2009 Chevrolet Corvette Owners Manual

(cid:129) Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by the vehicle warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid.

Outlet Adjustment Use the tab located on the air outlets to change the direction of the airflow. Operation Tips (cid:129) Clear away any ice, snow or leaves from the air

inlets at the base of the windshield that may block the flow of air into your vehicle.

(cid:129) Use of non-GM approved hood deflectors may adversely affect the performance of the system. (cid:129) Keep the area around the base of the instrument panel console and air path under the seats clear of objects to help circulate the air inside of your vehicle more effectively.

Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. The rear window defogger only works when the engine is running. = (Rear Window Defogger): Press to turn the rear window defogger on or off. Be sure to clear as much snow from the rear window as possible. An indicator light comes on to show that the rear window defogger is on. The rear window defogger turns off about 10 minutes after the button is pressed when traveling less than 30 mph (48 km/h). If turned on again, the defogger only runs for about five minutes before turning off. The defogger can also be turned off by turning off the engine. The vehicle has heated outside rearview mirrors. The mirrors will heat to help clear fog or frost from the surface of the mirrors when the rear window defogger button is pressed. For vehicles with a power convertible top, the rear window defogger and heated mirrors are automatically disabled when the power convertible top is moving or down.

3-30

Passenger Compartment Air Filter The passenger compartment air filter removes certain particles from the air including pollen and dust particles. Reductions in airflow, which may occur more often in dusty areas, indicate that the filter may need to be replaced. See Scheduled Maintenance on page 6-4
for information on how often to replace the filter. Notice: Driving without a passenger compartment air filter in place can cause water and small particles, like paper and leaves, to be pulled into your climate control system which may cause damage to it. Make sure you always replace the old filter with a new one. The passenger compartment air filter is located on the passenger side of the engine compartment near the battery. See Engine Compartment Overview on page 5-14.

To check or replace the air filter:

1. Remove the cover retainer clips (A) from the

passenger compartment air filter cover.

2. Remove the cover.

3-31

Warning Lights, Gages, and Indicators Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gages could prevent injury. Warning lights come on when there may be or is a problem with one of the vehicle’s functions. Some warning lights come on briefly when the engine is started to indicate they are working. Gages can indicate when there may be or is a problem with one of the vehicle’s functions. Often gages and warning lights work together to indicate a problem with the vehicle. When one of the warning lights comes on and stays on while driving, or when one of the gages shows there may be a problem, check the section that explains what to do. Follow this manual’s advice. Waiting to do repairs can be costly and even dangerous.

3. Remove the filter and install the new air filter. 4. Replace the filter cover. 5. Attach the retainer clips.

3-32

Instrument Panel Cluster The instrument panel cluster and Driver Information Center (DIC) are designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel the vehicle has left and many other things needed to know to drive safely and economically.

United States Manual Transmission shown, Canada, Automatic Transmission and Z06 Model similar

3-33

ZR1– United States shown Canada similar

3-34

Speedometer and Odometer The speedometer shows the speed in either miles per hour (mph) or kilometers per hour (km/h). For more information see “Personal Options” under DIC Vehicle Personalization on page 3-73. To read the odometer with the ignition off, turn on the parking lamps. If the vehicle needs a new odometer installed, the mileage total of the new odometer will be set to the original miles (kilometers) of the old odometer. See your dealer/retailer if the odometer must be replaced in the vehicle.

Tachometer The tachometer displays the engine speed in thousands of revolutions per minute (rpm). Notice: Fuel shuts off at about 6500 rpm for the base model, 7000 rpm for the Z06 model, and 6600 rpm for the ZR1 model. If the vehicle continues to be driven at the fuel shut off rpm, the engine could be damaged. Be sure to operate the vehicle below the fuel shut off rpm or reduce the vehicle’s rpm quickly when the fuel shuts off.

Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime comes on for several seconds to remind people to fasten their safety belts, unless the driver safety belt is already buckled.

The safety belt light also comes on and stay on for several seconds, then it flashes for several more.

This chime and light is repeated if the driver remains unbuckled and the vehicle is in motion. If the driver safety belt is already buckled, neither the chime nor the light comes on.

3-35

Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-44.

The airbag readiness light flashes for a few seconds when the engine is started. If the light does not come on then, have it fixed immediately.

{ CAUTION:

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message can also come on. See DIC Warnings and Messages on page 3-56
for more information.

3-36

Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-51 for important safety information. The rearview mirror has a passenger airbag status indicator.

United States

Canada

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol, to let you know the status to let you know the status of the right front passenger frontal and seat-mounted side impact airbags (if equipped). If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped) are enabled (may inflate). If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped). See Passenger Sensing System on page 1-51 for more on this, including important safety information.

3-37

If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service.

Voltmeter Gage

The voltmeter shows the voltage output of the battery. It shows the voltage output of the charging system while the engine is running.

Base and Z06

The reading changes as the rate of charge changes (with engine speed, for example), but if the voltmeter reads at 9 volts or below, the instrument panel cluster and other systems may shut down. The Driver Information Center (DIC) reads BATTERY VOLTAGE LOW when the vehicle is at 10 volts or below. Have it checked right away. Driving with the voltmeter reading at 10 volts or below could drain the battery and disable the vehicle.

{ CAUTION:

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 3-36
for more information, including important safety information.

3-38

One-to-Four Shift Light (Manual Transmission)

When this light comes on, the vehicle can only be shifted from 1 (First) to 4 (Fourth) instead of 1 (First) to 2 (Second).

The shift must be completed into 4 (Fourth) to turn off this feature. This helps the vehicle get the best possible fuel economy.

After shifting to 4 (Fourth), the vehicle can be downshifted to a lower gear. Notice: Forcing the shift lever into any gear except 4 (Fourth) when the 1 TO 4 SHIFT light comes on may damage the transmission. Shift only from 1 (First) to 4 (Fourth) when the light comes on. This light comes on when:

The engine coolant temperature is higher than 169°F (76°C), The vehicle is going 15 to 19 mph (24 to 31 km/h) and The vehicle 21 percent throttle or less.

3-39

(cid:129) (cid:129) (cid:129) Brake System Warning Light The vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working well.

United States

Canada

This light comes on briefly while starting the engine. If it does not come on, have it fixed so it is ready to warn if there is a problem.

{ CAUTION:

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

If this warning light stays on after the engine is started, the parking brake may still be set or there could be a brake problem. Refer to Parking Brake on page 2-32
to see if it is set. If the parking brake is not set, have the brake system inspected right away. If the light comes on while driving and a CHECK BRAKE FLUID message shows on the DIC, pull off the road and stop carefully. The pedal may be harder to push or the pedal may go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-28 and DIC Warnings and Messages on page 3-56 for more information.

3-40

Antilock Brake System (ABS) Warning Light

Traction Control System (TCS) Warning Light

For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started.

The Traction Control System (TCS) Warning light comes on briefly while starting the engine.

If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 3-40. For vehicles with a Driver Information Center (DIC), see DIC Warnings and Messages on page 3-56 for all brake related DIC messages.

If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. If the light stays on, or comes on while driving and a SERVICE TRACTION SYSTEM message displays in the Driver Information Center (DIC), the vehicle needs service. This light comes on when the TCS is turned off and a TRACTION SYSTEM OFF message displays on the DIC. When this light is on, the TCS system does not limit wheel spin.

3-41

This light turns off when the TCS is turned back on and a TRACTION SYSTEM ON message displays on the DIC See Traction Control System (TCS) on page 4-6 and DIC Warnings and Messages on page 3-56 for more information. This light also comes on while the vehicle is in the Competitive Mode. See Active Handling System on page 4-7. Active Handling System Light

The Active Handling System light comes on briefly as the engine is started. If the light does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the light goes off.

If the light stays on or comes on while driving, a chime sounds and a SERVICE ACTIVE HANDLING SYSTEM message appears on the DIC and the vehicle need service. The system is not working properly and the vehicle needs service. This light also comes on when the Competitive Drive mode is selected. When the Active Handling System is turned off, the light comes on, a chime sounds, and the TRACTION SYSTEM AND ACTIVE HANDLING – OFF message displays in the DIC. The Traction Control System is off and the Active Handling System does not assist with controlling the vehicle. When the Active Handling System is turned back on, the light turns off, a chime sounds and the TRACTION SYSTEM AND ACTIVE HANDLING – ON message displays in the DIC. See DIC Warnings and Messages on page 3-56 for more information.

3-42

Engine Coolant Temperature Gage

Tire Pressure Light

For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started.

United States

Canada

This gage shows the engine coolant temperature. If the gage pointer moves into the shaded area, the engine is too hot. This means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle and turn off the engine as soon as possible. See Engine Overheating on page 5-39 for more information.

It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is significantly underinflated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See DIC Warnings and Messages on page 3-56 for more information. Stop and check the tires as soon as it is safe to do so. If a tire is underinflated, inflate to the proper pressure. See Tires on page 5-62
for more information.

3-43

When the Light Flashes First and Then is On Steady This indicates that there could be a problem with the Tire Pressure Monitor System. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor System on page 5-73
for more information.

Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.

This comes on briefly while starting the engine. If it does not come on, have the vehicle serviced by your dealer/retailer.

If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle’s emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 5-3.

3-44

This light comes on during a malfunction in one of two ways:

Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required.

The following can prevent more serious damage to the vehicle: (cid:129) Reduce vehicle speed. (cid:129) Avoid hard accelerations. (cid:129) Avoid steep uphill grades. If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer/retailer for service as soon as possible.

Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required.

An emission system malfunction might be corrected by doing the following: (cid:129) Make sure the fuel cap is fully installed. See Filling

the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. If the vehicle has been driven through a deep puddle of water, the vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off.

(cid:129) Make sure to fuel the vehicle with quality fuel. Poor

fuel quality causes the engine not to run as efficiently as designed and may cause: stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Gasoline Octane on page 5-5.

3-45

(cid:129) If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection:

The vehicle will not pass this inspection if the check engine light is on with the engine running. To perform a check engine light bulb check with the keyless ignition, make sure the transmitter fob is in the passenger compartment. See Ignition Positions on page 2-23. Press the bottom of the Acc. button on the instrument panel and hold the button down

for five seconds. The instrument panel, including the check engine light, will light up and the ignition will be on, but the engine will not start — press the bottom of the Acc. button only briefly, less than five seconds, the accessory power mode will be turned on, but not the ignition. After the bulb check, press and release the Acc. button again to turn the ignition off and avoid draining the vehicle’s battery. The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if the battery has recently been replaced or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer/retailer can prepare the vehicle for inspection.

3-46

(cid:129) (cid:129) Engine Oil Pressure Gage

United States

Canada

United States — Z06

and ZR1 Models

Canada — Z06 and

ZR1 Models

{ CAUTION:

Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.

Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil. The engine oil pressure gage shows the engine oil pressure in psi (pounds per square inch) or kPa (kilopascals) when the engine is running. Oil pressure should be 20 to 80 psi (140 to 550 kPa). In certain situations such as long, extended idles on hot days, it could read as low as 6 psi (40 kPa) and still be considered normal. It may vary with engine speed, outside temperature and oil viscosity, but readings above the shaded area show the normal operating range. Readings in the shaded area tell you that the engine is low on oil, or that you might have some other oil problem. See Engine Oil on page 5-19. The engine oil pressure can also be displayed using the GAGES button on the Driver Information Center (DIC). See Driver Information Center (DIC) on page 3-50.

3-47

Security Light

Lights On Reminder

For information regarding this light and the vehicle’s security system, see Theft-Deterrent System on page 2-18.

This light comes on whenever the parking lamps are on.

Fog Lamp Light

The fog lamp light comes on when the fog lamps are in use.

See Headlamps on Reminder on page 3-15 for more information. Highbeam On Light

This light comes on when the high-beam headlamps are in use.

The light goes out when the fog lamps are turned off. See Fog Lamps on page 3-17 for more information.

See Headlamp High/Low-Beam Changer on page 3-8
for more information.

3-48

Fuel Gage

The fuel gage shows how much fuel the vehicle has left while the engine is on.

An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. When the needle approaches the low fuel symbol, a chime sounds and LOW FUEL appears on the Driver Information Center (DIC) display. There is still a little fuel left, but the vehicle’s fuel tank should be filled soon. Press the RESET button to acknowledge a DIC message(s). Pressing the RESET button also turns off a DIC message but the LOW FUEL message comes on again in 10 minutes if fuel is not added to the vehicle.

Here are five things that some owners ask about. All these things are normal and do not indicate that anything is wrong with the fuel gage. (cid:129) At the service station, the gas pump shuts off

before the gage reads the full. It takes a little more or less fuel to fill up than the gage indicated. For example, the gage may have indicated half full, but it took a little more or less than half of the tank’s capacity to fill the tank. The gage pointer may move while cornering, braking or speeding up. The gage may not indicate the tank is empty when the ignition is turned off. The gage reading may change slightly within the first several minutes after starting the vehicle.

See DIC Operation and Displays on page 3-50 for more information.

3-49

(cid:129) (cid:129) (cid:129) (cid:129) Boost Gage (ZR1 Only)

United States

Canada

For vehicles that have this gage, it is located near the driver side of the instrument panel cluster. This gage indicates vacuum during light to moderate throttle and boost under heavier throttle. It displays the air pressure level in the intake manifold before it enters the engine’s combustion chamber. The gage is automatically centered at zero every time the engine is started. Actual vacuum or boost is displayed from this zero point. Changes in ambient pressure, such as driving in mountains and changing weather, will slightly change the zero reading.

3-50

Driver Information Center (DIC) The Driver Information Center (DIC) display is located on the instrument panel cluster and shows driver personalization features and warning/status messages. The DIC buttons are located on the instrument panel, to the right of the cluster. The DIC comes on when the ignition is turned on. After displaying CORVETTE BY CHEVROLET, the DIC shows the information that was last displayed before the engine was turned off. If a problem is detected, a warning message appears on the DIC display. See DIC Warnings and Messages on page 3-56 for more information.

DIC Operation and Displays Depending on the features on the vehicle, the drive gear may display on the DIC. See “Manual Paddle Shift” under Automatic Transmission Operation on page 2-26
and “Head-Up Display (HUD)” in the index of the Navigation system manual for more information. The Driver Information Center (DIC) has different modes which can be accessed by pressing the following buttons located on the instrument panel, to the right of the instrument panel cluster.

2 (Gages): Press this button to display gage information like oil pressure and temperature, coolant temperature, automatic transmission fluid temperature, if equipped, battery voltage, and front/rear tire pressures.

TRIP: Press this button to display your total and trip distance driven, the elapsed time function, your average speed, and the engine oil life.

OPTION: Press this button to choose personal options that are available on your vehicle, depending on the options your vehicle is equipped with, such as door locks, easy entry seats, and language.

RESET: Press this button, used along with the other buttons, to reset system functions, select personal options, and turn off or acknowledge messages on the DIC.

3-51

. 4 (Fuel): Press this button to display fuel information such as fuel economy and range.

Fuel Range: The range calculates the remaining distance you can drive without refueling. It is based on fuel economy and the fuel remaining in the tank. Press the fuel button again to display the range, such as: (cid:129) RANGE 30 MI or (cid:129) RANGE 48 km If the LOW FUEL warning is displayed or if RANGE is less than 40 miles (64 km), the display will read RANGE LOW. The fuel economy data used to determine fuel range is an average of recent driving conditions. As your driving conditions change, this data is gradually updated automatically. If the vehicle has been idling for a long time, the range displayed on the DIC could be abnormally low. The vehicle must be driven 5–10 miles (8–16 km) to get an accurate reading.

FUEL Button The fuel button displays average fuel economy and instantaneous fuel economy, calculated for your specific driving conditions, and range information.

Average Fuel Economy: The average fuel economy is viewed as a long-term approximation of your overall driving conditions. You should reset the average fuel economy display every time you refuel. If you press the RESET button in this mode while you are driving, the system will reset this display and begin figuring fuel economy from that point in time. Press the fuel button to display average fuel economy, such as: (cid:129) AVERAGE FUEL ECONOMY 20.1 MPG or (cid:129) AVERAGE FUEL ECONOMY 11.7 L/100 km

Instantaneous Fuel Economy: Instantaneous fuel economy reflects only the fuel economy that the vehicle has right now and will change frequently as driving conditions change. Unlike average fuel economy, this menu item cannot be reset. Press the fuel button again to display instantaneous fuel economy, such as:

INSTANT FUEL ECONOMY 20.1 MPG or INSTANT FUEL ECONOMY 11.7 L/100 km

3-52

(cid:129) (cid:129) GAGES Button The gages button displays oil pressure, oil temperature, coolant temperature, transmission fluid temperature for automatic transmission vehicles only, battery voltage, and tire pressure information.

Oil Pressure: This display shows the oil pressure. Press the gages button to display the oil pressure, such as: (cid:129) OIL PRESSURE 40 PSI or (cid:129) OIL PRESSURE 276 kPa

Oil Temperature: This display shows the oil temperature. Press the gages button again to display the oil temperature, such as: (cid:129) OIL TEMPERATURE 234°F or (cid:129) OIL TEMPERATURE 112°C If the oil temperature is low, the display will show OIL TEMPERATURE LOW. If the oil temperature is high, the display will show OIL TEMPERATURE HIGH.

Coolant Temperature: This display shows the engine coolant temperature. Press the gages button again to display the coolant temperature, such as: (cid:129) COOLANT TEMPERATURE 123°F or (cid:129) COOLANT TEMPERATURE 51°C If the coolant temperature is low, the display will show COOLANT TEMPERATURE LOW. If the coolant temperature is high, the display will show COOLANT TEMPERATURE HIGH.

Transmission Fluid Temperature: If you have an automatic transmission vehicle, this display shows the automatic transmission fluid temperature. Press the gages button again to display the automatic transmission fluid temperature, such as:

TRANS FLUID TEMP 123°F or TRANS FLUID TEMP 51°C

If the transmission fluid temperature is low, the display will show TRANS FLUID TEMP LOW. If the transmission fluid temperature is high, the display will show TRANS FLUID TEMP HIGH.

3-53

(cid:129) (cid:129) Battery Voltage: This display shows the current battery voltage. Press the gages button again to display the battery voltage, such as: (cid:129) BATTERY VOLTAGE 13.5 VOLTS

Tire Pressure: This display shows the tire pressure for each tire. Press the gages button again to display the tire pressure for the front tires, such as:

FRONT TIRE PRESSURES L 34 PSI R 33 PSI or FRONT TIRE PRESSURES L 234 kPa R 228 kPa

Press the gages button again to display the tire pressure for the rear tires, such as: (cid:129) REAR TIRE PRESSURES L 34 PSI R 33 PSI or (cid:129) REAR TIRE PRESSURES L 234 kPa R 228 kPa

TRIP Button The TRIP button displays the odometer, trip distance, elapsed time, average speed, and oil life remaining information.

Odometer: The odometer shows how far your vehicle has been driven in either miles or kilometers. Press the TRIP button to display odometer readings, such as: (cid:129) ODOMETER 12345 MI or (cid:129) ODOMETER 20008 km You can also display the odometer by turning on the parking lamps.

Trip Odometers: There are two trip odometers. Press the TRIP button to display TRIP ODOMETER A readings and press the button again to display TRIP ODOMETER B readings, such as:

TRIP ODOMETER A 130.5 MI or TRIP ODOMETER A 209.9 km TRIP ODOMETER B 300.5 MI or TRIP ODOMETER B 483.5 km

Both of the trip odometers can be used simultaneously. The trip odometers can be reset by pressing the RESET button on the DIC.

3-54

(cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) There is also a miles since last ignition feature that displays the number of miles (kilometers) driven since you last started the vehicle. Press and hold the RESET button for three seconds, then release it. The miles (kilometers) since the last ignition cycle will be set into the trip odometer.

Elapsed Timer: Press the TRIP button until ELAPSED TIMER is displayed, such as ELAPSED TIMER .00. When the ignition is in on, the DIC can be used as a stopwatch. The display can show hours, minutes and seconds. The elapsed time indicator will record up to 23 hours, 59 minutes and 59 seconds, then it will reset to zero and continue counting. The display appears as ELAPSED TIMER .00 in the elapsed time function. You can start or stop the elapsed time by pressing the RESET button. To reset the elapsed time to zero, press the RESET button for three seconds while the timer is displayed. Pressing and holding the RESET button for at least 10 seconds will reset the timer display to the time since last ignition cycle.

Average Speed: Press the TRIP button until the average speed is displayed, such as: (cid:129) AVERAGE SPEED 62 MPH or (cid:129) AVERAGE SPEED 100 km/h Press and hold the RESET button to reset to 0.0 mph (km/h).

Engine Oil Life: Press the TRIP button until the engine oil life is displayed, such as OIL LIFE REMAINING 89%. This is an estimate of the engine oil’s remaining useful life. It will show 100% when the system is reset after an oil change. It will alert you to change the oil on a schedule consistent with your driving conditions. When the remaining oil life is low, the system will alert you with the message CHANGE ENGINE OIL. Remember, you must reset the engine oil life system yourself after each oil change. It will not reset itself. To reset the system, see Engine Oil Life System on page 5-26. Be careful not to reset the engine oil life system accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. See Scheduled Maintenance on page 6-4 and Engine Oil on page 5-19 for more information.

3-55

OPTION Button The OPTION button allows you to access the PERSONAL OPTIONS menu and customize the personalization settings on your vehicle. See DIC Vehicle Personalization on page 3-73 for more information. RESET Button The RESET button, used along with other buttons, will reset system functions and turn off or acknowledge messages on the DIC.

DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. You can scroll through the messages that may have been sent at the same time. The DIC is continuously updated with the vehicle performance status.

Some messages may not require immediate action, but you can press the RESET button to acknowledge that you received the messages and to clear them from the display. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear, not correct the problem. The following are the possible messages that can be displayed and some information about them. ABS (Antilock Brake System) ACTIVE This message displays when the Antilock Brake System (ABS) is adjusting brake pressure to help avoid a braking skid. Slippery road conditions may exist if this message is displayed, so adjust your driving accordingly. The message stays on for a few seconds after the system stops adjusting brake pressure. See Antilock Brake System (ABS) on page 4-5 for more information.

3-56

ACTIVE HANDLING This message displays when the Active Handling System is operating. The Active Handling System is a computer controlled system that assists the driver in controlling the vehicle in difficult driving conditions. You may feel or hear the system working and see the ACTIVE HANDLING message displayed in the DIC. This message stays on for a few seconds following the active handling event. This is normal when the system is operating. See Active Handling System on page 4-7 and Braking on page 4-4. ACTIVE HANDLING READY This message displays when the functional check of the Active Handling System has been completed. See Active Handling System on page 4-7 for more information. ATTACH TRUNK PARTITION If the vehicle has a power convertible top, this message displays and a sound will be heard if the trunk partition is not in place. Open the hatch/trunk and make sure the trunk partition is secure and no objects are on the trunk partition. See Rear Storage Area on page 2-53
for more information.

BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that features are disabled, this message is displayed. It means that the vehicle is trying to save the charge in the battery. Turn off unnecessary accessories to allow the battery to recharge. BUCKLE PASSENGER This message reminds you to buckle the passenger’s safety belt. This message displays and a sound will be heard when the ignition is on, the driver’s safety belt is buckled, the passenger’s safety belt is unbuckled with the passenger airbag enabled, and the vehicle is in motion. You should have the passenger buckle their safety belt. The reminder will be repeated if the ignition is on, the vehicle is in motion, the driver is buckled and the passenger is still unbuckled, and the passenger airbag is enabled. If the passenger’s safety belt is already buckled, this message will not come on.

3-57

BUCKLE SEATBELT This message reminds you to buckle the driver’s safety belt. This message displays and a sound will be heard when the ignition is on, the driver’s safety belt is unbuckled, and the vehicle is in motion. You should buckle your safety belt. If the driver remains unbuckled when the ignition is on and the vehicle is in motion, the reminder will be repeated. If the driver’s safety belt is already buckled, this message will not come on. This message is an additional reminder to the safety belt reminder light in the instrument panel cluster. See Safety Belt Reminders on page 3-35 for more information. CHANGE BRAKE PADS On vehicles with electronic brake pad wear sensors, this message will be displayed when the pads are worn. See your dealer/retailer for service.

CHANGE ENGINE OIL This message displays when the life of the engine oil has expired. See Scheduled Maintenance on page 6-4. After an oil change, the engine oil life system must be reset. See “Engine Oil Life” under DIC Operation and Displays on page 3-50. Also, see Engine Oil on page 5-19 and Engine Oil Life System on page 5-26
for more information. CHECK BRAKE FLUID This message displays, a sound will be heard, and the brake system warning light on the instrument panel cluster turns on if the ignition is on to inform the driver that the brake fluid level is low. See Brake System Warning Light on page 3-40. Have the brake system serviced by your dealer/retailer as soon as possible. See Brakes on page 5-43. CHECK COOLANT LEVEL This message displays when the engine coolant level is low. Have the cooling system serviced by your dealer/ retailer as soon as possible. See Engine Coolant on page 5-34.

3-58

CHECK GAS CAP This message displays if the fuel cap has not been fully tightened. Check the fuel cap to make sure that it is on properly. Once tightened, it takes at least one overnight park to reset or clear this message. If both the CHECK GAS CAP message and the malfunction indicator lamp in the instrument panel cluster are on, you may need to see your dealer/retailer for service. See Malfunction Indicator Lamp on page 3-44 for more information. CHECK OIL LEVEL On some vehicles, this message displays and two chimes sound if the oil level in the vehicle is low. Once the vehicle senses a change in the engine oil level, the light remains off. If this message appears after starting the engine, the engine oil level may be too low. You may need to add oil. See Engine Overheating on page 5-39. To acknowledge the message, press the RESET button. The message reappears every 10 minutes until this condition changes.

CLOSE TRUNK TO MOVE TOP This message displays and a sound will be heard if the trunk is open while you are trying to operate the convertible top. Make sure the trunk is closed before operating the convertible top. See Convertible Top (Manual) on page 2-62 or Convertible Top (Power) on page 2-69. COMPETITIVE DRIVING MODE This message displays and a sound will be heard when the Competitive Driving mode is selected. The instrument panel cluster light will be on when the Competitive Driving mode is selected. The Traction Control System (TCS) will not be operating while in the Competitive Driving mode. Adjust your driving accordingly. See Racing or Other Competitive Driving on page 4-14 for more information.

3-59

COOLANT OVER TEMPERATURE This message displays and a sound will be heard if the engine coolant exceeds 255°F (124°C). If you have been operating the vehicle under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible. You can monitor the coolant temperature with the gages button on the DIC or the engine coolant temperature gage on the instrument panel cluster. See Engine Overheating on page 5-39, DIC Operation and Displays on page 3-50, and Engine Coolant Temperature Gage on page 3-43. To acknowledge the message, press the RESET button. The message and sound will come back on until this condition changes. If you do not press the RESET button, the message remains on until the condition changes. CRUISE DISENGAGED This message displays briefly when you disengage the cruise control system by stepping on the brake on an automatic transmission vehicle or the clutch on a manual transmission vehicle, or by turning off the cruise control switch. See Cruise Control on page 3-10 for more information.

3-60

ENGINE DRAG CONTROL ACTIVE This message displays when engine drag control is active. When driving in a lower gear in rainy, snowy, or icy conditions and then letting up on the accelerator or downshifting, the rear wheels may begin to slip and this message displays. This message stays on for a few seconds following the engine drag control event. ENGINE OVERHEATED – STOP ENGINE This message displays and a sound will be heard when the engine has overheated. Stop and turn the engine off immediately to avoid severe engine damage. See Engine Overheating on page 5-39. ENGINE PROTECTION REDUCE ENGINE RPM This message displays if the engine oil temperature exceeds 320°F (160°C). Check the engine coolant temperature and engine oil level. If the engine is too hot, see Engine Overheating on page 5-39. The vehicle may need service, so see your dealer/retailer. You can monitor the oil temperature with the gages button on the DIC. See DIC Operation and Displays on page 3-50. Multiple chimes sound when this message is displayed. This message remains displayed and active until the issue is resolved.

HEADLAMPS SUGGESTED This message displays if it is dark enough outside and the headlamps and the Twilight Sentinel® controls are off. This message informs the driver that turning on the exterior lamps is recommended. It has become dark enough outside to require the headlamps and/or other exterior lamps. HIGH TIRE PRESSURE This message displays when one or more of the tires is over-inflated. This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate which tire is affected. You can receive more than one tire pressure message at a time. To read other messages that may have been sent at the same time, press the RESET button. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Run-Flat Tires on page 5-69, Loading the Vehicle on page 4-23, Inflation - Tire Pressure on page 5-71, and Tire Pressure Monitor System on page 5-73. The DIC also shows the tire pressure values. See DIC Operation and Displays on page 3-50. To acknowledge the message, press the RESET button. A message reappears every 10 minutes until the condition is corrected.

HOT ENGINE AIR CONDITIONING OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor is automatically turned off. When the coolant temperature returns to normal, the A/C operation automatically resumes. You can continue to drive the vehicle. If this message continues to appear, have the system repaired by your dealer/retailer as soon as possible to avoid compressor damage. ICE POSSIBLE This message displays when the outside air temperature is cold enough to create icy road conditions. Adjust your driving accordingly. LOW FUEL This message displays when the fuel tank is less than 10 percent full and the display is turned off. A sound will be heard when this message is displayed. Refill the fuel tank as soon as possible. See Fuel Gage on page 3-49.

3-61

This message displays when one or more of the tires is under-inflated. This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate which tire is affected. Multiple chimes sound and the tire pressure light on the instrument panel cluster turns on when this message is displayed. See Tire Pressure Light on page 3-43. You can receive more than one tire pressure message at a time. To read other messages that may have been sent at the same time, press the RESET button. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Run-Flat Tires on page 5-69, Loading the Vehicle on page 4-23, Inflation - Tire Pressure on page 5-71, and Tire Pressure Monitor System on page 5-73. The DIC also shows the tire pressure values. See DIC Operation and Displays on page 3-50. To acknowledge the message, press the RESET button. A message reappears every 10 minutes until the condition is corrected.

LOW OIL PRESSURE This message displays if low oil pressure levels occur. If this message appears while the engine is running, stop the engine and do not operate it until the cause of low oil pressure is corrected. Severe damage to the engine can result. A sound will be heard when this message is displayed. See Engine Oil on page 5-19. LOW TIRE PRESSURE

{ CAUTION:

When the LOW TIRE PRESSURE or TIRE FLAT message is displayed on the Driver Information Center, your vehicle’s handling capabilities will be reduced during severe maneuvers. The active handling system will be affected. See Active Handling System on page 4-7. If you drive too fast, you could lose control of your vehicle. You or others could be injured. Do not drive over 55 mph (90 km/h) when the LOW TIRE PRESSURE or TIRE FLAT message is displayed. Drive cautiously and check your tire pressures as soon as you can.

3-62

MAXIMUM SPEED 80 MPH (129 km/h) This message displays when a malfunction is present in the Selective Ride Control system. The vehicle speed will be limited to a value determined by the vehicle when the shock absorber system has failed and the shocks are in their full soft mode. Have the vehicle serviced by your dealer/retailer as soon as possible. To acknowledge the message, press the RESET button. The message reappears every 10 minutes until this condition changes. NO FOBS DETECTED This message displays if the vehicle does not detect the presence of a keyless access transmitter when you have attempted to start the vehicle or a vehicle door has just closed. The following conditions may cause this message to appear: (cid:129) Driver-added equipment plugged into the accessory

power outlet on the center console is causing interference. Examples of these devices are cell phones and cell phone chargers, two-way radios, power inverters, or similar items. Try moving the keyless access transmitter away from these devices when starting the vehicle. In addition, PDA devices and remote garage and gate openers may also generate Electromagnetic Interference (EMI) that may interfere with the keyless access transmitter. Do not carry the keyless access transmitter in the same pocket or bag as these devices.

The vehicle is experiencing Electromagnetic Interference (EMI). Some locations, such as airports, automatic toll booths, and some gas stations have EMI fields which may interfere with the keyless access transmitter.

If moving the transmitter to different locations within the vehicle does not help, place the transmitter in the glove box transmitter pocket with the buttons facing to the right and then press the START button. The vehicle’s battery voltage is low. The battery voltage must be above 10 volts for the keyless access transmitter to be detected properly.

3-63

(cid:129) (cid:129) NO FOB - OFF OR RUN? This message displays when the keyless access transmitter is not detected inside the vehicle while you are trying to turn the ignition off. The vehicle may be near a strong radio antenna signal causing the keyless access system to be jammed. The vehicle will remain in ACCESSORY until the vehicle is turned off or is restarted, or five minutes has expired. If you turn the ignition off and you cannot find the keyless access transmitter, you will not be able to restart the vehicle. The keyless access transmitter needs to be inside of the vehicle in order for the vehicle to start. See Starting the Engine on page 2-24
for more information. OPTIONS UNAVAILABLE This message displays for a few seconds if a keyless access transmitter that is not labelled 1 or 2 is used and you try to personalize the features on the vehicle by pressing the OPTION button. The personalization system will not recognize the transmitter and the DIC will not display the current driver number or the menus used to set personalizations. The personalization features will then be set to the default states. See DIC Vehicle Personalization on page 3-73 for more information.

PRESS BRAKE TO START ENGINE (Automatic Transmission Only) This message displays if you try to start the engine by pressing the keyless ignition start button without having the brake pressed. The brake needs to be pressed when starting the engine. See Ignition Positions on page 2-23
for more information. REDUCED ENGINE POWER If this message displays and the check engine light comes on, a noticeable reduction in the vehicle’s performance may occur. If the REDUCED ENGINE POWER message is displayed, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while the REDUCED ENGINE POWER message is displayed, but acceleration and speed may be reduced. Anytime the check engine light stays on, the vehicle should be taken to your dealer/retailer as soon as possible for diagnosis and repair. See Malfunction Indicator Lamp on page 3-44
for more information.

3-64

Multiple chimes sound when this message is displayed. To acknowledge the message, press the RESET button. The message reappears every five minutes until this condition changes. If the REDUCED ENGINE POWER message is displayed in combination with the COOLANT OVER TEMPERATURE message, see Engine Overheating on page 5-39. SERVICE ACTIVE HANDLING SYSTEM This message displays if there is a problem with the Active Handling System and the vehicle needs service. The active handling system light on the instrument panel cluster also turns on and a sound will be heard. See your dealer/retailer. When this message is displayed, the system is not working. Adjust your driving accordingly. See Active Handling System on page 4-7 for more information. SERVICE AIR CONDITIONING This message displays when the electronic sensors that control the air conditioning and heating systems are no longer working. Have the climate control system serviced by your dealer/retailer if you notice a drop in heating and air conditioning efficiency.

SERVICE ANTILOCK BRAKES If this message displays while you are driving, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the message stays on, or comes back on again while you are driving, the vehicle is in need of service. See your dealer/retailer. If the antilock brake system (ABS) warning light is on and the regular brake system warning light is not on, you still have brakes, but do not have ABS. If the regular brake system warning light is also on, you do not have ABS and there is a problem with the brakes. See Antilock Brake System (ABS) Warning Light on page 3-41 and Brake System Warning Light on page 3-40. If this message is displayed, the Traction Control System (TCS) and the Active Handling System will also be disabled. The DIC will scroll three messages: SERVICE ANTILOCK BRAKES, SERVICE TRACTION SYSTEM, and SERVICE ACTIVE HANDLING, and the instrument panel cluster lights will come on along with a sound. When the service message is displayed, the computer controlled systems will not assist the driver. Have the system repaired by your dealer/retailer as soon as possible. Adjust your driving accordingly. To acknowledge these messages, press the RESET button.

3-65

SERVICE RIDE CONTROL This message displays when the Selective Ride Control system has detected a malfunction and the system must be serviced. See your dealer/retailer. If a fault is present in the Selective Ride Control system which causes the shocks to be in their full soft condition, the messages SERVICE RIDE CONTROL, SHOCKS INOPERATIVE, and MAXIMUM SPEED 80 MPH (129 km/h) will display together. See Selective Ride Control on page 4-9 for more information. SERVICE TIRE MONITOR This message displays if a part on the Tire Pressure Monitor System (TPMS) is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 3-43. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 5-75 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer/retailer.

SERVICE CHARGING SYSTEM If this message displays while you are driving, there may be a problem with the electrical charging system. It could mean that there is a loose or broken drive belt or that there is another electrical problem. Have the vehicle checked right away by your dealer/retailer. Driving while this message is on could drain the battery. If you must drive a short distance with the message on, be certain to turn off the vehicle’s accessories, such as the radio and air conditioner. Multiple chimes sound when this message is displayed. To acknowledge the message, press the RESET button. The message reappears every 10 minutes until this condition changes. SERVICE ELECTRICAL SYSTEM This message displays if an electrical problem has occurred within the Powertrain Control Module (PCM). Have the vehicle serviced by your dealer/retailer. SERVICE FUEL SYSTEM This message displays if the Powertrain Control Module (PCM) has detected a problem within the fuel system. Have the vehicle serviced by your dealer/retailer. This message also displays when the cluster is not getting fuel information from the PCM.

3-66

SERVICE TRACTION SYSTEM If this message displays when you are driving, there is a problem with the Traction Control System (TCS) and the vehicle is in need of service. See your dealer/retailer. When this message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. The traction control system (TCS) warning light on the instrument panel cluster will also turn on and a sound will be heard. When this message is displayed, the computer controlled systems will not assist the driver in controlling the vehicle. Have the system repaired by your dealer/retailer as soon as possible. Adjust your driving accordingly. See Traction Control System (TCS) on page 4-6 for more information. To acknowledge the message, press the RESET button. SERVICE TRANSMISSION This message displays when there is a problem with the transmission. See your dealer/retailer for service. SERVICE VEHICLE SOON This message displays and a sound will be heard when there may be an electrical or another system problem with the vehicle. Have your vehicle checked by your dealer/retailer if this message keeps appearing.

SET PARK BRAKE FOR SEAT RECALL If the vehicle has a manual transmission, this message displays if you try to recall the memory positions when the ignition is on and the parking brake is not set. If the vehicle is on, you must set the parking brake in order for the memory positions to recall. See Memory Seat, Mirrors and Steering Wheel on page 1-4 for more information. SET PARK BRAKE TO MOVE TOP If the vehicle has a manual transmission, this message displays and a sound will be heard if you try to operate the power convertible top without first setting the parking brake. Set the parking brake before trying to operate the power convertible top. See Convertible Top (Manual) on page 2-62 or Convertible Top (Power) on page 2-69 for more information. SHIFT TO PARK If the vehicle has an automatic transmission, this message displays if the vehicle is not in P (Park) when the engine is being turned off. The vehicle will be in ACCESSORY Once the shift lever is moved to P (Park), the vehicle will turn off.

3-67

The vehicle will remain in ACCESSORY, without the 20 minute time-out period, until the shift lever is moved to P (Park) or until the driver presses the pushbutton to restart the vehicle. See Ignition Positions on page 2-23 for more information. SHIFT TO PARK OR SET PARK BRAKE FOR TOP If the vehicle has an automatic transmission, this message displays and a sound will be heard if you try to operate the power convertible top without first shifting into P (Park) or setting the parking brake. Either shift the vehicle into P (Park) or set the parking brake before trying to operate the power convertible top. See Convertible Top (Manual) on page 2-62 or Convertible Top (Power) on page 2-69 for more information. SHOCKS INOPERATIVE This message displays when a malfunction is present in the Selective Ride Control system which is causing the shocks to be in their full soft mode. This is a warning to the driver that the vehicle handling may be affected. Have the vehicle serviced by your dealer/retailer as soon as possible. To acknowledge the message, press the RESET button. The message reappears every 10 minutes until this condition changes.

3-68

TIRE FLAT

{ CAUTION:

When the LOW TIRE PRESSURE or TIRE FLAT message is displayed on the Driver Information Center, your vehicle’s handling capabilities will be reduced during severe maneuvers. If you drive too fast, you could lose control of your vehicle. You or others could be injured. Do not drive over 55 mph (90 km/h) when the LOW TIRE PRESSURE or TIRE FLAT message is displayed. Drive cautiously and check your tire pressures as soon as you can.

This message displays when one or more of the tires is flat. This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate which tire is affected. Multiple chimes sound and the tire pressure light on the instrument panel cluster comes on when this message is displayed. See Tire Pressure Light on page 3-43.

This message is followed by the MAXIMUM SPEED 55 MPH (90 km/h) message, and then by the REDUCED HANDLING message. The Active Handling System will intervene more quickly when a flat tire has been detected. Adjust your driving accordingly. You can receive more than one tire pressure message at a time. To read other messages that may have been sent at the same time, press the RESET button. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Run-Flat Tires on page 5-69, Loading the Vehicle on page 4-23, Inflation - Tire Pressure on page 5-71, and Tire Pressure Monitor System on page 5-73. The DIC also shows the tire pressure values. See DIC Operation and Displays on page 3-50. To acknowledge the message, press the RESET button. A message reappears every 10 minutes until the condition is corrected. TOO COLD TO MOVE TOP This message displays and a sound will be heard when the power convertible top button is pressed and the power convertible top pump motor temperature is below -4°F (-20°C). Wait for the power convertible top pump motor to warm up before using the power convertible top.

TOP MOTOR OVER TEMPERATURE This message displays and a sound will be heard when the power convertible top button is pressed and the power convertible top pump motor temperature is over 221°F (105°C). Wait for the power convertible top pump motor to cool down before using the power convertible top. TOP NOT SECURE This message displays and a sound will be heard when the power convertible top button is released before the top open or close operation is complete or if the top is closed without the header latch engaged. Press and hold the convertible top button to fully open or close the top, and make sure that the header latch is engaged after the top is closed. TRACTION SYSTEM ACTIVE This message displays when the Traction Control System (TCS) is limiting wheel spin. Slippery road conditions may exist if this message is displayed, so adjust your driving accordingly. The message stays on for a few seconds after the TCS stops limiting wheel spin. See Traction Control System (TCS) on page 4-6
for more information.

3-69

TRACTION SYSTEM – OFF This message displays and stays on, a sound will be heard, and the traction control system (TCS) warning light on the instrument panel cluster turns on when the TCS is turned off by pressing the Active Handling System button on the console. See Traction Control System (TCS) Warning Light on page 3-41. See Traction Control System (TCS) on page 4-6 for more information. To acknowledge the message, press the RESET button. TRACTION SYSTEM – ON This message displays and a sound will be heard when the Traction Control System (TCS) is turned on by pressing the Active Handling System button on the console. This message automatically clears from the DIC display on its own. See Traction Control System (TCS) on page 4-6 for more information.

TRACTION SYSTEM AND ACTIVE HANDLING – OFF This message displays, the instrument panel cluster light turns on, and a sound will be heard when the Traction Control System (TCS) and Active Handling System are turned off by pressing the Active Handling System button on the console for five seconds. The Antilock Brake System (ABS) remains on with the TCS and Active Handling System off. Adjust your driving accordingly. See Traction Control System (TCS) on page 4-6 and Active Handling System on page 4-7
for more information. To acknowledge this message, press the RESET button. TRACTION SYSTEM AND ACTIVE HANDLING – ON If the Traction Control System (TCS) and Active Handling System are off, this message displays briefly, the instrument panel cluster light turns off, and a sound will be heard when the TCS and Active Handling System are turned on by briefly pressing the Active Handling System button on the console. See Traction Control System (TCS) on page 4-6 and Active Handling System on page 4-7 for more information.

3-70

TRANSMISSION HOT IDLE ENGINE This message displays and four chimes sound if the transmission fluid temperature rises above 270°F (132°C) or rises rapidly. The transmission may shift gears or apply the torque converter clutch to reduce the fluid temperature. Driving aggressively or driving on long hills can cause the transmission fluid temperature to be higher than normal. If this message appears, you may continue to drive at a slower speed. Monitor the transmission fluid temperature and allow it to cool to at least 230°F (110°C). The transmission fluid temperature can be monitored with the gages button on the DIC. See DIC Operation and Displays on page 3-50 and Automatic Transmission Fluid on page 5-31. Also check the engine coolant temperature. If it is also hot, see Engine Overheating on page 5-39. If this message is displayed during normal vehicle operation on flat roads, the vehicle may need service. See your dealer/retailer for an inspection. If driving in a performance or competitive manner, the use of (S) Sport Automatic Mode or (S) Sport Manual Paddle Shift gear selection is recommended. See Automatic Transmission Operation on page 2-26
for more information.

To acknowledge the message, press the RESET button. The message reappears every 10 minutes until this condition changes. If you do not press the RESET button, the message remains on the display until the condition changes. TURN SIGNAL ON This message displays and a sound will be heard if a turn signal is left on for three-quarters of a mile (1.2 km). Move the turn signal/multifunction lever to the off position. To acknowledge this message, press the RESET button. UNLATCH HEADER TO MOVE TOP This message displays and a sound will be heard if you try to lower the convertible top without first unlocking the top. Move the latch handle to unlock the convertible top. See Convertible Top (Manual) on page 2-62 or Convertible Top (Power) on page 2-69.

3-71

Other Messages Here are more messages that you can receive on your Driver Information Center (DIC). To acknowledge a message and read another message that may have come on at the same time, press the RESET button. (cid:129) ACCESSORY MODE ON (cid:129) BATTERY VOLTAGE HIGH

See Voltmeter Gage on page 3-38.

(cid:129) BATTERY VOLTAGE LOW

See Voltmeter Gage on page 3-38.

(cid:129) CHECK WASHER FLUID

See Windshield Washer Fluid on page 5-42.

(cid:129) CRUISE SET TO XXX MPH (XXX km/h)

See Cruise Control on page 3-10.

(cid:129) DRIVER DOOR AJAR

FOB AUTOLEARN WAIT XX MINUTES See “Matching Transmitter(s) to Your Vehicle” under Keyless Access System Operation on page 2-5. FOB BATTERY LOW See “Battery Replacement” under Keyless Access System Operation on page 2-5.

(cid:129) HATCH AJAR (Coupe)

3-72

INTRUSION SENSOR OFF, if your vehicle has this feature INTRUSION SENSOR ON, if your vehicle has this feature

(cid:129) KNOWN FOB

See “Matching Transmitter(s) to Your Vehicle” under Keyless Access System Operation on page 2-5.

(cid:129) MAXIMUM NUMBER OF FOBS LEARNED

See “Matching Transmitter(s) to Your Vehicle” under Keyless Access System Operation on page 2-5.

(cid:129) OFF–ACCESSORY TO LEARN

See “Matching Transmitter(s) to Your Vehicle” under Keyless Access System Operation on page 2-5.

(cid:129) PASSENGER DOOR AJAR (cid:129) READY FOR FOB #X

See “Matching Transmitter(s) to Your Vehicle” under Keyless Access System Operation on page 2-5. TONNEAU AJAR (Convertible) TRUNK AJAR (Convertible)

(cid:129) UPSHIFT NOW

See Manual Transmission Operation on page 2-30.

(cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) DIC Vehicle Personalization Many features on your vehicle can be personalized. This means that the operation of these features can be set to operate differently depending on who is driving the vehicle. See “Personal Options” later in this section for the features that you can personalize. The personalization settings for other features are automatically updated and saved as the driver adjusts them. These include the following settings and presets:

The radio presets, tone, volume, fade, balance, equalization (EQ) settings and source (radio or CD) The last climate control setting The Head-Up Display (HUD) position and dimming level, if your vehicle has this feature The instrument panel cluster dimming level and last selected DIC display

Separate personalization settings are saved for two different drivers. One of the keyless access transmitters is assigned to driver 1. The other is assigned to driver 2. The back of the keyless access transmitters are labelled 1 or 2 to correspond to each driver.

The current driver’s preferences are recalled when one of the following occurs:

The lock or unlock button on the keyless access transmitter, labelled 1 or 2, is pressed. The appropriate memory button, 1 or 2, located on the driver’s door is pressed. See Memory Seat, Mirrors and Steering Wheel on page 1-4
for more information.

(cid:129) A valid keyless access transmitter is detected upon

opening the driver’s door.

If more than one valid keyless access transmitter is detected upon opening the driver’s door, the driver preferences for the lowest driver number will be recalled. If a keyless access transmitter that is not labelled 1 or 2
is used, the personalization system will not recognize the transmitter. The Driver Information Center (DIC) will not display a current driver number and the features that are normally programmed through the DIC will be set to the default states. Also, if the OPTION button is pressed, the DIC does not display the menus used to set personalizations, but instead displays OPTIONS UNAVAILABLE for a few seconds.

3-73

(cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) Entering the Personal Options Menu To enter the personal options menu, use the following steps: 1. If you have an automatic transmission vehicle, turn

the vehicle on with the shift lever in P (Park). If you have a manual transmission vehicle, turn the vehicle on with the parking brake set. To avoid excessive drain on the battery, it is recommended that the headlamps are turned off. 2. Press the OPTION button and you will enter the

PERSONAL OPTIONS menu. The DIC will display the current driver number (1 or 2) for a few seconds and then will display instructions on which buttons to use for setting the personalizations. The RESET button is used to select a setting for a particular feature. The OPTION button is used to move to the next feature.

3. Press the OPTION button while the instruction

screen is displayed to enter the first personalization menu item.

4. Once you have cycled through all of the personal

options, pressing the OPTION button a final time exits the personal options menu. In addition, if no button is pressed within 45 seconds, the DIC will exit the personal options menu.

3-74

Personal Options The following options are available for programming:

Display Units: This option allows you to choose the measurement units.

Press the OPTION button until DISPLAY UNITS appears on the display, then press the RESET button to scroll through the following modes: (cid:129) ENGLISH (default) (cid:129) METRIC If you choose ENGLISH, all information will be displayed in English units. If you choose METRIC, all information will be displayed in metric units. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

Auto Memory Recall (Automatic Transmission only): If your automatic transmission vehicle has the memory package, you may have this option. This option allows the driver’s seat, the telescopic steering column, if your vehicle has this feature, and the outside rearview mirrors to automatically move to the current driver’s set position when the engine starts.

Press the OPTION button until AUTO MEMORY RECALL appears on the display, then press the RESET button to scroll through the following modes: (cid:129) YES (cid:129) NO (default) If you choose YES, the driver’s seat, the outside rearview mirrors and the telescopic steering column, if your vehicle has this feature, positions are recalled when you turn the ignition on. If you choose NO, this option will turn off. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

Auto Exit Recall: If your vehicle has the memory package, you may have this option. This option allows the driver’s seat and telescopic steering column, if your vehicle has this feature, to automatically move to the current driver’s exit position when one of the following occurs:

The vehicle is turned off or in Retained Accessory Power (RAP) or accessory mode and the driver’s door is opened. The vehicle is turned off or in RAP and the unlock button on the keyless access transmitter is pressed.

In order for the Auto Exit Recall feature to work on an automatic transmission vehicle, the vehicle must be in P (Park). On a manual transmission vehicle, the parking brake must be set. Press the OPTION button until AUTO EXIT RECALL appears on the display, then press the RESET button to scroll through the following modes: (cid:129) YES (cid:129) NO (default) If you choose YES, when you turn the ignition off and open the driver’s door or press the unlock button on the keyless access transmitter, the seat and the telescopic steering wheel, if your vehicle has this feature, will return to their stored exit positions for an easy exit or an easy entrance when returning to the vehicle. The seat and steering wheel will only return to the stored driving position if you press the appropriate memory button or activate the auto memory recall feature. If you choose NO, this option will turn off. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

3-75

(cid:129) (cid:129) Approach Lights: This option briefly turns on the parking lamps, the high-beam headlamps and the back-up lamps during low light periods when the keyless access transmitter is used to unlock the vehicle.

Press the OPTION button until APPROACH LIGHTS appears on the display, then press the RESET button to scroll through the following modes: (cid:129) OFF (cid:129) ON (default) If you choose OFF, this option will turn off. If you choose ON, the parking lamps, the high-beam headlamps, and the back-up lamps will come on for 20 seconds during low light periods when all of the following occurs: (cid:129) You press the unlock button on the keyless access

transmitter.

(cid:129) Both of the doors are closed. The vehicle is off or in RAP.

The lamps remain on for 20 seconds or until a door is opened, the lock button on the keyless access transmitter is pressed or the vehicle is no longer off or in RAP. See Keyless Access System on page 2-4 for more information.

When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

Twilight Delay: This option allows you to set the amount of time you want the parking lamps and high-beam headlamps to remain on after you exit the vehicle. This will occur when the vehicle is off or in RAP and the headlamps are on due to the automatic headlamp system. The parking lamps and high-beam headlamps will remain on until the driver selected time expires, the exterior lamp control is activated or the vehicle is no longer off or in RAP. Press the OPTION button until TWILIGHT DELAY appears on the display, then press the RESET button to scroll through the following modes: (cid:129) OFF 15 S 30 S (default) 90 S

If you choose OFF, this option will turn off. If you choose 15 S, the twilight delay time will be set to 15 seconds. If you choose 30 S, the twilight delay time will be set to 30 seconds.

3-76

(cid:129) (cid:129) (cid:129) (cid:129) If you choose 90 S, the twilight delay time will be set to 90 seconds. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

Flash at Unlock: This option activates the front and rear turn signals for two short flashes when the unlock or hatch/trunk button on the keyless access transmitter is pressed. This will only occur when the vehicle is off.

Press the OPTION button until FLASH AT UNLOCK appears on the display, then press the RESET button to scroll through the following modes: (cid:129) YES (default) (cid:129) NO If you choose YES, the front and rear turn signals will flash twice when you press the unlock button or the hatch/trunk button on the keyless access transmitter. If you choose NO, this option will turn off. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

Flash at Lock: This option activates the front and rear turn signals for one long flash when the lock button on the keyless access transmitter is pressed. This will only occur when the vehicle is off. If the lock button on the keyless access transmitter is pressed again within five seconds, the horn will sound regardless of which setting you have selected.

Press the OPTION button until FLASH AT LOCK appears on the display, then press the RESET button to scroll through the following modes: (cid:129) YES (default) (cid:129) NO If you choose YES, the front and rear turn signals will flash once when you press the lock button on the keyless access transmitter. If you choose NO, this option will turn off. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

3-77

FOB Reminder: This option sounds the horn three times when the driver’s door is closed and there is a keyless access transmitter inside the interior of the vehicle. This will only occur when the vehicle is off.

Press the OPTION button until FOB REMINDER appears on the display, then press the RESET button to scroll through the following modes: (cid:129) YES (cid:129) NO (default) If you choose YES, the horn will sound three times when a keyless access transmitter is inside of the vehicle while the ignition is turned off and the driver’s door is closed. If you choose NO, this option will turn off. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

Passive Door Locking: This option allows you to select whether the doors automatically lock during normal vehicle exit. When the ignition is turned off and all doors become closed, the vehicle will determine how many keyless access transmitters remain in the vehicle interior. If at least one keyless access transmitter has been removed from the interior of the vehicle, the doors will lock after a short delay.

For example, if there are two keyless access transmitters in the vehicle and one is removed, the other will be locked in. The keyless access transmitter locked in the vehicle can still be used to start the vehicle or unlock the doors, if needed. A person approaching the outside of the locked vehicle without an authorized keyless access transmitter, however, will not be able to open the door, even with a transmitter in the vehicle.

You may temporarily disable the passive door locking feature by pressing the door unlock switch for three seconds on an open door. Passive door locking will then remain disabled until a door lock switch is pressed or until the power mode transitions from the off power mode.

Press the OPTION button until PASSIVE DOOR LOCKING appears on the display, then press the RESET button to scroll through the following modes: (cid:129) OFF (default) (cid:129) SILENT (cid:129) HORN If you choose OFF, this option will turn off. If you choose SILENT, the doors will automatically lock a short time after you remove a keyless access transmitter from the interior of the vehicle and close both doors.

3-78

If you choose HORN, the doors will automatically lock and the horn will sound a short time after you remove a keyless access transmitter from the interior of the vehicle and close both doors. If you are parking in a quiet area and do not want the horn to sound when the doors lock, press the lock button on the keyless access transmitter immediately after removing it from the interior and closing the doors. This will lock the doors and cancel the passive locking for this ignition cycle. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

Passive Door Unlock: This option allows you to select which doors will automatically unlock when you approach and open the driver’s door with the keyless access transmitter. See Door Locks on page 2-10 for more information. Press the OPTION button until PASSIVE DOOR UNLOCK appears on the display, then press the RESET button to scroll through the following modes: (cid:129) DRIVER (default) (cid:129) BOTH If you choose DRIVER, only the driver’s door will automatically unlock when you approach and open the driver’s door with the keyless access transmitter.

If you choose BOTH, both doors will automatically unlock when you approach and open the driver’s door with the keyless access transmitter.

Auto Unlock: This option allows you to select whether the driver’s door, both doors or neither door automatically unlocks when the shift lever is moved into P (Park) for automatic transmission vehicles or when the ignition is turned off or is in RAP for manual transmission vehicles.

Press the OPTION button until AUTO UNLOCK appears on the display, then press the RESET button to scroll through the following modes: (cid:129) OFF (cid:129) DRIVER (cid:129) BOTH (default) If you choose OFF, this option will turn off. If you choose DRIVER, on automatic transmission vehicles, the driver’s door will automatically unlock when the shift lever is moved into P (Park). On manual transmission vehicles, the driver’s door will automatically unlock when the ignition is turned off or is in RAP. If you choose BOTH, on automatic transmission vehicles, both doors will automatically unlock when the shift lever is moved into P (Park). On manual transmission vehicles, both doors will automatically unlock when the ignition is turned off or is in RAP.

3-79

When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option.

Language: This option allows you to select the language the DIC, the Head-Up Display (HUD), if your vehicle has this feature, and the radio uses to display messages. Each language mode will be displayed in its own language. For example, English will be displayed as ENGLISH, Spanish as ESPANOL, etc. If your vehicle has the navigation system, you will not have the Japanese language mode. Press the OPTION button until LANGUAGE appears on the display, then press the RESET button to scroll through the following modes: (cid:129) ENGLISH (default) (cid:129) DEUTSCH (German) FRANCAIS (French) ITALIANO (Italian)

(cid:129) ESPANOL (Spanish) If you choose a language that you do not understand, press the OPTION and RESET buttons for five seconds. The DIC will begin displaying all of the various languages one by one for as long as the buttons are pressed. When the desired language is displayed, release the buttons and the DIC will set to this language.

Personalize Name: This option allows you to type in a name or greeting that will appear on the DIC display whenever the corresponding keyless access transmitter (1 or 2) is used or one of the memory buttons (1 or 2) located on the driver’s door is pressed. Press the OPTION button until PERSONALIZE NAME appears on the display, then press the RESET button to scroll through the following modes: (cid:129) YES (cid:129) NO (default) If you choose YES, you can type in a name that will appear on the DIC display. To program a name, use the following procedure: 1. Enter the PERSONAL OPTIONS menu and

select the driver number (1 or 2) that you would like to program by following the instructions listed previously under “Entering the Personal Options Menu”.

2. Press the OPTION button until the PERSONALIZE

NAME option appears on the display.

3. Select YES under PERSONALIZE NAME by

pressing the RESET button.

3-80

(cid:129) (cid:129) 4. Press the OPTION button and a cursor will display

where you can insert a letter.

5. Press the OPTION button again until the letter you want is displayed. To scroll through the letters faster and without a beeping noise, keep the OPTIONS button depressed. There are alpha/numeric characters and a blank space available.

6. Then press the RESET button to select the letter of

your choice and proceed on to the next space to the right. If you make a mistake and would like to clear or replace a letter, perform the following steps:

6.1. Press the RESET button to reach the letter

you would like to change.

6.2. Press the OPTION button to scroll through

the letter choices.

6.3. Press the RESET button to select the letter and proceed on to the next space to the right.

7. Repeat Steps 5 and 6 until the name or greeting you want is complete. After the name or greeting is complete, keep pressing the RESET button until the display turns blank and exits out of this option. You can program up to 20 characters.

If you choose NO, this option will turn off. If a customized name or greeting is not programmed, the DIC display will show Driver 1 or Driver 2 to correspond with either the number on the back of the keyless access transmitter (1 or 2) that is being used or to the memory button (1 or 2) that is pressed. PERSONALIZE NAME is the last option available to program in the PERSONAL OPTIONS menu. Pressing the OPTION button after this setting will exit you from the PERSONAL OPTIONS menu. The last item you were in prior to entering PERSONAL OPTIONS will then display on the DIC.

3-81

Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features.

{ CAUTION:

Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.

This system provides access to many audio and non audio listings. To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: (cid:129) Become familiar with the operation and controls of

the audio system.

(cid:129) Set up the tone, speaker adjustments, and preset

radio stations.

For more information, see Defensive Driving on page 4-2.

3-82

Notice: Contact your dealer/retailer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the vehicle’s engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment. The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 2-24 for more information.

Setting the Clock To set the clock: 1. Press and hold H until the correct hour displays. 2. Press and hold M until the correct minute displays. 3. Press the tune knob to select between the 12 or

24 hour display format.

The clock mode automatically times out with the changed display format set as the current default setting.

Radio(s)

Playing the Radio

Top Knob (Power/Volume): Press to turn the system on and off. Turn to increase or decrease the volume.

MUTE: Press to silence the system. Press again to turn the sound on.

This button is not available on the Six-Disc CD Radio.

4 (Information): Press until the desired display is shown, then hold for two seconds until radio beeps once to change the default display. The selected display is now the default.

For RDS: Press 4 to change the display. The display options are station name, RDS station frequency, PTY, and the name of the program (if available).

For XM™: Press 4 to retrieve four different categories of information related to the current song or channel: Artist, Song Title, Category or PTY, Channel Number/Channel Name.

3-83

Single CD Radio shown, Six-Disc CD Radio similar

The vehicle has one of these radios as its audio system. An indicator light on the upper left side of the radio flashes when the ignition is off, to indicate the theft deterrent feature is set. For more information, see Theft-Deterrent Feature on page 3-107.

Audio Settings Press and hold O e when no tone or speaker control is displayed to adjust all tone and speaker controls to the middle position. AUDIO SETTINGS CENTERED displays. Adjusting the Tone (Bass/Treble) O e (Bass/Treble): To adjust the Bass or Treble: Press and release O e until BASS or TREBLE displays.

Turn the O e knob to increase or to decrease the level.

(cid:129) Press and hold the O e knob until the level

changes to the middle position.

Adjusting the Speakers (Balance/Fade) O e (Balance/Fade): To adjust the Balance: Press and release O e until BALANCE displays.

Turn the O e knob to move the sound toward the right or the left speakers.

(cid:129) Press and hold the O e knob until the level

changes to the middle position.

3-84

To adjust the Fade: Press and release O e until FADE displays

Turn the O e knob to move the sound toward the front or the rear speakers.

(cid:129) Press and hold the O e knob until the level