2015 Chevrolet Camaro Owners Manual

one-half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (76,1)

10-76

Vehicle Care

their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not

overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing are not necessary on a regular basis. Consider an alignment check if there is unusual tire wear or the vehicle is significantly pulling to one side or the other. Some slight pull to the left or right, depending on the crown of the road and/or other road surface variations such as troughs or ruts, is normal. If the vehicle is vibrating when driving on a smooth road, the tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (77,1)

Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.

Vehicle Care

10-77

{ Warning

Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.

Used Replacement Wheels

{ Warning

Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.

{ Caution

Tire Chains

The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, rear differential, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis.

See If a Tire Goes Flat on page 10-78 for more information.

{ Warning

Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause loss of

(Continued)

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (78,1)

10-78

Vehicle Care

Warning (Continued)

control and a crash. Use another type of traction device only if its manufacturer recommends it for the vehicle's tire size combination and road conditions. Follow that manufacturer's instructions. To avoid vehicle damage, drive slowly and readjust or remove the traction device if it contacts the vehicle. Do not spin the wheels. If traction devices are used, install them on the rear tires.

If a Tire Goes Flat It is unusual for a tire to blow out while driving, especially if the tires are maintained properly. See Tires on page 10-55. If air goes out of a tire, it is much more likely to leak out slowly. But if there is ever a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.

{ Warning

Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.

{ Warning

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for (Continued)

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (79,1)

Warning (Continued)

Warning (Continued)

changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-4.

{ Warning Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall causing injury or death. Find a level place to change the tire. To help prevent the vehicle from moving:

(Continued)

1. Set the parking brake firmly. 2. Put an automatic

transmission in P (Park) or a manual transmission in 1 (First) or R (Reverse).

3. Turn off the engine and do not restart while the vehicle is raised.

4. Do not allow passengers to

remain in the vehicle.

5. Place wheel blocks,

if equipped, on both sides of the tire at the opposite corner of the tire being changed.

This vehicle may come with a jack and spare tire or a tire sealant and compressor kit. To use the jacking equipment to change a spare tire safely, follow the instructions below. Then see Tire Changing on page 10-88. To use the tire sealant

Vehicle Care

10-79

and compressor kit, see Tire Sealant and Compressor Kit on page 10-80. When the vehicle has a flat tire (2), use the following example as a guide to assist you in the placement of wheel blocks (1), if equipped.

1. Wheel Block (If Equipped) 2. Flat Tire

The following information explains how to repair or change a tire.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (80,1)

10-80

Vehicle Care

Tire Sealant and Compressor Kit

{ Warning

Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 9-27.

{ Warning

Overinflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant (Continued)

Warning (Continued)

and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure.

{ Warning

Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.

Tire sealant may not completely seal a 305/35ZR20 tire below –18°C (0°F).

If this vehicle has a tire sealant and compressor kit, there may not be a spare tire or tire changing equipment, and on some vehicles there may not be a place to store a tire. The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (0.25 in) in the tread area of the tire. It can also be used to inflate an underinflated tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program on page 13-5. Read and follow all of the tire sealant and compressor kit instructions.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (81,1)

The kit includes:

1. Sealant Canister Inlet Valve 2. Sealant/Air Hose 3. Base of Sealant Canister 4. Tire Sealant Canister 5. On/Off Button 6. Slot on Top of Compressor 7. Pressure Deflation Button 8. Pressure Gauge

9. Power Plug 10. Air Only Hose

Tire Sealant Read and follow the safe handling instructions on the label adhered to the tire sealant canister (4). Check the tire sealant expiration date on the tire sealant canister. The tire sealant canister (4) should be replaced before its expiration date. Replacement tire sealant canisters are available at your local dealer.

Vehicle Care

10-81

There is only enough sealant to seal one tire. After usage, the tire sealant canister must be replaced. Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-4. See If a Tire Goes Flat on page 10-78 for other important safety warnings. Do not remove any objects that have penetrated the tire.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (82,1)

10-82

Vehicle Care

1. Remove the tire sealant

canister (4) and compressor from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10-87. 2. Remove the air only hose (10)

and the power plug (9) from the bottom of the compressor.

3. Place the compressor on the

ground near the flat tire.

4. Attach the air only hose (10) to

the sealant canister inlet valve (1) by turning it clockwise until tight.

5. Slide the base of the tire sealant

7. Attach the sealant/air hose (2) to

the tire valve stem by turning it clockwise until tight.

canister (3) into the slot on the top of the compressor (6) to hold it upright. Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

6. Remove the valve stem cap from

the flat tire by turning it counterclockwise.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (83,1)

8. Plug the power plug (9) into the

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5-5. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

9. Start the vehicle. The vehicle

must be running while using the air compressor.

10. Press the on/off button (5) to

turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gauge (8) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the

11.

pressure will quickly drop and start to rise again as the tire inflates with air only. Inflate the tire to the recommended inflation pressure using the pressure gauge (8). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10-64. The pressure gauge (8) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached.

{ Caution

If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven

(Continued)

Vehicle Care

10-83

Caution (Continued)

farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program on page 13-5.

12. Press the on/off button (5) to

turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire. Therefore, Steps 13–21 must be done immediately after Step 12. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (84,1)

10-84

Vehicle Care

13. Unplug the power plug (9) from

the accessory power outlet in the vehicle.

14. Turn the sealant/air hose (2)

counterclockwise to remove it from the tire valve stem.

15. Replace the tire valve

stem cap.

16. Remove the tire sealant

canister (4) from the slot on top of the compressor (6).

17. Turn the air only hose (10)

counterclockwise to remove it from the tire sealant canister inlet valve (1).

18. Turn the sealant/air hose (2)

clockwise onto the sealant canister inlet valve (1) to prevent sealant leakage.

19. Return the air only hose (10)

and power plug (9) back to their original storage location.

20.

If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister and place it in a highly visible location. Do not exceed the speed on this label until the damaged tire is repaired or replaced.

21. Return the equipment to its

22.

original storage location in the vehicle. Immediately drive the vehicle 8 km (5 mi) to distribute the sealant in the tire.

23. Stop at a safe location and

check the tire pressure. Refer to Steps 1–10 under “Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured).” If the tire pressure has fallen more than 68 kPa (10 psi) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program on page 13-5. If the tire pressure has not dropped more than 68 kPa (10 psi) from the recommended inflation pressure, inflate the tire to the recommended inflation pressure.

24. Wipe off any sealant from the

wheel, tire, or vehicle.

25. Dispose of the used tire

sealant canister (4) at a local dealer or in accordance with local state codes and practices.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (85,1)

Vehicle Care

10-85

26. Replace it with a new canister

available from your dealer.

27. After temporarily sealing a tire

using the tire sealant and compressor kit, take the vehicle to an authorized dealer within 161 km (100 mi) of driving to have the tire repaired or replaced.

Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) The kit includes:

9. Power Plug 10. Air Only Hose

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-4. See If a Tire Goes Flat on page 10-78 for other important safety warnings. 1. Remove the compressor from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10-87.

1. Sealant Canister Inlet Valve 2. Sealant/Air Hose 3. Base of Sealant Canister 4. Tire Sealant Canister 5. On/Off Button 6. Slot on Top of Compressor 7. Pressure Deflation Button 8. Pressure Gauge

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (86,1)

10-86

Vehicle Care

2. Remove the air only hose (10)

and the power plug (9) from the bottom of the compressor.

3. Place the compressor on the

ground near the flat tire. Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

4. Remove the valve stem cap from

the flat tire by turning it counterclockwise.

5. Attach the air only hose (10) to the tire valve stem by turning it clockwise until tight.

6. Plug the power plug (9) into the

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5-5. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter.

Do not pinch the power plug cord in the door or window.

7. Start the vehicle. The vehicle

must be running while using the air compressor.

8. Press the on/off button (5) to

9.

turn the tire sealant and compressor kit on. The compressor will inflate the tire with air only. Inflate the tire to the recommended inflation pressure using the pressure gauge (8). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10-64. The pressure gauge (8) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached.

{ Caution

If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program on page 13-5.

10. Press the on/off button (5) to

turn the tire sealant and compressor kit off. Be careful while handling the compressor as it could be warm after usage.

11. Unplug the power plug (9) from

the accessory power outlet in the vehicle.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (87,1)

Vehicle Care

10-87

12. Turn the air only hose (10)

counterclockwise to remove it from the tire valve stem.

13. Replace the tire valve

stem cap.

14. Return the air only hose (10)

and power plug (9) back to their original storage location.

15. Return the equipment to its

original storage location in the vehicle.

The tire sealant and compressor kit has accessory adapters located in a compartment on the bottom of its housing that can be used to inflate air mattresses, balls, etc.

Storing the Tire Sealant and Compressor Kit The tire sealant and compressor kit is in a case in the trunk. 1. Open the trunk. See Trunk on

page 2-10.

2. Remove the carpet.

3. Turn the center retainer

counterclockwise to remove the cover.

4. Remove the tire sealant and

compressor kit case.

5. Open the case.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (88,1)

10-88

Vehicle Care

6. Remove the compressor (1) and

3. Turn the center retainer

counterclockwise to remove the spare tire cover.

4. Remove the spare tire and place it next to the tire being changed.

Tools The jack and tools are stored below the spare tire.

the sealant canister (2). To store the tire sealant and compressor kit, reverse the steps.

Tire Changing

Removing the Spare Tire and Tools

Spare Tire 1. Open the trunk. See Trunk on

page 2-10.

2. Remove the carpet.

Coin/Pierce Jack with Two-Piece

Wrench

1. Tool Container 2. Two-Piece Wrench 3. Strap 4. Jack Handle Extension 5. Coin/Pierce Jack

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (89,1)

Vehicle Care

10-89

Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before

proceeding. See If a Tire Goes Flat on page 10-78 for more information. If the vehicle has wheel bolt caps, remove the caps. Store the caps with the wheel cover.

2.

3. Use the fully extended wheel

wrench to loosen all the wheel nuts one-half turn counterclockwise. Do not remove them yet.

Hex-Head Jack with Three-Piece

Wrench

1. Tool Container 2. Three-Piece Wrench 3. Strap 4. Hex Head Jack

1. Tool Container 2. Jack 3. End of the Jack

1. Turn the end of the jack (3)

counterclockwise to loosen it. Remove the jack (2) from the retaining bracket.

2. Remove the tool container (1). 3. Remove the tools and tire strap

from the tool container.

4. Place the tools next to the tire

being changed.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (90,1)

10-90

Vehicle Care

{ Caution

Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty.

4. Position the jack lift head at the jack location nearest the flat tire. The location is indicated by a mark on the bottom edge of the vehicle. The jack must not be used in any other position. Raise the jack until it engages with the jacking point. { Warning

Getting under a vehicle when it is lifted on a jack is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

{ Warning

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the

(Continued)

Warning (Continued)

appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

{ Warning

Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (91,1)

5.

If you have a coin/pierce jack, attach the jack handle extension to the jack by sliding the hook through the end of the jack and insert the other end of the jack handle into the wrench. If you have a hex head jack, place the hex tube end of the wrench over the hex head of the jack.

Coin/Pierce Jack and Wrench

Vehicle Care

10-91

6. Raise the vehicle by turning the

wrench clockwise until the vehicle is far enough off the ground to allow enough room for the compact spare tire to fit under the vehicle. Keep the hook parallel to the ground. The wrench may need to be removed and repositioned to continue turning it.

Hex Head Jack and Wrench

7. Remove all of the wheel nuts and place them in a dry, clean place to avoid getting dirt in the threads.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (92,1)

10-92

Vehicle Care

{ Warning

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

10. Reinstall the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each nut as much as possible using the wheel wrench until the wheel is held firmly against the hub. Use your free hand to prevent the wheel from turning while you are tightening.

11. Lower the vehicle by turning

the wrench counterclockwise. Lower the jack completely.

8. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel.

9. Place the compact spare tire on

the wheel-mounting surface.

{ Warning

Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (93,1)

Vehicle Care

10-93

To store a flat or spare tire and tools: 1. Return the jack and tools as they

were originally stored in the trunk.

2. Return the spare tire cover as it

3.

was in the trunk. Install the retainer nut and turn it clockwise until tight.

4. Return the rear trunk carpet. 5. Place the flat tire face up on the

load floor.

12. Tighten the wheel nuts firmly in

a crisscross sequence, as shown.

{ Warning

Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12-2 for original equipment wheel nut torque specifications.

{ Caution

Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 12-2 for the wheel nut torque specification.

Storing a Flat or Spare Tire and Tools

{ Warning

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (94,1)

10-94

Vehicle Care

6. Route the strap provided, as shown, to secure the flat tire.

The compact spare tire is for temporary use only. Replace the compact spare with a full-size tire as soon as possible.

Compact Spare Tire

{ Warning

Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.

If this vehicle has a compact spare tire, it was fully inflated when new; however, it can lose air over time. Check the inflation pressure regularly. It should be 420 kPa (60 psi).

Stop as soon as possible and check that the spare tire is correctly inflated after being installed on the vehicle. The compact spare tire is designed for temporary use only. The vehicle will perform differently with the spare tire installed and it is recommended that the vehicle speed be limited to 80 km/h (50 mph). To conserve the tread of the spare tire, have the standard tire repaired or replaced as soon as convenient and return the spare tire to the storage area. When using a compact spare tire, the ABS and Traction Control systems may engage until the spare tire is recognized by the vehicle, especially on slippery roads. Adjust driving to reduce possible wheel slip.

{ Caution

When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails which can damage the tire, wheel, and other parts of the vehicle.

Do not use the compact spare on other vehicles. Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together.

{ Caution

Tire chains will not fit the compact spare. Using them can damage the vehicle and the chains. Do not use tire chains on the compact spare.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (95,1)

Jump Starting For more information about the vehicle battery, see Battery on page 10-40. If the battery has run down, try to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.

{ Warning

Batteries can hurt you. They can be dangerous because:

. They contain acid that can

burn you.

. They contain gas that can

explode or ignite.

. They contain enough electricity to burn you.

If you do not follow these steps exactly, some or all of these things can hurt you.

{ Caution

Ignoring these steps could result in costly damage to the vehicle that would not be covered by the vehicle warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle.

Vehicle Care

10-95

The jump start remote positive (1) and negative (2) terminals are in the engine compartment on the driver side of the vehicle. These terminals are used instead of a direct connection to the battery. The positive jump start connection is covered by a red cap. Remove to expose the terminal. 1. Check the other vehicle. It must

have a 12-volt battery with a negative ground system.

{ Caution

If the other vehicle does not have a 12-volt system with a negative ground, both vehicles can be damaged. Only use a vehicle that has a 12-volt system with a negative ground for jump starting.

1. Remote Positve (+) Terminal 2. Remote Negative (-) Terminal

2. Position the two vehicles so that

they are not touching.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (96,1)

10-96

Vehicle Care

3. Set the parking brake firmly.

Vehicles with an automatic transmission should be in P (Park). See Shifting Into Park on page 9-24. Vehicles with a manual transmission should be in Neutral. See Parking (Manual Transmission) on page 9-26.

{ Caution

If any accessories are left on or plugged in during the jump starting procedure, they could be damaged. The repairs would not be covered by the vehicle warranty. Whenever possible, turn off or unplug all accessories on either vehicle when jump starting.

4. Turn the ignition to LOCK/OFF

and switch off all lights and accessories in both vehicles, except the hazard warning flashers if needed.

{ Warning

{ Warning

An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.

{ Warning

Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.

Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.

5. Connect one end of the red

positive (+) cable to the jump start positive (+) post.

6. Connect the other end of the red

positive (+) cable to the positive (+) terminal of the good battery.

7. Connect one end of the black

negative (–) cable to the negative (–) terminal of the good battery.

8. Connect the other end of the

black negative (–) cable to the negative (–) post.

9. Start the engine in the vehicle with the good battery and run the engine at idle speed for at least four minutes.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (97,1)

Towing the Vehicle

{ Caution

Incorrectly towing a disabled vehicle may cause damage. The damage would not be covered by the vehicle warranty.

Have the vehicle towed on a flatbed car carrier. A wheel lift tow truck could damage the vehicle.

Vehicle Care

10-97

Due to low ramp angles on the ZL1 and Z/28, use care when loading the vehicle onto a flatbed carrier. Front spring spacers were provided for lifting the front suspension if more clearance is necessary when towing. Consult your dealer or a professional towing service if the disabled vehicle must be towed. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motor home, see “Recreational Vehicle Towing” following.

10. Try to start the vehicle that had

the dead battery. If it will not start after a few tries, it probably needs service.

{ Caution If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.

Jumper Cable Removal Reverse the sequence exactly when removing the jumper cables.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (98,1)

10-98

Vehicle Care

Recreational Vehicle Towing

{ Caution

Dolly towing or dinghy towing the vehicle may cause damage because of reduced ground clearance. Always put the vehicle on a flatbed truck or trailer.

The vehicle was neither designed nor intended to be towed with any of its wheels on the ground. If the vehicle must be towed, see Towing the Vehicle on page 10-97.

Appearance Care

Exterior Care

Locks Locks are lubricated at the factory. Use a de-icing agent only when absolutely necessary, and have the locks greased after using. See Recommended Fluids and Lubricants on page 11-12. Washing the Vehicle To preserve the vehicle's finish, wash it often and out of direct sunlight.

{ Caution

Do not use petroleum-based, acidic, or abrasive cleaning agents as they can damage the vehicle's paint, metal, or plastic parts. If damage occurs, it would not be covered by the vehicle warranty. Approved cleaning

(Continued)

Caution (Continued)

products can be obtained from your dealer. Follow all manufacturer directions regarding correct product usage, necessary safety precautions, and appropriate disposal of any vehicle care product.

{ Caution Avoid using high-pressure washes closer than 30 cm (12 in) to the surface of the vehicle. Use of power washers exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals.

This symbol e is on any underhood compartment electrical center that should not be power

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (99,1)

washed. This could cause damage that would not be covered by the vehicle warranty.

{ Caution

Vehicles equipped with the 1LE, ZL1, or Z/28 package or any accessory ground effects package have reduced ground clearance. Damage can occur in automatic car washes, when approaching curbs, or on steep inclines. Do not use automatic car washes. Approach curbs and inclines with caution.

If using an automatic car wash, comply with the car wash instructions. The windshield wiper and rear window wiper, if equipped, must be off. Remove any accessories that may be damaged or interfere with the car wash equipment.

Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. Finish Care Application of aftermarket clearcoat sealant/wax materials is not recommended. If painted surfaces are damaged, see your dealer to have the damage assessed and repaired. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter.

Vehicle Care

10-99

Occasional hand waxing or mild polishing should be done to remove residue from the paint finish. See your dealer for approved cleaning products. Do not apply waxes or polishes to uncoated plastic, vinyl, rubber, decals, simulated wood, or flat paint as damage can occur.

{ Caution Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle.

To keep the paint finish looking new, keep the vehicle garaged or covered whenever possible.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (100,1)

10-100

Vehicle Care

Protecting Exterior Bright Metal Moldings

{ Caution

Failure to clean and protect the bright metal moldings can result in a hazy white finish or pitting. This damage would not be covered by the vehicle warranty.

The bright metal moldings on the vehicle are aluminum or stainless steel. To prevent damage always follow these cleaning instructions: . Be sure the molding is cool to the touch before applying any cleaning solution.

. Use a cleaning solution

approved for aluminum or stainless steel. Some cleaners are highly acidic or contain alkaline substances and can damage the moldings.

. Always dilute a concentrated

cleaner according to the manufacturer’s instructions.

. Do not use chrome cleaners. . Do not use cleaners that are not

intended for automotive use.

. Use a nonabrasive wax on the vehicle after washing to protect and extend the molding finish.

Hood Air Extractor

SS, 1LE Shown, Z/28 Similar It is not recommended that the air extractor on the ZL1, SS, 1LE, and Z/28 Performance Packages be waxed, as it will change the gloss level of the surface. In addition, care must be used when waxing around the air extractor. If a small amount of wax is applied to the extractor it can create an irregular appearance in the surface of the panel. If wax, debris, or other materials create stains on the air extractor, see your dealer for the recommended cleaner.

ZL1

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (101,1)

The air extractor may have vent screens in the openings. Keep leaves or other debris out of the vent screens.

{ Caution

Pushing on the vent screens could damage them. Do not push on the screens when clearing.

There is a water deflector on the underside of the air extractor. Do not remove it. Convertible Top Care Frequently hand wash convertible tops with mild car wash soap. Never use a stiff brush, steam, bleach, or aggressive cleaners. If necessary, a soft brush can be used to remove dirt. When finished cleaning, thoroughly rinse the fabric. Avoid automatic car washes with overhead brushes or very high pressure sprays as they can cause damage and leaking.

Only lower the top when it is completely dry and avoid leaving the top lowered for extended periods of time to prevent excessive interior weathering. Avoid leaving large amounts of snow on the top for extended periods of time as damage may also occur. Cleaning Exterior Lamps/ Lenses, Emblems, Decals and Stripes Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps, lenses, emblems, decals and stripes. Follow instructions under "Washing the Vehicle" previously in this section. Lamp covers are made of plastic, and some have a UV protective coating. Do not clean or wipe them when dry. Do not use any of the following on lamp covers: . Abrasive or caustic agents.

Vehicle Care

10-101

. Washer fluids and other cleaning

agents in higher concentrations than suggested by the manufacturer.

. Solvents, alcohols, fuels, or other harsh cleaners. Ice scrapers or other hard items. . Aftermarket appearance caps or

covers while the lamps are illuminated, due to excessive heat generated.

{ Caution

Failure to clean lamps properly can cause damage to the lamp cover that would not be covered by the vehicle warranty.

{ Caution

Using wax on low gloss black finish stripes can increase the gloss level and create a

(Continued)

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (102,1)

10-102

Vehicle Care

Caution (Continued)

non-uniform finish. Clean low gloss stripes with soap and water only.

Air Intakes Clear debris from the air intakes, between the hood and windshield, when washing the vehicle. Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean rubber blades using lint-free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking.

Replace the wiper blades if they are worn or damaged. Damage can be caused by extreme dusty conditions, sand, salt, heat, sun, snow, and ice. Weatherstrips Apply Dielectric silicone grease on weatherstrips to make them last longer, seal better, and not stick or squeak. Lubricate weatherstrips at least once a year. Hot, dry climates may require more frequent application. Black marks from rubber material on painted surfaces can be removed by rubbing with a clean cloth. See Recommended Fluids and Lubricants on page 11-12. Tires Use a stiff brush with tire cleaner to clean the tires.

{ Caution

Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/ or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.

Wheels and Trim — Aluminum or Chrome Use a soft, clean cloth with mild soap and water to clean the wheels. After rinsing thoroughly with clean water and dry with a soft, clean towel. A wax may then be applied.

{ Caution

Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium,

(Continued)

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (103,1)

Caution (Continued)

or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash the chrome with soap and water after exposure.

{ Caution

To avoid surface damage, do not use strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels. Use only approved cleaners. Also, never drive a vehicle with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes. Damage could occur and the repairs would not be covered by the vehicle warranty.

Steering, Suspension, and Chassis Components Visually inspect steering, suspension, and chassis components for damaged, loose, or missing parts or signs of wear at least once a year. Inspect power steering for proper hook-up, binding, leaks, cracks, chafing, etc. Visually check constant velocity joint boots and axle seals for leaks. Body Component Lubrication Lubricate all key lock cylinders, hood hinges, liftgate hinges, and steel fuel door hinge unless the components are plastic. Applying silicone grease on weatherstrips with a clean cloth will make them last longer, seal better, and not stick or squeak. Underbody Maintenance At least twice a year, spring and fall use plain water to flush any corrosive materials from the

Vehicle Care

10-103

underbody. Take care to thoroughly clean any areas where mud and other debris can collect. Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty. Finish Damage Quickly repair minor chips and scratches with touch-up materials available from your dealer to avoid corrosion. Larger areas of finish damage can be corrected in your dealer's body and paint shop.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (104,1)

10-104

Vehicle Care

Chemical Paint Spotting Airborne pollutants can fall upon and attack painted vehicle surfaces causing blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. See “Finish Care” previously in this section.

Interior Care To prevent dirt particle abrasions, regularly clean the vehicle's interior. Immediately remove any soils. Note that newspapers or dark garments that can transfer color to home furnishings can also permanently transfer color to the vehicle's interior. Use a soft bristle brush to remove dust from knobs and crevices on the instrument cluster. Using a mild soap solution, immediately remove hand lotions, sunscreen, and insect repellent from all interior surfaces or permanent damage may result.

Your dealer may have products for cleaning the interior. Use cleaners specifically designed for the surfaces being cleaned to prevent permanent damage. Apply all cleaners directly to the cleaning cloth. Do not spray cleaners directly on any switches or controls. Cleaners should be removed quickly. Never allow cleaners to remain on the surface being cleaned for extended periods of time. Cleaners may contain solvents that can become concentrated in the interior. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning the interior, maintain adequate ventilation by opening the doors and windows. To prevent damage, do not clean the interior using the following cleaners or techniques: . Never use a razor or any other

sharp object to remove a soil from any interior surface.

. Never use a brush with stiff

bristles.

. Never rub any surface

aggressively or with excessive pressure.

. Do not use laundry detergents or

dishwashing soaps with degreasers. For liquid cleaners, use approximately 20 drops per 3.8 L (1 gal) of water. A concentrated soap solution will leave a residue that creates streaks and attracts dirt. Do not use solutions that contain strong or caustic soap.

. Do not heavily saturate the upholstery when cleaning.

. Do not use solvents or cleaners

containing solvents.

Interior Glass To clean, use a terry cloth fabric dampened with water. Wipe droplets left behind with a clean dry cloth. Commercial glass cleaners may be used, if necessary, after cleaning the interior glass with plain water.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (105,1)

{ Caution

To prevent scratching, never use abrasive cleaners on automotive glass. Abrasive cleaners or aggressive cleaning may damage the rear window defogger.

Cleaning the windshield with water during the first three to six months of ownership will reduce tendency to fog. Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap. Coated Moldings Coated moldings should be cleaned. . When lightly soiled, wipe with a

sponge or soft lint-free cloth dampened with water.

. When heavily soiled, use warm

soapy water.

Fabric/Carpet/Suede Start by vacuuming the surface using a soft brush attachment. If a rotating brush attachment is being used during vacuuming, only use it on the floor carpet. Before cleaning, gently remove as much of the soil as possible using one of the following techniques: . Gently blot liquids with a paper towel. Continue blotting until no more soil can be removed. For solid soils, remove as much as possible prior to vacuuming.

To clean: 1. Saturate a clean lint-free colorfast cloth with water. Microfiber cloth is recommended to prevent lint transfer to the fabric or carpet.

2. Remove excess moisture by

gently wringing until water does not drip from the cleaning cloth.

Vehicle Care

10-105

3. Start on the outside edge of the

soil and gently rub toward the center. Fold the cleaning cloth to a clean area frequently to prevent forcing the soil in to the fabric.

4. Continue gently rubbing the soiled area until there is no longer any color transfer from the soil to the cleaning cloth. If the soil is not completely removed, use a mild soap solution followed only by plain water.

5.

If the soil is not completely removed, it may be necessary to use a commercial upholstery cleaner or spot lifter. Test a small hidden area for colorfastness before using a commercial upholstery cleaner or spot lifter. If ring formation occurs, clean the entire fabric or carpet. Following the cleaning process, a paper towel can be used to blot excess moisture.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (106,1)

10-106

Vehicle Care

Cleaning High Gloss Surfaces and Vehicle Information and Radio Displays For vehicles with high gloss surfaces or vehicle displays, use a microfiber cloth to wipe surfaces. Before wiping the surface with the microfiber cloth, use a soft bristle brush to remove dirt that could scratch the surface. Then use the microfiber cloth by gently rubbing to clean. Never use window cleaners or solvents. Periodically hand wash the microfiber cloth separately, using mild soap. Do not use bleach or fabric softener. Rinse thoroughly and air dry before next use.

{ Caution

Do not attach a device with a suction cup to the display. This may cause damage and would not be covered by the vehicle warranty.

Instrument Panel, Leather, Vinyl, Other Plastic Surfaces, Low Gloss Paint Surfaces and Natural Open Pore Wood Surfaces Use a soft microfiber cloth dampened with water to remove dust and loose dirt. For a more thorough cleaning, use a soft microfiber cloth dampened with a mild soap solution.

{ Caution

Soaking or saturating leather, especially perforated leather, as well as other interior surfaces, may cause permanent damage. Wipe excess moisture from these surfaces after cleaning and allow them to dry naturally. Never use heat, steam, or spot removers. Do not use cleaners that contain silicone or wax-based products. Cleaners containing these

(Continued)

Caution (Continued)

solvents can permanently change the appearance and feel of leather or soft trim, and are not recommended.

Do not use cleaners that increase gloss, especially on the instrument panel. Reflected glare can decrease visibility through the windshield under certain conditions. { Caution

Use of air fresheners may cause permanent damage to plastics and painted surfaces. If an air freshener comes in contact with any plastic or painted surface in the vehicle, blot immediately and clean with a soft cloth dampened with a mild soap solution. Damage caused by air fresheners would not be covered by the vehicle warranty.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (107,1)

Vehicle Care

10-107

. Do not use a floor mat if the

vehicle is not equipped with a floor mat retainer on the driver side floor.

. Use the floor mat with the

correct side up. Do not turn it over.

. Do not place anything on top of

the driver side floor mat.

. Use only a single floor mat on

the driver side.

. Do not place one floor mat on

top of another.

Both floor mats are held in place by two hook-type retainers.

Cargo Cover and Convenience Net Wash with warm water and mild detergent. Do not use chlorine bleach. Rinse with cold water, and then dry completely. Care of Safety Belts Keep belts clean and dry. { Warning

Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.

Floor Mats

{ Warning

If a floor mat is the wrong size or is not properly installed, it can interfere with the pedals. Interference with the pedals can cause unintended acceleration and/or increased stopping distance which can cause a crash and injury. Make sure the floor mat does not interfere with the pedals.

Use the following guidelines for proper floor mat usage.

The original equipment floor mats were designed for your vehicle. If the floor mats need replacing, it is recommended that GM certified floor mats be purchased. Non-GM floor mats may not fit properly and may interefere with the pedals. Always check that the floor mats do not interfere with the pedals.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (108,1)

10-108

Vehicle Care

Removing and Replacing the Floor Mats 1. Pull up on the rear of the mat to

remove it from the hooks.

2. Reinstall by lining up the floor mat retainer openings over the carpet retainers and hook into position.

3. Make sure the floor mat is

properly secured and verify that it does not interfere with the pedals.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (1,1)

Service and