2013 Acura TL Owners Manual

Solution

UNSUPPORTED Ver.

CONNECT RETRY

NO SONG

Appears when an unsupported iPod is inserted. Appears when the iPod cannot be authenticated. Appears when there are no files in the iPod.

363

2013 TL12/07/20 11:16:40 31TK4640_369

Playing a USB Flash Memory Device (Models with navigation system)

CATEGORY BAR

AUDIO BUTTON

364

INTERFACE DIAL

NAVIGATION SCREEN

VOL/ (VOLUME/POWER) KNOB

CENTER DISPLAY

HDD/ AUX BUTTON

SKIP BAR

SCAN/A.SEL (SCAN/AUTO SELECT) BAR

2013 TL12/07/20 11:16:50 31TK4640_370

Playing a USB Flash Memory Device (Models with navigation system)

To Play a USB Flash Memory Device This audio system can select and play the audio files on a USB flash memory device with the same controls used for the disc player. To play a USB flash memory device, connect it to the USB adapter cable in the console compartment, then press the HDD/AUX button until you see ‘‘USB’’ in the display. The power mode must be ACCESSORY or ON.

Your vehicle has the engine start/ stop button instead of an ignition switch. For more information on how to select the power mode, see page

184

＊

The audio system reads and plays the audio files on the USB flash memory device in MP3, WMA or AAC formats. The recommended USB flash memory devices are 256 MB or higher, and formatted with the FAT file system. Some digital audio players may be compatible as well.

Some USB flash memory devices (such as devices with security lock- out features, etc.) will not work in this audio unit. ＊

Only AAC format files recorded with iTunes are playable on this audio unit.

NOTE:

Do not use a device such as a card reader or hard drive as it or your files may be damaged.

Do not connect your USB flash memory device using a hub.

Do not use an extension cable to the USB adapter cable equipped with your vehicle.

Do not keep a USB flash memory device in the vehicle. Direct sunlight and high heat will damage it.

We recommend backing up your data before playing a USB flash memory device.

Depending on the type and number of files, it may take some time before they begin to play.

CONTINUED

365

2013 TL12/07/20 11:16:56 31TK4640_371

Playing a USB Flash Memory Device (Models with navigation system)

VoiceControlSystem You can select the AUX mode by using the voice control buttons, but cannot operate the play mode functions.

Some versions of MP3, WMA, or AAC format may not be supported. If an unsupported file is found, the audio unit displays UNSUPPORTED, then skips to the next file.

In WMA or AAC format, DRM (digital rights management) files cannot be played. If the system finds a DRM file, the audio unit displays UNPLAYABLE FILE, and then skips to the next file.

Combining a low sampling f requency with a low bitrate may result in extremely degraded sound quality.

Depending on the software the files were made with, it may not be possible to play some files, or display some text data.

Depending on the type of encoding and writing software used, there may be cases where character information does not display properly.

Some devices cannot be powered or charged via the USB adapter. If this is the case, use the accessory adapter to supply power to your device.

The order of files in USB playback may be different from the order of files displayed in PC or other devices etc. Files are played in the order stored in USB flash memory device.

366

2013 TL12/07/20 11:17:02 31TK4640_372

Playing a USB Flash Memory Device (Models with navigation system)

ConnectingaUSBFlash MemoryDevice

USB CONNECTOR

USB ADAPTER CABLE

2.

Connect the USB flash memory device to the USB adapter cable correctly and securely.

USB ADAPTER CABLE

1.

Unclip the USB connector by pulling it up, and pull out the USB adapter cable in the console compartment.

When the USB device is connected and the USB mode is selected on the audio system, the USB indicator is shown in the center display. It also shows the folder and file numbers. Pressing the AUDIO button displays the USB indicator, the folder and file names, and the elapsed time in the navigation screen.

CONTINUED

367

2013 TL12/07/20 11:17:09 31TK4640_373

Playing a USB Flash Memory Device (Models with navigation system)

−

To select a

Folder Selection different folder, press and release either side of the CATEGORY bar. side to skip to the next Press the folder, and press the side to skip to the beginning of the previous folder.

＋

−

ToSelectaFilefrom FolderandFileLists

You can also select a folder or file from the list by using the interface dial. Press the AUDIO button to show the audio display on the navigation screen. Use the interface dial to highlight the file, then press ENTER to set your selection.

ToChangeorSelectFiles Use the SKIP bar while a USB flash memory device is playing to select passages and change files.

−

side of the SKIP bar,

Each time you press and

SKIP release the the system skips forward to the beginning of the next file. Press and release the side of the bar, to skip backward to the beginning of the current file. Press it twice to skip to the beginning of the previous file.

To move rapidly within a file, press and hold either side ( of the SKIP bar.

or

368

2013 TL12/07/20 11:17:15 31TK4640_374

Playing a USB Flash Memory Device (Models with navigation system)

Push the selector up to display the ‘‘Select a folder’’ screen. Then turn the interface dial to select a folder, and press ENTER.

If you have more than one layer of folders (folders within folders), you can also see each folder on the screen.

To go back to the normal playing display, press the AUDIO button. Pressing the CANCEL button goes back to the previous screen and pressing the MAP button cancels the audio mode display.

ToSelectRepeat, RandomorScanMode: Push the interface selector down to display the AUDIO MENU.

You can select any type of repeat, random or scan mode on the audio menu screen.

Move the interface selector up to select BACK to show the USB screen, or press the CANCEL button to return to the previous screen.

CONTINUED

369

2013 TL12/07/20 11:17:26 31TK4640_375

Playing a USB Flash Memory Device (Models with navigation system)

TRACK REPEAT

REPEAT OFF ICON

TRACK REPEAT ICON

This function repeats playback of the track.

1.

On the USB main screen, push the interface selector down to display the AUDIO MENU.

2.

Turn the interface dial to select Repeat and press ENTER.

370

3.

Turn the interface knob, select the Track Repeat icon and press ENTER on the interface selector. Playback of the track that is currently being played will be repeated.

To cancel this function, turn the interface dial and select the Repeat OFF icon, and then press ENTER.

Pressing either side of the SKIP bar also cancels this function.

FOLDER REPEAT

FOLDER REPEAT ICON

This function replays all the tracks in a folder in the order that they were stored.

1.

On the USB main screen, push the interface selector down to display the AUDIO MENU.

2.

Turn the interface dial to select Repeat and press ENTER.

2013 TL12/07/20 11:17:35 31TK4640_376

Playing a USB Flash Memory Device (Models with navigation system)

TRACK RANDOM

RANDOM OFF ICON

3.

Turn the interface dial, select the Folder Repeat icon and press ENTER on the interface selector. Playback of the folder that is currently being played will be repeated.

To cancel this function, turn the interface dial and select the Repeat OFF icon, and then press ENTER on the interface selector.

3.

Turn the interface dial, select the Track Random icon and press ENTER on the interface selector. The tracks are played in random order.

To cancel this function, turn the interface dial and select the Random OFF icon, and then press ENTER on the interface selector.

TRACK RANDOM ICON

This function plays all the tracks on the USB flash memory device in random order.

1.

2.

On the USB main screen, push the interface selector down to display the AUDIO MENU.

Turn the interface dial, select Random and press ENTER on the interface selector.

CONTINUED

371

2013 TL12/07/20 11:17:46 31TK4640_377

Playing a USB Flash Memory Device (Models with navigation system)

FOLDER RANDOM

3.

Turn the interface dial, select the Folder Random icon and press ENTER on the interface selector. The files are played in random order.

To cancel this function, turn the interface dial and select the Random OFF icon, and then press ENTER on the interface selector.

TRACK SCAN

SCAN OFF ICON

FOLDER RANDOM ICON

This function plays all of the tracks in the current folder in random order.

1.

2.

On the USB main screen, push the interface selector down to display the AUDIO MENU.

Turn the interface dial, select Random and press ENTER on the interface selector.

372

TRACK SCAN ICON

This function samples all the tracks in the current folder in the order that they were recorded.

1.

2.

On the USB main screen, push the interface selector down to display the AUDIO MENU.

Turn the interface dial, select the Scan icon and press ENTER on the interface selector.

2013 TL12/07/20 11:17:56 31TK4640_378

Playing a USB Flash Memory Device (Models with navigation system)

3.

Turn the interface dial, select Track Scan icon and press ENTER on the interface selector. Each track or file is sampled for 10
seconds. When all the tracks in the folder have been scanned, regular playback is resumed.

To cancel this function, turn the interface dial and select the Scan OFF icon, and then press ENTER on the interface selector to play the last track sampled.

FOLDER SCAN

FOLDER SCAN ICON

This function samples the first file in each folder within the USB flash memory device.

1.

2.

On the USB main screen, push the interface selector down to display the AUDIO MENU.

Turn the interface dial, select the Scan icon and press ENTER on the interface selector.

3.

Turn the interface dial, select Folder Scan icon and press ENTER on the interface selector.

The first file of the first folder is sampled for 10 seconds. If no other operations are carried out, the first files of the remaining folders are played for 10 seconds. After the first file of the last folder is played back, regular playback is resumed.

To cancel this function, turn the interface dial and select the Scan OFF icon, and then press ENTER on the interface selector.

You can also select the scan feature with the SCAN side of the SCAN/ A.SEL bar on the control panel. Press and release the SCAN side of the bar. Press and hold the SCAN side of the bar to get out of the scan mode and play the last file sampled.

373

2013 TL12/07/20 11:18:04 31TK4640_379

Playing a USB Flash Memory Device (Models with navigation system)

USB Flash Memory Device Error Messages If you see an error message in the center display, see page

375

To Stop Playing a USB Flash Memory Device To play the radio, press the AM/FM, or button. Press the DISC button to switch to the disc mode. Press the HDD/AUX button to switch the audio mode between HDD Audio, USB and Bluetooth Audio.

You can also press the MODE button on the steering wheel to change modes.

If you reconnect the same USB flash memory device, the system will begin playing where it left off.

DisconnectingaUSBFlash MemoryDevice You can disconnect the USB flash memory device at any time even if the USB mode is selected on the audio system. Always follow the USB flash memory device’s instructions when you remove it.

When you disconnect the USB flash memory device while it is playing, the center display and the audio screen (if selected) show NO DATA.

374

2013 TL12/07/20 11:18:07 31TK4640_380

USB Flash Memory Device Error Messages (Models with navigation system)

If you see an error message in the center display while playing a USB flash memory device, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.

Error Message

Solution

FILE ERROR

UNSUPPORTED

UNPLAYABLE FILE

NO SONG

The system cannot read the file(s). Check the files in the USB flash memory device. There is a possibility that the files have been damaged. Appears when an unsupported USB flash memory device is inserted. Appears when the file is copyright protected, such as DRM. Appears when there are no playable files in the USB flash memory device.

375

2013 TL12/07/20 11:18:12 31TK4640_381

Bluetooth Audio System (Models with navigation system)

NAVIGATION SCREEN

CENTER DISPLAY

HDD/AUX BUTTON

SKIP BAR

TITLE BUTTON

AUDIO BUTTON

376

INTERFACE DIAL

2013 TL12/07/20 11:18:21 31TK4640_382

Bluetooth Audio System (Models with navigation system)

Your vehicle is equipped with a Audio system, which Bluetooth allows you to listen to streaming Audio audio from your compatible phone. This function is only available on phones that are paired and linked to the vehicle’s Bluetooth system (see page

HandsFreeLink (HFL)

Bluetooth

432

).

To Play

Bluetooth

Audio Files

＊

Press the HDD/AUX button with the power mode ACCESSORY or ON. When the phone is recognized, Audio you will see the message and icon on the center display and the audio control display on the navigation screen (if selected), and the system begins to play.

Bluetooth

Not all Bluetooth-enabled phones with streaming audio capabilities are compatible with the system. You can find an approved phone by visiting , or by www.acura.com/handsfreelink calling the HandsFreeLink consumer support at 1-888-528-7876. In Canada, visit www.handsfreelink.ca or call (888) 528-7876.

In some states, provinces, NOTE: and territories, it may be illegal to perform some data device functions while driving.

Make sure that your phone is paired and linked to HFL.

To begin to play the audio files, you may need to operate your phone. If so, follow the phone maker’s operating instructions.

Your vehicle has the engine start/ stop button instead of an ignition switch. For more information on how to select the power mode, see page

184

＊

If an iPod or USB flash memory device or audio unit connected to the auxiliary input jack was selected at the last mode, you will see iPod, USB or AUX in the center display and the audio control display on the navigation screen (if selected). Push the HDD/ AUX button again to play audio files from your Bluetooth

Audio phone.

CONTINUED

377

2013 TL12/07/20 11:18:29 31TK4640_383

Bluetooth Audio System (Models with navigation system)

Once a device is linked, the name of the device will appear on the screen. Pressing the TITLE button switches the center display between the Audio and the device Bluetooth name.

In the following conditions, the display shows ‘‘NO CONNECT’’ message after pressing the TITLE button.

The phone is not linked to HFL.

If more than one phone is paired to the HFL system, there will be a delay before the system begins to play.

A device name may not be NOTE: displayed on some phone devices.

The phone is not turned on.

The phone is not in the vehicle.

Another HFL compatible phone, which is not compatible for Audio, is already Bluetooth connected.

Bluetooth

Audio compatible

If your phone does not operate as described, make sure it is an Acura approved phone. To find out if your phone is approved, go to www.acura.com/handsfreelink (in Canada, or call the HandsFreeLink consumer support at 1-888-528-7876.

), www.handsfreelink.ca

378

VoiceControlSystem You can select the AUX mode by using the voice control buttons, but cannot operate the play mode functions.

Toskipafile Press the side of the SKIP bar to skip forward to the next file, and press the to the beginning of the current file. Push the side again to skip to the previous file.

side to skip backward

The skip function may not be

NOTE: available on some phone devices.

2013 TL12/07/20 11:18:36 31TK4640_384

Topauseorresumeafile

The resume/pause mode can stop playing a file temporarily.

Bluetooth Audio System (Models with navigation system)

Turn the interface dial to switch the setting between the resume/pause mode and the sound setup mode. Select Resume/Pause, then press ENTER to set your selection. Each time you press ENTER, the system switches between the resume mode and pause mode.

The pause function may not NOTE: be available on some phone devices.

Tochangesoundsettings

Press the AUDIO button to display the audio control display. Turn the dial to switch the setting between the resume/pause mode and the sound setup mode. Select Sound Setup, then press ENTER to set your selection.

CONTINUED

379

2013 TL12/07/20 11:18:43 31TK4640_385

Bluetooth Audio System (Models with navigation system)

Turn the dial to select a sound setup mode, then press ENTER to set your selection. See page sound setting information.

for more

296

Audio is playing, press the

ToswitchtoHFLmode If you receive a call when the Bluetooth PICK-UP button on the steering wheel. The screen and the center display switch to the HFL mode (see page

427

).

This device complies with the appropriate requirements or the required standards. See page 628
more information.

for

Toturnoffthe Bluetooth Audio mode Select any other audio mode by pressing a button; AM/FM, DISC, or HDD/AUX on the audio control panel, or press the MODE button on the steering wheel to select another audio mode.

Switching to another mode pauses the music playing from your phone.

After ending the call, press the HANG-UP button to go back to the Bluetooth

Audio mode.

380

2013 TL12/07/20 11:18:50 31TK4640_386

Protecting Your Discs

General Information Onmodelswithoutnavigationsystem

When using CD-R or CD-RW discs, use only high quality discs labeled for audio use.

Onmodelswithnavigationsystem

When using CD-R, CD-RW, DVD-R or DVD-RW discs, use only high quality discs labeled for audio use.

Allmodels

Play only standard, round, 5-inch (12 cm) discs. Smaller or odd- shaped discs may jam in the drive or cause other problems.

When recording a CD-R or CD-RW, the recording must be closed for it to be used by the disc changer.

When recording a CD-R, CD-RW, DVD-R or DVD-RW the recording must be closed for it to be used by the disc player.

Handle your discs properly to prevent damage and skipping.

When using DVD-R/RW discs, they should meet DVD verification standards.

Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.

381

2013 TL12/07/20 11:18:58 31TK4640_387

Protecting Your Discs

Protecting Discs When a disc is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep discs out of direct sunlight and extreme heat.

To clean a disc, use a clean soft cloth. Wipe across the disc from the center to the outside edge.

A new disc may be rough on the inner and outer edges. The small plastic pieces causing this roughness can flake off and fall on the recording surface of the disc, causing skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.

Never try to insert foreign objects in the disc changer.

382

Additional Information on Recommended Discs The in-dash disc player has a sophisticated and delicate mechanism. If you insert a damaged disc as indicated in this section, it may become stuck inside and damage the audio unit.

Examples of these discs are shown as follows.

Handle a disc by its edges; never touch either surface. Do not place stabilizer rings or labels on the disc. These, along with contamination from finger prints, liquids, and felt- tip pens, can cause the disc to not play properly, or possibly jam in the drive.

2013 TL12/07/20 11:19:10 31TK4640_388

1.

Bubbled, wrinkled, labeled, and excessively thick discs

4.

Small, irregular shaped discs

Protecting Your Discs

Bubbled/ Wrinkled

With Label/ Sticker

Using Printer Label Kit

Sealed

With Plastic Ring

3-inch (8-cm) CD

Triangle Shape

2.

Damaged discs

3.

Poor quality discs

Chipped/ Cracked

Warped

Burrs

Can Shape

Arrow Shape

CONTINUED

383

2013 TL12/07/20 11:19:20 31TK4640_389

Protecting Your Discs

5.

Discs with scratches, dirty discs

Recommended discs are printed with the following logo.

Fingerprints, scratches, etc.

Onmodelswithoutnavigationsystem CD-R or CD-RW may not play due to the recording conditions.

Onmodelswithnavigationsystem

CD-R, CD-RW, DVD-R or DVD-RW may not play due to the recording conditions.

Scratches and fingerprints on the discs may cause the sound to skip.

384

Audio unit may not play the following formats.

This audio unit cannot play a Dual- disc .

2013 TL12/07/20 11:19:29 31TK4640_390

Radio Frequencies Your vehicle’s radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kHz FM band: 87.7 to 107.9 MHz

Radio stations on the AM band are assigned frequencies at least 10 kHz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 MHz apart (87.9, 88.1, 88.3).

Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as ‘‘FM101.’’

Radio Reception How well your vehicle’s radio receives stations is dependent on many factors, such as the distance from the station’s transmitter, nearby large objects, and atmospheric conditions.

A radio station’s signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will go off and the sound will fade completely as you get out of range of the station’s signal.

AM/FM Radio Reception

Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio’s reception. You may temporarily hear both stations, or hear only the station you are close to.

CONTINUED

385

2013 TL12/07/20 11:19:35 31TK4640_391

AM/FM Radio Reception

This device complies with the appropriate requirements or the required standards. See page 628
more information.

for

Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.

Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one day and not receive it the next day because of a change in conditions.

Electrical interference from passing vehicles and stationary sources (such as garages or parking structures) can cause temporary reception problems.

386

2013 TL12/07/20 11:19:43 31TK4640_392

MODE BUTTON

VOL BUTTON

CH BUTTON

Three controls for the audio system are mounted in the steering wheel hub. These let you control basic functions without removing your hand from the wheel.

▲

) or down (

The VOL button adjusts the volume up ( ). Press the top or bottom of the button, hold it until the desired volume is reached, then release it.

▼

The MODE button changes the mode. Pressing the button repeatedly selects FM1, FM2, AM, XM1, XM2, disc (if a disc is loaded), HDD (on models with navigation system), AUX (if an appropriate audio unit is connected).

Audio (if paired),

Bluetooth

If an iPod or a USB flash memory device is plugged into the system, you can also select AUX.

＋

If you are listening to the radio, use the CH button to change stations. Each time you press the top ( ) of the button, the system goes to the next preset station on the band you are listening to. Press the bottom − preset station. If you press and hold the CH button ( ), the system goes into the skip (seek) mode. It stops when it finds a station with a strong signal.

) to go back to the previous

) or (

＋

−

Remote Audio Controls

If you are playing a disc, the system skips to the beginning of the next track/file (file in MP3, WMA, or AAC format) each time you press the top ( the bottom ( beginning of the current track/file. Press it twice to return to the previous track/file.

) of the CH button. Press

) to return to the

＋

−

In MP3, WMA or AAC mode, you can use the seek function to select folders. Press and hold the top ( ＋ of the CH button until you hear a beep to skip forward to the first file of the next folder. Press the bottom − previous folder.

) to skip backward to the

CONTINUED

387

2013 TLOnmodelswithoutnavigationsystem If you are playing a conventional CD (without the text data and not compressed in MP3 or WMA), you can use the skip function to select discs. Press and hold the top ( ) of ＋ the CH button until you hear a beep, to skip forward to the next disc. Press and hold the bottom ( ) to skip backward to the previous disc.

−

12/07/20 11:19:47 31TK4640_393

Remote Audio Controls

＋

) of the CH button to skip

If you are playing a USB flash memory device or iPod with the USB adapter cable, press and release the top ( forward to the beginning of the next file. Press the bottom ( ) to skip backward to the beginning of the current file. Press it twice to return to the previous file.

−

When playing a USB flash memory device, you can also use the seek function to skip the folder. To activate this, press and hold either side of the CH button until you hear a beep.

388

2013 TL12/07/20 11:19:52 31TK4640_394

Auxiliary Input Jack

When you plug in a mini-jack cable between a compatible audio unit and the jack, you will see AUX in the display and the system automatically switches to AUX mode.

When a compatible audio unit is connected to the jack, press the HDD/AUX button (AUX button on models without navigation system) to select it.

AUXILIARY INPUT JACK

The auxiliary input jack is inside the console compartment. The system will accept auxiliary input from standard audio accessories using a 1/8 inch (3.5 mm) stereo miniplug.

389

2013 TL12/07/20 11:20:00 31TK4640_395

Radio Theft Protection

If your vehicle’s battery is disconnected or goes dead, the audio system disables itself. If this happens, you will see ‘‘ENTER CODE’’ in the frequency display next time you turn on the system. Use the preset buttons to enter the five-digit code. The code is on the Anti-theft Identification Card included in your owner’s manual kit. When it is entered correctly, the radio will start playing.

The Anti-theft Identification Card also lists your audio serial number. It is best to store the card in a safe place at home. In addition, you should write the audio system’s serial number in this owner’s manual.

If you make a mistake entering the code, do not start over; complete the five-digit sequence, then enter the correct code. You have ten tries to enter the correct code. If you are unsuccessful in ten attempts, you

390

must then leave the system on for one hour before trying again.

The system will retain your AM and FM presets even if power is disconnected.

NOTE: If you have a My Acura account, it is easy to retrieve the anti-theft code online without having to access the serial number.

U.S.owners We recommend that you register the security code at My Acura (myacura. com). If you lose the Anti-theft Identification Card before registering the code at My Acura, you must obtain the code from your dealer or https://radionavicode.acura. com/ audio system’s serial number. If you do not have the serial number with you, ask your dealer or go to for radionavicode.acura.com/

. To do this, you will need the

https://

information on how to retrieve it.

Canadianowners If you lose the Anti-theft Identification Card, you must obtain the code from your dealer. To do this, you will need the audio system’s serial number. If you do not have the serial number with you, ask your dealer how to retrieve it.

Modelswithnavigationsystem You need to enter a separate code for the navigation system to reactivate. The Anti-theft Card also lists the navigation system’s security code and serial number. Follow the same procedure to retrieve the serial number and obtain the code, and read the navigation system manual for details.

2013 TL12/07/20 11:20:06 31TK4640_396

Onmodelswithoutnavigationsystem To set the time, press the CLOCK button until you hear a beep. The displayed time begins to blink.

Change the hours by pressing the H (hour) button until the numbers advance to the desired time. Change the minutes by pressing the M (minute) button until the numbers advance to the desired time.

Press the CLOCK button again to enter the set time.

Setting the Clock

On models without navigation system

CLOCK BUTTON

RESET BUTTON (PRESET 6)

MINUTE BUTTON (PRESET 5)

CONTINUED

391

HOUR BUTTON (PRESET 4)

2013 TL12/07/20 11:20:16 31TK4640_397

Setting the Clock

You can quickly set the time to the nearest hour. If the displayed time is before the half hour, press and hold the CLOCK button, then press the R (reset) button to set the time back to the previous hour. If the displayed time is after the half hour, the same procedure sets the time forward to the beginning of the next hour.

Onmodelswithoutnavigationsystem AdjustingtheClock withSETUPButton You can also adjust the clock and switch the clock display between 24-hours and 12-hours in the menu mode.

To adjust the clock setting:

For example:

1:06 would RESET to 1:00. 1:52 would RESET to 2:00.

1.

Press and release the SETUP button. The display shows you the menu items.

Onmodelswithnavigationsystem The navigation system receives signals from the global positioning system (GPS), and the displayed time is updated automatically by the GPS. Refer to the navigation system manual for how to adjust the time.

You can adjust the clock setting with the ignition switch in the ACCESSORY (I) or ON (II) position.

392

2.

Turn the selector knob to select ‘‘CLOCK ADJUST.’’

3.

Press the selector knob (ENTER) to enter your selection. The display changes to the clock adjusting display.

2013 TL12/07/20 11:20:26 31TK4640_398

Setting the Clock

MINUTE SETTING

4.

Turn the selector knob to select the item which you want to adjust. Turning the selector knob will change the selected item between the clock display setting, hours, minutes, and SET. The selected item is indicated with in the display.

△

5.

Turn the selector knob to change the setting between 12H and 24H.

6.

Press the selector knob (ENTER) to enter your selection. The display will return to the clock adjusting display.

7.

To set the time, turn the selector knob and select the hours or the minutes, then press the knob to enter your selection. The display changes to the setting display.

8.

Turn the selector knob to count the numbers up or down.

CONTINUED

393

2013 TL12/07/20 11:20:31 31TK4640_399

Setting the Clock

9.

Press the selector knob (ENTER) to enter your selection. The display will return to the clock adjusting display.

While setting the clock, pressing the RETURN button will go back to the previous display. Pressing the SETUP button again will cancel this setting mode.

394

10.

To enter the clock setting, turn the selector knob to select ‘‘SET,’’ then press the knob. The display will return to the menu item display.

11.

Press either the RETURN or SETUP button to go back to the normal display.

2013 TL12/07/20 11:20:37 31TK4640_400

The security system helps to protect your vehicle and valuables from theft. The horn sounds and a combination of headlights, parking lights, side marker lights and taillights flashes if someone attempts to break into your vehicle or remove the audio unit. This alarm continues for two minutes, then the system resets. To deactivate the system before the two minutes have elapsed, unlock the driver’s door with the key or use the remote transmitter/keyless access remote.

Onmodelswithkeylessaccesssystem You can also deactivate the system by grabbing either front door handle while carrying the keyless access remote to unlock the door.

The security system automatically sets 15 seconds after you lock the doors, hood, and trunk. For the system to activate, you must lock the doors from the outside with the key,

SECURITY SYSTEM INDICATOR

A/T model is shown.

or use driver’s lock tab, master door lock switch, or remote transmitter (keyless access remote on models with keyless access system). The security system indicator on the instrument panel starts blinking immediately to show you the system is setting itself.

Security System

Once the security system sets, opening any door, the trunk, or hood without using the key or the remote transmitter/keyless access remote, will cause the alarm to activate. It also activates if the ignition switch is turned to the ON (II) position, the audio unit is removed from the dashboard, or the wiring is cut.

＊

Onmodelswithkeylessaccesssystem You can also set the security system by pressing the lock button on either front door handle while carrying the keyless access remote.

＊ Models equipped with the keyless access system have an engine start/ stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and

184

187

CONTINUED

395

2013 TL12/07/20 11:20:42 31TK4640_401

Security System

With the system set, you can still open the trunk with the remote transmitter/keyless access remote without triggering the alarm. The alarm will sound if the trunk is opened with the trunk release button on the driver’s door, the trunk release handle behind the trunk pass-through cover, or the emergency trunk opener.

The security system does not set if any door, the trunk, or hood is not fully closed. Before you leave the vehicle, make sure the doors, trunk and hood are securely closed.

To see if the system sets after you exit the vehicle, press the LOCK button on the remote transmitter/ keyless access remote within five seconds. If the system is set, the horn will beep once.

Do not attempt to alter this system or add other devices to it.

396

2013 TL12/07/20 11:20:52 31TK4640_402

Onmodelswithoutnavigationsystem Compass Operation Compass operation can be affected by driving near power lines or stations, across bridges, through tunnels, over railroad crossings, past large vehicles, or driving near large objects that can cause a magnetic disturbance. It can also be affected by accessories such as antennas and roof racks that are mounted by magnets.

When you turn the ignition switch to the ON (II) position, the compass is self-calibrating, then the compass display is shown in the display.

Compass Calibration

Compass

COMPASS

U.S. model is shown.

The compass may need to be manually calibrated after exposure to a strong magnetic field. If the compass seems to be continually showing the wrong direction and is not self-calibrating, or the compass display is blinking with the CAL indicator on, do the following procedure.

COMPASS SETTING MENU ITEMS

Do this procedure in an open

NOTE: area, away from buildings, power lines, and other vehicles.

1.

Turn the ignition switch to the ON (II) position.

2.

Press and hold the SETUP button for about 5 seconds. The display shows you the compass setting menu items.

CONTINUED

397

2013 TL12/07/20 11:21:00 31TK4640_403

Compass

3.

Turn the selector knob to select ‘‘CALIBRATION.’’

398

5.

Press the selector knob (ENTER). The compass display is blinking and the CAL indicator is shown.

6.

Drive the vehicle slowly in two complete circles.

When the calibration is successfully completed, the CAL indicator goes off and the compass display will stop blinking and show an actual heading.

The audio system is not related to the compass system. Even if the compass system is calibrating, the display returns to the normal display which you last selected.

4.

Press the selector knob (ENTER) to enter your selection. The display shows you ‘‘PUSH CAL START.’’

While setting the compass, press the RETURN button to go back to the previous display. Pressing the SETUP button will cancel the compass setting mode.

2013 TL12/07/20 11:21:09 31TK4640_404

Compass Zone Selection In most areas, there is a variation between magnetic north and true north. Zone selection is required so the compass can compensate for this variation. To check and select the zone, do this:

1.

Turn the ignition switch to the ON (II) position.

2.

3.

Press and hold the SETUP button for about 5 seconds. The display shows you the compass setting menu items.

Turn the selector knob to select ‘‘ZONE.’’ Press the selector knob (ENTER) to enter your selection. The display shows you the currently selected zone number.

Compass

ZONE NUMBER

5.

Once the correct zone is displayed, press the selector knob. The display then returns to normal.

CONTINUED

399

4.

Find the zone for your area on the map (see page ). If the correct zone is not shown, turn the selector knob to cycle the zone lists up or down.

400

If necessary, press the RETURN button to return to the previous display. Pressing the SETUP button will cancel the compass setting mode.

2013 TL12/07/20 11:21:13 31TK4640_405

Compass

The audio system is not related to the compass system. Even if the compass system is in the zone setting mode, the display returns to the normal display which you last selected.

Zone Map

400

2013 TL12/07/20 11:21:21 31TK4640_406

Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather.

Improper use of the cruise control can lead to a crash.

Use the cruise control only when traveling on open highways in good weather.

Using the Cruise Control

CRUISE BUTTON

RES/ACCEL BUTTON

CANCEL BUTTON

SET/DECEL BUTTON

1.

Push in the CRUISE button on the steering wheel. The CRUISE MAIN indicator on the instrument panel will come on.

The cruise control system can be left on, even when it is not in use.

2.

Accelerate to the desired cruising speed above 25 mph (40 km/h).

Cruise Control

3.

Press and release the SET/ DECEL button on the steering wheel. The CRUISE CONTROL indicator on the instrument panel comes on to show the system is now activated.

Cruise control may not hold the set speed when you are going up and down hills. If your vehicle speed increases going down a hill, use the brakes to slow down. This will cancel the cruise control. To resume the set speed, press the RES/ACCEL button. The CRUISE CONTROL indicator on the instrument panel will come back on.

CONTINUED

401

2013 TL12/07/20 11:21:29 31TK4640_407

Cruise Control

Changing the Set Speed You can increase the set cruising speed in any of these ways:

Press and hold the RES/ACCEL button. When you reach the desired cruising speed, release the button.

Push on the accelerator pedal. Accelerate to the desired cruising speed, then press the SET/ DECEL button.

To increase the speed in very small amounts, tap the RES/ ACCEL button. Each time you do this, your vehicle speeds up about 1 mph (1.6 km/h).

402

You can decrease the set cruising speed in any of these ways:

If you need to decrease your NOTE: speed quickly, use the brakes as you normally would.

Even with cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed.

Press and hold the SET/DECEL button. Release the button when you reach the desired speed.

Resting your foot on the brake or clutch pedal causes the cruise control to cancel.

To slow down in very small amounts, tap the SET/DECEL button. Each time you do this, your vehicle will slow down about 1 mph (1.6 km/h).

Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL indicator on the instrument panel will go out. When the vehicle slows to the desired speed, press the SET/ DECEL button.

2013 TL12/07/20 11:21:35 31TK4640_408

Canceling Cruise Control

CRUISE BUTTON

CANCEL BUTTON

You can cancel cruise control in any of these ways:

Tap the brake or clutch pedal.

Push the CANCEL button on the steering wheel.

Push the CRUISE button on the steering wheel.

Resuming the Set Speed When you push the CANCEL button, or tap the brake or clutch pedal, the system will remember the previously set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h), and then press and release the RES/ACCEL button. The CRUISE CONTROL indicator comes on. The vehicle will accelerate to the same cruising speed as before.

Cruise Control