2012 Chevrolet Cruze Owners Manual

hydraulic system.

Checking Brake Fluid The brake/clutch fluid can be checked without taking off the cap by looking at the brake/clutch fluid reservoir. The fluid level should be above MIN. If it is not, have the brake/ clutch hydraulic system checked to see if there is a leak. After work is done on the brake/ clutch hydraulic system, make sure the level is above MIN but not over the MAX mark.

When the brake/clutch fluid falls to a low level, the brake warning light comes on. See Brake System Warning Light on page 5‑16.

What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 11‑13. Always clean the brake/clutch fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.

{ WARNING

With the wrong kind of fluid in the brake/clutch hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake/clutch fluid.

Chevrolet Cruze Owner Manual - 2012

Black plate (25,1)

Battery Refer to the replacement number on the original battery label when a new battery is needed.

{ WARNING

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Notice

. Using the wrong fluid can

badly damage brake/clutch hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid. If brake fluid is spilled on the vehicle's painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle. If you do, wash it off immediately.

Vehicle Care

10-25

Vehicle Storage

{ WARNING

Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 10‑80 for tips on working around a battery without getting hurt.

Infrequent Usage: Remove the black, negative (−) cable from the battery to keep the battery from running down. Extended Storage: Remove the black, negative (−) cable from the battery or use a battery trickle charger.

Chevrolet Cruze Owner Manual - 2012

Black plate (26,1)

10-26

Vehicle Care

Starter Switch Check

{ WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

1. Before starting this check, be

sure there is enough room around the vehicle.

2. Firmly apply both the parking brake and the regular brake. See Parking Brake on page 9‑36. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.

3. For automatic transmission

vehicles, try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service. For manual transmission vehicles, put the shift lever in Neutral, push the clutch pedal down halfway, and try to start the engine. The vehicle should start only when the clutch pedal is pushed down all the way to the floor. If the vehicle starts when the clutch pedal is not pushed all the way down, contact your dealer for service.

Automatic Transmission Shift Lock Control Function Check

{ WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

1. Before starting this check, be

sure there is enough room around the vehicle. It should be parked on a level surface.

Chevrolet Cruze Owner Manual - 2012

Black plate (27,1)

2. Firmly apply the parking brake.

See Parking Brake on page 9‑36. Be ready to apply the regular brake immediately if the vehicle begins to move.

3. With the engine off, turn the

ignition on, but do not start the engine. Without applying the regular brake, try to move the shift lever out of P (Park) with normal effort. If the shift lever moves out of P (Park), contact your dealer for service.

Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position.

For automatic transmission vehicles, the ignition should turn to LOCK/OFF only when the

shift lever is in P (Park). The ignition key should come out only in LOCK/OFF. For manual transmission vehicles, the ignition key should come out only in LOCK/OFF. Contact your dealer if service is required.

Park Brake and P (Park) Mechanism Check { WARNING

When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.

Vehicle Care

10-27

Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.

To check the parking brake's holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only. To check the P (Park) mechanism's holding ability: With the engine running, shift to P (Park). Then release the parking brake followed by the regular brake.

Contact your dealer if service is required.

Chevrolet Cruze Owner Manual - 2012

Black plate (28,1)

10-28

Vehicle Care

Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Maintenance Schedule on page 11‑3 for more information. Replacement blades come in different types and are removed in different ways. For proper windshield wiper blade length and type, see Maintenance Replacement Parts on page 11‑15. Notice: Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not be covered by your warranty. Do not allow the wiper blade arm to touch the windshield.

To replace the windshield wiper blade: 1. Pull the wiper assembly away

from the windshield.

4. Remove the wiper blade.

Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not be covered by the vehicle warranty. Do not allow the wiper blade to touch the windshield. 5. Reverse Steps 1 through 3 for

wiper blade replacement.

2. Lift up on the plastic latch in the middle of the wiper blade where the wiper arm attaches.

3. With the latch open, pull the wiper blade down toward the windshield far enough to release it from the J-hooked end of the wiper arm.

Chevrolet Cruze Owner Manual - 2012

Black plate (29,1)

Vehicle Care

10-29

High‐Beam Headlamp/ Low‐Beam Headlamp and DRL 1. Open the hood. See Hood on

page 10‑4.

Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However, if the vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if oncoming drivers flash their high-beam headlamps at you (for vertical aim). If the headlamps need to be re-aimed, it is recommended that the vehicle be taken to a dealer for service.

Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 10‑34. For any bulb‐changing procedure not listed in this section, contact your dealer.

Headlamps, Front Turn Signal and Parking Lamps

2. Remove the connector

retaining tab (A).

3. Disconnect the wiring harness connector from the bulb (C) by pressing the connector release (B) and pulling straight back.

A. Parking/Turn Signal Lamp B. High‐Beam Headlamp/

Low‐Beam Headlamp and DRL

Chevrolet Cruze Owner Manual - 2012

Black plate (30,1)

10-30

Vehicle Care

5.

4. Remove the bulb (C) from the headlamp assembly by turning counterclockwise and pulling straight back. Install the new bulb in the headlamp assembly by turning clockwise. Install the wiring harness connector to the bulb. Be sure the connector release (B) locks into place. Install the connector retaining tab (A).

6.

7.

Parking/Turn Signal Lamp 1. Open the hood. See Hood on

page 10‑4.

2. Remove the parking/turn signal

lamp bulb socket from the headlamp assembly by turning counterclockwise.

3. Remove the bulb (A) from the

4.

5.

bulb socket. Install the new bulb in the bulb socket. Install the bulb socket into the headlamp assembly by turning clockwise.

Chevrolet Cruze Owner Manual - 2012

Black plate (31,1)

Vehicle Care

10-31

Taillamps, Turn Signal, Sidemarker, Stoplamps, and Back-Up Lamps

Trunk Deck Inboard Taillamps 1. Open the trunk.

2. Remove the trunk deck trim

4. Remove the bulb from the

cover (A).

3. Remove the bulb socket (B) by

turning counterclockwise and pulling straight out.

socket (A). Install the new bulb in the bulb socket. Install the bulb socket by turning clockwise. Install the trunk deck trim cover.

5.

6.

7.

Chevrolet Cruze Owner Manual - 2012

Black plate (32,1)

10-32

Vehicle Care

To replace any one of these bulbs:

Stoplamp/Taillamp, Turn Signal, Back‐up, and Rear Sidemarker Lamp 1. Open the trunk.

A. Back-up Lamp B. Stoplamp/Taillamp C. Turn Signal Lamp D. Sidemarker Lamp

3. Remove the two screws, that secure the taillamp assembly.

2. Open the two screw covers.

Chevrolet Cruze Owner Manual - 2012

Black plate (33,1)

Vehicle Care

10-33

5. Remove the bulb socket from

the taillamp assembly by turning it counterclockwise. Install a new bulb into the bulb socket. Install the bulb socket into the taillamp assembly by turning it clockwise. Install the taillamp assembly and tighten the two screws.

6.

7.

8.

9. Close the two screw covers.

4. Remove the taillamp assembly by pulling it straight back until the two posts disengage from the grommets.

A. Sidemarker Lamp B. Turn Signal Lamp C. Stoplamp/Taillamp D. Back-up Lamp

Chevrolet Cruze Owner Manual - 2012

Black plate (34,1)

10-34

Vehicle Care

License Plate Lamp To replace the license plate lamp bulb:

1. Remove the two screws from the

license plate lamp assembly.

2. Turn and pull the license plate

lamp assembly down.

3. Turn the bulb socket

counterclockwise and pull the bulb straight out of the socket.

4. Push the new bulb into the

5.

socket. Install the bulb socket by turning clockwise into the license plate lamp assembly.

6. Replace the license plate lamp

assembly by using the two screws to secure.

Replacement Bulbs

Exterior Lamp

Back-Up Lamp Front and Rear Sidemarker Lamp Front Parking/Turn Signal Lamp High Beam/Low Beam and DRL Headlamp Rear Turn Signal Lamp Stoplamp/Taillamp

Bulb

Number

921K

194

7444NA

H13LL

7443NA

3057K LCP

For replacement bulbs not listed here, contact your dealer.

Chevrolet Cruze Owner Manual - 2012

Black plate (35,1)

Electrical System

Electrical System Overload The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the chance of circuit overload and fire caused by electrical problems. Fuses and circuit breakers protect power devices in the vehicle. Replace a bad fuse with a new one of the identical size and rating. If there is a problem on the road and a fuse needs to be replaced, the same amperage fuse can be borrowed. Choose some feature of the vehicle that is not needed to use and replace it as soon as possible.

Headlamp Wiring An electrical overload may cause the lamps to go on and off, or in some cases to remain off. Have the headlamp wiring checked right away if the lamps go on and off or remain off. Windshield Wipers If the wiper motor overheats due to heavy snow or ice, the windshield wipers will stop until the motor cools and will then restart. Although the circuit is protected from electrical overload, overload due to heavy snow or ice may cause wiper linkage damage. Always clear ice and heavy snow from the windshield before using the windshield wipers. If the overload is caused by an electrical problem and not snow or ice, be sure to get it fixed.

Vehicle Care

10-35

Fuses and Circuit Breakers The wiring circuits in the vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure to replace a bad fuse with a new one of the identical size and rating. Fuses of the same amperage can be temporarily borrowed from another fuse location, if a fuse goes out. Replace the fuse as soon as possible. To identify and check fuses, circuit breakers, and relays, see Engine Compartment Fuse Block on page 10‑36 and Instrument Panel Fuse Block on page 10‑40.

Chevrolet Cruze Owner Manual - 2012

Black plate (36,1)

10-36

Vehicle Care

Engine Compartment Fuse Block

To remove the fuse block cover, squeeze the clips and swing it up. Notice: Spilling liquid on any electrical component on the vehicle may damage it. Always keep the covers on any electrical component.

Engine Compartment Fuse Block

The vehicle may not be equipped with all of the fuses, relays, and features shown.

Mini Fuses

Usage Transmission Control Module Engine Control Module Not Used

Chevrolet Cruze Owner Manual - 2012

Black plate (37,1)

Mini Fuses

10

11

13

14
15

16

17

Usage Canister Vent Solenoid Ignition Not Used Fuel Injection Fuel Injection/ Ignition System Engine Control Module Lambda Sensor Canister Vent Solenoid Not Used Rear Wiper Ignition/Air Quality Sensor/Aero‐Shutter Ignition/Airbag

Vehicle Care

10-37

Mini Fuses

Usage

Mini Fuses

Usage

18
19
20
23
29

30

31

32

33

34

35

36

Fuel Control Module Not Used Fuel Pump Not Used Not Used Antilock Brake System Body Control Module Body Control Module Front Seat Heating Sunroof (If Equipped) Infotainment System/Amplifier Not Used

37

38
39
40
46
47
48
49
50
51
52

53

54

High Beam Right Side High Beam Left Side Not Used Not Used Cooling Fan Lambda Sensor Fog Lights Not Used Not Used Horn Ignition Automatic Dimming Rearview Mirror Light Switch/ Light Control

Chevrolet Cruze Owner Manual - 2012

Black plate (38,1)

10-38

Vehicle Care

Mini Fuses

55
56

57

58
60
61
62

63

64
65
66

Usage Mirror Folding Windshield Washer Steering Column Lock Not Used Heated Mirror Heated Mirror Air Conditioning Rear Window Sensor Air Quality Sensor Rear Fog Lamp Rear Washer

Mini Fuses

Usage

67

68

69

70
71

Fuel System Control Module Not Used Battery Voltage Sensor Not Used Not Used

J‐Case Fuses

12

21

Usage

Front Wipers Starter Solenoid Rear Power Windows

J‐Case Fuses

Usage

22

24

25

26

27

28

41
42

Not Used Front Power Windows Electronic Vacuum Pump Antilock Brake System Pump Electronic Key System/PEPS Rear Window Defogger Not Used Cooling Fan K2

Chevrolet Cruze Owner Manual - 2012

Black plate (39,1)

Vehicle Care

10-39

Usage

HC Relays

Usage

13

Cooling Fan K2
Cooling Fan K1

Mini Relays

Usage

15
16
17

Ignition 87 Main Ignition 15
Not Used Not Used

J‐Case Fuses

Usage

Micro Relays

43
44
45
59

Micro Relays

Not Used Not Used Cooling Fan K1
Not Used

Usage

A/C Clutch Starter Solenoid Front Wiper Speed

10
12
14

Front Wiper On Not Used Cooling Fan K3
Cooling Fan K3
Not Used

U‐Micro Relays

Usage

11

Cooling Fan K7
Fuel Pump Not Used

Chevrolet Cruze Owner Manual - 2012

Black plate (40,1)

10-40

Vehicle Care

Instrument Panel Fuse Block

The instrument panel fuse block is in the driver side of the instrument panel. To access the fuses: 1. Open the fuse block cover by

pulling out at the top.

2. Remove the lower edge of

the cover.

3. Remove the cover. To reinstall the cover, reverse the steps above.

Instrument Panel Fuse Block The vehicle may not be equipped with all of the fuses, relays, and features shown.

Fuses

Usage

10

Infotainment System/Hands‐free Phone Not Used Body Control Module Infotainment System Information Display/ Parking Assist Cigarette Lighter Power Outlet Body Control Module Body Control Module Body Control Module

Chevrolet Cruze Owner Manual - 2012

Black plate (41,1)

Fuses

Usage

Fuses

Usage

Relays

Usage

Vehicle Care

10-41

Trunk Open Logistics Module RAP Relay

11
12
13

14

15

16

17

18
19

Interior Fan Not Used Power Seat Diagnostic Connector Airbag Central Locking System/Tailgate Air Conditioning System Not Used Not Used

20
21

22

23

24

25

26

Not Used Instrument Cluster Ignition/Electronic Key System Body Control Module Body Control Module Steering Column Lock Not Used

Chevrolet Cruze Owner Manual - 2012

Black plate (42,1)

10-42

Vehicle Care

Wheels and Tires

Tires Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer.

{ WARNING . Poorly maintained and

improperly used tires are dangerous.

. Overloading the tires can

cause overheating as a result of too much flexing. There could be a blowout and a serious crash. See Vehicle Load Limits on page 9‑10.

(Continued)

WARNING (Continued)

WARNING (Continued)

. Underinflated tires pose the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when the tires are cold.

. Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when hitting a pothole. Keep tires at the recommended pressure.

. Worn or old tires can cause a

crash. If the tread is badly worn, replace them.

. Replace any tires that have been damaged by impacts with potholes, curbs, etc.

(Continued)

. Improperly repaired tires can

cause a crash. Only the dealer or an authorized tire service center should repair, replace, dismount, and mount the tires.

. Do not spin the tires in

excess of 55 km/h (35 mph) on slippery surfaces such as snow, mud, ice, etc. Excessive spinning may cause the tires to explode.

Winter Tires Consider installing winter tires on the vehicle if frequent driving on snow or ice covered roads is expected. All season tires provide good overall performance on most surfaces, but they may not offer the traction or the same level of performance as winter tires on snow or ice covered roads.

Chevrolet Cruze Owner Manual - 2012

Black plate (43,1)

Vehicle Care

10-43

Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y, and ZR speed rated tires. If winter tires with a lower speed rating are chosen, never exceed the tire's maximum speed capability.

Low-Profile Tires If the vehicle has P225/45R18
size tires, they are classified as low‐profile tires. These tires are designed for very responsive driving on wet or dry pavement, however, may produce more road noise and tend to wear faster.

Notice: Low‐profile tires are more susceptible to damage from road hazards or curb impact than standard profile tires. Tire and/or wheel assembly damage can occur when coming into contact with road hazards like, potholes, or sharp edged objects, or when sliding into a curb. The warranty does not cover this type of damage. Keep tires set to the correct inflation pressure and, when possible, avoid contact with curbs, potholes, and other road hazards.

Winter tires, in general, are designed for increased traction on snow and ice covered roads. With winter tires, there may be decreased dry road traction, increased road noise, and shorter tread life. After changing to winter tires, be alert for changes in vehicle handling and braking. See your dealer for details regarding winter tire availability and proper tire selection. Also, see Buying New Tires on page 10‑57. If using snow tires: . Use tires of the same brand and

tread type on all four wheel positions.

. Use only radial ply tires of the

same size, load range, and speed rating as the original equipment tires.

Chevrolet Cruze Owner Manual - 2012

Black plate (44,1)

10-44

Vehicle Care

Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples show a typical passenger vehicle tire and a compact spare tire sidewall.

Passenger (P‐Metric) Tire Example (A) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type,

and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. (C) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. (D) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code are the

Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 10‑59. (G) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.

Chevrolet Cruze Owner Manual - 2012

Black plate (45,1)

Vehicle Care

10-45

For more information on tire pressure and inflation see Tire Pressure on page 10‑49. (F) Tire Size: A combination of letters and numbers define a tire's width, height, aspect ratio, construction type, and service description. The letter T as the first character in the tire size means the tire is for temporary use only. (G) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.

compact spare tire, see Compact Spare Tire on page 10‑80 and If a Tire Goes Flat on page 10‑63. (C) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (D) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. (E) Tire Inflation: The temporary use tire or compact spare tire should be inflated to 420 kPa (60 psi).

Compact Spare Tire Example

(A) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (B) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 5 000 km (3,000 mi) and should not be driven at speeds over 105 km/h (65 mph). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat. If the vehicle has a

Chevrolet Cruze Owner Manual - 2012

Black plate (46,1)

10-46

Vehicle Care

Tire Designations

Tire Size The following is an example of a typical passenger vehicle tire size.

(A) Passenger (P‐Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width: The three‐digit number indicates the tire section width in millimeters from sidewall to sidewall.

(C) Aspect Ratio: A two‐digit number that indicates the tire height‐to‐width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted‐bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches. (F) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire

is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.

Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight: The combined weight of optional accessories. Some examples of optional accessories are automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width.

Chevrolet Cruze Owner Manual - 2012

Black plate (47,1)

Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in kPa (kilopascal) or psi (pounds per square inch) before a tire has built up heat from driving. See Tire Pressure on page 10‑49. Curb Weight: The weight of a motor vehicle with standard and optional equipment including the

maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR: Gross Vehicle Weight Rating. See Vehicle Load Limits on page 9‑10. GAWR FRT: Gross Axle Weight Rating for the front axle. See Vehicle Load Limits on page 9‑10.

Vehicle Care

10-47

GAWR RR: Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits on page 9‑10. Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT‐Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279
that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall.

Chevrolet Cruze Owner Manual - 2012

Black plate (48,1)

10-48

Vehicle Care

Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lbs). See Vehicle Load Limits on page 9‑10. Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears

manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure on page 10‑49
andVehicle Load Limits on page 9‑10. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread.

Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1.6 mm (1/16 in) of tread remains. See When It Is Time for New Tires on page 10‑57.

Chevrolet Cruze Owner Manual - 2012

Black plate (49,1)

UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire's traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 10‑59. Vehicle Capacity Weight: The number of designated seating positions multiplied by 68 kg (150 lbs) plus the rated cargo load. See Vehicle Load Limits on page 9‑10. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight.

Vehicle Placard: A label permanently attached to a vehicle showing the vehicle capacity weight and the original equipment tire size and recommended inflation pressure. See “Tire and Loading Information Label” under Vehicle Load Limits on page 9‑10.

Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:

. Tire overloading and

overheating which could lead to a blowout.

Vehicle Care

10-49

. Premature or

irregular wear. . Poor handling. . Reduced fuel economy.

Overinflated tires, or tires that have too much air, can result in:

. Unusual wear. . Poor handling. . Rough ride. . Needless damage from

road hazards.

The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures. The recommended pressure is the minimum air pressure needed to support the vehicle's maximum load carrying capacity.

Chevrolet Cruze Owner Manual - 2012

Black plate (50,1)

10-50

Vehicle Care

For additional information regarding how much weight the vehicle can carry, and an example of the Tire and Loading Information label, see Vehicle Load Limits on page 9‑10. How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.

When to Check Check the tires once a month or more. Do not forget the compact spare tire, if the vehicle has one. The compact spare should be at 420 kPa (60 psi). For additional information regarding the compact spare tire, see Compact Spare Tire on page 10‑80.

How to Check Use a good quality pocket-type gauge to check tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air.

Re‐check the tire pressure with the tire gauge. Return the valve caps on the valve stems to prevent leaks and keep out dirt and moisture.

Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or

Chevrolet Cruze Owner Manual - 2012

Black plate (51,1)

tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under‐inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under‐inflated tire causes the tire to overheat and can lead to tire failure. Under‐inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability.

Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under‐inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start‐ups as long as the malfunction exists.

Vehicle Care

10-51

When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation on page 10‑52 for additional information.

Chevrolet Cruze Owner Manual - 2012

Black plate (52,1)

10-52

Vehicle Care

Federal Communications Commission (FCC) Rules and with Industry Canada Standards See Radio Frequency Statement on page 13‑16 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and with Industry Canada Standards RSS-GEN/210/220/310.

Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmit the tire pressure readings to a receiver located in the vehicle.

details about the DIC operation and displays see Driver Information Center (DIC) on page 5‑23. The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and must be inflated to the proper pressure. A Tire and Loading Information label shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load Limits on page 9‑10, for an example of the Tire and Loading Information label and its location. Also see Tire Pressure on page 10‑49. The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection on page 10‑55, Tire Rotation on page 10‑55 and Tires on page 10‑42.

When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the Tire and Loading Information label. See Vehicle Load Limits on page 9‑10. A message to check the pressure in a specific tire displays in the Driver Information Center (DIC) display. The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed. For additional information and

Chevrolet Cruze Owner Manual - 2012

Black plate (53,1)

Notice: Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use only the GM-approved tire sealant available through your dealer or included in the vehicle. Factory-installed Tire Inflator Kits use a GM-approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See Tire Sealant and Compressor Kit on page 10‑65 for information regarding the inflator kit materials and instructions. TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on

for the remainder of the ignition cycle. A DIC warning message also displays. The malfunction light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause these to come on are: . One of the road tires has been

replaced with the spare tire. The spare tire does not have a TPMS sensor. The malfunction light and DIC message should go off after the road tire is replaced and the sensor matching process is performed successfully. See "TPMS Sensor Matching Process" later in this section. The TPMS sensor matching process was not done or not completed successfully after rotating the tires. The malfunction light and the DIC message should go off after successfully completing the

Vehicle Care

10-53

sensor matching process. See "TPMS Sensor Matching Process" later in this section.

. One or more TPMS sensors are

missing or damaged. The DIC message and the malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer for service.

. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended could prevent the TPMS from functioning properly. See Buying New Tires on page 10‑57.

. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.

If the TPMS is not functioning properly, it cannot detect or signal a low tire condition.

Chevrolet Cruze Owner Manual - 2012

Black plate (54,1)

10-54

Vehicle Care

See your dealer for service if the TPMS malfunction light and DIC message come on and stay on. TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the tires or replacing one or more of the TPMS sensors. The TPMS sensor matching process should also be performed after replacing a spare tire with a road tire containing the TPMS sensor. The malfunction light and the DIC message should go off at the next ignition cycle. The sensors are matched to the tire/ wheel positions, using a TPMS relearn tool, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear. See your dealer for service or to purchase a relearn tool.

There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. The TPMS sensor matching process is: 1. Set the parking brake. 2. Turn the ignition to ON/RUN with

the engine off.

3. Use the MENU button to select the Vehicle Information menu in the Driver Information Center (DIC).

4. Use the thumbwheel to scroll to

the Tire Pressure menu item screen.

5. Press the SET/CLR button to

begin the sensor matching process. A message requesting acceptance of the process should display.

6. Press the SET/CLR button again

to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen.

7. Start with the driver side

front tire.

8. Place the relearn tool against

the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.

9. Proceed to the passenger side

front tire, and repeat the procedure in Step 8.

10. Proceed to the passenger side

rear tire, and repeat the procedure in Step 8.

Chevrolet Cruze Owner Manual - 2012

Black plate (55,1)

11. Proceed to the driver side rear tire, and repeat the procedure in Step 8. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.

12. Turn the ignition to LOCK/OFF. 13. Set all four tires to the

recommended air pressure level as indicated on the Tire and Loading Information label.

Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month. Replace the tire if: . The indicators at three or

more places around the tire can be seen.

. There is cord or fabric

showing through the tire's rubber.

. The tread or sidewall is

cracked, cut, or snagged deep enough to show cord or fabric.

. The tire has a bump, bulge,

or split.

Vehicle Care

10-55

. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.

Tire Rotation Tires should be rotated every 12 000 km (7,500 mi). See Maintenance Schedule on page 11‑3. Tires are rotated to achieve a uniform wear for all tires. The first rotation is the most important. Any time unusual wear is noticed, rotate the tires as soon as possible and check the wheel alignment. Also check for damaged tires or wheels.

Chevrolet Cruze Owner Manual - 2012

Black plate (56,1)

10-56

Vehicle Care

See When It Is Time for New Tires on page 10‑57 and Wheel Replacement on page 10‑61.

Use this rotation pattern when rotating the tires. Do not include the compact spare tire in the tire rotation.

Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated. See Tire Pressure on page 10‑49 and Vehicle Load Limits on page 9‑10. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10‑52. Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 12‑2.

{ WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.

(Continued)

WARNING (Continued)

The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.

Chevrolet Cruze Owner Manual - 2012

Black plate (57,1)

When It Is Time for New Tires Factors such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.

Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. See Tire Inspection on page 10‑55 and Tire Rotation on page 10‑55 for more information.

The rubber in tires ages over time. This also applies for the spare tire, if the vehicle has one, even if it is never used. Multiple conditions including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. Tires will typically need to be replaced due to wear before they may need to be replaced due to age. Consult the tire manufacturer for more information on when tires should be replaced. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. This area should be free of grease, gasoline, or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for

Vehicle Care

10-57

at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.

Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating. GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance.