2015 Chevrolet Colorado Owners Manual

10 minutes or until any door is opened. The radio continues to work for up to 10 minutes or until the driver door is opened.

Accessory Power Outlets (APOs) The vehicle may have APOs in several locations. See Power Outlets on page 5-5. The APOs in the console or center seat position are powered by RAP. They will continue to work for up to 10 minutes after the key is turned from ON/RUN to LOCK/OFF, or until the driver door is opened. The APOs on the center stack come from the factory powered directly from the vehicle battery, and supply accessory power at all times, regardless of ignition key position.

If electronic items are left plugged into these APOs for long periods of time with the vehicle off, the vehicle battery could be drained. The vehicle may not start if the battery is allowed to drain for an extended period of time.

Engine Coolant Heater

2.5L L4 engine shown, 3.6L

V6 engine similar

The engine heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (26,1)

9-26

Driving and Operating

−18°C (0°F). Vehicles with an engine heater should be plugged in at least four hours before starting. An internal thermostat in the plug-end of the cord may exist, which will prevent engine coolant heater operation at temperatures above −18°C (0°F). To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the

electrical cord. The cord is secured to the engine with a clip. Carefully remove the cord from the clip. Check the heater cord for damage. If it is damaged, do not use it. See your dealer for a replacement. Inspect the cord for damage yearly.

3. Plug the cord into a normal, grounded 110-volt AC outlet.

{ Warning

Improper use of the heater cord or an extension cord can damage the cord and may result in overheating and fire.

. Plug the cord into a

three-prong electrical utility receptacle that is protected by a ground fault detection function. An ungrounded outlet could cause an electric shock.

. Use a weatherproof,

heavy-duty, 15 amp-rated extension cord if needed. Failure to use the recommended extension cord in good operating condition, or using a damaged heater or extension cord, could make it (Continued)

Warning (Continued)

overheat and cause a fire, property damage, electric shock, and injury.

. Do not operate the vehicle

with the heater cord permanently attached to the vehicle. Possible heater cord and thermostat damage could occur.

. While in use, do not let the

heater cord touch vehicle parts or sharp edges. Never close the hood on the heater cord.

. Before starting the vehicle,

unplug the cord, reattach the cover to the plug, and securely fasten the cord. Keep the cord away from any moving parts.

4. Before starting the engine, be

sure to unplug and store the cord as it was before to keep it

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (27,1)

Driving and Operating

9-27

away from moving engine parts. If you do not, it could be damaged.

The length of time the heater should remain plugged in depends on several factors. Ask a dealer in the area where you will be parking the vehicle for the best advice on this.

Shifting Into Park { Warning

It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, use the steps that follow. With four-wheel drive, if the transfer case is in N (Neutral), the vehicle will be

(Continued)

Warning (Continued)

free to roll, even if the shift lever is in P (Park). Be sure the transfer case is in a drive gear. If towing a trailer, see Driving Characteristics and Towing Tips on page 9-58.

1. Hold the brake pedal down, then

set the parking brake. See Parking Brake on page 9-42.

2. Hold the button on the shift lever

and push the lever toward the front of the vehicle into P (Park).

3. Be sure the transfer case (if

equipped) is in a drive gear — not in N (Neutral).

4. Turn the ignition key to

LOCK/OFF.

5. Remove the key and take it with you. If you can leave the vehicle with the ignition key in your hand, the vehicle is in P (Park).

Leaving the Vehicle with the Engine Running

{ Warning

It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set. If you have four-wheel drive and the transfer case is in N (Neutral), the vehicle will be free to roll, even if the shift lever is in P (Park). So be sure the transfer case is in a drive gear — not in N (Neutral). And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Do not leave the vehicle with the engine running unless you have to.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (28,1)

9-28

Driving and Operating

If you have to leave the vehicle with the engine running, be sure the vehicle is in P (Park) and the parking brake is firmly set before you leave it. After you move the shift lever into P (Park), hold the regular brake pedal down. Then, see if you can move the shift lever away from P (Park) without pressing the button on the shift lever. If you can, it means that the shift lever was not fully locked into P (Park). Torque Lock If you are parking on a hill and you do not shift the transmission into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it difficult to pull the shift lever out of P (Park). This is called torque lock. To prevent torque lock, set the parking brake and then shift into P (Park) properly before you leave the driver seat. To find out how, see Shifting Into Park on page 9-27.

When you are ready to drive, move the shift lever out of P (Park) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission. You will then be able to pull the shift lever out of P (Park).

Shifting out of Park This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: . Prevent ignition key removal

unless the shift lever is in P (Park).

. Prevent movement of the shift

lever out of P (Park), unless the ignition is in ON/RUN and the regular brake pedal is applied.

The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9 volt) battery. If the vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 10-74. To shift out of P (Park): 1. Apply the brake pedal. 2. Move the shift lever to the

desired position.

If you still are unable to shift out of P (Park): 1. Ease the pressure on the shift

lever.

2. While holding down the brake pedal, press the shift lever all the way into P (Park).

3. Move the shift lever to the

desired position.

If you are still having a problem shifting, then have the vehicle serviced soon.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (29,1)

Parking over Things That Burn

{ Warning

Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn.

This vehicle may have the Safety Belt Assurance System, which may prevent the vehicle from shifting out of P (Park). See Safety Belt Messages on page 5-30.

Parking If the vehicle has a manual transmission, before you get out of the vehicle, move the shift lever into R (Reverse), and firmly apply the parking brake. Once the shift lever has been placed into R (Reverse) with the clutch pedal pressed in, turn the ignition key to LOCK/OFF, remove the key and release the clutch. If you are parking on a hill, or if the vehicle is pulling a trailer, see Driving Characteristics and Towing Tips on page 9-58.

Driving and Operating

9-29

Engine Exhaust { Warning

Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if:

. The vehicle idles in areas

with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes).

. The exhaust smells or

sounds strange or different.

. The exhaust system leaks

due to corrosion or damage. . The vehicle exhaust system

has been modified, damaged, or improperly repaired.

(Continued)

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (30,1)

9-30

Driving and Operating

Running the Vehicle While Parked It is better not to park with the engine running. If the vehicle is left with the engine running, follow the proper steps to be sure the vehicle will not move. See Shifting Into Park on page 9-27
and Engine Exhaust on page 9-29. If the vehicle has a manual transmission, see Parking on page 9-29. If parking on a hill and pulling a trailer, see Driving Characteristics and Towing Tips on page 9-58.

Warning (Continued)

. There are holes or openings

in the vehicle body from damage or aftermarket modifications that are not completely sealed.

If unusual fumes are detected or if it is suspected that exhaust is coming into the vehicle:

. Drive it only with the windows

completely down.

. Have the vehicle repaired

immediately.

Never park the vehicle with the engine running in an enclosed area such as a garage or a building that has no fresh air ventilation.

Automatic Transmission If equipped, there is an electronic shift lever position indicator within the instrument cluster. This display comes on when the ignition key is turned to the ON/RUN position.

P (Park): This position locks the rear wheels. It is the best position to use when starting the engine because the vehicle cannot move easily. When parked on a hill, especially when the vehicle has a

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (31,1)

heavy load, you might notice an increase in the effort to shift out of P (Park). See “Torque Lock” under Shifting Into Park on page 9-27.

{ Warning

It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park). See Shifting Into Park on page 9-27 and Driving Characteristics and Towing Tips on page 9-58.

{ Warning

If you have four-wheel drive, the vehicle will be free to roll — even if the shift lever is in P (Park) — if the transfer case is in N (Neutral). So, be sure the transfer case is in a drive gear, Two-Wheel Drive High or Four-Wheel Drive High or Four-Wheel Drive Low — not in N (Neutral). See Shifting Into Park on page 9-27.

R (Reverse): Use this gear to back up.

{ Caution

Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.

Driving and Operating

9-31

To rock the vehicle back and forth to get out of snow, ice, or sand without damaging the transmission, see If the Vehicle Is Stuck on page 9-13. N (Neutral): In this position, the engine does not connect with the wheels. To restart when you are already moving, use N (Neutral) only. Also, use N (Neutral) when the vehicle is being towed.

{ Warning

Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is firmly on the brake pedal, the vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while the engine is running at high speed.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (32,1)

9-32

Driving and Operating

{ Caution Shifting out of P (Park) or N (Neutral) with the engine running at high speed may damage the transmission. The repairs would not be covered by the vehicle warranty. Be sure the engine is not running at high speed when shifting the vehicle.

D (Drive): This position is for normal driving. It provides the best fuel economy. If you need more power for passing, and you are: . Going less than about 55 km/h (35 mph), push the accelerator pedal about halfway down.

. Going about 55 km/h (35 mph) or

more, push the accelerator all the way down. By doing this, the vehicle shifts down to the next gear and has more power.

D (Drive) can be used when towing a trailer, carrying a heavy load, driving on steep hills, or driving off-road. Shift the transmission to a lower gear selection if the transmission shifts too often. Downshifting the transmission in slippery road conditions could result in skidding. See “Skidding” under Loss of Control on page 9-5. The vehicle has a shift stabilization feature that adjusts the transmission shifting to the current driving conditions in order to reduce rapid upshifts and downshifts. This shift stabilization feature is designed to determine, before making an upshift, if the engine is able to maintain vehicle speed by analyzing things such as vehicle speed, throttle position, and vehicle load. If the shift stabilization feature determines that a current vehicle speed cannot be maintained, the transmission does not upshift and instead holds the current gear.

In some cases, this could appear to be a delayed shift, however the transmission is operating normally. The transmission uses adaptive shift controls. The adaptive shift control process continually compares key shift parameters to pre-programmed ideal shifts stored in the transmission’s computer. The transmission constantly makes adjustments to improve vehicle performance according to how the vehicle is being used, such as with a heavy load or when the temperature changes. During this adaptive shift control process, shifting might feel different as the transmission determines the best settings. When temperatures are very cold, the transmission's gear shifting could be delayed providing more stable shifts until the engine warms up. Shifts could be more noticeable with a cold transmission. This difference in shifting is normal.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (33,1)

M (Manual Mode): This position allows selection of a range of gears appropriate for current driving conditions. See “Range Selection Mode” under Manual Mode on page 9-33.

{ Caution

Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will not be covered by the vehicle warranty. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place.

Driving and Operating

9-33

when driving on downhill grades by using the engine and transmission to slow the vehicle.

To use this feature: 1. Move the shift lever to

M (Manual Mode).

Manual Mode

Range Selection Mode

2. Tap the plus/minus buttons on

the shift lever to select the desired range of gears for current driving conditions.

When the shift lever is moved from D (Drive) to M (Manual Mode), a number displays next to the M, indicating the current transmission range. This number is the highest gear that the transmission will command while operating in M (Manual Mode). All gears below that number are available. As driving conditions change, the transmission can automatically shift to lower gears. For example, when M5 is selected, 1 (First) through 5 (Fifth) gears are automatically shifted by the transmission, but 6 (Sixth) cannot be used until the plus/minus button on the shift lever is used to change to the range.

Normal Mode Grade Braking Normal Mode Grade Braking is enabled when the vehicle is started, but is not enabled in Range Selection Mode. It assists in maintaining desired vehicle speeds

If equipped, Range Selection Mode helps control the vehicle's transmission and vehicle speed while driving downhill or towing a trailer by letting you select a desired range of gears.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (34,1)

9-34

Driving and Operating

When the shift lever is moved from D (Drive) to M (Manual Mode), a downshift may occur. The gear that the transmission is operating in when the shift lever is moved from D (Drive) to M (Manual Mode) determines if a downshift occurs. See the following chart.

Gear before shifting from D (Drive) to M (Manual Mode) Range after shifting from D (Drive) to M (Manual Mode)

6th

5th

4th

3rd

2nd

1st

M4

M4

M3

M2

M2

M1

Low Traction Mode Low Traction Mode assists in vehicle acceleration when road conditions are slippery, such as with ice or snow. While the vehicle is at a stop, select M2 using Range Selection Mode. This will limit torque to the wheels and help to prevent the tires from spinning.

Grade Braking is not available when Range Selection Mode is active. See Tow/Haul Mode on page 9-35. While using Range Selection Mode, cruise control and the Tow/Haul Mode can be used.

{ Caution

Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will not be covered by the vehicle warranty. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (35,1)

Turn the Tow/Haul Mode on and off by pressing the button on the center stack. When the Tow/Haul Mode is enabled, a light on the instrument cluster will come on. See Tow/Haul Mode Light on page 5-17 and Hill and Mountain Roads on page 9-11. Also see “Tow/Haul Mode” under Towing Equipment on page 9-64.

Tow/Haul Mode

If equipped, Tow/Haul Mode adjusts the transmission shift pattern to reduce shift cycling. This provides increased performance, vehicle control; and transmission cooling when driving down steep hills or mountain grades, towing, or hauling heavy loads.

Driving and Operating

9-35

Manual Transmission

If equipped with a manual transmission, this is the shift pattern.

{ Caution

Do not rest your hand on the shift lever while driving. The pressure could cause premature wear in the transmission. The repairs would not be covered by the vehicle warranty.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (36,1)

9-36

Driving and Operating

{ Caution

Do not rest your foot on the clutch pedal while driving or while stopped. The pressure can cause premature wear in the clutch. The repairs would not be covered by the vehicle warranty.

To operate the manual transmission: 1 (First): Press the clutch pedal fully to the pedal stop and shift into 1 (First). Then, slowly let up on the clutch pedal as you slowly press down on the accelerator pedal. You can shift into 1 (First) when you are going less than 30 km/h (20 mph). If you have come to a complete stop and it is hard to shift into 1 (First), put the shift lever in Neutral and let up on the clutch. Then press the clutch pedal back down and shift into 1 (First).

2 (Second): Press the clutch pedal fully to the pedal stop while letting up on the accelerator pedal and shift into 2 (Second). Then, slowly let up on the clutch pedal as you press the accelerator pedal. 3 (Third), 4 (Fourth), 5 (Fifth) and 6 (Sixth): Shift into 3 (Third), 4 (Fourth), 5 (Fifth) and 6 (Sixth) the same way you do for 2 (Second). Slowly let up on the clutch pedal as you press the accelerator pedal. To stop, let up on the accelerator pedal and press the brake pedal. Just before the vehicle stops, press the clutch pedal and the brake pedal, and shift to Neutral. Neutral: Use this position when you start or idle the engine. R (Reverse): To back up, press the clutch pedal. After the vehicle stops, press down on shift lever in the 3–4
Neutral position, then shift into R (Reverse). If it is hard to shift, let

the shift lever return to the 3–4
Neutral position and release the clutch pedal. Then follow the steps again to shift into R (Reverse). Slowly let up on the clutch pedal as you press the accelerator pedal.

{ Caution

Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.

Use R (Reverse), along with the parking brake, for parking the vehicle.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (37,1)

Shift Speeds

Drive Systems

{ Warning If you skip a gear when downshifting, you could lose control of the vehicle. You could injure yourself or others. Do not shift down more than one gear at a time when downshifting.

Shift Indicator

This light comes on when an up-shift is recommended for best fuel economy. The number displayed with the arrow indicates the recommended gear.

Four-Wheel Drive If equipped, four-wheel drive engages the front axle for extra traction. Read the appropriate section for transfer case operation before using.

{ Caution

Driving on clean, dry pavement in four-wheel drive for an extended period of time may cause premature wear on the system. The damage would not be covered by the vehicle warranty.

Driving on clean, dry pavement in four-wheel drive may: . Cause a vibration to be felt in

the steering system.

. Cause tires to wear faster. . Make the transfer case harder to shift, and cause it to run noisier.

Driving and Operating

9-37

{ Warning

Shifting the transfer case to N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in N (Neutral). See Parking Brake on page 9-42.

{ Caution

Extended high-speed operation in 4 n may damage or shorten the life of the drivetrain.

Engagement noise and bump when shifting between 4 n and 4 m or from N (Neutral), with the engine running, is normal.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (38,1)

9-38

Driving and Operating

Shifting into 4 n will turn Traction Control and StabiliTrak® off. See Traction Control/Electronic Stability Control on page 9-43. Electronic Transfer Case

Use the transfer case knob, next to the steering wheel, to shift into and out of four-wheel drive for extra traction. Indicator lights on the knob show which setting the transfer case is in. The N (Neutral) indicator is on the face of the knob. The indicator lights display briefly when the ignition is

turned on, and one will stay on. If the lights display momentarily when the ignition is in ON/RUN, but none stay on, the knob may have been turned while the vehicle was off. To see the indicator, turn the knob to another position so that it matches the actual transfer case setting. If no lights display, take the vehicle to your dealer for service. An indicator light flashes while shifting and until the shift is complete. If the transfer case cannot complete a requested shift, it will return to the last chosen setting. Turn the control back to the previous setting to see the indicator light.

{ Caution

Shifting the transmission into gear before the requested mode indicator light has stopped flashing could damage the transfer case.

The settings are: N (Neutral): Use only when the vehicle needs to be towed. See Recreational Vehicle Towing on page 10-76 or Towing the Vehicle on page 10-76. 2 m (Two-Wheel Drive High): Use for driving on most streets and highways. The front axle is not engaged. This setting provides the best fuel economy. 4 n (Four-Wheel Drive Low): This setting engages the front axle and delivers extra torque. Choose 4 n if driving off-road in deep sand, deep mud, or deep snow, and while climbing or descending steep hills. When engaged, keep vehicle speed below 72 km/h (45 mph). Shifting into 4 n will turn Traction Control and StabiliTrak off. See Traction Control/Electronic Stability Control on page 9-43.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (39,1)

4 m (Four-Wheel Drive High): Use when extra traction is needed. The front axle engages and helps when driving on snowy or icy roads, and when off-roading. The vehicle can be shifted from 2 m to 4 m while the vehicle is moving. Shifting Into 4 m Turn the knob to 4 m at any speed up to 121 km/h (75 mph), except from 4 n. The indicator light will flash while shifting and will remain on the selected setting. Shifting Into 2 m Turn the knob to 2 m at any speed, except when shifting from 4 n.

Driving and Operating

9-39

Shifting Out of 4 n 1. To shift out of 4 n the vehicle

must be stopped or moving less than 5 km/h (3 mph) with the transmission in N (Neutral) and the ignition in ON/RUN. It is best for the vehicle to be moving 1.6 to 3.2 km/h (1 to 2 mph).

2. Turn the knob to 4 m or 2 m. Wait for the 4 m or 2 m indicator light to stop flashing before shifting the transmission into gear.

If the transmission is in gear and/or moving more than 5 km/h (3 mph), the 4 m or 2 m indicator light will flash for 30 seconds, but will not complete the shift. With the vehicle moving less than 5 km/h (3 mph), and the transmission in N (Neutral), attempt the shift again.

Shifting Into 4 n When 4 n is engaged, vehicle speed should be kept below 72 km/h (45 mph). 1. The ignition must be in ON/RUN and the vehicle must be stopped or moving less than 5 km/h (3 mph) with the transmission in N (Neutral). It is best for the vehicle to be moving 1.6 to 3.2 km/h (1 to 2 mph).

2. Turn the knob to 4 n. Wait for the 4 n indicator light to stop flashing before shifting the transmission into gear.

If the transmission is in gear and/or moving more than 5 km/h (3 mph), the 4 n indicator light will flash for 30 seconds and not complete the shift. After 30 seconds the transfer case will shift to 4 m. Turn the knob to 4 m to see the indicator. With the vehicle moving less than 5 km/h (3 mph), and the transmission in N (Neutral), attempt the shift again.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (40,1)

9-40

Driving and Operating

Shifting Into N (Neutral) To shift: 1. Park the vehicle on a level

surface.

2. Set the parking brake and press

and hold the brake pedal. See Parking Brake on page 9-42.

3. Start the vehicle or turn the

ignition to ON/RUN.

4. Shift the transmission to

N (Neutral).

5. Shift the transfer case to 2 m. 6. Turn the transfer case knob

clockwise to N (Neutral) until it stops and hold it there until the N (Neutral) light starts blinking. This will take at least 10 seconds. Then slowly release the dial to the 4 n position. The N (Neutral) light will come on when the transfer case shift to N (Neutral) is complete.

7. With the engine running, verify

that the transfer case is in N (Neutral) by shifting the transmission to R (Reverse), then to D (Drive). There should be no movement of the vehicle while shifting the transmission.

8. Turn the engine off, and the

ignition to ACC/ACCESSORY.

9. Place the transmission shift

lever in P (Park). See Recreational Vehicle Towing on page 10-76.

10. Turn the ignition to LOCK/OFF.

Shifting Out of N (Neutral) To shift: 1. Set the parking brake and apply

the brake pedal.

2. Turn the ignition to ON/RUN with

the engine off.

3. Shift the transmission to

N (Neutral).

4. Turn the transfer case knob

to 2 m. After the transfer case has shifted out of N (Neutral), the N (Neutral) light will go out. 5. Release the parking brake.

{ Caution

Shifting the transmission into gear before the requested mode indicator light has stopped flashing could damage the transfer case.

6. Start the engine and shift the

transmission to the desired gear.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (41,1)

Driving and Operating

9-41

Brakes

Antilock Brake System (ABS) This vehicle has ABS, an advanced electronic braking system that helps prevent a braking skid. When the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little. This is normal.

If there is a problem with ABS, this warning light stays on. See Antilock Brake System (ABS) Warning Light on page 5-17.

If driving safely on a wet road and it becomes necessary to slam on the brakes and continue braking to avoid a sudden obstacle, a computer senses the wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel. ABS can change the brake pressure to each wheel, as required, faster than any driver could. This can help you steer around the obstacle while braking hard. As the brakes are applied, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle

suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let ABS work. You may hear the ABS pump or motor operating and feel the brake pedal pulsate. This is normal. Braking in Emergencies ABS allows you to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (42,1)

9-42

Driving and Operating

Parking Brake

Set the parking brake by holding the regular brake pedal down, then pushing down the parking brake pedal. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 5-16.

{ Caution

Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving.

To release the parking brake, hold the regular brake pedal down, then push down momentarily on the parking brake pedal until you feel the pedal release. Slowly pull your foot up off the parking brake pedal. If the parking brake is not released when you begin to drive, the brake system warning light will flash and a chime will sound warning you that the parking brake is still on. If you are towing a trailer and are parking on a hill, see Driving Characteristics and Towing Tips on page 9-58.

Brake Assist The Brake Assist feature is designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability system hydraulic brake control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the vehicle. The stability system hydraulic brake control module increases brake pressure at each corner of the vehicle until the ABS activates. Minor brake pedal pulsation or pedal movement during this time is normal and the driver should continue to apply the brake pedal as the driving situation dictates. The Brake Assist feature will automatically disengage when the brake pedal is released or brake pedal pressure is quickly decreased.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (43,1)

Hill Start Assist (HSA) This vehicle has an HSA feature, which may be useful when the vehicle is stopped on a grade sufficient enough to activate HSA. This feature is designed to prevent the vehicle from rolling, either forward or rearward, during vehicle drive off. After the driver completely stops and holds the vehicle in a complete standstill on a grade, HSA will be automatically activated. During the transition period between when the driver releases the brake pedal and starts to accelerate to drive off on a grade, HSA holds the braking pressure for a maximum of two seconds to ensure that there is no rolling. The brakes will automatically release when the accelerator pedal is applied within the two-second window. It will not activate if the vehicle is in a drive gear and facing downhill, or if the vehicle is facing uphill and in R (Reverse).

Driving and Operating

9-43

Ride Control Systems

Traction Control/ Electronic Stability Control

System Operation The vehicle has a Traction Control System (TCS) and StabiliTrak®, an electronic stability control system. These systems help limit wheel slip and assist the driver in maintaining control, especially on slippery road conditions. TCS activates if it senses that any of the drive wheels are spinning or beginning to lose traction. When this happens, TCS applies the brakes to the spinning wheels and reduces engine power to limit wheel spin. StabiliTrak activates when the vehicle senses a difference between the intended path and the direction the vehicle is actually traveling. StabiliTrak selectively applies braking pressure to any one of the

vehicle wheel brakes to assist the driver in keeping the vehicle on the intended path. If cruise control is being used and traction control or StabiliTrak begins to limit wheel spin, cruise control will disengage. Cruise control may be turned back on when road conditions allow. Both systems come on automatically when the vehicle is started and begins to move. The systems may be heard or felt while they are operating or while performing diagnostic checks. This is normal and does not mean there is a problem with the vehicle. It is recommended to leave both systems on for normal driving conditions, but it may be necessary to turn TCS off if the vehicle gets stuck in sand, mud, ice, or snow. See If the Vehicle Is Stuck on page 9-13 and “Turning the Systems Off and On” later in this section.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (44,1)

9-44

Driving and Operating

When the transfer case (if equipped) is in Four-Wheel Drive Low, the stability system is automatically disabled, and g comes on in the instrument cluster. Both traction control and StabiliTrak are automatically disabled in this condition.

The indicator light for both systems is in the instrument cluster. This light will:

Flash when TCS is limiting wheel spin. Flash when StabiliTrak is activated. Turn on and stay on when either system is not working.

If either system fails to turn on or to activate, a message displays in the Driver Information Center (DIC), and d comes on and stays on to indicate that the system is inactive and is not assisting the driver in maintaining control. The vehicle is safe to drive, but driving should be adjusted accordingly. If d comes on and stays on: 1. Stop the vehicle. 2. Turn the engine off and wait

15 seconds.

3. Start the engine. Drive the vehicle. If d comes on and stays on, the vehicle may need more time to diagnose the problem. If the condition persists, see your dealer.

Turning the Systems Off and On

The button for TCS and StabiliTrak is on the center stack.

{ Caution

Do not repeatedly brake or accelerate heavily when TCS is off. The vehicle driveline could be damaged.

To turn off only TCS, press and release the g button. The Traction Off Light i displays in the instrument cluster. To turn TCS on again, press and release the g

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (45,1)

Driving and Operating

9-45

button. The Traction Off Light i displayed in the instrument cluster will turn off. If TCS is limiting wheel spin when the g button is pressed, the system will not turn off until the wheels stop spinning. To turn off both TCS and StabiliTrak, press and hold the g button until the Traction Off Light i and StabiliTrak Off Light g come on and stay on in the instrument cluster. To turn TCS and StabiliTrak on again, press and release the g button. The Traction Off Light i and StabiliTrak Off Light g in the instrument cluster turn off. StabiliTrak will automatically turn on if the vehicle exceeds 56 km/h (35 mph). Traction control will remain off until the driver presses the g button or the ignition is cycled Off then On.

Adding accessories can affect the vehicle performance. See Accessories and Modifications on page 10-3.

Hill Descent Control (HDC) If equipped, HDC can be used when driving downhill. It sets and maintains vehicle speed while descending a very steep incline in a forward or reverse gear. The HDC switch is on the center stack, below the climate controls. Press 5 to enable or disable HDC. Vehicle speed must be below 60 km/h (37 mph).

The HDC light displays on the instrument cluster when enabled.

HDC can maintain vehicle speeds between 4 and 30 km/h (3 and 19 mph) on an incline greater than or equal to a 10% grade. A blinking HDC light indicates that the system is actively applying the brakes to maintain vehicle speed. When HDC is set, that is the initial set speed. It can be increased or decreased by applying the accelerator or brake pedal. Smaller HDC speed control adjustments are accomplished using the cruise up or down buttons. Each tap of the +RES will increase the set speed by 0.8 km/h (0.5 mph), while each tap of the SET– will decrease the set speed by 0.8 km/h (0.5 mph). This adjusted speed becomes the new set speed. HDC will remain enabled between 30 and 60 km/h (19 and 37 mph), however vehicle speed cannot be set or maintained in this range.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (46,1)

9-46

Driving and Operating

It will automatically disable if the vehicle speed is above 80 km/h (50 mph) or above 60 km/h (37 mph) for at least 30 seconds. 5
must be pressed again to re-enable HDC. When enabled, if the vehicle is at a speed above 30 km/h (19 mph) and less than 60 km/h (37 mph), a DIC message will display instructing the driver to reduce speed for HDC operation. Cruise control will not function while HDC is enabled and vehicle speed is below 40 km/h (25 mph).

Cruise Control With cruise control a speed of about 40 km/h (25 mph) or more can be maintained without keeping your foot on the accelerator. Cruise control does not work at speeds below about 40 km/h (25 mph).

{ Warning

Cruise control can be dangerous where you cannot drive safely at a steady speed. Do not use cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.

If equipped with a manual transmission, the cruise control will remain active when the gears are shifted. The cruise is deactivated if the clutch is pressed for several seconds. If the cruise control is being used and the Traction Control (TCS) system or StabiliTrak begins to limit wheel spin, the cruise control will automatically disengage. See Traction Control/Electronic Stability Control on page 9-43. If a collision alert occurs when cruise control is activated, cruise control is disengaged. See Forward Collision Alert (FCA) System on page 9-49. When road conditions allow you to safely use it again, cruise control can be turned back on. If the brakes are applied, the cruise control disengages.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (47,1)

Driving and Operating

9-47

SET− (Set/Coast): Press briefly to set the speed and activate cruise control. If cruise control is already active, use to decrease vehicle speed. * (Cancel): Press to disengage cruise control without erasing the set speed from memory.

Setting Cruise Control If 5 is on when not in use, SET− or +RES could get pressed and go into cruise when not desired. Keep 5
off when cruise is not being used. 1. Press 5 to turn the cruise

system on.

2. Get up to the desired speed. 3. Press and release SET−. 4. Remove foot from the

accelerator.

The cruise control indicator on the instrument cluster turns green after cruise control has been set to the desired speed. See Instrument Cluster on page 5-8.

Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied or * is pressed, the cruise control is disengaged without erasing the set speed from memory. Once the vehicle speed reaches about 40 km/h (25 mph) or more, press the +RES button briefly. The vehicle returns to the previous set speed.

Increasing Speed While Using Cruise Control If the cruise control system is already activated: . Press and hold +RES until the desired speed is reached, then release it. To increase vehicle speed in small increments, briefly press +RES. For each press, the vehicle goes about 1.6 km/h (1 mph) faster.

5 (On/Off): Press to turn the system on or off. A white indicator comes on in the instrument cluster when cruise control is turned on. +RES (Resume/Accelerate): If there is a set speed in memory, press briefly to resume to that speed or press and hold to accelerate. If cruise control is already active, use to increase vehicle speed.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (48,1)

9-48

Driving and Operating

The speedometer reading can be displayed in either English or metric units. See Driver Information Center (DIC) on page 5-22. The increment value used depends on the units displayed.

Reducing Speed While Using Cruise Control If the cruise control system is already activated: . Press and hold SET– until the

desired lower speed is reached, then release it. To slow down in small increments, briefly press SET– . For each press, the vehicle goes about 1.6 km/h (1 mph) slower.

The speedometer reading can be displayed in either English or metric units. See Driver Information Center (DIC) on page 5-22. The increment value used depends on the units displayed.

Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the previous set cruise speed. While pressing the accelerator pedal or shortly following the release to override cruise control, briefly pressing the SET– button will result in cruise control set to the current vehicle speed.

Using Cruise Control on Hills How well the cruise control will work on hills depends on the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain your speed. When going downhill, you might have to brake or shift to a lower gear to keep your speed down. If the brake pedal is applied, cruise control will disengage.

Ending Cruise Control There are four ways to end cruise control: . Step lightly on the brake pedal. . Press *. . Press the clutch pedal for

several seconds or shift the transmission to N (Neutral). To turn off cruise control, press 5.

Erasing Speed Memory The cruise control set speed is erased from memory if 5 is pressed or if the ignition is turned off.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (49,1)

Driver Assistance Systems

Forward Collision Alert (FCA) System If equipped, the FCA system may help to avoid or reduce the harm caused by front-end crashes. When approaching a vehicle ahead too quickly, FCA provides a red flashing alert on the windshield, and rapidly beeps. FCA also lights an amber visual alert if following another vehicle much too closely. FCA detects vehicles within a distance of approximately 60 m (197 ft) and operates at speeds above 40 km/h (25 mph). { Warning

FCA is a warning system and does not apply the brakes. When approaching a slower-moving or

(Continued)

Warning (Continued)

stopped vehicle ahead too rapidly, or when following a vehicle too closely, FCA may not provide a warning with enough time to help avoid a crash. FCA does not warn of pedestrians, animals, signs, guardrails, bridges, construction barrels, or other objects. Be ready to take action and apply the brakes. For more information, see Defensive Driving on page 9-3.

FCA can be disabled with the FCA steering wheel control. Detecting the Vehicle Ahead

Driving and Operating

9-49

FCA warnings will not occur unless the FCA system detects a vehicle ahead. When a vehicle is detected, the vehicle ahead indicator will display green. Vehicles may not be detected on curves, highway exit ramps, or hills; or due to poor visibility. FCA will not detect another vehicle ahead until it is completely in the driving lane.

{ Warning

FCA does not provide a warning to help avoid a crash, unless it detects a vehicle. FCA may not detect a vehicle ahead if the FCA sensor is blocked by dirt, snow, or ice, or if the windshield is damaged. It may also not detect a vehicle on winding or hilly roads, or in conditions that can limit visibility such as fog, rain, or snow, or if the headlamps or windshield are not cleaned or in

(Continued)

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (50,1)

9-50

Driving and Operating

Warning (Continued)

proper condition. Keep the windshield, headlamps, and FCA sensors clean and in good repair.

Collision Alert

When your vehicle approaches another detected vehicle too rapidly, the red lights will flash on the windshield. Also, eight rapid high-pitched beeps will sound from the front. When this Collision Alert occurs, the brake system may prepare for driver braking to occur more rapidly which can cause a brief, mild deceleration. Continue to apply the brake pedal as needed. Cruise control may be disengaged when the Collision Alert occurs.

Tailgating Alert

The vehicle ahead indicator will display amber when you are following a detected vehicle ahead much too closely. Selecting the Alert Timing The Collision Alert control is on the steering wheel. Press [ to set the FCA timing to Far, Medium, Near, or Off. The first button press shows the current setting on the DIC. Additional button presses will change this setting. The chosen setting will remain until it is changed and will affect the timing of both the Collision Alert and the Tailgating Alert features. The timing of both alerts will vary based on vehicle speed. The faster the vehicle speed, the farther away the alert will occur.

Consider traffic and weather conditions when selecting the alert timing. The range of selectable alert timing may not be appropriate for all drivers and driving conditions. Unnecessary Alerts FCA may provide unnecessary alerts for turning vehicles, vehicles in other lanes, objects that are not vehicles, or shadows. These alerts are normal operation and the vehicle does not need service. Cleaning the System If the FCA system does not seem to operate properly, cleaning the outside of the windshield in front of the rearview mirror, and cleaning the front of the vehicle, may correct the issue.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (51,1)

Rear Vision Camera (RVC)

{ Warning

The RVC system does not display children, pedestrians, bicyclists, crossing traffic, animals, or any other object located outside the camera's field of view, below the bumper, or under the vehicle. Perceived distances may be different from actual distances. Do not back the vehicle using only the RVC screen. Failure to use proper care before backing may result in injury, death, or vehicle damage. Always check behind and around the vehicle before backing.

If equipped, the RVC system is designed to help the driver when backing up by displaying a view of the area behind the vehicle. When the key is in ON/RUN and the driver shifts the vehicle into R (Reverse),

the video image automatically appears on the infotainment screen. The infotainment screen goes to the previous screen after approximately four seconds once the vehicle is shifted out of R (Reverse). To see the previous screen sooner, do one of the following: . Press a hard key on the

infotainment system.

. Shift into P (Park).

Guidelines The RVC system may have a guideline overlay that can help the driver align the vehicle when backing into a parking spot. To turn the guidelines on or off: 1. Shift into P (Park). 2. Press SETTINGS on the home

screen of the infotainment system.

3. Select Rear Camera. 4. Select Guidance Lines, then

select Off or On.

Driving and Operating

9-51

Rear Vision Camera Error Messages SERVICE REAR VISION CAMERA SYSTEM: This message can display on the infotainment screen when the system is not working properly. If any other problem occurs or if a problem persists, see your dealer. Rear Vision Camera Location The camera is under the tailgate handle. The area displayed by the camera is limited. It does not display objects that are close to either corner or under the bumper and can vary depending on vehicle orientation or road conditions. Displayed images may be further or closer than they appear. The following illustrations show the field of view that the camera provides.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (52,1)

9-52

Driving and Operating

When the System Does Not Seem to Work Properly The RVC system may not work properly or display a clear image if:

It is dark. The sun or the beam of headlamps are shining directly into the camera lens. Ice, snow, mud, or anything else builds up on the camera lens. Clean the lens, rinse it with water, and wipe it with a soft cloth. The back of the vehicle is in an accident. The position and mounting angle of the camera can change or the camera can be affected. Be sure to have the camera, its position, and mounting angle checked at your dealer.

Disconnecting the Rear Vision Camera (RVC) The RVC must be disconnected if the tailgate needs to be removed.

The RVC is disconnected by disconnecting the connector behind the rear license plate.

Lane Departure Warning (LDW) If equipped, LDW may help avoid crashes due to unintentional lane departures. It may provide an alert if the vehicle is crossing a lane marking without using a turn signal in that direction. LDW uses a camera sensor to detect the lane markings at speeds of 56 km/h (35 mph) or greater.

1. View displayed by the

camera.

1. View displayed by the

camera.

2. Corner of the rear bumper.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (53,1)

{ Warning

Warning (Continued)

The LDW system does not steer the vehicle. The LDW system may not:

. Provide enough time to avoid

a crash.

. Detect lane markings under

poor weather or visibility conditions. This can occur if the windshield or headlamps are blocked by dirt, snow, or ice; if they are not in proper condition; or if the sun shines directly into the camera.

. Detect road edges. . Detect lanes on winding or

hilly roads.

(Continued)

If LDW only detects lane markings on one side of the road, it will only warn you when departing the lane on the side where it has detected a lane marking. Always keep your attention on the road and maintain proper vehicle position within the lane, or vehicle damage, injury, or death could occur. Always keep the windshield, headlamps, and camera sensors clean and in good repair. Do not use LDW in bad weather conditions.

Driving and Operating

9-53

How the System Works The LDW camera sensor is on the windshield ahead of the rearview mirror. To turn LDW on and off, press @ on the center stack. The control indicator will light when LDW is on.

When LDW is on, @ is green if LDW is available to warn of a lane departure. If the vehicle crosses a detected lane marking without using the turn signal in that direction, @ changes to amber and flashes. Additionally, there will be three beeps on the right or left, depending on the lane departure direction.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (54,1)

9-54

Driving and Operating

Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. When driving in the U.S. and Canada, to help keep the engine clean and maintain optimum vehicle performance, we recommend using TOP TIER Detergent Gasolines. See www.toptiergas.com for a list of TOP TIER Detergent Gasolines.

When the System Does Not Seem to Work Properly The system may not detect lanes as well when there are: . Close vehicles ahead. . Sudden lighting changes, such

as when driving through tunnels.

. Banked roads. If the LDW system is not functioning properly when lane markings are clearly visible, cleaning the windshield may help. LDW alerts may occur due to tar marks, shadows, cracks in the road, temporary or construction lane markings, or other road imperfections. This is normal system operation; the vehicle does not need service. Turn LDW off if these conditions continue.

Use regular unleaded gasoline meeting ASTM specification D4814
with a posted octane rating of 87 or

higher. Do not use gasoline with an octane rating below 87, as it may cause engine damage and will lower fuel economy.

Use of Seasonal Fuels Use summer and winter fuels in the appropriate season. The fuels industry automatically modifies the fuel for the appropriate season. If fuel is left in the vehicle tank for long periods of time, driving or starting could be affected. Drive the vehicle until the fuel is at one-half tank or less, then refuel with the current seasonal fuel.

Prohibited Fuels Gasolines containing oxygenates such as ethers and ethanol, as well as reformulated gasolines, are available in some cities. If these gasolines comply with the previously described specification, then they are acceptable to use. However, E85 (85% ethanol) and other fuels containing more than 15% ethanol must be used only in FlexFuel vehicles.

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (55,1)

Driving and Operating

9-55

{ Caution

Do not use fuel containing methanol. It can corrode metal parts in the fuel system and also damage plastic and rubber parts. That damage would not be covered under the vehicle warranty.

Some gasolines, mainly high octane racing gasolines, can contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). Do not use gasolines and/or fuel additives with MMT as they can reduce spark plug life and affect emission control system performance. The malfunction indicator lamp may turn on. If this occurs, see your dealer for service.

California Fuel Requirements If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California Emissions Standards, the vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance might be affected. The malfunction indicator lamp could turn on and the vehicle may not pass a smog-check test. See Malfunction Indicator Lamp on page 5-13. If this occurs, return to your authorized dealer for diagnosis. If it is determined that the condition is caused by the type of fuel used, repairs may not be covered by the vehicle warranty.

Fuels in Foreign Countries If planning to drive in countries outside the U.S. or Canada, the proper fuel might be hard to find. Check regional auto club or fuel retail brand websites for availability in the country where driving. Never use leaded gasoline, fuel containing methanol, manganese, or any other fuel not recommended. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty.

Fuel Additives To keep fuel systems clean, TOP TIER Detergent Gasoline is recommended. See Fuel on page 9-54. If TOP TIER Detergent Gasoline is not available, one bottle of Fuel System Treatment PLUS added to the fuel tank at every engine oil change, can help. Fuel System Treatment PLUS is the only

Chevrolet Colorado Owner Manual 7586788) - 2015 - CRC - 8/22/14

(GMNA-Localizing-U.S./Canada-

Black plate (56,1)

9-56

Driving and Operating

gasoline additive recommended by General Motors. It is available at your dealer.