2016 Chevrolet Cruze Owners Manual

Tire Pressure Tires need the correct amount of air pressure to operate effectively.

Caution

Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:

. Tire overloading and

overheating which could lead to a blowout.

. Premature or irregular wear. . Poor handling. . Reduced fuel economy. Overinflated tires, or tires that have too much air, can result in:

. Unusual wear. . Poor handling. . Rough ride. . Needless damage from

road hazards.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures. The recommended pressure is the minimum air pressure needed to support the vehicle's maximum load carrying capacity. See Vehicle Load Limits 0 177
How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.

ii

When to Check Check the tires once a month or more. Do not forget the compact spare, if the vehicle has one. The cold compact spare tire pressure should be at 420 kPa (60 psi). See Compact Spare Tire 0 289

ii

How to Check Use a good quality pocket-type gauge to check tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air. Recheck the tire pressure with the tire gauge.

Vehicle Care

263

Put the valve caps back on the valve stems to keep out dirt and moisture and prevent leaks. Use only valve caps designed for the vehicle by GM. TPMS sensors could be damaged and would not be covered by the vehicle warranty.

Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

264

Vehicle Care

tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has

not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or

alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation 0 264
See Radio Frequency Statement 0 333

ii

ii

Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmits the tire pressure readings to a receiver in the vehicle.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and needs to be inflated to the proper pressure. A Tire and Loading Information label, attached to your vehicle, shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load , for an example of the Limits 0 177
Tire and Loading Information label and its location. Also see Tire Pressure 0 262
The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection 0 267
Tires 0 255

, Tire Rotation 0 268

and

ii

ii

ii

ii

ii

Vehicle Care

265

Caution

Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use only the GM approved tire sealant available through your dealer or included in the vehicle.

ii

for

Factory-installed Tire Inflator Kits use a GM approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See Tire Sealant and Compressor Kit 0 276
information regarding the inflator kit materials and instructions. TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for

ii

When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the Tire and Loading Information label. See Vehicle Load Limits 0 177
A message to check the pressure in a specific tire displays in the Driver Information Center (DIC). The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed. For additional information and details about the DIC operation and displays see Driver Information Center (DIC) 0 112

ii

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

266

Vehicle Care

about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message also displays. The malfunction light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause these to come on are: . One of the road tires has been

replaced with the spare tire. The spare tire does not have a TPMS sensor. The malfunction light and DIC message should go off after the road tire is replaced and the sensor matching process is performed successfully. See “TPMS Sensor Matching Process” later in this section.

. The TPMS sensor matching process was not done or not completed successfully after rotating the tires. The malfunction light and the DIC message should go off after successfully completing the sensor matching process. See "TPMS Sensor Matching Process" later in this section.

. One or more TPMS sensors are

missing or damaged. The malfunction light and the DIC message should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer for service.

. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended could prevent the TPMS from functioning properly. See Buying New Tires 0 270

ii

. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.

If the TPMS is not functioning properly it cannot detect or signal a low tire condition. See your dealer for service if the TPMS malfunction light and DIC message comes on and stays on.

TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the vehicle’s tires or replacing one or more of the TPMS sensors. The TPMS sensor matching process should also be performed after replacing a spare tire with a road tire containing the TPMS sensor. The malfunction light and the DIC message should go off at the next ignition cycle. The sensors are matched to the tire/wheel positions, using a TPMS relearn tool, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear. See your dealer for service or to purchase a relearn tool. A TPMS relearn tool can also be purchased. See Tire Pressure Monitor Sensor Activation Tool at www.gmtoolsandequipment.com or call 1-800-GM TOOLS (1-800-468-6657).

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. The TPMS sensor matching process is: 1. Set the parking brake. 2. Turn the ignition to ON/RUN

with the engine off or place the vehicle power mode in ON/ RUN/START. See Ignition Positions (Keyless Access) or Ignition Positions 0 181
(Key Access) 0 183

ii

3. Use the MENU button to select

ii

the Vehicle Information Menu in the Driver Information Center (DIC).

A message asking if the process should begin should appear.

6. Press the SET/CLR button

again to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen.

7. Start with the driver side

front tire.

8. Place the relearn tool against

the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.

4. Use the thumbwheel to scroll to

9. Proceed to the passenger side

the Tire Pressure Menu Item screen.

front tire, and repeat the procedure in Step 8.

5. Press the SET/CLR button to

10. Proceed to the passenger side

begin the sensor matching process.

rear tire, and repeat the procedure in Step 8.

Vehicle Care

267

11. Proceed to the driver side rear tire, and repeat the procedure in Step 8. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.

12. Turn the ignition to LOCK/OFF

or press STOP to turn the ignition off.

13. Set all four tires to the

recommended air pressure level as indicated on the Tire and Loading Information label.

Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

Tires are rotated to achieve a more uniform wear for all tires. The first rotation is the most important. Anytime unusual wear is noticed, rotate the tires as soon as possible, check for proper tire inflation pressure, and check for damaged tires or wheels. If the unusual wear continues after the rotation, check the wheel alignment. See When It Is Time and Wheel for New Tires 0 269
Replacement 0 273

ii

ii

268

Vehicle Care

Replace the tire if: . The indicators at three or

more places around the tire can be seen.

. There is cord or fabric

showing through the tire's rubber.

. The tread or sidewall is

cracked, cut, or snagged deep enough to show cord or fabric.

. The tire has a bump, bulge,

or split.

. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.

Tire Rotation Tires should be rotated every 12 000 km (7,500 mi). See Maintenance Schedule 0 307

ii

Use this rotation pattern when rotating the tires. Do not include the compact spare tire in the tire rotation. Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated. See and Vehicle Tire Pressure 0 262
Load Limits 0 177
Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation 0 264
Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications 0 321
{ Warning

ii

ii

ii

ii

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come (Continued)

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

Warning (Continued)

off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.

When It Is Time for New Tires Factors such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.

ii

ii

Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. See Tire and Tire Rotation Inspection 0 267
0 268
The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple factors including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. GM recommends that tires, including the spare if equipped, be replaced after six years, regardless of tread wear. The

Vehicle Care

269

tire manufacture date is the last four digits of the DOT Tire Identification Number (TIN) which is molded into one side of the tire sidewall. The first two digits represent the week (01–52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. This area should be free of grease, gasoline, or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

270

Vehicle Care

Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating. GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number

ii

will be followed by MS for mud and snow. See Tire Sidewall Labeling 0 257
GM recommends replacing worn tires in complete sets of four. Uniform tread depth on all tires will help to maintain the performance of the vehicle. Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. If proper rotation and maintenance have been done, all four tires should wear out at about the same time. See Tire Rotation 0 268
necessary to replace only one axle set of worn tires, place the new tires on the rear axle. Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y and ZR speed rated tires. Never exceed the winter

. However, if it is

ii

tires’ maximum speed capability when using winter tires with a lower speed rating.

{ Warning

Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death. Only your dealer or authorized tire service center should mount or dismount the tires.

{ Warning

Mixing tires of different sizes, brands, or types may cause loss of control of the vehicle, resulting in a crash or other vehicle damage. Use the correct size, brand, and type of tires on all wheels.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

{ Warning

Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving. A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.

If the vehicle tires must be replaced with a tire that does not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction (radial) as the original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed. See Tire Pressure Monitor System 0 263

ii

The Tire and Loading Information label indicates the original equipment tires on the vehicle. See Vehicle Load Limits 0 177

ii

Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, roll bars, traction control, electronic stability control, or All-Wheel Drive, the performance of these systems can also be affected.

{ Warning

If different sized wheels are used, there may not be an acceptable level of performance and safety if (Continued)

Vehicle Care

271

Warning (Continued)

tires not recommended for those wheels are selected. This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems developed for the vehicle, and have them properly installed by a GM certified technician.

See Buying New Tires 0 270
Accessories and Modifications 0 220

ii

and

ii

Uniform Tire Quality Grading The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

272

Vehicle Care

most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter tires, compact spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:

Treadwear 200 Traction AA Temperature A All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing are not necessary on a regular basis. Consider an alignment check if there is unusual tire wear or the vehicle is significantly pulling to one side or the other. Some slight pull to the left or right, depending on the crown of the road and/or other road surface variations such as troughs or ruts, is normal. If the vehicle is vibrating when driving on a smooth road, the tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.

Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it.

Vehicle Care

273

Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.

{ Warning

Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

274

Vehicle Care

Caution

The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis.

Used Replacement Wheels

{ Warning

Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.

Tire Chains

{ Warning

Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause loss of control and a crash. Use another type of traction device only if its manufacturer recommends it for the vehicle's tire size combination and road conditions. Follow that manufacturer's instructions. To avoid vehicle damage, drive slow and readjust or remove the traction device if it contacts the vehicle. Do not spin the wheels. If traction devices are used, install them on the front tires.

ii

If a Tire Goes Flat It is unusual for a tire to blowout while driving, especially if the tires are maintained properly. See Tires . If air goes out of a tire, it is 0 255
much more likely to leak out slowly. But if there ever is a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

{ Warning

Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.

{ Warning

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could (Continued)

Vehicle Care

275

Warning (Continued)

Warning (Continued)

be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

ii

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers 0 130
{ Warning Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall causing injury or death. Find a level place to change the tire. To help prevent the vehicle from moving:

1. Set the parking brake firmly. (Continued)

2. Put an automatic

transmission in P (Park) or a manual transmission in 1 (First) or R (Reverse).

3. Turn off the engine and do not restart while the vehicle is raised.

4. Do not allow passengers to

remain in the vehicle.

5. Place wheel blocks,

if equipped, on both sides of the tire at the opposite corner of the tire being changed.

This vehicle may come with a jack, spare tire, and wheel block(s) or a tire sealant and compressor kit. To use the jacking equipment to change a spare tire safely, follow the instructions below. Then see . To use the tire Tire Changing 0 283
sealant and compressor kit, see Tire Sealant and Compressor Kit 0 276

ii

ii

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

276

Vehicle Care

1. Wheel Block (If Equipped) 2. Flat Tire

The following information explains how to repair or change a tire.

Tire Sealant and Compressor Kit

{ Warning

Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust 0 191

ii

{ Warning

Overinflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure.

{ Warning

Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.

To use the wheel blocks, if equipped, lift the wheel block and lock it into place. When the vehicle has a flat tire (2), use the following example as a guide to assist in the placement of the wheel blocks (1), if equipped.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

If this vehicle has a tire sealant and compressor kit, there may not be a spare tire, tire changing equipment, and on some vehicles there may not be a place to store a tire. The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (0.25 inch) in the tread area of the tire. It can also be used to inflate an under inflated tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program 0 327
Read and follow all of the tire sealant and compressor kit instructions.

ii

Vehicle Care

277

before its expiration date. Replacement sealant canisters are available at your local dealer. See “Removal and Installation of the Sealant Canister” following. There is only enough sealant to seal one tire. After usage, the sealant canister and sealant/air hose assembly must be replaced. See “Removal and Installation of the Sealant Canister” following. Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire

The kit includes:

1. Air Compressor 2. Tire Sealant Canister 3. Power Plug 4. On/Off Button 5. Pressure Gauge 6. Air Only Hose (Black) 7. Sealant/Air Hose (Clear)

Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

278

Vehicle Care

When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers 0 130
See If a Tire Goes Flat 0 274
for other important safety warnings. Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and

ii

ii

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit 0 282
Make sure the on/off button (4) is in the off (O) position.

ii

2. Unwrap the sealant/air hose (7)

and the power plug (3).

3. Place the kit on the ground.

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

4. Remove the valve stem cap from the flat tire by turning it counterclockwise.

5. Attach the sealant/air hose (7) onto the tire valve stem. Turn it clockwise until it is tight.

6. Plug the power plug (3) into the

ii

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets 0 97
If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

7. Start the vehicle. The vehicle must be running while using the air compressor.

8. Press the on/off button (4) to

turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gauge (5) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inflates with air only. Inflate the tire to the recommended inflation pressure using the pressure gauge (5). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure 0 262
The pressure gauge (5) may read higher than the actual tire pressure while the compressor

ii

9.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached.

Caution

If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program 0 327

ii

10. Press the on/off button (4) to

turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire.

Therefore, Steps 11–17 must be done immediately after Step 10. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

11. Unplug the power plug (3) from

the accessory power outlet in the vehicle.

12. Turn the sealant/air hose (7)

counterclockwise to remove it from the tire valve stem.

13. Replace the tire valve

stem cap.

14. Replace the sealant/air hose

(7), and the power plug (3) back in their original location.

15.

If the flat tire was able to inflate to the recommended inflation pressure, remove the

Vehicle Care

279

maximum speed label from the sealant canister (2) and place it in a highly visible location. Do not exceed the speed on this label until the damaged tire is repaired or replaced.

16. Return the equipment to its

17.

original storage location in the vehicle. Immediately drive the vehicle 8 km (5 mi) to distribute the sealant in the tire.

18. Stop at a safe location and

check the tire pressure. Refer to Steps 1–11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured).” If the tire pressure has fallen more than 68 kPa (10 psi) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program 0 327

ii

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

280

Vehicle Care

If the tire pressure has not dropped more than 68 kPa (10 psi) from the recommended inflation pressure, inflate the tire to the recommended inflation pressure.

19. Wipe off any sealant from the

wheel, tire or vehicle.

20. Dispose of the used sealant canister (2) and sealant/air hose (7) assembly at a local dealer or in accordance with local state codes and practices.

21. Replace it with a new canister

available from your dealer.

22. After temporarily sealing a tire

using the tire sealant and compressor kit, take the vehicle to an authorized dealer within 161 km (100 mi) of driving to have the tire repaired or replaced.

Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant:

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers 0 130
See If a Tire Goes Flat 0 274
for other important safety warnings.

ii

ii

1. Remove the tire sealant and

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit 0 282

ii

2. Unlock the air only hose (6)

from the sealant canister (2) by pulling up on the lever.

3. Pull the air only hose (6) from

the sealant canister (2).

4. Remove the power plug (3) from the air compressor (1). 5. Place the kit on the ground.

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

6. Remove the tire valve stem

cap by turning it counterclockwise.

7. Attach the air only hose (6) onto the tire valve stem and press the lever down to secure it.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

8. Plug the power plug (3) into the

ii

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets 0 97
If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

9. Start the vehicle. The vehicle must be running while using the air compressor.

10. Press the on/off button (4) to

11.

turn the compressor on. The compressor will inflate the tire with air only. Inflate the tire to the recommended inflation pressure using the pressure gauge (5). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure 0 262

ii

Vehicle Care

281

The tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inflate air mattresses, balls, etc. Removal and Installation of the Sealant Canister To remove the sealant canister:

1. Unlock the air only hose (6)

from the sealant canister (2) by pulling up on the lever.

2. Pull the air only hose (6) from

the sealant canister (2).

3. Unwrap the sealant/air hose (7)

from the compressor (1).

The pressure gauge (5) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate reading. The compressor may be turned on/ off until the correct pressure is reached.

12. Press the on/off button (4) to

turn the tire sealant and compressor kit off. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

13. Unplug the power plug (3) from

the accessory power outlet in the vehicle.

14. Disconnect the air only hose

(6) from the tire valve stem by lifting the lever. Replace the tire valve stem cap.

15. Replace the air only hose (6)

and the power plug (3) back in its original location.

16. Place the equipment in the

original storage location in the vehicle.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

282

Vehicle Care

3. Wrap the sealant/air hose (7)

around the air compressor channel to stow it in its original location.

4. Push the air only hose (6) onto

the sealant canister inlet and push the lever down.

Storing the Tire Sealant and Compressor Kit The tire sealant and compressor kit is located in the trunk, under the load floor, behind an access panel. To remove the kit: 1. Open the trunk. See Trunk

0 37

ii

2. Turn the left knob

counterclockwise and the right knob clockwise, 90 degrees, at the same time. Then pull the access panel rearward and up to remove it.

4. Turn the sealant canister (2) so

the inflator filling hose is aligned with the slot in the compressor.

5. Lift the sealant canister (2)

from the compressor and replace with a new sealant canister. See your dealer for more information.

To install a new sealant canister: 1. Align the sealant/air hose (7)

with the slot in the air compressor.

2. Push the sealant canister (2)

down and turn it clockwise.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

Tire Changing

Removing the Spare Tire and Tools To access the spare tire and tools:

Vehicle Care

283

tether (2) from the stow rod, the tool bag (3) containing the wheel wrench and wheel blocks, and the spare tire (4). 4. Remove the jack, jack handle

extension, and two-piece wrench, if equipped.

3. Pull the inflator kit rearward. Squeeze the two tabs of the quick release buckle to remove the tire sealant and compressor kit.

To store the inflator kit, reverse the steps.

1. Retainer Nut 2. Tool Bag Tether 3. Tool Bag 4. Spare Tire

1. Open the trunk. See Trunk

0 37

ii

2. Lift the load floor. 3. Turn the retainer nut (1)

counterclockwise to remove it. Then remove the tool bag

1. Three-Piece Wrench 2. Hex Head Jack 3. Jack Handle Extension 4. Coin/Pierce Jack 5. Two-Piece Wrench

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

284

Vehicle Care

This vehicle may have one of the following: A coin/pierce jack (4), a jack handle extension (3), and a two-piece wrench (5), or a hex head jack (2) and three-piece wrench (1). Removing the Flat Tire and Installing the Spare Tire This vehicle may have aluminum wheels with exposed wheel nuts. Use the wheel wrench to loosen all the wheel nuts. Do not remove them yet. Or, this vehicle may have steel wheels with plastic covers.

To remove the plastic covers and wheel nut caps, loosen the plastic nut caps with the wheel wrench in a counterclockwise direction. If needed, finish loosening them with your fingers. The plastic nut caps will not come off. If needed, use the flat end of the wheel wrench and pry along the edge of the cover until it comes off. The edge of the wheel cover could be sharp, so do not try to remove it with your bare hands. Do not drop the cover or lay it face down, as it could become scratched or damaged. Store the wheel cover in the trunk until the flat tire is repaired or replaced. Once you have removed the wheel cover, use the following procedure to remove the flat tire and install the spare tire. 1. Do a safety check before

proceeding. See If a Tire Goes Flat 0 274
information.

for more

ii

2. Turn the wheel wrench

counterclockwise once on each wheel nut to loosen it. Do not remove them yet.

3. Place the jack near the flat tire. 4. Place the wheel blocks on both sides of the tire at the opposite corner of the tire being changed. See If a Tire Goes for proper wheel Flat 0 274
block placement.

ii

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

Vehicle Care

285

7.

If you have a coin/pierce jack, attach the jack handle extension to the jack by sliding the hook through the end of the jack. If you have a hex head jack, place the hex tube end of the wrench over the hex head of the jack.

Caution

Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty.

5.

If this vehicle is the RS model, locate the front or rear jack cover on the rocker molding near the tire being changed. Place your hand behind the edge of the cover on the rocker molding. Pull down and out to remove the cover. The cover will remain attached to the molding by a tether.

6. Place the jack under the

vehicle.

8. Position the jack lift head at the

jack location nearest the flat tire. The location is indicated by a notch in the flange. The jack must not be used in any other position.

{ Warning

Getting under a vehicle when it is lifted on a jack is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

286

Vehicle Care

{ Warning

Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

{ Warning

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

Hex Head Jack Shown, Coin/

Pierce Jack Similar

9. Raise the jack by turning the

handle clockwise until it comes in contact with the notch in the flange.

Make sure the jack lift head notch is placed in the flange notch. Raise the vehicle far enough off the ground so there is enough room for the road tire to clear the ground.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

Warning (Continued)

towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

10. Remove all of the wheel nuts. 11. Remove the flat tire. { Warning

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper (Continued)

12. Remove any rust or dirt from

the wheel bolts, mounting surfaces, and spare wheel.

13. Place the compact spare tire

on the wheel-mounting surface.

Vehicle Care

287

{ Warning

Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.

14. Reinstall the wheel nuts.

Tighten each nut by hand until the wheel is held against the hub.

15. Lower the vehicle by turning

the jack handle counterclockwise.

{ Warning

Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel

(Continued)

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

288

Vehicle Care

Warning (Continued)

nuts. See Capacities and Specifications 0 321
equipment wheel nut torque specifications.

ii

for original

Caution

Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications for the wheel nut torque 0 321
specification.

ii

16. Tighten the wheel nuts firmly in

a crisscross sequence, as shown.

17. Lower the jack all the way and remove the jack from under the vehicle.

18. Tighten the wheel nuts firmly

with the wheel wrench.

Front Jack Cover Shown, Rear

Jack Cover Similar

19.

If this vehicle is the RS model, snap the jack cover back into place.

20. Remove the wheel blocks and

return them to their proper storage location.

When reinstalling the wheel cover or center cap on the full-size tire, tighten all five plastic caps hand snug with the aid of the wheel wrench and tighten them with the wheel wrench an additional one-quarter of a turn.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

Caution

Wheel covers will not fit on the vehicle's compact spare. If you try to put a wheel cover on the compact spare, the cover or the spare could be damaged.

Storing a Flat or Spare Tire and Tools

{ Warning

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

Storing the Flat Tire and Tools 1. Replace the wheel wrench and

wheel blocks in the tool bag. 2. Remove the foam container

from the rear storage compartment.

Coin/Pierce Jack Shown, Hex

Head Jack Similar

3. Place the flat tire in the storage

compartment with the valve stem down.

4. Place the jack and jack handle

extension, if the vehicle has one, in the foam container.

5. Place the foam container inside

the flat tire. Align the hole with the stow rod.

6. Place the tool bag tether over the stow rod and the tool bag rear of the flat tire.

7. Turn the retainer nut clockwise

until tight.

Vehicle Care

289

8. Replace the load floor.

The load floor may not lay flat. The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can.

Storing the Compact Spare Tire and Tools Reverse the instructions for removing the spare tire and tools to store the compact spare tire.

Compact Spare Tire

{ Warning

Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.

If this vehicle has a compact spare tire, it was fully inflated when new; however, it can lose air over time.

Chevrolet Cruze Limited Owner Manual 9282844) - 2016 - crc - 9/3/15

(GMNA-Localizing-U.S./Canada-

290

Vehicle Care

Check the inflation pressure regularly. It should be 420 kPa (60 psi). Stop as soon as possible and check that the spare tire is correctly inflated after being installed on the vehicle. The compact spare tire is designed for temporary use only. The vehicle will perform differently with the spare tire installed and it is recommended that the vehicle speed be limited to 80 km/h (50 mph). To conserve the tread of the spare tire, have the standard tire repaired or replaced as soon as convenient and return the spare tire to the storage area. When using a compact spare tire, the AWD (if equipped), ABS, and