2012 Chevrolet Avalanche Owners Manual

If the vehicle has the remote start feature, the RKE transmitter functions will have an increased range of operation. However, the range may be less while the vehicle is running. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2‑2 for additional information. / (Remote Start): This button will be on the RKE transmitter if the vehicle has remote start. To start the vehicle using the remote start feature: 1. Aim the RKE transmitter at the

vehicle.

2. Press and release Q.

3.

Immediately press and hold / until the turn signal lamps flash. If you cannot see the vehicle's lamps, press and hold / for two to four seconds.

When the vehicle starts, the parking lamps will turn on and remain on while the vehicle is running. The doors will be locked and the climate control system may come on. The engine will continue to run for 10 minutes. Repeat the steps for a 10-minute time extension. Remote start can be extended only once.

After entering the vehicle during a remote start, insert and turn the key to ON/RUN to drive the vehicle. To cancel a remote start: . Aim the RKE transmitter at the vehicle and press and hold / until the parking lamps turn off. Turn on the hazard warning flashers. Turn the ignition on and then back off.

The vehicle can be remote started two separate times between driving sequences. The engine will run for 10 minutes after each remote start. Or, you can extend the engine run time by another 10 minutes within the first 10 minute remote start time frame, and before the engine stops. For example, if Q and then / are pressed again after the vehicle has been running for 5 minutes, 10 minutes are added, allowing the engine to run for 15 minutes. The additional 10 minutes are considered a second remote vehicle start. Once two remote starts, or a single remote start with one time extension has been done, the vehicle must be started with the key. After the key is removed from the ignition, the vehicle can be remote started again.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (7,1)

The vehicle cannot be remote started if the key is in the ignition, the hood is not closed, or if there is an emission control system malfunction and the check engine light is on. Also, the engine will turn off during a remote vehicle start if the coolant temperature gets too high or if the oil pressure gets low. Remote Start Ready If the vehicle does not have the remote vehicle start feature, it may have the remote start ready feature. This feature allows your dealer to add the manufacturer's remote vehicle start feature. See your dealer to add the manufacturer's remote vehicle start feature to the vehicle.

Keys, Doors, and Windows

2-7

Door Locks

{ WARNING Unlocked doors can be dangerous.

. Passengers, especially

children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked. So, all passengers should wear safety belts properly and the doors should be locked whenever the vehicle is driven.

. Young children who get into

unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent

(Continued)

WARNING (Continued)

injuries or even death from heat stroke. Always lock the vehicle whenever leaving it.

. Outsiders can easily enter through an unlocked door when you slow down or stop the vehicle. Locking the doors can help prevent this from happening.

There are several ways to lock and unlock the vehicle. From outside, use the Remote Keyless Entry (RKE) transmitter or the key in the driver door. From inside, use the power door locks or manual door locks. To lock or unlock the door with the manual locks, push down or pull up on the manual lock knob.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (8,1)

2-8

Keys, Doors, and Windows

Power Door Locks Press Q or K on the Remote Keyless Entry (RKE) transmitter. See Remote Keyless Entry (RKE) System Operation on page 2‑3.

Power Folding Mirrors Shown,

Other Models Similar

Q (Lock): Press to lock the doors. K (Unlock): Press to unlock the doors.

Delayed Locking When locking the doors with the power lock switch and a door is open, the doors will lock five seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. Pressing the power lock switch will override the delayed locking feature and immediately lock all the doors. This feature will not operate if the key is in the ignition. You can also program this feature using the Driver Information Center (DIC). See “Delay Door Lock” under Vehicle Personalization (With DIC Buttons) on page 5‑42.

Automatic Door Locks The vehicle may have an automatic lock/unlock feature. This feature can be programmed using the Driver Information Center (DIC).

See Vehicle Personalization (With DIC Buttons) on page 5‑42 for more information on DIC programming.

Lockout Protection If the driver side power door lock switch is pressed when the driver door is open and the key is in the ignition, all of the doors will lock and then the driver door will unlock. If the passenger side power door lock switch is pressed when the front passenger door is open and the key is in the ignition, all of the doors will lock and then the front passenger door will unlock.

Safety Locks The vehicle has rear door security locks to prevent passengers from opening the rear doors from the inside.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (9,1)

Keys, Doors, and Windows

2-9

Doors

Midgate®

{ WARNING

It can be dangerous to drive with the cargo area covered and the tailgate and the Midgate® open because carbon monoxide (CO) gas can come into your vehicle. You can not see or smell CO. It can cause unconsciousness and even death. If you must drive with the cargo covers on and the tailgate and Midgate open or if electrical wiring or other cable connections must pass through the seal between the body and the Midgate:

. Make sure all windows

are shut.

(Continued)

WARNING (Continued)

. Turn the fan on your heating

or cooling system to its highest speed on the setting that brings in outside air. This will force outside air into your vehicle. See Dual Automatic Climate Control System on page 8‑4.

. If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 9‑29.

Midgate Operation This vehicle is equipped with a Midgate and a removable rear glass panel. The Midgate allows you to extend the length of the vehicle's cargo area.

Open the rear doors to access the security locks on the inside edge of each door. To set the locks, insert a key into the slot and turn it to the horizontal position. The door can only be opened from the outside with the door unlocked. To return the door to normal operation, turn the slot to the vertical position.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (10,1)

2-10

Keys, Doors, and Windows

Rear Glass Removal and Storage

{ WARNING

If the removable rear glass is not stored properly, it could be thrown about the vehicle in a crash or sudden maneuver. People in the vehicle could be injured. Whenever you store the rear glass in the vehicle, always be sure that it is stored securely in the Midgate® storage pocket.

Do not remove the rear glass when the rear defroster is on. If you do, you may see a discharge spark coming from the latch area. To remove the rear glass do the following: 1. Fold the rear seats. See Rear Seats on page 3‑10. The front seats may have to be moved forward slightly to allow the rear seats to fold completely.

Although the rear glass can be removed without folding the rear seats, you will not be able to access the rear glass storage pocket. Be sure to fold the seats before removing the rear glass.

2. Squeeze and pull down the latch

levers (A), located near the upper corners of the rear glass, to unlatch. Once unlatched, the glass-catch release button (C) will catch the rear glass and prevent it from falling forward.

The following are the main components of the Midgate system: A. Latch Levers B. Grab Handles C. Glass-Catch Release Button D. Glass Lock Knobs E. Glass Retaining Tabs F. Midgate Release Handle G. Glass Alignment Arrows

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (11,1)

Keys, Doors, and Windows

2-11

3. While holding the rear glass in

4. With the rear glass tilted toward

5. Load the rear glass into the

place, press the glass-catch release button (C) and pull the top of the rear glass toward you using the grab handles (B) located at the top of the rear glass.

you, lift it out from the lower window frame channel. Use the grab handles (B) to assist you in removing the rear glass.

storage pocket in the Midgate, guiding the lower edge of the rear glass behind the three rear glass retaining tabs (E). Hold the rear glass flat against the storage pocket, with grab handles facing you, until the next step.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (12,1)

2-12

Keys, Doors, and Windows

6. Turn both glass lock knobs (D),

located at both top corners of the storage pocket, to the locked position. Push in on the corner of the rear glass to allow the lock knob to engage more easily.

Once both glass lock knobs are in the locked position, the rear glass is securely stored.

7. Push both latch levers up to the locked position. You should hear a click when each latch lever locks correctly. The rear seats can be returned to the normal position when the rear glass is out and stored properly in the storage pocket.

Reinstalling the Rear Glass To reinstall the rear glass, do the following: 1. Squeeze and pull down the latch

levers (A), located near the upper corners of the rear glass, to unlatch.

2. Hold the rear glass in place with one hand and turn the glass lock knobs, located at both top corners of the glass storage pocket, to the unlocked position.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (13,1)

Keys, Doors, and Windows

2-13

3. Pull the rear glass out from the storage pocket using the grab handles (B).

4. With the rear glass tilted at an

angle, place the bottom edge in the lower channel of the window frame.

Be sure to align the rear glass side-to-side using the glass alignment arrows (G).

5. Apply a firm downward pressure and then push the rear glass flat against the window frame. Use the grab handles (B) at the top of the rear glass to assist you.

6. Push the rear glass flat against

the window frame and push each latch lever (A) up until it locks. You should hear a click when each latch lever locks correctly.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (14,1)

2-14

Keys, Doors, and Windows

Lowering the Midgate with the Rear Glass in Place The Midgate can be lowered to allow the cargo area of your vehicle to extend into the cab. The rear glass can be either installed in its normal position, or it can be removed and stored in the rear glass storage pocket. To lower the Midgate: 1. Fold the rear seats. The front seats might have to be moved forward slightly to allow the rear seats to fold. See Rear Seats on page 3‑10.

Rear Glass in Normal Position 2. Standing outside of the vehicle, hold the Midgate securely so it does not fall forward. Turn the Midgate handle clockwise and pull the Midgate toward you.

Lowering the Midgate with the Rear Glass in the Storage Pocket

Rear Glass Stored in Glass

Storage Pocket

3. Lower the Midgate until it is flat.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (15,1)

Keys, Doors, and Windows

2-15

Raising the Midgate To return the Midgate to its normal position, raise the Midgate up with a firm swinging motion until it latches into place securely. This will help to ensure that the Midgate closes with enough force to engage the latches. If the rear glass is removed and you would like to put it back, do so using the instructions given previously.

Tailgate

{ WARNING

It is extremely dangerous to ride on the tailgate, even when the vehicle is operated at low speeds. People riding on the tailgate can easily lose their balance and fall in response to vehicle maneuvers. Falling from a moving vehicle may result in serious injuries or death. Do not allow people to ride on the tailgate.

(Continued)

WARNING (Continued)

Be sure everyone in your vehicle is in a seat and using a safety belt properly.

Use the Remote Keyless Entry (RKE) transmitter or power door lock switch to lock and unlock the tailgate. Open the tailgate by lifting up on its handle while pulling the tailgate toward you. To close the tailgate, push it firmly upward until it latches. Push and pull on the tailgate to be sure it is latched securely. Tailgate Removal The tailgate is not to be removed. Removing the tailgate may cause damage to electrical connector resulting in loss of lock/unlock and rear vision camera function.

Midgate Lowered with Crossbar

Attached

This procedure works the same as the procedure described previously, but when you lower the Midgate with the rear glass in the stored position, you will notice that the entire crossbar will lower with the Midgate. This is completely normal; however, since the crossbar lowers with the Midgate, it will be heavier. As you lower the Midgate be ready for the extra weight and do not let the Midgate fall as you lower it.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (16,1)

2-16

Keys, Doors, and Windows

Power Assist Steps

The power assist steps automatically extend from beneath the vehicle on the side in which the door has been opened. Once the door is closed, the assist steps automatically move back under the vehicle after a brief delay. The vehicle must not be moving for the assist steps to extend or retract. The assist steps cannot be disabled in the extended position.

Vehicle Security This vehicle has theft-deterrent features; however, they do not make it impossible to steal.

Anti-theft Alarm System Your vehicle has a content theft-deterrent alarm system.

The vehicle may have power assist steps. To enable or disable the power assist steps push j.

This is the security light. To arm the theft-deterrent system: 1. Open the door. 2. Lock the door with the Remote Keyless Entry (RKE) transmitter or the power door lock switch. The security light will come on to inform the driver the system is arming. If a door is open when the doors are locked, the security light will flash.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (17,1)

If the delayed locking feature is turned on, the theft‐deterrent system will not start the arming process until the last door is closed and the delay timer has expired. See Delayed Locking on page 2‑8.

3. Close all doors. The security light should go off after about 30 seconds. The alarm is not armed until the security light goes off. The content theft deterrent system does not sense if the midgate or tailgate are open or ajar, therefore, vehicle contents may not be protected if the midgate is left open or ajar.

If a locked driver door is opened without using the RKE transmitter, a ten second pre-alarm will occur. The horn will chirp and the lights will flash. If the key is not placed in the ignition and turned to START or the door is not unlocked by pressing the

Keys, Doors, and Windows

2-17

unlock button on the RKE transmitter during the ten second pre-alarm, the alarm will go off. Your vehicle's headlamps will flash and the horn will sound for about 30 seconds, then will turn off to save the battery power. The theft-deterrent system will not activate if the doors are locked with the vehicle's key or the manual door lock. It activates only if you use the power door lock switch with the door open or the RKE transmitter. You should also remember that you can start your vehicle with the correct ignition key if the alarm has been set off. To avoid setting off the alarm by accident:

If you do not want to activate the theft-deterrent system, the vehicle should be locked with the door key after the doors are closed.

. Always unlock the doors with the

RKE transmitter. Unlocking a door any other way will set off the alarm if it is armed.

If you set off the alarm by accident, press unlock on the RKE transmitter or place the key in the ignition and turn it to START to turn off the alarm. The alarm will not stop if you try to unlock a door any other way. Testing the Alarm To test the alarm: 1. From inside the vehicle, lower

the driver window and open the driver door.

2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the RKE transmitter.

3. Get out of the vehicle, close the

door and wait for the security light to go out.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (18,1)

2-18

Keys, Doors, and Windows

4. Then reach in through the

window, unlock the door with the manual door lock and open the door. This should set off the alarm.

While the alarm is set, the power door unlock switch will not work. If the alarm does not sound when it should but the headlamps flash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Instrument Panel Fuse Block on page 10‑42 and Engine Compartment Fuse Block on page 10‑38. If the alarm does not sound or the headlamps do not flash, the vehicle should be serviced by your dealer.

Immobilizer See Radio Frequency Statement on page 13‑20 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-GEN/210/220/310.

Immobilizer Operation This vehicle has PASS-Key® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. The system is automatically disarmed when the key is turned to ON/RUN, ACC/ACCESSORY, or START from the LOCK/OFF position. You do not have to manually arm or disarm the system. The security light will come on if there is a problem with arming or disarming the theft-deterrent system. When the PASS-Key III+ system senses that someone is using the wrong key, it prevents the vehicle from starting. Anyone using a

trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. If the engine does not start and the security light on the instrument panel cluster comes on when trying to start the vehicle, there may be a problem with the theft-deterrent system. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse. See Fuses and Circuit Breakers on page 10‑38. If the engine still does not start with the other key, the vehicle needs service. If the vehicle does start, the first key may be faulty. See your dealer who can service the PASS-Key III+ to have a new key made. It is possible for the PASS-Key III+ decoder to learn the transponder value of a new or replacement key.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (19,1)

Keys, Doors, and Windows

2-19

Up to 10 keys may be programmed for the vehicle. The following procedure is for programming additional keys only. If all the currently programmed keys are lost or do not operate, you must see your dealer or a locksmith who can service PASS-Key III+ to have keys made and programmed to the system. See your dealer or a locksmith who can service PASS-Key III+ to get a new key blank cut exactly as the ignition key that operates the system. To program the new additional key: 1. Verify that the new key has

a 1 stamped on it.

2.

Insert the original, already programmed key in the ignition and start the engine. If the engine will not start, see your dealer for service.

3. After the engine has started,

4.

turn the key to LOCK/OFF, and remove the key. Insert the new key to be programmed and turn it to the ON/RUN position within five seconds of turning the ignition to the LOCK/OFF position in Step 3. The security light will turn off once the key has been programmed.

5. Repeat Steps 1 through 4 if

additional keys are to be programmed.

If you lose or damage your PASS-Key III+ key, see your dealer or a locksmith who can service PASS-Key III+ to have a new key made. Do not leave the key or device that disarms or deactivates the theft-deterrent system in the vehicle.

Exterior Mirrors

Convex Mirrors

{ WARNING

A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.

The passenger side mirror is convex shaped. A convex mirror's surface is curved so more can be seen from the driver seat.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (20,1)

2-20

Keys, Doors, and Windows

Power Mirrors

With Power Folding Mirrors

To adjust the mirrors: 1. Press (A) or (B) to select the

driver or passenger side mirror. 2. Press the arrows on the control

pad to move the mirror up, down, right, or left.

3. Adjust the outside mirror so that

the side of the vehicle and the area behind are seen.

4. Press either (A) or (B) again to

deselect the mirror.

With Manual Folding Mirrors

To adjust the mirrors: 1. Move the selector switch located

above the four-way control pad to the left or right to choose either the driver side or passenger side mirror.

2. Press one of the four arrows located on the control pad to move the mirror in the desired direction.

3. Adjust the outside mirror so that

the side of the vehicle and the area behind are seen.

Keep the selector switch in the center position when not adjusting either outside mirror. Exterior Automatic Dimming Mirror If the vehicle has the exterior automatic dimming mirror, the driver outside mirror automatically adjusts for the glare of headlamps behind. This feature is controlled by the on and off setting on the inside automatic dimming rearview mirror. See Automatic Dimming Rearview Mirror on page 2‑22 for more information. Turn Signal Indicator The vehicle may also have a turn signal indicator on the mirror. An arrow on the mirror flashes in the direction of the turn or lane change.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (21,1)

Folding Mirrors

Power Folding

1. Press (A) to fold the mirrors out

to the driving position.

2. Press (B) to fold the mirrors in to

the folded position.

Keys, Doors, and Windows

2-21

Heated Mirrors 1 (Rear Window Defogger): Press to heat the mirrors. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 8‑4 or Climate Control Systems on page 8‑1 for more information.

Automatic Dimming Mirror If the vehicle has the automatic dimming mirror, the driver outside mirror automatically adjusts for the glare of the headlamps from behind. This feature is controlled by the on and off setting on the inside rearview mirror. See Automatic Dimming Rearview Mirror on page 2‑22 for more information.

Resetting the Power Folding Mirrors Reset the power folding mirrors if:

The mirrors are accidentally obstructed while folding. They are accidentally manually folded/unfolded. The mirrors will not stay in the unfolded position. The mirrors vibrate at normal driving speeds.

Fold and unfold the mirrors one time using the mirror controls to reset them to their normal position. A popping noise may be heard during the resetting of the power folding mirrors. This sound is normal after a manual folding operation. Manual Folding Fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, pull the mirror toward the vehicle. Push the mirror outward, to return to its original position.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (22,1)

2-22

Keys, Doors, and Windows

Park Tilt Mirrors If the vehicle has the memory package, the exterior mirrors tilt to a preselected position when the vehicle is in R (Reverse). This feature lets the driver view the curb when parallel parking. The mirrors return to the original position when the vehicle is shifted out of R (Reverse), or the ignition is turned off or to OFF/LOCK. This feature can be programed through the Driver Information Center (DIC). See Vehicle Personalization (With DIC Buttons) on page 5‑42 for more information.

Interior Mirrors

Manual Rearview Mirror To adjust the inside rearview mirror, hold the rearview mirror in the center and move it to view the area behind the vehicle. For vehicles with a manual rearview mirror, push the tab forward for daytime use and pull it for nighttime use to avoid glare from the headlamps from behind. Vehicles with OnStar® have three control buttons at the bottom of the mirror. See a dealer for more information about OnStar and how to subscribe to it. See OnStar Overview on page 14‑1.

Automatic Dimming Rearview Mirror To adjust the inside rearview mirror, hold the rearview mirror in the center and move it to view the area behind the vehicle. For vehicles with an automatic dimming rearview mirror. The mirror will automatically reduce the glare from the headlamps from behind. The dimming feature comes on and the indicator light illuminates when the vehicle is started. O (On/Off): Press to turn the dimming feature on or off. The vehicle may also have a Rear Vision Camera (RVC). See Rear Vision Camera (RVC) on page 9‑52
for more information.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (23,1)

Keys, Doors, and Windows

2-23

If the vehicle has a RVC, the O button for turning the automatic dimming rearview mirror feature on or off will not be available. Vehicles with OnStar have three additional control buttons located at the bottom of the mirror. See a dealer for more information about OnStar and how to subscribe to it. See OnStar Overview on page 14‑1. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water.

Windows

{ WARNING

Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.

The vehicle aerodynamics are designed to improve fuel economy performance. This may result in a pulsing sound when a window is partially open. To reduce the sound, open another window or the sunroof (if equipped).

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (24,1)

2-24

Keys, Doors, and Windows

Express Down Windows Windows that have the express‐ down feature allow the windows to be lowered without holding the switch. Press the window switch fully and release it to activate the express‐down feature. The express mode can be canceled at any time by briefly pressing, or pulling the switch.

Power Windows

{ WARNING

Leaving children in a vehicle with the keys is dangerous for many reasons. Children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window. Do not leave keys in a vehicle with children. When there are children in the rear seat use the window lockout button to prevent unintentional operation of the windows.

Power Folding Mirrors Shown,

Other Models Similar

The driver door has switches that control all windows, the passengers door switch only control that window. The power windows work when the ignition is in ON/RUN or ACC/ACCESSORY, or in Retained Accessory Power (RAP). See Retained Accessory Power (RAP) on page 9‑26 for more information. Press the switch to lower the window. Pull the switch up to raise it.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/8/11

Black plate (25,1)

Window Lockout

Sun Visors

Keys, Doors, and Windows

2-25

Roof

Sunroof

Pull the sun visor down to block glare. Detach the sun visor from the center mount to pivot to the side window, or to extend along the rod, if available.

Power Folding Mirrors Shown,

Other Models Similar This feature prevents the rear passenger windows from operating, except from the driver position. . Press o to activate the rear

window locks. An indicator light will illuminate when the feature is on.

. Press o again to deactivate the

rear window locks.

A. Open or Close B. Vent On vehicles with a sunroof, the sunroof only operates when the ignition is in the ACC/ACCESSORY or ON/RUN, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 9‑26.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (26,1)

2-26

Keys, Doors, and Windows

Vent: From the closed position, press the rear of switch (B) to vent the sunroof. Open/Close: To open the sunroof, press and hold switch (A) until the sunroof reaches the desired position. Press and hold the front of switch (A) to close it. Express-Open/Express-Close: To express-open the sunroof, fully press and release the rear of switch (A) until the sunroof reaches the desired position. To express-close the sunroof, fully press and release the front of switch (A). Press the switch again to stop it.

When the sunroof is opened, an air deflector will automatically raise. The air deflector will retract when the sunroof is closed. The sunroof also has a sunshade which can be pulled forward to block sun rays. The sunshade must be opened and closed manually. If an object is in the path of the sunroof while it is closing, the anti-pinch feature will detect the object and stop the sunroof.

Dirt and debris may collect on the sunroof seal or in the track. This could cause an issue with sunroof operation or noise. It could also plug the water drainage system. Periodically open the sunroof and remove any obstacles or loose debris. Wipe the sunroof seal and roof sealing area using a clean cloth, mild soap, and water. Do not remove grease from the sunroof.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (1,1)

Seats and Restraints

3-1

Child Restraints

Older Children . . . . . . . . . . . . . . . 3-34
Infants and Young

Children . . . . . . . . . . . . . . . . . . . . 3-37
Child Restraint Systems . . . . . 3-39
Where to Put the Restraint . . . 3-41
Lower Anchors and Tethers

for Children (LATCH System) . . . . . . . . . . . . . . . . . . . . 3-43

Replacing LATCH System

Parts After a Crash . . . . . . . . . 3-49

Securing Child Restraints

(Rear Seat Position) . . . . . . . . 3-49

Securing Child Restraints

(Center Front Seat Position) . . . . . . . . . . . . . . . . . . . 3-51

Securing Child Restraints

(Right Front Seat Position) . . . . . . . . . . . . . . . . . . . 3-52

Seats and Restraints

Head Restraints

Head Restraints . . . . . . . . . . . . . . . 3-2

Front Seats

Seat Adjustment . . . . . . . . . . . . . . 3-3
Center Seat . . . . . . . . . . . . . . . . . . . 3-4
Power Seat Adjustment . . . . . . . 3-4
Lumbar Adjustment . . . . . . . . . . . 3-4
Reclining Seatbacks . . . . . . . . . . 3-5
Memory Seats . . . . . . . . . . . . . . . . 3-7
Heated and Ventilated Front

Seats . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Rear Seats

Rear Seats . . . . . . . . . . . . . . . . . . 3-10

Safety Belts

Safety Belts . . . . . . . . . . . . . . . . . . 3-11
How to Wear Safety Belts

Properly . . . . . . . . . . . . . . . . . . . . 3-12
Lap-Shoulder Belt . . . . . . . . . . . 3-13
Safety Belt Use During

Pregnancy . . . . . . . . . . . . . . . . . . 3-18
Lap Belt . . . . . . . . . . . . . . . . . . . . . 3-18

Safety Belt Extender . . . . . . . . . 3-19
Safety System Check . . . . . . . . 3-19
Safety Belt Care . . . . . . . . . . . . . 3-19
Replacing Safety Belt System

Parts after a Crash . . . . . . . . . 3-20

Airbag System

Airbag System . . . . . . . . . . . . . . . 3-20
Where Are the Airbags? . . . . . 3-22
When Should an Airbag

Inflate? . . . . . . . . . . . . . . . . . . . . . 3-24

What Makes an Airbag

Inflate? . . . . . . . . . . . . . . . . . . . . . 3-25

How Does an Airbag

Restrain? . . . . . . . . . . . . . . . . . . . 3-26

What Will You See after an

Airbag Inflates? . . . . . . . . . . . . 3-26

Passenger Sensing

System . . . . . . . . . . . . . . . . . . . . . 3-28

Servicing the Airbag-Equipped

Vehicle . . . . . . . . . . . . . . . . . . . . . 3-32

Adding Equipment to the

Airbag-Equipped Vehicle . . . 3-32
Airbag System Check . . . . . . . . 3-33
Replacing Airbag System

Parts after a Crash . . . . . . . . . 3-34

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (2,1)

3-2

Seats and Restraints

Head Restraints

Front Seats The front seats have adjustable head restraints in the outboard seating positions.

{ WARNING

With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.

Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head. This position reduces the chance of a neck injury in a crash.

The height of the head restraint can be adjusted. Pull the head restraint up to raise it. Try to move the head restraint to make sure that it is locked in place. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Try to move the head restraint after the button is released to make sure that it is locked in place. The front seat outboard head restraints are not designed to be removed.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (3,1)

Seats and Restraints

3-3

Rear Seats The rear seat has adjustable headrests in the outboard seating positions. The height of the headrest can be adjusted. Pull the headrest up to raise it. To lower the headrest, push down on the headrest. Rear outboard headrests are not designed to be removed.

Front Seats

Seat Adjustment

{ WARNING You can lose control of the vehicle if you try to adjust a driver seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver seat only when the vehicle is not moving.

To adjust the seat: 1. Lift the bar under the front edge

of the seat cushion to unlock the seat.

2. Slide the seat to the desired position and release the bar.

3. Try to move the seat back and

forth to be sure the seat is locked in place.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (4,1)

3-4

Seats and Restraints

Center Seat If equipped, the center front seatback doubles as an armrest and cupholder/storage area for the driver and passenger when the center front seat is not used. Do not use it as a seating position when the seatback is folded down.

Power Seat Adjustment

If available, raise or lower the front or rear part of the seat cushion by moving the front or rear of the control up or down. If available, raise or lower the entire seat by moving the entire control up or down.

To adjust the seatback, see “Power Reclining Seatbacks” under Reclining Seatbacks on page 3‑5.

Lumbar Adjustment

Manual Lumbar

To adjust a power seat, if equipped: . Move the seat forward or

rearward by sliding the control forward or rearward.

If equipped, increase or decrease manual lumbar support by turning the knob forward or rearward. Power Lumbar

To adjust the power lumbar support, if equipped: . On vehicles with two-way

lumbar, press and hold the top or bottom of the control to increase or decrease lumbar support.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (5,1)

Seats and Restraints

3-5

WARNING (Continued)

The lap belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear the safety belt properly.

Do not have a seatback reclined if the vehicle is moving.

. On vehicles with four-way

lumbar, press and hold the front or rear of the control to increase or decrease lumbar support. To raise or lower the height of the support, press and hold the top or bottom of the control.

Reclining Seatbacks { WARNING

Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job. The shoulder belt will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries.

(Continued)

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (6,1)

3-6

Seats and Restraints

Manual Reclining Seatbacks

{ WARNING

If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.

The seatback will automatically fold forward.

2. To recline, move the seatback

rearward to the desired position, then release the lever to lock the seatback in place.

3. Push and pull on the seatback to

make sure it is locked.

To return the seatback to the upright position: 1. Lift the lever fully without applying pressure to the seatback, and the seatback will return to the upright position.

2. Push and pull on the seatback to

make sure it is locked.

Power Reclining Seatbacks

To recline a power seatback, if equipped:

Tilt the top of the control rearward to recline. Tilt the top of the control forward to raise.

To adjust a manual seatback: 1. Lift the lever.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (7,1)

Memory Seats

On vehicles with the memory feature, the controls on the driver door are used to program and recall memory settings for the driver seat, outside mirrors, and the adjustable throttle and brake pedals, if equipped.

Storing Memory Positions To save into memory: 1. Adjust the driver seat, seatback

recliner, both outside mirrors, and the throttle and brake pedals, if equipped. See Power Mirrors on page 2‑20
and Adjustable Throttle and Brake Pedal on page 9‑21. Not all mirrors and adjustable throttle and brake pedals will have the ability to save and recall their positions.

2. Press and hold “1” until

two beeps sound.

3. Repeat for a second driver

position using “2.”

Seats and Restraints

3-7

To recall, press and release “1” or “2.” The vehicle must be in P (Park). A single beep will sound. The seat, outside mirrors, and adjustable throttle and brake pedals will move to the position previously stored for the identified driver.

Memory Remote Recall The memory feature can recall the driver seat, outside mirrors, and pedals, if equipped, to stored positions when entering the vehicle. To activate, unlock the driver door with the Remote Keyless Entry (RKE) transmitter. The driver seat, outside mirrors, and adjustable pedals, if equipped, will move to the memory position associated with the transmitter used to unlock the vehicle.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (8,1)

3-8

Seats and Restraints

This feature can be turned on or off using the vehicle personalization menu. See Vehicle Personalization (With DIC Buttons) on page 5‑42. To stop recall movement, press one of the power seat controls, memory buttons, or power mirror buttons, or the adjustable pedal switch. If something has blocked the driver seat and/or the adjustable pedals while recalling a memory position, the recall may stop. Remove the obstruction; then press and hold the appropriate manual control for the memory item that is not recalling for two seconds. Try recalling the memory position again by pressing the appropriate memory button. If the memory position is still not recalling, see your dealer for service.

Easy Exit Driver Seat This feature can move the seat rearward to allow extra room to exit the vehicle.

B (Easy Exit Driver Seat): Press to recall the easy exit seat position. The vehicle must be in P (Park). If the easy exit seat feature is programmed on in the vehicle personalization menu, automatic seat movement occurs when the ignition key is removed. A single beep sounds. The driver seat moves back approximately 8 cm (3 in). To move the seat back farther, press B again until the seat is all the way back. If something has blocked the driver seat while recalling the exit position, the recall may stop. Remove the obstruction; then press and hold the power seat control rearward for two seconds. Try recalling the exit position again. If the exit position is still not recalling, see your dealer for service. See Vehicle Personalization (With DIC Buttons) on page 5‑42.

Heated and Ventilated Front Seats

{ WARNING

If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures. To reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover, or similar item. This may cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (9,1)

Seats and Restraints

3-9

Remote Start Heated Seats When it is cold outside, the heated seats may turn on automatically during a remote vehicle start. The heated seats will be canceled when the ignition is turned on. Press the desired button to use the heated seats after the vehicle is started. The lights on the heated seat buttons do not turn on during a remote start. The temperature performance of an unoccupied seat may be reduced. This is normal. See Remote Vehicle Start on page 2‑5.

J (Heated Seat and Seatback): Press to heat the seat and seatback. Press the button once for the highest setting. With each press of the button, the seat will change to the next lower setting, and then to the off setting. The lights indicate three for the highest setting and one for the lowest. The passenger seat may take longer to heat up. On vehicles with heated seats, the heated seats are canceled 10 seconds after the ignition is turned off. On vehicles with heated and cooled seats, the heated and cooled seats are canceled when the ignition is turned off. To use this feature after restarting the vehicle, press the desired button again.

Heated and Cooled Seat Buttons

Shown, Heated Seat Buttons

Similar

If available, the buttons are on the front doors. To operate, the ignition must be in ON/RUN. H (Cooled Seat): press to cool the seat. I (Heated Seatback): Press to heat the seatback only.

If available,

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (10,1)

3-10

Seats and Restraints

Rear Seats The rear seatbacks can be folded to provide more cargo space and access to the midgate. See Midgate® on page 2‑9. To fold the seatback: 1. Push the rear seat headrests all

the way down.

Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.

4. Repeat the procedure for the

other seatback, if desired.

To return the seats to the normal position, lift the seatback up and fold the seat cushion down. { WARNING

A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.

3. Fold the seatback forward until it

is flat. If necessary, move the front seats forward slightly to allow the seatback to fold completely.

2. Pull the loop in the crease where

the seatback and seat cushion meet to release the seat cushion. Tilt the seat cushion forward toward the front of the vehicle.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (11,1)

{ WARNING

If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always be sure to press the rear of the seat cushion down. This action locks the seatback in place.

Push and pull on the seatback to make sure it is locked. Raise the headrest.

Safety Belts This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts.

{ WARNING

Do not let anyone ride where a safety belt cannot be worn properly. In a crash, if you or your passenger(s) are not wearing safety belts, injuries can be much worse than if you are wearing safety belts. You can be seriously injured or killed by hitting things inside the vehicle harder or by being ejected from the vehicle. In addition, anyone who is not buckled up can strike other passengers in the vehicle.

(Continued)

Seats and Restraints

3-11

WARNING (Continued)

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, passengers riding in these areas are more likely to be seriously injured or killed. Do not allow passengers to ride in any area of the vehicle that is not equipped with seats and safety belts. Always wear a safety belt, and check that all passenger(s) are restrained properly too.

This vehicle has indicators as a reminder to buckle the safety belts. See Safety Belt Reminders on page 5‑14.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (12,1)

3-12

Seats and Restraints

Why Safety Belts Work

When riding in a vehicle, you travel as fast as the vehicle does. If the vehicle stops suddenly, you keep going until something stops you. It could be the windshield, the instrument panel, or the safety belts! When you wear a safety belt, you and the vehicle slow down together. There is more time to stop because you stop over a longer distance and, when worn properly, your strongest bones take the forces from the

safety belts. That is why wearing safety belts makes such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt?

A: You could be — whether you are

wearing a safety belt or not. Your chance of being conscious during and after a crash, so you can unbuckle and get out, is much greater if you are belted.

Q: If my vehicle has airbags, why

should I have to wear safety belts?

A: Airbags are supplemental

systems only; so they work with safety belts — not instead of them. Whether or not an airbag is provided, all occupants still have to buckle up to get the most protection.

Also, in nearly all states and in all Canadian provinces, the law requires wearing safety belts.

How to Wear Safety Belts Properly This section is only for people of adult size. There are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 3‑34 or Infants and Young Children on page 3‑37. Follow those rules for everyone's protection. It is very important for all occupants to buckle up. Statistics show that unbelted people are hurt more often in crashes than those who are wearing safety belts. There are important things to know about wearing a safety belt properly.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (13,1)

. Wear the shoulder belt over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt locks if there is a sudden stop or crash.

{ WARNING

You can be seriously injured, or even killed, by not wearing your safety belt properly. . Never allow the lap or

shoulder belt to become loose or twisted.

. Never wear the shoulder belt

under both arms or behind your back.

. Never route the lap or shoulder belt over an armrest.

Seats and Restraints

3-13

Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt except for the center front passenger position (if equipped), which has a lap belt. See Lap Belt on page 3‑18 for more information. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index.

2. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.

. Sit up straight and always keep

your feet on the floor in front of you.

. Always use the correct buckle

for your seating position.

. Wear the lap part of the belt low

and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (14,1)

3-14

Seats and Restraints

If the shoulder portion of a passenger belt is pulled out all the way, the child restraint locking feature may be engaged. If this happens, let the belt go back all the way and start again. Engaging the child restraint locking feature may affect the passenger sensing system, if equipped. See Passenger Sensing System on page 3‑28
for more information. If the belt stops before it reaches the buckle, tilt the latch plate and keep pulling the safety belt until it can be buckled.

4.

If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See “Shoulder Belt Height Adjuster” in this section for instructions on use and important safety information.

3. Push the latch plate into the

buckle until it clicks. If you find that the latch plate will not go fully into the buckle, see if you are using the correct buckle. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 3‑19. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.

5. To make the lap part tight, pull

up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (15,1)

Adjust the height so the shoulder portion of the belt is on the shoulder and not falling off of it. The belt should be close to, but not contacting, the neck. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. See How to Wear Safety Belts Properly on page 3‑12.

To unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Before a door is closed, be sure the safety belt is out of the way. If a door is slammed against a safety belt, damage can occur to both the belt and the vehicle. Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger positions.

Squeeze the buttons (A) on the sides of the height adjuster and move the height adjuster to the desired position.

Seats and Restraints

3-15

The adjuster can be moved up just by pushing up on the shoulder belt guide. After the adjuster is set to the desired position, try to move it down without squeezing the buttons to make sure it has locked into position. Safety Belt Pretensioners This vehicle has safety belt pretensioners for front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly. They can help tighten the safety belts during the early stages of a moderate to severe frontal, near frontal, or rear crash if the threshold conditions for pretensioner activation are met. And, if the vehicle has side impact airbags, safety belt pretensioners can help tighten the safety belts in a side crash or a rollover event.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (16,1)

3-16

Seats and Restraints

Pretensioners work only once. If the pretensioners activate in a crash, they will need to be replaced, and probably other new parts for the vehicle's safety belt system. See Replacing Safety Belt System Parts after a Crash on page 3‑20. Rear Safety Belt Comfort Guides This vehicle may have rear shoulder belt comfort guides. If not, they are available through your dealer. The guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed and properly adjusted, the comfort guide positions the belt away from the neck and head.

There is one guide, if equipped, for each outside passenger position in the rear seat. Here is how to install a comfort guide to the safety belt: 1. Remove the guide from its

storage pocket on the side of the seat.

2. Place the guide over the belt,

and insert the two edges of the belt into the slots of the guide.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (17,1)

Seats and Restraints

3-17

{ WARNING

A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.

3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.

4. Buckle, position, and release

the safety belt as described previously in this section. Make sure the shoulder portion of the belt is on the shoulder and not falling off of it. The belt should be close to, but not contacting, the neck.

To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide. Slide the guide into its storage clip on the interior body or storage pocket on the side of the seat.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (18,1)

3-18

Seats and Restraints

Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts.

A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.

The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.

Lap Belt This part is only for the lap belt. To learn how to wear a lap-shoulder belt, see Lap-Shoulder Belt on page 3‑13. The vehicle may have a center seating position. When you sit in the center front seating position, you have a lap safety belt, which has no retractor.

To make the belt longer, tilt the latch plate and pull it along the belt. Buckle, position and release it the same way as the lap part of a lap-shoulder belt.

Chevrolet Avalanche Owner Manual - 2012 - crc 2nd edition - 11/7/11

Black plate (19,1)

Seats and Restraints

3-19

from doing its job. See your dealer to have it repaired. Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away. Make sure the safety belt reminder light is working. See Safety Belt Reminders on page 5‑14. Keep safety belts clean and dry. See Safety Belt Care on page 3‑19.

Safety Belt Care Keep belts clean and dry. { WARNING

Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.

Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer will order you