2015 Chevrolet Camaro Owners Manual

4. Reverse Steps 1–3 to reinstall

the engine cover.

6.2L V8 Engine Cover (ZL1 Only)

To remove: 1. Lift the engine cover to disengage from the five attachment points.

2. Pull the engine cover forward to

remove.

3. Reverse the steps to reinstall the

engine cover.

7.0L V8 Engine (Z/28)

1. Engine Oil Fill Cap 2. Engine Cover

To remove: 1. Remove the engine oil

fill cap (1).

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (15,1)

Vehicle Care

10-15

to drain back into the oil pan. Checking the oil level too soon after engine shutoff will not provide an accurate oil level reading.

{ Warning

The engine oil dipstick handle may be hot; it could burn you. Use a towel or glove to touch the dipstick handle.

2. Pull out the dipstick and wipe it

with a clean paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level.

To remove the engine covers: 1. Lift the outboard edge of each

engine cover to disengage from two of the four attachment points.

2. Lift the inboard edge of each

engine cover to disengage from two of the four attachment points.

3. Pull each engine cover forward

to remove.

4. Reverse Steps 1–3 to reinstall

each engine cover.

Engine Oil To ensure proper engine performance and long life, careful attention must be paid to engine oil. Following these simple, but important steps will help protect your investment: . Always use engine oil approved to the proper specification and of the proper viscosity grade. See “Selecting the Right Engine Oil” in this section.

. Check the engine oil level regularly and maintain the proper oil level. See “Checking Engine Oil” and “When to Add Engine Oil” in this section.

. Change the engine oil at the

appropriate time. See Engine Oil Life System on page 10-19. . Always dispose of engine oil

properly. See “What to Do with Used Oil” in this section.

Checking Engine Oil (Except Z/28) It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the vehicle must be on level ground. The engine oil dipstick handle is a loop. See Engine Compartment Overview on page 10-6 for the location of the engine oil dipstick. Obtaining an accurate oil level reading is essential: 1.

If the engine has been running recently, turn off the engine and allow several minutes for the oil

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (16,1)

10-16

Vehicle Care

When to Add Engine Oil (Except Z/28)

If the oil is below the cross-hatched area at the tip of the dipstick, add 1 L (1 qt) of the recommended oil and then recheck the level. See “Selecting the Right Engine Oil” in this section for an explanation of what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 12-2.

{ Caution

Do not add too much oil. Oil levels above or below the acceptable operating range shown on the dipstick are harmful (Continued)

Caution (Continued)

to the engine. If you find that you have an oil level above the operating range, i.e., the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged. You should drain out the excess oil or limit driving of the vehicle and seek a service professional to remove the excess amount of oil.

See Engine Compartment Overview on page 10-6 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through.

Checking Engine Oil (Z/28)

1. Engine Oil Dipstick 2. Engine Oil Fill Cap

It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the vehicle must be on level ground. The engine oil dipstick handle is a loop. The dipstick is on the dry sump engine oil tank. See Engine Compartment Overview on page 10-6 for the location of the dry sump engine oil tank.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (17,1)

These vehicles have a dry sump engine lubrication system. This high performance system operates differently than a standard engine lubrication system and requires a special procedure when checking the engine oil level. Follow this procedure closely. The engine oil level must be checked when the engine is warm. Cold oil level in the dry sump tank may not indicate the actual amount of oil in the system. With this system, engine oil is contained in an external tank, separate from the engine. Under normal operating conditions, the oil pan under the engine does not store any oil. If the vehicle has been parked for an extended period without the engine being started, some oil will seep back into the oil pan, reducing the amount of oil held in the dry sump tank and there could be no engine oil at all showing on the dipstick. This is normal since the dipstick is designed to read the engine oil level only after the engine has run long

enough to reach normal operating temperature. Do not add engine oil based on cold engine dipstick readings. The engine oil level on the dipstick will also be inaccurate if checked while the engine is running. 1. To obtain an accurate engine oil

level reading, warm up the engine to at least 80°C (175°F). Cold oil will not give a correct oil level reading.

2. Once the engine is warm, turn off the engine. Checking the oil while the engine is running will result in an incorrect oil level reading.

3. Check the oil level between five and 10 minutes after the engine is shut down.

{ Warning

The engine oil dipstick handle may be hot; it could burn you. Use a towel or glove to touch the dipstick handle.

Vehicle Care

10-17

4. Remove the dipstick from the

external engine oil tank and wipe it with a clean lint-free paper towel or a cloth. Re-insert the dipstick into the external oil tank, pushing it all the way in until it stops.

5. Remove the dipstick from the oil

tank and read the level on the cross-hatched area.

When to Add Engine Oil (Z/28)

If the oil is below the cross-hatched area at the tip of the dipstick, add 1 L (1 qt) of the recommended oil through the oil fill cap opening in the oil tank and then recheck the level. See “Selecting the Right Engine Oil”

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (18,1)

10-18

Vehicle Care

for an explanation of what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 12-2.

{ Caution

Do not add too much oil. Oil levels above or below the acceptable operating range shown on the dipstick are harmful to the engine. If you find that you have an oil level above the operating range, i.e., the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged. You should drain out the excess oil or limit driving of the vehicle and seek a service professional to remove the excess amount of oil.

See Engine Compartment Overview on page 10-6 for the location of the external engine oil tank and fill cap.

Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back into the oil tank when through. Selecting the Right Engine Oil Selecting the right engine oil depends on both the proper oil specification and viscosity grade. See Recommended Fluids and Lubricants on page 11-12.

Specification Ask for and use engine oils that meet the dexos1™ specification. Engine oils that have been approved by GM as meeting the dexos1 specification are marked with the dexos1 approved logo. See www.gmdexos.com. GM recommends Mobil 1® engine oils that show the dexos1 approved logo for its dry sump equipped engines.

{ Caution

Failure to use the recommended engine oil can result in engine damage not covered by the vehicle warranty. Check with your dealer or service provider on whether the oil is approved to the dexos1 specification.

Viscosity Grade Use SAE 5W-30 viscosity grade engine oil. Cold Temperature Operation: In an area of extreme cold, where the temperature falls below −29°C (−20°F), an SAE 0W-30 oil may be used. An oil of this viscosity grade will provide easier cold starting for the engine at extremely low

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (19,1)

temperatures. When selecting an oil of the appropriate viscosity grade, always select an oil of the correct specification. See “Specification” earlier in this section for more information. On Z/28, for track events or competitive driving, use Mobil 1® 15W-50 engine oil. A warning message will display at high oil temperatures. See Engine Oil Messages on page 5-35. Engine Oil Additives/Engine Oil Flushes Do not add anything to the oil. The recommended oils meeting the dexos1 specification are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty.

What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags containing used engine oil. See the manufacturer's warnings about the use and disposal of oil products. Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the filter before disposal. Never dispose of oil by putting it in the trash or pouring it on the ground, into sewers, or into streams or bodies of water. Recycle it by taking it to a place that collects used oil.

Vehicle Care

10-19

Engine Oil Life System

When to Change Engine Oil This vehicle has a computer system that indicates when to change the engine oil and filter. This is based on a combination of factors which include engine revolutions, engine temperature, and miles driven. Based on driving conditions, the mileage at which an oil change is indicated can vary considerably. For the oil life system to work properly, the system must be reset every time the oil is changed. When the system has calculated that oil life has been diminished, it indicates that an oil change is necessary. A CHANGE ENGINE OIL SOON message comes on. See Engine Oil Messages on page 5-35. Change the oil as soon as possible within the next 1 000 km (600 mi). It is possible that, if driving under the best conditions, the oil life system might indicate that an oil change is not necessary for up to a year. The engine oil and filter must

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (20,1)

10-20

Vehicle Care

be changed at least once a year and, at this time, the system must be reset. Your dealer has trained service people who will perform this work and reset the system. It is also important to check the oil regularly over the course of an oil drain interval and keep it at the proper level. If the system is ever reset accidentally, the oil must be changed at 5 000 km (3,000 mi) since the last oil change. Remember to reset the oil life system whenever the oil is changed. How to Reset the Engine Oil Life System Reset the system whenever the engine oil is changed so that the system can calculate the next engine oil change. To reset the system: 1. Display the REMAINING OIL LIFE on the DIC. See Driver Information Center (DIC) on page 5-24.

2. Press and hold the SET/CLR

button on the DIC while the Oil Life display is active. The oil life will change to 100%.

The oil life system can also be reset as follows: 1. Turn the ignition to ON/RUN with

the engine off.

2. Fully press and release the

accelerator pedal three times within five seconds.

The system is reset when the CHANGE ENGINE OIL SOON message goes off. If the CHANGE ENGINE OIL SOON message comes back on when the vehicle is started, the engine oil life system has not been reset. Repeat the procedure.

Automatic Transmission Fluid

How to Check Automatic Transmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to your dealer and have it repaired as soon as possible. The vehicle is not equipped with a transmission fluid level dipstick. There is a special procedure for checking and changing the transmission fluid. Because this procedure is difficult, this should be done at the dealer. Contact the dealer for additional information or the procedure can be found in the service manual. To purchase a service manual, see Service Publications Ordering Information on page 13-11.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (21,1)

Change the fluid and filter at the intervals listed in Maintenance Schedule on page 11-2, and be sure to use the fluid listed in Recommended Fluids and Lubricants on page 11-12.

Manual Transmission Fluid It is not necessary to check the manual transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to your dealer and have it repaired as soon as possible. See Recommended Fluids and Lubricants on page 11-12
for the proper fluid to use.

Hydraulic Clutch For vehicles with a manual transmission, it is not necessary to regularly check brake/clutch fluid unless there is a leak suspected. Adding fluid will not correct a leak.

A fluid loss in this system could indicate a problem. Have the system inspected and repaired. When to Check and What to Use

The brake/hydraulic clutch fluid reservoir cap has this symbol on it. The common hydraulic clutch and brake master cylinder fluid reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. See Engine Compartment Overview on page 10-6 for reservoir location. How to Check and Add Fluid Visually check the brake/clutch fluid reservoir to make sure the fluid level is at the MIN (minimum) line on the side of the reservoir. The brake/ hydraulic clutch fluid system should be closed and sealed.

Vehicle Care

10-21

Do not remove the cap to check the fluid level or to top‐off the fluid level. Remove the cap only when necessary to add the proper fluid until the level reaches the MIN line.

Engine Air Cleaner/Filter (Except ZL1 and Z/28)) See Engine Compartment Overview on page 10-6 for the location of the engine air cleaner/filter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the scheduled maintenance intervals and replace it at the appropriate interval. See Maintenance Schedule on page 11-2 for more information. If driving in dusty/dirty conditions, inspect the filter at each engine oil change.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (22,1)

10-22

Vehicle Care

How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt. If the filter remains covered with dirt, a new filter is required. To inspect or replace the engine air cleaner/filter: 1. Open the hood. See Hood on

page 10-5.

2. Locate the air filter housing on

the front of the driver side of the engine compartment. See Engine Compartment Overview on page 10-6.

3. Loosen the clamp at the duct of

the air cleaner/filter housing.

4. Unlatch the retaining clips on the

air cleaner/filter housing.

5. Lift the cover at the retaining clip location high enough to clear the retaining clips and pull the cover outward to remove it from the air cleaner/filter housing hinges. 6. Pull straight up on the cover;

7.

while holding the cover, remove the air filter. Inspect or replace the air filter. See Maintenance Replacement Parts on page 11-14.

8. Reverse Steps 1–6 to reinstall

the cover.

{ Warning

Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it

(Continued)

3.6L V6 Engine Air Cleaner/Filter Housing Shown (6.2L V8 Engines

Similar)

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (23,1)

Warning (Continued)

helps to stop flames if the engine backfires. Use caution when working on the engine and do not drive with the air cleaner/filter off.

{ Caution

If the air cleaner/filter is off, dirt can easily get into the engine, which could damage it. Always have the air cleaner/filter in place when you are driving.

Engine Air Cleaner/Filter (ZL1 Only) See Engine Compartment Overview on page 10-6 for the location of the engine air cleaner/filter.

{ Caution

If water is sprayed and enters the engine air cleaner/filter intake and housing, the engine could be damaged. The repairs would not be covered by the vehicle warranty.

When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the scheduled maintenance intervals and replace it at the appropriate interval. See Maintenance Schedule on page 11-2 for more information. If driving in dusty/dirty conditions, inspect the filter at each engine oil change. How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release

Vehicle Care

10-23

loose dust and dirt. If the filter remains covered with dirt, a new filter is required. To inspect or replace the engine air cleaner/filter:

1. Air Duct Clamp 2. Screws

1. Open the hood. See Hood on

page 10-5.

2. Disconnect the outlet duct by loosening the screw on the air duct clamp.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (24,1)

10-24

Vehicle Care

3. Remove the two screws

securing the cover on the air cleaner/filter housing.

4. Pull straight up on the cover;

5.

while holding the cover, remove the air filter. Inspect or replace the air filter. See Maintenance Replacement Parts on page 11-14.

6. Reverse Steps 2–5 to reinstall

the cover.

{ Warning

Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. Use caution when working on the engine and do not drive with the air cleaner/filter off.

{ Caution

If the air cleaner/filter is off, dirt can easily get into the engine, which could damage it. Always have the air cleaner/filter in place when you are driving.

Engine Air Cleaner/Filter (Z/28 Only) See Engine Compartment Overview on page 10-6 for the location of the engine air cleaner/filter. { Caution

If water is sprayed and enters the engine air cleaner/filter intake and housing, the engine could be damaged. The repairs would not be covered by the vehicle warranty.

When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the scheduled maintenance intervals and replace it at the appropriate interval. See Maintenance Schedule on page 11-2 for more information. If driving in dusty/dirty conditions, inspect the filter at each engine oil change. How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt. If the filter remains covered with dirt, a new filter is required.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (25,1)

4.

Inspect or replace the air filter. See Maintenance Replacement Parts on page 11-14.

5. Using the same air filter/cleaner clamp (1), install the air cleaner/ filter. Make sure that the air cleaner/filter alignment tabs (2) are set properly, and tighten the screw on the clamp. { Warning

Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. Use caution when working on the engine and do not drive with the air cleaner/filter off.

To inspect or replace the engine air cleaner/filter:

1. Air Cleaner/Filter Clamp 2. Air Cleaner/Filter

Alignment Tabs

1. Open the hood. See Hood on

page 10-5.

2. Loosen the screw on the air

cleaner/filter clamp (1).

3. Remove the filter by moving it outward while tipping it upward from the mass air flow sensor air tube.

Vehicle Care

10-25

{ Caution

If the air cleaner/filter is off, dirt can easily get into the engine, which could damage it. Always have the air cleaner/filter in place when you are driving.

Cooling System (Except ZL1 and Z/28 Engines)

3.6L V6 Engine

1. Engine Coolant Recovery

Bottle

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (26,1)

10-26

Vehicle Care

2. Electric Cooling Fans (Out

of View)

3. Radiator Cap (Under Engine

Cover)

6.2L V8 Engines (L99 Shown, LS3

Similar)

1. Engine Coolant Recovery

Bottle

2. Electric Cooling Fans (Out

of View)

3. Radiator Cap (Out of View)

{ Warning

{ Warning

An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.

If the coolant inside the engine coolant recovery bottle is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface. The coolant level should be between the MIN and MAX lines. If it is not, the vehicle may have a leak at the radiator hoses, heater hoses, radiator, water pump, or somewhere else in the cooling system.

Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle.

If there seems to be no leak, with the engine on, check to see if the electric engine cooling fans are running. If the engine is overheating, the fans should be running. If it is not, the vehicle needs service. Turn off the engine.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (27,1)

Cooling System (ZL1
Engine Only)

{ Caution Using coolant other than DEX-COOL® can cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant could require changing sooner. Any repairs would not be covered by the vehicle warranty. Always use DEX-COOL (silicate-free) coolant in the vehicle.

6.2L V8 Engine

1. Engine Coolant Recovery

Bottle

2. Electric Cooling Fans (Out

of View)

3. Radiator Cap

Vehicle Care

10-27

{ Warning

An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.

If the coolant inside the engine coolant recovery bottle is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface. The coolant level should be between the MIN and MAX lines. If it is not, the vehicle may have a leak at the radiator hoses, heater hoses, radiator, water pump, or somewhere else in the cooling system.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (28,1)

10-28

Vehicle Care

{ Warning

Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle.

If there seems to be no leak, with the engine on, check to see if the electric engine cooling fans are running. If the engine is overheating, the fans should be running. If it is not, the vehicle needs service. Turn off the engine.

{ Caution Using coolant other than DEX-COOL® can cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant could require changing sooner. Any repairs would not be covered by the vehicle warranty. Always use DEX-COOL (silicate-free) coolant in the vehicle.

Cooling System (Intercooler)

Intercooler ZL1 Only The 6.2L LSA supercharged V8 engine has an intercooler cooling system.

1. 2.

Intercooler Fill Cap Intercooler Fill Neck

1. Open the hood and remove the engine cover. See Engine Cover on page 10-13.

2. Turn the intercooler fill neck (2)

to the vertical position. 3. Remove the intercooler

fill cap (1).

4. Check to see if coolant is visible

5.

near the top of the opening. If coolant is not visible, see dealer for service.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (29,1)

Cooling System (Z/28
Engine Only)

6. Reverse Steps 1–3 to install

intercooler fill cap and turn the intercooler fill neck.

The intercooler cooling system has a special procedure for draining and adding coolant. Because this procedure is difficult, see the dealer for service if the intercooler is low on coolant. The procedure can also be found in the service manual. To purchase a service manual, see Service Publications Ordering Information on page 13-11.

7.0L V8 Engine

1. Engine Coolant Recovery

Bottle

2. Electric Cooling Fans (Out

of View)

3. Radiator Cap

Vehicle Care

10-29

{ Warning

An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.

If the coolant inside the engine coolant recovery bottle is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface. The coolant level should be between the MIN and MAX lines. If it is not, the vehicle may have a leak at the radiator hoses, heater hoses, radiator, water pump, or somewhere else in the cooling system.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (30,1)

10-30

Vehicle Care

{ Warning

Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle.

If there seems to be no leak, with the engine on, check to see if the electric engine cooling fans are running. If the engine is overheating, the fans should be running. If it is not, the vehicle needs service. Turn off the engine.

What to Use

{ Warning

Adding only plain water or some other liquid to the cooling system can be dangerous. Plain water and other liquids, can boil before the proper coolant mixture will. The coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned. Use a 50/ 50 mixture of clean, drinkable water and DEX-COOL coolant.

{ Caution Using coolant other than DEX-COOL® can cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant could require changing sooner. Any repairs would not be covered by the vehicle warranty. Always use DEX-COOL (silicate-free) coolant in the vehicle.

Engine Coolant The cooling system in the vehicle is filled with DEX-COOL® engine coolant. This coolant is designed to remain in the vehicle for 5 years or 240 000 km (150,000 mi), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low. If there is a problem with engine overheating, see Engine Overheating on page 10-35.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (31,1)

Vehicle Care

10-31

Check coolant as follows: 1. Turn the ignition off. 2. Locate the engine coolant

recovery bottle. See Engine Compartment Overview on page 10-6.

3. Turn the coolant dipstick cap

counterclockwise and slowly pull out the dipstick.

Use a 50/50 mixture of clean, drinkable water and DEX-COOL coolant. If using this mixture, nothing else needs to be added. This mixture: . Gives freezing protection down

to −37°C (−34°F), outside temperature.

. Gives boiling protection up to

129°C (265°F), engine temperature.

. Protects against rust and

corrosion.

. Will not damage aluminum parts. . Helps keep the proper engine

temperature.

{ Caution

If improper coolant mixture, inhibitors, or additives are used in the vehicle cooling system, the engine could overheat and be damaged. Too much water in the

(Continued)

Caution (Continued)

mixture can freeze and crack engine cooling parts. The repairs would not be covered by the vehicle warranty. Use only the proper mixture of engine coolant for the cooling system. See Recommended Fluids and Lubricants on page 11-12.

Never dispose of engine coolant by putting it in the trash, pouring it on the ground, or into sewers, streams, or bodies of water. Have the coolant changed by an authorized service center, familiar with legal requirements regarding used coolant disposal. This will help protect the environment and your health. Checking Coolant The vehicle must be on a level surface when checking the coolant level.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (32,1)

10-32

Vehicle Care

How to Add Coolant to the Coolant Recovery Bottle

{ Warning

You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.

{ Caution

This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged.

Add coolant as follows: 1. Turn the engine coolant recovery

bottle dipstick cap counterclockwise and slowly pull out the dipstick.

2. Pour the coolant into the engine

coolant recovery bottle.

3. When the level is correct,

replace the dipstick and turn the cap clockwise to secure.

How to Add Coolant to the Radiator

{ Warning

You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.

{ Caution

This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged.

4. There are maximum and

minimum markings on the dipstick. When the engine is cold, the coolant level should be at or above the MIN mark on the dipstick. After the vehicle has been driven and the engine is at normal operating temperature, the level should be somewhere between half full and the maximum mark. If the coolant level is correct, replace the dipstick and turn the cap clockwise to secure.

5.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (33,1)

{ Warning

An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.

{ Warning

Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the surge tank pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the surge tank pressure cap, is hot. Wait for the cooling system and surge tank pressure cap to cool if you ever have to turn the pressure cap.

If coolant is needed, add the proper mixture directly to the radiator, but be sure the cooling system is cool before this is done. If no coolant is visible in the engine coolant recovery bottle, add coolant as follows:

3.6L V6 Engine Fill Procedure 1. Locate the radiator cap. See

Engine Compartment Overview on page 10-6.

2. Remove the engine cover to access the radiator cap. See Engine Cover on page 10-13.

3. Cover the radiator cap with a

thick cloth and turn it slowly counterclockwise and remove.

Vehicle Care

10-33

4.

If there is no coolant visible or the level is low, slowly fill the system through the radiator cap opening with a 50/50 mixture of DEX-COOL and clean drinkable water. Wait 30 seconds for coolant to settle and continue filling if the level drops. Do not spill coolant on the accessory drive belts. If a spill occurs, rinse the belt with fresh water. 5. Start the engine. 6. With the engine idling, continue

to add coolant through the radiator cap opening until full. Wait 30 seconds for the coolant to settle and top off, if the level drops.

7. Once the system is full, put the radiator cap back on by turning clockwise.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (34,1)

10-34

Vehicle Care

8. With the engine still running,

raise the engine to 2500 rpm for 30–40 seconds.

9. Turn the engine off. 10. Repeat Steps 2–7 then turn the

engine off.

11. Allow engine to cool for

45 minutes. Top off coolant through the radiator cap opening and reinstall the radiator cap.

12. Reinstall the engine cover. See

Engine Cover on page 10-13.

13. Check the coolant level in the engine coolant recovery bottle and fill it until the level is at the top symbol on the dipstick.

6.2L V8 and 7.0L V8 Engine Fill Procedure 1. Locate the radiator cap. See

Engine Compartment Overview on page 10-6.

2. Cover the radiator cap with a

thick cloth and turn it slowly counterclockwise and remove.

3.

If there is no coolant visible or the level is low, slowly fill the system through the radiator cap opening with a 50/50 mixture of clean, drinkable water and DEX-COOL coolant until full. Wait 30 seconds for coolant to settle and top off if the level drops. Do not spill coolant on the accessory drive belts. If a spill occurs, rinse the belt with fresh water. 4. Start the engine. 5. With the engine idling, top off the coolant through the radiator cap opening until full. Wait 30 seconds for the coolant to settle and top off, if the level drops.

6. Once the system is full, put the radiator cap back on by turning clockwise.

7. Turn the engine off.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (35,1)

Engine Overheating The vehicle has an indicator to warn of engine overheating. There is an engine coolant temperature gauge on the vehicle instrument panel. See Engine Coolant Temperature Gauge on page 5-12. If the decision is made not to lift the hood when this warning appears, but instead get service help right away. See Roadside Assistance Program on page 13-5. If the decision is made to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced.

Vehicle Care

10-35

{ Caution

Running the engine without coolant may cause damage or a fire. Vehicle damage would not be covered by the vehicle warranty.

If Steam Is Coming from the Engine Compartment { Warning

Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.

(Continued)

8. Check the coolant level in the engine coolant recovery bottle and fill it until the level is at the top mark on the dipstick.

{ Caution

If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (36,1)

10-36

Vehicle Care

Warning (Continued)

If you keep driving when the engine is overheated, the liquids in it can catch fire. You or others could be badly burned. Stop the engine if it overheats, and get out of the vehicle until the engine is cool.

If No Steam Is Coming from the Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: . Climbs a long hill on a hot day. . Stops after high-speed driving. Idles for long periods in traffic. Tows a trailer.

If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest

temperature and to the highest fan speed. Open the windows as necessary.

3. When it is safe to do so, pull off

the road, shift to P (Park) or N (Neutral) and let the engine idle.

If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slowly for about 10 minutes. Keep a safe vehicle distance from the vehicle in front. If the warning does not come back on, continue to drive normally and have the cooling system checked for proper fill and function. If the warning continues, pull over, stop, and park the vehicle right away.

If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down.

Power Steering Fluid (L99, LS3, ZL1 and Z/28) The vehicle has electric power steering and does not use power steering fluid.

Power Steering Fluid (LFX)

The power steering fluid reservoir is under the engine cover on the driver side toward the front of the engine compartment. See Engine Compartment Overview on page 10-6.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (37,1)

When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or an unusual noise is heard. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. How to Check Power Steering Fluid Check the level after the vehicle has been driven for at least 20 minutes so the fluid is warm. To check the power steering fluid: 1. Turn the ignition key to LOCK/

OFF and let the engine compartment cool down.

2. Remove the engine cover. See

Engine Cover on page 10-13.

3. Wipe the cap and the top of the

reservoir clean.

4. Turn the cap counterclockwise

and pull it straight up.

5. Wipe the dipstick with a

clean rag.

6. Replace the cap and completely

tighten it.

7. Remove the cap again and look at the fluid level on the dipstick.

When the engine is hot, the level should be at the hot MAX level. When the engine is cold, the fluid level should be between MIN and MAX on the dipstick.

What to Use To determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 11-12. Always use the proper fluid.

Vehicle Care

10-37

Washer Fluid

What to Use When windshield washer fluid is needed, be sure to read the manufacturer's instructions before use. If operating the vehicle in an area where the temperature can fall below freezing, use a fluid that has sufficient protection against freezing. Adding Washer Fluid

Open the cap with the washer symbol on it. Add washer fluid until the reservoir is full. See Engine Compartment Overview on page 10-6 for reservoir location.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (38,1)

10-38

Vehicle Care

{ Caution

. Do not use engine coolant

(antifreeze) in the windshield washer. It can damage the windshield washer system and paint.

. Do not mix water with

ready-to-use washer fluid. Water can cause the solution to freeze and damage the washer fluid tank and other parts of the washer system.

. When using concentrated

washer fluid, follow the manufacturer instructions for adding water.

. Fill the washer fluid tank only

three-quarters full when it is very cold. This allows for fluid expansion if freezing occurs, which could damage the tank if it is completely full.

Brakes Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time when the vehicle is moving, except when applying the brake pedal firmly.

{ Warning

The brake wear warning sound means that soon the brakes will not work well. That could lead to a crash. When the brake wear warning sound is heard, have the vehicle serviced.

{ Caution

Continuing to drive with worn-out brake pads could result in costly brake repair.

Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with the brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications. See Capacities and Specifications on page 12-2. Brake pads should be replaced as complete sets. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service may be required. Replacing Brake System Parts Always replace brake system parts with new, approved replacement parts. If this is not done, the brakes may not work properly. The braking

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (39,1)

performance expected can change in many other ways if the wrong replacement brake parts are installed or parts are improperly installed. Z/28 Brake Pad and Rotor Wear The Z/28 has electronic brake pad wear sensors. When the pads are worn, a message displays in the Driver Information Center. See Brake System Messages on page 5-33.

Visual Inspection Periodic visual inspection of the brake pads is required to determine when to replace the brake pads. . Brake pads can be visually

inspected through the wheel by inspecting the outer brake pads at each wheel.

. Brake pads should be replaced

when the pad lining is worn to 2 mm of pad thickness. New pads are 10 mm thick.

In addition, brake pad inspection is required any time the tires are removed.

The Z/28 has ceramic brake rotors. Rotors should be visually inspected when the brake pads are replaced. The rotor can be reused if it is within specification. Rotor inspection and measuring methods can be found in the service manual. See Service Publications Ordering Information on page 13-11.

Brake Fluid

The brake/clutch master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. See Engine Compartment Overview on page 10-6 for the location of the reservoir.

Vehicle Care

10-39

There are only two reasons why the fluid level in the reservoir might go down:

The fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up.

. A fluid leak in the brake/clutch

hydraulic system can also cause a low fluid level. Have the brake/ clutch hydraulic system fixed, since a leak means that sooner or later the brakes and/or clutch will not work well.

Do not top off the brake/clutch fluid. Adding fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as necessary, only when work is done on the brake/clutch hydraulic system.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (40,1)

10-40

Vehicle Care

{ Warning

{ Warning

If too much brake fluid is added, it can spill on the engine and burn, if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake fluid only when work is done on the brake/clutch hydraulic system.

When the brake/clutch fluid falls to a low level, the brake warning light comes on. See Brake System Warning Light on page 5-19.

What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 11-12. Always clean the brake/clutch fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.

With the wrong kind of fluid in the brake/clutch hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake/clutch fluid.

{ Caution

. Using the wrong fluid can

badly damage brake/clutch hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid.

(Continued)

Caution (Continued)

. If brake fluid is spilled on the

vehicle's painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle. If you do, wash it off immediately.

Battery The original equipment battery is maintenance free. Do not remove the cap and do not add fluid. The battery is in the trunk, under the floor panel. Refer to the replacement number shown on the original battery label when a new battery is needed.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (41,1)

{ Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Vehicle Storage

{ Warning

Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 10-95 for tips on working around a battery without getting hurt.

Infrequent Usage: Remove the black, negative (−) cable from the battery to keep the battery from running down.

Extended Storage: Remove the black, negative (−) cable from the battery or use a battery trickle charger.

Rear Axle

When to Check Lubricant It is not necessary to regularly check the rear axle fluid, unless a leak is suspected or an unusual noise is heard. A fluid loss could indicate a problem. Have it inspected and repaired by your dealer.

Starter Switch Check

{ Warning When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

Vehicle Care

10-41

1. Before starting this check, be

sure there is enough room around the vehicle.

2. Apply both the parking brake

and the regular brake. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.

3. For automatic transmission

vehicles, try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service. For manual transmission vehicles, put the shift lever in Neutral, push the clutch pedal down halfway, and try to start the engine. The vehicle should start only when the clutch pedal is pushed down all the way to the floor. If the vehicle starts when the clutch pedal is not pushed all the way down, contact your dealer for service.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (42,1)

10-42

Vehicle Care

Automatic Transmission Shift Lock Control Function Check

{ Warning When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

1. Before starting this check, be

sure there is enough room around the vehicle. It should be parked on a level surface.

2. Apply the parking brake. Be

ready to apply the regular brake immediately if the vehicle begins to move.

3. With the engine off, turn the

ignition on, but do not start the engine. Without applying the regular brake, try to move the shift lever out of P (Park) with

normal effort. If the shift lever moves out of P (Park), contact your dealer for service.

Ignition Transmission Lock Check While parked and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position.

The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). The ignition key should come out only in LOCK/OFF.

Contact your dealer if service is required.

Park Brake and P (Park) Mechanism Check { Warning

When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.

Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.

To check the parking brake's holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (43,1)

Vehicle Care

10-43

warranty. Do not allow the wiper blade arm to touch the windshield.

5. Reverse Steps 1–3 for wiper

blade replacement.

Windshield Replacement If the Head-Up display (HUD) system and the windshield need to be replaced, get one that is designed for HUD or the HUD image may look out of focus.

To check the P (Park) mechanism's holding ability: With the engine running, shift to P (Park). Then release the parking brake followed by the regular brake.

Contact your dealer if service is required.

Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking. See Maintenance Schedule on page 11-2 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Maintenance Replacement Parts on page 11-14. To replace the windshield wiper blade: 1. Pull the windshield wiper assembly away from the windshield.

2. Lift up on the latch in the middle

of the wiper blade where the wiper arm attaches.

3. With the latch open, pull the wiper blade down toward the windshield far enough to release it from the J-hooked end of the wiper arm.

4. Remove the wiper blade.

Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not be covered by the vehicle

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (44,1)

10-44

Vehicle Care

Headlamp Aiming Headlamp aim has been preset and should need no further adjustment. If the vehicle is damaged in a crash, the headlamp aim may be affected. If adjustment to the headlamps is necessary, see your dealer.

Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 10-47. For any bulb‐changing procedure not listed in this section, contact your dealer.

Halogen Bulbs

{ Warning

Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.

High Intensity Discharge (HID) Lighting

{ Warning

The high intensity discharge lighting system operates at a very high voltage. If you try to service any of the system components, you could be seriously injured. Have your dealer or a qualified technician service them.

After an HID headlamp bulb has been replaced, the beam might be a slightly different shade than it was originally. This is normal.

Headlamps, Front Turn Signal and Parking Lamps (Uplevel Vehicle) The uplevel model vehicle has an HID headlamp and a turn signal lamp on the headlamp assembly. The parking lamp is also the

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (45,1)

Vehicle Care

10-45

7. Pull the duct back out of the air

cleaner/filter housing until the tabs snap the duct back into position.

Headlamps, Front Turn Signal and Parking Lamps (Base Vehicle) The base model vehicle has a halogen headlamp and a turn signal/parking lamp on the headlamp assembly. To replace one of these bulbs: 1. Open the hood. See Hood on

page 10-5.

function of the HID headlamp. See High Intensity Discharge (HID) Lighting on page 10-44. To replace the turn signal bulb: 1. Open the hood. See Hood on

page 10-5.

3. Disconnect the wiring harness

and turn the bulb socket counterclockwise to remove it from the headlamp assembly. 4. Pull the bulb straight out from

the socket.

5. Push the new bulb into the

socket and reinstall the socket into the headlamp assembly by turning it clockwise.

6. Reconnect the electrical

connector.

2. Press in on the tabs on the sides

of the duct, and then push the duct rearward into the air cleaner/filter housing.

Chevrolet Camaro Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 7695163) - 2015 - crc - 9/4/14

Black plate (46,1)

10-46

Vehicle Care

6. Reconnect the electrical

connector.

7. Pull the duct back out of the air

cleaner/filter housing until the tabs snap the duct back into position.

Taillamps, Turn Signal, and Stoplamps To replace a taillamp, turn signal, or stoplamp bulb: 1. Open the trunk. See Trunk on

page 2-10.