2008 Chevrolet Corvette Owners Manual

Download PDF Manual
front of the door handle and push the door open. You will hear a tone when the button is pressed. If power to the vehicle or the keyless access transmitter is lost, there are two ways to open the door. Door Open to Show Location of Door Handle Sensor When you have the transmitter with you, you may also unlock and open the door by squeezing the door handle sensor (A). You do not have to press the unlock button on the transmitter. You will be able to open the door when you press the door handle sensor and the vehicle recognizes your keyless access transmitter. When the passenger door is opened ﬁrst, the driver’s door will also unlock. From the inside, use the power door lock switch located at the top of the door panel near both windows. See Power Door Locks on page 2-12. From inside the vehicle, use the door release handle located on the ﬂoor next to each seat. Pull the handle up to unlock and unlatch the door. 2-11 Power Door Locks The power door lock switches are located on the doors. There is an indicator light on the rear of the door near the window. K(Unlock): Press to unlock the doors. When pressed, a beep sounds. If the door is closed when pressed, the light ﬂashes twice. If the door is open when pressed, the light ﬂashes. Q(Lock): Press to lock the doors. When pressed, a beep sounds. If the door is closed when pressed, the light comes on for a few seconds, then turns off. If the door is open when pressed, the light stays on. From outside the vehicle, use the key in the cylinder above the license plate to open the hatch then use the door release tab located on the carpet inside the trunk on the driver’s side of the vehicle. Pull the tab to unlock and unlatch the driver’s door. See Keys on page 2-3 for information on opening the trunk during a loss of power. 2-12 Automatic Door Lock Your vehicle is programmed so that, when the doors are closed, the ignition is on and the shift lever is moved out of PARK (P) for automatic transmissions, or when vehicle speed becomes faster than 8 mph (13 km/h) for manual transmissions, both doors will lock. If someone needs to get out while the vehicle is running or not in PARK (P), have the person use the power door unlock switch. When the door is closed again, the doors will lock either when your foot is removed from the brake or the vehicle speed becomes faster than 8 mph (13 km/h). Programmable Automatic Door Unlock Your vehicle is programmed so that when the shift lever is moved into PARK (P) for automatic transmission vehicles or when the ignition is turned off or is in Retained Accessory Power (RAP) for manual transmission vehicles, both doors will unlock. With the vehicle stopped and the engine running, door unlocking can be programmed through prompts displayed on the Driver Information Center (DIC). These prompts allow the driver to choose various unlock settings. For programming information, see DIC Vehicle Personalization on page 3-72. Lockout Protection Your vehicle can be programmed to sound the horn three times and unlock the driver’s door when both doors are closed and there is a keyless access transmitter inside the vehicle. When the driver’s door is opened, a reminder chime will sound continuously. The vehicle will remain locked only when at least one transmitter has been removed from the vehicle and both doors are closed. See DIC Vehicle Personalization on page 3-72. 2-13 Notice: Closing the hatch/trunk lid forcefully or from the sides can cause damage to the glass, the defogger or the weather stripping. Be sure objects will ﬁt in the hatch/trunk area before closing the hatch/trunk lid. When closing the hatch/trunk lid, gently pull down from the center. Notice: Do not store heavy or sharp objects in the rear storage compartments located in the hatch/trunk area. If you do, the objects could damage the underbody. Hatch {CAUTION: It can be dangerous to drive with the hatch/trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You can not see or smell CO. It can cause unconsciousness and even death. If you must drive with the hatch/trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the hatch/trunk lid: (cid:129) Make sure all other windows are shut. (cid:129) Turn the fan on your heating or cooling system to its highest speed and select the control setting that will force outside air into your vehicle. See Dual Automatic Climate Control System on page 3-25. If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 2-37. 2-14 (cid:129) Hatch/Trunk Lid Release There are several ways to release the hatch/trunk lid. If your vehicle has an automatic transmission, the shift lever must be in PARK (P). For manual transmission vehicles, the parking brake must be set when the ignition is started for the hatch/trunk release to operate. The parking brake does not need to be set when the ignition is off for the hatch/trunk release to operate. See Parking Brake on page 2-34. (cid:129) V (Hatch/Trunk): Press the hatch/trunk lid release button, located on the instrument panel to the left of the steering wheel. The theft-deterrent alarm system must not be armed. (cid:129) } (Hatch/Trunk): Press the hatch/trunk lid release button on the keyless access transmitter. See Keyless Access System on page 2-4. (cid:129) Press the hatch/trunk release button located on the rear of the hatch/trunk lid above the license plate, as long as you have your transmitter with you. If your vehicle has lost battery power, open the hatch/trunk using the vehicle key. See Keys on page 2-3 for more information. The key lock cylinder is located on the rear of the hatch/trunk lid above the license plate. Turn the vehicle key clockwise in the lock. Closing the Rear Compartment (Coupe) To assist in closing the rear compartment lid of your coupe, use the pocket on the underside of the lid on the passenger’s side of the vehicle. When closing the lid, lower it until the power pull down latch feature activates and it will close the rest of the way and latch automatically. 2-15 Emergency Trunk Release Handle (Convertible Only) Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle. The emergency trunk release handle is only intended to aid a person trapped in a latched trunk, enabling them to open the trunk from the inside. There is a glow-in-the-dark emergency trunk release handle located on the rear wall of the trunk below the latch. This handle will glow following exposure to light. Pull the release handle down to open the trunk from the inside. 2-16 Power Windows The power window switches are located on each door. Pull up or press down on the front of the switch to raise or lower the window. Retained Accessory Power (RAP) allows you to use the power windows when the ignition is off. For more information, see Retained Accessory Power (RAP) on page 2-23. Express-Down Window This feature is on both power windows. Press the front of the switch to the second position to activate the express-down feature. If you want to stop the window as it is lowering, press the switch again. 2-17 Window Indexing This feature automatically lowers the window a small amount when the door is opened. When the door is closed, the window will raise to its full up position. If either window does not index properly, it could be due to loss of power. Before returning to your dealer/retailer for service, perform the power window initialize procedure. Power Window Initialize After a power reconnect such as battery replacement, the window index-up feature will not function until the system is initialized. Once power is restored: 1. Close the door. 2. Raise the window and hold the switch up for three seconds after the window is closed. 3. Release the switch, then hold the switch up again for three seconds and release. Sun Visors To block out glare, you can swing down the visors. You can also swing them to the side. Lighted Visor Vanity Mirrors Pull down the sun visor and lift the cover to expose the lighted vanity mirror. When the cover is lifted, the lamps will come on automatically, even if the ignition is off. Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Theft-Deterrent System Your vehicle is equipped with a theft-deterrent alarm system. With this system, the security light will ﬂash when the door is open and locked with the power door lock switch. If this light is on continuously while the engine is running, your vehicle needs service. 2-18 Arming the System To arm the system: (cid:129) Press the lock button on the keyless access transmitter. (cid:129) Open the door. Lock the door with the power door lock switch. The security light should ﬂash. Remove the keyless access transmitter from inside the vehicle and close the door. The security light will stop ﬂashing and stay on. After 30 seconds, the light should turn off. The vehicle can be programmed to automatically lock the doors and arm the theft-deterrent system when you exit the vehicle. See DIC Vehicle Personalization on page 3-72. Now, if a door or the hatch/trunk is opened without the keyless access transmitter, the alarm will go off. Your horn will sound for two minutes, then it will go off to save battery power. Your vehicle will not start without a keyless access transmitter present. The theft-deterrent system will not arm if you lock the driver’s door with the power door lock switch after the doors are closed. If your passenger stays in the vehicle when you leave with the keyless access transmitter, have the passenger lock the vehicle after the doors are closed. This way the alarm will not arm, and your passenger will not set it off. Testing the Alarm To test the system: 1. Make sure the trunk lid/hatch is latched. 2. Lower the window on the driver’s door. 3. Manually arm the system. 4. Close the doors and wait 30 seconds. 5. Reach through the open window and manually pull the release lever on the ﬂoor. 6. Turn off the alarm by pressing the unlock button on the transmitter. If the alarm is inoperative, check to see if the horn works. If not, check the horn fuse. See Fuses and Circuit Breakers on page 5-96. If the horn works, but the alarm doesn’t go off, see your dealer/retailer. Disarming the System Always use your keyless access transmitter to unlock a door either by pressing the unlock button on the transmitter or by squeezing the door handle sensor while you have the transmitter with you. Unlocking a door any other way will set off the alarm. If your alarm sounds, press the unlock button on the keyless access transmitter to disarm it. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle. 2-19 Immobilizer This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Immobilizer Operation Your vehicle has a passive theft-deterrent system. The system is automatically armed when the ignition mode transitions to off. The immobilization system is disarmed when the ignition mode transitions to OFF/ACCESSORY or START and a valid transmitter is found in the vehicle. You do not have to manually arm or disarm the system. The security light will come on if there is a problem with arming or disarming the theft-deterrent system. The system has one or more keyless access transmitters that are matched to an immobilizer control unit in your vehicle. Only a correctly matched keyless access transmitter will start the vehicle. If the keyless access transmitter is ever damaged, you may not be able to start your vehicle. When trying to start the vehicle, if the engine does not start and the security light comes on, there may be a problem with your immobilizer system. Press the START button again. 2-20 If the vehicle does not start and the keyless access transmitter appears to be undamaged, try another keyless access transmitter. Or, you may try placing the transmitter in the transmitter pocket. See “NO FOBS DETECTED” under DIC Warnings and Messages on page 3-55 for additional information. At this time, you may also want to check the fuse. See Fuses and Circuit Breakers on page 5-96. If the engine still does not start with the other transmitter, your vehicle needs service. If the engine does start, the ﬁrst transmitter may be faulty. See your dealer/retailer who can service the theft-deterrent system and have a new keyless access transmitter programmed to the vehicle. It is possible for the immobilizer system to learn new or replacement keyless access transmitters. Up to 4 keyless access transmitters can be programmed for the vehicle. To program additional transmitters, see “Matching transmitter(s) to Your Vehicle” under Keyless Access System Operation on page 2-5. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle. Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:129) Keep your speed at 55 mph (88 km/h) or less for the ﬁrst 500 miles (805 km). (cid:129) Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. Avoid downshifting to brake or slow the vehicle. (cid:129) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time the new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. Following break-in, engine speed and load can be gradually increased. 2-21 Front Air Dam Your vehicle is equipped with a front air dam which has minimal ground clearance. Under normal operation, the air dam will occasionally contact some road surfaces (speed bumps, driveway ramps, etc.). This can be heard inside the vehicle as a scraping noise. This is normal and does not indicate a problem. Use care when approaching bumps or objects on road surfaces and avoid them when possible. Ignition Positions Your vehicle has an electronic keyless ignition with a pushbutton start. In order to shift out of PARK (P), the vehicle must be running or in ACCESSORY mode and the regular brake pedal must be applied. / (START): Press this button while your foot is on the brake for an automatic transmission, or while pressing in the clutch for a manual transmission, to start the engine. If your vehicle is in OFF or Retained Accessory Power (RAP) mode, the keyless access transmitter must be inside the vehicle to start the engine. 2-22 9 Acc. (OFF/ACCESSORY): When the engine is on or the vehicle is in accessory power mode, it is recommended that a manual transmission be placed in REVERSE (R). An automatic transmission must be placed in PARK (P). Then press the Acc. button to turn the engine off and place the vehicle in RAP. See “Retained Accessory Power (RAP)” later for more information. If an automatic vehicle is not correctly placed in PARK (P) a SHIFT TO PARK message will display on the Driver Information Center (DIC). For more information, see DIC Warnings and Messages on page 3-55. When the engine is off, press this button to place the vehicle in accessory mode. ACCESSORY MODE ON will display on the Driver Information Center (DIC). This mode allows you to use things like the radio and the windshield wipers while the engine is off. Use accessory mode if you must have your vehicle in motion while the engine is off, for example, if your vehicle is being pushed or towed. After being in accessory mode for about 10 minutes, the vehicle will automatically enter RAP or OFF, depending on if the doors are opened or closed. Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the engine is turned off: (cid:129) Audio System (cid:129) Power Windows These features continue to work up to 10 minutes after the engine is turned off or until either door is opened. If a door is opened, the power windows and audio system will shut off. Starting the Engine Move the shift lever to PARK (P) or NEUTRAL (N) for an automatic transmission. For a manual transmission the vehicle can be started in NEUTRAL or any other gear as long as the clutch is depressed. To restart a manual transmission when you are already moving, use the NEUTRAL position only. To restart an automatic transmission when you are already moving, use NEUTRAL (N). Notice: Do not try to shift to PARK (P) if your vehicle is moving. If you do, you could damage the transmission. Shift to PARK (P) only when your vehicle is stopped. The keyless access transmitter must be inside the vehicle for the ignition to work. 2-23 Cell phone chargers can interfere with the operation of the Keyless Access System. Battery chargers should not be plugged in when starting or turning off the engine. To start your vehicle, do the following: 1. For an automatic transmission, with your foot on the brake pedal, press the START button located on the instrument panel. For a manual transmission, while pressing in the clutch, press the START button. If there is not a keyless access transmitter in the vehicle or if there is something causing interference with it, the DIC will display NO FOBS DETECTED. See DIC Warnings and Messages on page 3-55 for more information. 2. When the engine begins cranking, let go of the button and the engine cranks automatically until it starts. If the battery in the keyless access transmitter is weak, the DIC displays FOB BATTERY LOW. You can still drive the vehicle. See “Battery Replacement” under Keyless Access System Operation on page 2-5 for more information. If the fob battery is dead, you need to insert the fob into the fob slot to enable engine starting. See “No Fobs Detected” under DIC Warnings and Messages on page 3-55. 3. Do not race the engine immediately after starting it. Operate the engine and transmission gently until the oil warms up and lubricates all moving parts. 4. If the engine does not start and no DIC message is displayed, wait 15 seconds before trying again to let the cranking motor cool down. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be ﬂooded with too much gasoline. Try pushing the accelerator pedal all the way to the ﬂoor while cranking for up to 15 seconds maximum. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go of the accelerator. If the vehicle starts brieﬂy but then stops again, do the same thing. This clears the extra gasoline from the engine. Notice: Cranking the engine for long periods of time, by pressing the START button immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. 2-24 Your vehicle has a Computer-Controlled Cranking System. This feature assists in starting the engine and protects components. Once cranking has been initiated, the engine continues cranking for a few seconds or until the vehicle starts. If the engine does not start, cranking automatically stops after 15 seconds to prevent cranking motor damage. To prevent gear damage, this system also prevents cranking if the engine is already running. Notice: The engine is designed to work with the electronics in your vehicle. If electrical parts or accessories are added, you could change the way the engine operates. Before adding electrical equipment, check with your dealer/retailer. If you do not, the engine might not perform properly. Any resulting damage would not be covered by your vehicle’s warranty. Stopping Your Engine If your vehicle has an automatic transmission, move the shift lever to PARK (P) and press and hold the Acc. (Off/Accessory) button, located on the instrument panel, until the engine shuts off. If the shift lever is not in PARK (P), the engine shuts off and the vehicle goes into the Accessory Mode. The DIC displays SHIFT TO PARK. Once the shifter is moved to PARK (P), the vehicle turns off. If your vehicle has a manual transmission, it is recommended that you move the shift lever to REVERSE (R) and set the parking brake after you turn off the engine by pressing the Acc. (Off/Accessory) button. If the keyless access transmitter is not detected inside the vehicle when it is turned to off, the DIC displays NO FOB – OFF OR RUN?. See DIC Warnings and Messages on page 3-55 for more information. Engine Coolant Heater The engine coolant heater, if available, can help in cold weather conditions at or below 0°F (−18°C) for easier starting and better fuel economy during engine warm-up. Plug in the coolant heater at least four hours before starting your vehicle. An internal thermostat in the plug-end of the cord may exist which will prevent engine coolant heater operation at temperatures above 0°F (−18°C). 2-25 To Use The Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The electrical cord is located on the driver’s side of the engine compartment, in front of the coolant surge tank. 3. Plug it into a normal, grounded 110-volt AC outlet. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer/retailer in the area where you will be parking your vehicle. The dealer/retailer can give you the best advice for that particular area. Automatic Transmission Operation There are several different positions for your shift lever. 2-26 PARK (P): This position locks your rear wheels. It is the best position to use when you start your engine because your vehicle cannot move easily. {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into PARK (P) (Automatic Transmission) on page 2-35. Be sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transmission shift lock control system. You have to fully apply your regular brakes ﬁrst and then press the shift lever button before you can shift from PARK (P) when the vehicle is running. If you cannot shift out of PARK (P), ease pressure on the shift lever and push the shift lever all the way into PARK (P) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of PARK (P) on page 2-36. REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice, or sand without damaging your transmission, see If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 4-23. 2-27 NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. If your vehicle needs towing, see Towing Your Vehicle on page 4-29. {CAUTION: Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) with the engine running at high speed may damage the transmission. The repairs would not be covered by your warranty. Be sure the engine is not running at high speed when shifting your vehicle. DRIVE (D): This position is for normal driving. It provide the best fuel economy for your vehicle. If you need more power for passing, and you are: (cid:129) Going less than about 35 mph (56 km/h), push the accelerator pedal about halfway down. (cid:129) Going about 35 mph (56 km/h) or more, push the accelerator all the way down. Downshifting the transmission in slippery road conditions could result in skidding, see “Skidding” under Loss of Control on page 4-13. SPORT MODE (S): When in SPORT MODE (S), the transmission will work as an automatic until you use the Manual Paddle Shift Controls, which activates the driver manual gear selection. See Manual Paddle Shift later in this section. While in automatic SPORT MODE (S), the transmission computer determines when the vehicle is being driven in a competitive manner and will select and hold the transmission in lower gears and have more noticeable upshifts for sportier vehicle performance. 2-28 Manual Paddle Shift While in the SPORT MODE (S) position, the paddles located on the steering wheel, can be used to manually up-shift or down-shift the transmission. While in the SPORT MODE (S) mode, push the paddle above the steering wheel spokes to up-shift to the next gear, or pull on the paddle behind the steering wheel spokes to down-shift to the next gear. To use the system, shift from PARK (P) position to SPORT MODE (S) while stopped and with the engine running, or from DRIVE (D) with the vehicle moving. When accelerating your vehicle from a stop in snowy and icy conditions, you may want to shift to second (2) or third (3) gear. A higher gear allows you to gain more traction on slippery surfaces. If the traction control is active, upshifts are delayed to increase your control of the vehicle. See Traction Control System (TCS) on page 4-6. While the Manual Paddle Shift gear selection system is active, the transmission will automatically downshift through the gears as the vehicle slows. The transmission will select second gear as the vehicle stops. From a stop, the vehicle will start from and hold second (2) gear unless the driver manually paddle shifts into a different gear or selects DRIVE (D). The driver can select ﬁrst (1) gear for maximum acceleration from a stop. 2-29 When using the Manual Paddle Shift Feature while in the SPORT MODE (S), the current gear will be displayed in the Driver Information (DIC), or the Head-Up Display (HUD), if the vehicle has either of these features. When the transmission gear does not respond to a shift change, the DIC will show an X over the gear display. When a requested shift is denied due to the speed restrictions shown, the DIC will momentarily show an X over the gear display and a chime will sound. If your vehicle has a Navigation system, see “Head-Up Display (HUD)” in the Index of the navigation manual. The Manual Paddle Shift system will not allow either an up-shift or a down-shift if the vehicle speed is too fast or too slow, nor will it allow a start from Fourth (4) or higher gear If up-shifting does not occur when needed, the vehicle speed will be limited to protect the engine. The transmission will also automatically down-shift as the vehicle slows down and comes to a stop. If the vehicle has a HUD, and the transmission gear does not respond to a shift change, then a chime will sound and the HUD will momentarily show an X over the gear display. Manual Paddle Shift operation is available for use with Cruise Control, see Cruise Control on page 3-11 for more information. 2-30 The vehicle speeds required for Manual Paddle Shift up-shifts depend on several vehicle inputs, which will vary the allowed up-shift speed by a few mph (km/h). (cid:129) Up-shifts to Fourth (4) gear require approximately 22 mph (35 km/h). (cid:129) Up-shifts to Fifth (5) gear require approximately 28 mph (45 km/h). (cid:129) Up-shifts to Sixth (6) gear require approximately 41 mph (65 km/h). To prevent damage to the powertrain, Manual Paddle downshifts to a lower gear cannot be done above certain speeds. The maximum speed allowed for downshifting of gears one (1) through fourth (4) are: Into Fourth (4) gear over 168 mph (270 km/h) Into Third (3) gear over 124 mph (200 km/h) Into Second (2) gear over 81 mph (130 km/h) Into First (1) gear over 45 mph (72 km/h). If the driver does not request an upshift as the engine speed approaches fuel shut off RPM, the engine speed will be limited to protect the engine. See Tachometer on page 3-34 for more information. Manual Transmission Operation This is the shift pattern for the six-speed manual transmission. Here is how to operate your transmission: FIRST (1): Press the clutch pedal and shift into FIRST (1). Then slowly let up on the clutch pedal as you press the accelerator pedal. You can shift into FIRST (1) when you are going less than 40 mph (64 km/h). If you come to a complete stop and it is hard to shift into FIRST (1), put the shift lever in NEUTRAL and let up on the clutch. Press the clutch pedal back down. Then shift into FIRST (1). 2-31 (cid:129) (cid:129) (cid:129) (cid:129) SECOND (2): Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND (2). Then, slowly let up on the clutch pedal as you press the accelerator pedal. THIRD (3), FOURTH (4), FIFTH (5) and SIXTH (6): Shift into THIRD (3), FOURTH (4), FIFTH (5) and SIXTH (6) the same way you do for SECOND (2). Slowly let up on the clutch pedal as you press the accelerator pedal. To stop, let up on the accelerator pedal and press the brake pedal. Just before the vehicle stops, press the clutch pedal and the brake pedal, and shift to NEUTRAL. NEUTRAL: Use this position when you start or idle your engine. Your shift lever is in NEUTRAL when it is centered in the shift pattern, not in any gear. REVERSE (R): To back up, press down the clutch pedal and shift into REVERSE (R). Just apply pressure to get the lever past FIFTH (5) and SIXTH (6) into REVERSE (R). Let up on the clutch pedal slowly while pressing the accelerator pedal. Your six-speed manual transmission has a feature that allows you to safely shift into REVERSE (R) while the vehicle is rolling at less than 3 mph (5 km/h). You will be locked out if you try to shift into REVERSE (R) while your vehicle is moving faster than 3 mph (5 km/h). Shift Speeds (Manual Transmission) {CAUTION: If you skip a gear when you downshift, you could lose control of your vehicle. You could injure yourself or others. Do not shift down more than one gear at a time when you downshift. 2-32 This chart shows when to shift to the next higher gear for the best fuel economy. One to Four Shift Light (Manual Transmission) Manual Transmission Recommended Shift Speeds in mph (km/h) Acceleration Shift Speed 2 to 3 4 to 5 3 to 4 1 to 2 5 to 6 15 (24) 25 (40) 40 (64) 45 (72) 50 (80) Engine All Engines If your engine speed drops below 900 rpm, or if the engine is not running smoothly, you should downshift to the next lower gear. You may have to downshift two or more gears to keep the engine running smoothly or for good engine performance. Notice: When shifting gears, do not move the shift lever around unnecessarily. This may damage the transmission. Shift directly into the next gear. When this light comes on, you can only shift from FIRST (1) to FOURTH (4) instead of FIRST (1) to SECOND (2). See One-to-Four Shift Light (Manual Transmission) on page 3-38 for more information. 2-33 Parking Brake The parking brake lever is located to the right of the center console. To set the parking brake, hold the brake pedal down. Pull the parking brake lever up. If the ignition is on, the brake system warning light will come on. To release the parking brake, hold the brake pedal down. Then push the release button in as you move the parking brake lever all the way down. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving. Downshifting (Manual Transmission) Do not downshift into the gear shown below at a speed greater than shown in the table: FIRST (1) SECOND (2) THIRD (3) FOURTH (4) 50 mph (80 km/h) 74 mph (119 km/h) 101 mph (163 km/h) 130 mph (209 km/h) If you skip more than one gear when you Notice: downshift, or if you race the engine when you release the clutch pedal while downshifting, you could damage the engine, clutch, driveshaft or the transmission. Do not skip gears or race the engine when downshifting. The six-speed transmission has a spring that centers the shift lever near THIRD (3) and FOURTH (4). This spring helps you know which gear you are in when you are shifting. Be careful when shifting from FIRST (1) to SECOND (2) or downshifting from SIXTH (6) to FIFTH (5). The spring will try to pull the shift lever toward FOURTH (4) and THIRD (3). Make sure you move the lever into SECOND (2) or FIFTH (5). If you let the shift lever move in the direction of the pulling, you may end up shifting from FIRST (1) to FOURTH (4) or from SIXTH (6) to THIRD (3). 2-34 Shifting Into PARK (P) (Automatic Transmission) Leaving Your Vehicle With the Engine Running (Automatic Transmission) {CAUTION: {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. 1. Hold the brake pedal down with your right foot and set the parking brake. See Parking Brake on page 2-34 for more information. 2. Move the shift lever into PARK (P) by holding in the button on the lever and pushing the lever all the way toward the front of the vehicle. 3. Press the Acc. button (ignition switch) to turn the engine off. It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into PARK (P), hold down the regular brake pedal. See if you can move the shift lever away from PARK (P) without ﬁrst pulling it toward you. If you can, it means that the shift lever was not fully locked into PARK (P). 2-35 The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9 volt) battery. If your vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 5-46 To shift out of PARK (P) use the following: 1. Apply the brake pedal. 2. Then press the shift lever button. 3. Move the shift lever to the desired position. If you still are unable to shift out of PARK (P): 1. Fully release the shift lever button. 2. While holding down the brake pedal, press the shift lever button again. 3. Move the shift lever to the desired position. If you still cannot move the shift lever from PARK (P), consult your dealer/retailer or a professional towing service. Torque Lock (Automatic Transmission) If you are parking on a hill and you do not shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see “Shifting Into PARK (P)” listed previously in this section. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the transmission parking pawl, so you can pull the shift lever out of PARK (P). Shifting Out of PARK (P) This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: Prevent shifting out of PARK (P) unless the vehicle is running or in Accessory mode and the regular brake pedal is applied. 2-36 Parking Your Vehicle (Manual Transmission) Before you get out of your vehicle, move the shift lever into REVERSE (R) and ﬁrmly apply the parking brake. Once the shift lever has been placed into REVERSE (R) with the clutch pedal pressed in, you can turn the ignition off and release the clutch. Parking Over Things That Burn {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:129) The exhaust system sounds strange or different. (cid:129) Your vehicle gets rusty underneath. (cid:129) Your vehicle was damaged in a collision. (cid:129) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:129) Repairs were not done correctly. (cid:129) Your vehicle or the exhaust system has been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:129) Drive it only with all the windows down to blow out any CO; and (cid:129) Have your vehicle ﬁxed immediately. 2-37 Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-37. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-19. It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into PARK (P) (Automatic Transmission) on page 2-35. 2-38 Mirrors Automatic Dimming Rearview Mirror with OnStar® and Compass The vehicle may have an automatic dimming rearview mirror with OnStar®, a compass and map lamps. Three OnStar® buttons are at the bottom of the mirror. See OnStar® System on page 2-45 for more information on the services OnStar® provides. Mirror Operation The mirror automatically changes to reduce glare from headlamps behind you. A time delay feature prevents rapid changing from the day to night positions while driving under lights and through traffic. P(On/Off): The automatic dimming feature is activated when the vehicle is started. The automatic dimming feature is turned on or off by pressing this button located on the lower part of the mirror. Press and hold the button for up to three seconds to turn this feature on or off. T(Indicator Light): This light will turn on when the automatic dimming feature is active. Map Lamps The mirror has map lamps located at the bottom of the mirror. To manually turn the lamps on or off, press the button next to each lamp. Compass Operation The mirror has an eight-point compass display in the bottom of the mirror face. When the ignition and the compass feature are on, the compass will show two character boxes for approximately two seconds. After two seconds, the mirror will display the current compass heading. For example, NE is displayed for north-east. Compass Calibration If after two seconds the display does not show a compass heading, there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, note pad holder or similar object. If the letter C appears in the compass window, the compass needs calibration. The mirror compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. The compass can be placed in calibration mode by pressing and holding the left map light button until a C appears on the compass display. 2-39 Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. If the mirror is not adjusted for compass variance, your compass could give false readings. The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as a long distance, cross-country trip, it will be necessary to adjust the compass variance. To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the zone map that follows. 2-40 2. Press and hold the on/off button until a Z and a zone number appears on the display. The compass is now in zone mode. 3. Once the zone number appears on the display, press the on/off button quickly until you reach the correct zone number. Stop pressing the button and the mirror will return to normal operation. If C appears in the compass window, the compass may need calibration. See “Compass Calibration” listed previously. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Automatic Dimming Rearview Mirror with Compass If the vehicle has this feature, an automatic dimming mirror automatically dims to the proper level to minimize glare at night from lights behind your vehicle. The mirror also includes a compass display in the upper right corner of the mirror face. P(On/Off): This is the on/off button. Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on each time the ignition is started. A light near the on/off button will come on to indicate the automatic dimming is on. Press the on/off button for about six seconds to manually turn the automatic dimming function on or off. Compass Display Press the on/off button, located to the far left, brieﬂy to turn the compass display on or off. If the display reads CAL, the compass needs to be calibrated. For more information, see “Compass Calibration” later in this section. To adjust between Fahrenheit and Celsius: 1. Press and hold the on/off button for approximately four seconds until either a ﬂashing °F, or °C appears. 2. Press the button again to change the display to the desired unit of measurement. After approximately four seconds of inactivity, the new unit will be locked in and the compass/temperature display will return. If an abnormal temperature reading is displayed for an extended period of time, please consult your dealer/retailer. Under certain circumstances, a delay in updating the temperature is normal. 2-41 Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, the mirror’s compass could give false readings. The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will also be necessary to adjust for compass variance. To adjust for compass variance do the following: 1. Find your current location and variance zone number on the following zone map. 2-42 2. Press and hold the on/off button until a Z and a zone number appears in the display. The compass is now in zone mode. 3. Keep pressing the on/off button until the desired zone number appears in the display. Release the button. After approximately four seconds of inactivity, the new zone number will be locked in and the compass/temperature display will return. 4. Calibrate the compass as described below. Compass Calibration The compass may need calibration if one of the following occurs: (cid:129) After approximately ﬁve seconds, the display does not show a compass heading (N for North, for example), there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder, or a similar magnetic item. The compass does not display the correct heading and the compass zone variance is set correctly. In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, push the on/off button for approximately 12 seconds or until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Outside Power Heated Mirrors The controls for the outside power mirrors are located on the driver’s door. Move the top selector control to the left or right to select either the driver’s or passenger’s mirror. To adjust the direction of the mirror, use the arrows on the round four-way control. Adjust each outside mirror so that a little of the vehicle and the area behind it can be seen while sitting in a comfortable, driving position. Keep the control in the center position when not adjusting either outside mirror. 2-43 (cid:129) If the vehicle has the memory feature, a preferred mirror position can be stored. See Memory Seat, Mirrors and Steering Wheel on page 1-4. Both mirrors are heated to rid them of snow, ice, or condensation. They will heat when the rear window defogger is turned on. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-25. Both mirrors can manually be folded inward by pulling them toward the vehicle. This feature may be useful when going through a car wash or a conﬁned space. Push the mirrors away from the vehicle, to the normal position, before driving. Outside Automatic Dimming Mirror If your vehicle has this feature, the driver’s side outside mirror will adjust for the glare of headlamps behind you. This feature is controlled by the on and off setting on the inside mirror. Outside Convex Mirror {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. The passenger side mirror is convex. A convex mirror’s surface is curved so more can be seen from the driver seat. It also makes things, like other vehicles, look farther away than they really are. 2-44 OnStar® System OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar button and they can contact Roadside Service for you. OnStar service is provided to you subject to the OnStar Terms and Conditions. You may cancel your OnStar service at any time by contacting OnStar. A complete OnStar Owner’s Guide and the OnStar Terms and Conditions are included in the vehicle’s OnStar Subscriber glove box literature. For more information, visit onstar.com or onstar.ca, contact OnStar at 1–888–4–ONSTAR (1–888–466–7827) or TTY 1–877–248–2080, or press the OnStar button to speak with an OnStar advisor 24 hours a day, 7 days a week. Not all OnStar features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar services and system limitations, see the OnStar Owner’s Guide in your glove box or visit onstar.com. OnStar Services For new vehicles with OnStar, the Safe & Sound Plan, or the Directions & Connections Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions & Connections Plan. For more information, press the OnStar button to speak with an advisor. Some OnStar services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar. 2-45 OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To ﬁnd out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar Owner’s Guide for more information (only available in the continental U.S.). Available Services with Safe & Sound Plan (cid:129) Automatic Notiﬁcation of Airbag Deployment (cid:129) Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) Link to Emergency Services (cid:129) Roadside Assistance (cid:129) Stolen Vehicle Location Assistance (cid:129) AccidentAssist (cid:129) Remote Door Unlock/Vehicle Alert (cid:129) OnStar Vehicle Diagnostics (cid:129) GM Goodwrench® On Demand Diagnostics (cid:129) OnStar Hands-Free Calling with 30 complimentary minutes (cid:129) OnStar Virtual Advisor (U.S. Only) Available Services included with Directions & Connections Plan (cid:129) All Safe and Sound Plan Services (cid:129) Driving Directions - Advisor delivered or OnStar Turn-by-Turn Navigation (If equipped) (cid:129) RideAssist Information and Convenience Services 2-46 (cid:129) (cid:129) How OnStar Service Works Your vehicle’s OnStar system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar Call Center at the time of an OnStar button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar Hands-Free Calling, your vehicle also sends OnStar your GPS location so that we can provide you with location-based services. OnStar service cannot work unless your vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless you are in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. Location information about your vehicle is only available if the GPS satellite signals are unobstructed and available. Your vehicle must have a working electrical system (including adequate battery power) for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility Increase the radio volume if you cannot hear the OnStar advisor. If the light next to the OnStar buttons is red, this means that your system is not functioning properly and should be checked by a dealer/retailer. If the light appears clear (no light is appearing), your OnStar subscription has expired. You can always press the OnStar button to conﬁrm that your OnStar equipment is active. 2-47 Universal Home Remote System Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held radio-frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The FCC Grant of Equipment Authorization Certiﬁcate number is KOBGTV06A. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. 2-48 The Canadian Registration ID number is 3521A-GTV06A. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Universal Home Remote System Operation (With Three Round LED) Your vehicle may have the Universal Home Remote System. If there are three round Light Emitting Diode (LED) indicator lights above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use this system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter. Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming. You only need the original remote control transmitter for Fixed Code programming. It is also recommended that upon the sale or lease termination of the vehicle, the programmed buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, it is advised to park outside of the garage. Be sure that people and objects are clear of the garage door or security device you are programming. Programming Universal Home Remote — Rolling Code If you have questions or need help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. To program up to three devices: 1. From inside the vehicle, press the two outside buttons at the same time for one to two seconds, and immediately release them. 2-49 3. Immediately return to your vehicle. Press and hold the Universal Home Remote button that you would like to use to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. You may need to hold the button from ﬁve to 20 seconds. 4. Immediately, within one second, release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 5. Press and release the same button again. The garage door should move, conﬁrming that programming is successful and complete. 2. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button. After you press this button, you will have 30 seconds to complete the following steps. To program another Rolling Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1-5, choosing a different function button in Step 3 than what you used for the garage door opener. If these instructions do not work, you probably have a Fixed Code garage door opener. Follow the Programming instructions that follow for a Fixed Code garage door opener. 2-50 To program up to three devices: Programming Universal Home Remote — Fixed Code If you have questions or need help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold before 1996 are Fixed Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. 1. To verify if you have a Fixed Code garage door opener, remove the battery cover on your hand held transmitter supplied by the manufacturer of your garage door opener motor. If you see a row of dip switches similar to the graphic above, you have a Fixed Code garage door opener. If you do not see a row of dip switches, return to the previous section for Programming Universal Home Remote – Rolling Code. 2-51 Your hand held transmitter may have between eight to 12 dip switches depending on the brand of transmitter. Your garage door opener receiver (motor head unit) may also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head and hand held transmitter are different, or if the dip switch settings are different, use the dip switch settings on the motor head unit to program your Universal Home Remote. The motor head dip switch settings can also be used when you do not have the original hand held transmitter. Example of Eight Dip Switches with Two Positions 2-52 Example of Eight Dip Switches with Three Positions Your panel of switches may not appear exactly as they do in the examples above, but they should be similar. The switch positions on your hand-held transmitter may be labeled, as follows: (cid:129) A switch in the up position may be labeled as “Up,” “+,” or “On.” (cid:129) A switch in the down position may be labeled as “Down,” “−,” or “Off.” (cid:129) A switch in the middle position may be labeled as “Middle,” “0,” or “Neutral.” 2. Write down the eight to 12 switch settings from left to right as follows: (cid:129) When a switch is in the up position, write “Left.” (cid:129) When a switch is in the down position, write “Right.” If a switch is set between the up and down position, write “Middle.” The switch settings that you wrote down in Step 2 will now become the button strokes you enter into the Universal Home Remote in Step 4. Be sure to enter the switch settings that you wrote down in Step 2, in order from left to right, into the Universal Home Remote, when completing Step 4. 3. From inside your vehicle, ﬁrst ﬁrmly press all three buttons at the same time for about three seconds. Release the buttons to put the Universal Home Remote into programming mode. 4. The indicator lights will blink slowly. Enter each switch setting from Step 2 into your vehicle’s Universal Home Remote. You will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows: If you wrote “Left,” press the left button in the vehicle. If you wrote “Right,” press the right button in the vehicle. If you wrote “Middle,” press the middle button in the vehicle. 2-53 (cid:129) (cid:129) (cid:129) (cid:129) 5. After entering all of the switch positions, again, ﬁrmly press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button you would like to use to control the garage door until the garage door moves. The indicator light above the selected button should slowly blink. You may need to hold the button from ﬁve to 55 seconds. 7. Immediately release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 8. Press and release the same button again. The garage door should move, conﬁrming that programming is successful and complete. To program another Fixed Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1-8, choosing a different button in Step 6 than what you used for the garage door opener. Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted. Reprogramming Universal Home Remote Buttons You can reprogram any of the three buttons by repeating the instructions. Erasing Universal Home Remote Buttons You should erase the programmed buttons when you sell or terminate your lease. To erase either Rolling Code or Fixed Code on the Universal Home Remote device: 1. Press and hold the two outside buttons at the same time for approximately 20 seconds, until the indicator lights, located directly above the buttons, begin to blink rapidly. 2. Once the indicator lights begin to blink, release both buttons. The codes from all buttons will be erased. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 7-6. 2-54 Storage Areas Glove Box To open the glove box, lift up on the lever. Use the key to lock and unlock. The glove box has a light inside. Cupholder(s) There are two cupholders located on the center console next to the shift lever. To access, place your thumb on the left side of the lid and slide the handle to the right. Center Console Storage To use this storage area, pull up the lid on the driver’s side front edge of the console and swing it to the passenger side. Floor Mats The ﬂoor mats are designed to remain in position under your feet and out of reach of the accelerator pedal. The driver side ﬂoor mat is held in place by two locator pins and the passenger side is held in place by one. Make sure that the driver side ﬂoor mat is properly placed on the ﬂoor so that it does not block the movement of the accelerator pedal. To remove a ﬂoor mat, pull up on the rear of the mat to disconnect it from the locator pins. To reinstall the ﬂoor mats, line up the openings in the ﬂoor mat over the locator pins and push it down into place. 2-55 For Z06 models the right rear compartment stores the battery and cannot be used for storage. Notice: Do not store heavy or sharp objects in the rear storage compartments located in the hatch/trunk area. If you do, the objects could damage the underbody. Rear Trunk Partition For vehicles with the power convertible top option only, there is a trunk partition to keep cargo from getting in the way of the convertible top. The trunk partition must be in place for the top to move. If the trunk partition is not properly in place the ATTACH TRUNK PARTITION Driver Information Center (DIC) message will display and you will not be able to remove the convertible top. See DIC Warnings and Messages on page 3-55 for more information. The trunk partition is a ﬂat carpeted board with a horizontal ﬂap that can be attached to the top of the trunk to divide the storage compartment or stored ﬂat when not in use. Rear Storage Area There are two rear storage compartments in the ﬂoor of the rear hatch/trunk area. Convertible shown, Coupe similar Your vehicle has two storage compartment lids. To access a storage compartment, pull up to open the lid. The lids cannot be removed. 2-56 Cargo Cover If your vehicle has this feature, the security shade can provide hidden storage in the rear area of the vehicle. The shade is also helpful in blocking the glare from the removable roof when it is stored in the rear compartment. Using the Cargo Cover 1. Hook the elastic loops on the front corners (A) of the shade to the T-nuts located on the front corners of the rear hatch frame. 2. Hook the elastic loops on the rear corners (B) of the shade to the hooks recessed inside the rear hatch frame, near the rear corners. 2-57 Pull the divider up and snap it onto the snaps on both sides of the trunk. Convenience Net Your vehicle may have a convenience net in the rear of the vehicle. Put small loads behind the net. The net is not for heavier loads. Store them as far forward as you can. 4. Push the loop to the top of the striker (base plate). 3. Grasp the loop at the rear center of the shade and wrap it around the striker assembly. Roof Panel The vehicle may have a removable roof panel. Follow the procedures listed when removing or installing it. 2-58 Removing the Roof Panel {CAUTION: Do not try to remove a roof panel while the vehicle is moving. Trying to remove the roof panel while the vehicle is moving could cause an accident. The panel could fall into the vehicle and cause you to lose control, or it could ﬂy off and strike another vehicle. You or others could be injured. Remove the roof panel only when the vehicle is parked. Until you are sure you can remove the panel alone, have someone help you. Notice: If you drop or rest a roof panel on its edges, the roof panel, paint and/or weatherstripping may be damaged. Always place the roof panel in the stowage receivers after removing it from the vehicle. 1. Park on a level surface and set the parking brake. Shift an automatic transmission into PARK (P). Shift a manual transmission into NEUTRAL. 2. Make sure the ignition is off. 3. Lower both sun visors. 4. Open the rear hatch and remove any items that may interfere with proper storage of the roof panel. 5. Lower the windows. There are two release latches on the front of the roof panel and one rear release latch on the back of the roof panel. 6. To unlock the release latches on the front of the roof panel, grasp each handle with your ﬁngers and pull it outward. 2-59 7. To unlock the rear of the roof panel’s rear release latch, press the back of the release handle (B). Then press the button on the front of the release handle, (A) with your thumb. The driver’s side handle moves toward the driver’s door. The passenger’s side handle moves toward the passenger’s door. Pull down the latch lever with your ﬁngers. 8. Stand on one side of the vehicle, and if necessary, have someone stand on the other side. Together, carefully lift the front edge of the roof panel up and forward. 9. When the roof panel is loosened from the vehicle, one person should grasp the roof panel as close to the center as possible and lift it away from the vehicle. 2-60 Storing the Roof Panel 1. Turn the roof panel so that the front edge of the panel is facing the storage area. {CAUTION: If a roof panel is not stored properly, it could be thrown about the vehicle in a crash or sudden maneuver. People in the vehicle could be injured. Whenever you store a roof panel in the vehicle, always be sure that it is stored securely in the proper location. If you drop or rest a roof panel on its Notice: edges, the roof panel, paint and/or weatherstripping may be damaged. Always place the roof panel in the stowage receivers after removing it from the vehicle. 2. Insert the roof panel so that the outside front edges line up between the receiver covers. Push forward on the roof panel until it stops. 3. Gently place the roof panel down so that the back pins on the roof panel drop into the receivers in the back of the storage area. Press down ﬁrmly to seat the pins in the receivers. 2-61 Installing the Roof Panel {CAUTION: An improperly attached roof panel may fall into or ﬂy off the vehicle. You or others could be injured. After installing the roof panel, always check that it is ﬁrmly attached by pushing up on the underside of the panel. Check now and then to be sure the roof panel is ﬁrmly in place. If you drop or rest a roof panel on its Notice: edges, the roof panel, paint and/or weatherstripping may be damaged. Always place the roof panel in the stowage receivers after removing it from the vehicle. In most cases, it makes it easier if two people re-install the roof panel. 1. Park on a level surface and set the parking brake. Shift an automatic transmission into PARK (P). Shift a manual transmission into NEUTRAL. 2. Check that the front release latches and the rear release latch on the vehicle’s roof opening are in their opened positions before attempting to install the roof panel. 3. If the roof panel is stored in the rear storage area of the vehicle, grasp the rear edge of the roof panel with both hands and gently lift it up and remove it from the storage area. 4. Carefully place the roof panel over the top of the vehicle. 5. Position the rear edge of the roof panel to the weatherstrip on the back of the roof opening. Then align and ﬁt the pins at the rear of the roof panel inside the openings in the rear overhead weatherstrip. Gently lower the front edge of the roof panel to the front of the roof opening. 2-62 6. Turn the front release handles inward so that they latch to the closed position. Convertible Top Convertible Top (Manual) For care and cleaning of the convertible top, see Convertible Top on page 5-91 under “Service and Appearance Care”. High pressure car washes may cause water to enter the vehicle. If the vehicle has this feature, the following procedures explain the proper operation of the manual convertible top. 7. Push up on the handle of the rear roof release handle to latch its hook in the closed position. 8. Push and pull the roof panel up and down and side-to-side to ensure the roof panel is securely installed. 2-63 Notice: Lowering the convertible top when there are objects in the storage area could damage it or break the glass rear window. Always verify that no objects are in the storage area before lowering the convertible top. Notice: Lowering the top if it is damp, wet, or dirty can cause stains, mildew, and damage to the inside of your vehicle. Dry off the top before lowering it. Notice: weather (0°F/-18°C or lower), you may damage top components. Do not lower the top in cold weather. Notice: while the vehicle is in motion, you could damage the top or the top mechanism. The repairs would not be covered by your warranty. Always put an automatic transmission in PARK (P) or a manual transmission in NEUTRAL before raising or lowering the convertible top. If you lower the top on your vehicle in cold If you raise or lower the convertible top The parts of the manual convertible top that are used when lowering and raising it are: A. Front Edge of the Convertible Top B. Rear Edge of the Convertible Top C. Tonneau Cover Notice: Leaving the convertible top down and exposing the interior of your vehicle to outdoor conditions may cause damage. Always close the convertible top if leaving your vehicle outdoors. 2-64 Lowering the Manual Convertible Top 1. Park on a level surface. Shift an automatic transmission into PARK (P) and set the parking brake. Shift a manual transmission into NEUTRAL and set the parking brake. 2. Make sure the ignition is off. 3. Make sure the trunk is closed. 4. The convertible top front latch, located above the inside rearview mirror, must be unlocked. Pull the convertible top front latch down and turn it clockwise to unlock it. 5. Lift upward on the front edge (A) of the convertible top off of the windshield frame. Then lift upward on the rear edge (B) of the convertible top so it is vertical to the tonneau cover (C). The front edge (A) and rear edge (B) should be straight up. 2-65 After pressing the release button, the driver’s and passenger’s door glass should retract to the full-down position. If the vehicle has lost battery power, the tonneau cover (C) can still be opened using the manual release cable. The tonneau cover emergency manual release cable is located underneath the carpeting behind the passenger’s seat head restraint, on the underside forward edge of the tonneau cover. To access the cable, lift and pull back the carpeting. Also, see Hatch on page 2-14 for information on the emergency trunk release handle. If you lower the convertible top into the Notice: storage compartment and the rear edge of the top is not in the full-down position, you could damage the top. Always verify that the rear edge of the convertible top is in the full-down position before lowering the top into the storage compartment. 6. Tilt the driver’s seatback forward and press the tonneau cover release button located on the underside of the tonneau cover (C) behind the driver’s seat. Then raise the tonneau cover (C). If the tonneau cover does not release and three chimes are heard, check to make sure the trunk lid is closed. Also, the cover will not release if the vehicle alarm is armed. 2-66 7. Pull the cable to release the tonneau cover. 8. Push forward on the front edge (A) of the convertible top to allow the rear edge (B) of the convertible top to be moved to its full-down position. 2-67 Raising the Manual Convertible Top 1. Park on a level surface. Shift an automatic transmission into PARK (P) and set the parking brake. Shift a manual transmission into NEUTRAL and set the parking brake. 2. Lower both windows. 3. Make sure the ignition is off. 4. Tilt the driver’s seat forward and press the tonneau cover release button, or use the manual release cable if battery power has been lost. See Step 6 under “Lowering the Manual Convertible Top” earlier in this section. After pressing the release button, the driver’s and passenger’s door glass should retract to the full-down position, if they have not already been lowered. 5. Lift the tonneau cover. 9. Then move the top rearward to its fully-stored position. 10. After the top is stored, apply one even push on the center of the front edge (A) of the convertible top to assure that the top is fully retracted. 11. Close the tonneau cover (B) by pressing down on it with a swift, ﬁrm motion. 2-68 6. Pull the convertible top up by ﬁrmly gripping the front edge (A) near the center and applying a brisk upward and forward motion to get the top in the full-up position. 7. Lift the rear edge (B) of the convertible top to its full-up position by ﬁrst raising the front edge (A). 8. Close the tonneau cover (C) by pushing it down with a swift, ﬁrm motion. 9. Lower the rear edge (B) of the convertible top by ﬁrst slightly pushing the front edge (A) of the convertible top forward. 10. Push the front edge (A) of the convertible top down from the outside of the vehicle, or pull the front edge (A) of the convertible top down from the center pull-down handle located in the inside of the vehicle. 2-69 To operate the power convertible top use the following steps. Notice: Leaving the convertible top down and exposing the interior of your vehicle to outdoor conditions may cause damage. Always close the convertible top if leaving your vehicle outdoors. Notice: Lowering the convertible top when there are objects in the storage area could damage it or break the glass rear window. Always verify that no objects are in the storage area before lowering the convertible top. Notice: Lowering the top if it is damp, wet, or dirty can cause stains, mildew, and damage to the inside of your vehicle. Dry off the top before lowering it. Notice: weather (0°F/-18°C or lower), you may damage top components. Do not lower the top in cold weather. If you lower the top on your vehicle in cold 11. Pull the top front latch handle down and turn it counterclockwise to lock the convertible top. Convertible Top (Power) For care and cleaning of the convertible top see Convertible Top on page 5-91 under “Service and Appearance Care”. High pressure car washes may cause water to enter the vehicle. 2-70 If you raise or lower the convertible top Notice: while the vehicle is in motion, you could damage the top or the top mechanism. The repairs would not be covered by your warranty. Always put an automatic transmission in PARK (P) or a manual transmission in NEUTRAL before raising or lowering the convertible top. Lowering the Power Convertible Top 1. Park on a level surface. Start the engine. Shift an automatic transmission into PARK (P) and set the parking brake. Shift a manual transmission into NEUTRAL, and set the parking brake. 2. Make sure the trunk is closed and the rear trunk partition in the rear storage area is in the fastened upright position, and that no objects are forward of the divider. See “Rear Trunk Partition” under Rear Storage Area on page 2-56. 3. Release the convertible top front latch, located above the inside rearview mirror, by pulling and turning it clockwise toward the driver’s door. Push upward on the front edge. The windows will automatically lower. 2-71 If you raise or lower the convertible top Raising the Power Convertible Top Notice: while the vehicle is in motion, you could damage the top or the top mechanism. The repairs would not be covered by your warranty. Always put an automatic transmission in PARK (P) or a manual transmission in NEUTRAL before raising or lowering the convertible top. 1. Park on a level surface. Start the engine. Shift an automatic transmission into PARK (P) and set the parking brake. Shift a manual transmission into NEUTRAL and set the parking brake. 2. Make sure the trunk lid is closed and the rear trunk partition in the rear storage area is in the fastened upright position, and that no objects are forward of the divider. See “Rear Trunk Partition” under Rear Storage Area on page 2-56. 3. Push and hold the top of the power convertible top button. The top will raise and the windows will lower if they were in the raised position. A chime will sound when the top is raised completely. 4. Push and hold the bottom of the power convertible top button, located to the left of the steering wheel, on the instrument panel. The windows will automatically lower and the convertible top will lower into the rear of the vehicle. A chime will sound when the convertible top has lowered completely. If the radio is on the sound may be muted for a brief time due to a new audio system equalization being loaded. If the convertible top is operated multiple times, the engine should be running to prevent drain on the vehicle’s battery. Under certain conditions, the Driver Information Center (DIC) may display a message regarding the power convertible top. See DIC Warnings and Messages on page 3-55 for more information. 2-72 4. After the convertible top is completely raised, release the power convertible top button. 5. Pull the convertible front top latch down and turn it counterclockwise to lock the convertible top. If the vehicle has lost power, the convertible top can still be raised by releasing pressure on the hydraulic pump, located under the passenger’s side of the tonneau cover, by using the following steps. The carpet liner on the passenger’s side must be pulled back to access the hydraulic pump. Manual operation of the power convertible top cannot be attempted for ﬁve minutes from the last time the convertible top button was pressed if the top is not completely stowed, with the top down and the tonneau latched, or closed, with the front top latch locked in place, at the time the convertible top button was released. If the radio is on the sound may be muted for a brief time due to a new audio system equalization being loaded. 2-73 Be careful when opening the tonneau cover by hand. If the tonneau cover is opened quickly, damage can occur to the hinging mechanism, which can prevent

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2008 Chevrolet Corvette Owners Manual