Download PDF Manual

working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.


If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message can also come on. See Vehicle Messages on page 5‑23 for more information.


Passenger Airbag Status Indicator If the vehicle has one of the passenger airbag status indicators pictured in the following illustrations, then the vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator is on the instrument panel. See Passenger Sensing System on page 3‑27 for important safety information. In addition, if the vehicle has a passenger sensing system for the right front passenger position, the label on the vehicle's sun visors refer to “ADVANCED AIRBAGS”.


United States


Canada and Mexico


When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger frontal airbag.


Chevrolet Colorado Owner Manual - 2012


Black plate (12,1)


5-12


Instruments and Controls


If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.


{ WARNING


If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑10 for more information, including important safety information.


Charging System Light


If it does not, have the vehicle serviced by your dealer. The light should go out once the engine starts. If it stays on, or comes on while driving, there could be a problem with the charging system. A charging system message in the Driver Information Center (DIC) can also appear. See Battery Voltage and Charging Messages on page 5‑23 for more information. This light could indicate that there are problems with a generator drive belt, or that there is an electrical problem. Have it checked right away. If the vehicle must be driven a short distance with the light on, turn off accessories, such as the radio and air conditioner.


This light comes on briefly when the ignition key is turned to START, but the engine is not running, as a check to show it is working.


Chevrolet Colorado Owner Manual - 2012


Black plate (13,1)


Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions are at acceptable levels, to produce a cleaner environment. This light comes on when the vehicle is placed in ON/RUN, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. See Ignition Positions on page 9‑26 for more information.


If the malfunction indicator lamp comes on and stays on while the engine is running, this indicates that there is an OBD II problem and service is required.


Instruments and Controls


5-13


Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the


vehicle warranty. This could also result in a failure to pass a required Emission Inspection/ Maintenance test. See Accessories and Modifications on page 10‑4. This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades.


If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.


Chevrolet Colorado Owner Manual - 2012


Black plate (14,1)


5-14


Instruments and Controls


If the light continues to flash, stop and park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emission system malfunction: . Check that the fuel cap is fully


installed. See Filling the Tank on page 9‑55. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off.


. Check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9‑53. If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed.


Emissions Inspection and Maintenance Programs Some local governments may have programs to inspect the on-vehicle emission control equipment. For the inspection, the emission system test equipment is connected to the vehicle’s Data Link Connector (DLC).


The DLC is under the instrument panel to the left of the steering wheel. See your dealer if assistance is needed.


Chevrolet Colorado Owner Manual - 2012


Black plate (15,1)


Instruments and Controls


5-15


The vehicle may not pass inspection if:


The malfunction indicator lamp is on with the engine running, or if the light does not come on when the ignition is turned to ON/RUN while the engine is off. See your dealer for assistance in verifying proper operation of the malfunction indicator lamp. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed. The vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving.


If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.


Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working If the warning light comes on, there could be a brake problem. Have the brake system inspected right away.


English


Metric


This light comes on briefly when the ignition key is turned to ON/RUN. If it does not, have it fixed so it will be ready to warn if there is a problem. When the ignition is on, the brake system warning light comes on when the parking brake is set. See Parking Brake on page 9‑45 for more information. The light stays on if the parking brake does not release fully. If it stays on after the parking brake is fully released, it means there is a brake problem.


Chevrolet Colorado Owner Manual - 2012


Black plate (16,1)


5-16


Instruments and Controls


If the light comes on while driving, pull off the road and stop. The brake pedal might be harder to push, or it might go closer to the floor. It can take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle on page 10‑91.


{ WARNING


The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.


Antilock Brake System (ABS) Warning Light


The Antilock Brake System (ABS) light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem.


If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. A chime may also sound when the light comes on steady. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5‑15. See Driver Information Center (DIC) on page 5‑20 for all brake related DIC messages.


Chevrolet Colorado Owner Manual - 2012


Black plate (17,1)


Instruments and Controls


5-17


StabiliTrak® OFF Light


Traction Control System (TCS)/StabiliTrak® Light


The StabiliTrak and Traction Control System (TCS) indicator/warning light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally the indicator light then goes off.


This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If the TCS is off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control System (TCS) on page 9‑47 and StabiliTrak® System on page 9‑48 for more information.


The light flashes while the StabiliTrak system and TCS are working to assist the driver with directional control of the vehicle in difficult driving conditions. If the StabiliTrak system and TCS light comes on and stays on while driving and a TRACTION FAULT or SERVICE STAB SYS message displays on the DIC, the vehicle needs service. See StabiliTrak® System on page 9‑48, Traction Control System (TCS) on page 9‑47 and Ride Control System Messages on page 5‑26 for more information.


Chevrolet Colorado Owner Manual - 2012


Black plate (18,1)


5-18


Instruments and Controls


Tire Pressure Light


For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.


When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated.


A Driver Information Center (DIC) tire pressure message may also display. See Vehicle Messages on page 5‑23 for more information. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑54 for more information.


When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10‑57 for more information.


Engine Oil Pressure Light


{ WARNING


Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.


Chevrolet Colorado Owner Manual - 2012


Black plate (19,1)


low can also damage the


Notice: Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil. This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then goes off. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and it might have some other system problem.


Instruments and Controls


5-19


Security Light


Cruise Control Light


For information regarding this light and the vehicle's security system, see Anti-theft Alarm System on page 2‑10.


High-Beam On Light


The cruise control light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 9‑50 for more information.


This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑2 for more information.


Chevrolet Colorado Owner Manual - 2012


Black plate (20,1)


5-20


Instruments and Controls


Information Displays


Driver Information Center (DIC) The Driver Information Center (DIC) displays information such as the trip odometer, personalization features, and warning messages. The DIC display is located on the instrument panel cluster. Operation and Displays The Driver Information Center (DIC) comes on when the ignition is on. If a problem is detected, a warning message appears on the display. Pressing and releasing the trip odometer reset stem on the DIC acknowledges some current warnings or service messages. Some messages only clear after the required action has been taken. The DIC has different menu items which can be accessed by pressing the trip odometer reset stem on the DIC. This includes trip information,


such as the odometer and trip odometer, engine oil life reset, and personalization features that are explained in the following information. The DIC trip odometer reset stem is located on the instrument panel cluster next to the DIC display. Trip Information


Odometer The odometer is automatically displayed on the DIC when you start the vehicle. The odometer shows the total distance the vehicle has been driven in either miles for the United States or kilometers for Canada.


Trip Odometer Press and release the reset stem until TRIP appears on the DIC display. The trip odometer shows the current distance traveled since the last reset of the trip odometer in either miles for the United States or kilometers for Canada.


To reset the trip odometer, press and hold the reset stem until the display returns to zero. Engine Oil Life System With the engine off, turn the key to ON/RUN and then press the reset stem until OIL LIFE RESET appears — alternating between OIL LIFE and RESET — on the DIC display. The CHANGE OIL message alerts you to change the oil on a schedule consistent with your driving conditions. Always reset the OIL LIFE message after an oil change. To reset the message, see Engine Oil Life System on page 10‑12. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Engine Oil on page 10‑10 and Maintenance Schedule on page 11‑3 for more information.


Chevrolet Colorado Owner Manual - 2012


Black plate (21,1)


Instruments and Controls


5-21


Personalization Features


Language This feature allows you to choose the language in which the DIC display shows information. To set your choice for this feature: 1. With the engine off, turn the key to ON/RUN, but do not start the engine.


2. Close all doors so the DOORS


message does not display in the DIC.


3. Momentarily press and release the reset stem until the current language is displayed: English (default), Spanish, or French. 4. To select a different language, press and hold the reset stem until the next language appears.


5. Repeat Step 4 until the desired


language is displayed. Once the desired language is shown on the DIC display, the language is set.


6. To exit the language selection, momentarily press and release the reset stem. All DIC messages will now display in the language selected.


Automatic Door Locks This feature allows you to program the door locks to a preferred setting. To set your choice for this feature: 1. With the engine off, turn the key


to LOCK/OFF. Do not remove the key from the ignition.


2. Press and hold the power door lock button until the DIC display shows the current door lock mode.


3. To view the next available mode,


press and hold the reset stem until the mode appears. Release the reset stem and press and hold again to view the next mode.


4. Once the desired mode is shown on the DIC display, briefly press the reset stem to set your choice. The DIC display then clears.


The following are the available modes: Lock 1 (default): On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of P (Park) and unlocks all of the doors when the vehicle is shifted into P (Park). On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 24 km/h (15 mph) and unlocks all of the doors when the key is removed from the ignition.


Chevrolet Colorado Owner Manual - 2012


Black plate (22,1)


5-22


Instruments and Controls


Lock 2: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of P (Park) and unlocks the driver's door when the vehicle is shifted into P (Park). On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 24 km/h (15 mph) and unlocks the driver's door when the key is removed from the ignition. Lock 3: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of P (Park). The doors will not automatically unlock. On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 24 km/h (15 mph). The doors will not automatically unlock.


Remote Keyless Entry (RKE) Feedback This feature allows you to program the Remote Keyless Entry (RKE) feedback to a preferred setting. To set your choice for this feature: 1. With the engine off, turn the key


to LOCK/OFF. Do not remove the key from the ignition.


2. Press and hold the lock and unlock buttons on the RKE transmitter at the same time. Hold both buttons until the DIC display shows the current RKE feedback mode.


3. To view the next available mode,


press and hold the reset stem until the mode appears. Release the reset stem and press and hold again to view the next mode.


4. Once the desired mode is shown on the DIC display, briefly press the reset stem to set your choice. The DIC display then clears.


The following are the available modes: RFA 1 (default): This mode flashes the parking lamps when you press the lock or unlock buttons on the RKE transmitter. RFA 2: This mode flashes the parking lamps and sounds the horn when you press the lock button on the RKE transmitter. This mode also flashes the parking lamps when you press the unlock button on the RKE transmitter. RFA 3: This mode flashes the parking lamps and sounds the horn when you press the lock or unlock buttons on the RKE transmitter. RFA 4: This mode disables RKE feedback. There will be no feedback when you press the lock or unlock buttons on the RKE transmitter.


Chevrolet Colorado Owner Manual - 2012


Black plate (23,1)


Instruments and Controls


5-23


Vehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. The messages are displayed for several seconds each. Some messages may not require immediate action, but you should press and release the trip odometer reset stem to acknowledge that you received the messages and to clear them from the display. Each message must be acknowledged individually. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the display seriously and remember that clearing the messages only makes the messages disappear, not correct the problem.


The following are the possible messages that can be displayed and some information about them.


Battery Voltage and Charging Messages


SERVICE CHARG (Charge) SYS (System) This message displays if there is a problem with the battery charging system. Under certain conditions, the battery warning light may also turn on in the instrument panel cluster. See Charging System Light on page 5‑12. The battery will not be charging at an optimal rate and the vehicle will lose the ability to enter the fuel economy mode. The vehicle is safe to drive, however have the electrical system checked by your dealer. Press and release the reset stem to acknowledge the message and clear it from the display.


Brake System Messages


ABS (Antilock Brake System) FAULT This message displays if there is a problem with the Antilock Brake System (ABS). Check the ABS as soon as possible and have your vehicle serviced by your dealer. See Braking on page 9‑4 and Antilock Brake System (ABS) Warning Light on page 5‑16 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. BRAKES This message displays if there is a problem with the brakes. Check the brakes as soon as possible and have your vehicle serviced by your dealer. See Braking on page 9‑4
and Antilock Brake System (ABS) Warning Light on page 5‑16 for more information. Press and release the reset stem to acknowledge the message and clear it from the display.


Chevrolet Colorado Owner Manual - 2012


Black plate (24,1)


5-24


Instruments and Controls


FLUID This message displays if the brake fluid is low. Check the brake fluid as soon as possible and have your vehicle serviced by your dealer. See Braking on page 9‑4 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. PARK BRK (Brake) This message displays when the parking brake is set. See Parking Brake on page 9‑45 and Antilock Brake System (ABS) Warning Light on page 5‑16 for more information. The message clears from the display after the parking brake is released or by pressing and releasing the reset stem.


Door Ajar Messages


DOORS This message displays when one or more of the doors is ajar. Check all the doors on your vehicle to make sure they are closed. The message clears from the display after all of the doors are closed.


Engine Cooling System Messages


AC (Air Conditioning) OFF This message displays when the engine coolant temperature is too high and the air conditioning in your vehicle needs to be turned off. See Engine Overheating on page 10‑23
and Climate Control Systems on page 8‑1 for more information. This message displays along with the ENG HOT message.


ENG (Engine) HOT This message displays when the engine coolant temperature is hot. Check the engine coolant temperature gauge. See Engine Coolant Temperature Gauge on page 5‑9. Have your vehicle serviced by your dealer as soon as possible if you suspect the engine is overheating. See Engine Overheating on page 10‑23 for more information.


Engine Oil Messages


CHANGE OIL This message displays when the oil needs to be changed. Check the oil in your vehicle as soon as possible and have your vehicle serviced by your dealer. See Engine Oil on page 10‑10 and Maintenance Schedule on page 11‑3 for more information. Press and release the reset stem to acknowledge the message and clear it from the display.


Chevrolet Colorado Owner Manual - 2012


Black plate (25,1)


Instruments and Controls


5-25


OIL This message displays when the oil pressure is low. See Engine Oil Pressure Light on page 5‑18 and Engine Oil on page 10‑10 for more information.


Engine Power Messages


REDUCED POWER This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible. Press and release


the reset stem to acknowledge the message and clear it from the display.


Fuel System Messages


FUEL CAP This message displays if the vehicle's fuel cap is either off or loose. Pull over as soon as possible and check to see if the fuel cap is secure. You may also see the check engine light on the instrument panel cluster. If the check engine light does come on when the fuel cap was loose, it may take a few driving trips before the light turns off. See Malfunction Indicator Lamp on page 5‑13 for more information if the light still remains on. Press and release the reset stem to acknowledge the message and clear it from the display.


LOW FUEL This message displays if the level of fuel in the vehicle is low. Also check the fuel gauge. See Fuel Gauge on page 5‑8 for more information. Refill the fuel tank as soon as possible.


Lamp Messages


TURN SIGNAL This message displays when the turn signal is on for about 1.2 km (0.75 miles) of travel. Press and release the reset stem to acknowledge the message and clear it from the display.


Chevrolet Colorado Owner Manual - 2012


Black plate (26,1)


5-26


Instruments and Controls


Ride Control System Messages


SERVICE STAB (Stability) SYS (System) This message displays if there is a problem with the StabiliTrak system. Have your vehicle serviced by your dealer. See StabiliTrak® System on page 9‑48 for more information. STAB (Stability) SYS (System) OFF This message displays when the StabiliTrak system is turned off. See StabiliTrak® System on page 9‑48
for more information.


TRAC (Traction) OFF This message displays when the Traction Control System (TCS) is turned off by pressing the StabiliTrak button. See StabiliTrak® System on page 9‑48 for more information. TRAC (Traction) ON This message displays when the Traction Control System (TCS) is turned on when it was previously off during the same ignition cycle. TRAC (Traction) LOW This message displays when the Traction Control System (TCS) is active.


TRACTION FAULT This message will display if there is a problem with the TCS. Have your vehicle serviced by your dealer. See StabiliTrak® System on page 9‑48
for more information. Press and release the reset stem to acknowledge the message and clear it from the display.


Service Vehicle Messages


SERV (Service) VEH (Vehicle) This message displays if your vehicle needs service. Have your vehicle serviced by your dealer as soon as possible.


Chevrolet Colorado Owner Manual - 2012


Black plate (27,1)


Instruments and Controls


5-27


Tire Messages


LOW TIRE This message displays if a low tire pressure is detected in any of the vehicle's tires. Press and release the reset stem to acknowledge the message and clear it from the display. The message appears at each ignition cycle until the tires are inflated to the correct inflation pressure. See Tires on page 10‑47
and Tire Pressure on page 10‑54 for more information on tires and the correct inflation pressures.


SERV (Service) TPM (Tire Pressure Monitor) This message displays if a part on the Tire Pressure Monitor System (TPMS) is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 5‑18. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 10‑57 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer.


Transmission Messages


SERV (Service) 4WD (Four-Wheel Drive) This message displays when there is a problem with the transfer case control system. Check the transfer case on your vehicle and have it serviced by your dealer. See Four-Wheel Drive on page 9‑40 for more information about the transfer case. Press and release the reset stem to acknowledge the message and clear it from the display.


Chevrolet Colorado Owner Manual - 2012


Black plate (28,1)


5-28


Instruments and Controls


2 NOTES


Chevrolet Colorado Owner Manual - 2012


Black plate (1,1)


Lighting


Exterior Lighting


Exterior Lighting


Exterior Lamp Controls


Exterior Lamp Controls . . . . . . . . 6-1
Exterior Lamps Off


Reminder . . . . . . . . . . . . . . . . . . . . 6-2


Headlamp High/Low-Beam


Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running


Lamps (DRL) . . . . . . . . . . . . . . . . 6-3


Automatic Headlamp


System . . . . . . . . . . . . . . . . . . . . . . 6-3
Hazard Warning Flashers . . . . . 6-4
Turn and Lane-Change


Signals . . . . . . . . . . . . . . . . . . . . . . 6-4
Fog Lamps . . . . . . . . . . . . . . . . . . . . 6-5
Exterior Cargo Lamps . . . . . . . . . 6-5


Interior Lighting


Instrument Panel Illumination


Control . . . . . . . . . . . . . . . . . . . . . . 6-6
Dome Lamps . . . . . . . . . . . . . . . . . 6-6


Lighting Features


Exit Lighting . . . . . . . . . . . . . . . . . . . 6-7
Battery Load Management . . . . 6-7
Battery Power Protection . . . . . . 6-7


The exterior lamp control is located on the instrument panel on the left side of the steering wheel. O (Exterior Lamps): Turn the knob, located to the right of this symbol, to choose one of the four exterior lamp positions. O (Off): Turns off all exterior lamps including the Daytime Running Lamps (DRL).


Lighting


6-1


AUTO: Turns the headlamps on automatically at normal brightness, together with the following: . Sidemarker Lamps


Taillamps


. Parking Lamps


Instrument Panel Lights


See Automatic Headlamp System on page 6‑3 for more information. ; (Parking Lamps): Turns on the parking lamps, together with the following: . Sidemarker Lamps


Taillamps License Plate Lamps Instrument Panel Lights


2 (Headlamps): Turns on the headlamps, together with the previously listed lamps and lights.


Chevrolet Colorado Owner Manual - 2012


Black plate (2,1)


6-2


Lighting


Exterior Lamps Off Reminder If a door is open, a reminder chime sounds when the headlamps or parking lamps are manually turned on and the key is out of the ignition. To turn off the chime, turn the headlamp switch to off and then back on. In the automatic mode, the headlamps turn off once the ignition is in LOCK/OFF. For vehicles first sold in Canada, if the parking lamps are turned on manually, the Daytime Running Lamps (DRL) will stay on.


Headlamp High/ Low-Beam Changer 2 3 Headlamp High/Low Beam Changer: Push the turn signal/ multifunction lever away from you to turn the high beams on. Pull the lever towards you to return to low beams.


This indicator light turns on in the instrument panel cluster when the high beam headlamps are on.


Flash-to-Pass This feature lets you use the high-beam headlamps to signal a driver in front of you that you want to pass. It works even if the headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If the headlamps are in the automatic position or on low beam, the high-beam headlamps will turn on. They will stay on as long as the lever is held toward you. The high-beam indicator on the instrument panel cluster will come on. Release the lever to return to normal operation.


Chevrolet Colorado Owner Manual - 2012


Black plate (3,1)


When it begins to get dark, the headlamps will automatically switch from DRL to the regular headlamps. The regular headlamp system should be turned on when needed.


Automatic Headlamp System When it is dark enough outside, the automatic headlamp system will turn on after the transmission has been shifted from P (Park) to D (Drive). The headlamps, taillamps, sidemarker, parking lamps, roof marker lamps, and the instrument panel lights turn on at normal brightness. The radio lights will become dimmer when the headlights are off compared to when the headlights are on.


Lighting


6-3


The vehicle has a light sensor located on the top of the instrument panel. Do not cover the sensor, or the system will be on whenever the ignition is on. The system can turn on the headlamps when driving in a parking garage, through a tunnel or when there is overcast weather. This is normal. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp system so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor detects a change in lighting lasting longer than the delay.


Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system will come on when the following conditions are met:


The ignition is on. The exterior lamps control is in AUTO. The transmission is not in P (Park) if you have an automatic transmission. The light sensor determines it is daytime.


When the DRL are on, only the parking lamps or reduced intensity low beam headlamps will be on. The taillamps, sidemarkers, and other lamps will not be on. The instrument panel will not be lit up either.


Chevrolet Colorado Owner Manual - 2012


Black plate (4,1)


6-4


Lighting


If the vehicle is started in a dark garage, the automatic headlamp system will come on immediately. Once the vehicle leaves the garage, it will take about 1 minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, the instrument panel cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Illumination Control on page 6‑6.


Hazard Warning Flashers


Turn and Lane-Change Signals


| (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press | again to turn the flashers off. The turn signals do not work while the hazard warning flashers are on.


Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is complete. The lever returns to its starting position when it is released.


Chevrolet Colorado Owner Manual - 2012


Black plate (5,1)


If after signaling a turn or a lane change the arrows flash rapidly or do not come on, a signal bulb may be burned out. Replace any burned out bulbs. If a bulb is not burned out, check the fuse. For bulb replacement, see Taillamps, Turn Signal, Stoplamps, and Back-Up Lamps on page 10‑37. For a blown fuse or circuit breaker, see Fuses and Circuit Breakers on page 10‑40.


Turn Signal On Chime If a turn signal is left on for more than 1.2 km (3/4 of a mile), a chime will sound at each flash of the turn signal and the message TURN SIGNAL will also appear in the DIC. To turn the chime and message off, move the turn signal lever to the off position. See “TURN SIGNAL” under Lamp Messages on page 5‑25 for more information.


Fog Lamps


The fog lamp button is located near the exterior lamps control. # (Fog Lamps): For vehicles with fog lamps, press to turn the fog lamps on or off. An indicator light will turn on in the button when the fog lamps are on. The parking lamps or low-beam headlamps must be on for the fog lamps to work. The fog lamps will go off whenever the high-beam headlamps come on. When the high beams go off, the fog lamps come on again.


Lighting


6-5


Some localities have laws that require the headlamps to be on along with the fog lamps.


Exterior Cargo Lamps The cargo lamps (if equipped) can be used if more light is needed in the cargo area of the vehicle or in the top-box storage units.


This button is located on the driver side of the instrument panel near the exterior lamp control.


Chevrolet Colorado Owner Manual - 2012


Black plate (6,1)


6-6


Lighting


Press to turn the cargo lamps on and off. The dome lamps must be on for the cargo lamps to come on. See Dome Lamps on page 6‑6. If the vehicle is equipped with Bluetooth®, turning the instrument panel illumination control thumbwheel all the way up will turn on the cargo lamps.


Interior Lighting


Instrument Panel Illumination Control D (Instrument Panel Lights): Turn the thumbwheel up or down to brighten or dim the instrument panel lights and the radio display. The instrument panel lights, cluster, and radio display do not dim to complete darkness. Turning the thumbwheel all the way up will turn on the dome lamps and may also turn on the cargo lamp, if the vehicle is equipped with Bluetooth. The instrument panel light brightness control will only work if the headlamps or parking lamps are on. See Exterior Lamp Controls on page 6‑1.


Dome Lamps The dome lamps come on when any door is opened.


To manually turn on the dome lamps, turn the thumbwheel, located next to the exterior lamps control, all the way up. The cargo lamps may come on, if the vehicle is equipped with Bluetooth. In this position, the lamps remain on whether a door is opened or closed.


Reading Lamps Press the lens on the lamps to turn each reading lamp on or off. These lamps will not come on with the dome lamps.


Dome Lamp Override The dome lamp override button is located below the exterior lamps control. E (Dome Lamp Override): Press this button in to make the dome lamps remain off when the doors are open. To return the lamps to automatic operation, press E again and return it to the out position.


Chevrolet Colorado Owner Manual - 2012


Black plate (7,1)


Lighting Features


Exit Lighting The interior lamps will come on when the key is removed from the ignition. The lamps will not come on if the dome override button is pressed in.


Battery Load Management The vehicle has Electric Power Management (EPM) that estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery's state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gauge or a voltage display on the Driver Information Center (DIC), you may see the


voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all of the power needed for very high electrical loads. A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator's output and the vehicle's electrical needs. It can increase engine idle speed to generate more power whenever


Lighting


6-7


needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a DIC message might be displayed, such as BATTERY SAVER ACTIVE, BATTERY VOLTAGE LOW, or LOW BATTERY. If one of these messages displays, it is recommended that the driver reduce the electrical loads as much as possible. See Driver Information Center (DIC) on page 5‑20.


Battery Power Protection This feature shuts off the dome lamp if it is left on for more than 20 minutes when the ignition is in LOCK/OFF. This helps to prevent the battery from running down.


Chevrolet Colorado Owner Manual - 2012


Black plate (8,1)


6-8


Lighting


2 NOTES


Chevrolet Colorado Owner Manual - 2012


Black plate (1,1)


Introduction


Infotainment Determine which radio the vehicle has and read the following pages to become familiar with its features.


Infotainment System 7-1


{ WARNING


Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to infotainment tasks while driving.


This system provides access to many audio and non audio listings.


Infotainment System


Introduction


Infotainment . . . . . . . . . . . . . . . . . . . 7-1
Theft-Deterrent Feature . . . . . . . 7-2
Operation . . . . . . . . . . . . . . . . . . . . . 7-3


Radio


AM-FM Radio . . . . . . . . . . . . . . . . . 7-7
Satellite Radio . . . . . . . . . . . . . . . 7-11
Radio Reception . . . . . . . . . . . . . 7-13
Fixed Mast Antenna . . . . . . . . . 7-14
Satellite Radio Antenna . . . . . . 7-14


Audio Players


CD Player . . . . . . . . . . . . . . . . . . . 7-15


Phone


Bluetooth . . . . . . . . . . . . . . . . . . . . 7-21


Chevrolet Colorado Owner Manual - 2012


Black plate (2,1)


7-2


Infotainment System


To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: . Become familiar with the


operation and controls of the audio system.


. Set up the tone, speaker


adjustments, and preset radio stations.


For more information, see Defensive Driving on page 9‑3. Notice: Contact your dealer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment.


Notice: The chime signals related to safety belts, parking brake, and other functions of the vehicle operate through the radio/ entertainment system. If that equipment is replaced or additional equipment is added to the vehicle, the chimes may not work. Make sure that replacement or additional equipment is compatible with the vehicle before installing it. See Accessories and Modifications on page 10‑4. The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 9‑31 for more information.


Theft-Deterrent Feature TheftLock® is designed to discourage theft of the radio. The feature works automatically by learning a portion of the Vehicle Identification Number (VIN). If the radio is moved to a different vehicle, it does not operate and either LOC or LOCKED displays. When the radio and vehicle are turned off, there may be a blinking red light to indicate TheftLock is armed. With TheftLock activated, the radio does not operate if stolen.


Chevrolet Colorado Owner Manual - 2012


Black plate (3,1)


Operation


Infotainment System 7-3


AM-FM Radio


Chevrolet Colorado Owner Manual - 2012


Black plate (4,1)


7-4


Infotainment System


q VOL r (Volume): Turn to increase or to decrease the volume. DISPL (Display): When the ignition is turned off, press to display the time. For RDS, press the DISPL knob to change what displays while using RDS. The display options are station name, RDS station frequency, PTY (program type), and the name of the program (if available). For XM™ (if equipped), press the DISPL knob while in XM mode to retrieve four different categories of information related to the current song or channel: Artist, Song Title, Category or PTY, Channel Number/ Channel Name. To change the default on the display, press the DISPL knob until you see the desired display, then press and hold this knob for two seconds and the radio beeps once.


Radio with CD (MP3/WMA)


Playing the Radio


AM-FM Radio PWR (Power): Press to turn the system on and off. VOL (Volume): Turn to increase or to decrease the volume.


RCL (Recall): Press to switch the display between the radio station frequency, band, and the time. When the ignition is off, press to display the time.


Radio with CD (MP3/WMA) PWR (Power): Press to turn the system on and off.


Chevrolet Colorado Owner Manual - 2012


Black plate (5,1)


AUTO VOL (Automatic Volume): Automatic volume automatically adjusts the audio system to make up for road and wind noise while driving. The volume level should always sound the same while driving. Set the volume at the desired level. Press to select LOW, MEDIUM, and HIGH. AVOL displays. Each higher setting allows for higher volume compensation at faster vehicle speeds. NONE displays if the radio cannot determine the vehicle speed. To turn automatic volume off, press until OFF displays. Setting the Tone (Bass/Treble)


AM-FM Radio To adjust the bass or treble: 1. Press and release the AUDIO button until BAS (bass) or TRE (treble) displays.


2. Press and hold the w or x button to increase or to decrease the tone.


To adjust the bass or treble to the center position: 1. Press and release the AUDIO button until BAS (bass) or TRE (treble) displays.


2. Press and hold the AUDIO


button for more than two seconds until a beep sounds.


To adjust both tone controls and both speaker controls to the middle position: 1. Exit out of audio mode by


pressing another button, causing the radio to perform that function or wait five seconds for the display to return to time of day. 2. Press and hold AUDIO for more


than two seconds until a beep sounds. CEN (center) displays.


Infotainment System 7-5


Radio with CD (MP3/WMA) To adjust the bass or treble: 1. Press and release the AUDIO


knob until BASS (bass) or TREB (treble) displays.


2. Turn the AUDIO knob to increase or to decrease the tone.


To adjust the bass/treble to the middle position, press and hold the AUDIO knob. The radio produces one beep and adjusts the display level to the middle position. To adjust all tone and speaker controls to the middle position, push and hold the AUDIO knob when no tone or speaker control displays. ALL CENTERED displays and a beep sounds.


Chevrolet Colorado Owner Manual - 2012


Black plate (6,1)


7-6


Infotainment System


AUTO EQ (Automatic Equalization): Press to select customized equalization settings designed for country/western, jazz, talk, pop, rock, and classical. To return to the manual mode, press the AUTO EQ button until CUSTOM displays. Then manually adjust the bass/treble, using the AUDIO knob. Adjusting the Speakers (Balance/Fade) Fade may not be available if the vehicle is a regular cab model.


AM-FM Radio To adjust balance or fade: 1. Press and release the AUDIO button until BAL (balance) or FAD (fade) displays.


2. Press and hold the w or x button to increase or to decrease the level.


To adjust the balance or fade to the center position: 1. Press and release the


AUDIO button until BAL (balance) or FAD (fade) displays.


2. Press and hold the


AUDIO button for more than two seconds until a beep sounds.


To adjust both speaker controls and both tone controls to the middle position: 1. Exit out of audio mode by


pressing another button, causing the radio to perform that function or wait five seconds for the display to return to time of day. 2. Press and hold AUDIO for more


than two seconds until a beep sounds. CEN (center) displays.


Radio with CD (MP3/WMA) To adjust the balance or fade: 1. Press and release the


AUDIO knob until BAL (balance) or FADE (fade) displays. 2. Turn the AUDIO knob to


increase or to decrease the level.


To adjust the balance or fade to the middle position: 1. Press and release the


AUDIO knob until BAL (balance) or FADE (fade) displays.


2. Press and hold the AUDIO knob


until one beep sounds.


To adjust all tone and speaker controls to the middle position, push and hold the AUDIO knob when no tone or speaker control displays. ALL CENTERED displays and a beep sounds.


Chevrolet Colorado Owner Manual - 2012


Black plate (7,1)


Radio Messages


AM-FM Radio CAL (Calibration Error): The audio system has been calibrated for the vehicle from the factory. If CAL displays it means that the radio has not been configured properly for the vehicle and it must be returned to your dealer for service. LOC (Locked): This message displays when the THEFTLOCK® system has locked up. Take the vehicle to your dealer for service. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer.


Radio with CD (MP3/WMA) CAL ERR (Calibration Error): The audio system has been calibrated for the vehicle from the factory. If CAL ERR displays it means that the radio has not been configured properly for the vehicle and it must be returned to your dealer for service. LOCKED: This message displays when the TheftLock® system has locked up. Take the vehicle to your dealer for service. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer.


Infotainment System 7-7


Radio


AM-FM Radio


Finding a Station


AM-FM Radio AM FM: Press to switch between FM1, FM2, or AM. TUNE: Turn to select radio stations. o SEEK: Press to go to the previous station and stay there. To scan stations, press and hold o SEEK for two seconds until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press o SEEK again to stop scanning.


Chevrolet Colorado Owner Manual - 2012


Black plate (8,1)


7-8


Infotainment System


To scan preset stations, press and hold o SEEK for more than four seconds until two beeps sound. The radio goes to the first preset station, plays for a few seconds, then goes to the next preset station. Press o SEEK again to stop scanning presets. SEEK p : Press to go to the next station and stay there. To scan stations, press and hold SEEK p for two seconds until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press SEEK p again to stop scanning. To scan preset stations, press and hold SEEK p for more than four seconds until two beeps sound. The radio goes to the first preset station stored on the pushbuttons, plays for a few seconds, then goes to the next preset station. Press SEEK p again to stop scanning presets.


Radio with CD (MP3/WMA) BAND: Press to switch between FM1, FM2, AM, or XM1 or XM2
(if equipped). The selection displays. q TUNE r : Turn to select radio stations. q SEEK r : Press to go to the previous or next station and stay there. q SCAN r : Press and hold for more than two seconds, SCAN displays and the radio beeps once. The radio goes to a station, plays for a few seconds, then goes to the next station. Press q or r again, to stop scanning presets. To scan preset stations, press and hold q or r for more than four seconds, PSCN displays and the radio beeps once. The radio goes to a preset station, plays for a few seconds, then goes to the next preset station. Press q or r again, to stop scanning presets.


Radio Data System (RDS) The Radio with CD (MP3/WMA) has an RDS system. RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: . Seek to stations broadcasting


the selected type of programming.


. Receive announcements


concerning local and national emergencies.


. Display messages from radio


stations.


. Seek to stations with traffic


announcements.


Chevrolet Colorado Owner Manual - 2012


Black plate (9,1)


This system relies upon receiving specific information from these stations and only works when the information is available. In rare cases, a radio station could broadcast incorrect information that causes the radio features to work improperly. If this happens, contact the radio station. While the radio is tuned to an RDS station, the station name or call letters display instead of the frequency. RDS stations can also provide the time of day, a program type (PTY) for current programming, and the name of the program being broadcast.


RDS Messages ALERT!: The Alert feature warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! displays. The announcement is heard, even if the volume is low or a CD is playing. If a CD is playing, play stops during the


If the current


announcement. Alert announcements cannot be turned off. ALERT! is not affected by tests of the emergency broadcast system. This feature is not supported by all RDS stations. INFO (Information): station has a message, the information symbol or INFO displays. Press this button to see the message. The message can display the artist, song title, call in phone numbers, etc. If the entire message is not displayed, parts of the message display every three seconds. To scroll through the message, press and release the INFO button. A new group of words displays after every press of this button. Once the complete message has displayed, the information symbol or INFO disappears from the display until another new message is received.


Infotainment System 7-9


The last message can be displayed by pressing the INFO button. The last message stays on the display until a new message is received or the radio is tuned to a different station. When a message is not available from a station, NO INFO displays. TRAF (Traffic): TRAF displays when the station tuned to broadcasts traffic announcements. When a traffic announcement is broadcast on this station you will hear it. If the station does not broadcast traffic announcements, press the TRAF button and the radio seeks to a station that does. When a station that broadcasts traffic announcements is found, the radio stops seeking and TRAF displays. If no station is found that broadcasts traffic announcements, NO TRAF displays.


Chevrolet Colorado Owner Manual - 2012


Black plate (10,1)


7-10


Infotainment System


If TRAF displays, press the TRAF button to turn off the traffic announcements. The radio plays the traffic announcement if the volume is low. The radio interrupts the play of a CD if the last tuned station broadcasts traffic announcements.


Finding a Program Type (PTY) Station To select and find a PTY station: 1. Turn the P-TYPE knob. TYPE


and a PTY displays.


2. Turn the P-TYPE knob again, to


select a PTY.


3. Once the desired PTY displays, press the SEEK / TYPE button to select PTY's first station.


4. To go to another station


within that PTY, press the SEEK / TYPE button twice to display the PTY and then go to another station.


To cancel the seek, press the SEEK / TYPE button. This also exits the program type seek mode and returns to the last tuned station. If both PTY and TRAF (traffic) are on, the radio searches for stations with the selected PTY and traffic announcements. If the radio cannot find the desired program type, NONE displays and the radio returns to the last tuned station. SCAN: To scan PTYs, press and hold the SEEK / SCAN until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. BAND (Alternate Frequency): Alternate frequency lets the radio switch to a stronger station with the same program type. To turn alternate frequency on, press and hold BAND for two seconds. AF ON displays. The radio could switch to stations with a stronger frequency.


To turn alternate frequency off, press and hold BAND again for 2 seconds. AF OFF displays. The radio does not switch to other stations. DISPL (Display): Press to change what information displays while using RDS. The display options are station name, RDS station frequency, PTY (program type), and the name of the program (if available).


Setting Preset PTYs Only The six pushbuttons have factory PTY presets. Up to 12 PTYs (six FM1 and six FM2), can be programmed on the numbered pushbuttons. To program PTYs: 1. Press BAND to select FM1


or FM2.


2. Turn the P‐TYPE knob to


activate program type select mode. TYPE and the last selected PTY displays.


Chevrolet Colorado Owner Manual - 2012


Black plate (11,1)


3. Turn the P‐TYPE knob to select


a PTY.


4. Press and hold one of the six numbered pushbuttons until a beep sounds. When that numbered pushbutton is pressed, the PTY that was set, returns.


5. Repeat the steps for each


pushbutton.


Setting Preset Stations If the radio does not have XM, up to 18 stations (six FM1, six FM2, and six AM) can be programmed on the six numbered pushbuttons. If the radio has XM, up to 30 stations (six FM1, six FM2, six AM, six XM1, and six XM2) can be programmed on the six numbered pushbuttons.


To program either radio: 1. Tune in the desired station. 2. Press and hold one of the six


numbered pushbuttons until the radio beeps once. When that numbered pushbutton is pressed again, the station that was stored, returns.


3. Repeat the steps for each


pushbutton.


Satellite Radio


XM™ Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. A service fee is required to receive the XM service. If XM Service needs to be reactivated, the radio will display "No Subscription Please Renew" on channel XM1.


Infotainment System 7-11


For more information, contact XM at www.xmradio.com or call 1-800-929-2100 in the U.S. and www.xmradio.ca or call 1-877-438-9677 in Canada. Finding a Program Type (PTY) Channel To select and find a PTY: 1. Turn the P-TYPE knob. TYPE


and a PTY displays.


2. Turn the P-TYPE knob again, to


Loading...
x