(manual transmission) while carrying the keyless access remote, the power mode switches between VEHICLE OFF (LOCK), ACCESSORY, and ON.
Automatictransmission: You can start the engine at any time by pressing the engine start/stop button, while pressing the brake pedal, with the shift lever in Park or neutral position.
Manualtransmission: You can start the engine at any time by pressing the engine start/stop
2013 TL12/07/20 10:53:24 31TK4640_190
Automatic Transmission
Manual Transmission
Keyless Access System
VEHICLE OFF (LOCK) Indicator in the button is off.
ACCESSORY Indicator in the button is on. Indicator in the button blinks (from ON to ACCESSORY) Some electrical components such as the audio system and accessory power sockets can be operated.
ON Indicator in the button is on when the engine is not running. (If the engine is running, this indicator is off.) All electrical components can be used.
Do the following without pressing the brake pedal.
: Press the engine start/stop button. : Press the engine start/stop button without the shift lever in P. : Shift to Park, then press the engine start/stop button.
: Press the engine start/stop button without pressing the clutch pedal.
CONTINUED
185
2013 TLManualTransmission Each time you press the engine start/stop button without pressing the clutch pedal, the power mode switches between VEHICLE OFF (LOCK), ACCESSORY, and ON modes. To change the mode from ON to ACCESSORY, or ACCESSORY to VEHICLE OFF (LOCK), press the engine start/stop button twice.
12/07/20 10:53:31 31TK4640_191
Keyless Access System
AutomaticTransmission How the mode is switched depends on if the shift lever is in Park or not.
With the shift lever in Park, the power mode changes from ON to VEHICLE OFF (LOCK) when you push the engine start/stop button.
To change the mode from ON to ACCESSORY with the shift lever position in Park, take your foot off the brake and press the engine start/stop button twice.
To change the mode from ACCESSORY to VEHICLE OFF (LOCK), shift to Park, then press the engine start/stop button twice.
186
If the keyless access system NOTE: main switch in the glove box is off, make sure to insert the keyless access remote into the keyless access slot to turn on your vehicle’s power mode. For more information, refer to page
195
To remove the keyless access remote from the slot, make sure the power mode is VEHICLE OFF (LOCK).
2013 TL12/07/20 10:53:42 31TK4640_192
Keyless Access System
Ignition Switch and Power Mode Comparison
Ignition Switch Position
Without Keyless Access System
Power Mode
With Keyless Access System and Engine Start/Stop Button
LOCK (0)
ACCESSORY (I)
ON (II)
START (III)
Engine is turned off and power is shut down. The steering wheel is locked. No electrical components can be used.
VEHICLE OFF (LOCK)
Indicator-Off
Engine is turned off and power is shut down. The steering wheel is locked. No electrical components can be used.
Engine is turned off. Some electrical components such as the audio system and accessory power sockets can be operated.
Normal key position while driving. All electrical components can be used.
Use this position to start the engine. The ignition switch returns to the ON (II) position when you release the key.
ACCESSORY
ON
START
Indicator is:
On
Off
Indicator- On (engine is turned off) Off (engine is running)
All electrical components can be used.
Indicator-Off The mode automatically returns to ON after the engine starts.
Indicator-On or blinking Engine is turned off. Some electrical components such as the audio system and accessory power sockets can be operated.
187
2013 TL12/07/20 10:53:55 31TK4640_193
Keyless Access System
Starting the Engine
ENGINE START/STOP BUTTON
BRAKE PEDAL
AUTOMATIC TRANSMISSION
You can start the engine in any power mode.
To start the engine:
AutomaticTransmission 1.
Move the shift lever to Park (P).
2.
Depress the brake pedal and press the engine start/stop button.
188
ENGINE START/STOP BUTTON
StartingGuidance
TO START ENGINE: A/T
TO TURN ACCESSORY ON:
CLUTCH PEDAL
MANUAL TRANSMISSION
ManualTransmission 1.
Apply the parking brake.
2.
Press the clutch pedal down all the way. The engine does not start unless the clutch pedal is pressed.
3.
Press the engine start/stop button.
M/T
After you unlock and open the driver’s door, you will see the ‘‘TO START ENGINE:’’ message on the multi-information display. The ‘‘ TO TURN ACCESSORY ON:’’ message will be shown after three seconds. The display switches between the ‘‘TO START ENGINE:’’ and ‘‘TO TURN ACCESSORY ON:’’ messages every three seconds.
2013 TL12/07/20 10:54:02 31TK4640_194
Whenthekeylessaccesssystemmain the multi- switchinthegloveboxisoff, information display shows the ‘‘INSERT KEYLESS REMOTE INTO SLOT’’ message, then the ‘‘TO START ENGINE:’’ message will be shown after you insert the remote into the slot. Each time you press the engine start/stop button, the ‘‘INSERT KEYLESS REMOTE INTO SLOT’’ message is shown on the multi-information display if the remote is not in the slot.
NOTE: If the keyless access remote battery dies, you may have to use the built-in key to unlock/lock the vehicle. The built-in key is stored inside the keyless access remote (see page
201
).
After entering the vehicle, insert the keyless access remote into the slot to start the engine (see page ).
197
Keyless Access System
Tounlockthesteeringwheel
TO UNLOCK WHEEL
If the steering wheel is locked, the engine cannot start. The multi- information display shows you the above message and the indicator in the engine start/stop button blinks. To unlock the steering wheel, apply force by turning it left and right while pressing the engine start/stop button at the same time.
189
2013 TL12/07/20 10:54:13 31TK4640_195
Keyless Access System
Stopping the Engine
If the shift lever is in any gear other than neutral, depress the clutch pedal, then press the engine start/stop button.
OperationGuidance
SHIFT TO PARK
The engine stops and the power mode switches from ON to VEHICLE OFF (LOCK).
Before leaving the vehicle, make sure it is off. You can verify if the power is off by checking the engine start/stop button LED indicator.
Onmanualtransmissionmodels Make sure to press the brake pedal or set the parking brake before turning off the engine. If your foot is OFF the clutch pedal in any gear position, pressing the engine start/ stop button turns off the engine, and the vehicle may move forward or backward.
A/T model
To turn the vehicle off, make sure the vehicle is completely stopped and do the following.
AutomaticTransmission 1. 2.
Shift to park (P). Press the engine start/stop button with your foot on the brake pedal.
ManualTransmission
If the shift lever is in neutral, press the engine start/stop button.
190
A/T model only
Onautomatictransmissionmodels You can only place the vehicle in the VEHICLE OFF (LOCK) mode if the transmission is in Park. You will see the ‘‘SHIFT TO PARK’’ message on the multi-information display if you press the engine start/stop button to turn the vehicle off with the shift lever in any other position except for P (Park).
2013 TL12/07/20 10:54:21 31TK4640_196
ACCESSORY MODE
TO TURN VEHICLE OFF
Allmodels If the power mode is in ACCESSORY, you may see the ‘‘ACCESSORY MODE’’ message on the multi- information display.
After the driver’s door is opened, you will see the ‘‘TO TURN VEHICLE OFF:’’ message on the multi- information display. Press the engine start/stop button twice with your foot off the brake pedal to change the power mode from ACCESSORY to VEHICLE OFF (LOCK).
Keyless Access System
If you open the driver’s door in the ACCESSORY mode, a beeper will sound. You will also see a ‘‘ACCESSORY MODE’’ or ‘‘TO TURN VEHICLE OFF:’’ message on the multi-information display.
Press the engine start/stop button twice with your foot off the brake pedal (automatic transmission) or the clutch pedal (manual transmission) to change the power mode to VEHICLE OFF (LOCK).
Before leaving the vehicle, make sure it is in VEHICLE OFF (LOCK).
CONTINUED
191
2013 TL12/07/20 10:54:27 31TK4640_197
Keyless Access System
EmergencyEngineStop The engine start/stop button may be used to stop the engine due to an emergency situation even while driving. If you must stop the engine, do either of the following operations:
If you are driving, the power mode switches from ON to ACCESSORY or VEHICLE OFF (LOCK) whenever you perform either procedure. However, the steering wheel will NOT lock.
Press and hold the engine start/ stop button for three seconds. Firmly press the engine start/stop button three times.
Do not press the button while driving unless it is absolutely necessary for the engine to be switched off.
If you cannot stop the engine by pressing the engine start/stop button once when the vehicle is stopped and the shift lever is in Park (automatic transmission), do either emergency engine stop procedure. In this case, the power mode will change to VEHICLE OFF (LOCK), however, the steering wheel may NOT lock.
192
2013 TL12/07/20 10:54:35 31TK4640_198
Beeper and Message KeylessRemoteNotDetected
If you take the keyless access remote out of the vehicle and close the door with the power mode ON or ACCESSORY, the inside and outside beepers sound and a ‘‘KEYLESS REMOTE NOT DETECTED’’ message will be displayed on the multi-information display, and the doors will not lock.
The displayed message goes away when you bring the remote back inside the vehicle.
If the engine is running and you take the remote out of the vehicle, it will continue to run, and the inside and outside beepers will sound. Once the power mode is changed to VEHICLE OFF (LOCK), the engine will not restart until you bring back a remote into the vehicle.
Keyless Access System
The engine does not start if you push the engine start/stop button when the remote is outside the vehicle. Check where the remote is. Make sure that the remote is in the vehicle with you when you operate the engine start/stop button.
Even when the remote is inside the vehicle, the beeper may sound when the location of the remote is not detected due to surrounding conditions. It is not a failure. Make sure that you carry the remote with you.
The outside beeper sounds when the power mode is in ACCESSORY, and a door is opened, then closed.
CONTINUED
193
2013 TL12/07/20 10:54:40 31TK4640_199
Keyless Access System
KeylessRemoteLowBattery
The battery in the remote normally lasts about 2 years. To ensure maximum battery life, do not store the remote close to electrical devices such as computers or TVs. When the multi-information display shows ‘‘CHANGE KEYLESS REMOTE BATTERY,’’ replace the battery as soon as possible (see page
181
).
194
If the remote battery becomes weak
and the power door lock/unlock
operation is disabled, you should
insert the remote into the keyless
access remote slot to set the power
mode and start the engine. After
inserting the remote into the slot,
operate the engine start/stop button
as previously described (see pages
184
on the keyless access slot, see
page
). For more information
and
187
197
Inserting the remote does not charge the remote battery. You should replace the battery as soon as possible.
2013 TL12/07/20 10:54:49 31TK4640_200
Keyless Access Remote SystemMain Switch
Turning off the keyless
NOTE: access system will disable lockout prevention.
With the keyless access remote system main switch off, you should insert the keyless access remote into the keyless remote slot to start the engine. For more information, see page
197
OFF
MAIN SWITCH
This switch is in the glove box. You can cancel the keyless access system features, which are locking/ unlocking the doors, unlocking the trunk, and starting the engine while carrying the keyless access remote. To cancel the system, turn the keyless access system main switch off by pushing it down.
Keyless Access System
Keyless Access SystemIndicator
According to the message on the multi-information display, this indicator has two indications. A ‘‘CHECK KEYLESS ACCESS SYSTEM’’ message indicates a problem with the keyless access system. A ‘‘CHECK KEYLESS STARTING SYSTEM’’ message indicates a problem with the keyless starting system.
This indicator normally comes on for several seconds when you change the power mode to ON.
CONTINUED
195
2013 TL12/07/20 10:54:58 31TK4640_201
Keyless Access System
CheckKeylessAccessSystem
KEYLESS ACCESS SYSTEM INDICATOR
In this case, use the built-in key to lock/unlock the doors and insert the keyless access remote into the slot to start the engine (see page ).
197
CheckKeylessStartingSystem
KEYLESS ACCESS SYSTEM INDICATOR
The indicator comes on and stays on in any power mode.
The multi-information display shows ‘‘CHECK KEYLESS STARTING SYSTEM.’’
In this case, you should not shut off your engine until you are in a safe location or at your dealer, as your vehicle may not restart.
Have your vehicle checked by your dealer if:
The keyless access system indicator comes on and stays on while you are driving. The indicator comes on after the engine has started. The multi-information display shows ‘‘CHECK KEYLESS ACCESS SYSTEM.’’
196
Have your vehicle checked by your dealer if:
The keyless access system indicator comes on and stays on while you are driving.
2013 TL12/07/20 10:55:06 31TK4640_202
Keyless Access Remote Slot
SLOT
KEYLESS ACCESS REMOTE
In the following two cases, you have to insert the keyless access remote into the keyless access remote slot to set the power mode and start the engine:
If the remote battery becomes weak and the power door lock/ unlock operation is disabled.
When the keyless access remote system main switch in the glove box is set to off.
To remove the keyless access remote, place the vehicle in the VEHICLE OFF (LOCK) mode, then pull out the keyless access remote.
Keyless Access System
If the keyless access remote has been inserted into the slot with the keyless access remote system main switch in the glove box turned off, it will lock into place when the power is on. The slot will unlock when the power is turned off.
If the keyless access remote
NOTE: does not come out of the slot easily,try to push it in before pulling it out. Make sure the vehicle is in VEHICLE OFF (LOCK) mode.
Onautomatictransmissionmodels The multi-information display shows the ‘‘ACCESSORY MODE’’ or ‘‘TO UNLOCK KEYLESS REMOTE TURN OFF POWER’’ message to remind you to change the power mode to VEHICLE OFF (LOCK).
CONTINUED
197
2013 TL12/07/20 10:55:16 31TK4640_203
Keyless Access System
Onmanualtransmissionmodels The multi-information display shows the ‘‘ACCESSORY MODE’’ message to remind you that the power mode is in ACCESSORY.
Onallmodels To avoid damaging the slot, do not insert any other objects into the slot or put a sticker on the keyless access remote.
Inserting the remote does not charge the remote battery. If necessary, you should replace the battery as soon as possible.
UnlockedKeylessAccessRemote When the keyless access remote system main switch in the glove box is set to ON, the remote remains unlocked when you insert it into the keyless access remote slot and the power mode is turned on.
198
OperationGuidance Toinsertthekeylessaccessremote:
information display in the following situations:
When the keyless access system main switch (see page ) is off.
195
When the keyless access remote is not in the vehicle.
When you open the driver’s door, and each time you press the engine start/stop button, you will see the ‘‘INSERT KEYLESS REMOTE INTO SLOT’’ message on the multi-
2013 TL12/07/20 10:55:21 31TK4640_204
Tounlockthekeylessaccessremote: Onautomatictransmissionmodels
When the keyless access remote system main switch in the glove box is set to OFF, the multi-information display will show the ‘‘TO UNLOCK KEYLESS REMOTE TURN OFF POWER’’ message after you shift to Park.
The message reminds you that the keyless access remote is locked in the keyless access remote slot, and that the power mode is in the ACCESSORY or ON position. To remove the keyless access remote, turn the power mode off by pressing the engine start/stop button twice (in ACCESSORY mode) or once (in ON mode) without pressing the brake pedal.
Keyless Access System
In ACCESSORY mode, the ‘‘ACCESSORY MODE’’ message will be displayed a few seconds after the ‘‘TO UNLOCK KEYLESS REMOTE TURN OFF POWER’’ message is displayed.
CONTINUED
199
2013 TLIf you turn off the vehicle and leave the remote in the keyless access remote slot, you will also hear a reminder beeper.
Onautomatictransmissionmodels The shift lever must be in Park before you can press the engine start/stop button twice without pressing the brake pedal to set the vehicle into the VEHICLE OFF (LOCK) mode.
12/07/20 10:55:27 31TK4640_205
Keyless Access System
Toremovethekeylessaccessremote:
If the vehicle is left in the ACCESSORY mode, the ‘‘TO TURN VEHICLE OFF’’ message is shown on the multi-information display when you open the driver’s door. If the vehicle is left in the VEHICLE OFF (LOCK) mode with the keyless access remote in the slot, the ‘‘REMOVE KEYLESS REMOTE FROM SLOT’’ message is shown on the multi-information display.
200
2013 TL12/07/20 10:55:35 31TK4640_206
Built-in key and Remote The built-in key can be used to lock/ unlock the doors and the trunk when the remote battery becomes weak and the power door lock/unlock operation is disabled.
BUILT-IN KEY
To avoid damaging the remote and the built-in key, never pull on the built-in key unless you are pressing the release button.
The keyless access system uses an electric field to identify the remote.
If you use medical equipment such as a cardiac pacemaker, ask your doctor if the electric field used by the remote will affect it.
RELEASE BUTTON
To remove the built-in key, pull it out while pressing the release button. To reinstall the built-in key, push the key into the remote until it clicks.
Keyless Access System
Valet Function The trunk and glove box cannot be opened when you turn the trunk main switch off and lock the glove box and trunk pass-through cover with the built-in key. Then, the trunk cannot be opened by using the remote or the exterior trunk release switch.
Remove the built-in key from the remote by pressing the button, then give that remote to someone else as a valet key.
201
2013 TL12/07/20 10:55:41 31TK4640_207
Seat Heaters
Passenger’s Seat
HEATERS
Driver’s Seat
TLandTLwithTechnologyPackage models SH-AWDandSH-AWDwithTechnology Packagemodels Both front seats are equipped with seat heaters. Because of the sensors for the side airbag cutoff system, there is no heater in the passenger’s seat-back.
202
The ignition switch must be in the ON (II) position to use the heaters.
*
* Models equipped with the keyless
access system have an engine start/ stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages
and
184
187
SEAT HEATER SWITCHES
Push the right side of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing the left side of the switch. This will keep the seat warm.
2013 TL12/08/03 20:58:17 31TK4640_208
In the HI setting, the heater turns off when the seat gets warm, and turns back on after the seat’s temperature drops.
In the LO setting, the heater runs continuously. It does not cycle with temperature changes.
Follow these precautions whenever you use the seat heaters:
Do not use the seat heater in the HI setting for an extended period, because it draws large amounts of current from the battery.
If the engine is left idling for an extended period, do not use the seat heaters even on the LO setting. It can weaken the battery, causing hard starting.
Seat Heaters
Heat induced burns are possible when using seat heaters.
Persons with a diminished ability to sense temperature (e.g., persons with diabetes, lower-limb nerve damage, or paralysis) or with sensitive skin should not use seat heaters.
203
2013 TL12/07/20 10:55:53 31TK4640_209
Seat Heaters and Ventilations
Passenger’s seat
SEAT HEATER BUTTON
HEATERS
Driver’s seat
INDICATORS
SEAT VENTILATION BUTTON
You must select the ON mode by operating the engine start/stop button (see page ) to use the heaters and the air ventilation system.
185
TLwithAdvancePackageandCanadian ElitePackagemodels SH-AWDwithAdvancePackageand CanadianSH-AWDElitePackage models Both front seats are equipped with seat heaters and an air ventilation system. The passenger seat only has heaters in the seat bottom because of the side airbag system.
204
To use the heaters, press the seat heater button. The indicator (red) above the button will come on. There are four settings in the heaters: Three indicators on. HI MID Two indicators on. − LO One indicator on. OFF All indicators off.
−
−
−
When you press the seat heater button once, the heater is set to HI. After the seat reaches a comfortable temperature, select MID or LOW by pressing the seat heater button. This will keep the seat warm. To shut down the heater, press the seat heater button until the indicators go off.
2013 TL12/08/03 20:58:23 31TK4640_210
To ventilate the seat, press the seat ventilation button. The indicator (blue) above the button will come on. The air ventilation system has four settings:
−
HI Three indicators on. MID Two indicators on. − LO One indicator on. All indicators off. OFF
−
−
When you press the seat ventilation button once, the system is set to HI. To change to the lower mode, press the seat ventilation button. To turn the air ventilation off, press the seat ventilation button until the indicators go off.
Seat Heaters and Ventilations
Heat induced burns are possible when using seat heaters.
Persons with a diminished ability to sense temperature (e.g., persons with diabetes, lower-limb nerve damage, or paralysis) or with sensitive skin should not use seat heaters.
Follow these precautions whenever you use the seat heaters and the seat ventilation:
Do not use the seat heater or the seat ventilation in the HI setting for an extended period, because it draws large amounts of current from the battery.
If the engine is left idling for an extended period, do not use the seat heaters or the seat ventilation, even on the LO setting. It can weaken the battery, causing hard starting.
The heater runs continuously and does not automatically turn off after a period of time.
205
2013 TL12/07/20 10:56:06 31TK4640_211
Power Windows
DRIVER’S WINDOW SWITCH
INDICATOR
FRONT PASSENGER’S WINDOW SWITCH
MAIN SWITCH
*
Turn the ignition switch to the ON (II) position to raise or lower any window. To open a window, push the switch down and hold it. Release the switch when you want the window to stop. Pull back on the switch and hold it to close the window.
Closing a power window on someone’s hands or fingers can cause serious injury.
Make sure your passengers are away from the windows before closing them.
−
AUTO To open either front window fully, push the window switch firmly down to the second detent, then release it. The window automatically goes down all the way. To stop the window from going all the way down, pull back on the window switch briefly.
To close either front window fully, pull back the window switch firmly to the second detent, then release it. The window automatically goes all the way up. To stop the window from going all the way up, push down on the window switch briefly.
* Models equipped with the keyless
access system have an engine start/ stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages
and
184
187
206
2013 TL12/07/20 10:56:15 31TK4640_212
When you push the main switch in, the indicator comes on and the passengers’ windows cannot be raised or lowered. Use the main switch when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally. To cancel this feature, push on the switch again. The switch will pop out and the indicator will go off.
The windows and the main switch will operate for up to 10 minutes after you turn off the ignition switch (set VEHICLE OFF mode on models with keyless access system). Opening either front door cancels this function.
Auto Reverse If either front window runs into any obstacle while it is closing automatically, it will reverse direction, and then stop. To close the window, remove the obstacle, then use the window switch again.
Auto reverse stops sensing when the window is almost closed. You should always check that all passengers and objects are away from the window before closing it.
The driver’s window auto NOTE: reverse function is disabled when you continuously pull up the switch.
Power Windows
Opening the Windows and Moonroof with the Remote Transmitter/Keyless Access Remote
Vehicle without keyless access system
Vehicle with keyless access system
UNLOCK BUTTON UNLOCK BUTTON
You can open all of the windows and the moonroof from outside with the remote transmitter (the keyless access remote on models with keyless access system).
CONTINUED
207
2013 TL12/07/20 10:56:25 31TK4640_213
Power Windows
1.
Press the UNLOCK button once to unlock the driver’s door.
2.
3.
Press the UNLOCK button a second time, and hold it. The remaining doors unlock, and all four windows and the moonroof start to open. To stop the windows and moonroof, release the button.
To open the windows and
moonroof further, press the
button again (within 10 seconds of
step 1) and hold it. If the windows
and the moonroof stop before the
desired position, repeat steps 1
and 2.
You cannot close the windows or the moonroof with the remote transmitter.
208
Opening/Closing the Windows and Moonroof with the Key or the Built-in key
To open: 1.
Insert the key in the driver’s door lock.
Vehicle without keyless access system
Open
Close
Open
Close
BUILT-IN KEY
Vehicle with keyless access system
You can open and close the windows and moonroof with the key in the driver’s door lock.
2.
Turn the key clockwise, then release it.
3.
Turn the key clockwise again, and hold it. All four windows and the moonroof start to open. To stop the windows and the moonroof, release the key.
4.
To open the windows and the moonroof further, turn and hold the key again (within 10 seconds of step 2).
2013 TL12/07/20 10:56:30 31TK4640_214
To close: 1.
Insert the key in the driver’s door lock.
If the windows and the
NOTE: moonroof stop before the desired position, repeat steps 2 and 3.
2.
Turn the key counterclockwise, then release it.
3.
Turn the key counterclockwise again, and hold it. All four windows and the moonroof start to close. To stop the windows and the moonroof, release the key.
4.
To close the windows and the moonroof further, turn and hold the key again (within 10 seconds of step 2).
Power Windows
209
2013 TL12/07/20 10:56:38 31TK4640_215
MOONROOF SWITCH
Moonroof
Open
Tilt
Close
The moonroof can be tilted up in the back for ventilation, or it can be slid back into the roof. Use the switch on the front ceiling to operate the moonroof. You must turn the ignition switch to the ON (II) position to operate the moonroof.
*
* Models equipped with the keyless
access system have an engine start/ stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages
and
184
187
210
To tilt up the moonroof, push on the center of the moonroof switch. To stop the moonroof from tilting up fully, push the switch briefly.
To open the moonroof, pull back on the switch and hold it. Release the switch when the moonroof reaches the desired position. To close the moonroof, push the switch forward and hold it. Release the switch to stop the operation.
Opening or closing the moonroof on someone’s hands or fingers can cause serious injury.
Make sure all hands and fingers are clear of the moonroof before opening or closing it.
−
To open the moonroof
AUTO fully, pull back the moonroof switch firmly, then release it. The moonroof automatically opens all the way. To stop the moonroof from opening, push the switch briefly.
To close the moonroof fully, firmly push the moonroof switch forward, then release it. The moonroof automatically closes all the way. To stop the moonroof from closing, push the switch briefly.
2013 TL12/07/20 10:56:45 31TK4640_216
To open or close the moonroof partially, lightly pull the switch back or push it forward and hold it. The moonroof will stop when you release the switch.
Auto Reverse If the moonroof runs into any obstacle while it is closing automatically, it will reverse direction, and then stop. To close the moonroof, remove the obstacle, then use the moonroof switch again.
Auto reverse stops sensing when the moonroof is almost closed. You should always check that all passengers and objects are away from the moonroof before closing it.
You can open and close the moonroof for up to 10 minutes after you turn off the ignition switch, on models with keyless access system, set the power mode to VEHICLE OFF (LOCK). Opening either front door cancels this function.
If you try to open the moonroof in below-f reezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or its motor.
Moonroof
You can use the remote transmitter/
keyless access remote or the key/
built-in key to operate the moonroof
from the outside. Refer to page
207
for details.
211
2013 TLIf you drive without releasing the parking brake, a beeper will sound, and you will also see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display (see page
65
).
Driving the vehicle with the parking brake applied can damage the rear brakes and hubs. A beeper will sound if the vehicle is driven with the parking brake on.
12/07/20 10:56:50 31TK4640_217
Parking Brake
PARKING BRAKE LEVER
To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page
65
).
212
2013 TL12/07/20 10:56:55 31TK4640_218
Interior Convenience Items
CONSOLE COMPARTMENT
FRONT DOOR POCKET
COAT HOOK
USB ADAPTER CABLE
ACCESSORY POWER SOCKET
REAR DOOR POCKET
VANITY MIRROR
SUNGLASSES HOLDER
SUN VISOR
CENTER POCKET
GLOVE BOX
AUXILIARY INPUT JACK
ACCESSORY POWER SOCKET
SIDE POCKET
CARGO HOOKS
BEVERAGE HOLDER in REAR SEAT ARMREST
BEVERAGE HOLDER
213
2013 TL12/07/20 10:57:01 31TK4640_219
Interior Convenience Items
Beverage Holders
FRONT
Open the front beverage holder by sliding its cover backward.
214
Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior.
REAR
The rear seat also has a beverage holder in the center armrest. To use it, pivot the armrest down.
To open the rear beverage holder, pull out the lid by the tab. To close it, push it down.
2013 TL12/07/20 10:57:10 31TK4640_220
Accessory Power Sockets
FRONT
CONSOLE COMPARTMENT
Pull up the lid.
Slide the lid forward.
Your vehicle has two accessory power sockets. One is next to the shift lever. The other is in the console compartment.
To access the front accessory socket, slide the lid forward until it latches. To close it, push in on the lid to slide it backward.
To use an accessory power socket, the ignition switch must be in the ACCESSORY (I) or ON (II) position.
*
* Models equipped with the keyless access system have an engine start/ stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages
and
184
187
Interior Convenience Items
Each socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps).
None of the sockets will power an automotive type cigarette lighter element.
Make sure to put the socket cover back in place to prevent any small foreign objects from getting into the socket.
215
2013 TL12/07/20 10:57:17 31TK4640_221
Interior Convenience Items
Glove Box
Console Compartment
An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.
To lock
Always keep the glove box closed while driving.
GLOVE BOX
Open the glove box by pulling out the handle. Close it with a firm push. Lock or unlock the glove box with the master key or the built-in key on models with keyless access system.
The glove box light comes on only