0 Always read the instructions on the cleaner label.
Clean up stains as soon as you can -- before they set. Use a clean cloth or sponge, and change to a clean area often. A soft brush may be used if stains are stubborn. 0 Use solvent-type cleaners in a well-ventilated area
only. If you use them, don’t saturate the stained area. If a ring forms after spot cleaning, clean the entire area immediately or it will set.
6-56
Using Foam-Type Cleaner on Fabric
Vacuum and brush the area to remove any loose dirt. Always clean a whole trim panel or section. Mask surrounding trim along stitch or welt lines. Mix Multi-Purpose Powdered Cleaner following the directions on the container label. Use suds only and apply with a clean sponge. Don’t saturate the material. Don’t rub it roughly. As soon as you’ve cleaned the section, use a sponge to remove the suds. Rinse the section with a clean, wet sponge. Wipe off what’s left with a slightly damp paper towel or cloth. Then dry it immediately with a blow dryer or a heat lamp.
NOTICE: Be careful. A blow dryer or a heat lamp may scorch the fabric.
0 Wipe with a clean cloth.
Using Solvent-Type Cleaner on Fabric First, see if you have to use solvent-type cleaner at all. Some spots and stains will clean off better with just water and mild soap. If you need to use a solvent: 0 Gently scrape excess soil from the trim material with a clean, dull knife or scraper. Use very little cleaner, light pressure and clean cloths (preferably cheesecloth). Cleaning should start at the outside of the stain, “feathering” toward the center. Keep changing to a clean section of the cloth. When you clean a stain from fabric, immediately dry the area with a blow dryer to help prevent a cleaning ring. (See the previous NOTICE.)
Fabric Protection Your Corvette has upholstery and carpet that has been treated with Scotchgard” Fabric Protector, a 3M product. Scotchgard TM protects fabrics by repelling oil and water, which are the carriers of most stains. Even with this protection, you still need to clean your upholstery and carpet often to keep it looking new. Further information on cleaning is available by calling 1-800-433-3296 (in Minnesota, 1-800-642-6167).
Special Cleaning Problems Greasy or Oily Stains Stains caused by grease, oil, butter, margarine, shoe polish, coffee with cream, chewing gum, cosmetic creams, vegetable oils, wax crayon, tar and asphalt can be removed as follows:
Carefully scrape off excess stain. Follow the solvent-type instructions described earlier. Shoe polish, wax crayon, tar and asphalt will stain if left on a vehicle seat fabric. They should be removed as soon as possible. Be careful, because the cleaner will dissolve them and may cause them to spread.
Non-Greasy Stains Stains caused by catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, wine, vomit, urine and blood can be removed as follows:
Carefully scrape off excess stain, then sponge the soiled area with cool water. If a stain remains, follow the foam-type instructions described earlier.
6-57
If an odor lingers after cleaning vomit or urine, treat the area with a waterhaking soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml) of lukewarm water. If needed, clean lightly with solvent-type cleaner.
Combination Stains Stains caused by candy, ice cream, mayonnaise, chili sauce and unknown stains can be removed as follows: Carefully scrape off excess stain, then clean with cool water and allow to dry. If a stain remains, clean it with solvent-type cleaner.
Cleaning Vinyl Use warm water and a clean cloth.
Rub with a clean, damp cloth to remove dirt. You may have to do it more than once. Things like tar, asphalt and shoe polish will stain if you don’t get them off quickly. Use a clean cloth and a GM VinylLeather Cleaner or equivalent product.
Cleaning Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap. 0 For stubborn stains, use a GM Vinylkeather Cleaner
or equivalent product.
0 Never use oils, varnishes, solvent-based or abrasive cleaners, furniture polish or shoe polish on leather. 0 Soiled leather should be cleaned immediately. If dirt
is allowed to work into finish, it can harm the leather.
Cleaning Soft-Touch Surfaces Use only mild soap and water to clean the Soft-Touch paint surfaces in your Corvette. Cleaning Dulso-Coated Moldings These moldings are around the hatch opening in your Corvette’s rear area. 0 When lightly soiled, wipe with a sponge or soft
lint-free cloth dampened with water.
0 When heavily soiled, use warm soapy water.
6-58
You can remove scratches from a Dulso-coated molding by wiping briskly with the solvent-type cleaner described earlier. If a ring forms, repeat the procedure over a larger area, feathering toward the center of the ring. If the ring still remains, wipe the whole molding. Cleaning the Top of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Cleaning Speaker Covers Vacuum around a speaker cover gently, so that the speaker won’t be damaged. If something gets on one of them, follow the steps earlier under “Using Solvent-Type Cleaner on Fabric.” Use as little solvent as you can.
Care of Safety Belts Keep belts clean and dry.
Glass Glass should be cleaned often. GM Glass Cleaner (GM Part No. 1050427) or a liquid household glass cleaner will remove normal tobacco smoke and dust films. Don’t use abrasive cleaners on glass, because they may cause scratches. Avoid placing decals on the inside rear window, since they may have to be scraped off later. If abrasive cleaners are used on the inside of the rear window, an electric defogger element may be damaged. Any temporary license should not be attached across the defogger grid.
6-59
Cleaning the Outside of the Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with GM Windshield Cleaner, Bon-Ami Powder@ (GM Part No. 1050011). The windshield is clean if beads do not form when you rinse it with water. If you use a glass treatment or conditioner containing ethyl alcohol or ethyl sulfate on your glass, be sure to remove the acrylic roof panel, if so equipped. These products may darnage the panel. Clean the blade by wiping vigorously with a cloth soaked in full strength windshield washer solvent. Then rinse the blade with water. Wiper blades should be checked on a regular basis and replaced when worn.
Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth at least every six months. During very cold, damp weather more frequent application may be required. (See “Recommended Fluids and Lubricants” in the Index.) Cleaning a Removable Roof Panel Special care is necessary when cleaning, removing and/or storing the roof panel.
Flush with water to remove dust and dirt, then dry the panel. Clean the panel with GM Glass Cleaner. Leave the cleaner on the panel for one minute, then wipe the panel with a soft, lint-free cloth. Don’t use abrasive cleaning materials.
If water drops are frequently allowed to dry on the roof panel, impurities in the water will adhere to the top. These impurities may destroy the finish. When the panel gets wet, you should dry it o€f.
6-60
NOTICE: Do not use a glass treatment or conditioner containing ethyl alcohol or ethyl sulfate on the roof panel. These products may damage the panel.
Cleaning the Outside of Your Corvette The paint finish on your vehicle provides beauty, depth of color, gloss retention and durability. Washing Your Vehicle The best way to preserve your vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Don’t wash your vehicle in the direct rays of the sun. Don’t use strong soaps or chemical detergents. Use liquid hand, dish or car washing (mild detergent) soaps. Don’t use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on
the surface, or they could stain. Dry the finish with a soft, clean chamois or a 100% cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter your vehicle.
I NOTICE:
Conveyor systems on some automatic car washes may damage a Corvette. They may not have enough clearance for the undercarriage or for the extra wide rear tires on ZR-1 models. Check with the manager before using a car wash.
Finish Care Occasional waxing or mild polishing of your Corvette by hand may be necessary to remove residue from the paint finish. You can get GM approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.)
6-6 1
Your Corvette has a “basecoatklearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoatklearcoat paint finish.
Machine compounding or aggressive polishing on a basecoatlclearcoat paint finish may dull the finish or leave swirl marks.
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc. can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your Corvette garaged or covered whenever possible.
Cleaning Your Convertible Top Your convertible top should be cleaned often. If you use an automatic car wash, use one with water jets and hanging cloths. When you hand wash the top, do it in partial shade. Vacuum away any dust and other material. Use a mild soap, lukewarm water and a soft sponge. A chamois or cloth may leave lint on the top, and a brush can chafe the threads in the top fabric. Don’t use detergents, harsh cleaners, solvents or bleaching agents. When you clean the top, put one hand under it to support it. Wet the entire vehicle and wash the top evenly to avoid spots or rings. Let the soap remain on the fabric for a few minutes. When the top is really dirty, use a mild foam-type cleaner. Thoroughly rinse the entire vehicle, then let the top dry in direct sunlight. To protect the convertible top: 0 After you wash the vehicle, make sure the top is
completely dry before you lower it.
0 Don’t get any cleaner on the vehicle’s painted finish;
it could leave streaks.
0 If you decide to go through an automatic car wash,
ask the manager if the equipment could damage your top.
6-62
Cleaning and Storage of Your Hardtop The optional hardtop has the same durable finish as the painted surfaces of your Corvette. You can wash, polish and wax it. If you store the hardtop for a long time, keep it covered in a dry place. Apply silicone grease to all the weatherstrips. Engine Cleaning Use care when cleaning the LT5 engine. Do not direct water into the “V” area on the engine between the cylinder heads.
NOTICE: Don’t use a cleaner with a strong alkaline base. It will discolor the aluminum.
Aluminum Wheels Your aluminum wheels have a protective coating similar to the painted surface of your vehicle. Don’t use strong soaps, chemicals, chrome polish, abrasive cleaners or abrasive cleaning brushes on them because you could damage this coating. After rinsing thoroughly, a wax may be applied.
I NOTICE:
Don’t use an automatic vehicle wash that has hard silicon carbide cleaning brushes. These brushes can take the protective coating off your aluminum wheels.
Tires To clean your tires, use a stiff brush with a tire cleaner. When applying a tire dressing always take care to wipe off any overspray or splash from painted surfaces. Petroleum-based products may damage the paint finish.
6-63
the finish
Finish Damage Any stone chips, fractures or deep scratches in- should be repaired right away. Minor chips and scratches can be repaired with touch-up materials available from your dealer or other service outlets. Larger areas of finish damage can be corrected in your dealer’s body and paint shop. Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, accelerated corrosion (rust) can occur on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and other debris can collect. Dirt packed in closed areas of the frame should be loosened before being flushed. Your dealer or an underbody vehicle washing system can do this for you.
Fiberglass Springs
NOTICE: Don’t use corrosive or acidic cleaning agents, engine degreasers, aluminum cleaning agents or other harsh solvents to clean fiberglass springs; they’ll damage the springs.
Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ringlet-shaped discolorations, and small irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, Chevrolet will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 1 2 months or 12,000 miles (20 000 km) of purchase, whichever comes first.
6-64
Appearance Care and Maintenance Materials
You can get these from your GM Parts Department.
PART
NUMBER 12345343
I052277 1052863 1050172 16 1050173
10501 74 1050214
1050244 1050427 1050429
SIZE
16 oz. (0.473L)
12 02. (0.354L) 1 oz. (0.028kg) oz. (0.473L)
16 oz. (0.473L)
16 oz. (0.473L) 32 02. (0.946L) 16 02. (0.473L) 23 oz. (0.680L) 6 lbs. (2.72kg)
DESCRIPTION
GoodwrenchB Liquid Wax
USAGE
Exterior polish
Spray-A-Squeak Silicone Grease
Weatherstrips, Stops squeaks
Tar and Road Oil Remover
Chrome Cleaner and Polish
~~
Also removes old waxes, polishes
Removes rust and corrosion
Cleans white and black tires White Sidewall Tire Cleaner
VinyVLeather Cleaner
Spot and stain removal
Glass Cleaner
Spot and stain removal Fabric Cleaner Also spot cleans vinyls
Multi-Purpose Powdered Cleaner
Cleans vinyl and cloth, also, tires and mats
1052349 1051055 1051398" 1051515
12 oz. (0.340kg) 16 oz. (0.4731) 6 oz. (0.237L) 32 oz. (0.946L) 16 oz. (0.4731) * Not recommended for pigskin suede leather. See your General Motors Parts Departments for these products. See your Maintenance Schedule for other products.
1052870
Lubriplate (White Grease)
Spot Lifter
Washer Solvent
Wash-Wax (conc.)
For hood, trunk, door hinges and latches
Vinyl top dressing Preservatone
For cloth
Windshield-washing system
~~
Exterior wash
6-65
Vehicle Identification Number (VIN)
1.
Service Parts Identification Label You’ll find this label on the inside of your rear storage compartment. It’s very helpful if you ever need to order parts. On this label is:
ENGINE / li!95\
SAMPLEjUXSM072675
YEAR
PLANT
MODEL
CODE
ASSEMBLY
your VIN, the model designation, 0 paint information, and
a list of all production options and special equipment.
Be sure that this label is not removed from the vehicle.
This is the legal identifier for your Corvette. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration. Engine Identification The eighth character in your VIN is the engine code. This code will help you identify your engine, specifications, and replacement parts.
6-66
Add-on Electrical Equipment
Fuses & Circuit Breakers
NOTICE: Don’t add anything electrical to your Corvette unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Your vehicle has an air bag system. Before attempting to add anything electrical to your Corvette, see “Servicing Your Air Bag-Equipped Corvette” in the Index.
The wiring circuits in your vehicle are protected from short circuits by a combination of maxi-fuses, mini-fuses, and circuit breakers. This greatly reduces the chance of fires caused by electrical problems.
6-67
There are three fuse centers on your vehicle. One is in the right side of your instrument panel. Turn the knob and pull the door to access the fuses.
The other two fuse blocks are in the engine compartment. One is part of the Forward Lamp wiring harness (A), and the other is part of the ECM-Engine wiring harness (B). Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the correct size.
6-68
If you ever have a problem on the road and don’t have a spare fuse, you can borrow one of the correct value. Just pick some feature of your vehicle that you can get along without -- like the radio or cigarette lighter -- and use its fuse, if it is the size you need. Replace it as soon as you can. Headlamp Wiring The headlamp wiring is protected by a circuit breaker in the switch. An electrical overload will cause the lamps to go on and off, or in some cases to remain off. If this happens, have your headlamp wiring checked right away. Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem and not snow, etc., be sure to get it fixed. Power Windows and Other Power Options Circuit breakers protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away.
Instrument Panel Fuse Block
CIRCUIT BREAKERS
POWER SEAT
Two maxi -fuse blocks are located under hood near battery.
7 3c 7 8C 7
4c
9c 7 1oc 7
5c
STOP/HAZ
CRANK AIR BAG
CRANK CLUTCH
P/N
IC 7 MIR 6c 7
AK: MDL WIPER
IGN HTD RDO
TAIL
2 1
HORN
7c 7 7 =c 7
18C
19c
F.P. 2
CCM3
VALET A/C
ENG2
lNJl
CLUTCH UTILITY OXYGEN SEN
1 3 1 7 1 4 1 7
1 1 1 RH ILLUM LH ILLUM CNSLILLUM F.P. 1
15c 7 7 2oc 7 1 6 1 7 17c 21c 722C 7 4 7 2 4 c 7 2 5 1 7 26C 7 27c 3 1 1 7 3zc 7 =c 7 3 4 c 7 3 5 1 7 7401 7 7 ~ C 7
7 2ac 7
7 431
CCMP RDOBAlT
PWR MIRROR CRUISE E.C.M. AIR BAG
CLUSTER P.K.E.
BACKUP
RHCTSY
LHCTSY
CCM 1
ENG 1
TURN
L.C.D.
COIL
INJ 2
3 6 1
3 9 1
3 0 1
3 7 1
FAN
3 8 C
29c
4 1 1 7 4 2 c
SPORTSEAT PWR LOCK A/C
PROG CIGAR HATCH
POWER WINDOW
6-69
1. Heater, A/C Programmer 2. Bl@k 3. Windshield Wipermasher Switch Assembly 4, Radio Receiver (Ignition) 5. Heated Mirrors, Heater and A/C Control Head,
Heater and N C Programmer
6. Light Switch, Daytime Running Lamps Module 7. Horn Relay 8. Hazard Flashers; Brake Switch 9. Crank-Air Bag 10. Crank-ParWNeutral Switch (Automatic); Clutch
Switch (Manual) 1 1. RH Illumination 12. LH Illumination 13. Console Illumination 14. Fuel Pump 1 15. Fuel Pump 2 (LT5) 16. Central Control Module; Daytime R
Module
unning Lamps
17. Generator; Automatic Transmission Vacuum Pump
(LT5); Valet Mode (LT5); EGR Circuit (LT5); Oxygen Sensors (LT5)
18. A/C Compressor Clutch; Heater and A/C Control Head; Heater and N C Programmer; Rear Defog Relay
19. Accessory Plug 20. Heated Oxygen Sensors (LT1) 21. Fuel Pump Relay #2 (LT5); Selective Ride Control Module; ABS Module; Brake Switch (Automatic); Air Pump Relay; Air Bypass Valve (LT5)
22. Injectors #1,4,6,7 (LTl); Primary Injectors #1-8
(LT5); Ignition Coil (LT5)
23. Injectors #2,3,5, 8 (LTl); Secondary SF1 Control
Modules (LT5)
24. Turn Signal Flashers 25. Ignition Coil and Ignition Coil Module (LT1) 26. Passive Keyless Entry Module 27. Instrument Cluster; Driver Information Center;
Air Bag Denn; Acceleration Slip Regulation Switch (LT5)
28. Back-up Lamps Switch; Transmission Position
Switch; One to Four Shift Solenoid 29. Cooling Fan Relay Coil #I, #2, #3 30. Camshaft Sensor (LT5); Canister Purge Solenoid;
Throttle Position Sensor Buffer Module (LT5); EGR Circuit (LT1); Secondary Air Inlet Solenoid (LT5); Ignition Control Module (LT5); HVAC Solenoid Assembly; Mass Airflow Sensor (LT 1); One to Four Shift Relay
3 1. Power Mirror Adjuster Control; Lighted Rearview
Mirror; Visor Vanity Mirrors
32. Cruise Control Engage Switch; Daytime Running
Lamps Module; Low Tire Pressure Warning Module; Cruise Control Cut-Off Relay
33. Engine Control Module 34. Air Bag System 35. Central Control Module 36. Footwell Courtesy Lamps; Door Courtesy Lamps;
Glove Compartment Lamps; Lighted Rearview Mirror
37, Bose@ Amplifier Relay; Power Antenna Relay;
Cargo Compartment Lamps
38. Instrument Cluster; Tone Generator; Dome Lamp
Relay
39. Central Control Module 40, Radio Receiver (Battery); Radio Control Head;
Passive Keyless Entry Module
41. Sport Seats 42. Power Door Lock Switches; Driver Information
Center; Passive Keyless Entry Module
43. Heater and A/C Programmer 44. Cigarette Lighter; Accessory Plug 45. Hatch or Deck Lid Release Relay K. Power Seats L. Blank M. Power Windows N. Blank P. Blank
6-71
1. Interior Lighting 2. Primary Cooling Fan 3. LH Headlamp Motor 4. RH Headlamp Motor 5. Secondary Cooling Fan 6. Exterior Lighting 7. Power Accessory (Power Locks, Hatch, Lighter,
Seats)
8. Air Pump
Forward Lamp Fuse Block
INTERIOR LIGHTING
PRIMARY COOLING FAN
LH HDLP MOTOR
RH HDLP MOTOR
EXTERIOR LIGHTING
POWER ACCSY
AIR PUMP
6-72
ECM Engine Fuse Block
FUEL PUMP
ABWASR ECU
A/C BLOWER
RR DEFOG
IGNITION
IGNITION
BRAKE HYDRAULICS
Engine Control Module Fuel Pump Anti-Lock Brakes; Acceleration Slip Regulation System A/C Blower Rear Defogger Ignition Ignition Brake Hydraulics
1. 2. 3. 4. 5. 6. 7. 8. Underhood Lamps Fuse
Your Corvette has one single fuse underhood for the underhood lamps. The fuse is under the hood on the driver’s sidemarker lamp assembly.
6-73
......................
Driver Information Center Floor Courtesy ............................. 562 Fog ...................................... 896 Front Parkingmurn Signal ................. 2057NA Headlamp ............................. HP6054 ............................ Instrument Cluster License ................................... 24 MirrorFlood ............................... 74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Mirror Reading Radio Rear Courtesy (Convertible) .................. 562 ............ 906 Rear Courtesy (except Convertible) Sidemarker ................................ 24 Tail/Stop/Turn ............................ 2057 Underhood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Visor Vanity Mirror .......................... 74
......................................
Leaving your hood open and your underhood lamps on can drain your battery . If you need to keep the hood open for an extended period of time. remove the underhood lamps fuse . Replacement Bulbs
Air Conditioningmeater Control . . . . . . . . . . . . . . . . 37 . . . . . . . . . . . 194NA Automatic Transmission Indicator Back-up ................................. 1156 Center High-Mounted Stoplamp (except ZR- 1) ... 1156 Center High-Mounted Stoplamp (ZR- 1) . . . . . . . . 89 1 Console .................................. 564 Cornering ................................. 1156 Door Courtesy ........................... . 2 1 2-2 DoorFlood ................................ 73 * These bulbs are not owner.serviceab1e . See your dealer.
6-74
Capacities and Specifications Engine Type ...................................................................................... FueI Delivery ................................................ Valve Arrangement
V8 Sequential Multiport Fuel Injection (SFI)
VIN Engine Code J .......................................................... Dual Overhead Cam VIN Engine Code P ............................................................. Overhead Valve 350 CID (5.7L)
Piston Displacement ............................................................... Bore
VIN Engine Code J .............................................................. VIN Engine Code P ..........................................................
Stroke
Compression Ratio
VINEngineCodeJ .............................................................. VIN Engine Code P ............................................................
VINEngineCodeJ ..................................................................... VINEngineCodeP .....................................................................
11.O:l 10.5:l Firing Order ................................................................... 1-8-4-3-6-5-7-2 Thermostat Temperature Specification ................................................
180°F (82 “C)
3.90” (99 mm) 4.00” (101.6 mm)
3.66”(93mm) 3.48” (88.39 mm)
6-75
Replacement Parts Air Cleaner Filter ......................................
...............................
A1097C GM Part No. 25096933 or equivalent
.....................................................................
Battery VIN Engine Code J .................................... VIN Engine Code P 75B-72 Coolant High Fill Reservoir Cap ............................ RC36/GM Part No. 6410785 or equivalent Crankcase Ventilation Valve VIN Engine Code J ........................................................ CV746CB and CV9 13C GM Part No. 25042723 and GM Part No. 25098197or equivalent CV895C GM Part No. 25095452 or equivalent
....................................................................
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5 2 - 7 2
VIN Engine Code P
Engine Oil Filter
VIN Engine Code J
..............................................................
(black) GM Part No. 25014155 or equivalent
PF97OC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VIN Engine Code P ........ PCV Valve (LT1) .............................. PCV
(LT5) ...........................
Valve
GM Part No. 25010908 or equivalent
......................... AC Type CV895C
................. CV746CB
Type
AC
~ .
AC Type CV913C
6-76
Replacement Parts Flat Ratchet Wrench (Convertible Hardtop Only) . . . . . . . . . . . . . . . . . . . GM Part No. 10137741 or equivalent Serpentine Belt VIN Engine Code J ........................................................ VIN Engine Code P ........................................................ Spark Plug VIN Engine Code J ..........................................................
4 1-907 (0.050" Gap) GM Part No. 5614247 and GM Part No. 5614355 or equivalent 41 -906 (0.050" Gap) GM Part No. 5614244 or equivalent Tom@ Wrench ................................................. GM Part No. 1017231 1 or equivalent Wheel Nuts Wheel Nut Torque ...........................................................
VIN Engine Code P ..........................................................
GM Part No. 10067477 GM Part No. 10230259
100 1b. ft. (140 Nam)
6-77
See the refrigerant information lab
el und er the hood.
10.0 pt. (4.7 L)* . . . . . . . . . . . . . 21.6pt. (10.2L)*
Capacities (Approximate) The following approximate capacities are given in U.S. and metric conversions. Air Conditioning? ............................ Automatic Transmission Drain and Refill ....................... Overhaul . . . . . . . Cooling System VIN Engine Code J .................... VIN Engine Code P .................... Crankcase VIN Engine Code J Without Filter Change . . . . . . . . . . . . . . . . . . . 7.6 qt. (7.2 L)* With Filter Change ..................... 8.6 qt. (8.1 L)* VIN Engine Code P Without Filter Change . . . . . . . . . . . . . . . . . . . 4.0 qt. (3.8 L)* With Filter Change ..................... 4.5 qt. (4.3 L)* Fuel Tank ........................... 20.0 gal. (75.7 L) Manual Transmission (Overhaul) . . . . . . . . . . 4.4 pt. (2.1 L)* Rear Axle Lubricant ............................. 1.5 qt. (1.42 L) Limited Slip Additive . . . . . . . . . . . . . . . . . . . 4.0 oz. (1 18 ml)
14.7 qt. (13.9 L) 17.8 qt. (16.9 L)
7 Not all air conditioning refrigerants are the same. If the air conditioning system in your vehicle needs refrigerant, be sure the proper refrigerant is used. If you’re not sure, ask your Chevrolet dealer.
6-78
* Recheck fluid level after filling. See Section 6 or
the Index.
Vehicle Dimensions Wheelbase ...................... Tread
96.2" (2 444 mm)
57.7" (1 466 mm)
Front ........................ Rear Coupe and Convertible . . . . . . . . . . 59.1 ' I (1 500 mm) ZR-1 ........................ 60.6" (1 539 mm) Length ........................ 178.5" (4 535 mm) Width Coupe ........................ 70.7'' (1 796 mm) Convertible and ZR- 1 . . . . . . . . . . . . 73.1 ' I (1 856 mm) Height
Coupe and ZR- 1 . . . . . . . . . . . . . . . 46.3" (1 177 mm) Convertible . . . . . . . . . . . . . . . . . . . 47.3" (1 202 mm)
Power Curves -- LT1 Engine
Power Curves
LT1 Engine
300
g 200
100
4 ::: 245 2 210 w 175 5 u)
280
140 w h!
105 2
70
( D l -
1 3 5
ENGINE SPEED-RPM
6-79
Belt Routing -- LTl (Code P) Engine
Power Curves -- LT5 Engine
Power Curves LT5 Engine
450 r
450 400 350 5 300 g - 250 $ 200 g - 50 100 m
150 Y
ENGINE SPEED-RPM
Belt Routing -- LT5 (Code J) Engine
6-80
e
Section 7 Maintenance Schedule
RECOMMENDED
LEVEL AND CHANGE AS
IMPORTANT: KEEP ENGINE OIL AT THE PROPER
protection m-
This section covers the maintenance required for your Corvette. Your vehicle needs these services to retain its safety, dependability and emission control performance.
Plan
Introduction Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance procedures are important. Improper vehicle maintenance or the removal of important components can significantly affect the quality of the air we breathe. Improper fluid levels or even the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to help keep your vehicle in good condition, please maintain your vehicle properly.
Have you purchased the GM Protection Plan ? The Plan supplements your new vehicle warranties. See your Chevrolet dealer for details.
7-1
I 1 How This Section is Organized
The remainder of this section is divided into five parts: “Part A: Scheduled Maintenance Services” shows what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your dealer’s service department or another qualified service center do these jobs.
If you are skilled enough to do some work on your vehicle, you will probably want to get the service information GM publishes. See “Service Publications” in the Index.
7-2
“Part B: Owner Checks and Services” tells you what should be checked whenever you stop for fuel. It also explains what you can easily do to help keep your vehicle in good condition. “Part C: Periodic Maintenance Inspections” explains important inspections that your Chevrolet dealer’s service department or another qualified service center should perform. “Part D: Recommended Fluids and Lubricants” lists some products GM recommends to help keep your vehicle properly maintained. These products, or their equivalents, should be used whether you do the work yourself or have it done. “Part E: Maintenance Record’’ provides a place for you to record the maintenance performed on your vehicle. Whenever any maintenance is performed, be sure to write it down in this part. This will help you determine when your next maintenance should be done. In addition, it is a good idea to keep your maintenance receipts. They may be needed to qualify your vehicle for warranty repairs.
Part A: Scheduled Maintenance Services Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we don’t know exactly how you’ll drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in many other ways. Because of all the different ways people use their GM vehicles, maintenance needs vary. You may even need more frequent checks and replacements than you’ll find in the schedules in this section. So please read this section and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your Chevrolet dealer. This part tells you the maintenance services you should have done and when you should schedule them. If you go to your dealer for your service needs, you’ll know that GM-trained and supported service people will perform the work using genuine GM parts.
The proper fluids and lubricants to use are listed in Part D. Make sure whoever services your vehicle uses these. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. These schedules are for vehicles that:
carry passengers and cargo within recommended limits. You will find these limits on your vehicle’s Tire-Loading Information label. See “Loading Your Vehicle” in the Index. are driven on reasonable road surfaces within legal driving limits. use the recommended unleaded fuel. See “Fuel” in the Index.
Selecting the Right Schedule First you’ll need to decide which of the two schedules is right for your vehicle. Here’s how to decide which schedule to follow:
7-3
Maintenance Schedule I Schedule I Definition Follow Maintenance Schedule I if any one of these is true for your vehicle: 0 Most trips are less than 5 to 10 miles (8 to 16 km).
This is particularly important when outside temperatures are below freezing.
0 Most trips include extensive idling (such as frequent
driving in stop-and-go traffic).
0 Most trips are through dusty areas. Schedule I should also be followed if the vehicle is used for delivery service, police, taxi, or other commercial application.
Schedule I Intervals Every 3,000 Miles (5 000 km) or 3 Months, Whichever Occurs First
Engine Oil and Filter Change
Every 6,000 Miles (10 000 km) or 6 Months, Whichever Occurs First
Chassis Lubrication
Every 15,000 Miles (25 000 km)
Air Cleaner Filter Inspection, if driving in dusty
conditions
Automatic Transmission Service (severe conditions only)
Every 30,000 Miles (50 000 km) Air Cleaner Filter Replacement Spark Plug Wire Inspection Fuel Tank, Cap and Lines Inspection Engine Accessory Drive Belt Inspection (or every
24 months, whichever occurs first)
Cooling System Service (or every 24 months,
whichever occurs first)
7-4
Every 100,000 Miles (166 000 km)
Spark Plug Replacement Automatic Transmission Service (normal conditions)
Maintenance Schedule
Follow Schedule I1 only if none of the conditions from Schedule I is true.
I Schedule I1 Intervals
Every 7,500 Miles (12 500 km)
Engine Oil and Filter Change (or every 12 months,
whichever occurs first)
Chassis Lubrication (or every 12 months, whichever
occurs first)
Every 15,000 Miles (25 000 km)
Automatic Transmission Service (severe conditions
only 1
Every 30,000 Miles (50 000 km)
Engine Accessory Drive Belt Inspection (or every
24 months, whichever occurs first)
Cooling System Service (or every 24 months,
whichever occurs first)
Spark Plug Wire Inspection Air Cleaner Filter Replacement Fuel Tank, Cap and Lines Inspection
Every 100,000 Miles (166 000 km)
Spark Plug Replacement Automatic Transmission Service (normal conditions)
7-5
Maintenance Schedule I
The services shown in this schedule up to 100,000 miles (166 000 km) should be performed after 100,000 miles (166 000 km) at the same intervals. Footnotes 3- The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of vehicle useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.
* Your vehicle has an Engine Oil Life Monitor. This monitor will show you when to change the oil -- usually between 3,000 miles (5 000 km) and 7,500 miles (12 500 km) since your last oil change. Under severe conditions the indicator may come on before 3,000 miles (5 000 km). Never drive your vehicle more than 7,500 miles (12 500 km) or 12 months without an oil change. The system won’t detect dust in the oil. So if you drive in a dusty area be sure to change your oil every 3,000 miles (5 000 km) or sooner if the CHANGE OIL light comes on. Remember to reset the Oil Life Monitor when the oil has been changed. For more information, see “Engine Oil Life Monitor” in the Index.
7-6
1 Maintenance Schedule I 3,000 Miles (5 000 km) 17 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
DATE
ACTUAL MILEAGE
SERVICED BY:
6,000 Miles (10 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
0 Lubricate the suspension, $teering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
I DATE
ACTUAL
MILEAGE
SERVICED
BY:
7-7
I Maintenance Schedule I 9,000 Miles (15 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
12,000 Miles (20 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. * Lubricate the suspension, steering and transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
7 SERVICED BY:
DATE ACTUAL MILEAGE SERVICED
BY:
DATE
ACTUAL
MILEAGE
7-8
I Maintenance Schedule I 15,000 Miles (25 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. * Inspect air cleaner filter if you are driving in dusty conditions. Replace filter if necessary. An Emission Control Service.
17 Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside
temperature regularly reaches 90 OF (32°C) or higher.
If you do not use your vehicle under any of these conditions, change the fluid and filter at 100,000 miles (1 66 000 km). Manual transmission fluid doesn’t require change.
- In hilly or mountainous terrain. - Uses such as found in taxi, police or
delivery service.
DATE
ACTUAL MILEAGE
SERVICED BY:
7-9
I Maintenance Schedule I 18,000 Miles (30 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service.
0 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
21,000 Miles (35 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. *
DATE SERVICED
ACTUAL MILEAGE
BY:
DATE
ACTUAL MILEAGE
SERVICED BY:
7-10
I Maintenance Schedule I 24,000 Miles (40 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service, *
0 Lubricate the suspension, steering and
transmission shift linkage, parkmg brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
27,000 Miles (45 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
DATE
ACTUAL MILEAGE
SERVICED BY:
7-11
Maintenance Schedule I 30,000 Miles (50 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
17 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact Points and linkage (or every 6 months, whichever occurs first). 0 Inspect engine accessory drive belt (or
every 24 months, whichever occurs first). An Emission Control Service 0 Drain, flush and refill cooling system (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Service.
7-12
[7 Inspect spark plug wires. An Emission Control
Service. -f-
[7 Replace air cleaner filter. Replace filter
more often under dusty conditions. An Emission Control Service. Inspect fuel tank, cap and lines for damage or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. An Emission Control
Service. -f-
0 Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside temperature regularly reaches 90 O F (32 O C) or higher.
- In hilly or mountainous terrain.
Maintenance Schedule I
- Uses such as found in tax
i, pol ice or
delivery service.
If you do not use your vehicle under any of these conditions, change the fluid and filter at 100,000 miles (1 66 000 km). Manual transmission fluid doesn’t require change.
I DATE
I ACTUAL MILEAGE
ISERVICED By:l
33,000 Miles (55 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
ACTUAL MILEAGE
SERVICED BY:
7-13
I Maintenance Schedule I 36,000 Miles (60 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Sewice. *
0 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
39,000 Miles (65 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. *
DATE ACTUAL MILEAGE SERVICED
BY:
DATE ACTUAL MILEAGE SERVICED
BY:
7-14
I Maintenance Schedule I 42,000 Miles (70 000 km)
Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. *
0 Lubricate the suspension, steering and
transmission shift linkage, parlung brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
45,000 Miles (75 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
0 Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside
temperature regularly reaches 90 O F (32°C) or higher.
DATE
ACTUAL MILEAGE
SERVICED BY:
- In hilly or mountainous terrain. - Uses such as found in taxi, police or
delivery service.
(Continued)
7-15
Maintenance Schedule I
45,000 Miles (75 000 km) (Continued)
I f you do not use your vehicle under any of these conditions, change the fluid and filter at 100,000 miles ( I 66 000 km). Manual transmission fluid doesn't require change. 0 Inspect air cleaner filter if you are driving
in dusty conditions. Replace filter if necessary. An Emission Control Service.
48,000 Miles (80 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. * 0 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
I DATE
I ACTUAL MILEAGE
SERVICED BY: I
DATE ACTUAL MILEAGE SERVICED
BY:
7-16
I
Maintenance Schedule I 51,000 Miles (85 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
54,000 Miles (90 000 km)
Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. *
0 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
DATE
ACTUAL MILEAGE
SERVICED BY:
7-17
I
I Maintenance Schedule I ~ 57,000 Miles (95 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. *
DATE ACTUAL MILEAGE SERVICED
BY:
7-18
60,000 Miles (100 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service.
0 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, wluchever occurs first).
0 Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside
temperature regularly reaches 90 O F (32 O C) or higher.
- In hilly or mountainous terrain.
Maintenance Schedule I
- Uses such as found in taxi, police or
delivery service.
Ifyou do not use your vehicle under any of these conditions, change the fluid and filter at 100,000 miles (1 66 000 km). Manual transmission fluid doesn’t require change.
I7 Inspect engine accessory drive belt (or
every 24 months, whichever occurs first). An Emission Control Service. 0 Drain, flush and refill cooling system (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Service.
0 Inspect spark plug wires. An Emission Control 0 Replace air cleaner filter. Replace filter
Sewice.
more often under dusty conditions. An Emission Control Service.
0 Inspect fuel tank, cap and lines for damage
or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. An Emission Control Service.?
DATE
ACTUAL MILEAGE
SERVICED BY:
7-19
I
I Maintenance Schedule I 63,000 Miles (105 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. *
66,000 Miles (110 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. * 0 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
DATE ACTUAL MILEAGE SERVICED
BY:
DATE ACTUAL MILEAGE SERVICED
BY:
7-20
1 Maintenance Schedule I 69,000 Miles (115 000 km)
Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Sewice. *
72,000 Miles (120 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Sewice. *
0 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
DATE
ACTUAL MILEAGE
SERVICED BY:
DATE
ACTUAL MILEAGE
SERVICED B Y
7-21
1 Maintenance Schedule I 75,000 Miles (125 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
0 Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside
temperature regularly reaches 90 OF (32°C) or higher.
- In hilly or mountainous terrain. - Uses such as found in taxi, police or
delivery service.
7-22
If you do not use your vehicle under any of , these conditions, change the fluid and filter at 100,000 miles (166 000 km). Manual transmission fluid doesn’t require change. 0 Inspect air cleaner filter if you are driving
in dusty conditions. Replace filter if necessary. An Emission Control Service.
DATE
ACTUAL MILEAGE
SERVICED BY:
1 Maintenance Schedule I 78,000 Miles (130 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
17 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
81,000 Miles (135 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
DATE
ACTUAL MILEAGE
7-23
I Maintenance Schedule I 84,000 Miles (140 000 km)
Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service.
0 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
DATE ACTUAL MILEAGE SERVICED
BY:
7-24
87,000 Miles (145 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. *
: ACTUAL MILEAGE SERVICED BY:
I Maintenance Schedule I 90,000 Miles (150 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
0 Lubricate the suspension, steering and
transmission shift linkage, parlung brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
0 Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside
temperature regularly reaches 90 O F (32 O C) or higher.
- In hilly or mountainous terrain. - Uses such as found in taxi, police or
delivery service.
If you do not use your vehicle under any of these conditions, change the fluid and filter at 100,000 miles (1 66 000 km). Manual transmission fluid doesn’t require change.
0 Inspect engine accessory drive belt (or
every 24 months, whichever occurs first). An Emission Control Service.
(Continued)
7-25
Maintenance Schedule I
90,000 Miles (150 000 km) (Continued) 0 Drain, flush and refill cooling system (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Service.
0 Inspect spark plug wires. An Emission 0 Replace air cleaner filter. Replace filter
Control Service.
more often under dusty conditions. An Emission Control Service.
0 Inspect fuel tank, cap and lines for damage
or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. An Emission Control Service.
7-26
I
[ Maintenance Schedule I 93,000 Miles (155 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
96,000 Miles (160 000 km)
Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. * 0 Lubricate the suspension, steering and
transmission shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).
DATE
ACTUAL MILEAGE
SERVICED BY:
7-27
r Maintenance Schedule I
~ 99,000 Miles (165 000 km) 0 Change engine oil and filter (or every
3 months, whichever occurs first). An Emission Control Service. *
100,000 Miles (1 66 000 km) 0 Replace spark plugs. An Emission Control 0 If you haven’t used your vehicle under
Service.
severe service conditions listed previously and, therefore, haven’t changed your automatic transmission fluid, change both the fluid and filter.
DATE ACTUAL MILEAGE SERVICED
BY:
DATE ACTUAL MILEAGE SERVICED
B Y
7-28
The services shown in this schedule up to 100,000 miles (166 000 km) should be performed after 100,000 miles (1 66 000 km) at the same intervals. Footnotes The U.S. Environmental Protection Agency or the
California Air Resources Board has determined that the