2012 Acura TL Owners Manual

button again within 5 seconds to verify that the doors and the trunk are locked and the security system has set (see page customize the exterior lights not to flash and the beeper not to sound.

). You can

395

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEY AND REMOTE UNLOCK MODE’’ and repeat the procedure again.

When you press the UNLOCK button on the remote transmitter or the keyless access remote to unlock the driver’s door/all the doors (depending on the customize setting), the exterior lights blink twice to verify that the door(s) is unlocked and the security system is turned off.

To turn this feature on or off, follow these instructions.

Multi-Information Display

You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

CONTINUED

131

2012 TLIf the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again.

11/01/14 18:16:29 31TK4630_137

Multi-Information Display

Press the SEL/RESET button to enter the selecting mode.

Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.

▲ ▼

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

132

2012 TL11/01/14 18:16:39 31TK4630_138

SecurityRelockTimer If you unlock the doors with the remote transmitter or the keyless access remote, but do not open any of the doors within 30 seconds, the doors automatically relock, and the security system sets.

You can change this relock time from 30 seconds to 60 or 90 seconds.

Onmodelswithkeylessaccesssystem When you unlock the doors by touching either front door handle while carrying the keyless access remote, the relock time is fixed in 30
seconds.

Multi-Information Display

You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

Press the SEL/RESET button to enter the selecting mode.

Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.

▲ ▼

CONTINUED

133

2012 TL11/01/14 18:16:48 31TK4630_139

Multi-Information Display

DEFAULT ALL

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again.

If you want to set the default settings, press the INFO ( / ) button to select DEFAULT ALL, then press the SEL/RESET button.

▲ ▼

To set the default settings, press the INFO ( / ) button to select SET then press the SEL/RESET button.

▲ ▼

If you want to cancel DEFAULT ALL, select CANCEL, then press the SEL/RESET button. The screen goes back to the previous display.

134

2012 TL11/01/14 18:16:54 31TK4630_140

Multi-Information Display

If the setting is not successfully completed, ‘‘FAILED’’ is shown for several seconds, and then the screen goes back to the normal message mode. Repeat the same procedure to select DEFAULT ALL.

When DEFAULT ALL is set, you will see the above display for several seconds, then the screen returns to the default all setting display.

135

2012 TL11/01/14 18:17:04 31TK4630_141

Controls Near the Steering Wheel

REMOTE AUDIO CONTROL BUTTONS (P. 387)

PADDLE SHIFTERS

(P. 499)

HEADLIGHTS/TURN SIGNALS/ FOG LIGHTS (P. 139, 143)

INSTRUMENT PANEL BRIGHTNESS (P. 143)

VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P. 511) BLIND SPOT INFORMATION SYSTEM (BSI) OFF BUTTON ＊ (P. 525) HEADLIGHT WASHER BUTTON VOICE CONTROL BUTTONS for NAVIGATION SYSTEM / BLUETOOTH HANDSFREELINK SYSTEM (P. 407, 425)

(P. 138)

＊

＊

＊

HORN ＊

A/T model with navigation system is shown.

To use the horn, press the center pad of the steering wheel. If equipped Refer to the navigation system owner’s manual.

1 : 2 : 3 : 4 : Switch location varies on models.

＊ ＊ ＊ ＊ 136

WINDSHIELD WIPERS/WASHERS (P. 137)

ENGINE START/STOP BUTTON

(P. 184)

PASSENGER AIR BAG OFF INDICATOR (P. 34) HAZARD WARNING BUTTON (P. 145)

REAR WINDOW DEFOGGER/ HEATED MIRROR BUTTON (P. 145, 169)

PHONE BUTTON (P. 424)

＊

INTERFACE DIAL (P. 285) SELECTOR KNOB (P. 236)

＊

＊

STEERING WHEEL ADJUSTMENTS (P. 146)

MULTI-INFORMATION DISPLAY BUTTONS (P. 79)

SEAT HEATER SWITCHES SEAT HEATER/VENTILATION BUTTONS ＊

(P. 202)

(P. 204)

KEYLESS ACCESS REMOTE SLOT

(P. 197)

CRUISE CONTROL BUTTONS

(P. 401)

2012 TL11/01/14 18:17:16 31TK4630_142

Windshield Wipers and Washers

ADJUSTMENT RING

1. 2. 3. 4. 5. 6.

Intermittent

MIST OFF INT LO Low speed HI High speed Windshield washers

− − −

Push the right lever up or down to select a position.

MIST

−

The wipers run at high

speed until you release the lever.

OFF

−

The wipers are not activated.

INT

−

The length of the wipe

interval is varied automatically according to vehicle’s speed.

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

−

Windshield Washer

Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete a few more sweeps after you release the lever.

Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h).

CONTINUED

137

2012 TL11/01/14 18:17:24 31TK4630_143

Windshield Wipers and Washers

CanadianSH-AWDmodelsonly When you activate the windshield washer with the headlights turned on, the headlight washer will be activated under certain conditions. For more information, see Washers

Headlight section in the next column.

Headlight Washers CanadianSH-AWDmodelsonly

HEADLIGHT WASHER BUTTON

The headlight washers use the same fluid reservoir as the windshield washers.

The headlight washers can be operated at any time by pressing the headlight washer button located next to the steering wheel column. The headlights must be turned on to use this button. In addition, the headlight washer will automatically turn on the first time you turn on the windshield washers while the ignition switch is in the ON (II) position.

＊

138

＊ Models equipped with the keyless access

system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages 184 and 187.

2012 TL11/01/14 18:17:35 31TK4630_144

1. 2. 3.

4. 5. 6. 7. 8. 9.

Turn signal Off Parking and instrument panel lights AUTO Headlights on High beams Flash high beams Fog lights off Fog lights on

Turn Signals and Headlights

This indicator stays on if you leave the light switch on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.

＊

If you leave the lights on with the key removed from the ignition switch, or with the power mode in VEHICLE OFF (LOCK), you will hear reminder beeps when you open the driver’s door.

＊

−

Turn Signal Push down on the left lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to the center when you release it or complete a turn.

−

Turning the switch to

’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.

Turning the switch to the ‘‘ position turns on the headlights.

’’

When the light switch is in either of these positions, the lights on indicator comes on as a reminder.

＊ Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. VEHICLE OFF (LOCK) Mode is the equivalent of LOCK (0) and ACCESSORY Mode is the equivalent of ACCESSORY (I). For more information, see pages 184 and 187.

CONTINUED

139

2012 TL11/01/14 18:17:46 31TK4630_145

Headlights

−

High Beams Push the left lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.

). Pull the lever back

71

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

−

The automatic lighting

AUTO feature turns on the headlights and all other exterior lights when it senses low ambient light.

To turn on automatic lighting, turn the light switch to AUTO. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator will turn off automatically when the system senses high ambient light.

140

Onmodelswithoutkeylessaccess system The lights will remain on when you turn off the ignition switch. They will turn off automatically when you remove the key and open the driver’s door. To turn them on again, either turn the ignition switch to the ON (II) position or turn the light switch to the

position.

Onmodelswithkeylessaccesssystem The lights will remain on when you set the power mode to VEHICLE OFF (LOCK). They will turn off automatically when you open the driver’s door and take the remote with you. To turn them on again, either set the power mode to ON or turn the light switch to the

position.

Onallmodels Even with the automatic lighting feature turned on, we recommend that you turn on the lights manually when driving at night or in a dense fog, or when you enter dark areas such as long tunnels or parking facilities.

To change the ‘‘AUTO LIGHT SENSITIVITY’’ setting, see page 123

Do not leave the light switch in AUTO if you will not be driving the vehicle for an extended period (a week or more). You should also turn off the lights if you plan to leave the engine idling or off for a long time.

2012 TL11/01/14 18:17:57 31TK4630_146

Automatic Lighting Off Feature The automatic lighting off feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15 seconds after you remove the key and close the driver’s door, or on models with keyless access system, set the power mode to VEHICLE OFF (LOCK), take the remote with you, and close the driver’s door.

＊

To change the ‘‘HEADLIGHT AUTO OFF TIMER’’ setting, see page

122

＊

Onmodelswithkeylessaccess system Your vehicle has the engine start/stop button instead of an ignition switch. For more information on how to select the power mode, see page . 184

LIGHT SENSOR

The automatic lighting feature is controlled by a sensor located on top of the dashboard. Do not cover this sensor or spill liquids on it.

Headlights

If you remove the key (or the vehicle is in VEHICLE OFF mode on models with keyless access system), and the driver’s door is opened and closed, the automatic lighting off feature activates with the headlight switch in the ‘‘ ’’ position, or the lights turned on by setting the switch in the ‘‘AUTO’’ position.

’’ or ‘‘

＊

If you turn the ignition switch to the LOCK (0) position with the headlight switch on, but do not open the door and get out, the lights turn off after 10 minutes (3 minutes, if the switch is in the ‘‘AUTO’’ position). ＊ Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. VEHICLE OFF (LOCK) Mode is the equivalent of LOCK (0). For more information, see pages 184 and 187.

CONTINUED

141

2012 TL11/01/14 18:18:07 31TK4630_147

Headlights

The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights will go off. With the driver’s door open, you will hear a lights on reminder beeper.

142

position, the high beam

Daytime Running Lights With the headlight switch off or in the headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.

＊

The headlights revert to normal operation when you turn them on with the switch.

If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem with the daytime running light system. Take your vehicle to a dealer to have it checked.

＊ Models equipped with the keyless access

system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages 184 and 187.

2012 TL11/01/14 18:18:18 31TK4630_148

Fog Lights

Instrument Panel Brightness

Fog Lights, Instrument Panel Brightness

FOG LIGHT SWITCH

ADJUSTMENT BUTTONS

Turn the fog lights on and off by turning the switch next to the headlight switch.

You can use the fog lights only when the headlights are on low beam.

With the light switch in the AUTO position, you can also use the fog lights when the headlights turn on automatically. They will go off when the headlights turn off.

−

button with the ignition

Adjust the brightness of the instrument panel by pressing the or switch in the ON (II) position. Press the brightness and the decrease it.

button to increase the

button to

＋

＋

−

＊

CONTINUED

＊ Models equipped with the keyless access

system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages 184 and 187.

143

2012 TL11/01/14 18:18:24 31TK4630_149

Instrument Panel Brightness

To reduce glare at night, the instrument panel illumination dims when you turn the light switch to . To cancel the glare

or

reduction function, set the brightness to the highest level, then press the button. You will hear a beep when it is canceled.

＋

U.S. model is shown.

The level of brightness is shown on the multi-information display while you adjust it. It goes out 5 seconds after you finish adjusting.

When the brightness reaches the maximum level, ‘‘BRIGHTNESS MAXIMUM LEVEL’’ appears on the display.

If your vehicle is equipped with the navigation system, the navigation system screen will also go to full brightness. This can be helpful when using the headlights during daylight hours.

144

2012 TL11/01/14 18:18:35 31TK4630_150

Hazard Warning Button, Rear Window Defogger

Hazard Warning Button

Rear Window Defogger

HAZARD WARNING BUTTON

U.S. model is shown.

Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

The rear window defogger clears fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. If you do not turn it off, the defogger will shut itself off within about 10 to 30 minutes according to the outside temperature. It also shuts off when you turn off the ignition switch, or set the power mode to VEHICLE OFF (LOCK) on

models with keyless access system. You have to turn it on again when you restart the vehicle.

Make sure the rear window is clear and you have good visibility before starting to drive.

The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side.

Pushing this button also turns the mirror heaters on or off. For more information, see page

169

145

2012 TL3.

Push the lever up to lock the steering wheel in that position.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.

11/01/14 18:18:42 31TK4630_151

Steering Wheel Adjustments

Make any steering wheel adjustments before you start driving.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

146

LEVER

1.

Push the lever under the steering column all the way down.

2.

Move the steering wheel up or down, and in or out, so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

2012 TL11/01/14 18:18:53 31TK4630_152

Onmodelswithoutkeylessaccess system

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (GRAY)

You should have received a key number tag with your key. You will need this key number if you ever have to get a lost key replaced. Use only an Acura-approved key blank.

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.

Keys and Locks

The master key fits all the locks on your vehicle.

The valet key works only in the ignition and the driver’s door lock. You can keep the trunk pass-through cover and the glove box locked when you leave your vehicle and the valet key at a parking facility.

Protect the key from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

The valet key does not contain a battery. Do not try to take it apart.

CONTINUED

147

2012 TL11/01/14 18:19:02 31TK4630_153

Keys and Locks

RetractableMasterKey

RELEASE BUTTON

Push

The master key can be retracted into the remote transmitter. To use the key, push the release button to release the key from the transmitter. The key should be fully extended. To retract the key, push the release button and at the same time push the key into the remote transmitter until it is securely latched.

148

Always make sure the key is fully extended when you insert it to the ignition switch. If the key is not fully extended, the immobilizer system may not operate properly and prevent the engine from starting.

The key may come in contact with your finger while being retracted or extended. Make sure your fingers do not touch the pivot of the key when retracting or extending it.

Onmodelswithkeylessaccesssystem

BUILT-IN KEYS

KEY NUMBER TAG

Each keyless access remote has a built-in key. This key is used to lock/ unlock the doors when the remote battery becomes weak and the power door lock/unlock operation is disabled. You cannot start the engine with this key.

The built-in key (see page all the locks on your vehicle.

201

) fits

2012 TL11/01/14 18:19:12 31TK4630_154

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Acura-approved key blanks.

Keys and Locks, Immobilizer System

Immobilizer System The immobilizer system protects your vehicle from theft. If an improperly coded key or keyless access remote (or other device) is used, the engine’s fuel system is disabled.

＊

＊

When you turn the ignition switch to the ON (II) position, or select the ON mode with the engine start/ stop button, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key or keyless access remote.

On models without keyless access system, turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.

On models with keyless access system, set the power mode to VEHICLE OFF (LOCK), then select the ON mode again.

The system may not recognize your key’s or remote’s coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch or the keyless access remote when you insert the key or set the power mode to ON.

＊

＊: Onmodelswithkeylessaccess system start/

Your vehicle has the engine stop button instead of an See page 187 for conventional power switches engine start/stop button. For more information on see page 184.

ignition switch. a comparison between

selecting the power mode,

and your

CONTINUED

149

2012 TL11/01/14 18:19:21 31TK4630_155

Immobilizer System

If the system repeatedly does not recognize the coding of your key or keyless access remote, contact your dealer.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable.

If you have lost your key or keyless access remote and you cannot start the engine, contact your dealer.

Always take the ignition key or the keyless access remote with the built-in key with you whenever you leave the vehicle alone.

150

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

2012 TL11/01/14 18:19:33 31TK4630_156

Onmodelswithoutkeylessaccess system

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, you must push the key in slightly. The shift lever must also be in Park.

−

Use this position

START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.

Ignition Switch

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

You will also see a ‘‘REMOVE KEY’’ message on the multi-information display.

The shift lever must be in Park before you can remove the key from the ignition switch.

Onmodelswithkeylessaccesssystem Go to page the engine start/stop button.

for information on

184

151

2012 TL11/01/14 18:19:45 31TK4630_157

Door Locks

MASTER DOOR LOCK SWITCH

Lock

Pushing the rear of either master door lock switch will unlock all doors. Pushing forward the lock tab on the driver’s door unlocks only that door.

Unlock

Lock

LOCK TAB

All doors can be locked from the outside by using the key in the driver’s door. To unlock only the driver’s door, insert the key, turn it clockwise, and release it. The remaining doors unlock when you turn the key a second time within a few seconds.

You can customize the door lock/ unlock settings (see page

125

).

You can open or close the windows and the moonroof by using the key in the driver’s door (see page ).

208

To lock all doors, push the front of the master door lock switch on either front door, pull the lock tab rearward on the driver’s door, or turn the key counterclockwise in the outside lock on the driver’s door.

＊

＊: Onmodelswithkeylessaccess system

The built-in key can be used to lock/ unlock the doors when the remote battery becomes becomes weak and the power door lock/unlock operation is disabled for more information, see page 201.

152

Unlock

RED INDICATOR

The lock tab on any passenger’s door locks and unlocks that door.

When the door is unlocked, you can see the red indicator on the lock tab above the inner door handle.

2012 TL11/01/14 18:19:59 31TK4630_158

Lockout Prevention Onmodelswithoutkeylessaccess system If you forget and leave the key in the ignition switch, lockout prevention will not allow you to lock the driver’s door. With any door open and the key in the ignition switch, locking with the master door lock switch is disabled. If the driver’s door is closed, the lock tab on the driver’s door is not disabled. Pulling the driver’s lock tab rearward will lock all doors. If you try to lock an open driver’s door by pulling the lock tab rearward, the driver’s door lock tab pops out and unlocks the driver's door.

’

To lock any passenger’s door when getting out of the vehicle, pull the lock tab rearward and close the door.

Onmodelswithoutkeylessaccess system To lock the driver’s door, remove the key from the ignition switch, pull the lock tab rearward or push the front of the master switch, then close the door.

Defaultsetting When the vehicle speed reaches about 10 mph (15 km/h) or more, all the doors lock automatically.

Automatictransmission: When you shift to P after driving, the driver’s door unlocks.

Manualtransmission: When you set the power mode to VEHICLE OFF (LOCK) after driving, the driver’s door unlocks.

Door Locks

Childproof Door Locks

LEVER

Unlock

Lock

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position (lever is down), the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, push the lock tab forward and use the outside door handle.

153

2012 TL11/01/24 12:55:03 31TK4630_159

Trunk

TRUNK RELEASE BUTTON

You can open the trunk in any of the following ways:

Press the trunk release button on the driver’s door.

Press and hold the trunk release button on the remote transmitter or the keyless access remote.

TRUNK RELEASE SWITCH

On models with keyless access system

To open the trunk from the outside, push the release switch, then lift up.

Onmodelswithkeylessaccesssystem

If the doors are unlocked, press the trunk release switch on the trunk lid.

If the doors are locked, press the trunk release switch on the trunk lid with the remote in keyless access operating range.

Onmodelswithkeylessaccesssystem The trunk will lock when you lock the driver’s door with the key , the keyless access remote, either master door lock switch, or the lock tab on the driver’s door.

＊

To unlock the trunk, turn the key twice to unlock the doors, push the rear of either master door lock switch, or push UNLOCK twice on the keyless access remote.

＊

154

＊

The built-in key can be used to lock/unlock the doors and trunk when the remote battery becomes weak and the power door lock/ unlock operation is disabled. For more information, see page .

201

2012 TL11/01/14 18:20:23 31TK4630_160

BUTTON

TRUNK RELEASE TAB

Trunk

INNER HANDLE

Onallmodels To close the trunk, use the inner handle to lower the lid, then press down on the back edge.

COVER

If your vehicle’s battery goes dead or is disconnected, you can open the trunk from the rear seat by pulling the trunk release tab through the trunk pass-through.

Pull down the rear seat armrest, then press on the button to fully release the cover. Reach in and locate the trunk release tab, and pull it out.

Keep the trunk lid closed at all times while driving to avoid damaging it, and to prevent exhaust gas from getting into the interior. See Monoxide Hazard .57

Carbon

, page

CONTINUED

155

2012 TL11/01/14 18:20:34 31TK4630_161

Trunk

TRUNK MAIN SWITCH

OFF

Vehicle with keyless access system is shown.

To protect items in the trunk, you can disable the trunk release button on the driver’s door by turning off the trunk main switch in the glove box, locking the glove box, and locking the trunk pass-through cover with the master key or the built-in key.

156

Onmodelswithoutkeylessaccess system If you need to give the key to someone else, give them the valet key.

Emergency Trunk Opener

TRUNK RELEASE LEVER

Onmodelswithkeylessaccesssystem To use the valet function, remove the built-in key from the remote by pressing the button, then give that remote to someone else as a valet key (see page

201

).

Emergency Fuel Lid Release Your vehicle is equipped with the emergency fuel lid release in the trunk. Refer to page access it.

599

for how to

As a safety feature, your vehicle has a release lever on the trunk latch so the trunk can be opened from the inside. To open the trunk, push the release lever in the direction indicated by the arrow.

Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page

40

2012 TL11/01/14 18:20:46 31TK4630_162

Remote Transmitter

LED

LOCK BUTTON

UNLOCK BUTTON

TRUNK BUTTON

PANIC BUTTON

−

Onmodelswithoutkeylessaccess system LOCK Press this button once to lock all doors. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked and the security system has set. You cannot lock the doors if any door is not fully closed or if the key is in the ignition switch.

−

UNLOCK Press this button once to unlock the driver’s door or all the doors (depending on the keyless memory setting). Press it twice to unlock the other doors. Some exterior lights will flash twice each time you press the button.

If you do not open any door within 30
seconds, the doors automatically relock and the security system sets.

The door activated map lights come on when you press the UNLOCK button if the door activated position is selected. If you do not open any door within 30 seconds (or whatever setting of the interior light dimming time is set to), the light(s) will fade out. If you relock the doors with the remote transmitter before 30
seconds have elapsed, the light(s) will go off immediately.

The keyless lock acknowledgment beep and flashing of the lights can be deactivated (see page

131

).

To change the lock/unlock setting and the relock timer setting, refer to the customized settings on page 125

You can also open all power windows and the moonroof from outside the vehicle with the remote transmitter (see page

207

).

CONTINUED

157

2012 TL11/01/14 18:21:02 31TK4630_163

Remote Transmitter

−

Press and hold this

TRUNK button for about 1 second to open the trunk. You cannot open the trunk if the key is in the ignition switch.

−

Press this button for

PANIC about 2 seconds to attract attention: the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position.

RemoteTransmitterCare

Avoid dropping or throwing the transmitter. Protect the transmitter from extreme temperatures. Do not immerse the transmitter in any liquid. If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.

158

Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible.

Battery type: CR1616

On models with keyless access system, see page for how to replace the battery on the keyless access remote.

181

To replace the battery:

1.

Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.

SCREW

KEYPAD

Be careful when removing NOTE: this screw as the head of the screw can strip out.

2.

Separate the keypad from the transmitter by pushing any button from outside.

2012 TL11/01/14 18:21:12 31TK4630_164

4.

BATTERY

Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same ( insert it in the keypad.

side facing up), then

−

An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.

5.

Snap the two halves of the keypad, then install the parts in reverse order.

3.

Place a cloth on the edge of the keypad to prevent scratches, and remove the upper half by carefully prying on the edge with a small flat-tip screwdriver or coin.

Remote Transmitter

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

159

2012 TL11/01/14 18:21:23 31TK4630_165

Remote Transmitter

Recalling a Memorized Driving Position

Driver 1

Driver 2