You may also be interested in...
Download PDF Manual

conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in kPa (kilopascal) or psi (pounds per square inch)


before a tire has built up heat from driving. See Tire Pressure on page 10-51. Curb Weight: The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR: Gross Vehicle Weight Rating. See Vehicle Load Limits on page 9-14.


Vehicle Care


10-49


GAWR FRT: Gross Axle Weight Rating for the front axle. See Vehicle Load Limits on page 9-14. GAWR RR: Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits on page 9-14. Intended Outboard Sidewall: The side of an asymmetrical tire that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279
that corresponds to the load carrying capacity of a tire.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (50,1)


10-50


Vehicle Care


Maximum Inflation Pressure: The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lb). See Vehicle Load Limits on page 9-14. Occupant Distribution: Designated seating positions.


Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure on page 10-51 and Vehicle Load Limits on page 9-14.


Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (51,1)


Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1.6 mm (1/16 in) of tread remains. See When It Is Time for New Tires on page 10-58. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire's traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 10-61.


Vehicle Capacity Weight: The number of designated seating positions multiplied by 68 kg (150 lb) plus the rated cargo load. See Vehicle Load Limits on page 9-14. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle capacity weight and the original equipment tire size and recommended inflation pressure. See “Tire and Loading Information Label” under Vehicle Load Limits on page 9-14.


Tire Pressure Tires need the correct amount of air pressure to operate effectively.


Vehicle Care


10-51


{ Caution


Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:


. Tire overloading and


overheating which could lead to a blowout.


. Premature or irregular wear. . Poor handling. . Reduced fuel economy.


Overinflated tires, or tires that have too much air, can result in:


. Unusual wear. . Poor handling. . Rough ride. . Needless damage from


road hazards.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (52,1)


10-52


Vehicle Care


The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures. The recommended pressure is the minimum air pressure needed to support the vehicle's maximum load carrying capacity. For additional information regarding how much weight the vehicle can carry, and an example of the Tire and Loading Information label, see Vehicle Load Limits on page 9-14. How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.


When to Check Check the tires once a month or more.


How to Check Use a good quality pocket-type gauge to check the tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get the pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure in high, press on the metal stem in the center


of the tire valve to release air. Re-check the tire pressure with the tire gauge. Return the valve caps on the valve stems to keep out dirt and moisture and prevent leaks.


Tire Pressure for High-Speed Operation


{ Warning


Driving at high speeds, 160 km/h (100 mph) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat buildup and can cause sudden tire failure. You could have a crash and you or others could be killed. Some high-speed rated tires require inflation pressure adjustment for high-speed operation. When speed limits and road conditions are such that a vehicle can be


(Continued)


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (53,1)


Warning (Continued)


driven at high speeds, make sure the tires are rated for high-speed operation, in excellent condition, and set to the correct cold tire inflation pressure for the vehicle load.


The tires require inflation pressure adjustment when driving the vehicle at speeds of 282 km/h (175 mph) or higher, where it is legal. Set the cold inflation pressure to the maximum inflation pressure shown on the tire sidewall, or 265 kPa (38 psi), whichever is lower. See the example following. Return the tires to the recommended cold tire inflation pressure when high-speed driving has ended. See Vehicle Load Limits on page 9-14. Example: The maximum load and inflation pressure molded on the tire sidewall, in small letters, near


the rim flange. It will read something like this: Maximum load 690 kg (1521 lbs) 300 kPa (44 psi) Max. Press. For this example, set the inflation pressure for high‐speed driving at 265 kPa (38 psi). Racing or other competitive driving may affect the warranty coverage of the vehicle. See the warranty booklet for more information.


Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the


Vehicle Care


10-53


vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (54,1)


10-54


Vehicle Care


Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.


When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation on page 10-54. See Radio Frequency Statement on page 13-15.


Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the


driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly on your vehicle. The TPMS sensors monitor the air pressure in the tires and transmits the tire pressure readings to a receiver located in the vehicle.


When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light, located in the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the tire loading information label. See Vehicle Load Limits on page 9-14.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (55,1)


A message to check the pressure in a specific tire displays in the Driver Information Center (DIC). The low tire pressure warning light and the DIC warning message appear at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed. For additional information and details about the DIC operation and displays see Driver Information Center (DIC) on page 5-24 and Tire Messages on page 5-41. The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and needs to be inflated to the proper pressure.


A Tire and Loading Information label shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load Limits on page 9-14, for an example of the Tire and Loading Information label and its location. Also see Tire Pressure on page 10-51 for additional information. The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection on page 10-56, Tire Rotation on page 10-57, When It Is Time for New Tires on page 10-58, and Tires on page 10-43.


{ Caution


Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire


(Continued)


Vehicle Care


10-55


Caution (Continued)


sealant is not covered by the vehicle warranty. Always use only the GM approved tire sealant available through your dealer or included in the vehicle.


Factory-installed Tire Inflator Kits use a GM approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See Tire Sealant and Compressor Kit on page 10-66 for information regarding the inflator kit materials and instructions. TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message also


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (56,1)


10-56


Vehicle Care


displays. The malfunction light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause these to come on are:


The TPMS sensor matching process was not done or not completed successfully. The malfunction light and the DIC message should go off after successfully completing the sensor matching process.


. One or more TPMS sensors are


missing or damaged. The malfunction light and the DIC message should go off when the TPMS sensors are installed and the sensor matching process is performed successfully.


. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended could prevent the TPMS from functioning properly. See Buying New Tires on page 10-59.


. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.


If the TPMS is not functioning properly, it cannot detect or signal a low tire condition. See your dealer for service if the TPMS malfunction light and DIC message come on and stays on. TPMS Sensor Matching Process — Auto Learn Function Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the tires or replacing one or more of the TPMS sensors. When a tire is installed, the vehicle must be stationary for about 20 minutes before the system recalculates. The following relearn process takes up to 10 minutes, driving at a minimum speed of 19 km/h (12 mph).


A dash (-) or pressure value will display in the DIC. See Driver Information Center (DIC) on page 5-24 and Tire Messages on page 5-41. A warning message displays in the DIC if a problem occurs during the relearn process.


Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month. Replace the tire if: . The indicators at three or


more places around the tire can be seen.


. There is cord or fabric


showing through the tire's rubber.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (57,1)


Anytime unusual wear is noticed, rotate the tires as soon as possible, check for proper tire inflation pressure, and check for damaged tires or wheels. If the unusual wear continues after the rotation, check the wheel alignment. See When It Is Time for New Tires on page 10-58
and Wheel Replacement on page 10-63. Different tire sizes should not be rotated front to rear.


. The tread or sidewall is


cracked, cut, or snagged deep enough to show cord or fabric.


. The tire has a bump, bulge,


or split.


. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.


Tire Rotation The tires should be rotated every 12 000 km/7,500 mi. See Maintenance Schedule on page 11-3. Tires are rotated to achieve uniform wear for all tires. The first rotation is the most important.


Vehicle Care


10-57


Use this rotation pattern if the vehicle has different size tires on the front and rear. Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated. See Tire Pressure on page 10-51
and Vehicle Load Limits on page 9-14. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10-54. Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 12-2.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (58,1)


10-58


Vehicle Care


{ Warning


Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.


Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.


When It Is Time for New Tires Factors such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.


Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. See Tire Inspection on page 10-56 and Tire Rotation on page 10-57.


The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple factors including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. GM recommends that tires, including the spare if equipped, be replaced after six years, regardless of tread wear. The tire manufacture date is the last four digits of the DOT Tire Identification Number (TIN) which is molded into one side of the tire sidewall. The first two digits represent the week (01–52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. This area should be free


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (59,1)


of grease, gasoline, or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.


Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating.


GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number will be followed by MS for mud and snow. See Tire Sidewall Labeling on page 10-46, for additional information. GM recommends replacing worn tires in complete sets of four. Uniform tread depth on all tires will help to maintain the performance of the vehicle.


Vehicle Care


10-59


Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. If proper rotation and maintenance have been done, all four tires should wear out at about the same time. See Tire Rotation on page 10-57 for information on proper tire rotation. However, if it is necessary to replace only one axle set of worn tires, place the new tires on the rear axle. Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, and ZR speed rated tires. Never exceed the winter tire's maximum speed capability when using winter tires with a lower speed rating.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (60,1)


10-60


Vehicle Care


{ Warning


{ Warning


Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death. Only your dealer or authorized tire service center should mount or dismount the tires.


{ Warning


Mixing tires of different sizes (other than those originally installed on the vehicle), brands, or types may cause loss of control of the vehicle, resulting in a crash or other vehicle damage. Use the correct size, brand, and type of tire on all four wheels.


Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving. A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.


If the vehicle tires must be replaced with a tire that does not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction (radial) as the original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed. See Tire Pressure Monitor Operation on page 10-54.


The Tire and Loading Information label indicates the original equipment tires on the vehicle. See Vehicle Load Limits on page 9-14, for the label location and more information about the Tire and Loading Information label.


Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, electronic stability control, or All-Wheel Drive, the performance of these systems can also be affected.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (61,1)


{ Warning


If different sized wheels are used, there may not be an acceptable level of performance and safety if tires not recommended for those wheels are selected. This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems developed for the vehicle, and have them properly installed by a GM certified technician.


See Buying New Tires on page 10-59 and Accessories and Modifications on page 10-2.


Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:


Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter tires, compact spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they


Vehicle Care


10-61


must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.


Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (62,1)


10-62


Vehicle Care


habits, service practices and differences in road characteristics and climate.


Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.


Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not


overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing are not necessary on a regular basis. Consider an alignment check if there is unusual tire wear. If the vehicle is vibrating when driving on a smooth road, the tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.


Road Imperfections/Crown Effects The vehicle's precise steering and handling make it very responsive to road surface feedback. A slight pull may be felt in the steering depending on the crown of the road


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (63,1)


and/or other road surface variations such as troughs or ruts. This is normal and the vehicle does not require service.


Tire Chatter/Hop When driving at slow speeds and in very tight turns, the vehicle may have tire chatter/hop. This is normal and the vehicle does not require service.


Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed.


Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. Replace wheels, wheel bolts, or wheel nuts with new GM original equipment parts.


{ Warning


Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.


Vehicle Care


10-63


{ Warning


Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.


{ Caution


The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire clearance to the body and chassis.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (64,1)


10-64


Vehicle Care


Tightening Wheel Lug Nuts


{ Warning


Never use oil or grease on studs or the threads of the wheel nuts. The wheel nuts might come loose and the wheel could fall off, causing a crash.


{ Warning


Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to a crash. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts.


{ Caution


Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification.


Tighten the wheel lug nuts firmly in a crisscross sequence. See Capacities and Specifications on page 12-2.


Tire Chains


{ Warning


Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause loss of control and a crash. Use another type of traction device only if its manufacturer recommends it for the vehicle's tire size combination and road conditions. Follow that manufacturer's instructions. To avoid vehicle damage, drive slowly and readjust or remove the traction device if it contacts the vehicle. Do not spin the wheels. If traction devices are used, install them on the rear tires.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (65,1)


If a Tire Goes Flat It is unusual for a tire to blow out while driving, especially if the tires are maintained properly. If air goes out of a tire, it is much more likely to leak out slowly. See Tires on page 10-43 for additional information. But if there ever is a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to


straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible. The vehicle has no spare tire, no tire changing equipment, and no place to store a tire. If the vehicle has run-flat tires, there is no need to stop on the side of the road to change a flat tire. See Run-Flat Tires on page 10-45.


{ Warning


Special tools and procedures are required to service a run-flat tire. If these special tools and procedures are not used, injury or vehicle damage may occur. Always be sure the proper tools and procedures, as described in the service manual, are used.


Vehicle Care


10-65


If this vehicle does not have run-flat tires and a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-4. 1. Turn on the hazard warning


flashers.


2. Set the parking brake firmly. 3. Put an automatic transmission in


P (Park) or a manual transmission in 1 (First) or R (Reverse).


4. Turn off the ignition. 5. Inspect the flat tire.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (66,1)


10-66


Vehicle Care


{ Warning


Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.


If this vehicle has a tire sealant kit and the tire has been separated from the wheel, has damaged sidewalls, or has a puncture larger than 6 mm (0.25 in), the tire is too severely damaged for the tire sealant and compressor kit to be effective. If the tire has a puncture less than 6 mm (0.25 in) in the tread area of the tire, see Tire Sealant and Compressor Kit on page 10-66.


Tire Sealant and Compressor Kit


{ Warning


Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 9-25.


{ Warning


Overinflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant (Continued)


Warning (Continued)


and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure.


{ Warning


Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (67,1)


The kit includes:


If this vehicle has a tire sealant and compressor kit, there may not be a spare tire or tire changing equipment, and on some vehicles there may not be a place to store a tire. To obtain a tire sealant and compressor kit, see your dealer. The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (0.25 in) in the tread area of the tire. It can also be used to inflate an underinflated tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program on page 13-5. Read and follow all of the tire sealant and compressor kit instructions.


Vehicle Care


10-67


1. Selector Switch (Sealant/Air


or Air Only)


2. On/Off Button 3. Pressure Gauge 4. Pressure Deflation Button 5. Tire Sealant Canister 6. Sealant/Air Hose (Clear) 7. Air Only Hose (Black) 8. Power Plug 9. Canister Release Button (Under Sealant/Air Hose)


Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer. See “Removal and Installation of the Sealant Canister” following.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (68,1)


10-68


Vehicle Care


There is only enough sealant to seal one tire. After usage, the sealant canister and sealant/air hose assembly must be replaced. See “Removal and Installation of the Sealant Canister” following. Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage.


3. Pressure Gauge 4. Pressure Deflation Button 5. Tire Sealant Canister 6. Sealant/Air Hose (Clear) 7. Air Only Hose (Black) 8. Power Plug 9. Canister Release Button (Under Sealant/Air Hose) When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-4. See If a Tire Goes Flat on page 10-65 for other important safety warnings.


1. Selector Switch (Sealant/Air


or Air Only)


2. On/Off Button


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (69,1)


Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and


compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10-74.


2. Unwrap the sealant/air hose (6)


and the power plug (8).


3. Place the kit on the ground.


Make sure the tire valve stem is positioned close to the ground so the hose will reach it.


4. Remove the valve stem cap from


the flat tire by turning it counterclockwise.


5. Attach the sealant/air hose (6) onto the tire valve stem. Turn it clockwise until it is tight.


6. Plug the power plug (8) into the


accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5-4. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.


7. Start the vehicle. The vehicle


must be running while using the air compressor.


8. Press and turn the selector


switch (1) counterclockwise to the Sealant + Air position.


9. Press the on/off button (2) to


turn the tire sealant and compressor kit on.


Vehicle Care


10-69


The compressor will inject sealant and air into the tire. The pressure gauge (3) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inflates with air only.


Inflate the tire to the recommended inflation pressure using the pressure gauge (3). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10-51.


10.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (70,1)


10-70


Vehicle Care


{ Caution


If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program on page 13-5.


11. Press the on/off button (2) to


turn the tire sealant and compressor kit off.


The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire, therefore, Steps 12–18 must be done immediately after Step 11. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.


12. Unplug the power plug (8) from


the accessory power outlet in the vehicle.


13. Turn the sealant/air hose (6)


counterclockwise to remove it from the tire valve stem.


14. Replace the tire valve


stem cap.


15. Replace the sealant/air hose


(6), and the power plug (8) back in their original location.


16.


If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister (5) and place it in a highly visible location. Do not exceed the speed on this label until the damaged tire is repaired or replaced.


17. Return the equipment to its


18.


original storage location in the vehicle. Immediately drive the vehicle 8 km (5 mi) to distribute the sealant in the tire.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (71,1)


Vehicle Care


10-71


19. Stop at a safe location and


check the tire pressure. Refer to Steps 1–11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured).” If the tire pressure has fallen more than 68 kPa (10 psi) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program on page 13-5. If the tire pressure has not dropped more than 68 kPa (10 psi) from the recommended inflation pressure, inflate the tire to the recommended inflation pressure.


20. Wipe off any sealant from the


wheel, tire, and vehicle.


21. Dispose of the used sealant canister (5) and sealant/air hose (6) assembly at a local dealer or in accordance with local state codes and practices.


22. Replace with a new canister assembly available from your dealer.


23. After temporarily sealing the tire using the tire sealant and compressor kit, take the vehicle to an authorized dealer within 161 km (100 mi) of driving to have the tire repaired or replaced.


Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant:


1. Selector Switch (Sealant/Air


or Air Only)


2. On/Off Button


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (72,1)


10-72


Vehicle Care


3. Pressure Gauge 4. Pressure Deflation Button 5. Tire Sealant Canister 6. Sealant/Air Hose (Clear) 7. Air Only Hose (Black) 8. Power Plug 9. Canister Release Button (Under Sealant/Air Hose)


If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-4. See If a Tire Goes Flat on page 10-65 for other important safety warnings. 1. Remove the tire sealant and


compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10-74.


2. Unwrap the air only hose (7) and


the power plug (8).


3. Place the kit on the ground.


Make sure the tire valve stem is positioned close to the ground so the hose will reach it.


8. Press and turn the selector


switch (1) clockwise to the Air Only position.


4. Remove the tire valve stem cap


9. Press the on/off button (2) to


from the flat tire by turning it counterclockwise.


5. Attach the air only hose (7) onto


the tire valve stem by turning it clockwise until it is tight.


6. Plug the power plug (8) into the


10.


accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5-4. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.


7. Start the vehicle. The vehicle


must be running while using the air compressor.


turn the compressor on. The compressor will inflate the tire with air only.


Inflate the tire to the recommended inflation pressure using the pressure gauge (3). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10-51. The pressure gauge (3) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate reading. The compressor may be turned on/ off until the correct pressure is reached.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (73,1)


If you inflate the tire higher than the recommended pressure you can adjust the excess pressure by pressing the pressure deflation button (4) until the proper pressure reading is reached. This option is only functional when using the air only hose (7).


11. Press the on/off button (2) to


turn the tire sealant and compressor kit off. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.


12. Unplug the power plug (8) from


the accessory power outlet in the vehicle.


13. Disconnect the air only hose


(7) from the tire valve stem, by turning it counterclockwise, and replace the tire valve stem cap.


14. Replace the air only hose (7)


and the power plug (8) and cord back in its original location.


15. Place the equipment in the


original storage location in the vehicle.


Vehicle Care


10-73


Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Unwrap the sealant hose. 2. Press the canister release


button (9).


3. Pull up and remove the canister. 4. Replace with a new canister which is available from your dealer.


5. Push the new canister into


place.


The tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inflate air mattresses, balls, etc.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (74,1)


10-74


Vehicle Care


Storing the Tire Sealant and Compressor Kit The tire sealant and compressor kit, if equipped, should be stored in the storage area behind the left rear wheel opening in the rear compartment when it is not being used. To access the storage area: 1. Open the hatch/trunk. See Hatch


(Trunk) on page 2-14.


2. Lift the storage cover.


{ Caution


Ignoring these steps could result in costly damage to the vehicle that would not be covered by the vehicle warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle.


The battery is under a battery cover in the hatch/trunk area on the passenger side under the carpet. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) terminal. Negative (−) will go the negative (−) terminal.


Jump Starting For more information about the vehicle battery, see Battery on page 10-30. If the battery has run down, use another vehicle and some jumper cables to start the vehicle. Be sure to use the following steps to do it safely.


{ Warning


Batteries can hurt you. They can be dangerous because:


. They contain acid that can


burn you.


. They contain gas that can


explode or ignite.


. They contain enough electricity to burn you.


If you do not follow these steps exactly, some or all of these things can hurt you.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (75,1)


{ Caution


If the other vehicle does not have a 12-volt system with a negative ground, both vehicles can be damaged. Only use a vehicle that has a 12-volt system with a negative ground for jump starting.


2. Get the vehicles close enough


so the jumper cables can reach, but be sure the vehicles are not touching each other. If they are, it could cause a ground connection you do not want. You would not be able to start the vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake firmly on both vehicles involved in the jump start procedure. Put an automatic transmission in P (Park) or a


Vehicle Care


10-75


manual transmission in Neutral before setting the parking brakes.


{ Caution


If any accessories are left on or plugged in during the jump starting procedure, they could be damaged. The repairs would not be covered by the vehicle warranty. Whenever possible, turn off or unplug all accessories on either vehicle when jump starting.


3. Turn off the ignition on both


vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlet. Turn off the radio and all lamps that are not needed. This will avoid sparks and help save both batteries. And it could save the radio!


1. Discharged Battery Positive (+)


Terminal


2. Discharged Battery Negative (−)


Terminal


3. Good Battery Negative (−)


Terminal


4. Good Battery Positive (+)


Terminal


1. Check the other vehicle. It must


have a 12-volt battery with a negative ground system.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (76,1)


10-76


Vehicle Care


8. Do not let the other end touch


metal. Connect it to the positive (+) terminal (4) of the good battery.


9. Now connect the black negative


(−) cable to the negative (−) terminal (3) of the good battery. Do not let the other end touch anything until the next step.


10. Connect the other end of the


negative (−) cable to the negative (−) terminal (2) on the dead battery.


11. Now start the vehicle with the


good battery and run the engine for a while.


12. Try to start the vehicle that had


the dead battery. If it will not start after a few tries, it probably needs service.


4. Open the rear hatch and lift the carpet on the passenger side of the vehicle to gain access to the battery cover.


5. Remove the battery cover and


locate the positive (+) and negative (−) terminals.


6. Check that the jumper cables do


not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too.


7. Open the positive terminal trim


cover and connect the red positive (+) cable to the positive (+) terminal (1) of the dead battery.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (77,1)


{ Caution If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.


Jumper Cable Removal Reverse the sequence exactly when removing the jumper cables. The power windows may need to be initialized. See “Window Indexing” under Power Windows on page 2-22.


Towing the Vehicle


{ Caution


Incorrectly towing a disabled vehicle may cause damage. The damage would not be covered by the vehicle warranty. Do not lash or hook to any suspension components — including the control arms, stabilizer bars, and links — during towing and recovery of a disabled vehicle, or when securing the vehicle to a flatbed car carrier. For towing and recovery of a disabled vehicle, use the proper hooks in the correct locations on the front and rear sub-frames. Use the proper nylon strap harnesses around the tires to secure them to the flatbed car carrier.


Have the vehicle towed on a flatbed car carrier. A wheel lift tow truck could damage the vehicle.


Vehicle Care


10-77


Consult your dealer or a professional towing service if the disabled vehicle must be towed. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motor home, see “Recreational Vehicle Towing” following.


Recreational Vehicle Towing


{ Caution


Dolly towing or dinghy towing the vehicle may cause damage because of reduced ground clearance. Always put the vehicle on a flatbed truck or trailer.


The vehicle was neither designed nor intended to be towed with any of its wheels on the ground. If the vehicle must be towed, see Towing the Vehicle on page 10-77.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (78,1)


10-78


Vehicle Care


Appearance Care


Exterior Care


Locks Locks are lubricated at the factory. Use a de-icing agent only when absolutely necessary, and have the locks greased after using. See Recommended Fluids and Lubricants on page 11-12. Washing the Vehicle To preserve the vehicle's finish, wash it often and out of direct sunlight.


{ Caution


Do not use petroleum-based, acidic, or abrasive cleaning agents as they can damage the vehicle's paint, metal, or plastic parts. If damage occurs, it would not be covered by the vehicle warranty. Approved cleaning


(Continued)


Caution (Continued)


products can be obtained from your dealer. Follow all manufacturer directions regarding correct product usage, necessary safety precautions, and appropriate disposal of any vehicle care product.


{ Caution Avoid using high-pressure washes closer than 30 cm (12 in) to the surface of the vehicle. Use of power washers exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals.


The e symbol is on any underhood compartment electrical center that should not be power


washed. This could cause damage that would not be covered by the vehicle warranty. If using an automatic car wash, comply with the car wash instructions. The windshield wiper must be off. Remove any accessories that may be damaged or interfere with the car wash equipment. Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. Finish Care Application of aftermarket clearcoat sealant/wax materials is not recommended. If painted surfaces are damaged, see your dealer to have the damage assessed and repaired. Foreign materials such as


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (79,1)


calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Occasional hand waxing or mild polishing should be done to remove residue from the paint finish. See your dealer for approved cleaning products. Do not apply waxes or polishes to uncoated plastic, vinyl, rubber, decals, simulated wood, or flat paint as damage can occur.


{ Caution Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle.


To keep the paint finish looking new, keep the vehicle garaged or covered whenever possible.


Protecting Exterior Bright Metal Moldings


{ Caution


Failure to clean and protect the bright metal moldings can result in a hazy white finish or pitting. This damage would not be covered by the vehicle warranty.


Vehicle Care


10-79


The bright metal moldings on the vehicle are aluminum. To prevent damage always follow these cleaning instructions: . Be sure the molding is cool to the touch before applying any cleaning solution.


. Use a cleaning solution


approved for aluminum. Some cleaners are highly acidic or contain alkaline substances and can damage the moldings.


. Always dilute a concentrated


cleaner according to the manufacturer’s instructions. . Do not use chrome cleaners. . Do not use cleaners that are not


intended for automotive use.


. Use a nonabrasive wax on the vehicle after washing to protect and extend the molding finish.


Chevrolet Corvette Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6007198) - 2014 - CRC - 2/5/14


Black plate (80,1)


10-80


Vehicle Care


Convertible Top Care Frequently hand wash convertible tops with mild car wash soap. Never use a stiff brush, steam, bleach, or aggressive cleaners. If necessary, a soft brush can be used to remove dirt. When finished cleaning, thoroughly rinse the fabric. Avoid automatic car washes with overhead brushes or very high-pressure sprays as they can cause damage and leaking. Only lower the top when it is completely dry and avoid leaving the top lowered for extended periods of time to prevent excessive interior weathering. Avoid leaving large amounts of snow on the top for extended periods of time as damage may also occur.

Loading...
x