2015 Chevrolet Camaro Owners Manual

{ Caution

If improper coolant mixture, inhibitors, or additives are used in the vehicle cooling system, the engine could overheat and be damaged. Too much water in the

(Continued)

Caution (Continued)

mixture can freeze and crack engine cooling parts. The repairs would not be covered by the vehicle warranty. Use only the proper mixture of engine coolant for the cooling system. See Recommended Fluids and Lubricants on page 11-12.

Never dispose of engine coolant by putting it in the trash, pouring it on the ground, or into sewers, streams, or bodies of water. Have the coolant changed by an authorized service center, familiar with legal requirements regarding used coolant disposal. This will help protect the environment and your health. Checking Coolant The vehicle must be on a level surface when checking the coolant level.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (32,1)

10-32

Vehicle Care

How to Add Coolant to the Coolant Recovery Bottle

{ Warning

You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.

{ Caution

This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged.

Add coolant as follows: 1. Turn the engine coolant recovery

bottle dipstick cap counterclockwise and slowly pull out the dipstick.

2. Pour the coolant into the engine

coolant recovery bottle.

3. When the level is correct,

replace the dipstick and turn the cap clockwise to secure.

How to Add Coolant to the Radiator

{ Warning

You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.

{ Caution

This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged.

4. There are maximum and

minimum markings on the dipstick. When the engine is cold, the coolant level should be at or above the MIN mark on the dipstick. After the vehicle has been driven and the engine is at normal operating temperature, the level should be somewhere between half full and the maximum mark. If the coolant level is correct, replace the dipstick and turn the cap clockwise to secure.

5.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (33,1)

{ Warning

An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.

{ Warning

Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the surge tank pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the surge tank pressure cap, is hot. Wait for the cooling system and surge tank pressure cap to cool if you ever have to turn the pressure cap.

If coolant is needed, add the proper mixture directly to the radiator, but be sure the cooling system is cool before this is done. If no coolant is visible in the engine coolant recovery bottle, add coolant as follows:

3.6L V6 Engine Fill Procedure 1. Locate the radiator cap. See

Engine Compartment Overview on page 10-6.

2. Remove the engine cover to access the radiator cap. See Engine Cover on page 10-13.

3. Cover the radiator cap with a

thick cloth and turn it slowly counterclockwise and remove.

Vehicle Care

10-33

4.

If there is no coolant visible or the level is low, slowly fill the system through the radiator cap opening with a 50/50 mixture of DEX-COOL and clean drinkable water. Wait 30 seconds for coolant to settle and continue filling if the level drops. Do not spill coolant on the accessory drive belts. If a spill occurs, rinse the belt with fresh water. 5. Start the engine. 6. With the engine idling, continue

to add coolant through the radiator cap opening until full. Wait 30 seconds for the coolant to settle and top off, if the level drops.

7. Once the system is full, put the radiator cap back on by turning clockwise.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (34,1)

10-34

Vehicle Care

8. With the engine still running,

raise the engine to 2500 rpm for 30–40 seconds.

9. Turn the engine off. 10. Repeat Steps 2–7 then turn the

engine off.

11. Allow engine to cool for

45 minutes. Top off coolant through the radiator cap opening and reinstall the radiator cap.

12. Reinstall the engine cover. See

Engine Cover on page 10-13.

13. Check the coolant level in the engine coolant recovery bottle and fill it until the level is at the top symbol on the dipstick.

6.2L V8 and 7.0L V8 Engine Fill Procedure 1. Locate the radiator cap. See

Engine Compartment Overview on page 10-6.

2. Cover the radiator cap with a

thick cloth and turn it slowly counterclockwise and remove.

3.

If there is no coolant visible or the level is low, slowly fill the system through the radiator cap opening with a 50/50 mixture of clean, drinkable water and DEX-COOL coolant until full. Wait 30 seconds for coolant to settle and top off if the level drops. Do not spill coolant on the accessory drive belts. If a spill occurs, rinse the belt with fresh water. 4. Start the engine. 5. With the engine idling, top off the coolant through the radiator cap opening until full. Wait 30 seconds for the coolant to settle and top off, if the level drops.

6. Once the system is full, put the radiator cap back on by turning clockwise.

7. Turn the engine off.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (35,1)

Engine Overheating The vehicle has an indicator to warn of engine overheating. There is an engine coolant temperature gauge on the vehicle instrument panel. See Engine Coolant Temperature Gauge on page 5-12. If the decision is made not to lift the hood when this warning appears, but instead get service help right away. See Roadside Assistance Program on page 13-5. If the decision is made to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced.

Vehicle Care

10-35

{ Caution

Running the engine without coolant may cause damage or a fire. Vehicle damage would not be covered by the vehicle warranty.

If Steam Is Coming from the Engine Compartment { Warning

Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.

(Continued)

8. Check the coolant level in the engine coolant recovery bottle and fill it until the level is at the top mark on the dipstick.

{ Caution

If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (36,1)

10-36

Vehicle Care

Warning (Continued)

If you keep driving when the engine is overheated, the liquids in it can catch fire. You or others could be badly burned. Stop the engine if it overheats, and get out of the vehicle until the engine is cool.

If No Steam Is Coming from the Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: . Climbs a long hill on a hot day. . Stops after high-speed driving. Idles for long periods in traffic. Tows a trailer.

If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest

temperature and to the highest fan speed. Open the windows as necessary.

3. When it is safe to do so, pull off

the road, shift to P (Park) or N (Neutral) and let the engine idle.

If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slowly for about 10 minutes. Keep a safe vehicle distance from the vehicle in front. If the warning does not come back on, continue to drive normally and have the cooling system checked for proper fill and function. If the warning continues, pull over, stop, and park the vehicle right away.

If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down.

Power Steering Fluid (L99, LS3, ZL1 and Z/28) The vehicle has electric power steering and does not use power steering fluid.

Power Steering Fluid (LFX)

The power steering fluid reservoir is under the engine cover on the driver side toward the front of the engine compartment. See Engine Compartment Overview on page 10-6.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (37,1)

When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or an unusual noise is heard. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. How to Check Power Steering Fluid Check the level after the vehicle has been driven for at least 20 minutes so the fluid is warm. To check the power steering fluid: 1. Turn the ignition key to LOCK/

OFF and let the engine compartment cool down.

2. Remove the engine cover. See

Engine Cover on page 10-13.

3. Wipe the cap and the top of the

reservoir clean.

4. Turn the cap counterclockwise

and pull it straight up.

5. Wipe the dipstick with a

clean rag.

6. Replace the cap and completely

tighten it.

7. Remove the cap again and look at the fluid level on the dipstick.

When the engine is hot, the level should be at the hot MAX level. When the engine is cold, the fluid level should be between MIN and MAX on the dipstick.

What to Use To determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 11-12. Always use the proper fluid.

Vehicle Care

10-37

Washer Fluid

What to Use When windshield washer fluid is needed, be sure to read the manufacturer's instructions before use. If operating the vehicle in an area where the temperature can fall below freezing, use a fluid that has sufficient protection against freezing. Adding Washer Fluid

Open the cap with the washer symbol on it. Add washer fluid until the reservoir is full. See Engine Compartment Overview on page 10-6 for reservoir location.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (38,1)

10-38

Vehicle Care

{ Caution

. Do not use engine coolant

(antifreeze) in the windshield washer. It can damage the windshield washer system and paint.

. Do not mix water with

ready-to-use washer fluid. Water can cause the solution to freeze and damage the washer fluid tank and other parts of the washer system.

. When using concentrated

washer fluid, follow the manufacturer instructions for adding water.

. Fill the washer fluid tank only

three-quarters full when it is very cold. This allows for fluid expansion if freezing occurs, which could damage the tank if it is completely full.

Brakes Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time when the vehicle is moving, except when applying the brake pedal firmly.

{ Warning

The brake wear warning sound means that soon the brakes will not work well. That could lead to a crash. When the brake wear warning sound is heard, have the vehicle serviced.

{ Caution

Continuing to drive with worn-out brake pads could result in costly brake repair.

Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with the brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications. See Capacities and Specifications on page 12-2. Brake pads should be replaced as complete sets. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service may be required. Replacing Brake System Parts Always replace brake system parts with new, approved replacement parts. If this is not done, the brakes may not work properly. The braking

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (39,1)

performance expected can change in many other ways if the wrong replacement brake parts are installed or parts are improperly installed. Z/28 Brake Pad and Rotor Wear The Z/28 has electronic brake pad wear sensors. When the pads are worn, a message displays in the Driver Information Center. See Brake System Messages on page 5-33.

Visual Inspection Periodic visual inspection of the brake pads is required to determine when to replace the brake pads. . Brake pads can be visually

inspected through the wheel by inspecting the outer brake pads at each wheel.

. Brake pads should be replaced

when the pad lining is worn to 2 mm of pad thickness. New pads are 10 mm thick.

In addition, brake pad inspection is required any time the tires are removed.

The Z/28 has ceramic brake rotors. Rotors should be visually inspected when the brake pads are replaced. The rotor can be reused if it is within specification. Rotor inspection and measuring methods can be found in the service manual. See Service Publications Ordering Information on page 13-11.

Brake Fluid

The brake/clutch master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. See Engine Compartment Overview on page 10-6 for the location of the reservoir.

Vehicle Care

10-39

There are only two reasons why the fluid level in the reservoir might go down:

The fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up.

. A fluid leak in the brake/clutch

hydraulic system can also cause a low fluid level. Have the brake/ clutch hydraulic system fixed, since a leak means that sooner or later the brakes and/or clutch will not work well.

Do not top off the brake/clutch fluid. Adding fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as necessary, only when work is done on the brake/clutch hydraulic system.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (40,1)

10-40

Vehicle Care

{ Warning

{ Warning

If too much brake fluid is added, it can spill on the engine and burn, if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake fluid only when work is done on the brake/clutch hydraulic system.

When the brake/clutch fluid falls to a low level, the brake warning light comes on. See Brake System Warning Light on page 5-19.

What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 11-12. Always clean the brake/clutch fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.

With the wrong kind of fluid in the brake/clutch hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake/clutch fluid.

{ Caution

. Using the wrong fluid can

badly damage brake/clutch hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid.

(Continued)

Caution (Continued)

. If brake fluid is spilled on the

vehicle's painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle. If you do, wash it off immediately.

Battery The original equipment battery is maintenance free. Do not remove the cap and do not add fluid. The battery is in the trunk, under the floor panel. Refer to the replacement number shown on the original battery label when a new battery is needed.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (41,1)

{ Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Vehicle Storage

{ Warning

Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 10-95 for tips on working around a battery without getting hurt.

Infrequent Usage: Remove the black, negative (−) cable from the battery to keep the battery from running down.

Extended Storage: Remove the black, negative (−) cable from the battery or use a battery trickle charger.

Rear Axle

When to Check Lubricant It is not necessary to regularly check the rear axle fluid, unless a leak is suspected or an unusual noise is heard. A fluid loss could indicate a problem. Have it inspected and repaired by your dealer.

Starter Switch Check

{ Warning When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

Vehicle Care

10-41

1. Before starting this check, be

sure there is enough room around the vehicle.

2. Apply both the parking brake

and the regular brake. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.

3. For automatic transmission

vehicles, try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service. For manual transmission vehicles, put the shift lever in Neutral, push the clutch pedal down halfway, and try to start the engine. The vehicle should start only when the clutch pedal is pushed down all the way to the floor. If the vehicle starts when the clutch pedal is not pushed all the way down, contact your dealer for service.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (42,1)

10-42

Vehicle Care

Automatic Transmission Shift Lock Control Function Check

{ Warning When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

1. Before starting this check, be

sure there is enough room around the vehicle. It should be parked on a level surface.

2. Apply the parking brake. Be

ready to apply the regular brake immediately if the vehicle begins to move.

3. With the engine off, turn the

ignition on, but do not start the engine. Without applying the regular brake, try to move the shift lever out of P (Park) with

normal effort. If the shift lever moves out of P (Park), contact your dealer for service.

Ignition Transmission Lock Check While parked and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position.

The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). The ignition key should come out only in LOCK/OFF.

Contact your dealer if service is required.

Park Brake and P (Park) Mechanism Check { Warning

When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.

Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.

To check the parking brake's holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (43,1)

Vehicle Care

10-43

warranty. Do not allow the wiper blade arm to touch the windshield.

5. Reverse Steps 1–3 for wiper

blade replacement.

Windshield Replacement If the Head-Up display (HUD) system and the windshield need to be replaced, get one that is designed for HUD or the HUD image may look out of focus.

To check the P (Park) mechanism's holding ability: With the engine running, shift to P (Park). Then release the parking brake followed by the regular brake.

Contact your dealer if service is required.

Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking. See Maintenance Schedule on page 11-2 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Maintenance Replacement Parts on page 11-14. To replace the windshield wiper blade: 1. Pull the windshield wiper assembly away from the windshield.

2. Lift up on the latch in the middle

of the wiper blade where the wiper arm attaches.

3. With the latch open, pull the wiper blade down toward the windshield far enough to release it from the J-hooked end of the wiper arm.

4. Remove the wiper blade.

Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not be covered by the vehicle

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (44,1)

10-44

Vehicle Care

Headlamp Aiming Headlamp aim has been preset and should need no further adjustment. If the vehicle is damaged in a crash, the headlamp aim may be affected. If adjustment to the headlamps is necessary, see your dealer.

Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 10-47. For any bulb‐changing procedure not listed in this section, contact your dealer.

Halogen Bulbs

{ Warning

Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.

High Intensity Discharge (HID) Lighting

{ Warning

The high intensity discharge lighting system operates at a very high voltage. If you try to service any of the system components, you could be seriously injured. Have your dealer or a qualified technician service them.

After an HID headlamp bulb has been replaced, the beam might be a slightly different shade than it was originally. This is normal.

Headlamps, Front Turn Signal and Parking Lamps (Uplevel Vehicle) The uplevel model vehicle has an HID headlamp and a turn signal lamp on the headlamp assembly. The parking lamp is also the

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (45,1)

Vehicle Care

10-45

7. Pull the duct back out of the air

cleaner/filter housing until the tabs snap the duct back into position.

Headlamps, Front Turn Signal and Parking Lamps (Base Vehicle) The base model vehicle has a halogen headlamp and a turn signal/parking lamp on the headlamp assembly. To replace one of these bulbs: 1. Open the hood. See Hood on

page 10-5.

function of the HID headlamp. See High Intensity Discharge (HID) Lighting on page 10-44. To replace the turn signal bulb: 1. Open the hood. See Hood on

page 10-5.

3. Disconnect the wiring harness

and turn the bulb socket counterclockwise to remove it from the headlamp assembly. 4. Pull the bulb straight out from

the socket.

5. Push the new bulb into the

socket and reinstall the socket into the headlamp assembly by turning it clockwise.

6. Reconnect the electrical

connector.

2. Press in on the tabs on the sides

of the duct, and then push the duct rearward into the air cleaner/filter housing.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (46,1)

10-46

Vehicle Care

6. Reconnect the electrical

connector.

7. Pull the duct back out of the air

cleaner/filter housing until the tabs snap the duct back into position.

Taillamps, Turn Signal, and Stoplamps To replace a taillamp, turn signal, or stoplamp bulb: 1. Open the trunk. See Trunk on

page 2-10.

2. Remove the close out panel

retainers to gain access to the bulb socket connectors.

3. Turn the bulb socket

counterclockwise to remove it. 4. Pull the old bulb straight out of

the bulb socket.

5. Push the new bulb straight into

the bulb socket until it clicks.

6. Turn the bulb socket clockwise

to reinstall.

2. Press in on the tabs on the sides

of the duct, and then push the duct rearward into the air cleaner/filter housing.

3. Disconnect the wiring harness

and turn the bulb socket counterclockwise to remove it from the headlamp assembly. 4. Pull the bulb straight out from

the socket.

5. Push the new bulb into the

socket and reinstall the socket into the headlamp assembly by turning it clockwise.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (47,1)

License Plate Lamp To replace one of these bulbs:

Vehicle Care

10-47

5. Push the bulb straight into the

socket and turn clockwise to reinstall.

6. Reinstall the license plate lamp

by lifting it through the fascia opening until the clip is in place.

Replacement Bulbs

Exterior Lamp

Rear Turn Signal Lamp

Bulb

Number W21/5W

For replacement bulbs not listed here, contact your dealer.

Exterior Lamp

Front Parking and Turn Signal Lamp (Except ZL1) Front Park and Turn Signal Lamp (ZL1) Low-Beam Headlamp High-Beam Headlamp License Plate Lamp Rear Stoplamps Rear Taillamp

Bulb

Number

T20

3457NAK

H11LL

H9LL

W5WLL

T20

7444LL

1. Unclip the license plate lamp

from the fascia opening.

2. Pull the license plate lamp down

through the fascia opening.

3. Turn the bulb socket

counterclockwise and pull the bulb straight out of the lamp socket. Install the new bulb.

4.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (48,1)

10-48

Vehicle Care

Electrical System

Electrical System Overload The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the chance of circuit overload and fire caused by electrical problems. Fuses and circuit breakers protect power devices in the vehicle. Replace a bad fuse with a new one of the identical size and rating. If there is a problem on the road and a fuse needs to be replaced, the same amperage fuse can be borrowed. Choose some feature of the vehicle that is not needed to use and replace it as soon as possible.

Headlamp Wiring An electrical overload may cause the lamps to go on and off, or in some cases to remain off. Have the headlamp wiring checked right away if the lamps go on and off or remain off. Windshield Wipers If the wiper motor overheats due to heavy snow or ice, the windshield wipers will stop until the motor cools and will then restart. Although the circuit is protected from electrical overload, overload due to heavy snow or ice may cause wiper linkage damage. Always clear ice and heavy snow from the windshield before using the windshield wipers. If the overload is caused by an electrical problem and not snow or ice, be sure to get it fixed.

Fuses and Circuit Breakers The wiring circuits in the vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure to replace a bad fuse with a new one of the identical size and rating. Fuses of the same amperage can be temporarily borrowed from another fuse location, if a fuse goes out. Replace the fuse as soon as possible. To identify and check fuses, circuit breakers, and relays, see Engine Compartment Fuse Block on page 10-49, Instrument Panel Fuse Block on page 10-51, and Rear Compartment Fuse Block on page 10-53.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (49,1)

Vehicle Care

10-49

Engine Compartment Fuse Block

To remove the hinged fuse block cover, press the clip at the front of the cover, and swing it up. { Caution

Spilling liquid on any electrical component on the vehicle may damage it. Always keep the covers on any electrical component.

The vehicle may not be equipped with all of the fuses, relays, and features shown.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (50,1)

10-50

Vehicle Care

Usage

Mini Fuses

J-Case Fuses

12
22

25

26

27
41
43

44

Wiper Starter Brake Vacuum Pump Power Windows Rear Power Windows Front Rear Defog Cooling Fan High Antilock Brake System Pump Cooling Fan Low

Mini Fuses

Usage

Air Conditioning Compressor Clutch Transmission Control Module Intercooler Pump

10
11
14

15
16
17

18

Usage Engine Control Module Main Pre-Catalytic Converter Oxygen Sensor Post-Catalytic Converter Oxygen Sensor Fuel Injectors – Even Fuel Injectors – Odd Cooling Fan Relay Manifold Air Flow/ Chassis Control Ignition Run/Crank IP Sensing Diagnostic Module/Ignition Run/Crank Body

Mini Fuses

19

20

31

32

33

34
35
38
40

46

47

50

Usage Transmission Control Module/ Ignition Engine Control Module/Ignition Outside Rearview Mirror Canister Vent Solenoid Body Control Module 6
Sunroof Front Heated Seats Washer Pump Front Antilock Brake System Valves HID Headlamp – Left Front HID Headlamp – Right Front Fog Lamps

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (51,1)

Vehicle Care

10-51

Micro Relays

Usage

Instrument Panel Fuse Block

K69
K613
K617

K619
K627

K632

K641

Wiper Control Cooling Fan Low Air Conditioning Compressor Clutch Wiper Speed High Intensity Discharge Headlamps Brake Vacuum Pump Intercooler Pump

The instrument panel fuse block is on the end of the instrument panel, on the driver side of the vehicle. To access the fuses, open the fuse panel door by pulling out. To reinstall the door, push the door back into its original location.

Mini Fuses

Usage

51
52
55

56

61

Horn Spare High-Beam Headlamp – Right Front High-Beam Headlamp – Left Front Heated Mirror

Mini Relays

Usage

K26
K50
K55
K612
K614

Micro Relays

Powertrain Run/Crank Rear Defog Cooling Fan High Cooling Fan Control

Usage

K61

Starter

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (52,1)

10-52

Vehicle Care

Fuses

F6

F8
F9
F10
F11
F12
F13
F14

F15

F16

F17
F18
F19

F20

Usage Body Control Module 2
Battery Spare Spare Spare Spare Display OnStar® Universal Hands-Free Phone (If Equipped) Body Control Module 3
Body Control Module 4
Power Outlet 1
Power Outlet 2
Steering Wheel Controls Backlight Spare

The vehicle may not be equipped with all of the fuses, relays, and features shown.

Fuses

F1

F2

Usage Discrete Logic Ignition Switch Diagnostic Link Connector

Fuses

Usage

F3
F4
F5

Airbag Cluster Heating Ventilation Air Conditioning Controller

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (53,1)

Fuses

Usage

F21
F22
F23
F24

F25

F27

F28

F29
F30

Spare Spare Trunk Automatic Occupant Sensing Body Control Module 1
Body Control Module 8
Front Heater, Ventilation, and Air Conditioning Spare Body Control Module 7

Circuit

Breakers

Usage

CB7
CB26

Passenger Seat Driver Seat

Vehicle Care

10-53

net retainers, the rear sill plate, and the passenger side trim retainers, then swing the trim out of the way.

Relays

K10

K609
SPARE

Usage

Retained Accessory Power Trunk SPARE

Rear Compartment Fuse Block

The rear compartment fuse block is on the right side of the trunk behind a cover. Remove the convenience

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (54,1)

10-54

Vehicle Care

Fuses

Usage

F7
F8

F9
F10

F11

F12

Real Time Damping Active Exhaust Flapper Spare 4
Engine Control Module/Battery Regulated Voltage Control Fuel System Control Module

Relays

Usage

R1
R2

Spare Active Exhaust Flapper

The vehicle may not be equipped with all of the fuses, relays, and features shown.

Fuses

F1

Usage

Universal Remote System/Rear Parking Assist/ Inside Rearview Mirror

Fuses

Usage

F2
F3
F4
F5
F6

Amplifier Radio Convertible Top 1
Convertible Top 2
Spare 1

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (55,1)

Wheels and Tires

Tires Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer.

{ Warning

. Poorly maintained and

improperly used tires are dangerous.

. Overloading the tires can

cause overheating as a result of too much flexing. There could be a blowout

(Continued)

Vehicle Care

10-55

Warning (Continued)

Warning (Continued)

and a serious crash. See Vehicle Load Limits on page 9-14.

. Underinflated tires pose

the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when the tires are cold.

. Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when hitting a pothole. Keep tires at the recommended pressure.

(Continued)

. Worn or old tires can

cause a crash. If the tread is badly worn, replace them.

. Replace any tires that

have been damaged by impacts with potholes, curbs, etc.

. Improperly repaired tires can cause a crash. Only the dealer or an authorized tire service center should repair, replace, dismount, and mount the tires.

. Do not spin the tires in

excess of 56 km/h (35 mph) on slippery surfaces such as snow, mud, ice, etc. Excessive spinning may cause the tires to explode.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (56,1)

10-56

Vehicle Care

All-Season Tires This vehicle may come with all-season tires. These tires are designed to provide good overall performance on most road surfaces and weather conditions. Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. Original equipment all-season tires can be identified by the last two characters of this TPC code, which will be “MS.” Consider installing winter tires on the vehicle if frequent driving on snow or ice-covered roads is expected. All-season tires provide adequate performance for most winter driving conditions, but they may not offer the same level of traction or performance as winter tires on snow or ice-covered roads. See Winter Tires on page 10-56.

Winter Tires This vehicle was not originally equipped with winter tires. Winter tires are designed for increased traction on snow and ice-covered roads. Consider installing winter tires on the vehicle if frequent driving on ice or snow covered roads is expected. See your dealer for details regarding winter tire availability and proper tire selection. Also, see Buying New Tires on page 10-73. With winter tires, there may be decreased dry road traction, increased road noise, and shorter tread life. After changing to winter tires, be alert for changes in vehicle handling and braking. If using winter tires: . Use tires of the same brand and

tread type on all four wheel positions.

. Use only radial ply tires of the

same size, load range, and speed rating as the original equipment tires.

Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y, and ZR speed rated tires. If winter tires with a lower speed rating are chosen, never exceed the tire's maximum speed capability.

Low-Profile Tires If the vehicle has 305/30ZR19
size tires, they are classified as low-profile tires.

{ Caution Low-profile tires are more susceptible to damage from road hazards or curb impact than standard profile tires. Tire and/or wheel assembly damage can occur when coming into contact

(Continued)

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (57,1)

Caution (Continued)

with road hazards like potholes, or sharp edged objects, or when sliding into a curb. The warranty does not cover this type of damage. Keep tires set to the correct inflation pressure and when possible, avoid contact with curbs, potholes, and other road hazards.

Competition Oriented Tires This vehicle may come with 305/ 30ZR19 competition oriented tires that are DOT approved for street use. Competition oriented tires use a special tread pattern and compound that provide more grip than normal road tires. The minimum tread depth will be reached earlier than typical tires, resulting in reduced tire life. This special tread pattern and compound will have decreased performance in

cold climates, heavy rain, and standing water. We recommend installing winter tires on the vehicle when driving at temperatures below approximately 10°C (50°F) or on ice or snow covered roads. See Winter Tires on page 10-56.

{ Warning

Driving on wet roads, in heavy rain, or through standing water with competition oriented tires may cause hydroplaning and loss of control. Use extreme caution and drive slowly on wet roads.

{ Warning

Driving with competition oriented tires on snow, ice, or cold road surfaces can cause loss of control or an accident. Competition oriented tires are summer season tires and are not intended to be

(Continued)

Vehicle Care

10-57

Warning (Continued)

driven on snow, ice, or road surfaces below 10°C (50°F). Do not drive a vehicle with competition oriented tires in these conditions.

{ Caution

Competition oriented tires have rubber compounds that lose flexibility and may develop surface cracks in the tread area at temperatures below -7°C (20° F). Always store competition oriented tires indoors and at temperatures above -7°C (20°F) when not in use. If the tires have been subjected to -7°C (20°F) or less, let them warm up in a heated space to at least 10°C (50°F) for 24 hours or more before being installed or driving a (Continued)

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (58,1)

10-58

Vehicle Care

Caution (Continued)

vehicle on which they are installed. Do not apply heat or blow heated air directly on the tires. Always inspect tires before use. See Tire Inspection on page 10-70.

Summer Tires

High Performance Summer Tires This vehicle may come with 245/ 45ZR20 and 275/40ZR20, 245/ 40ZR21 and 275/35ZR21, or 285/ 35ZR20 and 305/35ZR20 high performance summer tires. These tires have a special tread and compound that are optimized for maximum dry and wet road performance. This special tread and compound will have decreased performance in cold climates, and on ice and snow. We recommend installing winter tires on the vehicle if frequent driving at temperatures below approximately 5°C (40°F) or

on ice or snow covered roads is expected. See Winter Tires on page 10-56.

{ Caution

High performance summer tires have rubber compounds that lose flexibility and may develop surface cracks in the tread area at temperatures below -7°C (20° F). Always store high performance summer tires indoors and at temperatures above -7°C (20°F) when not in use. If the tires have been subjected to -7°C (20°F) or less, let them warm up in a heated space to at least 5°C (40°F) for 24 hours or more before being installed or driving a vehicle on which they are installed. Do not apply heat or blow heated air directly on the tires. Always inspect tires before use. See Tire Inspection on page 10-70.

Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples show a typical passenger vehicle tire and a compact spare tire sidewall.

Passenger (P-Metric) Tire Example (1) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type,

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (59,1)

and service description. See the “Tire Size” illustration later in this section. (2) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. (3) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. DOT Tire Date of Manufacture: The last four digits of the TIN indicate the tire manufactured date. The first two

digits represent the week (01– 52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. (4) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (5) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (6) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three

Vehicle Care

10-59

performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 10-75. (7) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.

Compact Spare Tire Example (1) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (60,1)

10-60

Vehicle Care

(2) Temporary Use Only: The compact spare tire or temporary use tire should not be driven at speeds over 80 km/h (50 mph). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat. If the vehicle has a compact spare tire, see Compact Spare Tire on page 10-94 and If a Tire Goes Flat on page 10-78. (3) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.

(4) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. (5) Tire Inflation: The temporary use tire or compact spare tire should be inflated to 420 kPa (60 psi). For more information on tire pressure and inflation see Tire Pressure on page 10-64. (6) Tire Size: A combination of letters and numbers define a tire's width, height, aspect ratio, construction type, and service description. The letter T as the first character in the tire size means the tire is for temporary use only. (7) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance

criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.

Tire Designations

Tire Size The following is an example of a typical passenger vehicle tire size.

(1) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (61,1)

vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (2) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (3) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item 3 of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide. (4) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction.

(5) Rim Diameter: Diameter of the wheel in inches. (6) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.

Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight: The combined weight of optional accessories. Some examples of optional accessories are

Vehicle Care

10-61

automatic transmission, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at