Download PDF Manual


332


Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (11⁄2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. Traction — AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.


Temperature — A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment may need to be checked. If you notice your vehicle vibrating when driving on a smooth road, your tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.


Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know the kind of wheel you need.


333


Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts, or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, and wheel nuts for your vehicle.


Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See Changing a Flat Tire on page 336 for more information. Used Replacement Wheels


{CAUTION:


{CAUTION:


Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.


Putting a used wheel on your vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.


334


Tire Chains Notice: Use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires. Install them on the front tires and tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.


If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop well out of the traffic lane.


A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop, well off the road if possible.


{CAUTION:


Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. Use the jack provided with your vehicle only for changing a flat tire.


If a tire goes flat, the next part shows how to use the jacking equipment to change a flat tire safely.


335


Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers.


{CAUTION:


Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving:


1. Set the parking brake firmly. 2. Put an automatic transaxle shift lever


in PARK (P), or shift a manual transaxle to FIRST (1) or REVERSE (R). (Continued)


CAUTION:


CAUTION:


(Continued)


3. Turn off the engine and do not restart


while the vehicle is raised.


4. Do not allow passengers to remain in


the vehicle.


To be even more certain the vehicle will not move, you should put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire on the other side, at the opposite end of the vehicle.


When you have a flat tire, use the following example as a guide to assist you in the placement of wheel blocks.


336


The following information will tell you how to use the jack and change a tire.


Removing the Spare Tire and Tools The compact spare tire and tools you will need are located in the trunk.


A. Jack B. Wheel Wrench


C. Jack Handle D. Screwdriver


337


1. Open the trunk or liftgate. See Trunk on


page 98 or Liftgate (Hatchback) on page 100
for more information.


2. Lift the trim cover.


3. Remove the foam tray. 4. Remove the jack, the jack handle and the


wheel wrench from the foam tray.


338


5. Turn the retainer counterclockwise and


remove it from the compact spare.


6. Remove the compact spare tire. See Compact Spare Tire on page 344 for more information.


Removing the Flat Tire and Installing the Spare Tire 1. If your vehicle has wheel covers, loosen the


four plastic caps by hand or by using the wheel wrench. The plastic nuts do not come off of the cover.


2. Remove the wheel cover using the flat end of


the jack handle. Pry along the edge of the wheel cover until it comes off.


Hatchback


3. Use the wheel wrench to loosen all the wheel


nuts. Do not remove them yet.


339


Sedan


4. Locate the notch in the frame near each


wheel which the jack head fits in.


5. Position the jack and raise the jack head until


it fits firmly into the notch in the vehicle’s frame nearest the flat tire.


6. Put the compact spare tire near you.


7. Insert the jack handle into the jack and the


wheel wrench onto the end of the jack handle.


340


{CAUTION:


{CAUTION:


Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.


Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.


8. Raise the vehicle by turning the wheel wrench


clockwise. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to fit underneath the wheel well.


9. Remove all of the wheel nuts by turning them


counterclockwise.


10. Remove the flat tire.


341


{CAUTION:


Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off.


11. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel.


12. Place the compact spare tire on the


wheel-mounting surface.


{CAUTION:


Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident.


342


13. Install the wheel nuts with the rounded end of


the nuts toward the wheel. Tighten each nut by hand clockwise until the wheel is held against the hub.


14. Lower the vehicle by turning the wheel


wrench counterclockwise. Lower the jack completely.


{CAUTION:


Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification. See Capacities and Specifications on page 368
for wheel nut torque specification.


Improperly tightened wheel nuts can


Notice: lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 368 for the wheel nut torque specification.


15. Tighten the wheel


nuts firmly in a crisscross sequence, as shown.


Notice: Wheel covers will not fit on your compact spare. If you try to put a wheel cover on the compact spare, you could damage the cover or the spare. Do not try to put a wheel cover on your compact spare tire. It will not fit. Store the wheel cover in the cargo area until you have the flat tire repaired or replaced.


343


Storing a Flat or Spare Tire and Tools


{CAUTION:


Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.


To store a flat or compact spare tire and tools, do the following: 1. Store the flat tire or the compact spare in the


compact spare tire compartment.


2. Secure the retainer. 3. Store the tools securely in the foam tray and


place the tray back in the cargo area.


4. Replace the trim cover. The compact spare tire is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can. See Compact Spare Tire on page 344.


344


Compact Spare Tire Although the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inflated. The compact spare is made to perform well at speeds up to 50 mph (80 km/h), so you can finish your trip and have your full-size tire repaired or replaced where you want. Of course, it is best to replace your spare with a full-size tire as soon as you can. Your spare will last longer and be in good shape in case you need it again. Notice: When the compact spare is installed, do not take your vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails. That can damage the tire and wheel, and maybe other parts of your vehicle.


Do not use your compact spare on other vehicles. And do not mix your compact spare tire or wheel with other wheels or tires. They will not fit. Keep your spare tire and its wheel together. Notice: Tire chains will not fit your compact spare. Using them can damage your vehicle and can damage the chains too. Do not use tire chains on your compact spare. Appearance Care


Cleaning the Inside of Your Vehicle Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery. It is important to keep your upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible. Your vehicle’s interior may experience extremes of heat that could cause stains to set rapidly.


Lighter colored interiors may require more frequent cleaning. Use care because newspapers and garments that transfer color to your home furnishings may also transfer color to your vehicle’s interior. When cleaning your vehicle’s interior, only use cleaners specifically designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately. To prevent over-spray, apply cleaner directly to the cleaning cloth. Notice: cleaning glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the rear window defogger. When cleaning the glass on your vehicle, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in your vehicle’s breathing space. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning your vehicle’s interior, maintain adequate ventilation by opening your vehicle’s doors and windows.


If you use abrasive cleaners when


345


Dust may be removed from small buttons and knobs using a small brush with soft bristles. Your GM dealer has a product for cleaning your vehicle’s glass. Should it become necessary, you can also obtain a product from your GM dealer to remove odors from your vehicle’s upholstery. Do not clean your vehicle using the following cleaners or techniques: • Never use a knife or any other sharp object to


remove a soil from any interior surface.


• Never use a stiff brush. It can cause damage


to your vehicle’s interior surfaces. • Never apply heavy pressure or rub


aggressively with a cleaning cloth. Use of heavy pressure can damage your interior and does not improve the effectiveness of soil removal.


• Use only mild, neutral-pH soaps. Avoid


laundry detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide.


346


• Do not heavily saturate your upholstery while


cleaning.


• Damage to your vehicle’s interior may result from the use of many organic solvents such as naptha, alcohol, etc.


Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda. Before cleaning, gently remove as much of the soil as possible using one of the following techniques: • For liquids: gently blot the remaining soil


with a paper towel. Allow the soil to absorb into the paper towel until no more can be removed.


• For solid dry soils: remove as much as


possible and then vacuum.


Leather A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather. Never use spot lifters or spot removers on leather. Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of your leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Never use shoe polish on your leather.


To clean, use the following instructions: 1. Saturate a lint-free, clean white cloth with


water or club soda.


2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently


rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.


4. Continue to gently rub the soiled area until the


cleaning cloth remains clean.


5. If the soil is not completely removed, use a mild soap solution and repeat the cleaning process that was used with plain water.


If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. After the cleaning process has been completed, a paper towel can be used to blot excess moisture from the fabric or carpet.


347


Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of your interior and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Some commercial products may increase gloss on your instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions.


Care of Safety Belts Keep belts clean and dry.


{CAUTION:


Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.


Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required.


348


Washing Your Vehicle The paint finish on the vehicle provides beauty, depth of color, gloss retention, and durability. The best way to preserve the vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Do not wash the vehicle in the direct rays of the sun. Use a car washing soap. Do not use strong soaps or chemical detergents. Be sure to rinse the vehicle well, removing all soap residue completely. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 353. Do not use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle.


Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 349.


Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 353. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle. The vehicle has a basecoat/clearcoat paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish.


349


Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather, and chemical fallout that can take their toll over a period of years. To help keep the paint finish looking new, keep the vehicle in a garage or covered whenever possible.


Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap, or other material may be on the blade or windshield. Clean the outside of the windshield with a glass cleaning liquid or powder and water solution. The windshield is clean if beads do not form when it is rinsed with water.


Grime from the windshield will stick to the wiper blades and affect their performance. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Check the wiper blades and clean them as necessary; replace blades that look worn.


If you use strong soaps, chemicals,


Aluminum Wheels Notice: abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by your warranty. Use only GM-approved cleaners on aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.


350


Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only. The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged. Do not use chrome polish on aluminum wheels. Notice: If you drive your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum or chrome-plated wheels. The repairs would not be covered by your warranty. Never drive a vehicle equipped with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes. Do not take the vehicle through an automatic car wash that has silicone carbide tire cleaning brushes. These brushes can also damage the surface of these wheels.


Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.


Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.


351


Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your GM dealer. Larger areas of finish damage can be corrected in your GM dealer’s body and paint shop.


Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection.


At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this for you.


Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, GM will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.


352


Vehicle Care/Appearance Materials


Description


Usage


Description


Usage


Polishing Cloth Wax-Treated


Tar and Road Oil Remover


Interior and exterior polishing cloth.


Removes tar, road oil and asphalt.


Chrome Cleaner and Polish


Use on chrome or stainless steel.


White Sidewall Tire Cleaner


Removes soil and black marks from whitewalls.


Vinyl Cleaner


Glass Cleaner


Chrome and Wire Wheel Cleaner


Finish Enhancer


Cleans vinyl.


Removes dirt, grime, smoke and fingerprints.


Removes dirt and grime from chrome wheels and wire wheel covers.


Removes dust, fingerprints, and surface contaminants. Spray on wipe off.


Swirl Remover Polish


Cleaner Wax


Foaming Tire Shine Low Gloss


Wash Wax Concentrate


Spot Lifter


Odor Eliminator


Removes swirl marks, fine scratches and other light surface contamination.


Removes light scratches and protects finish.


Cleans, shines and protects in one easy step, no wiping necessary.


Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free.


Quickly and easily removes spots and stains from carpets, vinyl and cloth upholstery.


Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet.


353


Vehicle Identification


Vehicle Identification Number (VIN)


This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration.


Engine Identification The eighth character in your VIN is the engine code. This code will help you identify your engine, specifications and replacement parts.


Service Parts Identification Label You will find this label on the inside of the glove box. It is very helpful if you ever need to order parts. On this label, you will find the following: • VIN • Model designation • Paint information • Production options and special equipment Do not remove this label from the vehicle.


354


Electrical System


Add-On Electrical Equipment Notice: Do not add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain your vehicle’s battery, even if your vehicle is not operating. Your vehicle has an airbag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Airbag-Equipped Vehicle on page 82.


Headlamp Wiring The headlamp wiring is protected by fuses, one for each headlamp, in the fuse block. An electrical overload will cause the lamps to turn off. If this happens, have your headlamp wiring checked right away.


Windshield Wiper Fuses The windshield wiper motor is protected by an internal circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem and not snow, etc., be sure to get it fixed.


355


Power Windows and Other Power Options Circuit breakers in the fuse block protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away.


Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links in the wiring itself. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating.


There are spare fuses provided in the engine compartment fuse block. If you ever have a problem on the road and do not have a spare fuse, you can borrow one that has the same amperage. Just pick a feature of your vehicle that you can get along without — like the radio or cigarette lighter — and use its fuse, if it is the correct amperage. Replace it as soon as you can. There are two fuse blocks in your vehicle: the instrument panel fuse block and the engine compartment fuse block. There is a fuse puller located on the engine compartment fuse block. It can be used to easily remove fuses from the fuse block.


356


Instrument Panel Fuse Block The instrument panel fuse block is located on the end of the instrument panel on the driver’s side of the vehicle.


Hatchback


Sedan


To access the fuses, open the fuse panel door by pulling the door out. To reinstall the door, first insert the rear edge of the fuse panel door, then push the front of the door into the end of the instrument panel to secure it.


357


Fuses


Usage


AUX LTR


Auxiliary Cigarette Lighter


HORN,


REAR/FOG


Horn, Rear Fog Lamps


LTR


STOP


Cigarette Lighter


Stop Lamp


RADIO, CLK


Audio, Clock


CLSTR, HAZRD


Instrument Panel Cluster, Hazard Flasher


TRN/SIG


Turn Signal


DR/LCK


Door Lock, Remote Keyless Entry


CLSTR, CLK


Instrument Panel Cluster, Clock


ECM, TCM


Engine Control Module (ECM), Transaxle Control Module (TCM)


BCK/UP


Back-Up Lamp


WPR, WSWA Wiper, Washer


ECM, TCM


Engine Control Module (ECM), Transmission Control Module (TCM)


ENG FUSE


Engine Fuse


ALTERNATOR Alternator


Hatchback


358


Fuses


HVAC


Usage


HVAC Blower


AIRBAG 1


Airbag 1


BLANK


Not Used


ABS


Anti-lock Brake System


DIODE (ABS) Anti-lock Brake System Diode


AIRBAG 2


Airbag 2


BLANK


Not Used


CLK, RADIO Clock, Audio


Fuses


SDM


WIPER


Sedan


Usage


Sensing and Diagnostic Module


Windshield Wiper Switch, Windshield Wiper Motor


CLUSTER


Instrument Panel Cluster, Brake Switch, Anti-theft Mode


T/SIG


EMS2


Turn Signal, Hazard Switch


Stoplamp Switch


359


Usage


Fuses


Usage


Fuses


EMS1


Engine Room Fuse Block, Rear HO2S, Transaxle Control Module, VSS, Fuel Pump


STOP LAMP


Brake Switch


CIGAR


Cigarette Lighter, Auxiliary Power Outlet


AUDIO/CLOCK Radio, Clock


OBD


On-Board Diagnostics, Immobilizer ROOM LAMP Trunk Lamp, Trunk Open Switch,


Cluster, Dome Lamp


DOOR LOCK Door Lock/Unlock


B/UP LAMP


Back-up Lamps


HORN


Horn


ELEC MIRROR Mirror Control Switch, Dome Lamp,


Air Conditioning Switch


AUDIO/RKE


Radio, Remote Keyless Entry, Clock, Power Mirror Unit, Anti-Theft Module


DEFOG MIRROR


Power Mirror Unit, Air Conditioning Switch


DEFOGGER Rear Defogger


SUNROOF


Sunroof Module (Option)


DRL


Daytime Running Lamps


BLANK


BLANK


BLANK


Not Used


Not Used


Not Used


360


Engine Compartment Fuse Block The engine compartment fuse block is located on the driver’s side of the vehicle, near the battery. See Engine Compartment Overview on page 276
for more information on location.


Sedan


To access the fuses, pull out the top and bottom flaps to release the cover. To reinstall the cover, push the cover until it is secure.


Hatchback


361


Hatchback


Fuses


Usage


Fuses


Usage


HI BEAM RT


Passenger’s Side Headlamp High


HI BEAM LT


Driver’s Side Headlamp High


DIODE (FOG) Fog Lamp Diode


BLANK


Not Used


362


Fuses


Usage


LOW BEAM RT Passenger’s Side Headlamp Low


Fuses


A/C


Usage


Air Conditioning Compressor


ILLUM RT


Parking Lamp Right Side, Illumination Circuit


LOW BEAM LT Driver’s Side Headlamp Low


FOG LAMPS


Front Fog Lamp


HVAC


BLOWER


Heating, Ventilation, Air Conditioning Blower


ILLUM LT


Driver’s Side Parking Lamp, License Plate Lamp


INT LTS


Room Lamp


BLANK


DEFOG


Not Used


Defogger


S/ROOF


Sunroof


ILLUM LAMPS Illumination Relay


HORN


Horn


HEAD LAMPS Headlamps


FUEL


Fuel Pump


ABS


Anti-lock Brake System


I/P FUSE


BATT.


Instrument Panel Fuse Box


COOL FAN


Radiator Fan


IGN 2


BLANK


IGN 1


Ignition 2


Blank


Ignition 1


PWR WNDW Power Windows


SPARE


Spare


363


Relays


BLANK


COOL


FAN LOW


HEAD


LAMPS HI


Usage


Not Used


Cooling Fan Low


Headlamp High


HEAD LAMPS


LOW


Headlamp Low


PWR WNDW Power Window


FRT FOG


Fog Lamp


Relays


COOL FN


CNTRL


Usage


Cooling Fan Control


FUEL PUMP


Fuel Pump


A/C COMPRSR Air Conditioning Compressor


COOL FAN HI Cooling Fan High


ILLUM LAMPS Illumination Lamps


BLANK


Not Used


364


Sedan


Fuses


BATT


PK/LP LH


Usage


Instrument Panel Fuse Block


Driver’s Side Parking Lamp, Taillamp


Fuses


PK/LP RH


Usage


Passenger’s Side Parking Lamp, Taillamp


IGN2/ST


Ignition Switch


365


Fuses


Usage


ACC/IGN1


Ignition Switch


HAZARD


Hazard Lamps, Theft-Deterrent System


H/L LOW RH Passenger’s Side Low-Beam


Headlamp


FAN HI


Cooling Fan High Speed


H/L LOW LH Driver’s Side Low-Beam Headlamp


Fuses


SPARE


ABS


EMS2


Usage


Spare


Anti-lock Brake System (Option)


LEGR Valve, HO2S, EVAP Canister Purge Solenoid, CMP Sensor


P/WINDOW1


Power Window Switch (Option)


ECU


Engine Control Module, Transaxle Control Module


FRT FOG


Front Fog Lamps (Option)


SPARE


Spare


FAN LOW


Cooling Fan Low Speed


H/L HI


High-Beam Headlamps


A/C COMP


Air Conditioning Compressor (Option)


FUEL PUMP


Fuel Pump


EMS1


Engine Control Module, Injector, Cooling Fan, Air Conditioning Compressor


SPARE


Spare


366


Usage


Relays


Usage


Relays


H/L LOW RELAY


Low-Beam Headlamp Relay


FAN HI RELAY Cooling Fan High Speed Relay


FUEL PUMP


RELAY


P/WINDOW


RELAY


PARK LAMP


RELAY


FRT FOG


RELAY


Fuel Pump Relay


Power Window Relay


Parking Lamp Relay


Front Fog Lamps Relay


H/L HI RELAY High-Beam Headlamp Relay


FAN LOW


RELAY


Cooling Fan Low Speed Relay


A/C RELAY


Air Conditioning Relay (Option)


MAIN RELAY Main Relay


Misc.


Usage


FUSE PULLER Fuse Puller


367


Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Part D: Recommended Fluids and Lubricants on page 396 for more information.


Application


Capacities


English


Metric


Air Conditioning Refrigerant R134a


Cooling System


Engine Oil with Filter


Fuel Tank


Transaxle, Automatic


Transaxle, Manual


For the air conditioning system refrigerant charge amount, see the refrigerant caution label located


under the hood. See your dealer for more


information.


6.3 qt


3.96 qt


11.9 gal


6.2 qt


1.9 qt


6.0 L


3.75 L


45.0 L


5.87 L


1.8 L


Wheel Nut Torque


110 Y All capacities are approximate. When adding, be sure to fill to the appropriate level, as recommended in this manual. Recheck fluid level after filling.


81 lb ft


Engine Specifications


Engine


VIN Code


Transaxle


Spark Plug Gap


1.6L L4 (L91)


Automatic and


Manual


0.039-0.043 inch (1.0-1.1 mm)


368


Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer.


Normal Maintenance Replacement Parts


Part


Passenger Compartment Filter Engine Air Cleaner/Filter Engine Oil Filter Fuel Filter Spark Plugs Windshield Wiper Blade- Hatchback


Driver’s Side Passenger’s Side Rear


Windshield Wiper Blade- Sedan


Driver’s Side Passenger’s Side


1NGK


GM Part Number


96539649
96536694


96458873/96395221


96537170
96130723


96497155
96619022
96301840


96648556



96648561


ACDelco® Part


Number


— — — —


IFR6E111


— — —



369


Engine Drive Belt Routing 1.6L L4 Engine


370


Section 6


Maintenance Schedule


Maintenance Schedule ................................ 372
Introduction ............................................... 372
Maintenance Requirements ........................ 372
Your Vehicle and the Environment ............ 372
How This Section is Organized ................. 373
Part A: Scheduled Maintenance Services .... 374
Using the Maintenance Schedule ............... 374
Selecting the Right Schedule ..................... 375
Short Trip/City Scheduled Maintenance ..... 377
Long Trip/Highway Scheduled


Maintenance .......................................... 384
Part B: Owner Checks and Services ......... 389
At Each Fuel Fill ....................................... 389


At Least Once a Month ............................. 389
At Least Twice a Year .............................. 389
At Least Once a Year ............................... 390
Part C: Periodic Maintenance Inspections .... 394
Steering, Suspension and Front Drive


Axle Boot and Seal Inspection ............... 394
Exhaust System Inspection ........................ 394
Fuel System Inspection ............................. 395
Engine Cooling System Inspection ............. 395
Brake System Inspection ........................... 395
Part D: Recommended Fluids


and Lubricants ....................................... 396
Part E: Maintenance Record ...................... 398


371


Maintenance Schedule


Introduction Important: Keep engine oil at the proper level and change as recommended.


Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details.


Maintenance Requirements Maintenance intervals, checks, inspections and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance may not be covered by warranty.


Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.


372


How This Section is Organized This maintenance schedule is divided into five parts: “Part A: Scheduled Maintenance Services” explains what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your GM dealer’s service department do these jobs. Your GM dealer has GM-trained and supported service people that will perform the work using genuine GM parts.


{CAUTION:


Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, have a qualified technician do the work. See Doing Your Own Service Work on page 265.


If you want to purchase service information, see Service Publications Ordering Information on page 421. “Part B: Owner Checks and Services” tells you what should be checked and when. It also explains what you can easily do to help keep your vehicle in good condition. “Part C: Periodic Maintenance Inspections” explains important inspections that your dealer’s service department can perform for you. “Part D: Recommended Fluids and Lubricants” lists some recommended products necessary to help keep your vehicle properly maintained. These products, or their equivalents, should be used whether you do the work yourself or have it done. “Part E: Maintenance Record” is a place for you to record and keep track of the maintenance performed on your vehicle. Keep your maintenance receipts. They may be needed to qualify your vehicle for warranty repairs.


373


Part A: Scheduled Maintenance Services In this part are scheduled maintenance services which are to be performed at the mileage intervals specified.


Using the Maintenance Schedule We at General Motors want to keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands, or in many other ways. Because of the different ways people use their vehicles, maintenance needs may vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have questions on how to keep your vehicle in good condition, see your dealer.


This part tells you the maintenance services you should have done and when to schedule them. When you go to your dealer for your service needs, you will know that GM-trained and supported service people will perform the work using genuine GM parts. The proper fluids and lubricants to use are listed in Part D. Make sure whoever services your vehicle uses these. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. These schedules are for vehicles that: • carry passengers and cargo within


recommended limits. You will find these on the Tire and Loading Information label. See Loading Your Vehicle on page 248.


• are driven on reasonable road surfaces within


legal driving limits.


• use the recommended fuel. See Gasoline


Octane on page 266.


374


Selecting the Right Schedule First you will need to decide which of the two schedules is right for your vehicle. Here is how to decide which schedule to follow: Short Trip/City Definition Follow the Short Trip/City Scheduled Maintenance if any one of these conditions is true for your vehicle: • Most trips are less than 5 miles (8 km). This is


particularly important when outside temperatures are below freezing.


• Most trips include extensive idling, such as



frequent driving in stop-and-go traffic. If the vehicle is used for delivery service, police, taxi, or other commercial application.


One of the reasons you should follow this schedule if you operate your vehicle under any of these conditions is that these conditions cause engine oil to break down sooner.


Short Trip/City Intervals Every 3,000 Miles (5 000 km): Engine Oil and Filter Change (or 3 months, whichever occurs first). Every 6,000 Miles (10 000 km): Tire Rotation. Every 15,000 Miles (25 000 km): Engine Air Cleaner Filter Inspection. Passenger Compartment Air Filter Replacement. Drive Belt(s) Inspection. Every 30,000 Miles (50 000 km): Engine Air Cleaner Filter Replacement. Spark Plug Replacement. EVAP System Service. PCV System Service. Timing Belt Inspection. Brake/Clutch Fluid Change (or 24 months, whichever occurs first). Every 42,000 Miles (70 000 km): Engine Oil Pan Drain Plug Washer Replacement. Every 60,000 Miles (100 000 km): Spark Plug Wire Replacement. Timing Belt Replacement. EVAP System Solenoid Valve Replacement. Every 90,000 Miles (150 000 km): Fuel Filter Replacement. Every 150,000 Miles (240 000 km): Cooling System Service. These intervals only summarize maintenance services. Be sure to follow the complete scheduled maintenance on the following pages.


375


Long Trip/Highway Definition Follow this scheduled maintenance only if none of the conditions from the Short Trip/City Scheduled Maintenance are true. Do not use this schedule if the vehicle is driven in a dusty area or used off paved roads. Use the Short Trip/City schedule for these conditions. Driving a vehicle with a fully warmed engine under highway conditions will cause engine oil to break down slower. Long Trip/Highway Intervals


Every 7,500 Miles (12 500 km): Engine Oil and Filter Change (or every 12 months, whichever occurs first). Tire Rotation.


Every 15,000 Miles (25 000 km): Engine Air Cleaner Filter Inspection. Passenger Compartment Air Filter Replacement. Drive Belt(s) Inspection.


Every 30,000 Miles (50 000 km): Engine Air Cleaner Filter Replacement. Spark Plug Replacement. EVAP System Service. PCV System Service. Timing Belt Inspection. Brake/Clutch Fluid Change (or 24 months, whichever occurs first).


Every 60,000 Miles (100 000 km): Spark Plug Wire Replacement. Timing Belt Replacement. EVAP System Solenoid Valve Replacement.


Every 90,000 Miles (150 000 km): Fuel Filter Replacement. Engine Oil Pan Drain Plug Washer Replacement.


Every 150,000 Miles (240 000 km): Cooling System Service. These intervals only summarize maintenance services. Be sure to follow the complete scheduled maintenance on the following pages.


376


Short Trip/City Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life of this vehicle. The services shown at 150,000 miles (240 000 km) should be repeated at the same interval after 150,000 miles (240 000 km) for the life of this vehicle. See Part B: Owner Checks and Services on page 389 and Part C: Periodic Maintenance Inspections on page 394. Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded. + A good time to check your brakes is during tire rotation. See Brake System Inspection on page 395.


3,000 Miles (5 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


6,000 Miles (10 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


9,000 Miles (15 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


12,000 Miles (20 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


377


21,000 Miles (35 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


24,000 Miles (40 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +)


27,000 Miles (45 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


15,000 Miles (25 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Replace passenger compartment air filter. If


you drive regularly under dusty conditions, the filter may require replacement more often. Inspect engine air cleaner filter. If necessary, replace the filter. If vehicle is driven in dusty/dirty conditions, inspect filter at every engine oil change. See Engine Air Cleaner/Filter on page 281 for more information. Inspect drive belt(s).


18,000 Miles (30 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


378


❑ ❑ 30,000 Miles (50 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Replace passenger compartment air filter. If


you drive regularly under dusty conditions, the filter may require replacement more often.


❑ Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 281 for more information.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


❑ Replace spark plugs. An Emission Control


Service. Inspect drive belt(s). Inspect timing belt. Inspect EVAP canister, vapor lines, and EVAP vent solenoid valve. An Emission Control Service. (See footnote †.) Inspect PCV system. An Emission Control Service. (See footnote †.)


❑ Change brake/clutch fluid (or every 24 months,


whichever occurs first).


33,000 Miles (55 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


36,000 Miles (60 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


39,000 Miles (65 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


42,000 Miles (70 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Replace engine oil pan drain plug washer. ❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


379


❑ ❑ ❑ ❑ 51,000 Miles (85 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


54,000 Miles (90 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


57,000 Miles (95 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


45,000 Miles (75 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Replace passenger compartment air filter. If


you drive regularly under dusty conditions, the filter may require replacement more often. Inspect engine air cleaner filter. If necessary, replace the filter. If vehicle is driven in dusty/dirty conditions, inspect filter at every engine oil change. See Engine Air Cleaner/Filter on page 281 for more information. Inspect drive belt(s).


48,000 Miles (80 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


380


❑ ❑ 60,000 Miles (100 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Replace passenger compartment air filter. If


you drive regularly under dusty conditions, the filter may require replacement more often.


❑ Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 281 for more information.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


❑ Replace spark plugs. An Emission Control


Service.


❑ Replace spark plug wires. An Emission Control


Service. Inspect drive belt(s). ❑ Replace timing belt.


Inspect EVAP canister and vapor lines. Replace EVAP vent solenoid valve. An Emission Control Service. (See footnote †.) Inspect PCV system. An Emission Control Service. (See footnote †.)


❑ Change brake/clutch fluid (or every 24 months,


whichever occurs first).


63,000 Miles (105 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


66,000 Miles (110 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


69,000 Miles (115 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


72,000 Miles (120 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


381


❑ ❑ ❑ 75,000 Miles (125 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Replace passenger compartment air filter. If


you drive regularly under dusty conditions, the filter may require replacement more often. Inspect engine air cleaner filter. If necessary, replace the filter. If vehicle is driven in dusty/dirty conditions, inspect filter at every engine oil change. See Engine Air Cleaner/Filter on page 281 for more information. Inspect drive belt(s).


78,000 Miles (130 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


81,000 Miles (135 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


84,000 Miles (140 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Replace engine oil pan drain plug washer. ❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


87,000 Miles (145 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


382


❑ ❑ 90,000 Miles (150 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


❑ Replace passenger compartment air filter. If


you drive regularly under dusty conditions, the filter may require replacement more often.


❑ Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 281 for more information.


❑ Rotate tires. See Tire Inspection and Rotation


on page 327 for proper rotation pattern and additional information. (See footnote +.)


❑ Replace spark plugs. An Emission Control


Service.


❑ Replace fuel filter. An Emission Control


Service. (See footnote †.) Inspect drive belt(s). Inspect timing belt. Inspect EVAP canister, vapor lines, and EVAP vent solenoid valve. An Emission Control Service. (See footnote †.) Inspect PCV system. An Emission Control Service. (See footnote †.)


❑ Change brake/clutch fluid (or every 24 months,


whichever occurs first).


93,000 Miles (155 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service.


96,000 Miles (160 000 km)

Loading...
x