Download PDF Manual

15 A 25
10 A 26
10 A 27


28
29
30
31
32


10 A 7.5 A 15 A − 7.5 A



: If equipped


Fuse Locations


Circuits Protected



VB SOL SRS Meter ACG Not Used Daytime Running Lights A/C Accessory, Key, Lock Accessory Driver’s Power Seat Sliding Moonroof Driver’s Power Seat Reclining Rear Left Power Window Front ACC Socket Driver’s Power Window Driver’s Side Door Lock Front Left Fog Light Left Side Small Lights (Exterior) Left Headlight High Beam TPMS Left Headlight Low Beam Not Used STS



CONTINUED 605


2013 TL 12/07/20 11:48:05 31TK4640_611


Fuse Locations


INTERIOR FUSE BOX Passenger’s side


No. Amps.


Circuits Protected


10 A 10 A


10 A 15 A − 7.5 A


Right Headlight High Beam Right Side Small Lights (Exterior) Right Front Fog Light Right Headlight Low Beam Not Used Interior Lights


606


No.


Amps.


Circuits Protected



Not Used Passenger’s Power Seat Reclining Passenger’s Power Seat Sliding Right Side Door Lock Rear Passenger’s Side Power Window Keyless Access System Front Passenger’s Power Window Not Used Premium amplifier Console ACC Socket Not Used Lumbar Support Seat Heaters Not Used Not Used Not Used


10
11


12
13


14
15
16
17
18
19
20
21
22


− 20 A


20 A


10 A 20 A


10 A 20 A


− 20 A 15 A − 7.5 A 20 A − − −



: If equipped


2013 TL 12/07/20 11:48:16 31TK4640_612


If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous.


OnSH-AWDmodels The only way you can safely tow your vehicle is with flat-bed equipment. The operator will load your vehicle on the back of a truck. Any other method of towing will damage the drive system. When you contact the towing agency, inform them a flat-bed is required.


Towing with only two tires on the ground will damage parts of the all-wheel-drive system. Your vehicle should be transported on a f lat-bed truck or trailer.


Emergency Towing


ExceptSH-AWDmodels There are two ways to tow your vehicle:


If, due to damage, your vehicle must be towed with the front wheels on the ground, do this:



Flat-bedEquipment loads your vehicle on the back of a truck. transport your vehicle.


This is the best way to


The operator



The tow


Wheel-liftEquipment truck uses two pivoting arms that go under the front tires and lift them off the ground. The rear tires remain on the ground. way to tow your vehicle.


This is an acceptable


Start the engine. Shift to the D position and hold for 5 seconds, then to N. Turn off the engine. Leave the ignition switch in the ACCESSORY (I) position so the steering wheel does not lock. Release the parking brake.



* Models equipped with the keyless access system have an engine start/ stop button instead of an ignition switch. ACCESSORY Mode is the equivalent of ACCESSORY (I). For more information, see pages 184


and


187


CONTINUED


607


2013 TL 12/07/20 11:48:22 31TK4640_613


Emergency Towing


Improper towing preparation will damage the transmission. Follow the above procedure exactly. If you cannot shif t the transmission or start the engine (automatic transmission), your vehicle must be transported with the f ront wheels of f the ground.


With the front wheels on the ground, it is best to tow the vehicle no farther than 50 miles (80 km), and keep the speed below 35 mph (55 km/h).


If your vehicle is equipped with a front spoiler, remove it before towing so it is not damaged.


Trying to lif t or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle’s weight.


608


The steering system can be damaged if the steering wheel is locked. Leave the ignition switch in the ACCESSORY (I) position, and make sure the steering wheel turns f reely bef ore you begin towing.



* Models equipped with the keyless


access system have an engine start/ stop button instead of an ignition switch. ACCESSORY Mode is the equivalent of ACCESSORY (I). For more information, see pages 184


and


187


On models with the Keyless Access system, the ENGINE START/STOP BUTTON indicator will conf irm that the power mode is in the ACCESSORY mode and that the steering lock is released. If the steering wheel does not turn f reely, rotate the wheel right and lef t while pressing the ENGINE START/STOP BUTTON. This inf ormation also appears on the multi- inf ormation display (see page


189


).


2013 TL 12/07/20 11:48:32 31TK4640_614


Emergency Towing, If Your Vehicle Gets Stuck


Onmodelswithkeylessaccesssystem If Your Vehicle Gets Stuck When you need to release the steering lock while your vehicle’s battery is dead, do this:


If your vehicle gets stuck in sand, mud, or snow, call a towing service to pull it out (see page


607


).


1.


2.


3.


Follow the proper jump starting procedures, Step 1 through Step 5, to apply the power to your vehicle (see pages


and


591


592


).


Press the ENGINE START/STOP button to set the power mode to ACCESSORY (see page ) and verify the steering lock is released.


184


Follow the jump starting procedures, Step 8 and Step 9, and the instructions to disconnect the jumper cable (see page ). The steering will remain unlocked even if the battery is dead.


592


Failure to comply means the steering lock may be damaged.


If you slip the clutch for a long time while trying to get unstuck, you may overheat and damage the transmission. Use a tow service to prevent transmission damage.


For very short distances, such as freeing the vehicle, you can use the detachable towing hook that mounts on the anchor in the front bumper.


To use the towing hook:


1.


2.


Remove the cover from the front bumper using your fingers, or pry it off using a cloth and a flat-tip screwdriver to prevent scratches.


Remove the towing hook and wheel nut wrench from the tool case in the spare tire (see page


584


).


CONTINUED


609


2013 TL To avoid damage to your vehicle, use the towing hook f or straight, f lat ground towing only. Do not tow at an angle. The tow hook should not be used to tow the vehicle onto a f lat bed. Do not use it as a tie down.


12/07/20 11:48:36 31TK4640_615


If Your Vehicle Gets Stuck


WHEEL NUT WRENCH


3.


Screw the towing hook into the hole, and tighten it with the wheel nut wrench.


610


2013 TL 12/07/20 11:48:39 31TK4640_616


Technical Information


The diagrams in this section give you the dimensions and capacities of your vehicle and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems.


Identification Numbers Specifications DOT Tire Quality Grading


................ ................................


(U.S. Vehicles)


.......................... Tire Labeling ................................. Tire Pressure Monitoring System


. 612
. 614


. 617
. 619


(TPMS)



Explanation


Required Federal ............................ .......................


. 621
. 623


Emissions Controls Three Way Catalytic


Converters


. 625
................................. Emissions Testing ........................ . 626
.. Devices that Emit Radio Waves . 628


611


2013 TL 12/07/20 11:48:43 31TK4640_617


Identification Numbers


Your vehicle has several identifying numbers located in various places.


The vehicle identification number (VIN) is the 17-digit number your dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side. It is also on the certification label attached to the driver’s doorjamb, and is stamped on the engine compartment bulkhead. The VIN is also provided in bar code on the certification label.


612


VEHICLE IDENTIFICATION NUMBER (VIN)


CERTIFICATION LABEL


2013 TL 12/07/20 11:48:47 31TK4640_618


The engine number is stamped into the engine block.


The transmission number is on a label on the side of the transmission.


MANUAL TRANSMISSION NUMBER


Identification Numbers


ENGINE NUMBER


AUTOMATIC TRANSMISSION NUMBER


613


2013 TL 12/07/20 11:49:04 31TK4640_619


Specifications


Dimensions Length Width Height Wheelbase Track


Front Rear


Weights Gross vehicle weight rating


Seating Capacities Total Front Rear


Air Conditioning Refrigerant type Charge quantity Lubricant type


194.0 in (4,928 mm) 74.0 in (1,880 mm) 57.2 in (1,452 mm) 109.3 in (2,775 mm) 63.2 in (1,605.5 mm) 63.8 in (1,620 mm)


See the certification label attached to the driver’s doorjamb.


HFC-134a (R-134a) −


17.8 19.6 oz (505 555 g)



ND-OIL8


614



2 :


Capacities Fuel tank


Engine coolant Engine oil


Automatic transmission fluid


Approx. 18.5 US gal (70 ) 1.66 US gal (6.3 ) 2.19 US gal (8.3 )


4.5 US qt (4.3 ) 4.2 US qt (4.0 ) 5.3 US qt (5.0 )


Change * Total Change *


Including filter Without filter


Total Change


2WD SH-AWD


3.3 US qt (3.1 ) 3.3 US qt (3.1 )


Total


2WD SH-AWD


Change Total


Change Total


Change Total


Manual transmission fluid Rear differential fluid (SH-AWD) Transfer assembly fluid (SH-AWD) Windshield washer reservoir 1 : *


U.S. Vehicle Canada Vehicle


7.5 US qt (7.1 ) 8.2 US qt (7.8 ) 2.2 US qt (2.1 ) 2.6 US qt (2.5 )


2.67 US qt (2.53 ) 2.93 US qt (2.77 )


0.45 US qt (0.43 ) 0.48 US qt (0.45 )


2.6 US qt (2.5 ) 6.1 US qt (5.8 )


Including the coolant in the reserve tank and that remaining in the engine Reserve tank capacity: 0.182 US gal (0.69 ) Excluding the oil remaining in the engine


2013 TL 12/07/20 11:49:24 31TK4640_620



Lights Headlight (Low beam ) Headlight (High beam/DRL) Front turn signal/parking lights Front side marker lights Front fog lights Rear turn signal lights Back-up lights Rear side marker lights Stop/taillights Side turn signal lights High-mount brake light License plate lights Trunk light Door courtesy lights Vanity mirror lights Console compartment light Glove box Light Foot light


35 W (D2S) 60 W (HB3) 28/8 W


(Amber)


(Amber)


3 CP 55 W (H11) 21 W 16 W 3 CP LED * LED * LED * 3 CP 5 W 3.4 W 1.4 W 1.4 W 1.4 W LED *




1 :


On vehicles with high voltage discharge type low beam headlights, replacement of a bulb should be performed by your dealer. 2 : Replacement of a light bulb should be done by your dealer.


Battery Capacity


12 V 12 V


− −


55 AH/5 HR 65 AH/20 HR


Engine (2WD) Type


Bore x Stroke Displacement Compression ratio Spark plugs


Engine (SH-AWD) Type


Bore x Stroke Displacement Compression ratio Spark plugs


Driver’s side


Passenger’s side


Fuses Interior


Under-hood


Specifications


Water cooled 4-stroke


SOHC VTEC 6-cylinder (V6),


gasoline engine


3.50 x 3.66 in (89.0 x 93.0 mm)


212 cu-in (3,471 cm )


11.2 : 1


NGK:


DILZKR7A11G


Water cooled 4-stroke


SOHC VTEC 6-cylinder (V6),


gasoline engine


3.54 x 3.78 in (90.0 x 96.0 mm)


223.5 cu-in (3,664 cm )


11.2 : 1


NGK: DENSO:


ILZKR7B-11S SXU22HCR11S


See pages 605 or the fuse label attached on the under panel. See pages 606 or the fuse label attached to the inside of the fuse box door. See page 604 or the fuse box cover.


CONTINUED 615


2013 TL 12/07/20 11:49:34 31TK4640_621


Specifications


Tires Size


Front/Rear


Pressure


Spare Front


Rear


Spare


* *


1,


* * *


3,


4,


P245/50R17 98V P245/45R18 96V P245/40R19 94V * T135/80D17 103M 32 psi (220 kPa , 2.2 kgf/cm )


2,


* * * * *


1,


3,


4,


34 psi (235 kPa , 2.4 kgf/cm )



32 psi (220 kPa , 2.2 kgf/cm ) * * * * *


1,


2,


3,


4,


34 psi (235 kPa , 2.4 kgf/cm ) * 60 psi (420 kPa , 4.2 kgf/cm )


* * * * * *


1 : 2 : 3 : 4 : 5 : 6 :


TL TL with Technology Package TL with Advance Package and Canadian Elite Package SH-AWD SH-AWD with Technology Package SH-AWD with Advance Package and Canadian SH-AWD Elite Package


0.00 in (0.0 mm) 0.08 in (2.0 mm)


0.5° − 1° − 3.8°


Alignment Toe-in


Camber


Caster


Front Rear Front Rear Front


616


2013 TL 12/07/20 11:49:41 31TK4640_622


The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings.


Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:


Treadwear 200
Traction AA Temperature A


All passenger car tires must conform to Federal Safety Requirements in addition to these grades.


DOT Tire Quality Grading (U.S. Vehicles)


Treadwear The treadwear grade is a compara- tive rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one- half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual condi- tions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.


Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.


Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.


617


2013 TL 12/07/20 11:49:45 31TK4640_623


DOT Tire Quality Grading (U.S. Vehicles)


Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


Temperature The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.


618


2013 TL 12/07/20 11:49:57 31TK4640_624


The tires that came on your vehicle have a number of markings. Those you should be aware of are described below.


TIRE LABELING EXAMPLE


(1)


(4)


(3)


(2)


(1)


Tire Size Tire Identification Number (TIN)


(1) (2) (3) Maximum Tire Pressure (4) Maximum Tire Load


TireSize Whenever tires are replaced, they should be replaced with tires of the same size. Following is an example of tire size with an explanation of what each component means.


P245/50R17 98V



Vehicle type (P indicates passenger vehicle).


245



Tire width in millimeters.


50



Aspect ratio (the tire’s section height as a percentage of its width).



Tire construction code (R indicates radial).


17



Rim diameter in inches.


Tire Labeling


98



Load index (a numerical code associated with the maximum load the tire can carry).



Speed symbol (an alphabetical code indicating the maximum speed rating).


CONTINUED


619


2013 TL 12/07/20 11:50:07 31TK4640_625


Tire Labeling


TireIdentificationNumber(TIN) The tire identification number (TIN) is a group of numbers and letters that look like the following example. TIN is located on the sidewall of the tire.


DOT B97R FW6X 2202


DOT



This indicates that the tire meets all requirements of the U.S. Department of Transportation.


B97R



Manufacturer’s identification mark.


FW6X



Tire type code.


2202



Date of manufacture. Year Week


620


Recommended Inflation Pressure The cold tire inflation pressure recommended by the manufacturer.



Treadwear Indicators (TWI) − Means the projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread.


Glossary of Tire Terminology Cold Tire Pressure pressure when the vehicle has been parked for at least three hours or driven less than 1 mile (1.6 km).


The tire air




Load Rating Means the maximum load that a tire is rated to carry for a given inflation pressure.


Maximum Inflation Pressure The maximum tire air pressure that the tire can hold.



Maximum Load Rating Means the load rating for a tire at the maximum permissible inflation pressure for that tire.



2013 TL 12/07/20 11:50:14 31TK4640_626


Tire Pressure Monitoring System (TPMS)



Required Federal Explanation


Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.


(If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)


As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated.


Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure.


Driving on a significantly under- inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.


Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.


CONTINUED


621


2013 TL 12/07/20 11:50:19 31TK4640_627


Tire Pressure Monitoring System (TPMS)



Required Federal Explanation


Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.


Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.


When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended.


TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.


622


2013 TL 12/07/20 11:50:26 31TK4640_628


The burning of gasoline in your vehicle’s engine produces several by- products. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx), and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Con- trolling the production of NOx, CO, and HC is important to the environ- ment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.’’ Carbon monoxide does not contri- bute to smog creation, but it is a poisonous gas.



The Clean Air Act The United States Clean Air Act sets standards for automobile emissions. It also requires that automobile manufacturers explain to owners how their emissions controls work and what to do to maintain them. This section summarizes how the emissions controls work.



In Canada, Acura vehicles comply with the Canadian emission requirements, as specified in an agreement with Environment Canada, at the time they are manufactured.


Crankcase Emissions Control System Your vehicle has a positive crankcase ventilation system. This keeps gasses that build up in the engine’s crankcase from going into the atmosphere. The positive crankcase ventilation valve routes them from the crankcase back to the intake manifold. They are then drawn into the engine and burned.


Emissions Controls


System


Evaporative Emissions Control As gasoline evaporates in the fuel tank, an evaporative emissions control canister filled with charcoal adsorbs the vapor. It is stored in this canister while the engine is off. After the engine is started and warmed up, the vapor is drawn into the engine and burned during driving.


Onboard Refueling Vapor Recovery The onboard refueling vapor recovery (ORVR) system captures the fuel vapors during refueling. The vapors are adsorbed in a canister filled with activated carbon. While driving, the fuel vapors are drawn into the engine and burned off.


623


2013 TL 12/07/20 11:50:35 31TK4640_629


Emissions Controls


Exhaust Emissions Controls The exhaust emissions controls include four systems: PGM-FI, ignition timing control, exhaust gas recirculation, and three way catalytic converter. These four systems work together to control the engine’s combustion and minimize the amount of HC, CO, and NOx that come out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.


PGM-FISystem The PGM-FI system uses sequential multiport fuel injection. It has three subsystems: air intake, engine control, and fuel control. The powertrain control module (PCM) in automatic transmission vehicles or the engine control module (ECM) in manual transmission vehicles uses various sensors to determine how much air is going into the engine. It


624


then controls how much fuel to inject under all operating conditions.


IgnitionTimingControlSystem This system constantly adjusts the ignition timing, reducing the amount of HC, CO, and NOx produced.


ExhaustGasRecirculation (EGR)System The exhaust gas recirculation (EGR) system takes some of the exhaust gas and routes it back into the intake manifold. Adding exhaust gas to the air/fuel mixture reduces the amount of NOx produced when the fuel is burned.


Replacement Parts The emissions control systems are designed and certified to work together in reducing emissions to levels that comply with the Clean Air Act. To make sure the emissions remain low, you should use only new Acura replacement parts or their equivalent for repairs. Using lower quality parts may increase the emissions from your vehicle.


The emissions control systems are covered by warranties separate from the rest of your vehicle. Read your warranty manual for more information.


ThreeWayCatalyticConverter The three way catalytic converter is in the exhaust system. Through chemical reactions, it converts HC, CO, and NOx in the engine’s exhaust to carbon dioxide (CO ), nitrogen (N ), and water vapor.


2013 TL 12/07/20 11:50:42 31TK4640_630


The three way catalytic converters contain precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converters are referred to as three-way catalysts, since they act on HC, CO, and NOx. Replacement units must be original Acura parts or their equivalent.


The three way catalytic converters must operate at a high temperature for the chemical reactions to take place. They can set on fire any combustible materials that come near them. Park your vehicle away from high grass, dry leaves, or other flammables.


Three Way Catalytic Converters


Keep the engine well maintained.


Have your vehicle diagnosed and repaired if it is misfiring, back- firing, stalling, or otherwise not running properly.


THREE WAY CATALYTIC CONVERTERS


Defective three way catalytic converters contribute to air pollution, and can impair your engine’s performance. Follow these guidelines to protect your vehicle’s three way catalytic converters.


Always use unleaded gasoline. Even a small amount of leaded gasoline can contaminate the catalyst metals, making the three way catalytic converters ineffective.


625


2013 TL 12/07/20 11:50:50 31TK4640_631


Emissions Testing


Testing of Readiness Codes If you take your vehicle for an emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain ‘‘readiness codes’’ that must be set in the on- board diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.


626


4.


5.


Without touching the accelerator pedal, start the engine, and let it idle for 20 seconds.


Keep the vehicle in Park (automatic) or neutral (manual). Increase the engine speed to 2,000
rpm, and hold it there until the temperature gauge rises to at least 1/4 of the scale (about 3 minutes).


6.


Without touching the accelerator pedal, let the engine idle for 20
seconds.


If the testing facility determines that the readiness codes are not set, you will be requested to return at a later date to complete the test. If you must get the vehicle retested within the next two or three days, you can condition the vehicle for retesting by doing the following.


1.


2.


3.


Make sure the gas tank is nearly, but not completely, full (around 3/4).


Make sure the vehicle has been parked with the engine off for 6
hours or more.


Make sure the ambient temperature is between 40° and 95°F (4° and 35°C).


2013 TL 12/07/20 11:50:54 31TK4640_632


Emissions Testing


7.


Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20
minutes. Drive on the highway in D (automatic) or 5th (manual). Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.) If you cannot do this for a continuous 90
seconds because of traffic conditions, drive for at least 30
seconds, then repeat it two more times (for a total of 90 seconds).


8.


Then drive in city/suburban traffic for at least 10 minutes. When traffic conditions allow, let the vehicle coast for several seconds without using the accelerator pedal or the brake pedal.


9.


Make sure the vehicle has been parked with the engine off for 30 minutes.


If the testing facility determines the readiness codes are still not set, see your dealer.


627


2013 TL 12/07/20 11:51:05 31TK4640_633


Devices that Emit Radio Waves


The following products and systems on your vehicle emit radio waves when in operation.


Audio


Audio System Bluetooth Bluetooth HandsFreeLink HomeLink Universal Transceiver AcuraLink Immobilizer System Remote Transmitter Keyless Access System Tire Pressure Monitoring System (TPMS) Blind Spot Information (BSI)


Each of the above complies with the appropriate requirements or the required standards of FCC (Federal Communications Commission) and Industry Canada Standard, described as follows:


628


AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.


Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.


ThisdevicecomplieswithIndustry CanadaStandardRSS-Gen/210/310. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterference,including interferencethatmaycauseundesired operationofthedevice.


2013 TL 12/07/20 11:51:08 31TK4640_634


Warranty and Client Relations


Client Service Information Warranty Coverages Reporting Safety Defects Authorized Manuals


.......... .................... ............. .....................


. 630
. 631
. 632
. 633


629


2013 TL 12/07/20 11:51:16 31TK4640_635


Client Service Information


Acura dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership’s management. The service manager or general manager can help. Almost all problems are solved in this way.


If you are dissatisfied with the decision made by the dealership’s management, contact Acura Client Relations


U.S. Owners: American Honda Motor Co., Inc. Acura Client Relations Mail Stop 500-2N-7E 1919 Torrance Blvd. Torrance, CA 90501-2746


Tel: (800) 382-2238


630


Canadian Owners: Honda Canada Inc. Acura Client Services 180 Honda Boulevard Markham, ON L6C 0H9


Tel: 1-888-9-ACURA-9
Fax: 1-877-939-0909
E-Mail: [email protected]


In Puerto Rico and the U.S. Virgin Islands:


Vortex Motor Corp. Bella International P.O. Box 190816
San Juan, PR 00919-0816


Tel: (787) 620-7546


When you call or write, please give us this information:


Vehicle Identification Number (see page


612


Name and address of the dealer who services your vehicle


Date of purchase


Odometer reading of your vehicle


Your name, address, and tele- phone number


A detailed description of the problem


Name of the dealer who sold the vehicle to you


2013 TL 12/07/20 11:51:24 31TK4640_636


U.S. Owners Your new Acura is covered by these warranties:


NewVehicleLimitedWarranty covers your new vehicle, except for the emissions control systems and accessories, against defects in materials and workmanship.



these two


EmissionsControlSystemsDefects WarrantyandEmissions PerformanceWarranty −

Loading...
x