2011 Cadillac SRX Owners Manual

10-90

Vehicle Care

3. Remove the spare tire cover.

4. Remove the nut retaining the

spare tire.

5. Remove the spare tire and place it next to the tire being changed.

6. Remove the wing nut (D). 7. Remove the extension (A),

jack (B) and wheel wrench (C) and place them near the tire being changed.

Cadillac SRX Owner Manual - 2011

Black plate (91,1)

Vehicle Care

10-91

Removing the Flat Tire and Installing the Spare Tire Take off the wheel cover or center cap, if the vehicle has one, to reach the wheel bolts. 1. Do a safety check before

proceeding. See If a Tire Goes Flat on page 10‑79 for more information.

2. Turn the wheel wrench

counterclockwise to loosen and remove the wheel nut caps. Do not try to remove plastic caps from the cover or center cap.

3. Pull the cover or center cap away from the wheel. Store the wheel cover in the cargo area until you have the flat tire repaired or replaced.

4. Turn the wheel wrench

counterclockwise to loosen all the wheel nuts, but do not remove them yet.

5. Place the jack near the flat tire. Notice: Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty.

6. Position the jack lift head at the jack location nearest the flat tire. The jacking location is indicated by a V-shaped notch in the plastic molding. The jack must not be used in any other position.

Cadillac SRX Owner Manual - 2011

Black plate (92,1)

10-92

Vehicle Care

8. Turn the extension with the

wheel wrench clockwise to raise the jack lift head until the jack just fits under the vehicle.

9. Raise the vehicle by turning the wheel wrench clockwise until the slots in the jack head fit into the metal flange located behind the triangle on the plastic moulding.

{ WARNING Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

{ WARNING Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

7.

Insert the hooked end of the extension handle through the jack and the flat end through the wheel wrench.

{ WARNING

Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

Cadillac SRX Owner Manual - 2011

Black plate (93,1)

Vehicle Care

10-93

Notice: Using a jack to raise the vehicle without positioning it correctly could damage your vehicle. When raising your vehicle on a jack, be sure to position it correctly under the frame and avoid contact with the plastic molding. 10. Put the compact spare tire

near you.

{ WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See If a Tire Goes Flat on page 10‑79.

Remove all of the wheel nuts.

11. Remove the flat tire.

12. Remove any rust or dirt from

the wheel bolts, mounting surfaces, and spare wheel.

13. Place the compact spare tire

on the wheel-mounting surface.

{ WARNING

Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.

Cadillac SRX Owner Manual - 2011

Black plate (94,1)

10-94

Vehicle Care

14. Reinstall the wheel nuts. Tighten each nut by hand until the wheel is held against the hub.

15. Lower the vehicle by

turning the jack handle counterclockwise.

{ WARNING

Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 12‑2 for the wheel nut torque specification.

Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12‑2 for original equipment wheel nut torque specifications.

16. Tighten the wheel nuts firmly

in a crisscross sequence, as shown.

17. Lower the jack all the way and remove the jack from under the vehicle.

18. Tighten the wheel nuts firmly

with the wheel wrench.

When reinstalling the wheel cover or center cap on the full-size tire, tighten all five plastic caps hand snug with the aid of the wheel wrench and tighten them with the wheel wrench an additional one‐quarter of a turn. Notice: Wheel covers will not fit on the vehicle's compact spare. If you try to put a wheel cover on the compact spare, the cover or the spare could be damaged.

Cadillac SRX Owner Manual - 2011

Black plate (95,1)

Vehicle Care

10-95

3.

Install the cargo cover. For more information, see Cargo Management System on page 4‑4.

4. Place the tire, lying flat, in the

rear storage compartment.

6. Route the strap through the

wheel, as shown.

7. Attach the strap to the other cargo tie-down in the rear of the vehicle.

8. Tighten the strap. The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can.

5. Attach the strap to the cargo

tie-down in the rear of the vehicle.

Storing a Flat or Spare Tire and Tools

{ WARNING

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

To store the flat or spare tire and tools: 1. Open the liftgate. See Liftgate

on page 2‑14 for more information.

2. Put back all tools as they

were stored in the rear storage compartment and put the compartment cover back on. For more information, see “Storing the Compact Spare Tire and Tools” next in this section.

Cadillac SRX Owner Manual - 2011

Black plate (96,1)

10-96

Vehicle Care

Compact Spare Tire { WARNING Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.

If this vehicle has a compact spare tire, it was fully inflated when the vehicle was new; however, it can lose air after a time. Check the inflation pressure regularly. It should be 420 kPa (60 psi). After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inflated. The compact spare is made to perform well at speeds up to 105 km/h (65 mph) for distances up to 5 000 km (3,000 mi), so you can finish your trip and have the full-size

tire repaired or replaced at your convenience. Of course, it is best to replace the spare with a full-size tire as soon as possible. The spare tire will last longer and be in good shape in case it is needed again. Notice: When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails which can damage the tire, wheel and other parts of the vehicle. Do not use the compact spare on other vehicles. Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together. Notice: Tire chains will not fit the compact spare. Using them can damage the vehicle and can damage the chains too. Do not use tire chains on the compact spare.

Jump Starting For more information about the vehicle battery, see Battery on page 10‑30. If the vehicle battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.

{ WARNING

Batteries can hurt you. They can be dangerous because:

. They contain acid that can

burn you.

. They contain gas that can

explode or ignite.

. They contain enough electricity to burn you.

If you do not follow these steps exactly, some or all of these things can hurt you.

Cadillac SRX Owner Manual - 2011

Black plate (97,1)

Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. 1. Check the other vehicle. It must

have a 12-volt battery with a negative ground system. Notice: Only use a vehicle that has a 12-volt system with a negative ground for jump starting. If the other vehicle does not have a 12-volt system with a negative ground, both vehicles can be damaged.

2. Get the vehicles close enough

3. Turn off the ignition on both

Vehicle Care

10-97

vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlet. Turn off the radio and all lamps that are not needed. This will avoid sparks, helping save both batteries and the radio.

4. Open the hood on the

other vehicle and locate the positive (+) and negative (−) terminal locations on that vehicle. Open the hood on your vehicle and find the remote positive (+) and remote negative (−) jump starting terminals.

so the jumper cables can reach, but be sure the vehicles are not touching each other. If they are, it could cause a ground connection you do not want. You would not be able to start your vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake firmly on both vehicles involved in the jump start procedure. Put the transmission in P (Park) before setting the parking brake.

Notice: If the radio or other accessories are left on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle.

Cadillac SRX Owner Manual - 2011

Black plate (98,1)

10-98

Vehicle Care

To uncover the remote positive (+) terminal, lift open the access panel on the battery cover indicated by the (+) sign.

{ WARNING

An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.

{ WARNING

Using an open flame near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in

(Continued)

WARNING (Continued)

your new vehicle. But if a battery has filler caps, be sure the right amount of fluid is there. If it is low, add water to take care of that first. If you do not, explosive gas could be present. Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.

{ WARNING

Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.

Your vehicle is equipped with a remote positive (+) terminal (A) and a remote negative (−) terminal (B). The remote positive (+) terminal is located in the engine compartment on the driver side of the vehicle, above the rear of the battery. The remote negative (−) terminal is a stud located in the engine compartment on the driver side of the vehicle, on the front tie bar. See Engine Compartment Overview on page 10‑6 for more information on location.

Cadillac SRX Owner Manual - 2011

Black plate (99,1)

Vehicle Care

10-99

9. Connect the other end of the negative (−) cable away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less. Your vehicle has a remote (−) terminal for this purpose.

10. Now start the vehicle with

the good battery and run the engine for a while.

11. Try to start the vehicle that

had the dead battery. If it will not start after a few tries, it probably needs service.

5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could also be damaged. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative (−) will go to a heavy, unpainted metal engine part or to a remote negative (−) terminal if the vehicle has one. Do not connect positive (+) to negative (−) or you will get a short that would damage the battery and maybe other parts. Do not connect the negative (−) cable to the negative (−) terminal on the dead battery because this can cause sparks.

6. Connect the red positive (+)

cable to the positive (+) terminal on the vehicle with the dead battery. Use a remote positive (+) terminal if the vehicle has one.

7. Do not let the other end

touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.

8. Now connect the black

negative (−) cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative (−) cable does not go to the dead battery. It goes to a heavy, unpainted metal engine part or to a remote negative (−) terminal on the vehicle with the dead battery.

Cadillac SRX Owner Manual - 2011

Black plate (100,1)

10-100

Vehicle Care

Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.

To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black

negative (−) cable from the vehicle that had the dead battery.

2. Disconnect the black

negative (−) cable from the vehicle with the good battery.

3. Disconnect the red positive (+) cable from the vehicle with the good battery.

4. Disconnect the red positive (+)

cable from the other vehicle.

5. Close the access panel on the

battery cover, if applicable.

Jumper Cable Removal

A. Heavy, Unpainted Metal Engine

Part or Remote Negative (−) Terminal

B. Good Battery or Remote Positive (+) and Remote Negative (−) Terminals

C. Dead Battery or Remote

Positive (+) Terminal

Cadillac SRX Owner Manual - 2011

Black plate (101,1)

Vehicle Care

10-101

Towing

Towing the Vehicle Notice: To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Care must be taken with vehicles that have low ground clearance and/or special equipment. Always flatbed on a car carrier. Consult your dealer or a professional towing service if the disabled vehicle must be towed. See Roadside Service (U.S. and Canada) on page 13‑8 or Roadside Service (Mexico) on page 13‑11. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motor home, see “Recreational Vehicle Towing” in this section.

Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motor home. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground. Dolly towing is towing the vehicle with two wheels on the ground and two wheels up on a device known as a dolly. Here are some important things to consider before recreational vehicle towing: . What is the towing capacity

of the towing vehicle? Be sure to read the tow vehicle manufacturer's recommendations.

. What is the distance that will be travelled? Some vehicles have restrictions on how far and how long they can tow. Is the proper towing equipment going to be used? See your dealer or trailering professional for additional advice and equipment recommendations. Is the vehicle ready to be towed? Just as preparing the vehicle for a long trip, make sure the vehicle is prepared to be towed.

Cadillac SRX Owner Manual - 2011

Black plate (102,1)

10-102

Vehicle Care

Dinghy Towing Front-wheel‐drive and all-wheel-drive vehicles may be dinghy towed from the front. These vehicles can also be towed by placing them on a platform trailer with all four wheels off of the ground. For other towing options, see “Dolly Towing” following in this section. Vehicles with an 2.8 L V 6 engine can be dinghy towed only for service and are restricted to a maximum distance of 100 km (60 miles) and not to exceed 80 km/h (50 mph). Vehicles with the 3.0 L V 6 engine can be dinghy towed without distance restrictions. Notice: If 105 km/h (65 mph) is exceeded while towing the vehicle, it could be damaged. Never exceed 105 km/h (65 mph) while towing the vehicle.

For vehicles being dinghy towed, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes. This will ensure proper lubrication of transmission components.

To tow the vehicle from the front with all four wheels on the ground: 1. Position the vehicle that will

be towed and secure it to the towing vehicle.

2. Remove the shift lever boot by

pulling up on the rear of the trim plate.

Cadillac SRX Owner Manual - 2011

Black plate (103,1)

Once the destination has been reached: 1. Shift the vehicle to P (Park). 2. Reinstall the shift lever boot by

inserting the front edge and pressing the rear of the trim plate until it snaps into place.

3. Start the engine and let it idle for more than three minutes before driving the vehicle.

Notice: Too much or too little fluid can damage the transmission. Be sure that the transmission fluid is at the proper level before towing with all four wheels on the ground.

Vehicle Care

10-103

Notice: Do not tow a vehicle with the front drive wheels on the ground if one of the front tires is a compact spare tire. Towing with two different tire sizes on the front of the vehicle can cause severe damage to the transmission. Dolly Towing (All-Wheel‐Drive Vehicles) All-wheel‐drive vehicles should not be towed with two wheels on the ground. To properly tow these vehicles, they should be placed on a platform trailer with all four wheels off of the ground or dinghy towed from the front. See Dinghy Towing earlier in this section.

3. Use a small screw driver or tool

to press and hold the manual release button on the front right.

4. Put the vehicle in N (Neutral). Notice: If the vehicle is towed without performing each of the steps listed under “Dinghy Towing,” the automatic transmission could be damaged. Be sure to follow all steps of the dinghy towing procedure prior to and after towing the vehicle.

Cadillac SRX Owner Manual - 2011

Black plate (104,1)

10-104

Vehicle Care

Dolly Towing (Front-Wheel‐Drive Vehicles)

3. Set the parking brake. 4. Secure the vehicle to the dolly. 5. Follow the dolly manufacturer's

instructions for preparing the vehicle and dolly for towing. 6. Release the parking brake. Towing the Vehicle From the Rear

To tow the vehicle from the front with the rear wheels on the ground, do the following: 1. Put the front wheels on a dolly. 2. Move the shift lever to P (Park).

See Shifting Into Park on page 9‑23.

Notice: Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty. Never have the vehicle towed from the rear.

Cadillac SRX Owner Manual - 2011

Black plate (105,1)

Appearance Care

Exterior Care

Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing the Vehicle” later in this section. Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer. If the vehicle has a basecoat/ clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use

waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter.

Vehicle Care

10-105

Exterior painted surfaces are subject to aging, weather, and chemical fallout that can take their toll over a period of years. To keep the paint finish looking new, keep the vehicle garaged or covered whenever possible.

Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Wash with water or use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam, or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts.

Cadillac SRX Owner Manual - 2011

Black plate (106,1)

10-106

Vehicle Care

Washing the Vehicle To preserve the vehicle's finish, keep it clean by washing it often. Do not wash the vehicle in direct sunlight and use a car washing soap. Notice: Do not use cleaning agents that are petroleum based or that contain acid or abrasives, as they can damage the paint, metal, or plastic on the vehicle. Approved cleaning products can be obtained from your dealer. Follow all manufacturer directions regarding correct product usage, necessary safety precautions, and appropriate disposal of any vehicle care product. Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle. Check the cleaning product label. If it states that it

should not be used on plastic parts, do not use it on the vehicle or damage may occur and it would not be covered by the warranty. Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes could cause water to enter the vehicle. Avoid using high pressure washes closer than 30 cm (12 in) to the surface of the vehicle. Use of power washers exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals.

Notice: Conveyor systems on some automatic car washes could damage the vehicle. There may not be enough clearance for the undercarriage. Check with the car wash manager before using the automatic car wash. Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 11‑7.

Cadillac SRX Owner Manual - 2011

Black plate (107,1)

Wheels and Trim — Aluminum or Chrome The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft, clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft, clean towel. A wax may then be applied. Notice: Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash the chrome with soap and water after exposure. Notice: Do not use strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or

chrome-plated wheels, because the surface could be damaged. The repairs would not be covered by the vehicle warranty. Use only approved cleaners on aluminum or chrome-plated wheels. Notice: Never drive a vehicle that has aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes, as this could cause damage. The repairs would not be covered by the vehicle warranty. Notice: Driving the vehicle through an automatic car wash that has silicone carbide tire cleaning brushes, could damage the aluminum or chrome-plated wheels. The repairs would not be covered by the vehicle warranty. Never drive a vehicle that has aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes.

Vehicle Care

10-107

Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean the rubber blades using a lint‐free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking. Replace the wiper blades if they are worn or damaged. Wipers can be damaged by: . Extreme dusty conditions . Sand and salt . Heat and sun . Snow and ice, without proper

removal

Cadillac SRX Owner Manual - 2011

Black plate (108,1)

10-108

Vehicle Care

Tires Use a stiff brush with tire cleaner to clean the tires. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle. Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty.

Finish Damage Any stone chips, fractures, or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer. Larger areas of finish damage can be corrected in your dealer's body and paint shop. Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection.

At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this. Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface.

Cadillac SRX Owner Manual - 2011

Black plate (109,1)

Interior Care The interior will continue to look its best if it is cleaned often. Dust and dirt can accumulate on the upholstery and cause damage to the carpet, fabric, leather, and plastic surfaces. Stains should be removed quickly as extreme heat could cause them to set rapidly. Lighter colored interiors may require more frequent cleaning. Newspapers and garments that can transfer color to home furnishings can also transfer color to the interior. Remove dust from small buttons and knobs with a small brush with soft bristles.

Your dealer has products for cleaning the interior. When cleaning the interior, only use cleaners specifically designed for the surfaces that are being cleaned. Permanent damage can result from using cleaners on surfaces for which they were not intended. Apply the cleaner directly to the cleaning cloth to prevent over-spray. Remove any accidental over-spray from other surfaces immediately. Notice: Using abrasive cleaners when cleaning glass surfaces on the vehicle, could scratch the glass and/or cause damage to the rear window defogger. When cleaning the glass on the vehicle, use only a soft cloth and glass cleaner.

Vehicle Care

10-109

Cleaners can contain solvents that can become concentrated in the interior. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning the interior, maintain adequate ventilation by opening the doors and windows. Do not clean the interior using the following cleaners or techniques: . Never use a knife or any other

sharp object to remove a soil from any interior surface.

. Never use a stiff brush. It can

cause damage.

. Never apply heavy pressure or

rub aggressively with a cleaning cloth. Use of heavy pressure can damage the interior and does not improve the effectiveness of soil removal.

Cadillac SRX Owner Manual - 2011

Black plate (110,1)

10-110

Vehicle Care

. Avoid laundry detergents

or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per 3.78 L (1 gal) of water is a good guide. Use only mild, neutral-pH soaps.

. Do not heavily saturate the upholstery while cleaning.

. Cleaners that contain solvents

can damage the interior.

Fabric/Carpet Use a vacuum cleaner with a soft brush attachment to remove dust and loose dirt. A canister vacuum with rotating brushes in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda. Before cleaning, gently remove as much of the soil as possible using one of the following techniques:

For liquids: gently blot the remaining soil with a paper towel. Allow the soil to absorb into the paper towel until no more can be removed. For solid dry soils: remove as much as possible and then vacuum.

To clean: 1. Saturate a lint-free, clean white

cloth with water or club soda.

2. Remove excess moisture. 3. Start on the outside edge of the

soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.

4. Continue to gently rub the

5.

soiled area. If the soil is not completely removed, use a mild soap solution and repeat the cleaning process with plain water.

Cadillac SRX Owner Manual - 2011

Black plate (111,1)

If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. Test a small hidden area for colorfastness before using a commercial upholstery cleaner or spot lifter. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. A paper towel can be used to blot excess moisture from the fabric or carpet after the cleaning process. Leather Leather, and lighter colored leather in particular, will need more frequent cleaning to prevent the buildup of dust, dirt, and colors transferred from other items so that these do not become permanent stains.

To remove dust, a soft cloth dampened with water can be used. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Your dealer has a GM approved leather cleaner available that provides superior cleaning performance when used regularly on finished automotive leathers. Allow the leather to dry naturally. Do not use heat, steam, spot lifters or spot removers, or shoe polish on leather. Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of the leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean the interior because they can alter the appearance by increasing the gloss in a non-uniform manner.

Vehicle Care

10-111

Instrument Panel, Vinyl, and Other Plastic Surfaces To remove dust, a soft cloth dampened with water can be used. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of the interior and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean the interior because they can alter the appearance by increasing the gloss in a non-uniform manner.

Cadillac SRX Owner Manual - 2011

Black plate (112,1)

10-112

Vehicle Care

Some commercial products may increase gloss on the instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Notice: Air fresheners contain solvents that may cause damage to plastics and painted surfaces. Follow the manufacturer’s instructions when using air fresheners in the vehicle. If air freshener comes in contact with paint or a plastic surface, blot immediately with a soft cloth. Damage caused by using air fresheners would not be covered by the vehicle warranty.

Care of Safety Belts Keep belts clean and dry. { WARNING

Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.

Floor Mats

{ WARNING

If a floor mat is the wrong size or is not properly installed, it can interfere with the accelerator pedal and/or brake pedal. Interference with the pedals can cause unintended acceleration and/or increased stopping distance which can cause a crash and injury. Make sure the floor mat does not interfere with the accelerator or brake pedal.

Cadillac SRX Owner Manual - 2011

Black plate (113,1)

Use the following guidelines for proper floor mat usage:

The original equipment floor mats were designed for your vehicle. If the floor mats need replacing, it is recommended that GM certified floor mats be purchased. Non-GM floor mats may not fit properly and may interfere with the accelerator or brake pedal. Always check that the floor mats do not interfere with the pedals.

. Use the floor mat with the

correct side up. Do not turn it over.

. Do not place anything on top of

the driver side floor mat.

. Use only a single floor mat on

the driver side.

. Do not place one floor mat on

top of another.

Removing and Replacing the Floor Mats The drivers side floor mat is held in place by two button-type retainers. The passenger side floor mat is held in place by one button-type retainer.

Vehicle Care

10-113

2. Reinstall by lining up the floor mat retainer openings over the carpet retainers and snapping into position.

3. Make sure the floor mat is

properly secured and verify that it does not interfere with the accelerator or brake pedal.

1. Pull up on the rear of the floor

mat to unlock each retainer and remove.

Cadillac SRX Owner Manual - 2011

Black plate (114,1)

10-114

Vehicle Care

2 NOTES

Cadillac SRX Owner Manual - 2011

Black plate (1,1)

Service and Maintenance

General Information

General Information . . . . . . . . . . 11-1

Scheduled Maintenance

Scheduled Maintenance . . . . . 11-2

Recommended Fluids, Lubricants, and Parts

Recommended Fluids and

Lubricants . . . . . . . . . . . . . . . . . . 11-7

Maintenance Replacement

Parts . . . . . . . . . . . . . . . . . . . . . . . 11-9

Maintenance Records

Maintenance Records . . . . . . 11-10

Service and Maintenance

11-1

General Information Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty. As the vehicle owner, you are responsible for the scheduled maintenance in this section. We recommend having your dealer perform these services. Proper vehicle maintenance helps to keep the vehicle in good working condition, improves fuel economy, and reduces vehicle emissions for better air quality.

Because of all the different ways people use vehicles, maintenance needs vary. The vehicle might need more frequent checks and services. Please read the information under Scheduled Maintenance. To keep the vehicle in good condition, see your dealer. The maintenance schedule is for vehicles that: . Carry passengers and cargo within recommended limits on the Tire and Loading Information label. See Vehicle Load Limits on page 9‑12.

. Are driven on reasonable road

surfaces within legal driving limits.

. Use the recommended fuel. See Recommended Fuel on page 9‑48.

Cadillac SRX Owner Manual - 2011

Black plate (2,1)

11-2

Service and Maintenance

{ WARNING

Performing maintenance work can be dangerous. Some jobs can cause serious injury. Perform maintenance work only if you have the required know-how and the proper tools and equipment. If in doubt, see your dealer to have a qualified technician do the work. See Doing Your Own Service Work on page 10‑4.

At your dealer, you can be certain that you will receive the highest level of service available. Your dealer has specially trained service technicians, uses genuine replacement parts, as well as, up‐to‐date tools and equipment to ensure fast and accurate diagnostics.

The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 11‑7 and Maintenance Replacement Parts on page 11‑9. We recommend the use of genuine parts from your dealer.

Rotation of New Tires To maintain ride, handling, and performance of the vehicle, it is important that the first rotation service for new tires be performed. Tires should be rotated every 12 000 km/7,500 miles. See Tire Rotation on page 10‑71.

Scheduled Maintenance

When the Change Engine Oil Soon Message Displays Change engine oil and filter. See Engine Oil on page 10‑10. An Emission Control Service. When the CHANGE ENGINE OIL SOON message displays, service is required for the vehicle as soon as possible, within the next 1 000 km/600 miles. If driving under the best conditions, the engine oil life system might not indicate the need for vehicle service for more than a year. The engine oil and filter must be changed at least once a year and the oil life system must be reset. Your dealer has trained service technicians who will perform this work and reset the system.

Cadillac SRX Owner Manual - 2011

Black plate (3,1)

Service and Maintenance

11-3

If the engine oil life system is reset accidentally, service the vehicle within 5 000 km/3,000 miles since the last service. Reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 10‑14. Every Engine Oil Change . Change engine oil and

filter. Reset oil life system. See Engine Oil on page 10‑10
and Engine Oil Life System on page 10‑14. An Emission Control Service.

. Engine coolant level check.

See Engine Coolant on page 10‑20.

. Engine cooling system

inspection. Visual inspection of hoses, pipes, fittings, and clamps and replacement, if needed.

. Windshield washer fluid level check. See Washer Fluid on page 10‑26.

. Windshield wiper blade

inspection for wear, cracking, or contamination and windshield and wiper blade cleaning, if contaminated. See Exterior Care on page 10‑105. Worn or damaged wiper blade replacement. See Wiper Blade Replacement on page 10‑33. Tire inflation pressures check. See Tire Pressure on page 10‑63. Tire wear inspection. See Tire Inspection on page 10‑71.

. Rotate tires if necessary.

See Tire Rotation on page 10‑71.

Fluids visual leak check (or every 12 months, whichever occurs first). A leak in any system must be repaired and the fluid level checked.

. Engine air cleaner filter

inspection. See Engine Air Cleaner/Filter on page 10‑16.

. Brake system inspection

(or every 12 months, whichever occurs first).

. Steering and suspension

inspection. Visual inspection for damaged, loose, or missing parts or signs of wear.

Cadillac SRX Owner Manual - 2011

Black plate (4,1)

11-4

Service and Maintenance

. Body hinges and latches, key lock cylinders, folding seat hardware, and sunroof (if equipped) lubrication. See Recommended Fluids and Lubricants on page 11‑7. More frequent lubrication may be required when the vehicle is exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth makes them last longer, seal better, and not stick or squeak.

. Restraint system component

check. See Safety System Check on page 3‑29. Fuel system inspection for damage or leaks.

. Exhaust system and nearby heat

shields inspection for loose or damaged components.

Additional Required Services

Every 12 000 km/7,500 Miles . Rotate tires. Tires should

be rotated every 12 000 km/ 7,500 miles. See Tire Rotation on page 10‑71.

At Each Fuel Stop . Engine oil level check.

See Engine Oil on page 10‑10.

. Engine coolant level check.

See Engine Coolant on page 10‑20.

. Windshield washer fluid level check. See Washer Fluid on page 10‑26.

Once a Month

Tire inflation check. See Tire Pressure on page 10‑63. Tire wear inspection. See Tire Inspection on page 10‑71.

. Sunroof track and seal inspection, if equipped. See Sunroof on page 2‑27.

Once a Year . See Starter Switch Check on

page 10‑31.

. See Automatic Transmission

Shift Lock Control Function Check on page 10‑31.

. See Ignition Transmission Lock

Check on page 10‑32.

. See Park Brake and P (Park)

Mechanism Check on page 10‑32.

. Accelerator pedal check for

damage, high effort, or binding. Replace if needed. If the vehicle has a Tire Sealant and Compressor Kit, check the sealant expiration date printed on the instruction label of the kit. See Tire Sealant and Compressor Kit on page 10‑81.

Cadillac SRX Owner Manual - 2011

Black plate (5,1)

Service and Maintenance

11-5

First Engine Oil Change After Every 80 000 km/50,000 Miles . Engine air cleaner filter

replacement. See Engine Air Cleaner/Filter on page 10‑16. . Automatic transmission fluid change (severe service) for vehicles mainly driven in heavy city traffic in hot weather, in hilly or mountainous terrain, when frequently towing a trailer, or used for taxi, police, or delivery service. See Automatic Transmission Fluid on page 10‑16.

. All‐wheel drive only: Transfer

case fluid change (severe service) for vehicles mainly driven when frequently towing a trailer, or used for taxi, police, or delivery service. Check vent hose at transfer case for kinks and proper installation. Check to be sure vent hose is unobstructed, clear, and free of debris. During any maintenance, if a power washer is used to clean mud and dirt from the underbody, care should be taken to not directly spray the transfer case output seals. High pressure water can overcome the seals and contaminate the transfer case fluid. Contaminated fluid will decrease the life of the transfer case and should be replaced.

. Underbody flushing service. . Hood/Decklid/Liftgate/Liftglass

Support Gas Strut Service: Visually inspect gas strut, if equipped, for signs of wear, cracks, or other damage. Check the hold open ability of the gas strut. Contact your dealer if service is required.

First Engine Oil Change After Every 40 000 km/25,000 Miles . Passenger compartment

air filter replacement (or every 24 months, whichever occurs first). More frequent replacement may be needed if you drive in areas with heavy traffic, areas with poor air quality, or areas with high dust levels. Replacement may also be needed if you notice reduced air flow, windows fogging up, or odors. Your dealer can help you determine when it is the right time to replace the filter.

Cadillac SRX Owner Manual - 2011

Black plate (6,1)

11-6

Service and Maintenance

. Evaporative control system

inspection. Check all fuel and vapor lines and hoses for proper hook‐up, routing, and condition. Check that the purge valve, if the vehicle has one, works properly. Replace as needed. An Emission Control Service. The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle's useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.

First Engine Oil Change After Every 160 000 km/100,000 Miles . Automatic transmission fluid

change (normal service). See Automatic Transmission Fluid on page 10‑16.

. All‐wheel drive only: Transfer

case fluid change (normal service). Check vent hose at transfer case for kinks and proper installation. Check to be sure vent hose is unobstructed, clear, and free of debris. During any maintenance, if a power washer is used to clean mud and dirt from the underbody, care should be taken to not directly spray the transfer case output seals. High pressure water can overcome the seals and contaminate the transfer case fluid. Contaminated fluid will decrease the life of the transfer case and should be replaced.

. Spark plug replacement and spark plug wires inspection. An Emission Control Service.

First Engine Oil Change After Every 240 000 km/150,000 Miles . Engine cooling system drain,

flush, and refill (or every five years, whichever occurs first). See Cooling System on page 10‑19. An Emission Control Service.

. Engine drive belts inspection for fraying, excessive cracks, or obvious damage (or every 10 years, whichever occurs first). Replace, if needed.

Cadillac SRX Owner Manual - 2011

Black plate (7,1)

Service and Maintenance

11-7

Recommended Fluids, Lubricants, and Parts

Recommended Fluids and Lubricants

Usage

Engine Oil

Engine Coolant

Hydraulic Brake System

Windshield Washer

Hydraulic Power Steering System

Automatic Transmission

(3.0L V6 Engine)

Fluid/Lubricant

The engine requires engine oil approved to the dexos specification. Oils meeting this specification can be identified with the dexos certification mark. Look for and use only an engine oil that displays the dexos certification mark of the proper viscosity grade. See Engine Oil on page 10‑10. 50/50 mixture of clean, drinkable water and use only DEX-COOL Coolant. See Engine Coolant on page 10‑20. DOT 3 Hydraulic Brake Fluid (GM Part No. 88863461, in Canada 88863462). Optikleen® Washer Solvent. DEXRON®-VI Automatic Transmission Fluid.

DEXRON®-VI Automatic Transmission Fluid.

Cadillac SRX Owner Manual - 2011

Black plate (8,1)

11-8

Service and Maintenance

Usage

Automatic Transmission

(2.8L V6 Engine)

Chassis Lubrication

Key Lock Cylinders

Fluid/Lubricant

AW‐1 Automatic Transmission Fluid (GM Part No. 19256039, in Canada 19256040). Chassis Lubricant (GM Part No. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Multi-Purpose Lubricant, Superlube (GM Part No. 12346241, in Canada 10953474).

Hood Latch Assembly, Secondary Latch, Pivots, Spring Anchor, and

Release Pawl

Hood, Door, and Folding Seat Hinges

Power Liftgate Actuator Ball Joint

Weatherstrip Conditioning

Lubriplate Lubricant Aerosol (GM Part No. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.

Multi-Purpose Lubricant, Superlube (GM Part No. 12346241, in Canada 10953474). Multi-Purpose Lubricant (GM Part No. 89021668, in Canada 89021674). Weatherstrip Lubricant (GM Part No. 3634770, in Canada 10953518) or Dielectric Silicone Grease (GM Part No. 12345579, in Canada 992887).

Cadillac SRX Owner Manual - 2011

Black plate (9,1)

Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer.

Part

GM Part Number

ACDelco Part Number

Service and Maintenance

11-9

Engine Air Cleaner/Filter Engine Oil Filter

2.8L V6 Engine 3.0L V6 Engine

Passenger Compartment Air Filter Element Spark Plugs

2.8L V6 Engine 3.0L V6 Engine

Wiper Blades

Driver Side – 65.0 cm (25.6 in) Passenger Side – 42.5 cm (16.7 in) Rear – 30.0 cm (11.8 in)

20897358

12593333
89017525
13271191

12622561
12622561

25979378
25979379
20825882

A3147C

PF457G

PF63
CF176

41–109
41–109

—

—

—

Cadillac SRX Owner Manual - 2011

Black plate (10,1)

11-10

Service and Maintenance

Maintenance Records After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts.

Maintenance Record

Date

Odometer Reading

Serviced By

Maintenance Stamp

Services Performed

Cadillac SRX Owner Manual - 2011

Black plate (11,1)

Date

Odometer Reading

Serviced By

Maintenance Stamp

Services Performed

Maintenance Record (cont.)

Service and Maintenance

11-11

Cadillac SRX Owner Manual - 2011

Black plate (12,1)

11-12

Service and Maintenance

Date

Odometer Reading

Serviced By

Maintenance Stamp

Services Performed

Maintenance Record (cont.)

Cadillac SRX Owner Manual - 2011

Black plate (1,1)

Technical Data

Vehicle Identification

Vehicle Identification

Vehicle Identification

Number (VIN) . . . . . . . . . . . . . . 12-1

Service Parts Identification

Label . . . . . . . . . . . . . . . . . . . . . . . 12-1

Vehicle Data

Capacities and

Specifications . . . . . . . . . . . . . . 12-2
Engine Drive Belt Routing . . . 12-4

Vehicle Identification Number (VIN)

This legal identifier is in the front corner of the instrument panel, on the left side of the vehicle. It can be seen through the windshield from outside. The VIN also appears on the Vehicle Certification and Service Parts labels and certificates of title and registration.

Technical Data

12-1

Engine Identification The eighth character in the VIN is the engine code. This code identifies the vehicle's engine, specifications, and replacement parts. See “Engine Specifications” under Capacities and Specifications on page 12‑2 for the vehicle's engine code.

Service Parts Identification Label This label, on the inside of the rear side cargo management cover, has the following information: . Vehicle Identification

Number (VIN).

. Model designation. . Paint information. . Production options and special

equipment.

Do not remove this label from the vehicle.

Cadillac SRX Owner Manual - 2011

Black plate (2,1)

12-2

Technical Data

Vehicle Data

Capacities and Specifications

Application

Air Conditioning Refrigerant R134a

Engine Cooling System

2.8L V6 Engine 3.0L V6 Engine

Engine Oil with Filter

2.8L V6 Engine 3.0L V6 Engine

Fuel Tank

Capacities

Metric

English

For the air conditioning system refrigerant charge amount, see the refrigerant label located under the

hood. See your dealer for more information.

12.4 L 11.9 L

5.7 L 5.7 L 79.5 L

13.1 qt 12.6 qt

6.0 qt 6.0 qt 21.0 gal

Cadillac SRX Owner Manual - 2011

Black plate (3,1)

Technical Data

12-3

Capacities

Metric

English

—

9.0 L

—

9.5 qt 110 ft lb

Application

Transmission Fluid

2.8L V6 6–Speed Automatic (Transmission Requires No Fluid Replacement) 3.0L V6 6–Speed Automatic* (Drain and Refill)

Wheel Nut Torque *See Automatic Transmission Fluid on page 10‑16 for information on checking fluid level. All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual. Recheck fluid level after filling.

150 Y

Engine Specifications

Engine