Download PDF Manual

temperature gauge on the instrument panel cluster. See Engine Coolant Temperature Gauge on page 5‑15. The vehicle may also display an ENGINE OVERHEATED IDLE ENGINE and ENGINE OVERHEATED STOP ENGINE message in the Driver Information Center (DIC). See Engine Cooling System Messages on page 5‑33. You may decide not to lift the hood when this warning appears, but instead get service help right away. See Roadside Assistance Program (U.S. and Canada) on page 13‑8
or Roadside Assistance Program (Mexico) on page 13‑10.


5. Fill the coolant recovery tank to


the FULL COLD mark.


6. Reinstall the cap on the coolant


recovery tank but leave the radiator pressure cap off.


7. Start the engine and let it run until the upper radiator hose feels warm. Any time during this procedure, watch out for the engine cooling fans.


Buick Enclave Owner Manual - 2012


Black plate (19,1)


If Steam Is Coming from the Engine Compartment { WARNING


Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.


(Continued)


Vehicle Care


10-19


WARNING (Continued)


If you keep driving when the vehicles engine is overheated, the liquids in it can catch fire. You or others could be badly burned. Stop the engine if it overheats, and get out of the vehicle until the engine is cool. See Overheated Engine Protection Operating Mode on page 10‑20 for information on driving to a safe place in an emergency.


If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced. Notice: Engine damage from running the engine without coolant is not covered by the warranty. Notice: If the engine catches fire while driving with no coolant, the vehicle can be badly damaged. The costly repairs would not be covered by the vehicle warranty. See Overheated Engine Protection Operating Mode on page 10‑20 for information on driving to a safe place in an emergency.


Buick Enclave Owner Manual - 2012


Black plate (20,1)


10-20


Vehicle Care


If No Steam Is Coming from the Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: . Climbs a long hill on a hot day . Stops after high-speed driving Idles for long periods in traffic Tows a trailer


If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest


temperature and to the highest fan speed. Open the windows as necessary.


3.


If in a traffic jam, shift to N (Neutral); otherwise, shift to the highest gear while driving — D (Drive) or L (Low). If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you. If the warning does not come back on, continue to drive normally. If the warning continues, pull over, stop, and park the vehicle right away. If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down. Also, see “Overheated Engine Protection Operating Mode” next in this section.


Overheated Engine Protection Operating Mode This emergency operating mode lets the vehicle be driven to a safe place in an emergency situation. If an overheated engine condition exists, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage. In this mode, there is a significant loss in power and engine performance. The temperature gauge indicates an overheat condition exists. Driving extended distances and/or towing a trailer in the overheat protection mode should be avoided.


Buick Enclave Owner Manual - 2012


Black plate (21,1)


Notice: After driving in the overheated engine protection operating mode, to avoid engine damage, allow the engine to cool before attempting any repair. The engine oil will be severely degraded. Repair the cause of coolant loss, change the oil and reset the oil life system. See Engine Oil on page 10‑8.


Power Steering Fluid


The power steering fluid reservoir is located under the engine cover on the passenger side of the vehicle. See Engine Compartment Overview on page 10‑6 for reservoir location.


When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. How to Check Power Steering Fluid To check the power steering fluid: 1. Turn the key off and let the


engine compartment cool down.


2. Remove the engine cover.


See Engine Cover on page 10‑7.


3. Wipe the cap and the top of the


reservoir clean.


4. Unscrew the cap and wipe the


dipstick with a clean rag.


Vehicle Care


10-21


5. Replace the cap and completely


tighten it.


6. Remove the cap again and look at the fluid level on the dipstick.


The fluid level should be somewhere between the MAX and MIN line on the dipstick in room temperature. If the fluid is on or below the MIN line, add fluid close to the MAX Line. What to Use To determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 11‑12. Always use the proper fluid. Notice: Use of the incorrect fluid may damage the vehicle and the damages may not be covered by the vehicle's warranty. Always use the correct fluid listed in Recommended Fluids and Lubricants on page 11‑12.


Buick Enclave Owner Manual - 2012


Black plate (22,1)


10-22


Vehicle Care


Washer Fluid


What to Use When adding windshield washer fluid, be sure to read the manufacturer's instructions before use. If the vehicle will be operating in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Adding Washer Fluid When the windshield washer fluid reservoir is low, a WASHER FLUID LOW ADD FLUID message will be displayed on the Driver Information Center (DIC). See Washer Fluid Messages on page 5‑40 for more information.


Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 10‑6 for reservoir location. Notice


. When using concentrated


washer fluid, follow the manufacturer's instructions for adding water.


. Do not mix water with


ready-to-use washer fluid. Water can cause the solution


to freeze and damage the washer fluid tank and other parts of the washer system. Also, water does not clean as well as washer fluid.


. Fill the washer fluid tank


only three-quarters full when it is very cold. This allows for fluid expansion if freezing occurs, which could damage the tank if it is completely full.


. Do not use engine coolant


(antifreeze) in the windshield washer. It can damage the windshield washer system and paint.


Buick Enclave Owner Manual - 2012


Black plate (23,1)


Brakes This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.


{ WARNING


The brake wear warning sound means that soon the brakes will not work well. That could lead to a crash. When the brake wear warning sound is heard, have the vehicle serviced.


Notice: Continuing to drive with worn-out brake pads could result in costly brake repair.


Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with the brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications in Capacities and Specifications on page 12‑2. Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required.


Vehicle Care


10-23


Brake Adjustment Every time the brakes are applied, with or without the vehicle moving, the brakes adjust for wear. Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced, be sure to get new, approved replacement parts. If this is not done, the brakes might not work properly. For example, installing disc brake pads that are wrong for the vehicle, can change the balance between the front and rear brakes — for the worse. The braking performance expected can change in many other ways if the wrong replacement brake parts are installed.


Buick Enclave Owner Manual - 2012


Black plate (24,1)


10-24


Vehicle Care


Brake Fluid


The brake master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. See Engine Compartment Overview on page 10‑6 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down:


The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up.


. A fluid leak in the brake


hydraulic system can also cause a low fluid level. Have the brake hydraulic system fixed, since a leak means that sooner or later the brakes will not work well.


Do not top off the brake fluid. Adding fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as necessary, only when work is done on the brake hydraulic system.


{ WARNING


If too much brake fluid is added, it can spill on the engine and burn, if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake fluid only when work is done on the brake hydraulic system.


When the brake fluid falls to a low level, the brake warning light comes on. See Brake System Warning Light on page 5‑22.


What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 11‑12. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.


{ WARNING With the wrong kind of fluid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake fluid.


Buick Enclave Owner Manual - 2012


Black plate (25,1)


Vehicle Care


10-25


Infrequent Usage: Remove the black, negative (−) cable from the battery to keep the battery from running down. Extended Storage: Remove the black, negative (−) cable from the battery or use a battery trickle charger.


All-Wheel Drive It is not necessary to check the all–wheel drive lubricant levels. A fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to the dealer as soon as possible.


Notice


. Using the wrong fluid


can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid.


. If brake fluid is spilled on the


vehicle's painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle. If you do, wash it off immediately.


Battery Refer to the replacement number on the original battery label when a new battery is needed.


{ WARNING


Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.


Vehicle Storage


{ WARNING


Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 10‑79 for tips on working around a battery without getting hurt.


Buick Enclave Owner Manual - 2012


Black plate (26,1)


10-26


Vehicle Care


Starter Switch Check


{ WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.


1. Before starting this check, be


sure there is enough room around the vehicle.


2. Firmly apply both the parking brake and the regular brake. See Parking Brake on page 9‑31. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.


3. Try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service.


Automatic Transmission Shift Lock Control Function Check


{ WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.


1. Before starting this check, be


sure there is enough room around the vehicle. It should be parked on a level surface.


2. Firmly apply the parking


brake. See Parking Brake on page 9‑31. Be ready to apply the regular brake immediately if the vehicle begins to move.


3. With the engine off, turn the


ignition on, but do not start the engine. Without applying the regular brake, try to move the shift lever out of P (Park) with normal effort. If the shift lever moves out of P (Park), contact your dealer for service.


Buick Enclave Owner Manual - 2012


Black plate (27,1)


Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position.


The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). The ignition key should come out only in LOCK/OFF.


Contact your dealer if service is required.


Park Brake and P (Park) Mechanism Check { WARNING


When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front


(Continued)


WARNING (Continued)


of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.


Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.


To check the parking brake's holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only. To check the P (Park) mechanism's holding ability: With the engine running, shift to P (Park). Then release the parking brake followed by the regular brake.


Contact your dealer if service is required.


Vehicle Care


10-27


Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Maintenance Schedule on page 11‑2 for more information. Replacement blades come in different types and are removed in different ways. To replace the wiper blade assembly: 1. Pull the windshield wiper arm


away from the windshield.


2. Press the button in the middle of the wiper arm connector and pull the wiper blade away from the arm connector. Install the new wiper blade and make sure the wiper blade locks into place.


3.


Buick Enclave Owner Manual - 2012


Black plate (28,1)


10-28


Vehicle Care


For the proper size and type see Maintenance Replacement Parts on page 11‑14. Backglass Wiper Blade To replace the backglass wiper blade: 1. Pull the wiper blade assembly


away from the backglass. The backglass wiper blade will not lock in a vertical position so care should be used when pulling it away from the vehicle.


2. Rotate the wiper blade


assembly, hold the wiper arm in position, and push the blade away from the wiper arm.


3. Replace the wiper blade. 4. Return the wiper arm and blade assembly to the rest position on the glass.


Windshield Replacement The vehicle is equipped with an acoustic windshield. If you ever have to have the windshield replaced be sure to get an acoustic windshield so you will continue to have the benefits an acoustic windshield can provide.


Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However, if your vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if oncoming drivers flash their high-beam headlamps at you (for vertical aim). If the headlamps need to be re-aimed, it is recommended that you take the vehicle to your dealer for service.


Buick Enclave Owner Manual - 2012


Black plate (29,1)


Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 10‑30. For any bulb‐changing procedure not listed in this section, contact your dealer.


Halogen Bulbs


{ WARNING


Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.


High Intensity Discharge (HID) Lighting


{ WARNING


The low beam high intensity discharge lighting system operates at a very high voltage. If you try to service any of the system components, you could be seriously injured. Have your dealer or a qualified technician service them.


After an HID headlamp bulb has been replaced, the beam might be a slightly different shade than it was originally. This is normal.


Vehicle Care


10-29


Taillamps, Turn Signal, Sidemarker, and Stoplamps


A. Taillamp B. Sidemarker Lamp To replace one of these bulbs: 1. Open the liftgate. See Liftgate


on page 2‑10.


2. Remove the black cuff from


the lamp assembly by pulling rearward from the top to unfasten it from the snap tabs.


Buick Enclave Owner Manual - 2012


Black plate (30,1)


10-30


Vehicle Care


3. Remove the two hex nuts


holding the taillamp assembly in place.


4. Pull out the taillamp assembly. 5. Turn the bulb socket


counterclockwise and pull it straight out to remove it.


6. Replace the bulb. 7. Reverse Steps 3 through 5 to


reinstall the taillamp assembly. When reinstalling the taillamp assembly, the pin on the taillamp assembly must line up and be inserted correctly into the opening.


8. Replace the black cuff over the


lamp assembly by pushing it into the snap tabs.


License Plate Lamp To replace one of these bulbs: 1. Remove the two screws holding each of the license plate lamps to the liftgate trim.


2. Turn and pull the license plate


lamp forward through the liftgate trim opening.


3. Turn the bulb socket


counterclockwise and pull the bulb straight out of the socket. Install the new bulb.


4. 5. Reverse Steps 1 through 3 to


reinstall the license plate lamp.


Replacement Bulbs


Exterior Lamp


License Plate Lamp Rear Sidemarker Lamp Rear Turn Signal and Taillamps


Bulb


Number 194LL


194LL


7443


(W21/5W)


For replacement bulbs not listed here, contact your dealer.


Buick Enclave Owner Manual - 2012


Black plate (31,1)


Electrical System


High Voltage Devices and Wiring


{ WARNING Exposure to high voltage can cause shock, burns, and even death. The high voltage components in the vehicle can only be serviced by technicians with special training. High voltage components are identified by labels. Do not remove, open, take apart, or modify these components. High voltage cable or wiring has orange covering. Do not probe, tamper with, cut, or modify high voltage cable or wiring.


Electrical System Overload The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the chance of circuit overload and fire caused by electrical problems. Fuses and circuit breakers protect power devices in the vehicle. Replace a bad fuse with a new one of the identical size and rating. If there is a problem on the road and a fuse needs to be replaced, the same amperage fuse can be borrowed. Choose some feature of the vehicle that is not needed to use and replace it as soon as possible.


Vehicle Care


10-31


Headlamp Wiring An electrical overload may cause the lamps to go on and off, or in some cases to remain off. Have the headlamp wiring checked right away if the lamps go on and off or remain off. Windshield Wipers If the wiper motor overheats due to heavy snow or ice, the windshield wipers will stop until the motor cools and will then restart. Although the circuit is protected from electrical overload, overload due to heavy snow or ice may cause wiper linkage damage. Always clear ice and heavy snow from the windshield before using the windshield wipers. If the overload is caused by an electrical problem and not snow or ice, be sure to get it fixed.


Buick Enclave Owner Manual - 2012


Black plate (32,1)


10-32


Vehicle Care


Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating. Fuses of the same amperage can be temporarily borrowed from another fuse location, if a fuse goes out. Replace the fuse as soon as you can.


Engine Compartment Fuse Block The underhood fuse block is located in the engine compartment, on the passenger side of the vehicle.


Notice: Spilling liquid on any electrical component on the vehicle may damage it. Always keep the covers on any electrical component. To remove fuses, hold the end of the fuse between your thumb and index finger and pull straight out.


Lift the cover for access to the fuse/relay block.


Buick Enclave Owner Manual - 2012


Black plate (33,1)


Vehicle Care


10-33


The vehicle may not be equipped with all of the fuses, relays, and features shown.


Fuses


Usage


ABS MTR


A/C CLTCH Air Conditioning


Clutch Antilock Brake System (ABS) Motor Adaptive Forward Lighting System Airbag System AUX POWER Auxiliary Power


AIRBAG


AFS


AUX


VAC PUMP


AWD


BATT 1
BATT 2
BATT 3
CIGAR


LIGHTER


Auxiliary Vacuum Pump All-Wheel-Drive System Battery 1
Battery 2
Battery 3


Cigarette Lighter


Buick Enclave Owner Manual - 2012


Black plate (34,1)


10-34


Vehicle Care


Usage


Fuses


Usage


Fuses


Usage


LT HI BEAM Left High-Beam


RT HI BEAM Right High‐Beam


Fuses


ECM


ECM 1


Engine Control Module Engine Control Module 1


EMISSION 1 Emission 1
EMISSION 2 Emission 2
EVEN COILS Even Injector Coils


FAN 1
FAN 2


Cooling Fan 1
Cooling Fan 2


FOG LAMP Fog Lamps


FSCM


HORN


HTD MIR


HUMIDITY/


MAF


HVAC BLWR


Fuel System Control Module Horn Heated Outside Rearview Mirror Humidity Sensor/ MAF Sensor Heating, Ventilation and Air Conditioning Blower


LT LO BEAM


LT PRK


LT TRLR STOP/TRN


Headlamp Left Low‐Beam Headlamp Left Parking Lamp Trailer Left Stoplamp and Turn Signal


ODD COILS Odd Injector Coils Powertrain Control Module Ignition PWR L/GATE Power Liftgate


PCM IGN


PWR


OUTLET


REAR


CAMERA


RR APO


Power Outlet


Rear Vision Camera Rear Accessory Power Outlet


RR DEFOG Rear Defogger


RR HVAC


Rear Climate Control System


RT LO BEAM


RT PRK


RT TRLR STOP/TRN


RVC SNSR


Headlamp Right Low‐Beam Headlamp Right Parking Lamp Trailer Right Stoplamp and Turn Signal Regulated Voltage Control Sensor


S/ROOF/


SUNSHADE


Sunroof


SERVICE SPARE STOP LAMPS


(China Only)


STRTR


TCM


Service Repair Spare


Stoplamps (China Only)


Starter Transmission Control Module


Buick Enclave Owner Manual - 2012


Black plate (35,1)


Vehicle Care


10-35


Fuses TRANS TRLR


BCK/UP


Usage Transmission Trailer Back‐up Lamps


TRLR BRK Trailer Brake


TRLR


Trailer Parking Lamps


PRK LAMP TRLR PWR Trailer Power


WPR/WSW


Windshield Wiper/ Washer


Relays


A/C


CMPRSR CLTCH


Usage


Air Conditioning Compressor Clutch


AUX


VAC PUMP


CRNK


Auxiliary Vacuum Pump Switched Power


Relays FAN 1
FAN 2
FAN 3


Usage Cooling Fan 1
Cooling Fan 2
Cooling Fan 3


HID/


HI BEAM


LO BEAM


FOG LAMP Fog Lamps High‐Beam Headlamps High Intensity Discharge (HID) Low‐Beam Headlamps Horn Ignition Main Trailer Left Stoplamp and Turn Signal Lamp


LT TRLR STOP/TRN


HORN


IGN


PRK LAMP Parking Lamp PWR/TRN


Powertrain


Relays


Usage RR DEFOG Rear Window


RT TRLR STOP/TRN


Stop Lamps (China Only)


TRLR


BCK/UP


WPR


WPR HI


Defogger Trailer Right Stoplamp and Turn Signal Lamp Stop Lamps (China Only) Trailer Back-up Lamps Windshield Wiper Windshield Wiper High Speed


Instrument Panel Fuse Block The instrument panel fuse block is located under the instrument panel on the passenger side of the vehicle. Pull down on the cover to access the fuse block.


Buick Enclave Owner Manual - 2012


Black plate (36,1)


10-36


Vehicle Care


Fuses AIRBAG


AMP BCK/


UP/STOP


BCM


CNSTR/ VENT CTSY DR/LCK


DRL


DRL 2/ RR Fog


DSPLY


Fuse Side


The vehicle may not be equipped with all of the fuses, relays, and features shown.


FRT/WSW


HTD/


COOL SEAT


Usage


Fuses


Usage


Airbag Amplifier Back‐up Lamp/Stoplamp Body Control Module


Canister Vent


Courtesy Lamps Door Locks Daytime Running Lamps GMC HID Only (If Equipped)/ Rear Fog Lamps-China Only Display Front Windshield Washer Heated/ Cooling Seats


HVAC


Heating, Ventilation and Air Conditioning Inadvertent PWR/LED Power LED INFOTMNT Infotainment


INADV/


LT/TRN/SIG


MSM


PDM


Driver Side Turn Signal Memory Seat Module Power Mirrors, Liftgate Release


PWR MODE Power Mode


PWR/MIR


RDO


Power Mirrors Radio


REAR WPR Rear Wiper


RT/TRN/SIG


SPARE


STR/WHL/


ILLUM


Passenger Side Turn Signal Spare Steering Wheel Illumination


Buick Enclave Owner Manual - 2012


Black plate (37,1)


Vehicle Care


10-37


Usage


Relays


Usage


DRL2


LT/UNLCK


DRL


SPARE


FRT/WSW


Daytime Running Lamps 2 Relay (If Equipped) Driver Side Unlock Relay Daytime Running Lamps Relay (If Equipped) Spare Front Windshield Washer Relay


Driver Side Power Seat Relay Passenger Side Power Seat Relay Power Windows Relay Power Steering Column Relay Liftgate Relay Power Lock Relay Rear Window Washer Relay Power Unlock Relay


Relays LT/PWR/


SEAT


RT/PWR/


SEAT


PWR/WNDW


PWR/


COLUMN L/GATE


LCK


REAR/WSW


UNLCK


Relay Side


Buick Enclave Owner Manual - 2012


Black plate (38,1)


10-38


Vehicle Care


Wheels and Tires


Tires Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer.


{ WARNING . Poorly maintained and


improperly used tires are dangerous.


. Overloading the tires can


cause overheating as a result of too much flexing. There could be a blowout and a serious crash. See Vehicle Load Limits on page 9‑12.


(Continued)


WARNING (Continued)


WARNING (Continued)


. Underinflated tires pose the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when the tires are cold.


. Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when hitting a pothole. Keep tires at the recommended pressure. . Worn or old tires can cause a crash. If the tread is badly worn, replace them.


(Continued)


. Replace any tires that have been damaged by impacts with potholes, curbs, etc. . Improperly repaired tires


can cause a crash. Only the dealer or an authorized tire service center should repair, replace, dismount, and mount the tires.


. Do not spin the tires in


excess of 55 km/h (35 mph) on slippery surfaces such as snow, mud, ice, etc. Excessive spinning may cause the tires to explode.


Buick Enclave Owner Manual - 2012


Black plate (39,1)


Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples show a typical passenger vehicle tire and a compact spare tire sidewall.


Passenger (P‐Metric) Tire Example (A) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type,


and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. (C) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards.


Vehicle Care


10-39


(D) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 10‑56.


Buick Enclave Owner Manual - 2012


Black plate (40,1)


10-40


Vehicle Care


(G) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.


Compact Spare Tire Example


(A) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.


(B) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 5 000 km (3,000 mi) and should not be driven at speeds over 105 km/h (65 mph). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat. If the vehicle has a compact spare tire, see Compact Spare Tire on page 10‑78 and If a Tire Goes Flat on page 10‑60. (C) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows


the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (D) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. (E) Tire Inflation: The temporary use tire or compact spare tire should be inflated to 420 kPa (60 psi). For more information on tire pressure and inflation see Tire Pressure on page 10‑45.


Buick Enclave Owner Manual - 2012


Black plate (41,1)


(F) Tire Size: A combination of letters and numbers define a tire's width, height, aspect ratio, construction type, and service description. The letter T as the first character in the tire size means the tire is for temporary use only. (G) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.


Tire Designations


Tire Size The following is an example of a typical passenger vehicle tire size.


(A) Passenger (P‐Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width: The three‐digit number indicates the tire section width in millimeters from sidewall to sidewall.


Vehicle Care


10-41


(C) Aspect Ratio: A two‐digit number that indicates the tire height‐to‐width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted‐bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches.


Buick Enclave Owner Manual - 2012


Black plate (42,1)


10-42


Vehicle Care


(F) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.


Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight: The combined weight of optional accessories. Some examples of optional accessories are automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning.


Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in kPa (kilopascal) or psi (pounds per square inch) before a tire has built up heat from driving. See Tire Pressure on page 10‑45.


Curb Weight: The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR: Gross Vehicle Weight Rating. See Vehicle Load Limits on page 9‑12.


Buick Enclave Owner Manual - 2012


Black plate (43,1)


GAWR FRT: Gross Axle Weight Rating for the front axle. See Vehicle Load Limits on page 9‑12. GAWR RR: Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits on page 9‑12. Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT‐Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279
that corresponds to the load carrying capacity of a tire.


Maximum Inflation Pressure: The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lbs). See Vehicle Load Limits on page 9‑12. Occupant Distribution: Designated seating positions.


Vehicle Care


10-43


Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure on page 10‑45 and Vehicle Load Limits on page 9‑12.


Buick Enclave Owner Manual - 2012


Black plate (44,1)


10-44


Vehicle Care


Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road.


Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1.6 mm (1/16 in) of tread remains. See When It Is Time for New Tires on page 10‑53. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire's traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 10‑56.


Vehicle Capacity Weight: The number of designated seating positions multiplied by 68 kg (150 lbs) plus the rated cargo load. See Vehicle Load Limits on page 9‑12. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle capacity weight and the original equipment tire size and recommended inflation pressure. See “Tire and Loading Information Label” under Vehicle Load Limits on page 9‑12.


Buick Enclave Owner Manual - 2012


Black plate (45,1)


Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:


. Tire overloading and


overheating which could lead to a blowout.


. Premature or


irregular wear. . Poor handling. . Reduced fuel economy.


Overinflated tires, or tires that have too much air, can result in:


. Unusual wear. . Poor handling. . Rough ride. . Needless damage from


road hazards.


The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures. The recommended pressure is the minimum air pressure needed to support the vehicle's maximum load carrying capacity.


Vehicle Care


10-45


For additional information regarding how much weight the vehicle can carry, and an example of the Tire and Loading Information label, see Vehicle Load Limits on page 9‑12. How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.


When to Check Check the tires once a month or more. Do not forget the compact spare tire, if the vehicle has one. The compact spare should be at 420 kPa (60 psi). For additional information regarding the compact spare tire, see Compact Spare Tire on page 10‑78.


Buick Enclave Owner Manual - 2012


Black plate (46,1)


10-46


Vehicle Care


How to Check Use a good quality pocket-type gauge to check tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement.


If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air. Re‐check the tire pressure with the tire gauge. Return the valve caps on the valve stems to prevent leaks and keep out dirt and moisture.


Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)


Buick Enclave Owner Manual - 2012


Black plate (47,1)


Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start‐ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.


Vehicle Care


10-47


Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation on page 10‑48 for additional information. Federal Communications Commission (FCC) Rules and with Industry Canada Standards See Radio Frequency Statement on page 13‑23 for information regarding Part 15
of the Federal Communications Commission (FCC) Rules and with Industry Canada Standards RSS-GEN/210/220/310.


As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under‐inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under‐inflated tire causes the tire to overheat and can lead to tire failure. Under‐inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under‐inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.


Buick Enclave Owner Manual - 2012


Black plate (48,1)


10-48


Vehicle Care


Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly, if the vehicle has one. The TPMS sensors monitor the air pressure in the tires and transmits the tire pressure readings to a receiver located in the vehicle.


A message to check the pressure in a specific tire displays in the Driver Information Center (DIC). The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed. For additional information and details about the DIC operation and displays see Driver Information Center (DIC) on page 5‑27 and Tire Messages on page 5‑38.


When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the tire loading information label. See Vehicle Load Limits on page 9‑12.


Buick Enclave Owner Manual - 2012


Black plate (49,1)


Notice: Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use only the GM-approved tire sealant available through your dealer or included in the vehicle. Factory-installed Tire Inflator Kits use a GM approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See Tire Sealant and Compressor Kit on page 10‑62 for information regarding the inflator kit materials and instructions.


The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and needs to be inflated to the proper pressure. A Tire and Loading Information label shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load Limits on page 9‑12, for an example of the Tire and Loading Information label and its location. Also see Tire Pressure on page 10‑45. The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection on page 10‑52, Tire Rotation on page 10‑52 and Tires on page 10‑38.


Vehicle Care


10-49


TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message also displays. The malfunction light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause these to come on are: . One of the road tires has been


replaced with the spare tire. The spare tire does not have a TPMS sensor. The malfunction light and DIC message should go off after the road tire is replaced and the sensor matching process is performed successfully. See "TPMS Sensor Matching Process" later in this section.


Buick Enclave Owner Manual - 2012


Black plate (50,1)


10-50


Vehicle Care


The TPMS sensor matching process was not done or not completed successfully after rotating the tires. The malfunction light and the DIC message should go off after successfully completing the sensor matching process. See "TPMS Sensor Matching Process" later in this section . One or more TPMS sensors


are missing or damaged. The malfunction light and the DIC message should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer for service.


. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended could prevent the TPMS from functioning properly. See Buying

Loading...
x