Download PDF Manual

The parking brake lever is located to the right of the driver’s seat. To set the parking brake, hold the brake pedal down and pull up on the parking brake lever. If the ignition is on, the brake system warning light will come on.


2-31


To release the parking brake, hold the brake pedal down. Pull the parking brake lever up until you can press the release button. Hold the release button in as you move the brake lever all the way down. Make sure to release the parking brake before driving the vehicle. If the parking brake is applied and the vehicle is moving at least 4 mph (6 km/h), a chime will activate to remind you to release the parking brake. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving.


2-32


Shifting Into PARK (P)


{CAUTION:


It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-33.


1. Hold the brake pedal down with your foot and set


the parking brake. See Parking Brake on page 2-31
for more information.


2. Move the shift lever into PARK (P) by pressing the


button on the shift lever and pushing the lever all the way toward the front of the vehicle.


3. Turn the ignition key to LOCK/OFF. 4. Remove the key and take it with you. If you can


leave your vehicle with the key, your vehicle is in PARK (P).


Torque Lock If you are parking on a hill and you do not shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To find out how, see Shifting Into PARK (P) on page 2-32. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of PARK (P).


Leaving Your Vehicle With the Engine Running


{CAUTION:


It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Do not leave your vehicle with the engine running.


If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is firmly set before you leave it. After you have moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without first pressing the button on the console shift lever. If you can, it means that the shift lever was not fully locked into PARK (P).


2-33


If you still are unable to shift out of PARK (P): 1. Fully release the shift lever button. 2. While holding down the brake pedal, press the


shift lever button again.


3. Move the shift lever to the desired position. If you still cannot move the shift lever from PARK (P), consult your dealer/retailer or a professional towing service.


Parking Over Things That Burn


{CAUTION:


Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn.


Shifting Out of PARK (P) This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: (cid:127) Prevent ignition key removal unless the shift


lever is in PARK (P) with the shift lever button fully released, and


(cid:127) Prevent movement of the shift lever out of PARK (P), unless the ignition is in ON/RUN or ACC/ACCESSORY and the regular brake pedal is applied.


The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9 volt) battery. If your vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 5-36 for more information. To shift out of PARK (P) use the following: 1. Apply the brake pedal. 2. Then press the shift lever button. 3. Move the shift lever to the desired position.


2-34


Engine Exhaust


{CAUTION:


Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if:


(cid:127) The exhaust system sounds strange


or different.


(cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision.


CAUTION:


(Continued)


(cid:127) Your vehicle was damaged when driving


over high points on the road or over road debris.


(cid:127) Repairs were not done correctly. (cid:127) Your vehicle or the exhaust system


has been modified improperly.


If you ever suspect exhaust is coming into your vehicle:


(cid:127) Drive it only with all the windows down


to blow out any CO; and


(cid:127) Have your vehicle fixed immediately.


CAUTION:


(Continued)


2-35


Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know.


{CAUTION:


{CAUTION:


Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-35. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-17.


It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to PARK (P).


Follow the proper steps to be sure your vehicle will not move. See Shifting Into PARK (P) on page 2-32. If you are parking on a hill and if you are pulling a trailer, also see Towing a Trailer on page 4-33.


2-36


Mirrors


Manual Rearview Mirror When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from the lamps behind you. Push the tab forward for daytime use and pull it for nighttime use.


Manual Rearview Mirror with OnStar® To adjust the angle of the mirror, move the mirror to a position that allows you see to out of the back window. To adjust the height of the mirror, adjust the arm that connects the mirror to the windshield. To reduce glare from lights behind you, move the lever toward you to the night position. There are also OnStar® buttons located at the bottom of the mirror face. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-39 for more information about the services OnStar® provides.


Automatic Dimming Rearview Mirror with OnStar® The vehicle may have an automatic dimming inside rearview mirror with OnStar® controls. For more information about OnStar®, see OnStar® System on page 2-39. O(On/Off): The on/off button, located on the lower left side of the mirror, is used for the automatic dimming functions of the rearview mirror. Mirror Operation The automatic dimming feature comes on each time the vehicle is started. Automatic dimming reduces the glare of lights from behind the vehicle. To turn the automatic dimming feature on or off, press and release the AUTO/ ((off) button. The indicator light will come on when this feature is on.


2-37


Outside Convex Mirrors The passenger’s side mirror is convex. A convex mirror’s surface is curved, creating a wider area of vision for the driver.


{CAUTION:


A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes.


Outside Power Mirrors


The controls for the power mirrors are located on the instrument panel.


To adjust the mirrors, do the following:


1. Move the selector switch to the left or right to


choose the driver’s or passenger’s mirror.


2. Press the corresponding edges of the round control


pad to move each mirror to the desired direction. Adjust each outside mirror so that you can see a little of your vehicle, and the area behind your vehicle.


2-38


OnStar® System


OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar button and they can contact Roadside Service for you. OnStar service is provided to you subject to the OnStar Terms and Conditions. You may cancel your OnStar service at any time by contacting OnStar.


A complete OnStar Owner’s Guide and the OnStar Terms and Conditions are included in the vehicle’s OnStar Subscriber glove box literature. For more information, visit onstar.com or onstar.ca, contact OnStar at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar button to speak with an OnStar advisor 24 hours a day, 7 days a week. Not all OnStar features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar services and system limitations, see the OnStar Owner’s Guide in your glove box or visit onstar.com. OnStar Services For new vehicles with OnStar, the Safe & Sound Plan, or the Directions & Connections Plan is included for one year from the date of purchase. You can extend this plan beyond the first year, or upgrade to the Directions & Connections Plan. For more information, press the OnStar button to speak with an advisor. Some OnStar services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar.


2-39


Available Services with Safe & Sound Plan (cid:127) Automatic Notification of Airbag Deployment (cid:127) Advanced Automatic Crash Notification (AACN)


(If equipped) Link to Emergency Services


(cid:127) Roadside Assistance (cid:127) Stolen Vehicle Location Assistance (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) OnStar Vehicle Diagnostics (cid:127) GM Goodwrench® On Demand Diagnostics (cid:127) OnStar Hands-Free Calling with


30 complimentary minutes


(cid:127) OnStar Virtual Advisor (U.S. Only) Available Services included with Directions & Connections Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions - Advisor delivered or OnStar


Turn-by-Turn Navigation (If equipped)


(cid:127) RideAssist


Information and Convenience Services


2-40


OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To find out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar Owner’s Guide for more information (Only available in the continental U.S.).


(cid:127) (cid:127) OnStar Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-108 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” to activate the OnStar Hands-Free Calling. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar Owner’s Guide for more information.


How OnStar Service Works Your vehicle’s OnStar system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar Call Center at the time of an OnStar button press, Emergency button press or if your airbags or AACN system deploys.


The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar Hands-Free Calling, your vehicle also sends OnStar your GPS location so that we can provide you with location-based services. OnStar service cannot work unless your vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless you are in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. Location information about your vehicle is only available if the GPS satellite signals are unobstructed and available.


2-41


Your vehicle must have a working electrical system (including adequate battery power) for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility Increase the radio volume if you cannot hear the OnStar advisor. If the light next to the OnStar buttons is red, this means that your system is not functioning properly and should be checked by your dealer/retailer. If the light appears clear (no light is appearing), your OnStar subscription has expired. You can always press the OnStar button to confirm that your OnStar equipment is active.


Storage Areas


Glove Box To open the glove box, pull the handle to the left and pull the glove box door down until it stops and is fully open.


Cupholder(s) There are two cupholders located at the lower front of the center console armrest and a molded cupholder on the floor of the center console. To use the cupholders on the armrest, pull the tray forward. There are two cupholders located at the rear of the center console. Pull downward on the lid to use the cupholders.


Center Console Storage Your vehicle may have a center console armrest with storage area. Use the lever on the front of the console to open it.


2-42


Luggage Carrier


{CAUTION:


If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along. This can cause you to lose control. What you are carrying could be violently torn off, and this could cause you or other drivers to have a collision, and of course damage your vehicle. You may be able to carry something like this inside. But, never carry something longer or wider than the luggage carrier on top of your vehicle.


Your vehicle may have a luggage carrier that allows you to load things on top of your vehicle. The luggage carrier has side rails attached to the roof, sliding crossrails, if equipped, and places to use for tying things down. These let you load some things on top of your vehicle, as long as they are not wider or longer than the luggage carrier.


The roof rack crossrails can be locked in four positions only.


2-43


Press the lever down and align the crossrails on both sides with the holes on the siderails. Move the crossrail by hand. There will be a notable click as the pins align into the holes locking the crossrail into place. Make sure the lever is in the down position, and that you are not able to slide the crossrail with your hand when it is in place.


To reposition the crossrail, pull up on the end levers of the crossrail to the upright position. This releases the pins from the holes in the siderail and lets you move the crossrail into a new position. Notice: Loading cargo on the luggage carrier that weighs more than 220 lbs (100 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely. Do not stand on plastic lower body panels when loading cargo on the luggage carrier.


2-44


Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-22. To prevent damage or loss of cargo as you are driving, check now and then to make sure the luggage carrier crossrails are locked and cargo is still securely fastened. When the luggage carrier is not in use, lock one crossrail at the rear most position on the siderails and lock the other crossrail above the opening of the rear door to reduce wind noise.


Rear Compartment Storage Panel/Cover Your vehicle may have an adjustable panel/cargo cover feature. The panel/cargo cover can be adjusted into three positions.


There may also be a flip panel towards the front of the cargo cover. You may have to move this panel upward in order to gain access to the cargo cover.


2-45


The panel can be used in this position if you need additional space above the panel. Place the cargo on top of the panel in this position.


{CAUTION:


If you were to carry things on the adjustable panel when it is in the upper (cargo cover) or center positions, during a sudden vehicle movement or a crash, those things could be thrown around in the vehicle. You or others could be injured. When it is in the upper or center position, always secure any cargo on the floor beneath the panel/cover.


To use the panel in the lower position, do the following: 1. Insert the front corners of the panel into the


lower guides.


2. Slide the panel forward. 3. Press down on the back of the panel to lock


it in place.


2-46


To use the panel in the center position, do the following: 1. Insert the front corners of the panel into the


middle guides.


2. Slide the panel forward. 3. Press down and pull rearward on the back


of the panel to lock it in place.


The panel can be used in this position when you have to place a flat or spare tire in the rear cargo area.


To use the panel in the upper position, do the following: 1. Insert the front corners of the panel into the


top guides.


2. Slide the panel forward. 3. Press down and pull rearward on the back


of the panel to lock it in place.


This can be used as a cargo cover for the rear area. The panel may be installed either carpet or plastic side up. The panel may also be used as a table in this position. See Table on page 2-48 for more information.


Rear Seat Armrest Your vehicle may have a rear seat armrest that contains two cupholders. To access the cupholders, pull the armrest down from the rear seatback.


2-47


To set up the table, do the following: 1. With the adjustable panel in the upper position


pull rearward to position it for use as a table. The plastic side should be up.


2. Turn the knob to release the leg from the plastic


side of the table and turn the leg outward.


3. Set the table leg onto the liftgate lock striker at


the rear edge of the vehicle.


Make sure to place the table leg securely onto the liftgate lock striker. Notice: Driving with the panel extended into the table position could damage your vehicle. Always have the panel in the stored position while you are driving. Notice: Placing hot items on the surface of the table could damage it. Always be sure that the items that are placed on the surface of the table are of moderate temperature. There are four hooks located on the table that can be used for grocery bags.


Table


Your vehicle may have an adjustable panel/cargo cover that also functions as a table. The maximum load for the table is 100 lbs. distributed (45 kg).


2-48


Convenience Net Your vehicle may have a convenience net in the rear of the vehicle. Store small loads as far forward as possible. The net should not be used to store heavy loads.


Cargo Tie Downs Cargo tie-downs located in the rear of the vehicle are used to secure small loads. Sunroof If the vehicle is equipped with a sunroof, the controls to operate it are located on the headliner above the rearview mirror. The ignition must be in RUN or ACC, or Retained Accessory Power (RAP) must be active, to operate the sunroof. See Retained Accessory Power (RAP) on page 2-21 for more information.


To express-open the sunroof glass panel and sunshade, press the switch rearward and release it.


To stop the sunroof before it is completely open, press the switch rearward again. The sunshade cannot be closed with the sunroof open. To close the sunroof, press forward and hold the switch until the sunroof stops, lifts and seals at the back of the sunroof glass. Press forward on the switch again, to make sure the sunroof is fully closed To put the sunroof in the vent position, pull down on the front of the switch. Push up on the front of the switch to close it.


2-49


✍ NOTES


2-50


Section 3


Instrument Panel


Instrument Panel Overview ...............................3-4
Hazard Warning Flashers ................................3-6
Other Warning Devices ...................................3-6
Horn .............................................................3-6
Tilt Wheel .....................................................3-6
Turn Signal/Multifunction Lever .........................3-7
Turn and Lane-Change Signals ........................3-8
Headlamp High/Low-Beam Changer ..................3-8
Flash-to-Pass .................................................3-8
Windshield Wipers ..........................................3-9
Windshield Washer .......................................3-10
Rear Window Wiper/Washer ...........................3-10
Cruise Control ..............................................3-10
Headlamps ..................................................3-13
Headlamps on Reminder ................................3-13
Daytime Running Lamps (DRL) .......................3-14
Automatic Headlamp System ..........................3-14
Fog Lamps ..................................................3-15
Instrument Panel Brightness ...........................3-15
Dome Lamp .................................................3-16
Entry Lighting ...............................................3-16
Map Lamps .................................................3-16
Cargo Lamp .................................................3-16
Electric Power Management ...........................3-17
Battery Run-Down Protection ..........................3-17
Accessory Power Outlet(s) .............................3-18


Ashtray(s) and Cigarette Lighter ......................3-18
Climate Controls ............................................3-19
Climate Control System .................................3-19
Outlet Adjustment .........................................3-22
Passenger Compartment Air Filter ...................3-22
Warning Lights, Gages, and Indicators ............3-24
Instrument Panel Cluster ................................3-25
Speedometer and Odometer ...........................3-26
Trip Odometer ..............................................3-26
Tachometer .................................................3-26
Safety Belt Reminders ...................................3-27
Airbag Readiness Light ..................................3-27
Passenger Airbag Status Indicator ...................3-28
Charging System Light ..................................3-30
Brake System Warning Light ..........................3-31
Antilock Brake System Warning Light ...............3-32
Traction Control System (TCS) Warning Light ...3-32
Engine Coolant Temperature Warning Light ......3-33
Engine Coolant Temperature Gage ..................3-33
Tire Pressure Light .......................................3-34
Malfunction Indicator Lamp .............................3-34
Oil Pressure Light .........................................3-37
Change Engine Oil Light ................................3-38
Security Light ...............................................3-38
Fog Lamp Light ............................................3-38
Cruise Control Light ......................................3-38


3-1


Section 3


Instrument Panel


Audio System(s) .............................................3-64
Setting the Time ...........................................3-65
Radio(s) ......................................................3-68
Using an MP3 (Radio with CD


or Six-Disc CD Player) ...............................3-87


Using an MP3 (Radio with CD


and DVD Player) .......................................3-92
XM Radio Messages .....................................3-97
Navigation/Radio System ...............................3-98
Rear Seat Entertainment (RSE) System ...........3-99
Theft-Deterrent Feature ................................3-108
Audio Steering Wheel Controls ......................3-108
Radio Reception .........................................3-110
Multi-Band Antenna .....................................3-110


Reduced Engine Power Light .........................3-39
Highbeam On Light .......................................3-39
Service All-Wheel Drive Light .........................3-39
All-Wheel Drive Disabled Light ........................3-40
Gate Ajar Light .............................................3-40
Door Ajar Light .............................................3-40
Service Vehicle Soon Light ............................3-41
Fuel Gage ...................................................3-41
Low Fuel Warning Light .................................3-42
Driver Information Center (DIC) .......................3-42
DIC Operation and Displays ...........................3-43
DIC Compass ..............................................3-46
DIC Warnings and Messages .........................3-49
DIC Vehicle Personalization ............................3-58


3-2


✍ NOTES


3-3


Instrument Panel Overview


3-4


The main components of your instrument panel are the following:


A. Air Outlets. See Outlet Adjustment on page 3-22. B. Turn Signal/Multifunction Lever. See Turn


Signal/Multifunction Lever on page 3-7.


C. Instrument Panel Cluster. See Instrument Panel


Cluster on page 3-25.


D. Windshield Wiper/Washer Lever. See Windshield


Wipers on page 3-9.


E. Driver Information Center Controls. See DIC


Operation and Displays on page 3-43.


F. Hazard Warning Flashers. See Hazard Warning


Flashers on page 3-6.


G. Passenger Airbag Status Indicator. See Passenger


Airbag Status Indicator on page 3-28.


H. Rear Window Wiper/Washer Buttons. See Rear


Window Wiper/Washer on page 3-10. Fog Lamps Button. See Fog Lamps on page 3-15.


I. Power Mirror Control. See Outside Power Mirrors


on page 2-38.


J. Instrument Panel Brightness Control. See


Instrument Panel Brightness on page 3-15.


K. Cruise Controls. See Cruise Control on page 3-10. L. Tilt Wheel. See Tilt Wheel on page 3-6. M. Horn. See Horn on page 3-6. N. Audio Steering Wheel Controls. See Audio


Steering Wheel Controls on page 3-108.


O. Audio System. See Audio System(s) on page 3-64. P. Shift Lever. See Shifting Into PARK (P)


on page 2-32.


Q. Traction Control System (TCS) Button. See Traction Control System (TCS) on page 4-6.


R. Power Window Switches. See Power Windows


on page 2-16.


S. Climate Control System. See Climate Control System on page 3-19. Heated Seat Buttons (If Equipped). See Heated Seats on page 1-4.


T. Glove Box. See Glove Box on page 2-42.


3-5


Hazard Warning Flashers The hazard warning flashers let you warn the police and others that you have a problem. The front and rear turn signal lamps will flash on and off.


Other Warning Devices If you carry reflective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle.


The hazard warning flasher button is located towards the center of the instrument panel.


Horn Press near or on the horn symbols on the steering wheel pad to sound the horn.


Tilt Wheel Your vehicle has a tilt wheel that allows you to adjust the steering wheel.


Press the button to make the front and rear turn signal lamps flash on and off. Press the button again to turn the flashers off. While the hazard warning flashers are on, the turn signals do not work. The hazard warning flashers work no matter what position the key is in, and even if the key is not in the ignition switch.


3-6


Turn Signal/Multifunction Lever


The lever to tilt the steering wheel is located on the left side of the steering column. To tilt the wheel, hold the steering wheel and push the lever down. Then, move the steering wheel to a comfortable position and pull the lever up firmly to lock the column in place.


The lever on the left side of the steering column includes the following: (cid:127) GTurn and Lane-Change Signals.


See Turn and Lane-Change Signals on page 3-8.


(cid:127) 53Headlamp High/Low-Beam Changer.


See Headlamp High/Low-Beam Changer on page 3-8. Flash-to-Pass. See Flash-to-Pass on page 3-8.


(cid:127) OExterior Lamp Control. See Headlamps


on page 3-13.


3-7


(cid:127) Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.


Headlamp High/Low-Beam Changer To change the headlamps from low beam to high, push the turn signal lever away from you. To change from high beam to low beam, pull the turn signal lever towards you. To flash the high beams from low beam, pull the turn signal lever all the way towards you. Then release it.


An arrow on the instrument panel cluster will flash in the direction of the turn or lane change.


When the high beams are on, this light on the instrument panel cluster will also be on.


To signal a lane change, raise or lower the lever until the arrow starts to flash. Hold it there until you complete the lane change. The lever will return by itself when you release it. As you signal a turn or a lane change, if the arrows flash rapidly, a signal bulb may be burned out and other drivers won’t see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check the fuse, see Fuses and Circuit Breakers on page 5-100 and for burned-out bulbs.


3-8


Flash-to-Pass This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. To flash the high beams from low beam, pull the turn signal/multifunction lever all the way towards you. Then release it.


Windshield Wipers Be sure to clear ice and snow from the wiper blades before using them. If the wiper blades are frozen to the windshield, gently loosen or thaw them. If the blades do become damaged, install new blades or blade inserts. See Windshield Wiper Blade Replacement on page 5-50. Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Clear away snow or ice to prevent an overload.


& (Delay): Move the lever to this position to set a delay between wipes.


6 (Delay Adjustment): Move the lever to the delay position to choose a delayed wiping cycle. Turn the intermittent adjust band down for a longer delay or up for a shorter delay. 9(Off): Move the lever to this position to turn off the windshield wipers. 8(Mist): Move the lever all the way down to mist and release for a single wiping cycle. The windshield wipers will stop after one wipe and the lever returns to its parked position. If more wipes are needed, hold the lever on mist longer.


Use the lever on the right side of the steering column to operate the windshield wipers. 1 (High Speed): Move the lever to this position for steady wiping at high speed. 6 (Low Speed): Move the lever to this position for steady wiping at low speed.


3-9


Windshield Washer


{CAUTION:


In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.


There is a button marked with the windshield washer symbol at the end of the windshield wiper lever. Press this button to spray washer fluid on the windshield. The wipers will run for a few cycles to clear the window and then either stop or return to your preset speed. For more wash cycles, press and hold the button longer.


Rear Window Wiper/Washer The rear wiper and rear wash buttons are located on the instrument panel above the audio system.


Z (Rear Wiper): Press this button to turn the rear wiper on and off. When the wiper is on it will run continuously at a preset speed.


Y (Wash): Press this button to spray washer fluid on the rear window. The window wiper will also come on. Release the button when enough fluid has been sprayed on the window. The rear wiper will run a few more cycles after it is released. If the rear wiper function was already on, prior to pressing the wash button, it will stay on until the wiper button is pressed again. The rear window washer uses the same fluid that is in the windshield washer reservoir. See Windshield Washer Fluid on page 5-32.


Cruise Control Cruise control lets you maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below 25 mph (40 km/h).


3-10


{CAUTION:


Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.


{CAUTION:


If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.


The cruise control buttons are located on the steering wheel.


J(On/Off): Press this button to turn the cruise control system on and off. The indicator light is on when cruise control is on and turns off when cruise control is off.


+RES (Resume): Press this button to resume a set speed and to accelerate the speed. SET− (Set): Press this button to set a speed and to decrease the speed.


[ (Cancel): Press this button to cancel cruise control without erasing the set speed from memory.


3-11


Setting Cruise Control The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed. 1. Press the on/off button to turn cruise control on. 2. Get up to the desired speed. 3. Press the SET− button and release it. 4. Take your foot off the accelerator pedal. When the brakes are applied, the cruise control shuts off. If the vehicle is in cruise control and the Traction Control System (TCS) begins to limit wheel spin, the cruise control automatically disengages. See Traction Control System (TCS) on page 4-6. When road conditions allow, the cruise control can be used again. Resuming a Set Speed If the cruise control is at the set speed desired and the brakes are applied, the cruise control shuts off. The cruise symbol in the instrument panel cluster also goes off indicating cruise is no longer engaged. To return to your previously set speed, you do not need to go through the set process again. Once you are driving about 25 mph (40 km/h) or more, press the +RES button on your steering wheel. The vehicle goes back to the previous set speed and stays there.


3-12


Increasing Speed While Using Cruise Control There are two ways to go to a higher speed. (cid:127) Press and hold the +RES button on the steering


wheel until the desired speed is reached, then release it. To increase vehicle speed in small amounts, press the +RES button. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) faster.


Reducing Speed While Using Cruise Control To reduce your speed while using cruise control: (cid:127) Press and hold the SET– button on the steering wheel until the desired lower speed is reached, then release it. To slow down in very small amounts, push the SET− button on the steering wheel briefly. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) slower.


Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle’s speed. When you take your foot off the pedal, the vehicle slows down to the cruise control speed that was set earlier.


(cid:127) (cid:127) Using Cruise Control on Hills How well your cruise control works on hills depends upon the vehicle’s speed, load, and the steepness of the hills. While going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed. While going downhill, you might have to brake or shift to a lower gear to keep the vehicle at a lower speed. However, when the brakes are applied the cruise control turns off. Many drivers find this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are three ways to end cruise control: (cid:127) Step lightly on the brake pedal. (cid:127) Press the [ button on the steering wheel. (cid:127) Press the J button on the steering wheel. Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off. Headlamps The exterior lamp control is located on the turn signal/multifunction lever. O(Exterior Lamp Control): Turn the control with this symbol on it to operate the exterior lamps.


The exterior lamp control has the following positions: AUTO (Off/Automatic Headlamps): Turn the control to this position to put the headlamps in automatic mode. Automatic mode will turn the exterior lamps on and off depending upon how much light is available outside of the vehicle. ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: (cid:127) Sidemarker Lamps


Taillamps License Plate Lamps Instrument Panel Lights


53(Headlamps): Turning the control to this position turns on the headlamps, together with the previously listed lamps and lights.


Headlamps on Reminder If you open the driver’s door with the ignition off and the lamps on, you will hear a warning chime.


3-13


(cid:127) (cid:127) (cid:127) When the headlamps are turned off, the regular lamps will go off, and the low-beam headlamps come on to the reduced brightness. To idle your vehicle with the DRL off, move the shift lever to PARK (P). The DRL will stay off until the shift lever is moved out of the PARK (P) position. The regular headlamp system should be turned on when needed.


Automatic Headlamp System When it is dark enough outside and the exterior lamps control is in the automatic position, the headlamps will come on automatically. See Headlamps on page 3-13. Your vehicle has a light sensor located on top of the instrument panel. Make sure it is not covered, or the headlamps will be on when you do not need them. The system may also turn on the headlamps when driving through a parking garage or tunnel.


Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional Daytime Running Lamps (DRL) are required on all vehicles first sold in Canada. The DRL system will make your low-beam headlamps come on at a reduced brightness in daylight when the following conditions are met:


The ignition is on. The exterior lamp band is in the automatic position. The transmission is not in PARK (P). The light sensor determines it is daytime. The parking brake is released.


When the DRL are on, the low-beam headlamps will be on at a reduced brightness. The taillamps, sidemarker and other lamps will not be on. The instrument panel will not be lit up either. When the exterior lamp band is turned to the headlamp position, the low-beam headlamps come on. The other lamps that come on with the headlamps will also come on.


3-14


(cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Fog Lamps If your vehicle has this feature, use the fog lamps for better visibility in foggy or misty conditions.


Instrument Panel Brightness This feature controls the brightness of the instrument panel lights.


The fog lamps button is located on the instrument panel above the radio.


The control for this feature is located on the instrument panel to the left of the steering column.


To use the fog lamps, the parking lamps or low-beam headlamps must be on. Push the button to turn the fog lamps on or off. The fog lamp button is lit when the lamps are on. The fog lamps will go off whenever the high-beam headlamps are turned on. When the high-beam headlamps are turned off, the fog lamps will come on again. Some localities have laws that require the headlamps to be on along with the fog lamps.


Turn the control up to brighten the lights or down to dim them.


3-15


Dome Lamp If the vehicle has a dome lamp with a switch, the following are the settings. 9(Off): Move the lever to this position to turn the lamp off, even when a door is open.


1(Door): Move the lever to this position so that the lamp comes on when a door is opened.


+(On): Move the lever to this position to turn the dome lamp on.


Entry Lighting The dome lamp and the cargo lamp inside the vehicle comes on when any door is opened, if the dome lamp is in the door position. In addition, these lamps come on when the Remote Keyless Entry (RKE) unlock button is pressed. It stays on for 20 seconds or until a door is opened. After the door is opened and then closed, the light remains on for 20 seconds, or until the key is put in the ignition and turned to the ON/RUN position.


3-16


Map Lamps


Your vehicle may have lamps located on the headliner above the rearview mirror. Push on the lens in the lamp to turn them on and off.


Cargo Lamp The cargo lamp is located over the rear compartment, and is controlled by the dome lamp. See Dome Lamp on page 3-16.


Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle


speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as Battery Saver Active or Service Battery Charging System. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 3-49.


Battery Run-Down Protection Your vehicle has a battery saver feature designed to protect the vehicle’s battery. When any interior lamp is left on and the ignition is turned off, the battery rundown protection system will automatically turn the lamp off after 20 minutes. This will avoid draining the battery. This vehicle also has a retained accessory power feature. If the radio is on, it will turn off after 10 minutes or if any door on the vehicle is opened. See Retained Accessory Power (RAP) on page 2-21.


3-17


If electrical devices are left plugged into a


Accessory Power Outlet(s) The accessory power outlets can be used to connect electrical equipment such as a cellular phone or CB radio. The two accessory power outlets are located in the front and at the rear of the center console storage area. To use the outlets, remove the cover. When not in use, always cover the outlet with the protective cap. Notice: power outlet, the battery may drain causing your vehicle not to start or damage to the battery. This would not be covered by the warranty. Always unplug all electrical devices when turning off your vehicle. Certain electrical accessories may not be compatible with the accessory power outlets and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on the accessory power outlet. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment.


3-18


When adding electrical equipment, be sure to follow the installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only.


Ashtray(s) and Cigarette Lighter Your vehicle may have a removable ashtray and cigarette lighter. The ashtray can be placed into the front console cupholders. To use the lighter, push it in all the way and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Do not use equipment exceeding maximum amperage rating of 15 amperes. Notice: If you put papers, pins, or other flammable items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put flammable items in the ashtray.


Climate Controls


Climate Control System The heating, cooling, and ventilation for the vehicle can be controlled with this system. If your vehicle has the remote start feature, the climate control system functions as part of the remote start feature. See Remote Keyless Entry (RKE) System Operation on page 2-5.


Operation 9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. In any setting other than off, the fan runs continuously with the ignition on. To turn off the air completely, turn the fan to 0 and select the recirculation button.


Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the temperature inside the vehicle. Use the right knob to select from the following modes: There is one position between each mode to finely adjust airflow position. H(Vent): This mode directs air to the instrument panel outlets. )(Bi-Level): This mode splits the air between the instrument panel outlets and the floor outlets. 6(Floor): This mode directs most of the air to the floor outlets with some air directed to the windshield and side windows. The right knob may also be used to select the defrost and defog modes that are described in this section. You can also select modes by using the following buttons: ; (Outside Air): Press this button to turn the outside air mode on. When this mode is on, outside air will circulate throughout the vehicle. When the button is pressed, an indicator light in the button comes on to show that it is activated. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode.


3-19


@ (Recirculation): Press this button to recirculate cabin air through the vehicle. It can be used to prevent outside air and odors from entering the vehicle or to help heat or cool the air inside the vehicle more quickly. An indicator light will come on in this mode. Operation in this mode during periods of high humidity and cool outside temperatures may result in increased window fogging. If window fogging is experienced, select the defrost mode.


The recirculation mode cannot be used with floor, defrost, or defogging modes. If you try to select recirculation in one of those modes, the indicator light flashes several times and turns off. #(Air Conditioning): Press this button to turn the air conditioning system on or off. When this button is pressed, an indicator light on the button comes on to show that the air conditioning is activated. The air conditioning can be selected in any mode as long as the fan switch is on. The air conditioning compressor does not operate when outside temperatures fall below 38°F (3°C). The indicator light flashes several times and turns off when outside conditions affect air conditioning operation. This is normal.


On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for the vehicle to cool down. It also helps the system to operate more efficiently. For quick cool down on hot days, select the following settings together: 1. Vent mode. 2. Outside air. 3. Air conditioning. 4. The coolest temperature. 5. The highest fan speed. 6. Once the vehicle’s interior temperature is below the


outside temperature, select recirculation mode for enhanced cooling.


Using these settings together for long periods of time may cause the air inside of the vehicle to become too dry. To prevent this from happening, after the air inside of the vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so a small amount of water might drip underneath the vehicle while idling or after turning off the engine. This is normal. ( (Heated Seats): If your vehicle has heated seats, see Heated Seats on page 1-4.


3-20


Defogging and Defrosting Fog or frost on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. When either of these modes are selected, the system runs the air conditioning compressor and cancels the recirculation mode to dry the air. For best results, clear all snow and ice from the windshield before defrosting. Turn the right knob to select the defog or defrost mode. -(Defog): This mode directs half of the air to the windshield and the side window outlets, and half to the floor outlets. 0(Defrost): This mode directs most of the air to the windshield and the side window outlets, with some air directed to the floor outlets.


Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. The rear window defogger only works when the ignition is in ON/RUN. <(Rear): Press this button to turn the rear window defogger on or off. An indicator light on the button comes on to show that the rear window defogger is activated. The rear window defroster stays on for about 10
minutes if the vehicle remains at slower vehicle speeds or until the button is pressed, or unless the ignition is turned to ACC/ACCESSORY or LOCK/OFF. If turned on again, the defogger only runs for about five minutes before turning off again. At higher vehicle speeds, the defogger may stay on continuously. The defogger can always be turned off by pressing the button again or by turning off the ignition.


3-21


If your vehicle has the remote start feature, the rear defogger automatically turns on if it is cold outside. When the vehicle transitions out of the remote start mode, the rear defogger will turn off. See Remote Keyless Entry (RKE) System Operation on page 2-5. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid.


Remote Start Climate Control Operation If your vehicle has the remote start feature and it is activated, the climate control system heats and cools the inside of the vehicle using the modes that were set before the vehicle was turned off and the rear defogger automatically turns on. If your vehicle has heated seats, they may turn on if it is cold outside and will shut off when the key is turned to ON/RUN. See Heated Seats on page 1-4.


3-22


Outlet Adjustment Use the louvers located on the air outlets to change the direction of the airflow. Operation Tips (cid:127) Clear away any ice, snow, or leaves from the air


inlets at the base of the vehicle that may block the flow of air into your vehicle.


(cid:127) Do not use any non-GM approved hood deflectors that could adversely affect the performance of the system.


(cid:127) Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively.


Passenger Compartment Air Filter Outside air is routed through a passenger compartment air filter before entering the vehicle. This filter removes certain particles from the air, including pollen and dust particles. Reductions in airflow, which may occur more quickly in dusty areas, indicate that the filter needs to be replaced early. The filter should be replaced as part of routine scheduled maintenance. See Scheduled Maintenance on page 6-4
for when to replace the filter.


To change the passenger compartment air filter, use the following steps:


1. The passenger’s side air inlet panel is located below


the center of the passenger’s side wiper blade. Remove the push pin retaining the air inlet panel. Pry the center of the push pin out 0.5 in (13 mm) for removal.


2. Open the hood. 3. Remove the three push pins from the top and


forward edge of the passenger’s side air inlet panel.


4. Remove the air inlet panel to access the filter. 5. Press the release tab on the driver’s side of the


filter and pull out the edge of the filter.


6. Remove the filter from the vehicle. 7. Install a new passenger compartment air filter.


For the type of filter to use see Maintenance Replacement Parts on page 6-14.


8. Reverse Steps 1 through 5.


3-23


Warning Lights, Gages, and Indicators This section describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the following pages, some warning lights come on briefly when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens.


Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there is a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly and even dangerous. So please get to know your warning lights and gages. They are a big help.


3-24


Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you are using, and many other things you will need to drive safely and economically.


United States version shown, Canada and Sport Model similar


3-25


Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper resistant odometer. The digital odometer will read 999,999 if someone tries to turn it back. You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set to the mileage total of the old odometer, then it must be. If not, then it is set at zero and a label must be put on the driver’s door to show the old mileage reading when the new odometer was installed.


Trip Odometer Your trip odometer is located in the Driver Information Center and shows how far your vehicle has been driven since the trip odometer was last reset. For more information see DIC Operation and Displays on page 3-43.


Tachometer The tachometer shows your engine speed in revolutions per minute (rpm). Notice: tachometer in the solid red area, your vehicle could be damaged. The damages would not be covered by your warranty. Do not operate the engine in the solid red area.


If you operate the engine with the


3-26


Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled.


The safety belt light will also come on and stay on for several seconds, then it will flash for several more.


This chime and light is repeated if the driver remains unbuckled and the vehicle is in motion. If the driver’s belt is already buckled, neither the chime nor the light will come on. Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-65 for more information. The passenger safety belt light, located on the instrument panel, will come on and stay on for several seconds and then flash for several more.


This chime and light are repeated if the passenger remains unbuckled and the vehicle is in motion.


If the passenger’s safety belt is buckled, neither the chime nor the light will come on. Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-56.


3-27


If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away.


Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your instrument panel has a passenger airbag status indicator.


{CAUTION:


If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inflate in a crash, or they could even inflate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle.


The airbag readiness light should flash for a few seconds when you start the engine. If the light does not come on then, have it fixed immediately. If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message may also come on. See DIC Warnings and Messages on page 3-49 for more information.


3-28


United States


Canada


When you start the vehicle, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal airbag.


If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag is enabled (may inflate).


{CAUTION:


{CAUTION:


If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. Do not use a rear-facing child restraint in the right front passenger’s seat if the airbag is turned on.


Even though the passenger sensing system is designed to turn off the right front passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be secured in the rear seat, even if the airbag is off.


If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag. See Passenger Sensing System on page 1-65
for more on this, including important safety information.


3-29


If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service.


{CAUTION:


If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the airbag(s). See Airbag Readiness Light on page 3-27 for more on this, including important safety information.


Charging System Light


If this light comes on while you are driving, you may have a problem with the charging system.


A charging system Driver Information Center (DIC) message may also appear. See DIC Warnings and Messages on page 3-49 for more information. This light could indicate that you have problems with a generator drive belt, or another electrical problem. Have it checked right away. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and air conditioner.


3-30


Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the brake system warning light comes on, there is a brake problem. Have your brake system inspected right away.


United States


Canada


The brake light is located in the instrument panel cluster. This light should come on briefly when you turn the ignition key to RUN. If it does not come on then, have it fixed so it will be ready to warn you if there is a problem.


When the ignition is on, the brake light will come on when you set your parking brake. The light will stay on if your parking brake does not release fully. A chime will also sound if the parking brake is not fully released and the vehicle is moving. If it stays on after your parking brake is fully released, it means you have a brake problem. The brake light will also come on to indicate a low brake fluid level. See Brakes on page 5-33 for more information. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push or the pedal may go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-28.


{CAUTION:


Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service.


3-31


Antilock Brake System Warning Light


Traction Control System (TCS) Warning Light


For vehicles with the Antilock Brake System (ABS), this light will come on briefly when you start the engine.


Your vehicle has a Traction Control System (TCS) and StabiliTrak® warning light.


That is normal. If the light does not come on then, have it fixed so it will be ready to warn you if there is a problem. If the ABS light stays on, turn the ignition off, if the light comes on when you are driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light still stays on, or comes on again while you are driving, your vehicle needs service. If the regular brake system warning light is not on, you still have brakes, but you do not have antilock brakes. If the regular brake system warning light is also on, you do not have antilock brakes and there is a problem with your regular brakes. See Brake System Warning Light on page 3-31
For vehicles with a Driver Information Center (DIC), see DIC Warnings and Messages on page 3-49 for all brake related DIC messages.


3-32


When the traction control is activated the light will flash when the TCS is limiting wheel spin or when the StabiliTrak® system is active. You may feel or hear the system working, but this is normal. This light may also come on after extended heavy braking indicating the brakes have become too hot to limit wheel spin. This light will come on and stay on if the TCS is turned off using the traction control on/off button, located next to the gear shift lever. If the TCS warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service. See Traction Control System (TCS) on page 4-6 and StabiliTrak® System on page 4-7 for more information.


Engine Coolant Temperature Warning Light


The engine coolant temperature warning light will come on when the engine has overheated.


Engine Coolant Temperature Gage


This gage measures the temperature of the vehicle’s engine.


If this happens you should pull over and turn off the engine as soon as possible. See Engine Overheating on page 5-24 for more information. Notice: Driving with the engine coolant temperature warning light on could cause your vehicle to overheat. See Engine Overheating on page 5-24. Your vehicle could be damaged, and it might not be covered by your warranty. Never drive with the engine coolant temperature warning light on.


If the indicator needle moves into the shaded area, the engine is too hot. A temperature indicator light will turn on. If you have been operating your vehicle under normal driving conditions, and the temperature indicator light comes on, you should pull off the road, stop your vehicle and turn off the engine as soon as possible.


3-33


Tire Pressure Light


This light comes on briefly when the engine is started.


This light will also come on when one or more of your tires are significantly underinflated. A tire pressure message in the Driver Information Center (DIC), may accompany the light. See DIC Warnings and Messages on page 3-49 for more information. Stop and check your tires as soon as it is safe to do so. If underinflated, inflate to the proper pressure. See Tires on page 5-52 for more information. If a problem is detected with the Tire Pressure Monitor System, this light will flash for approximately 60 seconds and then stay on solid for the remainder of the ignition cycle. See Tire Pressure Monitor System on page 5-62
for more information.


3-34


Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.


The check engine light comes on to indicate that there is an OBD II problem and service is required.


Malfunctions often are indicated by the system before any problem is apparent. This can prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. Notice: this light on, after a while, the emission controls might not work as well, your vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by your warranty.


If you keep driving your vehicle with


Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by your warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 5-3. This light comes on, as a check to show it is working, when the ignition is turned ON/RUN but the engine is not running. If the light does not come on, have it repaired. This light also comes on during a malfunction in one of two ways:


Light Flashing — A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on your vehicle. Diagnosis and service might be required. Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service might be required.


If the Light is Flashing The following can prevent more serious damage to your vehicle: (cid:127) Reduce vehicle speed. (cid:127) Avoid hard accelerations. (cid:127) Avoid steep uphill grades.


If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.


If the light stops flashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the ignition off, wait at least 10 seconds, and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still flashing, follow the previous steps and see your dealer/retailer for service as soon as possible.


3-35


(cid:127) (cid:127) (cid:127) If the Light Is On Steady You might be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off.


Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality causes the engine not to run as efficiently as designed. You might notice this as stalling after start-up, stalling when you put the vehicle into gear, misfiring, hesitation on acceleration, or stumbling on acceleration — these conditions might go away once the engine is warmed up. This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer/retailer can check the vehicle. Your dealer/retailer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed.


3-36


Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced the battery or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your dealer/retailer can prepare the vehicle for inspection.


Oil Pressure Light


{CAUTION:


Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches fire. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced.


Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil.


This light will come on briefly when you start your engine. If it does not, have your vehicle serviced.


When the light comes on and stays on, it means that oil is not flowing through your engine properly. You could be low on oil and you might have some other system problem.


3-37


Change Engine Oil Light


Fog Lamp Light


If this light comes on and stays on for 30 seconds, it means that service is required for your vehicle.


The fog lamp light will come on when the fog lamps are in use.


A CHANGE OIL SOON message will appear on the DIC. For more information see DIC Warnings and Messages on page 3-49. After having the oil changed you will need to reset the light. See Engine Oil on page 5-15, and Scheduled Maintenance on page 6-4 for more information. Security Light


The light will go out when the fog lamps are turned off. See Fog Lamps on page 3-15 for more information. Cruise Control Light


This light comes on whenever you set the cruise control.


For information regarding this light and the vehicle’s security system, see Content Theft-Deterrent on page 2-17, and PASS-Key® III+ Operation on page 2-18.


The light goes out when the cruise control is turned off. See Cruise Control on page 3-10 for more information.


3-38


Reduced Engine Power Light


Highbeam On Light


Your vehicle has a reduced engine power light.


This light comes on when the high-beam headlamps are in use.


This light, along with the service vehicle soon light, will be displayed when a noticeable reduction in the vehicle’s performance may occur. Stop the vehicle and turn off the ignition. Wait for 10 seconds and restart your vehicle. This may correct the condition. See Service Vehicle Soon Light on page 3-41 for more information. The vehicle may be driven at a reduced speed when the reduced engine power light is on, but acceleration and speed may be reduced. The performance may be reduced until the next time you drive your vehicle. If this light stays on, see your dealer/retailer as soon as possible for diagnosis and repair.


See Headlamp High/Low-Beam Changer on page 3-8
for more information. Service All-Wheel Drive Light


This light is located in the center of your instrument panel cluster.


This light and the SERVICE ALL WHEEL DRIVE message in the Driver Information Center (DIC) will come on and stay on to indicate that there may be a problem with the drive system and service is required.


3-39


See All-Wheel Drive (AWD) System on page 4-8
and DIC Warnings and Messages on page 3-49 for more information. All-Wheel Drive Disabled Light


This light will come on when the rear drive system is overheating.


Gate Ajar Light


If this light comes on, your liftgate is not completely closed. Driving with the liftgate open can cause carbon monoxide (CO) to enter the vehicle.


An ALL WHEEL DRIVE OFF message will appear in the Driver Information Center (DIC) too. This light will turn off when the rear drive system cools down. If this light stays on for a while, you need to reset the light. To reset the light, turn the ignition off and then back on again. If the light stays on, see your dealer/retailer right away. See All-Wheel Drive on page 5-42 and DIC Warnings and Messages on page 3-49 for more information.


See Engine Exhaust on page 2-35 for more information.


Door Ajar Light


This light will come on when a door is ajar.


Do not drive with a door ajar.


3-40


Service Vehicle Soon Light


For vehicles with this light, it will come on if a condition exists that may require the vehicle to be taken in for service.


If the light comes on, see your dealer/retailer for service as soon as possible.


Fuel Gage


When the ignition is on, the fuel gage tells you about how much fuel you have left in your tank.


When the indicator nears empty, the low fuel light will come on. You still have a little fuel left, but you should get more soon. See Low Fuel Warning Light on page 3-42 for more information. Here are four things that some owners ask about. None of these show a problem with your fuel gage: (cid:127) At the service station, the fuel pump shuts off


before the gage reads full. It takes a little more or less fuel to fill up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to fill the tank. The gage moves a little when you turn a corner or speed up. The gage takes a few seconds to stabilize after the ignition is turned on, and will go back to empty when you turn the ignition off.


For your fuel tank capacity, see Capacities and Specifications on page 5-107.


3-41


(cid:127) (cid:127) (cid:127) Low Fuel Warning Light


This light is located in the fuel gage. For more information see Fuel Gage on page 3-41.


This light comes on when the fuel tank is low on fuel. When you add fuel the light should go off. If it does not, have your vehicle serviced. A “Fuel Level LOW” message also appears in the Driver Information Center (DIC). See Fuel Gage on page 3-41 for more information. Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). All messages will appear in the DIC display located in the center of the instrument panel cluster. The DIC buttons are located on the center of the instrument panel.


The DIC comes on when the ignition is on. After a short delay, the DIC will display the information that was last displayed before the engine was turned off. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected. The top of the DIC display shows the shift lever position indicator. See Automatic Transmission Operation (3.4L V6 with 5-Speed) on page 2-24 or Automatic Transmission Operation (3.6L V6 with 6-Speed) on page 2-27 for more information. If your vehicle has these feature, the DIC also displays the compass direction and the outside air temperature when viewing the trip and fuel information. If there is a problem with the system that controls the temperature display, the numbers will be replaced with dashes. If this occurs, have the vehicle serviced by your dealer/retailer. If an abnormal temperature reading is displayed for an extended period of time, consult your dealer/retailer. Under certain circumstances, especially when the engine is idling, a delay updating the temperature display is normal. The DIC also allows some features to be personalized. See DIC Vehicle Personalization on page 3-58 for more information.


3-42


DIC Operation and Displays The DIC has different displays which can be accessed by pressing the DIC buttons located on the center of the instrument panel. DIC Buttons


The buttons are the trip/fuel, vehicle information, and set/reset buttons. The button functions are detailed in the following pages.


3 (Trip/Fuel): Press this button to scroll through the trip and fuel displays. See “Trip/Fuel Menu Items” following for more information on these displays.


T (Vehicle Information): Press this button to scroll through the vehicle information displays and to personalize the feature settings on your vehicle. See “Vehicle Information Menu Items” following and DIC Vehicle Personalization on page 3-58 for more information on these displays.


V (Set/Reset): Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC. Trip/Fuel Menu Items


3 (Trip/Fuel): Press this button to scroll through the following displays: ODOMETER Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km). This display will also show the outside air temperature in either degrees Fahrenheit (°F) or degrees Celsius (°C). To change the DIC display to English or metric units, see “UNITS” later in this section. TRIP Press the trip/fuel button until TRIP displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for the trip odometer. This display will also show the outside

Loading...
x