2012 Chevrolet Cruze Owners Manual

Instruments and Controls

as a system check. If you use remote start, if equipped, to start the vehicle, you may not see the system check. Then, after several seconds, the status indicator will light either ON or OFF, or the on or off symbol to let you know the status of the front outboard passenger frontal airbag and knee airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the front outboard passenger frontal airbag and knee airbag are allowed to inflate. If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag and passenger knee airbag.

If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ WARNING

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑11 for more information, including important safety information.

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3‑26 for important safety information. The instrument panel has a passenger airbag status indicator.

United States

Canada

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds

Chevrolet Cruze Owner Manual - 2012

Black plate (13,1)

Instruments and Controls

5-13

Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions are at acceptable levels, to produce a cleaner environment. This light comes on when the vehicle is placed in ON/RUN for key access or Service Only Mode for keyless access, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. See Ignition Positions (Key Access) on page 9‑15 or Ignition Positions (Keyless Access) on page 9‑18 for more information.

Charging System Light

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. The light turns off when the engine is started. If it does not, have the vehicle serviced by your dealer. If the light stays on, or comes on while driving, there could be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. If the malfunction indicator lamp comes on and stays on while the engine is running, this indicates that there is an OBD II problem and service is required.

Chevrolet Cruze Owner Manual - 2012

Black plate (14,1)

5-14

Instruments and Controls

Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the dealer technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on.

Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 10‑3. This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades.

If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.

If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emissions system malfunction: . Check that the fuel cap is fully

installed. See Filling the Tank on page 9‑46. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off.

Chevrolet Cruze Owner Manual - 2012

Black plate (15,1)

Instruments and Controls

5-15

. Check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9‑44. If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed.

Emissions Inspection and Maintenance Programs Some local governments may have programs to inspect the on-vehicle emission control equipment. For the inspection, the emission system test equipment is connected to the vehicle’s Data Link Connector (DLC).

The DLC is under the instrument panel to the left of the steering wheel. See your dealer if assistance is needed.

The vehicle may not pass inspection if:

The malfunction indicator lamp is on with the engine running, or if the light does not come on when the ignition is turned to ON/RUN while the engine is off. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed. The vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.

Chevrolet Cruze Owner Manual - 2012

Black plate (16,1)

5-16

Instruments and Controls

Service Vehicle Soon Light

For vehicles with this light, it comes on if a condition exists that may require the vehicle to be taken in for service. Vehicles not equipped with a light display a SERVICE VEHICLE SOON message. See Service Vehicle Messages on page 5‑32 for more information. If the light comes on, take the vehicle to your dealer for service as soon as possible. For vehicles with an uplevel cluster, this light comes on in the Driver Information Center (DIC).

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

{ WARNING

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

If the light comes on while driving, a chime sounds. Pull off the road and stop. The pedal might be harder to push or go closer to the floor. It might also take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle on page 10‑83.

Metric

English

The brake indicator light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer.

Chevrolet Cruze Owner Manual - 2012

Black plate (17,1)

Antilock Brake System (ABS) Warning Light

The Antilock Brake System (ABS) light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light comes on and stays on while driving, stop as soon as possible and turn the ignition off. Start the engine again to reset the system. If the light stays on after driving at a speed above 20 km/h (13 mph), see your dealer for service. A chime may also sound when the light comes on steady.

Instruments and Controls

5-17

If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5‑16. See Brake System Messages on page 5‑29 for all brake‐related DIC messages.

Up-Shift Light

Power Steering Warning Light

This light comes on briefly when the ignition is turned to ON/RUN as a check to show it is working. If it does not come on have the vehicle serviced by your dealer. If this light stays on, or comes on while driving, the system may not be working. If this happens, see your dealer for service.

The vehicle may have an up-shift light. It shows when to shift to the next higher gear for best fuel economy. See Manual Transmission on page 9‑33 for more information.

Chevrolet Cruze Owner Manual - 2012

Black plate (18,1)

5-18

Instruments and Controls

Traction Off Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off.

If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control System (TCS) on page 9‑37 and StabiliTrak® System on page 9‑38 for more information.

StabiliTrak® OFF Light

If the TCS is off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control System (TCS) on page 9‑37 and StabiliTrak® System on page 9‑38 for more information

Traction Control System (TCS)/StabiliTrak® Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off.

The StabiliTrak system or the Traction Control System (TCS) indicator/warning light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by the dealer. If the system is working normally, the indicator light turns off.

Chevrolet Cruze Owner Manual - 2012

Black plate (19,1)

Instruments and Controls

5-19

If the light is on and not flashing, the TCS, and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the indicator/warning light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See StabiliTrak® System on page 9‑38 and Traction Control System (TCS) on page 9‑37 for more information.

Tire Pressure Light

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Vehicle Messages (Canada Base Level) on page 5‑28
or Vehicle Messages (Canada Uplevel and United States) on page 5‑28 for more information.

Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑49 for more information.

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10‑52 for more information.

Chevrolet Cruze Owner Manual - 2012

Black plate (20,1)

5-20

Instruments and Controls

Engine Oil Pressure Light

{ WARNING

Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.

Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule for changing engine oil.

The oil pressure light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Low Fuel Warning Light

This light comes on for a few seconds when the ignition is turned on as a check to indicate it is working. If it does not come on, have it fixed. The low fuel warning light (A) comes on and a chime sounds when the vehicle is low on fuel. The light turns off when fuel is added to the fuel tank.

Chevrolet Cruze Owner Manual - 2012

Black plate (21,1)

Instruments and Controls

5-21

For vehicles with a Driver Information Center (DIC), see Driver Information Center (DIC) on page 5‑23 for more information.

Security Light

Reduced Engine Power Light

The immobilizer light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation on page 2‑14 for more information.

The reduced engine power light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer. This light, along with the service engine soon light, displays when a noticeable reduction in the vehicle's performance occurs. Stop the vehicle and turn off the ignition. Wait for 10 seconds and restart the vehicle. This might correct the condition.

The vehicle can be driven at a reduced speed when the reduced engine power light is on but acceleration and speed might be reduced. The performance could be reduced until the next time the vehicle is driven. If this light stays on, see your dealer as soon as possible for diagnosis and repair.

High-Beam On Light

The high‐beam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑2 for more information.

Chevrolet Cruze Owner Manual - 2012

Black plate (22,1)

5-22

Instruments and Controls

Daytime Running Lamps (DRL) Indicator Light

Front Fog Lamp Light

Lamps On Reminder

This light turns on whenever the Daytime Running Lamps are in use. See Daytime Running Lamps (DRL) on page 6‑2 for more information.

For vehicles with front fog lamps, this light comes on when the front fog lamps are in use. The light goes out when the front fog lamps are turned off. See Front Fog Lamps on page 6‑4 for more information.

The lamps on reminder light comes on when the lights are in use.

Chevrolet Cruze Owner Manual - 2012

Black plate (23,1)

Instruments and Controls

5-23

Cruise Control Light

Door Ajar Light

The cruise control light is white whenever the cruise control is set, and turns green when the cruise control is active. The light turns off when the cruise control is turned off. See Cruise Control on page 9‑40 for more information.

For vehicles equipped with this light, it comes on when a door is open or not securely latched. Before driving, check that all doors are properly closed. See Door Ajar Messages on page 5‑29 for more information. For vehicles with an uplevel cluster, this light comes on in the Driver Information Center (DIC).

Information Displays

Driver Information Center (DIC) The vehicle may have a Driver Information Center (DIC). The DIC displays information about your vehicle. It also displays warning messages if a system problem is detected. See Vehicle Messages (Canada Base Level) on page 5‑28
or Vehicle Messages (Canada Uplevel and United States) on page 5‑28 for more information. All messages appear in the DIC display located in the center of the instrument panel cluster. DIC Operation and Displays The DIC has different displays which can be accessed by using the DIC buttons on the turn signal lever located on the left side of the steering wheel. The DIC displays trip, fuel, and warning messages if a system problem is detected.

Chevrolet Cruze Owner Manual - 2012

Black plate (24,1)

5-24

Instruments and Controls

DIC Buttons

A. SET/CLR: Press to set or clear

the menu item displayed.

B. w x (Thumbwheel): Use to

scroll through the menus.

C. MENU: Press to display the

Trip/Fuel menu and the Vehicle Information menu. This button is also used to return to or exit the last screen displayed on the DIC.

Trip/Fuel Menu Items Press MENU on the turn signal lever until Trip/Fuel Information menu displays. Use w x to scroll through the menu items. Not all items are available on every vehicle.

The following is a list of all possible menu items:

Trip 1 or Trip 2, Average Fuel Economy, Average Vehicle Speed

. Speed, Fuel Range, Average

Fuel Economy Instantaneous Fuel Economy . Best Average Fuel Economy

Fuel Used Timer

. Digital Speed . Navigation

Trip 1 or Trip 2, Average Fuel Economy, Average Vehicle Speed This displays the current distance traveled, in either kilometers (km) or miles (mi), from the last reset for the trip odometer. The trip odometer can be reset to zero by pressing and holding the SET/CLR button while the trip odometer display is showing.

The Average Fuel Economy display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. This display is shown as . c L/100 km (mpg). Reset the average consumption by pressing SET/CLR when it is displayed. This screen also displays the average vehicle speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is based on the various vehicle speeds recorded since the last reset. This display is shown as c km/h (mph). Reset the average speed by pressing SET/CLR when it is displayed.

Chevrolet Cruze Owner Manual - 2012

Black plate (25,1)

Instruments and Controls

5-25

Speed, Fuel Range, Average Fuel Economy The top of this display includes a digital speedometer. The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset. In the center of the page is the fuel range display. This shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This display is shown as l . km (mi). Fuel range cannot be reset. Also included on this page is an instantaneous fuel economy display. The instantaneous fuel economy display shows the current fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg).

This number reflects only the fuel economy that the vehicle has right now and changes frequently as driving conditions change. This display is shown as . L/100 km (mpg). This display cannot be reset.

Instantaneous Fuel Economy The instantaneous fuel economy display shows the current fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the fuel economy that the vehicle has right now and changes frequently as driving conditions change. Unlike average economy, this display cannot be reset.

Best Average Fuel Economy The right hand side displays the best average fuel economy (AFE) that is achieved for a selected distance. The left hand side displays a running average of fuel economy for the most recently traveled selected distance.

The center bar graph displays the instantaneous fuel economy. Quickly press the SET/CLR button to display a page for selecting one of the distance options. Move the up/down arrow to choose the selection, and SET/CLR to change the setting. When viewing best AFE, a several second press and hold of SET/CLR will reset the best value. The best value will show “- - -” until the selected distance has been traveled. The display provides feedback on how current driving behavior in the bar graph affects the running average in the left display and how well recent driving compares to the best that has been achieved.

Fuel Used This display shows the approximate liters (L) or gallons (gal) of fuel that have been used since last reset. The fuel used can be reset by pressing the SET/CLR button while the Fuel Used display is showing.

Chevrolet Cruze Owner Manual - 2012

Black plate (26,1)

5-26

Instruments and Controls

Timer This display can be used as a timer. To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR.

Digital Speed The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.

Navigation This display is used for the OnStar or navigation system Turn-by-Turn guidance. See the OnStar Owner's Guide or the navigation manual, if the vehicle has navigation, for more information. Vehicle Information Menu Items Press MENU on the turn signal lever until Vehicle Information menu is displayed. Use w x to scroll through the menu items. Not all items are available on every vehicle. The following is a list of all possible menu items: . Units

Tire Pressure

. Remaining Oil Life . Coolant Temperature . Battery Voltage . Blank Display

Units Move w x to change between Metric or US when the Unit display is active. Press SET/CLR to confirm the setting. On some models, you will have to select 1, 2, or 3 for the Unit display. 1 is Imperial units, 2 is US units, and 3 is metric units. This will change the displays on the cluster and DIC to the type of measurements you select.

Tire Pressure The display may show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). On some models, this display only allows for matching of the TPMS sensors. In this case, the display will show TIRE LEARN. See Tire Pressure Monitor System on page 10‑50 and Tire Pressure Monitor Operation on page 10‑52 for more information.

Chevrolet Cruze Owner Manual - 2012

Black plate (27,1)

Instruments and Controls

5-27

The vehicle's charging system regulates voltage based on the state of the battery. The battery voltage can fluctuate while viewing this information on the DIC. This is normal. See Charging System Light on page 5‑13 for more information. If there is a problem with the battery charging system, the DIC will display a message. See Battery Voltage and Charging Messages on page 5‑28.

Blank Display This display shows no information.

Remaining Oil Life This display shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. This display may be shown as : %. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message, or Code 82, will appear on the display. See Engine Oil Messages on page 5‑30 and “Vehicle Messages (Canadian Base Level)” following. The oil should be changed as soon as possible. See Engine Oil on page 10‑9. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Maintenance Schedule on page 11‑3 for more information.

Remember, the Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system press the SET/CLR button while the Oil Life display is active. See Engine Oil Life System on page 10‑12.

Coolant Temperature This display, available on some vehicles, shows the temperature of the engine cooling system fluid in either degrees Celsius (°C) or degrees Fahrenheit (°F).

Battery Voltage This display, available on some vehicles, shows the current battery voltage. If the voltage is in the normal range, the value will display. For example, the display may read Battery Voltage 15.0 Volts.

Chevrolet Cruze Owner Manual - 2012

Black plate (28,1)

5-28

Instruments and Controls

Vehicle Messages

Vehicle Messages (Canada Base Level) DIC messages display when the status of the vehicle has changed and action may be needed to correct the condition. Multiple messages appear one after another. Press any of the DIC buttons on the turn signal lever to acknowledge and clear them from the display. More urgent messages cannot be cleared from the DIC display. All messages should be taken seriously. Clearing messages will not correct the problem. On the Canadian base level cluster, vehicle messages appear as code numbers. 25: Left front turn indicator failure 26: Left rear turn indicator failure 27: Right front turn indicator failure 28: Right rear turn indicator failure

35: Replace battery in radio remote control 53: Tighten gas cap 68: Service power steering 75: Service air conditioner 82: Change engine oil soon 84: Engine power is reduced 95: Service airbag

Vehicle Messages (Canada Uplevel and United States) DIC messages display when the status of the vehicle has changed and action may be needed to correct the condition. Multiple messages appear one after another. Press any of the DIC buttons on the turn signal lever to acknowledge and clear them from the display. More urgent messages cannot be cleared from the DIC display.

All messages should be taken seriously. Clearing messages will not correct the problem. On the Canadian uplevel cluster and on vehicles sold in the United States, vehicle messages are displayed as text. The messages and information about them follow.

Battery Voltage and Charging Messages

BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that features are disabled, this message is displayed. It means that the vehicle is trying to save the charge in the battery. Turn off unnecessary accessories to allow the battery to recharge.

Chevrolet Cruze Owner Manual - 2012

Black plate (29,1)

Instruments and Controls

5-29

Compass Messages

Door Ajar Messages

LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10‑25 for more information. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.

CAL This message is displayed when the compass needs to be calibrated. See Compass on page 5‑4. – – Two dashes will be displayed if the compass needs service. See your dealer for service.

Brake System Messages

Cruise Control Messages

BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid on page 10‑23. RELEASE PARKING BRAKE This message is displayed as a reminder that the parking brake is on. Release it before you attempt to drive.

APPLY BRAKE BEFORE CRUISE If this message displays when attempting to activate cruise control, apply the brake pedal and try again. CRUISE SET TO XXX This message displays when the cruise control is set and shows the speed it was set to. See Cruise Control on page 9‑40 for more information.

DOOR(S) OPEN A vehicle symbol will be displayed on the DIC showing which door is open along with this message. Close the door completely. HOOD OPEN This message will display when the hood is open. Close the hood completely. TRUNK OPEN This message will display when the trunk is open. Close the trunk completely.

Chevrolet Cruze Owner Manual - 2012

Black plate (30,1)

5-30

Instruments and Controls

Engine Cooling System Messages

A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down.

ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature. HIGH COOLANT TEMPERATURE This message displays if the coolant temperature is hot. See Engine Overheating on page 10‑19.

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the Oil Life System. See Engine Oil Life System on page 10‑12 and Driver Information

Center (DIC) on page 5‑23 for information on how to reset the system. See Engine Oil on page 10‑9 and Maintenance Schedule on page 11‑3 for more information. OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.

Engine Power Messages

ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination.

Chevrolet Cruze Owner Manual - 2012

Black plate (31,1)

The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible. TIGHTEN GAS CAP This message displays when the fuel cap is not on tight. Tighten the fuel cap.

Instruments and Controls

5-31

AUTOMATIC LIGHT CONTROL OFF This message is displayed when the automatic light control has been turned off. See Automatic Headlamp System on page 6‑3. XXX TURN INDICATOR FAILURE When one of the turn signals is out, this message displays to show which bulb needs to be replaced. See Bulb Replacement on page 10‑29 and Replacement Bulbs on page 10‑34 for more information on turn signal bulb replacement. TURN SIGNAL ON This message is displayed if the turn signal has been left on. Turn off the turn signal.

Key and Lock Messages

NO REMOTE DETECTED This message displays when the transmitter battery is weak on vehicles with keyless access. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2‑3 for more information. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced.

Lamp Messages

AUTOMATIC LIGHT CONTROL ON This message is displayed when the automatic light control has been turned on. See Automatic Headlamp System on page 6‑3.

Chevrolet Cruze Owner Manual - 2012

Black plate (32,1)

5-32

Instruments and Controls

Object Detection System Messages

Ride Control System Messages

PARK ASSIST OFF This message displays when the park assist system has been turned off or when there is a temporary condition causing the system to be disabled. See Ultrasonic Parking Assist on page 9‑42. SERVICE PARK ASSIST This message displays if there is a problem with the Ultrasonic Rear Parking Assist (URPA) system. Do not use this system to help you park. See Ultrasonic Parking Assist on page 9‑42 for more information. See your dealer for service.

SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). See Traction Control System (TCS) on page 9‑37. SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. See StabiliTrak® System on page 9‑38.

Airbag System Messages

SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.

Security Messages

THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.

Service Vehicle Messages

SERVICE AC SYSTEM This message displays if there is a problem with the air conditioning system. Take the vehicle to your dealer for service. SERVICE POWER STEERING This message displays if there is a problem with the power steering system. Take the vehicle to your dealer for service. SERVICE STEERING COLUMN LOCK This message displays if there is a problem with the steering column lock. Take the vehicle to your dealer for service.

Chevrolet Cruze Owner Manual - 2012

Black plate (33,1)

SERVICE VEHICLE SOON This message displays if there is a problem with the vehicle. Take the vehicle to your dealer for service.

Starting the Vehicle Messages

TURN STEERING WHEEL TURN KEY OFF THEN ON This message displays when the steering column is locked. Try turning the steering wheel while turning the vehicle off and then back on to unlock the steering column. TURN STEERING WHEEL START VEHICLE AGAIN This message displays when the steering column is locked. Try turning the steering wheel while starting the vehicle to unlock the steering column.

Instruments and Controls

5-33

Tire Messages

SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑52 for more information. TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10‑52 for more information. TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. There is also an icon with the warning that will indicate the location of the low tire.

The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑19. If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10‑42, Vehicle Load Limits on page 9‑10, and Tire Pressure on page 10‑49. You can receive more than one tire pressure message at a time. To read the other messages that may have been sent at the same time, press the SET/CLR button. The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5‑23.

Transmission Messages

SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer.

Chevrolet Cruze Owner Manual - 2012

Black plate (34,1)

5-34

Instruments and Controls

TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Vehicle Reminder Messages

ICE POSSIBLE DRIVE WITH CARE This message displays when ice conditions are possible. STEERING COLUMN IS LOCKED This message displays when the steering column is locked.

Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features. CONFIG (Configuration): Press to access the Configuration Settings menu. MENU or MENU/SEL: Press the center of this knob to enter the menus and select menu items. Turn the knob to scroll through the menus. BACK: Press to exit or move backward in a menu.

Entering the Personalization Menus 1. Press CONFIG to access the Configuration Settings menu.

2. Turn the MENU or MENU/SEL

knob to highlight Vehicle Settings. Press the CONFIG

button until Vehicle is highlighted on vehicles with a navigation system only.

3. Press the center of the MENU or

MENU/SEL knob to select the Vehicle Settings menu. The key must be in the run position.

The following list of menu items may be available: . Climate and Air Quality . Comfort and Convenience . Collision/Detection Systems

Languages Lighting

. Power Door Locks . Remote Locking, Unlocking,

Starting

. Return to Factory Settings Turn the MENU or MENU/SEL knob to highlight the menu. Press the knob to select it. Each of the menus is detailed in the following information.

Chevrolet Cruze Owner Manual - 2012

Black plate (35,1)

Instruments and Controls

5-35

Vehicles with a navigation system will display a checkmark to indicate this feature is on. Climate and Air Quality If equipped, select the Climate and Air Quality menu and the following will be displayed: . Auto Fan Speed . Air Quality Sensor . Remote Start Auto Heat Seats . Auto Defog . Auto Rear Defog

Auto Fan Speed This will allow you to select the automatic fan speed. This feature sets the climate control fan speed to maintain the interior temperature. Press the MENU or MENU/SEL knob when Auto Fan Speed is highlighted to open the menu. Turn the knob to highlight High, Medium, or Low. Press the BACK button to confirm the selection and move back to the last menu.

Air Quality Sensor This will allow you to select whether the system will operate at high or low sensitivity. Only vehicles with the automatic climate control will have this option. Press the MENU or MENU/SEL knob when Air Quality Sensor is highlighted to open the menu. Turn the knob to highlight High Sensitivity or Low Sensitivity. Press the BACK button to confirm the selection and move back to the last menu.

Remote Start Auto Heat Seats On vehicles with remote start and heated seats, the heated seats can be set to on or off. Press the MENU or MENU/SEL knob when Remote Start Auto Heat Seats is highlighted to open the menu. Turn the knob to highlight On or Off. Press the BACK button to confirm the selection and move back to the last menu.

Auto Defog When turned on and high humidity is detected, the climate control system may adjust to outside air supply and turn on the air conditioner or the heater. The fan speed may slightly increase to help prevent fogging. When high humidity is no longer detected, the system will return to its prior operation. Press the MENU or MENU/SEL knob when Auto Defog is highlighted to open the menu. Turn the knob to highlight On or Off. Press the BACK button to confirm the selection and move back to the last menu.

Auto Rear Defog When on, this feature turns on the rear defogger at vehicle start when the interior temperature is cold and fog is likely. The auto rear defog function can be disabled by pressing 1. When off, the feature can be turned on by pressing 1.

Chevrolet Cruze Owner Manual - 2012

Black plate (36,1)

5-36

Instruments and Controls

See “Rear Window Defogger” under Climate Control Systems on page 8‑1 for more information. Press the MENU or MENU/SEL knob when Auto Rear Defog is highlighted to open the menu. Turn the knob to highlight On or Off. Press the knob to confirm the selection and move back to the last menu. Comfort and Convenience Select the Comfort and Convenience menu and Chime Volume will be displayed.

Chime Volume This allows the selection of the chime volume level. Press the MENU or MENU/SEL knob when Chime Volume is highlighted. Turn the knob to select Normal or High. Press the BACK button to confirm and go back to the last menu.

Collision/Detection Systems If equipped, select the Collision/ Detection Systems menu and Park Assist will be displayed.

Park Assist This allows the Ultrasonic Parking Assist feature, audible only, to be turned on or off. Press the MENU or MENU/SEL knob when Park Assist is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu. Languages Select the Language menu and the following will be displayed: . English

Francais . Espanol Turn the MENU or MENU/SEL knob to select the language. Press BACK to return to the last menu.

Lighting Select the Lighting menu and the following will be displayed: . Exit Lighting . Vehicle Locator Lights

Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Press the MENU or MENU/SEL knob when Exit Lighting is highlighted. Turn the knob to select Off, 30 Seconds, 1 Minute, or 2 Minutes. Press the BACK button to confirm and go back to the last menu.

Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. When on, the headlamps and back‐up lamps will flash when K is pressed.

Chevrolet Cruze Owner Manual - 2012

Black plate (37,1)

Instruments and Controls

5-37

Press the MENU or MENU/SEL knob when Vehicle Locator Lights is highlighted to open the menu. Turn the MENU or MENU/SEL knob to highlight On or Off. Press MENU or MENU/SEL to select On or Off. Press the BACK button to confirm the selection and move back to the last menu. Power Door Locks Select Power Door Locks and the following will be displayed: . Auto Door Unlock . Delayed Door Lock . Unlocked Door Anti Lock Out . Auto Door Lock

Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park). Press the MENU or MENU/SEL knob when Auto Door Unlock is highlighted. Turn the knob to select

All Doors, Driver Door, or Off. Press the knob to confirm and go back to the last menu.

Delayed Door Lock When on, this feature will delay the locking of the doors until five seconds after the last door is closed. You will hear three chimes to signal delayed locking is in use. Press either the power lock button or Q on the RKE transmitter twice to override the delayed locking feature and immediately lock all of the doors. Press the MENU or MENU/SEL knob when Delayed Door Lock is highlighted to select On or Off. Press BACK to return to the last menu.

Unlocked Door Anti Lock Out When on, all doors will lock. The driver door will then unlock if door locking is requested while the driver door is open, and disable the Delayed Door Lock feature.

Even when this feature is off, the driver is protected from accidental lockouts when the key is in the ignition. If Off is selected, the Unlocked Door Anti Lock Out feature may be enabled through an additional menu selection. Press the MENU or MENU/SEL knob when Unlocked Door Anti Lock Out is highlighted to select On or Off. Press BACK to return to the last menu.

Auto Door Lock This allows selection of which of the doors will automatically lock when the vehicle is shifted into P (Park). Press the MENU or MENU/SEL knob when Auto Door Lock is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.

Chevrolet Cruze Owner Manual - 2012

Black plate (38,1)

5-38

Instruments and Controls

Remote Locking, Unlocking, Starting Select Remote Locking, Unlocking, Starting and the following will be displayed (depending on the system): . Remote Lock Feedback . Door Unlock or Remote Door

Unlock

. Remote Unlock Light Feedback . Remote Start

Remote Lock Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Press the MENU or MENU/SEL knob when Remote Lock Feedback is highlighted. Turn the knob to select Lights and Horn, Lights Only, Horn Only, or Off. Press the knob to confirm and go back to the last menu.

Door Unlock or Remote Door Unlock This allows selection of which doors will unlock when pressing K on the RKE transmitter. Press the MENU or MENU/SEL knob when Door Unlock is highlighted. Turn the knob to select All Doors or Driver Door Only. When set to Driver Door Only, the driver door will unlock the first time K is pressed and all doors will unlock when K is pressed a second time. When set to All Doors, all of the doors will unlock at the first press of K. Press the knob to confirm and go back to the last menu.

Remote Unlock Light Feedback If equipped, this allows selection of what type of feedback is given when unlocking the vehicle with the RKE transmitter. Press the MENU or MENU/SEL knob when Remote Unlock Light Feedback is highlighted.

Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.

Remote Start If equipped, this allows selection to turn on or off Remote Start. Press the MENU or MENU/SEL knob when Remote Start is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu. Return to Factory Settings Select Return to Factory Settings to return all vehicle personalization to the default settings. Turn the knob to select Yes or No. Press the knob to confirm and go back to the last menu.

Chevrolet Cruze Owner Manual - 2012

Black plate (1,1)

Lighting

Exterior Lighting

Exterior Lighting

Exterior Lamp Controls

Exterior Lamp Controls . . . . . . . . 6-1
Headlamp High/Low-Beam

Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running

Lamps (DRL) . . . . . . . . . . . . . . . . 6-2

Automatic Headlamp

System . . . . . . . . . . . . . . . . . . . . . . 6-3
Hazard Warning Flashers . . . . . 6-3
Turn and Lane-Change

Signals . . . . . . . . . . . . . . . . . . . . . . 6-4
Front Fog Lamps . . . . . . . . . . . . . . 6-4

Interior Lighting

Instrument Panel Illumination

Control . . . . . . . . . . . . . . . . . . . . . . 6-5
Courtesy Lamps . . . . . . . . . . . . . . 6-5
Dome Lamps . . . . . . . . . . . . . . . . . 6-5
Reading Lamps . . . . . . . . . . . . . . . 6-5

Lighting Features

Entry Lighting . . . . . . . . . . . . . . . . . 6-6
Exit Lighting . . . . . . . . . . . . . . . . . . . 6-6
Battery Power Protection . . . . . . 6-6

The exterior lamp control is located on the instrument panel to the outboard side of the steering column. It controls the following systems: . Headlamps

Taillamps

. Parking Lamps

License Plate Lamps Instrument Panel Lights Fog Lamps

Lighting

6-1

The exterior lamp control has four positions: O (Off): Briefly turn to this position to turn the automatic light control off or on again. AUTO (Automatic): Turns the headlamps on automatically at normal brightness, together with the following: . Parking Lamps

Taillamps License Plate Lamps Instrument Panel Lights

. Sidemarker Lamps ; (Parking Lamps): Turns the parking lamps on together with the following:

Taillamps License Plate Lamps Instrument Panel Lights

. Sidemarker Lamps

Chevrolet Cruze Owner Manual - 2012

Black plate (2,1)

6-2

Lighting

5 (Headlamps): Turns the headlamps on together with the lamps listed below. A warning chime sounds if the driver door is opened when the ignition switch is off and the headlamps are on. . Parking Lamps

Taillamps License Plate Lamps Instrument Panel Lights

. Sidemarker Lamps # (Front Fog Lamps): For vehicles with fog lamps, press to turn the lamps on or off. See Front Fog Lamps on page 6‑4. When the lights are on, ; will be lit. See Lamps On Reminder on page 5‑22.

Headlamp High/ Low-Beam Changer

2 3 Headlamp High/Low‐Beam Changer: Push the turn signal/lane change lever away from you to turn the high beams on. Pull the lever toward you to return to low beams.

Flash-to-Pass To flash the high beams, pull the turn signal/lane change lever all the way toward you. Then release it.

Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada.

This indicator light turns on in the instrument panel cluster when the high‐beam headlamps are on.

This indicator light turns on in the instrument panel cluster when the DRL are on. A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered.

Chevrolet Cruze Owner Manual - 2012

Black plate (3,1)

The DRL system makes the low‐beam headlamps come on at a reduced brightness when the following conditions are met: The ignition is in the ON/ RUN mode. The exterior lamps control is in AUTO. The engine is running.

When the DRL are on, only the low‐beam headlamps, at a reduced level of brightness, will be on. The taillamps, sidemarker, instrument panel, and other lamps will not be on. The headlamps automatically change from DRL to the regular headlamps depending on the darkness of the surroundings. The other lamps that come on with the headlamps will also come on. When it is bright enough outside, the headlamps go off and the DRL come on.

Lighting

6-3

or the headlamps will be on when they are not needed. The system may also turn on the headlamps when driving through a parking garage or tunnel.

Hazard Warning Flashers

To turn the DRL off or on again, turn the exterior lamps control to the off position and then release. For vehicles first sold in Canada, the DRL cannot be turned off.

Automatic Headlamp System When it is dark enough outside and the exterior lamps control is in the automatic position, the headlamps come on automatically. See Exterior Lamp Controls on page 6‑1.

The vehicle has a light sensor located on top of the instrument panel. Make sure it is not covered,

| (Hazard Warning Flasher): Press and momentarily hold this button located on the instrument panel above the climate control system, to make the front and rear turn signal lamps flash on and off.

Chevrolet Cruze Owner Manual - 2012

Black plate (4,1)

6-4

Lighting

This warns others that you are having trouble. Press and momentarily hold again to turn the flashers off.

Turn and Lane-Change Signals

The lever returns to its starting position when it is released. If after signaling a turn or lane change the arrow flashes rapidly or does not come on, a signal bulb may be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Fuses and Circuit Breakers on page 10‑35 for more information.

Front Fog Lamps

The ignition must be on to turn on the fog lamps. # : Press to turn the fog lamps on or off. An indicator light on the instrument panel cluster comes on when the fog lamps are on. The fog lamps come on together with the parking lamps. If the high‐beam headlamps are turned on, the fog lamps will turn off. If the high‐beam headlamps are turned off, the fog lamps will turn back on again. Some localities have laws that require the headlamps to be on along with the fog lamps.

An arrow on the instrument panel cluster will flash in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to flash to signal a lane change. The turn signal flashes three times.

For vehicles with front fog lamps, the button is located on the outboard side of the instrument panel.

Chevrolet Cruze Owner Manual - 2012

Black plate (5,1)

Interior Lighting

Instrument Panel Illumination Control

Courtesy Lamps The courtesy lamps come on automatically when any door is opened and the dome lamp is in the door position.

H (Door): Press to turn the lamps on automatically when a door is opened. ' (On): Press to turn on the dome lamps.

Dome Lamps

Reading Lamps

Lighting

6-5

This feature controls the brightness of the instrument panel controls and infotainment display screen. The thumbwheel is located to the left of the steering column on the instrument panel. D (Instrument Panel Brightness): Move the thumbwheel up or down and hold, to brighten or dim the instrument panel controls and infotainment display screen.

The dome lamp controls are located in the headliner. ( (Dome Lamp Override): Press to turn the lamps off, even when a door is open.

The reading lamps are located in the overhead console. # or $ : Press the button near each lamp to turn it on or off.

Chevrolet Cruze Owner Manual - 2012

Black plate (6,1)

6-6

Lighting

Lighting Features

Entry Lighting The headlamps, parking lamps, taillamps, and most of the interior lights turn on briefly, when the Remote Keyless Entry (RKE) K is pressed. After about 30 seconds the exterior lamps turn off, and then the dome and remaining interior lights will dim to off. Entry lighting can be disabled manually by changing the ignition out of the OFF position, or by pressing the RKE Q button. This feature can be changed. See Vehicle Personalization on page 5‑34.

Exit Lighting The headlamps, taillamps, parking lamps, back‐up lamps, and license plate lamps come on at night, or in areas with limited lighting, when the key is removed from the ignition. The dome lamps also come on when the key is removed from the ignition. The exterior lamps and dome lamps remain on after the door is closed for a set amount of time, then automatically turn off. The exterior lamps turn off immediately by turning the exterior lamps control off. The exit lighting feature can be changed. See Vehicle Personalization on page 5‑34.

Battery Power Protection The battery saver feature is designed to protect the vehicle's battery. If some interior lights are left on and the ignition is turned off, the battery rundown protection system automatically turns the lamp off after some time.

Chevrolet Cruze Owner Manual - 2012

Black plate (1,1)

Infotainment System 7-1

Audio Players

CD Player . . . . . . . . . . . . . . . . . . . 7-18
Auxiliary Devices . . . . . . . . . . . . 7-20

Phone

Bluetooth (Overview) . . . . . . . . 7-23
Bluetooth (Infotainment

Controls) . . . . . . . . . . . . . . . . . . . 7-25

Bluetooth (Voice

Recognition) . . . . . . . . . . . . . . . 7-29

Trademarks and License Agreements

Trademarks and License

Agreements . . . . . . . . . . . . . . . . 7-35

Infotainment System

Introduction

Infotainment . . . . . . . . . . . . . . . . . . . 7-2
Theft-Deterrent Feature . . . . . . . 7-2
Overview (Base Radio) . . . . . . . 7-3
Overview (Up-Level Radio) . . . 7-5
Operation . . . . . . . . . . . . . . . . . . . . . 7-6

Radio

AM-FM Radio . . . . . . . . . . . . . . . . 7-12
Satellite Radio . . . . . . . . . . . . . . . 7-14
Radio Reception . . . . . . . . . . . . . 7-17
Satellite Radio Antenna . . . . . . 7-18
Multi-Band Antenna . . . . . . . . . . 7-18

Chevrolet Cruze Owner Manual - 2012

Black plate (2,1)

Theft-Deterrent Feature The theft-deterrent feature works by learning a portion of the Vehicle Identification Number (VIN) to the infotainment system. The infotainment system does not