2015 Chevrolet Cruze Owners Manual

jack (2) and three-piece wrench (1).

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (75,1)

Vehicle Care

10-75

Removing the Flat Tire and Installing the Spare Tire This vehicle may have aluminum wheels with exposed wheel nuts. Use the wheel wrench to loosen all the wheel nuts. Do not remove them yet. Or, this vehicle may have steel wheels with plastic covers.

To remove the plastic covers and wheel nut caps, loosen the plastic nut caps with the wheel wrench in a counterclockwise direction.

If needed, finish loosening them with your fingers. The plastic nut caps will not come off. If needed, use the flat end of the wheel wrench and pry along the edge of the cover until it comes off. The edge of the wheel cover could be sharp, so do not try to remove it with your bare hands. Do not drop the cover or lay it face down, as it could become scratched or damaged. Store the wheel cover in the trunk until the flat tire is repaired or replaced. Once you have removed the wheel cover, use the following procedure to remove the flat tire and install the spare tire. 1. Do a safety check before

proceeding. See If a Tire Goes Flat on page 10-64 for more information.

2. Turn the wheel wrench

counterclockwise once on each wheel nut to loosen it. Do not remove them yet.

3. Place the jack near the flat tire. 4. Place the wheel blocks on both sides of the tire at the opposite corner of the tire being changed. See If a Tire Goes Flat on page 10-64 for proper wheel block placement.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (76,1)

10-76

Vehicle Care

7.

If you have a coin/pierce jack, attach the jack handle extension to the jack by sliding the hook through the end of the jack. If you have a hex head jack, place the hex tube end of the wrench over the hex head of the jack.

{ Caution

Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty.

5.

If this vehicle is the RS model, locate the front or rear jack cover on the rocker molding near the tire being changed. Place your hand behind the edge of the cover on the rocker molding. Pull down and out to remove the cover. The cover will remain attached to the molding by a tether.

6. Place the jack under the vehicle.

8. Position the jack lift head at the jack location nearest the flat tire. The location is indicated by a notch in the flange. The jack must not be used in any other position.

{ Warning

Getting under a vehicle when it is lifted on a jack is dangerous. If the vehicle slips off the jack, you could be badly injured or

(Continued)

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (77,1)

Vehicle Care

10-77

Warning (Continued)

killed. Never get under a vehicle when it is supported only by a jack.

{ Warning

Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

{ Warning

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

Hex Head Jack Shown, Coin/

Pierce Jack Similar

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (78,1)

10-78

Vehicle Care

9. Raise the jack by turning the

handle clockwise until it comes in contact with the notch in the flange.

Warning (Continued)

an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

Make sure the jack lift head notch is placed in the flange notch. Raise the vehicle far enough off the ground so there is enough room for the road tire to clear the ground.

10. Remove all of the wheel nuts. 11. Remove the flat tire. { Warning

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In

(Continued)

12. Remove any rust or dirt from

the wheel bolts, mounting surfaces, and spare wheel.

13. Place the compact spare tire

on the wheel-mounting surface.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (79,1)

Vehicle Care

10-79

{ Warning

Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.

14. Reinstall the wheel nuts.

Tighten each nut by hand until the wheel is held against the hub.

15. Lower the vehicle by turning

the jack handle counterclockwise.

{ Warning

Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the

(Continued)

Warning (Continued)

aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12-2 for original equipment wheel nut torque specifications.

{ Caution

Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 12-2 for the wheel nut torque specification.

16. Tighten the wheel nuts firmly in

a crisscross sequence, as shown.

17. Lower the jack all the way and remove the jack from under the vehicle.

18. Tighten the wheel nuts firmly

with the wheel wrench.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (80,1)

10-80

Vehicle Care

{ Caution

2. Remove the foam container from

the rear storage compartment.

Wheel covers will not fit on the vehicle's compact spare. If you try to put a wheel cover on the compact spare, the cover or the spare could be damaged.

Storing a Flat or Spare Tire and Tools

{ Warning

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

Storing the Flat Tire and Tools 1. Replace the wheel wrench and

wheel blocks in the tool bag.

Front Jack Cover Shown, Rear

Jack Cover Similar

19.

If this vehicle is the RS model, snap the jack cover back into place.

20. Remove the wheel blocks and

return them to their proper storage location.

When reinstalling the wheel cover or center cap on the full-size tire, tighten all five plastic caps hand snug with the aid of the wheel wrench and tighten them with the wheel wrench an additional one-quarter of a turn.

Coin/Pierce Jack Shown, Hex

Head Jack Similar

3. Place the flat tire in the storage

compartment with the valve stem down.

4. Place the jack and jack handle

extension, if the vehicle has one, in the foam container.

5. Place the foam container inside

the flat tire. Align the hole with the stow rod.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (81,1)

6. Place the tool bag tether over the stow rod and the tool bag rear of the flat tire.

7. Turn the retainer nut clockwise

until tight.

8. Replace the load floor.

The load floor may not lay flat.

The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can.

Storing the Compact Spare Tire and Tools Reverse the instructions for removing the spare tire and tools to store the compact spare tire.

Compact Spare Tire

{ Warning

Driving with more than one compact spare tire at a time could result in loss of braking and

(Continued)

Warning (Continued)

handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.

If this vehicle has a compact spare tire, it was fully inflated when new; however, it can lose air over time. Check the inflation pressure regularly. It should be 420 kPa (60 psi). Stop as soon as possible and check that the spare tire is correctly inflated after being installed on the vehicle. The compact spare tire is designed for temporary use only. The vehicle will perform differently with the spare tire installed and it is recommended that the vehicle speed be limited to 80 km/h (50 mph). To conserve the tread of the spare tire, have the standard tire repaired or replaced as soon as convenient and return the spare tire to the storage area.

Vehicle Care

10-81

When using a compact spare tire, the ABS and Traction Control systems may engage until the spare tire is recognized by the vehicle, especially on slippery roads. Adjust driving to reduce possible wheel slip.

{ Caution

When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails which can damage the tire, wheel, and other parts of the vehicle.

Do not use the compact spare on other vehicles. Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (82,1)

10-82

Vehicle Care

{ Caution

Tire chains will not fit the compact spare. Using them can damage the vehicle and the chains. Do not use tire chains on the compact spare.

Jump Starting For more information about the vehicle battery, see Battery on page 10-28. If the battery has run down, try to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.

{ Warning WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. See California Proposition 65 Warning on page 10-2.

{ Warning

Batteries can hurt you. They can be dangerous because:

. They contain acid that can

burn you.

. They contain gas that can

explode or ignite.

. They contain enough electricity to burn you.

If you do not follow these steps exactly, some or all of these things can hurt you.

{ Caution

Ignoring these steps could result in costly damage to the vehicle that would not be covered by the vehicle warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (83,1)

mounting bolt. Connect to a spot as far away from the discharged battery as possible. The jump start positive terminal on the discharged battery (2) is located in the engine compartment on the driver side of the vehicle. The jump start positive terminal (4) and negative terminal (3) are on the battery of the vehicle providing the jump start. The positive jump start connection for the discharged battery is under a trim cover. Open the cover to expose the terminal. 1. Check the other vehicle. It must

have a 12-volt battery with a negative ground system.

{ Caution

If the other vehicle does not have a 12-volt system with a negative ground, both vehicles can be

(Continued)

Vehicle Care

10-83

Caution (Continued)

damaged. Only use a vehicle that has a 12-volt system with a negative ground for jump starting.

2. Position the two vehicles so that

they are not touching.

3. Set the parking brake firmly and

put the shift lever in P (Park) with an automatic transmission, or Neutral with a manual transmission. See Shifting Into Park on page 9-23 with an automatic transmission, or Parking on page 9-25 with a manual transmission. { Caution

If any accessories are left on or plugged in during the jump starting procedure, they could be damaged. The repairs would not be covered by the vehicle

(Continued)

1.4L L4 Engine Shown, 1.8L L4

Engine, and 2.0L L4 Engine

Similar

1. Discharged Battery Negative

Grounding Point

2. Discharged Battery Positive

Terminal

3. Good Battery Negative

Terminal

4. Good Battery Positive

Terminal

The jump start negative grounding point (1) for the discharged battery is the engine block or an engine

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (84,1)

10-84

Vehicle Care

Caution (Continued)

warranty. Whenever possible, turn off or unplug all accessories on either vehicle when jump starting.

4. Turn the ignition to LOCK/OFF.

Turn off all lights and accessories in both vehicles, except the hazard warning flashers if needed.

{ Warning

An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.

{ Warning

Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.

{ Warning

Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.

5. Connect one end of the red

positive (+) cable to the positive (+) terminal on the discharged battery.

6. Connect the other end of the red

positive (+) cable to the positive (+) terminal of the good battery.

7. Connect one end of the black

negative (–) cable to the negative (–) terminal of the good battery.

8. Connect the other end of the

black negative (–) cable to the negative (–) grounding point for the discharged battery.

9. Start the engine in the vehicle with the good battery and run the engine at idle speed for at least four minutes.

10. Try to start the vehicle that had

the dead battery. If it will not start after a few tries, it probably needs service.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (85,1)

{ Caution If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.

Jumper Cable Removal Reverse the sequence exactly when removing the jumper cables.

Vehicle Care

10-85

of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground. Dolly towing is towing the vehicle with two wheels on the ground and two wheels up on a device known as a dolly. Here are some important things to consider before recreational vehicle towing:

The towing capacity of the towing vehicle. Be sure to read the tow vehicle manufacturer's recommendations.

. How far the vehicle will be

towed. Some vehicles have restrictions on how far and how long they can tow. The proper towing equipment. See your dealer or trailering professional for additional advice and equipment recommendations.

Towing the Vehicle

{ Caution

Incorrectly towing a disabled vehicle may cause damage. The damage would not be covered by the vehicle warranty.

Have the vehicle towed on a flatbed car carrier or a wheel lift tow truck. If a wheel lift tow truck is used, the drive wheels cannot contact the road while the vehicle is being towed. A wheel dolly must be used to lift all drive wheels off the ground. Consult your dealer or a professional towing service if the disabled vehicle must be towed.

Recreational Vehicle Towing Recreational vehicle towing refers to towing the vehicle behind another vehicle – such as behind a motor home. The two most common types

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (86,1)

10-86

Vehicle Care

If the vehicle is ready to be towed. Just as preparing the vehicle for a long trip, make sure the vehicle is prepared to be towed.

{ Caution

Use of a shield mounted in front of the vehicle grille could restrict airflow and cause damage to the transmission. The repairs would not be covered by the vehicle warranty. If using a shield, only use one that attaches to the towing vehicle.

Dinghy Towing (with Automatic Transmission)

Vehicles with an automatic transmission should not be towed with all four wheels on the ground. If the vehicle must be towed, a dolly should be used. See "Dolly Towing" that follows. Dinghy Towing (with Manual Transmission)

{ Caution

If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty. Do not tow the vehicle with all four wheels on the ground.

To dinghy tow the vehicle from the front with all four wheels on the ground: 1. Position the vehicle to tow and

then secure it to the towing vehicle.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (87,1)

2. Shift the transmission to Neutral. 3. Turn the ignition to ACC/

ACCESSORY.

4. To prevent the battery from draining while the vehicle is being towed, remove fuse 22, 23, 24, and 25 from the instrument panel fuse block. See Instrument Panel Fuse Block on page 10-41.

Remember to reinstall the fuses once the destination has been reached.

{ Caution

If 105 km/h (65 mph) is exceeded while towing the vehicle, it could be damaged. Never exceed 105 km/h (65 mph) while towing the vehicle.

Vehicle Care

10-87

Dolly Towing

{ Caution

Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty. Never have the vehicle towed from the rear.

Tow the vehicle with the two rear wheels on the ground and the front wheels on a dolly: To tow the vehicle with two wheels on the ground and a dolly: 1. Put the front wheels on a dolly. 2. Shift the automatic transmission

into P (Park) or a manual transmission into 1 (First) gear.

3. Set the parking brake.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (88,1)

10-88

Vehicle Care

4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing.

5. Remove the key from the

ignition.

6. Secure the vehicle to the dolly. 7. Release the parking brake.

{ Caution

Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty. Never have the vehicle towed from the rear.

Appearance Care

Exterior Care

Locks Locks are lubricated at the factory. Use a de-icing agent only when absolutely necessary, and have the locks greased after using. See Recommended Fluids and Lubricants on page 11-12. Washing the Vehicle To preserve the vehicle's finish, wash it often and out of direct sunlight.

{ Caution

Do not use petroleum-based, acidic, or abrasive cleaning agents as they can damage the vehicle's paint, metal, or plastic parts. If damage occurs, it would not be covered by the vehicle warranty. Approved cleaning

(Continued)

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (89,1)

Caution (Continued)

products can be obtained from your dealer. Follow all manufacturer directions regarding correct product usage, necessary safety precautions, and appropriate disposal of any vehicle care product.

{ Caution Avoid using high-pressure washes closer than 30 cm (12 in) to the surface of the vehicle. Use of power washers exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals.

This e symbol is on any underhood compartment electrical center that should not be power

washed. This could cause damage that would not be covered by the vehicle warranty. If using an automatic car wash, comply with the car wash instructions. The windshield wiper and rear window wiper, if equipped, must be off. Remove any accessories that may be damaged or interfere with the car wash equipment. Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. Finish Care Application of aftermarket clearcoat sealant/wax materials is not recommended. If painted surfaces are damaged, see your dealer to have the damage assessed and

Vehicle Care

10-89

repaired. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Occasional hand waxing or mild polishing should be done to remove residue from the paint finish. See your dealer for approved cleaning products. Do not apply waxes or polishes to uncoated plastic, vinyl, rubber, decals, simulated wood, or flat paint as damage can occur.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (90,1)

10-90

Vehicle Care

{ Caution Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle.

To keep the paint finish looking new, keep the vehicle garaged or covered whenever possible.

Protecting Exterior Bright Metal Moldings

{ Caution

Failure to clean and protect the bright metal moldings can result in a hazy white finish or pitting. This damage would not be covered by the vehicle warranty.

The bright metal moldings on the vehicle are aluminum or stainless steel. To prevent damage always follow these cleaning instructions: . Be sure the molding is cool to the touch before applying any cleaning solution.

. Use a cleaning solution

approved for aluminum or stainless steel. Some cleaners are highly acidic or contain alkaline substances and can damage the moldings.

. Always dilute a concentrated

cleaner according to the manufacturer’s instructions.

. Do not use chrome cleaners. . Do not use cleaners that are not

intended for automotive use.

. Use a nonabrasive wax on the vehicle after washing to protect and extend the molding finish.

Cleaning Exterior Lamps/ Lenses, Emblems, Decals and Stripes Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps, lenses, emblems, decals and stripes. Follow instructions under "Washing the Vehicle" previously in this section. Lamp covers are made of plastic, and some have a UV protective coating. Do not clean or wipe them while they are dry. Do not use any of the following on lamp covers: . Abrasive or caustic agents. . Washer fluids and other cleaning

agents in higher concentrations than suggested by the manufacturer.

. Solvents, alcohols, fuels, or other harsh cleaners. Ice scrapers or other hard items.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (91,1)

. Aftermarket appearance caps or

covers while the lamps are illuminated, due to excessive heat generated.

{ Caution

Failure to clean lamps properly can cause damage to the lamp cover that would not be covered by the vehicle warranty.

{ Caution

Using wax on low gloss black finish stripes can increase the gloss level and create a non-uniform finish. Clean low gloss stripes with soap and water only.

Air Intakes Clear debris from the air intakes, between the hood and windshield, when washing the vehicle.

Shutter System

The vehicle may have a shutter system designed to help increase fuel economy. Keep the shutter system clean for proper operation. Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean rubber blades using lint-free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the

Vehicle Care

10-91

blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking. Replace the wiper blades if they are worn or damaged. Damage can be caused by extreme dusty conditions, sand, salt, heat, sun, snow and ice. Clear ice and snow from the wiper blades before using them. If frozen to the windshield, carefully loosen them or thaw them. Damaged wiper blades should be replaced. See Wiper Blade Replacement on page 10-31 for more information. Heavy snow or ice can overload the wipers. If the wiper motor overheats, the windshield wipers will stop until the motor cools and the wiper control is turned off. See Electrical System Overload on page 10-37 for more information.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (92,1)

10-92

Vehicle Care

Weatherstrips Apply Dielectric silicone grease on weatherstrips to make them last longer, seal better, and not stick or squeak. Lubricate weatherstrips at least once a year. Hot, dry climates may require more frequent application. Black marks from rubber material on painted surfaces can be removed by rubbing with a clean cloth. See Recommended Fluids and Lubricants on page 11-12. Tires Use a stiff brush with tire cleaner to clean the tires.

{ Caution

Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/ or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.

Wheels and Trim — Aluminum or Chrome Use a soft, clean cloth with mild soap and water to clean the wheels. After rinsing thoroughly with clean water, dry with a soft, clean towel. A wax may then be applied.

{ Caution

Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium, or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash the chrome with soap and water after exposure.

{ Caution

To avoid surface damage, do not use strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels. Use only approved cleaners. Also, never drive a vehicle with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes. Damage could occur and the repairs would not be covered by the vehicle warranty.

Brake System Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect drum brake linings/shoes for wear or cracks. Inspect other brake parts, including drums, wheel cylinders,

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (93,1)

calipers, parking brake, master cylinder, brake fluid reservoir, vacuum pipes, electric vacuum pump including bracket and vent hose, if equipped. Steering, Suspension, and Chassis Components Visually inspect steering, suspension, and chassis components for damaged, loose, or missing parts or signs of wear at least once a year. Inspect power steering for proper hook-up, binding, leaks, cracks, chafing, etc. Visually check constant velocity joint boots and axle seals for leaks. Body Component Lubrication Lubricate all key lock cylinders, hood hinges, liftgate hinges, steel fuel door hinge and power assist step hinges, unless the components are plastic. Applying silicone grease

on weatherstrips with a clean cloth will make them last longer, seal better, and not stick or squeak. Underbody Maintenance At least twice a year, spring and fall use plain water to flush any corrosive materials from the underbody. Take care to thoroughly clean any areas where mud and other debris can collect. Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty.

Vehicle Care

10-93

Finish Damage Quickly repair minor chips and scratches with touch-up materials available from your dealer to avoid corrosion. Larger areas of finish damage can be corrected in your dealer's body and paint shop. Chemical Paint Spotting Airborne pollutants can fall upon and attack painted vehicle surfaces causing blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. See “Finish Care” previously in this section.

Interior Care To prevent dirt particle abrasions, regularly clean the vehicle's interior. Immediately remove any soils. Note that newspapers or dark garments that can transfer color to home furnishings can also permanently transfer color to the vehicle's interior.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (94,1)

10-94

Vehicle Care

Use a soft bristle brush to remove dust from knobs and crevices on the instrument cluster. Using a mild soap solution, immediately remove hand lotions, sunscreen, and insect repellent from all interior surfaces or permanent damage may result. Your dealer may have products for cleaning the interior. Use cleaners specifically designed for the surfaces being cleaned to prevent permanent damage. Apply all cleaners directly to the cleaning cloth. Do not spray cleaners directly on any switches or controls. Cleaners should be removed quickly. Never allow cleaners to remain on the surface being cleaned for extended periods of time. Cleaners may contain solvents that can become concentrated in the interior. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning the interior, maintain adequate ventilation by opening the doors and windows.

To prevent damage, do not clean the interior using the following cleaners or techniques: . Never use a razor or any other

sharp object to remove a soil from any interior surface.

. Never use a brush with stiff

bristles.

. Never rub any surface

aggressively or with excessive pressure.

. Do not use laundry detergents or

dishwashing soaps with degreasers. For liquid cleaners, use approximately 20 drops per 3.8 L (1 gal) of water. A concentrated soap solution will leave a residue that creates streaks and attracts dirt. Do not use solutions that contain strong or caustic soap.

. Do not heavily saturate the upholstery when cleaning.

. Do not use solvents or cleaners

containing solvents.

Interior Glass To clean, use a terry cloth fabric dampened with water. Wipe droplets left behind with a clean dry cloth. Commercial glass cleaners may be used, if necessary, after cleaning the interior glass with plain water.

{ Caution

To prevent scratching, never use abrasive cleaners on automotive glass. Abrasive cleaners or aggressive cleaning may damage the rear window defogger.

Cleaning the windshield with water during the first three to six months of ownership will reduce tendency to fog. Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (95,1)

Coated Moldings Coated moldings should be cleaned. . When lightly soiled, wipe with a

sponge or soft lint-free cloth dampened with water.

. When heavily soiled, use warm

soapy water.

Fabric/Carpet/Suede Start by vacuuming the surface using a soft brush attachment. If a rotating brush attachment is being used during vacuuming, only use it on the floor carpet. Before cleaning, gently remove as much of the soil as possible using one of the following techniques: . Gently blot liquids with a paper towel. Continue blotting until no more soil can be removed. For solid soils, remove as much as possible prior to vacuuming.

To clean: 1. Saturate a clean lint-free colorfast cloth with water. Microfiber cloth is recommended to prevent lint transfer to the fabric or carpet.

2. Remove excess moisture by

gently wringing until water does not drip from the cleaning cloth. 3. Start on the outside edge of the

soil and gently rub toward the center. Fold the cleaning cloth to a clean area frequently to prevent forcing the soil in to the fabric.

4. Continue gently rubbing the soiled area until there is no longer any color transfer from the soil to the cleaning cloth. If the soil is not completely removed, use a mild soap solution followed only by plain water.

5.

If the soil is not completely removed, it may be necessary to use a commercial upholstery

Vehicle Care

10-95

cleaner or spot lifter. Test a small hidden area for colorfastness before using a commercial upholstery cleaner or spot lifter. If ring formation occurs, clean the entire fabric or carpet. Following the cleaning process, a paper towel can be used to blot excess moisture. Cleaning High Gloss Surfaces and Vehicle Information and Radio Displays For vehicles with high gloss surfaces or vehicle displays, use a microfiber cloth to wipe surfaces. Before wiping the surface with the microfiber cloth, use a soft bristle brush to remove dirt that could scratch the surface. Then use the microfiber cloth by gently rubbing to clean. Never use window cleaners or solvents. Periodically hand wash the microfiber cloth separately, using mild soap. Do not use bleach or fabric softener. Rinse thoroughly and air dry before next use.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (96,1)

10-96

Vehicle Care

{ Caution

{ Caution

{ Caution

Do not attach a device with a suction cup to the display. This may cause damage and would not be covered by the vehicle warranty.

Instrument Panel, Leather, Vinyl, Other Plastic Surfaces, Low Gloss Paint Surfaces and Natural Open Pore Wood Surfaces Use a soft microfiber cloth dampened with water to remove dust and loose dirt. For a more thorough cleaning, use a soft microfiber cloth dampened with a mild soap solution.

Soaking or saturating leather, especially perforated leather, as well as other interior surfaces, may cause permanent damage. Wipe excess moisture from these surfaces after cleaning and allow them to dry naturally. Never use heat, steam, or spot removers. Do not use cleaners that contain silicone or wax-based products. Cleaners containing these solvents can permanently change the appearance and feel of leather or soft trim, and are not recommended.

Do not use cleaners that increase gloss, especially on the instrument panel. Reflected glare can decrease visibility through the windshield under certain conditions.

Use of air fresheners may cause permanent damage to plastics and painted surfaces. If an air freshener comes in contact with any plastic or painted surface in the vehicle, blot immediately and clean with a soft cloth dampened with a mild soap solution. Damage caused by air fresheners would not be covered by the vehicle warranty.

Cargo Cover and Convenience Net Wash with warm water and mild detergent. Do not use chlorine bleach. Rinse with cold water, and then dry completely. Care of Safety Belts Keep belts clean and dry.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (97,1)

{ Warning

Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.

Floor Mats

{ Warning

If a floor mat is the wrong size or is not properly installed, it can interfere with the pedals. Interference with the pedals can cause unintended acceleration and/or increased stopping distance which can cause a crash and injury. Make sure the floor mat does not interfere with the pedals.

Use the following guidelines for proper floor mat usage:

The original equipment floor mats were designed for your vehicle. If the floor mats need replacing, it is recommended that GM certified floor mats be purchased. Non-GM floor mats may not fit properly and may interfere with the pedals. Always check that the floor mats do not interfere with the pedals.

. Do not use a floor mat if the

vehicle is not equipped with a floor mat retainer on the driver side floor.

. Use the floor mat with the

correct side up. Do not turn it over.

. Do not place anything on top of

the driver side floor mat.

. Use only a single floor mat on

the driver side.

. Do not place one floor mat on

top of another.

Vehicle Care

10-97

Removing and Replacing the Floor Mats If equipped, pull up on the rear of the floor mat to unlock each retainer and remove.

Reinstall by lining up the floor mat retainer openings over the carpet retainers and snapping into position. Make sure the floor mat is properly secured in place. Verify the floor mat does not interfere with the pedals.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (98,1)

10-98

Vehicle Care

2 NOTES

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (1,1)

Service and Maintenance

General Information

General Information . . . . . . . . . . 11-1

Maintenance Schedule

Maintenance Schedule . . . . . . . 11-2

Special Application Services

Special Application

Services . . . . . . . . . . . . . . . . . . . . 11-8

Additional Maintenance and Care

Additional Maintenance

and Care . . . . . . . . . . . . . . . . . . . 11-9

Recommended Fluids

Recommended Fluids and

Lubricants . . . . . . . . . . . . . . . . . 11-12

Maintenance Replacement

Parts . . . . . . . . . . . . . . . . . . . . . . 11-13

Maintenance Records

Maintenance Records . . . . . . 11-15

Service and Maintenance

11-1

General Information Your vehicle is an important investment. This section describes the required maintenance for the vehicle. Follow this schedule to help protect against major repair expenses resulting from neglect or inadequate maintenance. It may also help to maintain the value of the vehicle if it is sold. It is the responsibility of the owner to have all required maintenance performed. Your dealer has trained technicians who can perform required maintenance using genuine replacement parts. They have up-to-date tools and equipment for fast and accurate diagnostics. Many dealers have extended evening and Saturday hours, courtesy transportation, and online scheduling to assist with service needs. Your dealer recognizes the importance of providing competitively priced maintenance and repair services. With trained

technicians, the dealer is the place for routine maintenance such as oil changes and tire rotations and additional maintenance items like tires, brakes, batteries, and wiper blades.

{ Caution

Damage caused by improper maintenance can lead to costly repairs and may not be covered by the vehicle warranty. Maintenance intervals, checks, inspections, recommended fluids, and lubricants are important to keep the vehicle in good working condition.

The Tire Rotation and Required Services are the responsibility of the vehicle owner. It is recommended to have your dealer perform these services every 12 000 km/7,500 mi. Proper vehicle maintenance helps to keep the vehicle in good working condition, improves fuel economy, and reduces vehicle emissions.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (2,1)

11-2

Service and Maintenance

Frequently towing a trailer.

. Used for high speed or

competitive driving.

. Used for taxi, police, or delivery

service.

Refer to the information in the Maintenance Schedule Additional Required Services - Severe chart.

{ Warning

Performing maintenance work can be dangerous and can cause serious injury. Perform maintenance work only if the required information, proper tools, and equipment are available. If they are not, see your dealer to have a trained technician do the work. See Doing Your Own Service Work on page 10-4.

Because of the way people use vehicles, maintenance needs vary. There may need to be more frequent checks and services. The Additional Required Services - Normal are for vehicles that: . Carry passengers and cargo within recommended limits on the Tire and Loading Information label. See Vehicle Load Limits on page 9-9.

. Are driven on reasonable road

surfaces within legal driving limits.

. Use the recommended fuel. See

Fuel (Gasoline) on page 9-51.

Refer to the information in the Maintenance Schedule Additional Required Services - Normal chart. The Additional Required Services - Severe are for vehicles that are: . Mainly driven in heavy city traffic

in hot weather.

. Mainly driven in hilly or

mountainous terrain.

Maintenance Schedule

Owner Checks and Services

At Each Fuel Stop . Check the engine oil level. See

Engine Oil on page 10-11.

Once a Month . Check the tire inflation

pressures. See Tire Pressure on page 10-51. Inspect the tires for wear. See Tire Inspection on page 10-57.

. Check the windshield washer

fluid level. See Washer Fluid on page 10-25.

Engine Oil Change When the CHANGE ENGINE OIL SOON DIC message displays, have the engine oil and filter changed within the next 1 000 km/600 mi. If driven under the best conditions, the engine oil life system may not indicate the need for vehicle service

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (3,1)

Service and Maintenance

11-3

for up to a year. The engine oil and filter must be changed at least once a year and the oil life system must be reset. Your trained dealer technician can perform this work. If the engine oil life system is reset accidentally, service the vehicle within 5 000 km/3,000 mi since the last service. Reset the oil life system when the oil is changed. See Engine Oil Life System on page 10-15. On vehicles with diesel engines, it is recommended to drain the diesel fuel filter of water when the oil is changed or when the WATER IN FUEL CONTACT SERVICE message displays. Tire Rotation and Required Services Every 12 000 km/ 7,500 mi Rotate the tires, if recommended for the vehicle, and perform the following services. See Tire Rotation on page 10-57.

. Check engine oil level and oil

life percentage. If needed, change engine oil and filter, and reset oil life system. See Engine Oil on page 10-11 and Engine Oil Life System on page 10-15.

. Check engine coolant level. See Engine Coolant on page 10-20. . Check windshield washer fluid

level. See Washer Fluid on page 10-25.

Inspect engine air cleaner filter. See Engine Air Cleaner/Filter on page 10-17. Inspect brake system. See Exterior Care on page 10-88.

. Visually inspect steering, suspension, and chassis components for damaged, loose, or missing parts or signs of wear. See Exterior Care on page 10-88.

. Visually inspect windshield wiper

. Check restraint system

blades for wear, cracking, or contamination. See Exterior Care on page 10-88. Replace worn or damaged wiper blades. See Wiper Blade Replacement on page 10-31.

. Check tire inflation pressures.

See Tire Pressure on page 10-51. Inspect tire wear. See Tire Inspection on page 10-57.

. Visually check for fluid leaks.

components. See Safety System Check on page 3-14.

. Visually inspect fuel system for

damage or leaks.

. Visually inspect exhaust system

and nearby heat shields for loose or damaged parts. Lubricate body components. See Exterior Care on page 10-88.

. Check starter switch. See Starter

Switch Check on page 10-29.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (4,1)

11-4

Service and Maintenance

Inspect sunroof track and seal, if equipped. See Sunroof on page 2-23.

. Check automatic transmission shift lock control function. See Automatic Transmission Shift Lock Control Function Check on page 10-30.

. Check ignition transmission lock.

See Ignition Transmission Lock Check on page 10-30.

. Check parking brake and

automatic transmission park mechanism. See Park Brake and P (Park) Mechanism Check on page 10-30.

. Check accelerator pedal for

damage, high effort, or binding. Replace if needed.

. Visually inspect gas strut for

signs of wear, cracks, or other damage. Check the hold open ability of the strut. See your dealer if service is required. . Check tire sealant expiration

date, if equipped. See Tire Sealant and Compressor Kit on page 10-66.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) - 2015 - crc - 11/24/14

Black plate (5,1)

Service and Maintenance

11-5