN/LIGHTS OFF: There will be no feedback when you press the lock button on the RKE transmitter. LIGHTS ONLY: The exterior lamps will ﬂash when you press the lock button on the RKE transmitter. HORN CHIRP ONLY: The horn will sound on the second press of the lock button on the RKE transmitter. HORN/LIGHTS ON (default): The exterior lamps will ﬂash when you press the lock button on the RKE transmitter, and the horn will sound when the lock button is pressed again within ﬁve seconds of the previous command. 3-60 NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. REMOTE UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the RKE transmitter. You will not receive feedback when unlocking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. Press the vehicle information button until REMOTE UNLOCK appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: LIGHTS OFF: The exterior lamps will not ﬂash when you press the unlock button on the RKE transmitter. LIGHTS ON (default): The exterior lamps will ﬂash when you press the unlock button on the RKE transmitter. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. DELAY LOCK This feature allows you to select whether or not the locking of the vehicle’s doors and liftgate will be delayed. When locking the doors and liftgate with the power door lock switch and a door or the liftgate is open, this feature will delay locking the doors and liftgate until ﬁve seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. The key must be out of the ignition for this feature to work. You can temporarily override delayed locking by pressing the power door lock switch twice or the lock button on the RKE transmitter twice. See Delayed Locking on page 2-11 for more information. Press the vehicle information button until DELAY LOCK appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: LOCK DELAY OFF: There will be no delayed locking of the vehicle’s doors. LOCK DELAY ON (default): The doors will not lock until ﬁve seconds after the last door or the liftgate is closed. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-61 EXIT LIGHTNG (Lighting) This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the vehicle information button until EXIT LIGHTNG (Lighting) appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: OFF: The exterior lamps will not turn on. 30 SECONDS (default): The exterior lamps will stay on for 30 seconds. 1 MINUTE: The exterior lamps will stay on for one minute. 2 MINUTES: The exterior lamps will stay on for two minutes. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. APPRCH (Approach) LIGHTNG (Lighting) This feature allows you to select whether or not to have the exterior lights turn on brieﬂy during low light periods after unlocking the vehicle using the RKE transmitter. Press the vehicle information button until APPRCH (Approach) LIGHTNG (Lighting) appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: OFF: The exterior lights will not turn on when you unlock the vehicle with the RKE transmitter. ON (default): If it is dark enough outside, the exterior lights will turn on brieﬂy when you unlock the vehicle with the RKE transmitter. The lights will remain on for 20 seconds or until the lock button on the RKE transmitter is pressed, or the vehicle is no longer off. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-62 CHIME VOLUME This feature allows you to select the volume level of the chime. Press the vehicle information button until CHIME VOLUME appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: NORMAL: The chime volume will be set to a normal level. LOUD: The chime volume will be set to a loud level. NO CHANGE: No change will be made to this feature. The current setting will remain. There is no default for chime volume. The volume will stay at the last known setting. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. REMOTE START If your vehicle has this feature, it allows you to turn the remote start off or on. The remote start feature allows you to start the engine from outside of the vehicle using the RKE transmitter. See Remote Vehicle Start on page 2-8 for more information. Press the vehicle information button until REMOTE START appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: OFF: The remote start feature will be disabled. ON (default): The remote start feature will be enabled. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. FACTORY SETTNGS (Settings) This feature allows you to set all of the personalization features back to their factory default settings. Press the vehicle information button until FACTORY SETTNGS (Settings) appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the vehicle information button to scroll through the following settings: RESTORE ALL (default): The personalization features will be set to their factory default settings. DO NOT RESTORE: The personalization features will not be set to their factory default settings. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. 3-63 FEATURE SETTNGS (Settings): PRESS V TO EXIT This feature allows you to exit the feature settings menu. Press the vehicle information button until FEATURE SETTNGS (Settings): PRESS V TO EXIT appears in the DIC display. Press the set/reset button to exit the menu. If you do not exit, pressing the vehicle information button again will return you to the beginning of the vehicle information menu. Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs: The vehicle is shifted out of PARK (P). The vehicle is no longer in ON/RUN. The trip/fuel DIC button is pressed. The end of the feature settings menu is reached and exited. (cid:127) A 40 second time period has elapsed with no selection made. Audio System(s) Determine which radio your vehicle has and then read the pages following to familiarize yourself with its features. {CAUTION: This system provides you with far greater access to audio stations and song listings. Giving extended attention to entertainment tasks while driving can cause a crash and you or others can be injured or killed. Always keep your eyes on the road and your mind on the drive — avoid engaging in extended searching while driving. Keeping your mind on the drive is important for safe driving. See Defensive Driving on page 4-2. Here are some ways in which you can help avoid distraction while driving. 3-64 (cid:127) (cid:127) (cid:127) (cid:127) While your vehicle is parked: Familiarize yourself with all of its controls. Familiarize yourself with its operation. (cid:127) Set up your audio system by presetting your favorite radio stations, setting the tone, and adjusting the speakers. Then, when driving conditions permit, you can tune to your favorite radio stations using the presets and steering wheel controls if the vehicle has them. Notice: Before adding any sound equipment to your vehicle, such as an audio system, CD player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer/retailer. Also, check federal rules covering mobile radio and telephone units. If sound equipment can be added, it is very important to do it properly. Added sound equipment may interfere with the operation of your vehicle’s engine, radio, or other systems, and even damage them. Your vehicle’s systems may interfere with the operation of sound equipment that has been added. Your vehicle has a feature called Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 2-21 for more information. Setting the Time Without Date Display AM/FM Base Radio with a Single CD Player This type of radio has a H (clock) button for setting the time. Set the time by following these steps: 1. Turn the radio on. 2. Press the H button until the hour begins ﬂashing on the display. Press the H button a second time and the minutes begin ﬂashing on the display. 3. While either the hour or the minutes are ﬂashing, turn the f (tune) knob, located on the upper right side of the radio, clockwise or counterclockwise to increase or decrease the time. Instead of using the f knob, you can also press the SEEK arrows, \FWD (forward), or sREV (reverse) buttons to adjust the time. 4. Press the H button again until the clock display stops ﬂashing to set the currently displayed time; otherwise, the ﬂashing stops after ﬁve seconds and the current time displayed is automatically set. 3-65 (cid:127) (cid:127) With Date Display Single CD (MP3) or a Single CD and DVD (MP3) Player These radios have a H (clock) button for setting the time and date. To set the time and date, follow these instructions: 1. Turn the radio on. 2. Press the H button and the HR, MIN, MM,

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2008 Chevrolet Equinox Owners Manual

We're sorry....

A temporary error occurred while processing your request.

Please wait a moment and refresh this page by clicking here.

Thank you for your patience.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2008 Chevrolet Equinox Owners Manual

We're sorry.... A temporary error occurred while processing your request. Please wait a moment and refresh this page by clicking here. Thank you for your patience.

We're sorry....

A temporary error occurred while processing your request.

Please wait a moment and refresh this page by clicking here.

Thank you for your patience.