Download PDF Manual

(2 Pin)


F36


F38


Micro Fuse (3 Pin)


F13


F18
F23


F28


F33


Usage


Discrete Logic Ignition Sensor Not Used


Usage


OnStar/Heating, Ventilation, and Air Conditioning Airbag Data Link Connector/USDB Instrument Panel/ Sensing and Diagnostic Module Ignition Not Used


Micro J-Case Fuse F02
F03
F06
F07
F39


F41


F42
F43
F45
F46


J-Case Fuse F30
F40
F44


Usage


Not Used Not Used Not Used Not Used Auxiliary Power Outlet 2
Auxiliary Power Outlet 1/Lighter Left Power Window Driver Power Seat Right Power Window Passenger Power Seat


Usage


Not Used Auxiliary Power Outlet Auxiliary Power Outlet


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


Mini Fuse (2 Pins)


Usage


F37


Not Used


Micro Relay


K1


K2


Usage


Retained Accessory Power/Accessory Run/Crank


Wheels and Tires


Tires Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer.


{ Warning


. Poorly maintained and


improperly used tires are dangerous.


. Overloading the tires can


cause overheating as a result of too much flexing. There could be a blowout and a serious crash. See Vehicle Load Limits 0 205


ii


(Continued)


Vehicle Care


295


Warning (Continued)


. Underinflated tires pose


the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when the tires are cold.


. Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when hitting a pothole. Keep tires at the recommended pressure.


. Worn or old tires can cause a crash. If the tread is badly worn, replace them.


(Continued)


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


296


Vehicle Care


Warning (Continued)


. Replace any tires that


have been damaged by impacts with potholes, curbs, etc. Improperly repaired tires can cause a crash. Only the dealer or an authorized tire service center should repair, replace, dismount, and mount the tires.


. Do not spin the tires in


excess of 56 km/h (35 mph) on slippery surfaces such as snow, mud, ice, etc. Excessive spinning may cause the tires to explode.


All-Season Tires This vehicle may come with all-season tires. These tires are designed to provide good overall performance on most road surfaces


and weather conditions. Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. Original equipment all-season tires can be identified by the last two characters of this TPC code, which will be “MS.” Consider installing winter tires on the vehicle if frequent driving on snow or ice-covered roads is expected. All-season tires provide adequate performance for most winter driving conditions, but they may not offer the same level of traction or performance as winter tires on snow or ice-covered roads. See Winter Tires 0 296


ii


Winter Tires This vehicle was not originally equipped with winter tires. Winter tires are designed for increased traction on snow and ice-covered roads. Consider installing winter tires on the vehicle if frequent driving on ice or snow covered roads is expected. See your dealer


ii


for details regarding winter tire availability and proper tire selection. Also, see Buying New Tires 0 310
With winter tires, there may be decreased dry road traction, increased road noise, and shorter tread life. After changing to winter tires, be alert for changes in vehicle handling and braking. If using winter tires: . Use tires of the same brand and


tread type on all four wheel positions.


. Use only radial ply tires of the


same size, load range, and speed rating as the original equipment tires.


Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y, and ZR speed rated tires. If winter tires with a lower speed rating are chosen, never exceed the tire's maximum speed capability.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


All-Terrain Tires This vehicle may have all-terrain tires. These tires provide good performance on most road surfaces, weather conditions, and for off-road driving. See Off-Road Driving 0 197
The tread pattern on these tires may wear more quickly than other tires. Consider rotating the tires more frequently than at 12 000 km (7,500 mi) intervals if irregular wear is noted when the tires are inspected. See Tire Inspection 0 307


ii


ii


Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples show a typical passenger vehicle tire and a compact spare tire sidewall.


Vehicle Care


297


GM's TPC specifications meet or exceed all federal safety guidelines. (3) DOT (Department of Transportation) : The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. DOT Tire Date of Manufacture : The last four digits of the TIN indicate the tire manufactured date. The first two digits represent the week (01– 52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. (4) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the


Passenger (P-Metric) Tire Example (1) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section. (2) TPC Spec (Tire Performance Criteria Specification) : Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


298


Vehicle Care


manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (5) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (6) Uniform Tire Quality Grading (UTQG) : Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading 0 312
(7) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load. (8) Temporary Use Only : Only use a temporary spare tire until the road tire is repaired and


ii


replaced. This spare tire should not be driven on over 112 km/h (70 mph), or 88 km/h (55 mph) when pulling a trailer, with the proper inflation pressure. See Full-Size Spare Tire 0 326


ii


Compact Spare Tire Example (1) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (2) Temporary Use Only : The compact spare tire or temporary use tire should not be driven at speeds over 80 km/h (50 mph). The compact spare tire is for


ii


ii


and If a Tire Goes


emergency use when a regular road tire has lost air and gone flat. If the vehicle has a compact spare tire, see Compact Spare Tire 0 325
Flat 0 315
(3) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (4) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


ii


(5) Tire Inflation : The temporary use tire or compact spare tire should be inflated to 420 kPa (60 psi). For more information on tire pressure and inflation see Tire Pressure 0 302
(6) Tire Size : A combination of letters and numbers define a tire's width, height, aspect ratio, construction type, and service description. The letter T as the first character in the tire size means the tire is for temporary use only. (7) TPC Spec (Tire Performance Criteria Specification) : Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.


Tire Designations


Tire Size The following is an example of a typical passenger vehicle tire size.


(1) Passenger (P-Metric) Tire : The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (2) Tire Width : The three-digit number indicates the tire section width in millimeters from sidewall to sidewall.


Vehicle Care


299


(3) Aspect Ratio : A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item 3 of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide. (4) Construction Code : A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction. (5) Rim Diameter : Diameter of the wheel in inches. (6) Service Description : These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


300


Vehicle Care


Tire Terminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight : The combined weight of optional accessories. Some examples of optional accessories are automatic transmission, power windows, power seats, and air conditioning. Aspect Ratio : The relationship of a tire's height to its width. Belt : A rubber coated layer of cords between the plies and the tread. Cords may be made from steel or other reinforcing materials.


Bead : The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire : A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure : The amount of air pressure in a tire, measured in kPa (kilopascal) or psi (pounds per square inch) before a tire has built up heat from driving. See Tire Pressure 0 302
Curb Weight : The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings : A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S.


ii


ii


Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR : Gross Vehicle Weight Rating. See Vehicle Load Limits 0 205
GAWR FRT : Gross Axle Weight Rating for the front axle. See Vehicle Load Limits 0 205
GAWR RR : Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits 0 205
Intended Outboard Sidewall : The side of an asymmetrical tire that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure.


ii


ii


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


Vehicle Care


301


Light Truck (LT-Metric) Tire : A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index : An assigned number ranging from 1 to 279
that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure : The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating : The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight : The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight.


ii


Normal Occupant Weight : The number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lb). See Vehicle Load Limits 0 205
Occupant Distribution : Designated seating positions. Outward Facing Sidewall : The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire : A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure : Vehicle manufacturer's recommended


ii


ii


tire inflation pressure as shown on the tire placard. See Tire and Vehicle Pressure 0 302
Load Limits 0 205
Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated. Sidewall : The portion of a tire between the tread and the bead. Speed Rating : An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction : The friction between the tire and the road surface. The amount of grip provided. Tread : The portion of a tire that comes into contact with the road.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


302


Vehicle Care


ii


Treadwear Indicators : Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1.6 mm (1/16 in) of tread remains. See When It Is Time for New Tires 0 309
UTQGS (Uniform Tire Quality Grading Standards) : A tire information system that provides consumers with ratings for a tire's traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading 0 312
Vehicle Capacity Weight : The number of designated seating positions multiplied by 68 kg (150 lb) plus the rated cargo load. See Vehicle Load Limits 0 205


ii


ii


Vehicle Maximum Load on the Tire : Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard : A label permanently attached to a vehicle showing the vehicle capacity weight and the original equipment tire size and recommended inflation pressure. See “Tire and Loading Information Label” under Vehicle Load Limits 0 205


ii


Tire Pressure Tires need the correct amount of air pressure to operate effectively.


Caution


Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:


. Tire overloading and


overheating which could lead to a blowout.


. Premature or irregular wear. . Poor handling. . Reduced fuel economy. Overinflated tires, or tires that have too much air, can result in:


. Unusual wear. . Poor handling. . Rough ride. . Needless damage from


road hazards.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures. The recommended pressure is the minimum air pressure needed to support the vehicle's maximum load carrying capacity. See Vehicle Load Limits 0 205
How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.


ii


When to Check Check the tires once a month or more. Do not forget to check the spare tire. If the vehicle has a compact spare tire, it should be at 420 kPa (60 psi). See Compact Spare Tire 0 325
Full-Size Spare Tire 0 326
additional information.


and for


ii


ii


How to Check Use a good quality pocket-type gauge to check tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air. Re-check the tire pressure with the tire gauge.


Vehicle Care


303


Return the valve caps on the valve stems to prevent leaks and keep out dirt and moisture.


Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


304


Vehicle Care


(TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is


combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation 0 304
See Radio Frequency Statement 0 371


ii


ii


Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmit the tire pressure readings to a receiver located in the vehicle.


When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


ii


shown on the Tire and Loading Information label. See Vehicle Load Limits 0 205
A message to check the pressure in a specific tire displays in the Driver Information Center (DIC). The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed. For additional information and details about the DIC operation and displays, see Driver Information Center (DIC) (Base Level) 0 123
Driver Information Center (DIC) (Uplevel) 0 126
0 135
The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and needs to be inflated to the proper pressure.


and Tire Messages


or


ii


ii


ii


ii


A Tire and Loading Information label shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load , for an example of the Limits 0 205
Tire and Loading Information label and its location. Also see Tire Pressure 0 302
The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection 0 307
Tires 0 295


, Tire Rotation 0 308


, and


ii


ii


ii


ii


Caution


Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use only the GM approved tire sealant available through your dealer or included in the vehicle.


Vehicle Care


305


TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire pressure warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message also displays. The malfunction light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause these to come on are: . One of the road tires has been


replaced with the spare tire. The spare tire does not have a TPMS sensor. The malfunction light and the DIC message should go off after the road tire is replaced and the sensor matching process is performed successfully. See “TPMS Sensor Matching Process” later in this section.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


306


Vehicle Care


. The TPMS sensor matching process was not done or not completed successfully after rotating the tires. The malfunction light and the DIC message should go off after successfully completing the sensor matching process. See “TPMS Sensor Matching Process” later in this section.


. One or more TPMS sensors are


missing or damaged. The malfunction light and the DIC message should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer for service.


. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended could prevent the TPMS from functioning properly. See Buying New Tires 0 310


ii


. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.


If the TPMS is not functioning properly, it cannot detect or signal a low tire condition. See your dealer for service if the TPMS malfunction light and DIC message come on and stay on. TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the vehicle’s tires or replacing one or more of the TPMS sensors. Also, the TPMS sensor matching process should be performed after replacing a spare tire with a road tire containing the TPMS sensor. The malfunction light and the DIC message should go off at the next ignition cycle. The sensors are matched to the tire/wheel positions, using a TPMS relearn tool, in the following order: driver side front tire,


passenger side front tire, passenger side rear tire, and driver side rear. See your dealer for service or to purchase a relearn tool. A TPMS relearn tool can also be purchased. See Tire Pressure Monitor Sensor Activation Tool at www.gmtoolsandequipment.com or call 1-800-GM TOOLS (1-800-468-6657). There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. The TPMS sensor matching process is: 1. Set the parking brake. 2. Turn the ignition to ON/RUN


3.


with the engine off. If the vehicle has an uplevel DIC, make sure the Tire Pressure info page option is turned on. The info pages on the DIC can be turned on and off through the Settings menu.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


4.


5.


ii


ii


or


See Driver Information Center (DIC) (Base Level) 0 123
Driver Information Center (DIC) (Uplevel) 0 126
If the vehicle has an uplevel DIC, use the DIC controls on the right side of the steering wheel to scroll to the Tire Pressure screen under the DIC info page. If the vehicle has a base level DIC, use the MENU button to select the Vehicle Information menu in the DIC. Use the thumbwheel to scroll to the Tire Pressure Menu item screen. If the vehicle has an uplevel DIC, press and hold the V (Set/Reset) button located in the center of the DIC controls. If the vehicle has a base level DIC, press the SET/CLR button to begin the sensor matching process.


A message asking if the process should begin should appear. Press the SET/CLR button again to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen.


6. Start with the driver side


front tire.


7. Place the relearn tool against


the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.


8. Proceed to the passenger side


front tire, and repeat the procedure in Step 7.


9. Proceed to the passenger side


rear tire, and repeat the procedure in Step 7.


Vehicle Care


307


10. Proceed to the driver side rear tire, and repeat the procedure in Step 7. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.


11. Turn the ignition switch to


LOCK/OFF.


12. Set all four tires to the


recommended air pressure level as indicated on the Tire and Loading Information label.


Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


Tires are rotated to achieve a uniform wear for all tires. The first rotation is the most important. Anytime unusual wear is noticed, rotate the tires as soon as possible, check for proper tire inflation pressure, and check for damaged tires or wheels. If the unusual wear continues after the rotation, check the wheel alignment. See When It Is Time and Wheel for New Tires 0 309
Replacement 0 313


ii


ii


308


Vehicle Care


Replace the tire if: . The indicators at three or


more places around the tire can be seen.


. There is cord or fabric


showing through the tire's rubber.


. The tread or sidewall is


cracked, cut, or snagged deep enough to show cord or fabric.


. The tire has a bump, bulge,


or split.


. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.


Tire Rotation Tires should be rotated every 12 000 km (7,500 mi). See Maintenance Schedule 0 344


ii


Use this rotation pattern when rotating the tires. Do not include the spare tire in the tire rotation. Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated. See and Vehicle Tire Pressure 0 302
Load Limits 0 205
Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation 0 304
Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications 0 358
{ Warning


ii


ii


ii


ii


Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come (Continued)


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


Warning (Continued)


off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.


Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.


When It Is Time for New Tires Factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.


and Tire Rotation


for additional information.


Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. Some commercial truck tires may not have treadwear indicators. See Tire Inspection 0 307
0 308
The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple factors including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. GM recommends that tires, including the spare if


ii


ii


Vehicle Care


309


equipped, be replaced after six years, regardless of tread wear. The tire manufacture date is the last four digits of the DOT Tire Identification Number (TIN) which is molded into one side of the tire sidewall. The first two digits represent the week (01-52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. This area should be free of grease, gasoline, or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


310


Vehicle Care


Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating. GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number will be followed by MS for mud


ii


and snow. See Tire Sidewall for additional Labeling 0 297
information. GM recommends replacing worn tires in complete sets of four. Uniform tread depth on all tires will help to maintain the performance of the vehicle. Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. If proper rotation and maintenance have been done, all four tires should wear out at about the same time. See Tire for information Rotation 0 308
on proper tire rotation. However, if it is necessary to replace only one axle set of worn tires, place the new tires on the rear axle.


ii


{ Warning


Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death. Only your dealer or authorized tire service center should mount or dismount the tires.


{ Warning


Mixing tires of different sizes, brands, or types may cause loss of control of the vehicle, resulting in a crash or other vehicle damage. Use the correct size, brand, and type of tires on all wheels. This vehicle may have a different size spare than the road tires originally installed on the vehicle. When new, the vehicle included a spare tire and wheel assembly with a


(Continued)


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


Warning (Continued)


similar overall diameter as the road tires and wheels, so it is all right to drive on it. The spare tire was developed for use on this vehicle and will not affect vehicle handling.


{ Warning


Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving. A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.


Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y and ZR speed rated tires. Never exceed the winter


tires’ maximum speed capability when using winter tires with a lower speed rating. If the vehicle tires must be replaced with a tire that does not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction (radial) as the original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed. See Tire Pressure Monitor System 0 303
The Tire and Loading Information label indicates the original equipment tires on the vehicle. See Vehicle Load Limits for the label location and 0 205
more information about the Tire and Loading Information label.


ii


ii


Vehicle Care


311


Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, roll bars, traction control, electronic stability control, or All-Wheel Drive, the performance of these systems can also be affected.


{ Warning


If different sized wheels are used, there may not be an acceptable level of performance and safety if tires not recommended for those wheels are selected. This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems


(Continued)


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


312


Vehicle Care


Warning (Continued)


developed for the vehicle, and have them properly installed by a GM certified technician.


See Buying New Tires 0 310
Accessories and Modifications 0 259


ii


and


ii


Uniform Tire Quality Grading The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter tires, compact spare tires, tires with


nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:


Treadwear 200 Traction AA Temperature A All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.


Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.


Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.


Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all


passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing are not necessary on a regular basis. Consider an alignment check if there is unusual tire wear or the vehicle is significantly pulling to one side or the other. Some slight pull to


Vehicle Care


313


the left or right, depending on the crown of the road and/or other road surface variations such as troughs or ruts, is normal. If the vehicle is vibrating when driving on a smooth road, the tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.


Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


314


Vehicle Care


Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.


Used Replacement Wheels


{ Warning


{ Warning


Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.


Caution


The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis.


Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.


Tire Chains


{ Warning


If the vehicle has 255/65R17 AT, 265/60R18, 265/65R17 or 265/ 70R16 size tires, do not use tire chains. They can damage the vehicle because there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle


(Continued)


Warning (Continued)


parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on the vehicle and tire size combination and road conditions. Follow that manufacturer's instructions. To help avoid damage to the vehicle, drive slowly, readjust, or remove the device if it is contacting the vehicle, and do not spin the vehicle's wheels. If you do find traction devices that will fit, install them on the rear tires.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


Caution


If the vehicle has a tire size other than 255/65R17 AT, 265/60R18, 265/65R17 or 265/70R16, use tire chains only where legal and only when you must. Use chains that are the proper size for the tires. Install them on the tires of the rear axle. Do not use chains on the tires of the front axle. Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer's instructions. If you can hear the chains contacting the vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage the vehicle.


If a Tire Goes Flat It is unusual for a tire to blowout while driving, especially if the tires are maintained properly. If air goes out of a tire, it is much more likely to


leak out slowly. But if there ever is a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.


{ Warning


Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a


(Continued)


Vehicle Care


315


Warning (Continued)


blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.


{ Warning


Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


316


Vehicle Care


ii


If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers 0 146
{ Warning Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall causing injury or death. Find a level place to change the tire. To help prevent the vehicle from moving:


1. Set the parking brake firmly. 2. Put an automatic


transmission in P (Park) or a manual transmission in 1 (First) or R (Reverse).


3. For four-wheel-drive vehicles, be sure the transfer case is in a drive gear– not in N (Neutral).


(Continued)


Warning (Continued)


4. Turn off the engine and do not restart while the vehicle is raised.


5. Do not allow passengers to


remain in the vehicle.


6. Place wheel blocks,


if equipped, on both sides of the tire at the opposite corner of the tire being changed.


2. Flat Tire


The following information explains how to use the jack and change a tire.


Tire Changing


Removing the Spare Tire and Tools


Crew Cab To access and remove the jack and tools:


When the vehicle has a flat tire (2), use the following example as a guide to assist in the placement of the wheel blocks (1), if equipped.


1. Wheel Block (If Equipped)


1. Lift the rear seat to access the


tool bag.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


2. Remove the straps to remove


Extended Cab


the tool bag.


3. Fold the rear seat to access


the jack.


Vehicle Care


317


4. Turn the knob on the jack (2) counterclockwise to lower the jack head to release the jack from its holder.


5. Turn the wing nut (1)


counterclockwise to remove the jack and wheel blocks.


1. Jack Cover 2. Tool Bag Cover


To access and remove the jack and tools: 1. Pull the bottom of the jack


cover (1) forward to remove it.


2. Pull the lower access pocket forward and then upward to remove the tool bag cover (2).


3. Turn the knob on the jack (1) counterclockwise to lower the jack head to release the jack from its holder.


4. Turn the wing nut (2)


counterclockwise to remove the jack and wheel blocks.


5. Turn the wing nut (3)


counterclockwise to remove the tool bag.


Use the jack handle extensions and the wheel wrench to remove the underbody-mounted spare tire.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


318


Vehicle Care


Insert the ignition key, turn, and pull straight out to remove the spare tire lock (8), if equipped.


Do not use the chiseled end of the wheel wrench. Be sure the hoist end of the extension (10) connects to the hoist shaft. The ribbed square end of the extension is used to lower the spare tire.


4. Turn the wheel wrench


counterclockwise to lower the spare tire to the ground. Continue to turn the wheel wrench until the spare tire can be pulled out from under the vehicle.


5. Pull the spare tire out from


under the vehicle.


2. Assemble the wheel wrench (7)


and the two jack handle extensions (6), as shown.


1. Spare Tire (Valve Stem


Pointed Down)


2. Tire/Wheel Retainer 3. Hoist Cable 4. Hoist Assembly 5. Hoist Shaft 6. Jack Handle Extensions 7. Wheel Wrench 8. Spare Tire Lock (If


Equipped)


9. Hoist Shaft Access Hole 10. Hoist End of Extension Tool 1. Open the spare tire lock cover


on the bumper.


3.


Insert the hoist end (open end) (10) of the extension through the hole (9) in the rear bumper.


6. Tilt the tire toward the vehicle


with some slack in the cable to access the tire/wheel retainer.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


Vehicle Care


319


5. Wheel Wrench


1. Do a safety check before


proceeding. See If a Tire Goes Flat 0 315


ii


2.


If the wheel has a center cap that covers the lug nuts, place the chisel end of the wheel wrench in each of the slots in the cap, and gently pry it out.


3. Use the wheel wrench and turn


it counterclockwise to loosen the wheel nuts. Do not remove the wheel nuts yet.


Tilt the retainer and pull it through the center of the wheel along with the cable and spring.


7. Put the spare tire near the


flat tire.


Removing the Flat Tire and Installing the Spare Tire Use the following pictures and instructions to remove the flat tire and raise the vehicle.


1. Jack 2. Wheel Blocks 3. Jack Handle 4. Jack Handle Extensions


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


320


Vehicle Care


Front Position


Rear Position


4. Position the jack under the vehicle, as shown. If the flat tire is on the front of the vehicle, position the jack on the depression in the vehicle's frame, behind the flat tire.


5.


If the flat tire is on the rear, position the jack under the rear axle about 5 cm (2 in) inboard of the shock absorber bracket. Make sure that the jack head is positioned so that the rear axle is resting securely between the grooves that are on the jack head.


{ Warning


Getting under a vehicle when it is lifted on a jack is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.


{ Warning


Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.


6. Turn the wheel wrench


clockwise to raise the vehicle. Raise the vehicle far enough off the ground so there is enough room for the spare tire to fit under the wheel well.


Chevrolet Colorado Owner Manual (GMNA-Localizing-U.S/Canada/Mexico- 9159327) - 2016 - crc - 8/28/15


Vehicle Care


321


11. Tighten each wheel nut by hand. Then use the wheel wrench to tighten the nuts until the wheel is held against the hub.


12. Turn the wheel wrench


counterclockwise to lower the vehicle. Lower the jack completely.


{ Warning


If wheel studs are damaged, they can break. If all the studs on a wheel broke, the wheel could come off and cause a crash. If any stud is damaged because of a loose-running wheel, it could be that all of the studs are damaged. To be sure, replace all studs on the wheel. If the stud holes in a wheel have become larger, the wheel could collapse in operation. Replace any wheel if its stud holes have become larger or distorted in any way. Inspect hubs and hub‐piloted wheels for damage. Because of loose


(Continued)


7. Remove all the wheel nuts and


8. Remove any rust or dirt from


take off the flat tire. { Warning


Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.


9.


the wheel bolts, mounting surfaces, and spare wheel. Install the spare tire. { Warning

Loading...
x