Download PDF Manual


Index


238


2013 TSX 13 ACURA TSX 4D-31TL16400.book 239 ページ 2012年7月27日 金曜日 午前11時31分


uuMaintenance Under the HooduChanging the Engine Oil and Oil Filter


QRG


6-cylinder models


Drain Bolt


Washer


4-cylinder models


6-cylinder models


Oil Filter


Oil Filter


TOC


Index


7. Wipe away dirt and dust adhering to the contact surface of the engine block, and install a new oil filter.


8. Put a new washer on the drain bolt, then


reinstall the drain bolt. u Tightening torque: 29 lbf∙ft (39 N∙m,


4.0 kgf∙m)


9. Pour the recommended engine oil into


the engine. u Engine oil change capacity (including


1Changing the Engine Oil and Oil Filter


You will need a special wrench to replace the oil filter. You can buy this wrench from a dealer.


When installing the new oil filter follow the instructions supplied with the oil filter.


Reinstall the engine oil fill cap. Start the engine. The low oil pressure indicator should go off within five seconds. If it does not, turn off the engine, and check your work.


filter): 4-cylinder models 4.2 US qt (4.0 L) 6-cylinder models 4.5 US qt (4.3 L)


10. Reinstall the engine oil fill cap securely


and start the engine.


11. Run the engine for a few minutes, and


then check that there is no leak from the drain bolt or oil filter.


12. Stop the engine, wait for three


minutes, and then check the oil level on the dipstick. u If necessary, add more engine oil.


239


2013 TSX 13 ACURA TSX 4D-31TL16400.book 240 ページ 2012年7月27日 金曜日 午前11時31分


uuMaintenance Under the HooduEngine Coolant


QRG


Engine Coolant


Specified coolant: Honda Long Life Antifreeze/Coolant Type 2


1Engine Coolant


This coolant is premixed with 50% antifreeze and 50% water. Do not add any straight antifreeze or water.


We recommend you check the engine coolant level every time you refuel. Check the reserve tank first. If it is completely empty, also check the coolant level in the radiator. Add the engine coolant accordingly.


■ Reserve Tank


Reserve Tank


MAX MIN


Reserve Tank


6-cylinder models 1. Remove the right-side engine


compartment cover.


2 Engine Compartment Covers P. 233


All models 2. Check the amount of coolant in the


reserve tank.


3. If the coolant level is below the MIN mark,


add the specified coolant until it reaches the MAX mark.


4. Inspect the cooling system for leaks.


NOTICE 4-cylinder models If temperatures consistently below -22°F (-30°C) are expected, the coolant mixture should be changed to a higher concentration. Consult a dealer for more information.


If Honda antifreeze/coolant is not available, you may use another major brand non-silicate coolant as a temporary replacement. Check that it is a high quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.


Do not add rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or with the engine components.


TOC


Index


240


2013 TSX 13 ACURA TSX 4D-31TL16400.book 241 ページ 2012年7月27日 金曜日 午前11時31分


QRG


■ Radiator


Radiator Cap


TOC


Index


uuMaintenance Under the HooduEngine Coolant


1Radiator


3WARNING


Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.


Always let the engine and radiator cool down before removing the radiator cap.


NOTICE Pour the fluid slowly and carefully so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.


6-cylinder models 1. Remove the radiator cap cover. All models 2. Make sure the engine and radiator


are cool.


3. Turn the radiator cap counterclockwise and relieve any pressure in the coolant system. Do not push the cap down when turning.


4. Push down and turn the radiator cap


counterclockwise to remove it.


5. The coolant level should be up to the base


of the filler neck. Add coolant if it is low.


6. Put the radiator cap back on, and tighten


it fully.


7. Pour coolant into the reserve tank until it reaches the MAX mark. Put the cap back on the reserve tank.


241


2013 TSX 13 ACURA TSX 4D-31TL16400.book 242 ページ 2012年7月27日 金曜日 午前11時31分


uuMaintenance Under the HooduTransmission Fluid


QRG


Transmission Fluid ■ Automatic Transmission Fluid


Specified fluid: Acura ATF DW-1 (automatic transmission fluid)


Check the fluid level when the engine is at normal operating temperature. 4-cylinder models


1. Park on level ground, and start the engine.


Upper Lower Marks


6-cylinder models


Rubber Cap


Guide


HOT Range


Upper Mark Lower Mark


2. Wait until the radiator fan starts and then


turn off the engine. u Perform step 3 after waiting for about 60


seconds (less than 90 seconds).


3. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth.


4. Insert the dipstick all the way back into the transmission securely, as shown in the


image.


5. Remove the dipstick and check the


fluid level. u It should be between the upper and


lower marks in the HOT range.


6. If the level is below the lower mark,


add fluid into the dipstick hole to bring it to the level between the upper and lower marks, and have your vehicle checked by a dealer immediately.


TOC


Index


242


1Automatic Transmission Fluid


NOTICE Do not mix Acura ATF DW-1 with other transmission fluids. Using a transmission fluid other than Acura ATF DW-1 may adversely affect the operation and durability of your vehicle’s transmission, and damage the transmission.


Any damage caused by using a transmission fluid that is not equivalent to Acura ATF DW-1 is not covered by Acura’s new vehicle warranty.


NOTICE Pour the fluid slowly and carefully so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.


2013 TSX 13 ACURA TSX 4D-31TL16400.book 243 ページ 2012年7月27日 金曜日 午前11時31分


QRG


■ Manual Transmission Fluid


Specified fluid: Acura Manual Transmission Fluid (MTF)


Check the fluid level when the engine is at normal operating temperature. Under Cover


1. Park the vehicle on level ground.


2. Remove the bolts with a wrench, then


carefully remove the under cover.


uuMaintenance Under the HooduTransmission Fluid


1Manual Transmission Fluid


If Acura MTF is not available, you may use the API certificated SAE 0W-20 or 5W-20 viscosity motor oil as a temporary measure.


Replace with MTF as soon as possible. Motor oil does not contain the proper additives for the transmission and continued use can cause decreased shifting performance and lead to transmission damage.


Bolt


TOC


Index


3. Remove the transmission filler bolt and


washer. Carefully feel inside the bolt hole with your fingers. u Check if the fluid level is up to the edge


of the bolt hole.


4. If the fluid level is not up to the edge of the bolt hole, add Acura Manual Transmission Fluid (MTF) until it runs out of the hole.


5. Put a new washer on the filler bolt, then


reinstall the filler bolt. u Tightening torque:


33 lbf∙ft (44 N∙m, 4.5 kgf∙m)


6. Reinstall the under cover with the bolts.


243


2013 TSX 13 ACURA TSX 4D-31TL16400.book 244 ページ 2012年7月27日 金曜日 午前11時31分


uuMaintenance Under the HooduBrake/Clutch Fluid


QRG


Brake/Clutch Fluid


Specified fluid: Honda Heavy Duty Brake Fluid DOT 3


1Brake/Clutch Fluid


NOTICE Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.


If the specified brake fluid is not available, you should use only DOT 3 or DOT 4 fluid from a sealed container as a temporary replacement.


Using any non-Honda brake fluid can cause corrosion and decrease the longevity of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible.


If the brake fluid level is at or below the MIN mark, have a dealer inspect for leaks or worn brake pads as soon as possible.


Use the same fluid for both the brakes and clutch.


■ Checking the Brake Fluid


4-cylinder models


Brake Reservoir


The fluid level should be between the MIN and MAX marks on the side of the reservoir.


MAX


MIN


6-cylinder models


Brake Reservoir


MAX


MIN


TOC


Index


244


2013 TSX 13 ACURA TSX 4D-31TL16400.book 245 ページ 2012年7月27日 金曜日 午前11時31分


QRG


■ Checking the Clutch Fluid


Clutch Reservoir


The fluid level should be between the MIN and MAX marks on the side of the reservoir.


uuMaintenance Under the HooduBrake/Clutch Fluid


1Checking the Clutch Fluid


If the clutch fluid level is at or below the MIN mark, have a dealer inspect for leaks or an excessively worn clutch plate as soon as possible.


MAX


MIN


TOC


Index


245


2013 TSX 13 ACURA TSX 4D-31TL16400.book 246 ページ 2012年7月27日 金曜日 午前11時31分


uuMaintenance Under the HooduRefilling Window Washer Fluid


QRG


Refilling Window Washer Fluid Check the amount of window washer fluid using the washer fluid level gauge on the cap.


If the level is low, fill the washer reservoir.


1Refilling Window Washer Fluid


NOTICE Do not use engine antifreeze or a vinegar/water solution in the windshield washer reservoir. Antifreeze can damage your vehicle’s paint. A vinegar/water solution can damage the windshield washer pump.


Level Gauge


TOC


Index


246


2013 TSX 13 ACURA TSX 4D-31TL16400.book 247 ページ 2012年7月27日 金曜日 午前11時31分


Replacing Light Bulbs


QRG


Headlight Bulbs When replacing, use the following bulbs. High beam headlight: 60 W (HB3) Low beam headlight: 55 W (H1 for halogen bulb Type)


35 W (D2S for high voltage discharge type)


■ High Beam Headlight


4-cylinder models


6-cylinder models 1. Remove all the engine compartment covers.


2 Engine Compartment Covers* P. 233


Passenger side All models 2. Remove the engine coolant reservoir.


Engine Coolant Reservoir


6-cylinder models


Engine Coolant Reservoir


TOC


Index


1Headlight Bulbs


NOTICE Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.


The headlight aim is set by the factory, and does not need to be adjusted. However, if you regularly carry heavy items in the trunk or tow a trailer, have the aiming readjusted at a dealer or by a qualified technician.


The HB3 and H1 types are halogen bulbs. When replacing a bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.


* Not available on all models


Continued


247


2013 TSX 13 ACURA TSX 4D-31TL16400.book 248 ページ 2012年7月27日 金曜日 午前11時31分


uuReplacing Light BulbsuHeadlight Bulbs


QRG


4-cylinder models


Fastener


Cover


6-cylinder models


Air Intake Duct


Fastener


Driver side 4-cylinder models 3. Remove the fasteners, using a flat-tip


screwdriver. Remove the cover of the air intake duct and its upper part.


1Headlight Bulbs


The exterior lights’ inside lenses (headlights, brake lamps, etc.) may fog temporarily after a car wash or while driving in the rain. This does not impact the exterior light function. However, if you see a large amount of water or ice accumulated inside the lenses, have your vehicle inspected by a dealer.


6-cylinder models 3. Remove the fasteners, and remove the air


intake duct cover.


TOC


Cover


Index


248


2013 TSX 13 ACURA TSX 4D-31TL16400.book 249 ページ 2012年7月27日 金曜日 午前11時31分


uuReplacing Light BulbsuHeadlight Bulbs


QRG


4-cylinder models Coupler


Bulb


Driver and passenger side All models 4. Remove the coupler.


u It can be removed by pushing the tab.


5. Rotate the old bulb to the left to remove.


6. Insert a new bulb into the headlight


assembly and turn it to the right.


7. Insert the coupler into the connector of


Bulb


the bulb.


Tab


6-cylinder models Coupler


TOC


Tab


Index


Continued


249


2013 TSX 13 ACURA TSX 4D-31TL16400.book 250 ページ 2012年7月27日 金曜日 午前11時31分


uuReplacing Light BulbsuHeadlight Bulbs


High Voltage Discharge Types ■ Low Beam Headlights High voltage can remain in the circuit for a long period of time after the light is switched off. Do not attempt to inspect or replace the high voltage discharge type bulbs yourself. Ask a dealer to inspect and replace low beam headlights.


Halogen Types ■ Low Beam Headlights


Inner Fender


Screw


Clip


1. Turn the steering wheel all the way to


the opposite side from the headlight being replaced. Passenger side: Turn the steering wheel to the left. Driver side: Turn the steering wheel to the right.


2. Remove the holding clips and screws, and


pull the inner fender back.


3. Rotate the cover to the left, and remove.


Cover


QRG


TOC


Index


250


1Low Beam Headlights


Insert a flat-tip screwdriver, lift and remove the central pin to remove the clip.


2013 TSX 13 ACURA TSX 4D-31TL16400.book 251 ページ 2012年7月27日 金曜日 午前11時31分


uuReplacing Light BulbsuFog Light Bulbs


QRG


Bulb


Hook


Connector


4. Unhook the hook, and pull out


1Low Beam Headlights


the connector.


5. Remove the old bulb and insert the


new bulb.


6. Put the connector back into the


headlight assembly.


Insert the clip with the central pin raised, and push until it is flat.


Push until the pin is flat


Fog Light Bulbs When replacing, use the following bulbs. Fog Light: 55 W


1. Remove the clips using a flat-tip


screwdriver, and lower the under cover.


TOC


1Fog Light Bulbs


NOTICE Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.


The fog lights are halogen bulbs. When replacing a bulb, handle it by its plastic case, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.


Index


Clip


Under Cover


Continued


251


2013 TSX 13 ACURA TSX 4D-31TL16400.book 252 ページ 2012年7月27日 金曜日 午前11時31分


uuReplacing Light BulbsuFront Turn Signal/Parking/Side Marker Light Bulbs


Tab


Bulb


2. Remove the coupler.


u It can be removed by pushing the tab.


3. Rotate the old bulb to the left to remove.


4. Insert a new bulb into the fog light


assembly and turn it to the right.


Coupler


5. Insert the coupler into the connector of


the bulb.


Front Turn Signal/Parking/Side Marker Light Bulbs When replacing, use the following bulbs. Front Turn Signal/Parking/Side Marker: 21/5W


Turn the steering wheel and pull the inner fender back in the same way as when replacing the low beam headlights.


2 Changing the Low Beam Headlight P. 250


Socket


Bulb


1. Turn the socket to the left and remove it.


2. Push in the old bulb, rotate to the left until


it unlocks, and remove.


3. Insert a new bulb.


QRG


TOC


Index


252


2013 TSX 13 ACURA TSX 4D-31TL16400.book 253 ページ 2012年7月27日 金曜日 午前11時31分


uuReplacing Light Bulbs uSide Turn Signal/Emergency Indicator Light Bulbs


QRG


Side Turn Signal/Emergency Indicator Light Bulbs Door mirrors have the side turn lights. Have an authorized Acura dealer inspect and replace the light bulbs.


Brake Light, Taillight, Rear Turn Signal Light and Rear Side Marker Light Bulbs When replacing, use the following bulbs. Brake/Taillight: 21/5 W Rear Turn Signal Light: 21 W Rear Side Marker Light: 3 CP


Cover


1. Pull out and remove the cover.


TOC


Index


Continued


253


2013 TSX 13 ACURA TSX 4D-31TL16400.book 254 ページ 2012年7月27日 金曜日 午前11時31分


uuReplacing Light BulbsuBack-Up Light Bulbs


2. Turn the socket to the left and remove it.


Remove the old bulb.


3. Remove the old bulb and insert a new bulb.


Back-Up Light Bulbs When replacing, use the following bulbs. Back-Up Light: 21 W


Lining


1. Remove the clip in the trunk using a


flat-tip screwdriver.


2. Pull out the lining.


Clip


QRG


TOC


Index


254


2013 TSX 13 ACURA TSX 4D-31TL16400.book 255 ページ 2012年7月27日 金曜日 午前11時31分


uuReplacing Light BulbsuRear License Plate Light Bulbs


QRG


Lining


Clip


3. Turn the socket to the left and remove.


4. Remove the old bulb and insert the


new bulb.


Socket


Bulb


Rear License Plate Light Bulbs Have an authorized Acura dealer inspect and replace the light bulbs.


TOC


Index


255


2013 TSX 13 ACURA TSX 4D-31TL16400.book 256 ページ 2012年7月27日 金曜日 午前11時31分


uuReplacing Light BulbsuHigh-Mount Brake Light Bulbs


QRG


High-Mount Brake Light Bulbs When replacing, use the following bulbs. High-Mount Brake Light: 21 W


Bulb


1. Open the trunk.


2. Turn the socket to the left and remove it.


Socket


3. Remove the old bulb and insert a new bulb.


TOC


Index


256


2013 TSX 13 ACURA TSX 4D-31TL16400.book 257 ページ 2012年7月27日 金曜日 午前11時31分


Checking and Maintaining Wiper Blades


QRG


Checking Wiper Blades If the wiper blade rubber has deteriorated, it will leave streaks and the metal wiper arm may scratch the window glass.


Changing the Wiper Blade Rubber


1Changing the Wiper Blade Rubber


1. Lift the driver side wiper arm first, then the


passenger side.


NOTICE Avoid dropping the wiper arm; it may damage the windshield.


2. Place a cloth on the edge of the lock


tab. Push the lock tab up with a flat-tip screw driver.


3. Slide the blade from the wiper arm.


TOC


Index


Lock Tab


Continued


257


2013 TSX 13 ACURA TSX 4D-31TL16400.book 258 ページ 2012年7月27日 金曜日 午前11時31分


uuChecking and Maintaining Wiper BladesuChanging the Wiper Blade Rubber


4. Slide the wiper blade out from its holder by


pulling the tabbed end out.


Blade


Top


Retainer


Blade


5. Remove the retainers from the rubber blade


that has been removed, and mount to a new rubber blade. u Correctly align the rubber protrusion and


the retainer grooves.


Indent


Tab


6. Slide the new wiper blade onto the holder


from the bottom end. u The tab on the holder should fit in the


indent of the wiper blade.


7. Slide the wiper blade onto the wiper arm,


then push down the lock tab.


8. Lower the passenger side wiper arm first,


then the driver side.


QRG


TOC


Index


258


2013 TSX 13 ACURA TSX 4D-31TL16400.book 259 ページ 2012年7月27日 金曜日 午前11時31分


Checking and Maintaining Tires


QRG


Checking Tires To safely operate your vehicle, your tires must be of the proper type and size, in good condition with adequate tread, and properly inflated.


■ Inflation guidelines Properly inflated tires provide the best combination of handling, tread life, and comfort. Refer to the driver’s doorjamb label or specification’s page for the specified pressure.


Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from overheating.


Overinflated tires make your vehicle ride harshly, are more prone to road hazards, and wear unevenly.


Every day before you drive, look at each of the tires. If one looks lower than the others, check the pressure with a tire gauge.


At least once a month or before long trips, use a gauge to measure the pressure in all tires, including the spare. Even tires in good condition can lose 1 to 2 psi (10 to 20 kPa, 0.1 to 0.2 kgf/cm2) per month.


■ Inspection guidelines Every time you check inflation, also examine the tires and valve stems. Look for: • Bumps or bulges on the side or in the tread. Replace the tire if you find any cuts,


splits, or cracks in the side of the tire. Replace it if you see fabric or cord.


• Remove any foreign objects and inspect for air leaks.


• Uneven tread wear. Have a dealer check the wheel alignment.


TOC


Index


• Excessive tread wear.


2 Wear Indicators P. 264


• Cracks or other damage around valve stem.


1Checking Tires


3WARNING


Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.


Follow all instructions in this owner’s manual regarding tire inflation and maintenance.


Measure the air pressure when tires are cold. This means the vehicle has been parked for at least three hours, or driven less than 1 mile (1.6 km). If necessary, add or release air until the specified pressure is reached.


If checked when hot, tire pressure can be as much as 4–6 psi (30–40 kPa, 0.3–0.4 kgf/cm2) higher than if checked when cold.


Have a dealer check the tires if you feel a consistent vibration while driving. New tires and any that have been removed and reinstalled should be properly balanced.


259


2013 TSX 13 ACURA TSX 4D-31TL16400.book 260 ページ 2012年7月27日 金曜日 午前11時31分


uuChecking and Maintaining TiresuTire and Loading Information Label


QRG


Tire and Loading Information Label The label attached to the driver’s doorjamb provides necessary tire and loading information.


Label Example


Tire Labeling


Example


Tire Size Tire Identification Number (TIN)


Maximum Tire Load Maximum Tire Pressure


Tire Size


TOC


The tires that came on your vehicle have a number of markings. Those you should be aware of are described below.


Index


■ Tire Sizes Whenever tires are replaced, they should be replaced with tires of the same size.


260


1Tire and Loading Information Label


The tire and loading information label attached to the driver’s doorjamb contains: a The number of people your vehicle can carry. b The total weight your vehicle can carry. Do not


exceed this weight.


c The original tire sizes for front, rear and spare. d The proper cold tire pressure for front, rear and


spare.


1Tire Sizes


Following is an example of tire size with an explanation of what each component means. P225/50 R17 93V P: 225: Tire width in millimeters. 50:


Vehicle type (P indicates passenger vehicle).


Aspect ratio (the tire’s section height as a percentage of its width). Tire construction code (R indicates radial). Rim diameter in inches. Load index (a numerical code associated with the maximum load the tire can carry). Speed symbol (an alphabetical code indicating the maximum speed rating).


R: 17: 93:


V:


2013 TSX 13 ACURA TSX 4D-31TL16400.book 261 ページ 2012年7月27日 金曜日 午前11時31分


uuChecking and Maintaining TiresuTire Labeling


■ Tire Identification Number (TIN) The tire identification number (TIN) is a group of numbers and letters that look like the example in the side column. TIN is located on the sidewall of the tire.


■ Glossary of Tire Terminology Cold Tire Pressure – The tire air pressure when the vehicle has been parked for at least three hours or driven less than 1 mile (1.6 km).


1Tire Identification Number (TIN)


DOT B97R FW6X 2209
DOT: This indicates that the tire meets all


requirements of the U.S. Department of Transportation.


B97R: Manufacturer’s identification mark. FW6X: Tire type code. 22 09: Date of manufacture.


Load Rating – Means the maximum load that a tire is rated to carry for a given inflation pressure.


Year Week


Maximum Inflation Pressure – The maximum tire air pressure that the tire can hold.


Maximum Load Rating – Means the load rating for a tire at the maximum permissible inflation pressure for that tire.


Recommended Inflation Pressure – The cold tire inflation pressure recommended by the manufacturer.


Treadwear Indicators (TWI) – Means the projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread.


QRG


TOC


Index


261


2013 TSX 13 ACURA TSX 4D-31TL16400.book 262 ページ 2012年7月27日 金曜日 午前11時31分


uuChecking and Maintaining TiresuDOT Tire Quality Grading (U.S. Vehicles)


QRG


DOT Tire Quality Grading (U.S. Vehicles)


The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings.


■ Uniform Tire Quality Grading


Quality grades can be found where applicable on the tire sidewall between tread houlder and maximum section width.


■ Treadwear


The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.


1Uniform Tire Quality Grading


For example: Treadwear 200
Traction AA Temperature A


All passenger car tires must conform to Federal Safety Requirements in addition to these grades.


TOC


Index


262


2013 TSX 13 ACURA TSX 4D-31TL16400.book 263 ページ 2012年7月27日 金曜日 午前11時31分


uuChecking and Maintaining TiresuDOT Tire Quality Grading (U.S. Vehicles)


QRG


■ Traction


The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphat and concrete. A tire marked C may have poor traction performance.


■ Temperature


The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heate when te sted under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.


TOC


Index


1Traction


Warning: The traction grade assigned to this tire is abased on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.


1Temperature


Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


263


2013 TSX 13 ACURA TSX 4D-31TL16400.book 264 ページ 2012年7月27日 金曜日 午前11時31分


uuChecking and Maintaining TiresuWear Indicators


QRG


Wear Indicators


Example of a Wear Indicator mark


The groove where the wear indicator is located is 1/16 inch (1.6 mm) shallower than elsewhere on the tire. If the tread has worn so that the indicator is exposed, replace the tire. Worn out tires have poor traction on wet roads.


Tire Service Life The life of your tires is dependent on many factors, including driving habits, road conditions, vehicle loading, inflation pressure, maintenance history, speed, and environmental conditions (even when the tires are not in use).


In addition to regular inspections and inflation pressure maintenance, it is recommended that you have annual inspections performed once the tires reach five years old. All tires, including the spare, should be removed from service after 10 years from the date of manufacture, regardless of their condition or state of wear.


TOC


Index


264


2013 TSX 13 ACURA TSX 4D-31TL16400.book 265 ページ 2012年7月27日 金曜日 午前11時31分


uuChecking and Maintaining TiresuTire and Wheel Replacement


QRG


Tire and Wheel Replacement Replace your tires with radials of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall). Using tires of a different size or construction can cause the ABS and VSA® (vehicle stability assist) system to work incorrectly.


It is best to replace all four tires at the same time. If that isn’t possible, replace the front or rear tires in pairs.


1Tire and Wheel Replacement


3WARNING


Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.


Make sure that the wheel’s specifications match those of the original wheels. If you replace a wheel, only use TPMS specified wheels approved for your vehicle.


Always use the size and type of tires recommended in this owner’s manual.


TOC


Index


265


2013 TSX 13 ACURA TSX 4D-31TL16400.book 266 ページ 2012年7月27日 金曜日 午前11時31分


uuChecking and Maintaining TiresuTire Rotation


QRG


Tire Rotation Rotating tires according to the maintenance messages on the multi-information display helps to distribute wear more evenly and increase tire life.


■ Tires without rotation marks


Rotate the tires as shown here.


1Tire Rotation


Tires with directional tread patterns should only be rotated front to back (not from one side to the other). Directional tires should be mounted with the rotation indication mark facing forward, as shown below.


Front


Front


Direction Mark


■ Tires with rotation marks


Rotate the tires as shown here.


Front


TOC


Index


266


2013 TSX 13 ACURA TSX 4D-31TL16400.book 267 ページ 2012年7月27日 金曜日 午前11時31分


QRG


Winter Tires If driving on snowy or frozen roads, mount all season marked “M+S” tires, snow tires, or tire chains; reduce speed; and maintain sufficient distance between vehicles when driving.


Be particularly careful when operating the steering wheel or brakes to prevent skidding.


Use tire chains, snow tires, or all season tires when necessary or according to the law.


When mounting, refer to the following points.


For winter tires: • Select the size and load ranges that are the same as the original tires.


• Mount the tires to all four wheels.


For tire chains: • Install them on the front tires only.


• Because your vehicle has limited tire clearance, we strongly recommend using the


chains listed below: 4-cylinder models Cable-type: SCC Radial Chain SC1034


6-cylinder models Cable-type: SCC Radial Chain SC1038


• Follow the chain manufacturer’s instruction when installing. Mount them as


tightly as you can.


• Check that the chains do not touch the brake lines or suspension.


• Drive slowly.


TOC


Index


uuChecking and Maintaining Tires uWinter Tires


1Winter Tires


3WARNING


Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed.


Follow all instructions in this owner’s manual regarding the selection and use of tire chains.


NOTICE Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.


When tire chains are mounted, follow the chain manufacturer’s instructions regarding vehicle operational limits.


267


2013 TSX 13 ACURA TSX 4D-31TL16400.book 268 ページ 2012年7月27日 金曜日 午前11時31分


Battery


QRG


Checking the Battery


Test Indicator Window


Check the battery condition monthly. Look at the test indicator window and check the terminals for corrosion.


1Battery


3WARNING


If your vehicle’s battery is disconnected or goes dead: • The audio system is disabled.


2 Entering the audio security code P. 140


• The clock resets.


2 Adjusting the Time P. 88


• The navigation system is disabled. A PIN code will be required.


2 Refer to the navigation system manual


Charging the Battery Disconnect both battery cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative (–) cable first, and reconnect it last.


TOC


Index


268


The battery gives off explosive hydrogen gas during normal operation.


A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.


When conducting any battery maintenance, wear protective clothing and a face shield, or have a skilled technician do it.


WARNING: Battery post, terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.


The test indicator’s color information is on the battery.


When you find corrosion, clean the battery terminals by applying a baking powder and water solution. Rinse the terminals with water. Cloth/towel dry the battery. Coat the terminals with grease to help prevent future corrosion.


2013 TSX 13 ACURA TSX 4D-31TL16400.book 269 ページ 2012年7月27日 金曜日 午前11時31分


Remote Transmitter Care


QRG


Replacing the Battery If the indicator does not come on when the button is pushed, replace the battery.


1Replacing the Battery


Battery type: CR1616


1. Unscrew the cover with a small Phillips- head screwdriver. Push a button to pry open the transmitter.


NOTICE An improperly disposed of battery can damage the environment. Always confirm local regulations for battery disposal.


Replacement batteries are commercially available or at a dealer.


Keypad


Screw


2. Open the keypad.


u Wrap the small flat-tip screwdriver with a


cloth to prevent scratching the transmitter.


3. Make sure to replace the battery with the


correct polarity.


Battery


TOC


Index


269


2013 TSX 13 ACURA TSX 4D-31TL16400.book 270 ページ 2012年7月27日 金曜日 午前11時31分


Climate Control System Maintenance


QRG


Dust and Pollen Filter The climate control system is equipped with a dust and pollen filter that collects pollen, dust, and other debris in the air. The Maintenance MinderTM messages will let you know when to replace the filter.


We recommend that you replace the dust and pollen filter sooner when using your vehicle in areas with high concentrations of dust.


1Dust and Pollen Filter


Using an air freshener may reduce the deodorizing effect of the dust and pollen filter, and may reduce its life.


If the air flow from the climate control system deteriorates noticeably, and the windows fog up easily, the filter may need to be replaced. Please contact a dealer for replacement.


TOC


Index


270


2013 TSX 13 ACURA TSX 4D-31TL16400.book 271 ページ 2012年7月27日 金曜日 午前11時31分


Cleaning


QRG


Interior Care Use a damp cloth with a mixture of mild detergent and warm water to remove dirt. Use a clean cloth to remove detergent residue.


1Interior Care


Do not spill liquids inside the vehicle.


■ Cleaning Seat Belts Use a soft brush with a mixture of mild soap and warm water to clean the seat belts. Let the belts air dry. Wipe the openings of the seat belt anchors using a clean cloth.


Opening


Electrical devices and systems may malfunction if liquids are splashed on them.


Do not use silicone based sprays on electrical devices such as audio devices and switches.


Doing so may cause the items to malfunction or a fire inside the vehicle.


If a silicone based spray is inadvertently used on electrical devices, consult a dealer.


Depending on their composition, chemicals and liquid aromatics may cause discoloration, wrinkles, and cracking to resin-based parts and textiles. Do not use alkali solvents or organic solvents such as benzene or gasoline.


After using chemicals, make sure to gently wipe them off using a dry cloth.


Do not place used cloths on top of resin based parts or textiles for long periods of time without washing.


TOC


Index


Continued


271


2013 TSX 13 ACURA TSX 4D-31TL16400.book 272 ページ 2012年7月27日 金曜日 午前11時31分


uuCleaninguInterior Care


QRG


■ Floor Mats


To unlock


The front floor mats hook over the floor anchors, which keep the mats from sliding forward. To remove a mat for cleaning, turn the anchor knobs to the unlock position. When reinstalling the mat after cleaning, turn the knobs to the lock position.


1Floor Mats


If you use any floor mats that were not originally provided with your vehicle, make sure they are designed for your specific vehicle, fit correctly, and are securely anchored by the floor anchors.


Position the rear seat floor mats properly. If they are not properly positioned, the floor mats can interfere with the front seat functions.


Driver’s floor mat is shown.


Do not put additional floor mats on top of the anchored mats.


■ Maintaining Genuine Leather* Vacuum dirt and dust from the leather frequently. Pay close attention to the pleats and seams. Clean the leather with a soft cloth dampened with a 90% water and 10% neutral soap solution. Then buff it with a clean, dry cloth. Remove any dust or dirt on leather surfaces immediately.


TOC


Index


272


* Not available on all models


2013 TSX 13 ACURA TSX 4D-31TL16400.book 273 ページ 2012年7月27日 金曜日 午前11時31分


QRG


Exterior Care Dust off the vehicle body after you drive.


Regularly inspect your vehicle for scratches on painted surfaces. A scratch on a painted surface can result in body rust. If you find a scratch, promptly repair it.


■ Washing the Vehicle Wash the vehicle regularly. Wash more frequently when driving in the following conditions: • If driving on roads with road salt.


• If driving in coastal areas.


• If tar, soot, bird droppings, insects, or tree sap are stuck to painted surfaces.


■ Using an Automated Car Wash Fold in the door mirrors. Make sure to follow the instructions indicated on the automated car wash.


■ Using High Pressure Cleaners • Keep sufficient distance between the cleaning nozzle and the vehicle body.


• Take particular care around the windows. Standing too close may cause water to


enter the vehicle interior. Do not spray water into the engine compartment.


TOC


Index


uuCleaninguExterior Care


1Washing the Vehicle


Do not spray water into the air intake vents or engine compartment. It can cause a malfunction.


Air Intake Vents


Continued


273


2013 TSX 13 ACURA TSX 4D-31TL16400.book 274 ページ 2012年7月27日 金曜日 午前11時31分


uuCleaninguExterior Care


QRG


■ Applying Wax A good coat of automotive body wax helps protect your vehicle’s paint from the elements. Wax will wear off over time and expose your vehicle’s paint to the elements, so reapply as necessary.


1Applying Wax


NOTICE Chemical solvents and strong cleaners can damage the paint, metal, and plastic on your vehicle. Wipe up spills immediately.


■ Maintaining the Bumpers and Other Resin Coated Parts If you get gasoline, oil, engine coolant, or battery fluid on resin coated parts, they may be stained or the coating may peel. Promptly wipe it away using a soft cloth and clean water.


1Maintaining the Bumpers and Other Resin Coated Parts


Ask a dealer about the correct coating material when you want to repair the painted surface of the parts made of resin.


■ Cleaning the Window Wipe using a glass cleaner.


1Cleaning the Window


Wires are mounted to the inside of the rear window. Wipe along the same direction as the wires with a soft cloth so as not to damage them.


■ Maintaining Aluminum Wheels Aluminum is susceptible to deterioration caused by salt and other road contaminants. Use a sponge and mild detergent to wipe away promptly. Be careful not to use harsh chemicals (including some commercial wheel cleaners) or a stiff brush. They can damage the clear coat of the aluminum alloy wheels that helps keep the aluminum from corroding and tarnishing.


TOC


Index


274


2013 TSX 13 ACURA TSX 4D-31TL16400.book 275 ページ 2012年7月27日 金曜日 午前11時31分


QRG


Handling the Unexpected


This chapter explains how to handle unexpected troubles.


Tools .................................................. 276
Types of Tools.................................. 276
If a Tire Goes Flat.............................. 277
Changing a Flat Tire......................... 277


Engine Does Not Start


Checking the Engine........................ 283
Jump Starting.................................... 284
Shift Lever Does Not Move.............. 287
Overheating ...................................... 288
How to Handle Overheating............. 288


Index


Indicator, Coming On/Blinking


Fuses


. 290


If the Low Oil Pressure Indicator Comes On..................................... If the Charging System Indicator Comes On ..................................... If the Malfunction Indicator Lamp Comes On or Blinks ........................ 291
If the Brake System Indicator Comes On.. 292
If the EPS System Indicator Comes On... 292
If the Low Tire Pressure/TPMS Indicator Comes On or Blinks..........


290


293


Fuse Locations ................................. 294
Circuit Protected and Amps for 296
Each Fuse.................................... Inspecting and Changing Fuses........ 298
Emergency Towing........................... 299
When You Cannot Unlock the Fuel Fill Door................................................. 300
When You Cannot Open the Trunk.. 301


275


2013 TSX 13 ACURA TSX 4D-31TL16400.book 276 ページ 2012年7月27日 金曜日 午前11時31分


Tools


QRG


Types of Tools


1Types of Tools


The tools are stored in the trunk.


Jack Handle Bar


Wheel Nut Wrench/


Jack Handle


Tool Case


Jack


TOC


Index


276


2013 TSX 13 ACURA TSX 4D-31TL16400.book 277 ページ 2012年7月27日 金曜日 午前11時31分


If a Tire Goes Flat


QRG


Changing a Flat Tire If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually to reduce speed. Then, stop in a safe place. Replace the flat tire with a compact spare tire. Go to a dealer as soon as possible to have the full-size tire repaired or replaced.


1. Park the vehicle on firm, level, and non-slippery surface and apply the


parking brake.


Automatic transmission models 2. Move the shift lever in (P. Manual transmission models 2. Move the shift lever in (R.


All models 3. Set the parking brake.


4. Turn on the hazard warning lights and turn the ignition switch to LOCK (0.


TOC


Index


1Changing a Flat Tire


Periodically check the tire pressure of the compact spare. It should be set to the specified pressure. Specified Pressure: 60 psi (420 kPa, 4.2 kgf/cm2)


When driving with the compact spare tire, keep the vehicle speed under 50 mph (80 km/h). Replace with a full-size tire as soon as possible.


The compact spare tire and wheel in your vehicle are specifically for this model.


Do not use them with another vehicle.


Do not use another type of compact spare tire or wheel with your vehicle.


Do not mount tire chains on a compact spare tire. If a chain-mounted front tire goes flat, remove one of the full-size rear tires and replace it with the compact spare tire. Remove the flat front tire and replace it will the full-size tire that was removed from the rear. Mount the tire chains on the front tire.


Do not use a puncture-repairing agent on a flat tire, as it can damage the tire pressure sensor.


Continued

Loading...
x